J Communications Co FR1538 2-Way Portable Handheld Radio Transceiver (FRS) User Manual

Download:
Mirror Download [FCC.gov]
Document ID	124484
Application ID	hdt3hOW28K1T7oRPyDEXew==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	47.93kB (599113 bits)
Date Submitted	2000-11-07 00:00:00
Date Available	2001-04-23 00:00:00
Creation Date	2000-11-02 14:19:31
Producing Software	Acrobat 3.0 Scan Plug-in
Document Lastmod	2000-11-03 19:11:54
Document Title	Users Manual
Document Creator	Acrobat 3.0 Scan Plug-in

ATI'ACHMENTM:USER'SMANUAL
© 2000 PCTEST Lab
FR1538-20h
SERVICE MANUAL
2—WAY PORTABLE
HANDHELD
RADIOS
September. 29, 2000
J-communications Co., Ltd
3 . OPERATION
3. 1 Key Name
FUNCTIONS MID CONTROLS
1) Battery Door 11) Down Button & Volume Control
2) Monitor Button 12) Function Button
3) Detachable Belt Clip 13) Power On/Off 5: Enter Button
4) Push—To—Talk (P'l'l‘) Button
5) Antenna
6) External Mic / Speaker
7) Built-in Speaker
8) LCD Panel
9) Built-in Microphone
10) Up Button & Volume Control
342 ICONS on LCD
==<
a»
li)‘
a:
~ 3 Dqu-mn
l.
or
L!
L!
1) R331 (Receiving Signal Strength Indicator) or TX Bar Icon
Yul!
Indicates the receiving signal strength and blinks during
transmission
2) Monitor Indicator
fi Appears when the monitor button is used
3) CTCSS Indicator
" Blinks when the correct C'ICSS tone is entered
4) Auto Channel Scan Indicator
( ) Appears in the auto scan mode or when the auto scan mode is
activated.
5) Dual Watch Scan Indicator
F Appears in dual watch scan mode or when the dual watch scan mode
is activated.
6) Key Lock Indicator
6 Blinks in auto lock selection mode or when the key lock is
activated.
7) VOX Indicator
.i Blinks in VOX selection mode or appears when VOX is activated
8) Battery Level Indicator
Battery Level Meter indicates the remaining battery strength.
' 9) Tx Indicator
ihppears when a signal is being transmitted.
10) Rx Indicator
Kilppears when a signal is being received.
12) Large Segment Display
I I I l I l
- - -
L, L, L'o Indicates the channel number in use at the
normal mode.
When the Function Button is pressed. it Displays the function menu
insequence:CH/oTc/SC/dH/UO/Udt/ALo/CAL/ton/
ML
13) Small Segment Display
Ile III”!
I —" ::' -’o L. Displays the C‘I‘CSS tone option at the normal
mode CTCSS option is displayed in Hz.
Displays the SUBMENU of each MENU in the function moder
(erg. CH 1~69 / cTcr hz / SC: up. dn / d“: channel number /
U0: high. mid. low, off / Udt: Ssec. Ssec, Zsec, 1sec /
ALo: off‘ auto / CAL number11—7'off / tonzno—Freq / tAL:on.off)
3.3 Key Function
3,3—1 ENTER BUTTON (1613)
1) Short Touch - Power On
— Press this button (813) briefly to turn the unit on
A short confirming melody will play.
2) Long Touch - Power Off
— Press this button (#13) for longer than 1.5 seconds to turn the
unit off.
936 Press it to confirm the required option for respective functions
during function edit mode.
3.3—2 FUNCTION BUTTON (3112)
1) Short Touch
— Press this button briefly to enter function edit mode in standby
mode.
2) Long Touch
- Press for longer than 1.5 seconds to activate the KEY LOCK in the
standby mode.
>Z< Please note all buttons will be disabled except the Monitor
Button (312) and HT Button (034) will remain fully operational.
