Itron NIC505 900MHz Wireless LAN Network Relay User Manual RelayFCC

Download:
Mirror Download [FCC.gov]
Document ID	855983
Application ID	zTweyzm5it/WpmWG1Evqew==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	16.93kB (211670 bits)
Date Submitted	2007-10-17 00:00:00
Date Available	2007-10-23 00:00:00
Creation Date	2007-08-27 11:32:40
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2007-08-27 12:13:12
Document Title	RelayFCC.book
Document Creator	FrameMaker 7.1
Document Author:	Kurt Thompson

Relay SG Product Guide
Version 5.0
September 2007
Silver Spring Networks
575 Broadway Street
Redwood City, CA 94063
www.silverspringnet.com
650.298.4200 Phone
650.363.5240 Fax
Relay SG Product Guide, Version 5.0
September 2007
Copyright © 2004-2007, Silver Spring Networks®, Inc. All rights reserved.
Silver Spring Networks®, UtilityIQ®, UtilOS®, and PowerPoint® Network Interface Module are registered
trademarks, and Metro Gateway™, Metro Relay™, Gas Interface Management Unit™, and Water Interface
Management Unit™ are trademarks of Silver Spring Networks, Inc.
kv2c and I-210 are trademarks of General Electric Company. Itron, MV-90, and Centron are registered
trademarks of Itron, Inc. iCon is a trademark of Sensus Metering Systems. Rockwell is a registered
trademark of Rockwell Automation, Inc. American is a registered trademark of American Metering
Company, Inc. Red Hat is a registered trademark of Red Hat, Inc. Perl is a trademark of the Perl
Foundation. Oracle is a registered trademark of Oracle Corporation. Apache is a trademark of The Apache
Software Foundation. JBoss is a registered trademark and servicemark of JBoss, Inc. Firefox is a
registered trademark of the Mozilla Foundation. Microsoft is a registered trademark, and Windows,
Windows Vista, and Internet Explorer are trademarks of Microsoft Corporation. Google Maps is a
trademark of Google Inc. Thomas Bros. Maps is a registered trademark of Rand McNally & Company.
InstallShield is a registered trademark of InstallShield Software Corporation. Adobe Acrobat and Adobe
Framemaker are registered trademarks of Adobe Systems Incorporated. WebWorks Publisher is a
trademark or registered trademark of Quadralay Corp.
All other company and product names are used for identification purposes only and may be trademarks,
service marks, or registered trademarks of their respective owners.
Part Number: 210-038005
Document Number: RLYSGv5.0PG
August 27, 2007 12:12pm
Relay SG
This document contains an introduction to the Silver Spring Networks Metro Relay, its FCC and
government guidelines, and safety information related to its installation.
Introduction on page 2
FCC and Government Guidelines on page 2
Safety Information on page 4
Relay SG
Introduction
Introduction
The Relay SG relays messages through the Silver Spring Networks’ 900 MHz wireless LAN
communications protocol. The relay is a signal repeater between a Access Point SG and various
Silver Spring Networks-equipped endpoint devices.
The Relay is enclosed in a weatherproof enclosure and is typically mounted on poletops.
Figure 1 is a photograph of the Relay SG.
Figure 1. Relay SG
FCC and Government Guidelines
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Relay SG Product Guide
FCC and Government Guidelines
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications to this device not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
In order to maintain compliance with FCC RF exposure requirements, this device must be
installed in such a manner as to maintain a 20 cm separation distance between the antenna and
all persons.
FCC regulations require that this unit be professionally installed and maintained by a trained
meter technician. Use of an antenna other than that outlined in the FCC certification filing may
violate FCC regulations.
Labelling
Figure 2 is a copy of the FCC ID label that can be found affixed to the Relay SG. The size of the
label is 1.75 x 3.50 inches.
Figure 2. FCC, IC Label
Relay SG
Safety Information
The label includes the data listed in Table 1:
Table 1. Relay SG Label Data
Label Element
Label Text
Title
RELAY, SG,NIC V5.0,BPF
Catalog Number
210-040101
FCC ID
OWS-NIC502
Industry Canada ID
5975A-NIC502
Label Part Number
996-0000018C
Safety Information
WARNING!: Severe shock and explosion hazard! Touching energized parts can result in
massive equipment damage, and severe injury or death. Short-circuiting energized
parts will result in blinding flash and explosion. Opening and closing electrical circuits
can also produce dangerous and explosive arc flashes. Involuntary muscular reactions
associated with electrical shock may result in other injuries. Observe the following
safety guidelines.
Careful planning of every job is essential. Nothing should be taken for granted. Do not take
chances!
Read and follow all approved policies and procedures provided by your employer associated
with the procedures in this manual.
The procedures in this manual must only be performed by qualified workers in accordance
with local utility safety practices, utility requirements, and applicable OSHA and NFPA
standards.
The information contained in this document is intended to aid qualified personnel, and is
not a replacement for the proper training required to make a person qualified.
Silver Spring Networks assumes no liability for the customer’s failure to follow these safety
guidelines.
General Electrical Safety
Perform the procedures in this manual in accordance with applicable workplace standards
established by the following agencies:
Š
Occupational Safety and Health Act (OSHA).
Š
The National Electrical Code published by the National Fire Protection Association
(NFPA-70).
Relay SG Product Guide
Safety Information
Š
