JBL For The Amplicom TCL Vibe™ Instructions 741022
User Manual: JBL For the Amplicom TCL Vibe™ Instructions TCL Vibe Alarm Clock with Vibrating Wristband
Open the PDF directly: View PDF 
.
Page Count: 16
| Download | |
| Open PDF In Browser | View PDF |
TCL VIBE User Guide Contents Features..............................................4 Functions.............................................6 Settings...............................................9 Important Safety Instructions This alarm clock is designed to provide an acoustic alarm or alert signal at a set time. Any other use is considered unintended use. Unauthorized modification or reconstructions is not permitted. Do not open the device and attempt any repair work yourself. Installation location Prevent excessive exposure to smoke, dust, vibration, chemicals, moisture, heat and direct sunlight. Heart Pacemaker Always maintain a distance of at least 6 inches from implanted heart pacemakers to prevent any possible interference. 2 Instructions available in other languages at www.amplicomusa.com. FCC FCC Compliance The FCC requires that you will be advised of certain requirements involving the use of this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved in writing by Amplicom may void the user’s authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a different circuit. * Consult the dealer or an experienced radio/TV technician for help. NOTE: Amplicom is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. If you experience trouble with this equipment, please contact the Amplicom Service Center at 1-866-AMPLICOM (267-5426) for repair/ warranty information. 1-866-AMPLICOM (267-5426) 3 Features Features • Clock and calendar display • Dual alarm clock and snooze • Indoor temperature • Low battery indicator • Selectable alarm (audio, vibration or both) • Wireless transmission to wrist alert • Amber backlight • Runs on 3 AAA batteries 4 Service Center Layout Clock Face Layout 1 5 2 3 1 Battery Indicator 2 Time 3 Alarms 4 Alarm Type 5 Temperature 4 1-866-AMPLICOM (267-5426) 5 Functions Button Functions When alarm is beeping or vibrating on wrist, press any button except for “SNOOZE” , and alarm will stop beeping and/or vibrating. LIGHT/SNOOZE • Activate light for 8 seconds • Stop alarm temporarily for 5 minutes when alarm sounds or temporarily stop vibration on wrist MODE/ENTER • Single press to select the clock (Hour:Minute:Second), the clock (Hour:Minute:weekday), calendar, buzzer volume viewing, key tone on/off viewing, the unit auto returns to Hour: Minute Second display mode after viewing calendar or Buzzer volume viewing for 10 seconds) • Press and hold for 2s to activate clock setting mode NOTE: Press MODE 3 times and hold for 2s. When activated, display will flash. You have 10s to press up or down to select or the clock reverts back to the display. 6 Service Center Functions UP ARROW • In clock setting mode, increase the setting value or select 12/24hr format or temperature unit or buzzer volume/frequency high/low; • In alarm setting mode, increase the setting value or select alarm mode(audio alarm/vibration alarm/both/both not) DOWN ARROW • In clock setting mode, decrease the setting value or select 12/24hr format or temperature unit or buzzer volume/frequency high/low;; • In alarm setting mode, decrease the setting value or select alarm mode(audio alarm/vibration alarm/both/both not) ALARM • Single press to cycles through ‘normal mode’, ‘alarm 1 view mode’, and ‘alarm 2 view mode’; • In alarm 1/alarm 2 view mode, press and hold key for 2s to enter alarm 1/2 setting mode 1-866-AMPLICOM (267-5426) 7 Functions RESET Reset system, It is inside the battery compartment. Alarm and Snooze Function When the alarm 1/2 viewing display, press and hold ALARM 2s to enter the set mode of alarm time. The sequence is Hour--- Minute ---alarm mode---exit. When press UP or DOWN ARROW to modify the alarm time. Press and hold UP/DOWN ARROW 2s to enter fast set the parameter. When press UP or DOWN ARROW to select alarm mode, cycles through audio alarm → vibration alarm → both → disable; Press ALARM to enter next set parameter or exit. When the alarm display, press UP or DOWN ARROW to select alarm mode, cycles through audio alarm → vibration alarm → both → disable; When the current time equal with the alarm time and the alarm function enable, the unit will beep for 90 seconds, any key except for SNOOZE key will end the beep. While the unit is beeping, if SNOOZE Motion is triggered, the unit will enter snooze, the snooze time is 5 minutes. After 5 minutes, the unit will beep again. 8 Service Center Settings While the unit is beeping, icon or the icon is flash in [1Hz], If alarm mode is in audio alarm mode, the alarm beep format is: 0 → 9s [B] / s 10 → 29s [BB] / s 30 → 90s [BBBB] / s If alarm mode is in vibration alarm mode, it will send RF packet every 0.5 second, The wrist belt will vibrate when it has received the RF packet. While snooze mode, icon or the icon is flash in [1Hz]. Settings Press and hold MODE/ENTER 2s to set the clock at clock viewing screen. The setting sequence as follow: 24Hr/12Hr → Hour → Min → Year → MD/DM → Month → Day → Language → Temperature unit → Exit.(DCF version) 24Hr/12Hr → Hour → Min → Year → MD/DM → Month → Day → Language → Temperature unit → PMCE → DST on/off → Exit.