J Three Holding BT-6000 Bluetooth Headphone User Manual

Download:
Mirror Download [FCC.gov]
Document ID	852150
Application ID	OksPacBeQawK2X0bRq4mYg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	69.48kB (868497 bits)
Date Submitted	2007-10-05 00:00:00
Date Available	2007-10-05 00:00:00
Creation Date	2007-08-12 12:08:29
Producing Software	Adobe PDF library 5.00
Document Lastmod	2007-10-04 09:46:29
Document Title	Users Manual
Document Creator	Adobe Illustrator 10.0

MiJOYA Bluetooth headset
Notice
- Only when the system activates the charging is allowed; the whole charging time is about
90-120 minutes.
- When first time charging the headset please charging it at least for 4 hours.
- Don't use the headset when it is recharging; the headset will switch off itself when it is
recharging.
- Please use the provided charger only.
- When the LED indicator flashes red light, it means the battery level is low and should be
recharged soon.
- Only when the temperature is within the range -10к(+14F) to +45к (+113F); the
headset can be charged.
USER GUIDE
Model No:BT6000
Weee Statement
To protect the global environment and as an environmentalist,
Bluemate must remind you that.........
Under the European union ("EU") Directive on Waste Electrical and
Electronic Equipment, Directive 2002/69/EC, which takes effect on
August 13,2005, products of "electrical and electronic equipment"
cannot be discarded as municipal waste anymore and manufacturers
of covered electronic equipment will be obligated to take back such
products at the end of their useful life. Bluemate will comply with the
products that are sold into the EU. You can return these products to
local collection points.
FCC Safety Statements
The device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
4.Power on/off
1.Press the Power key for about 3 Sec ; after the green indicator light flashing 3 times to
activate the power.
2.When switching off the headset , press the Power Key for about 3 Sec; after the red
indicator light flashing 3 times the power will switch off.
(1)This device may not cause harmful interference.
(2)This device must accept any interference received, including interference that
may cause undesired operation.
The radiated output power is far below the FCC radio frequency exposure limits.
Nevertheless, this device should be used in such a manner that the potential for
human contact during normal operation is minimized.
1. Overview
Thank you for purchasing BT6000 Bluetooth Headset. Before starting to use the product;
please ensure the content of the product package; and read the User Manual carefully, to
understand all the function of the product. BT6000 adopts the latest Bluetooth
technology to connect all the Bluetooth devices with Audio Gateway function like
mobile phone, desktop, notebook etc. Before you use the headset, please to make sure
the device you're going to use with is compatible with Bluetooth specification V2.0 and
supports Bluetooth Headset of Handsfree Profile.
2. Introduction of the product
Volume up
Volume down
Power/Talk key
Charging Port
Microphone
LED
light indicator
Speaker
Ear plug
3. Charging the Headset
There is a lithium polymer battery inside the headset; please fully charge the battery
before you use it.
1.Plug the portable charger to the electricity source.
2.Plug the portable charger into the Charging Port in the end part of the headset.
3.when charging, there will be the red indicator light flashing, after the battery fully
charged; the indicator light will be off.
Notice:
- When switching on your headset, you will hear one " Do" sounds from it ; by the time
the green indicator light will flash 3 times then flashing 2 times . The process will repeat
5 times then it will flash once every 3 Sec, now the headset is under the " stand-by"
mode.
- While the headset is activating, it will detect the paired device automatically ( only if the
paired device is activated and within 10 meters of the headset) then turn into the
connecting mode directly. When the green indicator light flashing two times non-stop; it
means the headset is in the "connecting mode".
- When switching off the headset; you will hear one " Beep" sounds from the headset ,
indicator light will turn off.
5.Pairing with your mobile phone ( or any other Bluetooth devices).
Before using the headset for the first time; you need to pair with your Bluetooth device first.
1.Before pairing, make sure your headset is off.
2.Press the power key for at least 5 sec; when you see the blue and red indicator light
flashing alternately it means the headset is in the pairing mode.
3.Please ensure that your mobile phone is provided the Bluetooth Function, and activate the
function. Each brand of mobile phone might have different ways to operate it; please check
up with your mobile phone user's manual.
4.You will find the words string " BT6000 " show on certain items in your mobile phone.
5.Choose “ BT6000 ” and do the pairing.
6.Key in the pairing pin code "1234" then press " yes" , the indicator light will turn from the
green/red flashing status into green flashing, it means the pairing has been successful.
7.Now the headset has been in the "stand-by"mode, you may receive or dial the phone call.
Notice:
- If the pairing can't be done within 90 Sec, the headset will be in the "stand-by" mode
automatically ( green/red flashing every 3 Sec). You will not be able to use your headset;
you will have to repeat the procedure form step 1-6 pairing again.
- When pairing; the distance between the headset and the mobile phone within 10 cm-1 meter