3.3-3 UP BUTTON (#10)
1) Short Touch
- In the standby mode. press this button briefly to move to the
next higher main volume level
In the function edit mode. press briefly to shift from the
current option in each submenu to the next option in the same
submenu.
2) Long Touch
— Pressing this button for more than 1.5 seconds will allow you to
navigate at a more rapid rate through different volume level in
the standby mode or through different menus in the function edit
mode.
3.3—4 DOWN BUTTON (till)
1) Short Touch
— In the standby mode. press this button briefly to move to the
previous lower main volume level.
In the function edit mode. press briefly to shift from the
current option in each submenu to the previous option in the same
submenu‘
2) Long Touch
- Pressing this button for more than 1.5 seconds will allow you to
navigate at a more rapid rate through different volume level in
the standby mode or through different menus in the function edit
mode.
3.3-5 PUSH-TO-‘I'ALK (P'I'I') BUTTON (M)
— Press it firmly and speak into the Built—in Microphone (419) to
transmit.
The red ‘l‘x LED Indicator at the right side of the LCD Panel (#8)
will light.
— Release it to revert to standby mode. When an incoming call is
received. the green Rx LED Indicator on the left side of the LCD
Panel (1610) will light.
— 2—Way Call Ringer
: Press the FTP Button twice quickly to call another party on the
same channel.
The word CALL and the Tx icon will appear in the display.
The user selected call ringer melody will play.
3.3—6 MONITOR BU'I'I‘ON (N2)
— Press it to check activity on the current channel before you try
to transmit.
~ Adjust the Volume Control (tth. till) if necessary.
— When you press the Monitor Button, the LCD Panel (#8) will be
illuminated with an amber color back—light and both the Tx and Rx
LED Indicators will light.
— If you press the Monitor Button during the function edit mode,
you will return to standby mode directly.
3.3—7 EXTERNAL MIC/SPEAKER (116)
— This jack accepts an optional headset/microphone for totally
handsfree operation.
Please refer to the enclosed Accessory Order Form to order
accessories.
See also section regardmg VOX SELECTION MODE.
3.4 Setting and Operation
3.4—1 BASIC CHANNEL SELECTION
In order to communicate with other PER units, both you and the
receiving party must be on the same channelt
JSP—4OBHF has 8 channels (1-8) as indicated by the large digits in the
LCD Display Panel (38). Before. trying to transmit on the selected
channel. you should press the Monitor Button (42) to check the
activity on that channel. If someone is already on the selected
channel, you should try another channel that is clear.
To change the basic channel.
— In the standby mode. press the Up Button (0110) briefly to move to
the next higher main channel number.
— Press the Down Button (fill) briefly to move to the next lower
main channel number.
344—2 CTCSS (Coded Tone Controlled Squelch System) SUB—CHANNEL
SELECTION MODE
This feature allows you to utilize a less used channel range (00-38)
within a main channel. This enables you to communicate with another
party on the same main channel using the same subcode. This helps to
avoid congestion on the main channel and filters out unwanted noise
and static.
There are 38 C‘NSS subchannels for each main channel.
To change the C'l'CSS subchannel,
- Press the Function Button (#12) until the word cTc appears in the
LCD Panel (#8).
- Press the Up Button (no) or the Down Button (till) to choose the
desired subchannel to use, The corresponding subcode frequency
will be displayed in the lower right corner.
- Press the Enter Button (313) to confirm your selection.
110127: R) callunjcate with other LPD units, they Just be 371th to
the sale channel and 672195 subcode‘
7b munimte with other LP!) units that do not have subcodes,
snitch your unit to the sale channel with the subwde set to
flfl‘.
3.4-3 AUTO CHANNEL SCAN MODE
This feature allows you to scan for an active channel and communicate
with the party transmitting.
To access the Auto Channel Scan menu.
— Press the Function Button (1412) until the auto channel icon blinks
and SC appears in the LCD Panel (ma).