(WWVB version) Language set follow: English → German → French → Spanish → Italian 1-866-AMPLICOM (267-5426) 9 Settings The desired setting will flash with [1 Hz], and press UP or DOWN ARROW to set the conditions of operation. Press and hold UP/DOWN ARROW 2s to fast set these conditions. Press and hold MODE/ENTER 2s to set the buzzer volume and frequency at buzzer volume viewing screen. Press UP or DOWN ARROW to select volume high or low, then press MODE to confirm volume setting and set buzzer frequency Press UP or DOWN to select buzzer high/low frequency, then press MODE to confirm frequency setting and exit buzzer setting mode Press and hold MODE/ENTER 2s to set the key tone on/off at key tone viewing screen. Temperature Setting The indoor temperature will sample every 30 sec. The temperature range: Indoor: -10.0˚C (14.0˚F) → 60.0˚C (110.0˚F), ➢ > 60.0˚C, display “HH.H”; ➢ < –10.0˚C, display “LL.L”. 10 Service Center Settings Connect-check with Wrist unit Transmitter: If alarm 1 or alarm 2 have been set with vibration, then press and hold DOWN ARROW 2S to send RF connect-check command, (include alarm 1 and alarm 2) Transmitter: RF command will keep transmitting for 90s, press any key except for SNOOZE to end connect-check with wrist unit Transmitter: During connect-check with wrist unit,alarm 1 or alarm 2 icon will flash Wrist unit: During connect-check with wrist unit, wrist unit also must enter connectcheck mode, this mode can be enter for 10s after power on Wrist unit: If wrist unit has received connect-check command, it will check channel number, then vibrate for 1s and flash red LED 4 times, it indicates that wrist unit is connected with this transmitter; 1-866-AMPLICOM (267-5426) 11 General information Default Settings The display mode is Hour—Minute--Second. Language: English. The clock time is Jan 1,2012 0:00. The alarm time is 0:00 and the alarm is disable. The time format is 24 Hr (DCF) or 12Hr(WWVB). The temperature unit is ˚C (DCF) or ˚F (WWVB). Maintenance and Warranty Maintenance • • 12 Please clean your equipment’s surfaces with a soft, lint-free cloth. Never use cleaning agents or solvents. Service Center Warranty Warranty AMPLICOM equipment is produced and tested according to the latest production methods. The implementation of carefully chosen materials and highly developed technologies ensure trouble free functioning and a long service life. The terms of the warranty do not apply where the cause of the equipment malfunction is the fault of the telephone network operator or any interposed private branch extension system. The terms of the warranty do not apply to the rechargeable battery pack or power packs used in the products. The period of warranty is 12 months from the date of purchase. All deficiencies resulting from material of production faults which occur during the period of warranty will be eliminated free of charge. Rights to claims under the terms of warranty are annulled following intervention by the purchaser or third parties. Damage caused as a result of improper handling or operation, incorrect positioning or storing, improper connection or installation, Acts of God or other 1-866-AMPLICOM (267-5426) 13 Warranty external influence are not covered by the terms of warranty. In the case of complaints, we reserve the right to repair or replace defect parts or provide a replacement device. Replacement parts or devices become our property. Rights to compensation in the case of damage are excluded where there is no evidence of intent or gross negligence by the manufacturer. If your equipment shows signs of defect during the period of warranty, please return to the sales outlet in which you purchased the AMPLICOM equipment together with the purchase receipt. All rights to claims under the terms of warranty in accordance with this agreement must be asserted exclusively with regard to your sales outlet. ONE year after the purchase of our products, claims under the terms of warranty can no longer be asserted. 14 Service Center Warranty Included in the Box: Clock 3 AAA Batteries Travel Pouch Wrist Band Vibration Unit Charge Cable 1-866-AMPLICOM (267-5426) 15 Questions? Amplicom USA Service Center 3018 Ambrose Avenue Nashville, TN 37207 V/TTY: 1-866-AMPLICOM (267-5426) www.amplicomusa.com Distributed by: Amplicom USA LLC Made in China
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Create Date : 2014:05:20 10:31:52-04:00 Creator : Adobe InDesign CC (Windows) Modify Date : 2015:05:07 10:40:17-04:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Instance ID : uuid:c9b08db3-eb16-4bd5-acdc-66251012ea51 Original Document ID : adobe:docid:indd:933693d6-641d-11df-8862-adb4bcd589d3 Document ID : xmp.id:bdd0bcb6-a4be-6943-8f96-fd1216c1b205 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:ba818519-ba4a-6d4f-84be-772ff69baa3b Derived From Document ID : xmp.did:7D8F05E1E1E1DF1188C398EBD28D3C53 Derived From Original Document ID: adobe:docid:indd:933693d6-641d-11df-8862-adb4bcd589d3 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC (Windows) History Changed : / History When : 2014:05:20 10:31:52-04:00 Metadata Date : 2015:05:07 10:40:17-04:00 Creator Tool : Adobe InDesign CC (Windows) Format : application/pdf Producer : Adobe PDF Library 11.0 Trapped : False Page Count : 16EXIF Metadata provided by EXIF.tools