is preferred; and ensure there isn't any metal obstacle.
- Each Bluetooth headset has a setting pin "1234". According to each brand of mobile phone
has their own way for setting, the detail you may refer to your user's manual of the mobile
phone.
- Once two devices are paired it will be kept; even if the following situations have been
happened.
One device is off.
One of the device has stopped the service.
One of the device has been reactivated.
6.Receiving the calls
1.When you have a incoming call press the Talk key after you hear the ring from the headset.
2.Even if the mobile phone has ring first; please wait until you hear the ring form the headset
then press the Talk key.
3.When the call has been connected, green indicator light will flash 3 times quickly.
4.If the headset is off when the mobile phone rings; please turn on you headset first, then
press the Talk key again; and you can answer the phone call now.
5.If there is auto- answering mode provided in your mobile phone; please activate the mode .
Therefor when you get an in-coming call; your headset will connect it automatically without
pressing the Talk key.
Notice
- BL-902’s maximum operation range is 5 meters indoor, 5-10 meters outdoor.
7.Rejecting the calls
1.When you hear the in-coming call rings from your headset; press the Talk key for 2 Sec,
release it when you hear the " Do Do" sound .
Notice
-The function of rejecting call will be decided whether your mobile phone has this function or
not.
8.Ending the calls.
1.When you finish a call; press the Talk key one more time to end the call.
2.You can also wait until the other finishes the call and it will be disconnected automatically.
9.Voice dialing
1.If your mobile phone provide the " Voice dialing" function; you can do the " Voice Dialing"
via your headset.
2.The headset should be under either the "Stand-by" mode or the " Connecting mode" click
the Talk key once; then you can make the " Voice dialing " by the mobile phone's operation
instruction..
Notice
- Voice Dialing mode's function depends on the specification of your mobile phone.
10. Redial the last call
1.If your mobile phone provide the " Last call Redialling" function, you can also do it via the
headset.
2.The headset should be under either the " stand-by" mode or the " Connecting mode".
By click the Talk Key for twice, after you hear a " Do Do " sound from the headset,
then it will redial again.
11.Mute
1.While connecting press the “ Volume Down" key for 2 Sec; you will hear a “ Do-lu-do-do"
sound, then your voice won't be heard.
2.When in the mute mode; you will hear the " Do Do " sound from time to time.
3.Press the Volume down key again you will hear the " Beep " sound to un-mute the
microphone.
12.Call Diverts(audio transfer)
1.When the headset is on call; please press the " Volume Up" key for 2 Sec to divert the
call back to your mobile phone. You will hear a "Do " sound when the call has been
diverted.
2.If you want to be back to the Headset mode, press the " Volume Up" key for 2 Sec;
the indication of the call diverts will be shown on your mobile phone. By different brands,
some of the mobile phones may not show the indication.
Notice:
- For executing the function, your mobile phone should provide the Hands free mode. More
details for Bluetooth Supporting Mode, please refer to your mobile phone's user's manual.
13.Call waiting
1.When in the headset mode; if you need to keep the call waiting, please click the Talk
key for once; you will hear a " Do" sound ; The call you be waiting. By the time,
if there is any in-coming call; the headset will connect it automatically.
2.If you want to end the call waiting mode ; please click Talk key for twice, after a
" Do" sound then release the button. The waiting call will be connected again.
Notice:
-To activate the function; please ensure the service provider they do provide this function
service.
14. Volume control
You can adjust the headset volume when you are during a call .
1 To increase the volume ; press the volume Up key repeatedly .
2 To decrease the volume ; press the volume Down key repeatedly .
Notice
You will hear the "Do-Do” sound when the volume control reach
either its maximum or minimum .
15. Usage Safety:
1 Before you use the product , please read the user manual carefully. And use the product
properly by the indication .
2 Do not let your children play with the headset , it may cause the accidental swallow or the
risk of getting choke to your children .
3 Do not use any liquid spray cleaning products to clean this product .
4 Do not clean this product when it is recharging .
5 Do not try to disassemble this product yourself. If the Bluetooth headset has defect please
contact the dealer .

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Adobe PDF library 5.00
Create Date                     : 2007:08:12 12:08:29+09:00
Modify Date                     : 2007:10:04 09:46:29+08:00
Creator Tool                    : Adobe Illustrator 10.0
Metadata Date                   : 2007:10:04 09:46:29+08:00
Format                          : application/pdf
Document ID                     : uuid:4c2ee988-f6bb-4b3a-aacb-ba648eec96c9
Instance ID                     : uuid:1bf292bf-74e8-4264-8389-b9706a974e7b
Page Count                      : 2
Creator                         : Adobe Illustrator(R) 10.0
For                             : DAVID WU, D
Title                           : C:\Documents and Settings\DAVID WU\�ୱ\MIJOYA.ai
Bounding Box                    : -61 3 831 558
Container Version               : 9
Creator Version                 : 10

EXIF Metadata provided by EXIF.tools