Itron ACT1 ACT1 Meter Module User Manual 16 0130 Exhibit Cover
Itron, Inc. ACT1 Meter Module 16 0130 Exhibit Cover
Itron >
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3156159 |
| Application ID | MY5EjkQLnpOFAbic89PuXw== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 42.47kB (530813 bits) |
| Date Submitted | 2016-10-05 00:00:00 |
| Date Available | 2016-10-05 00:00:00 |
| Creation Date | 2016-08-03 16:52:44 |
| Producing Software | Nitro PDF PrimoPDF |
| Document Lastmod | 2016-08-03 16:53:19 |
| Document Title | Microsoft Word - 16-0130 - Exhibit Cover.doc |
| Document Creator | PrimoPDF http://www.primopdf.com |
| Document Author: | courtney.mcgann |
Certification Exhibit FCC ID: SK9ACT1 IC: 864G-ACT1 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-247 ACS Project Number: 16-0130 Manufacturer: Itron, Inc. Model: ACT1 Manual 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 ACT1 Meter Module Technical Reference Guide Effective Date: July, 2016 ACT1 Meter Module Revision History The following table describes the changes to this document for each revision of the ACT1 meter module: Revision ACT1 Meter Module Date Description of Change July, 2016 Initial Release Labeling The following requirements will be applied to any products that use this module: The end product or host label will include the following text: • • • Contains: FCC ID: SK9ACT1 IC: 864G-ACT1, Model: ACT1 The user’s manual for any product that contains this module will contain the following text. If the device is large enough, then this will also be placed on the label. “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.” Regulatory Compliance The user’s manual for any product that contains this module will contain the following text: FCC Part 15, Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this device not expressly approved by Itron, Inc. could void the user’s authority to operate the equipment. Innovation, Science and Economic Development Canada (ISED) This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe B répond à la norme Canadienne sur le matériel brouilleur. L'opération est sujette aux deux conditions suivantes: (1) ce dispositif ne peut pas causer d'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris les interférences pouvant entraîner un fonctionnement indésirable. ACT1 Meter Module Under Innovation, Science and Economic Development Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Innovation, Science and Economic Development Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. RF Exposure (FCC/ISED) “This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.” “Cet équipement est conforme aux limites d'exposition aux radiations dans un environnement non contrôlé. Cet équipement do it être installé et utilisé à distance minimum de 20 cm entre le radiateur et votre corps. Cet émetteur ne doit pas être co-localisées ou opérant en conjonction avec tout autre antenne ou transmetteur.” Miscellaneous The user’s manual for any product that contains this module will contain the following text: Professional Installation This module is intended for professional installation by the integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. Modification and Repairs To ensure FCC compliance and system performance, this device, antenna and/or coaxial assembly shall not be changed or modified without the express written approval of Itron. Any unauthorized modification will void the user’s authority to operate the equipment. WARNING! This device contains no user serviceable parts. Attempts to repair this device by unauthorized personnel may subject the person to shock hazard if removal of protective covers is attempted. Unauthorized repair will void the warranty and/or maintenance contract with your company. General Description The Itron ACT1 is an electricity metering module which includes a 902.4 MHz to 927.6 MHz transmitter as well as WiFi. The module operates on AC as well as DC voltage which is supplied by a host device. Recycling Information The product you have purchased contains circuit boards. At the end of the modules useful life, under various state and local laws, it may be illegal to dispose of certain components into the municipal waste system. Check with your local solid waste officials for details about recycling options or proper disposal. About this Manual This technical reference guide describes the installation of the ACT1 for the Itron OPENWAY RIVA CENTRON meter. ACT1 Meter Module Installation The ACT1 module will be installed in the Itron OPENWAY RIVA CENTRON electric meter. Shown are the meter base with metrology board, the board to board connector, the ACT1 module, the display and the inner and outer cover. ACT1 Meter Module Install the display on the ACT1 module by pushing metal pins of display into module connector. ACT1 Meter Module Insert module into upper section of inner cover and connect two wired connectors to module. ACT1 Meter Module Connect metrology and the ACT1 module using the board to board connector. ACT1 Meter Module Install lower inner cover. ACT1 Meter Module Install outer cover. ACT1 Meter Module
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Print high-res Page Count : 11 XMP Toolkit : 3.1-701 Producer : Nitro PDF PrimoPDF Creator Tool : PrimoPDF http://www.primopdf.com Create Date : 2016:08:03 16:52:44-04:00 Modify Date : 2016:08:03 16:53:19-04:00 Title : Microsoft Word - 16-0130 - Exhibit Cover.doc Creator : courtney.mcgann Author : courtney.mcgannEXIF Metadata provided by EXIF.tools