J Three Holding BT001002 Bluetooth Headset User Manual

Download:
Mirror Download [FCC.gov]
Document ID	408204
Application ID	H7I7wL/SssZSNCytG1EuxQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.49kB (43670 bits)
Date Submitted	2004-03-24 00:00:00
Date Available	2004-03-24 00:00:00
Creation Date	2004-03-03 15:40:10
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2004-03-03 15:40:10
Document Title	User Manual

J-3 International Holding Co.,LTD
Electronic Division
Bluetooth Headset User Guide
Volume Adjust
Charging
Status LED
Function key
Status
LED
MIC
Operation:
◎Turning on the headset
Switch on the headset by pressing “Function key” max. 3 seconds and a beep tone with LED flashing indicates
the headset is on.
◎Putting HS in Pairing Mode
Press and hold the “Function key” for 6 seconds, blinking of red and green LEDs alternately indicates the
headset is in Pairing Mode.
＊The default Passkey required for pairing is 0000. If the headset is not successfully paired within the
Pairing Timeout (120 seconds) period, it shuts off automatically.
♁Your headset needs to pair with Bluetooth Phone before you use, please refer to your phone
manual for user instruction.
◎Answer incoming calls
J-3 International Holding Co.,LTD
Electronic Division
Pressing the “Function key” to answer the call when there is an incoming call present. The green LED will
continue to flash fast while the call is in session.
◎Transferring calls
Calls can be transferred from phone to the headset OR from the headset to phone.
Note: It varies from phone to phone; please refer to your mobile phone user’s manual.
◎Disconnecting calls
While a call is in session on the headset, press the “Function key” to disconnect the call. After the call is
disconnected, the green LED will flash normally.
◎Putting HS in Standby Mode
The headset can be put into Standby Mode in different ways:
Turning on the headset but not going into Pairing Mode
After successfully pairing the headset
Disconnecting from a call
Note: The headset can receive incoming calls in Standby Mode.
◎Locally changing the volume on HS
Press the Right button upward to increase the listening volume on the headset.
Press the Left button downward to decrease the listening volume on the headset.
◎Remotely changing the volume on HS
The headset listening volume can be remotely changed by the blue tooth mobile phone. Please refer to you
blue tooth mobile phone manual for volume adjusting.
◎Low-battery indication
The headset LED will flash red instead of green and a short beep every 30 seconds when the battery is low.
◎Battery recharging
Allow approximately 1 hours to fully recharge an empty battery.
Li-ion Charger LED indicators:
◎Green: ready for charging/battery is full.
◎Red: charging in progress
◎Turning off the headset
Switch off the power by pressing the “Function key” max. 3 seconds, a beep tone and LED off indicate the
headset is off.
J-3 International Holding Co.,LTD
Electronic Division
FCC Safety Statements
The device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired
operation.
The radiated output power is far below the FCC radio frequency exposure limits. Nevertheless, this device
should be used in such a manner that the potential for human contact during normal operation is minimized.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the
antenna or the device is permitted. Any change to the antenna or the device could result in the device
exceeding the RF exposure requirements and void user’s authority to operate the device.
The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction, may cause harmful interference to
radio communication. However, there is no grantee that interference will not occur in a particular
installation. If this equipment dose cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on , the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
The user should not modify or change this equipment without written approval from the manufacture.
Modification could void the FCC authorization to use this equipment.
Battery Information
1. For the first time use, plug the adaptor plug into the headset’s power jack and charge it at least 4 hours
until the charging LED turns off.
2. Only qualified service centers are authorized to remove or replace the battery.
3. The battery can only be charged in a temperature range of –10 ~ 45 ℃.
4. Use the headset in room temperature for maximal battery capacity.
5. Leaving the headset in an environment above 45 ℃ for a long period of time may damage the battery.
Although it is not harmful to human, it reduces the life span of the battery.
※This device complies with part 15 of the FCC Rules. Operation is subject to the following two
J-3 International Holding Co.,LTD
Electronic Division
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2004:03:03 15:40:10+08:00
Modify Date                     : 2004:03:03 15:40:10+08:00
Page Count                      : 4
Creation Date                   : 2004:03:03 07:40:10Z
Mod Date                        : 2004:03:03 07:40:10Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Metadata Date                   : 2004:03:03 07:40:10Z

EXIF Metadata provided by EXIF.tools