National Electrical Manufacturers Association (NEMA).
Š
Electronics Industries Association (EIA).
Š
Insulated Power Cable Engineers Association (IPCEA).
American National Standards Institute (ANSI). Whenever possible, de-energize all circuits or
equipment before working on them.
Maintain a minimum clearance of 10 ft. between line potential and all unqualified persons
at all times.
Keep unauthorized people out of the work area. Be especially cautious of children, who tend
to be drawn to work activity.
Determining if a circuit is OFF can be difficult in some instances. Check for circuit voltage
with an appropriate voltmeter before working on equipment presumed to have been deenergized. Tiebreakers, double throw disconnect switches, automatic transfer switches and
emergency generators can supply power through an alternate circuit or from another
source.
120V current can be just a lethal as higher voltages because current flow through a body
depends upon the body’s resistance.
Do not trust insulation and/or weatherproofing on a wire as protection from shock.
Use electrically insulated tools. Inspect portable electrical equipment or tools for defects
and remove any defective devices from service immediately. All portable electrical
equipment must have Ground Fault Circuit Interrupter (GFCI) protection.
Select the right tool for the job. Use tools properly. Keep tools in good working order.
Make sure the work area is free of any flammable material. Flammable vapors can be
ignited by an arc flash.
Keep the work area clean and dry. Cluttered work areas cause accidents and injuries.
Provide good lighting in the work area. You cannot work safely if you cannot see what you
are doing.
Report unsafe conditions or defective equipment to your immediate supervisor.
Handle material carefully. Lift and carry properly.
Relay SG
Safety Information
Personal Protective Equipment (PPE)
Always wear Personal Protective Equipment (PPE), in accordance with OSHA and ANSI
standards.
Wear eye protection and electrically insulated gloves. Test gloves in accordance with ANSI
standards before use. Do not use gloves that do not pass appropriate test procedures.
Wear protective clothing such as long sleeve shirts and long pants made of flame resistant
materials.
Remove all jewelry.
Do not pass any objects to or from other persons not protected by insulating platforms or
tested, electrically insulated gloves.
Fall Protection
When performing work at any elevation:
Always use a fall protection system, in accordance with OSHA standards, whenever
performing work at any elevation.
Never use conductors, guy wires, pins, or cross-arm braces, etc. to support your weight.
Whenever using aerial lift devices such as hoists, man-lifts, vehicle-mounted work platforms
and overhead lifts, read and follow the manufacturer’s guidelines for safe and proper
operation.
Use ladders and scaffolding only in accordance with the manufacturer’s guidelines and/or
according to OSHA standards.
Only use ladders made of non-metallic, non-conductive material. They should be the proper
size and type for the work intended. Inspect ladders for wear and breakage. Remove any oil,
grease, or other slippery materials.
Do not set the ladder at too steep or too shallow of an angle. A rule of thumb is to stand
erect with your toes against the bottom rails of the ladder, with your arms extended straight
out. If you can set your palms on top of the rung that is at eye level, the ladder should be at
the proper angle. If a ladder angle label is provided, follow its recommendations.
If the ladder is to remain in place for an extended period, secure it at the top. The support
point at the top of the ladder should be at least 24 inches (60 centimeters) wide to maintain
Relay SG Product Guide
Safety Information
support in the event of sideways movement. For jobs of short duration, have a fellow worker
support the ladder at the base.
Evaluate all tasks to be performed from a ladder for potential fall hazards, such as complex
tasks or situations that require leaning from the side of the ladder.
The use of scaffolding or a work platform should be considered as an alternative solution in such
cases.
Shock Accident First Aid
Do not touch the victim with your bare hands; use something non-conductive to separate the
victim from the energy source.
Call for emergency medical help immediately. Keep the victim lying down, warm, and
comfortable until help arrives. Avoid moving the victim in case of injury to neck or back.
Position an unconscious victim on a side to let fluids drain.
Check the victim’s breathing and heartbeat. If properly trained, apply mouth-to-mouth
resuscitation and/or CPR if necessary.
Remove constricting items from the victim, such as shoes, belts, jewelry, and tight collars;
they could cut off circulation if the victim experiences swelling.
Apply water or saline for a few minutes to any burns until the skin returns to normal
temperature. Do not attempt to remove clothing that is stuck to a burn. If possible, elevate
burned areas to reduce swelling.
Make sure the victim receives professional medical attention, even if they feel fine. Electric
shock can cause heart failure hours after the shock is received.
Relay SG

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 9
XMP Toolkit                     : XMP toolkit 2.9-9, framework 1.6
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : FrameMaker 7.1
Modify Date                     : 2007:08:27 12:13:12Z
Create Date                     : 2007:08:27 11:32:40Z
Title                           : RelayFCC.book
Creator                         : Kurt Thompson
Page Mode                       : UseOutlines
Author                          : Kurt Thompson

EXIF Metadata provided by EXIF.tools