— Press the Up Button (#10) or the Down Button (Ml) to choose
scanning up or down from the current channel number.
Press the Enter Button (1413) to confirm your selection.
— The unit will begin scanning for an active main channel.
If a transmission is detected, the Rx and R581 ioons will appear in
the LCD Panel (#8).
— To turn off the auto channel scan feature in the standby mode.
simply press the Function Button (#12) once.
3.4-4 DUAL WATCH SCAN “ODE
This feature allows you to monitor two different channels at the same
time. If you pre—set any priority channel other than the current
channel in use. the pre-set channel will be scanned every 0.5 second
and signals you when a call is received.
To access the Dual Watch Scan menu.
— Press the Function Button (0112) until the dual watch icon blinks
and d" appears in the LCD Panel (3:8) .
— Press the Up Button (#10) or the Down Button (1611) to select the
desired channel number you wish to closely monitor.
— Press the Enter Button (#13) to confirm your selection
— To turn off the dual watch feature in the standby mode. simply
press the Function Button (5412) once.
3.4—5 VOX SELECTION MODE
The Voice Activated Transmission (VOX) function allows your voice to
activate transmission automatically when the Communicator is used with
the optional handsfree mic/headset (refer to enclosed Accessory Order
Form), It also allows handsfree use when a mic/headset is not being
used without having to use the WT Button (104).
To access the VOX Selection menu.
— Press the Function Button (1112) until the VOX icon blinks and U0
appears in the LCD Panel (1&8).
— Press the Up Button (1&0) or the Down Button (Ml) to select from
high. low or off. High or low setting determines VOX response
sensitivity
— Press the Enter Button (MS) to confirm your selection.
— To turn off the VOX feature. enter the VOX selection mode and then
select Off.
3.4—6 VOX RECOVERY TIME SELECTION MODE
This allows the response characteristics of the VOX function to be
precisely adjusted to suit individual needs.
To access the VOX Recovery Time Selection menu.
— Press the Function Button (#12) until Udt appears in the LCD Panel
(#8) with the VOX icon blinking.
— Press the Up Button (#10) or the Down Button (fill) to select from
5. 3. 2 or 1 second setting. This setting determines the delay
time between transmitting and receiving.
— Press the Enter Button (N13) to confirm your selection.
— Please note you may need to try different VOX time settings to
determine the best value to suit your speaking habit,
— To turn off the VOX feature, enter the VOX selection mode and
then select Off.
3.4-7 AUTO KEY LOCK SELECTION MODE
This feature prevents accidental channel change and disturbance to the
preferred settings of the Communicator. Auto Key Lock temporarily
disables the Up, Down and Enter Buttons.
To access the Auto Key Lock Selection menu,
— Press the Function Button (#12) until the auto lock icon blinks
and ALo appears in the LCD panel (168).
— Press the Up Button (MO) or Down Button (#11) to select the Auto
option.
- Press the ENTER key to confirm your selection.
- If you do not press any key for more than 15 seconds in the
standby mode. all respective keys will automatically be locked.
— To turn the auto key lock on or off in standby mode. simply press
and hold the Function Button (1112) for more than 1.5 seconds.
- To quickly activate the Auto Key Lock. hold the Function Button
(#12) for more than 1.5 seconds.
3.4—8 CALL RINGER MELODY SELECTION MODE
This feature provides 7 user selectable call ringer melodies to alert
you of a calling party.
To select your favorite Call Ringer melody.
- Press the Function Button (HZ) until the call icon blinks and
CAL appears in the LCD panel (568).
- Press the Up Button (1310) or Down Button (#11) to preview the 7
available melodies.
— Press the ENTER key to confirm your selection.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Modify Date                     : 2000:11:03 19:11:54
Creator                         : Acrobat 3.0 Scan Plug-in
Producer                        : Acrobat 3.0 Scan Plug-in
Create Date                     : 2000:11:02 14:19:31
Page Count                      : 11

EXIF Metadata provided by EXIF.tools