JBL Party Box 100 Owner's Manual EN
User Manual: JBL JBL PartyBox 100 - JBL US
Open the PDF directly: View PDF 
.
Page Count: 8
PARTYBOX 100
OWNER’S MANUAL
23
www.jbl.com
English
IMPORTANT SAFETY INSTRUCTIONS
For all products:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not block any ventilation openings. Install this apparatus
in accordance with the manufacturer’s instructions.
6. Do not install this apparatus near any heat sources such as
radiators, heat registers, stoves or other apparatus (including
ampliers) that produce heat.
7. Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has two blades and
a third grounding prong. The wide blade or the third prong
is provided for your safety. If the provided plug does not t
into your outlet, consult an electrician for replacement of the
obsolete outlet.
8. Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles and the point
where they exit from the apparatus.
9. Use only attachments/accessories specied by the
manufacturer.
10. Use only with the cart, stand, tripod, bracket or
table specied by the manufacturer or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination
to avoid injury from tip-over.
11. Unplug this apparatus during lightning storms or when
unused for long periods of time.
12. To disconnect this apparatus from the AC mains completely,
disconnect the power-supply cord plug from the AC
receptacle.
13. The mains plug of the power-supply cord shall remain readily
operable.
14. Do not expose batteries to excessive heat such as sunshine,
re or the like.
15. This apparatus is intended to be used only with the power
supply and/or charging cable provided by the manufacturer.
Caution FCC and IC statement for users (USA and Canada
only)
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
CAN ICES-3(B)/NMB-3(B)
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
Caution: Changes or modications not expressly approved
by HARMAN could void the user’s authority to operate the
equipment.
For Products That Transmit RF Energy
FCC AND IC INFORMATION FOR USERS
This device complies with Part 15 of the FCC rules and Industry
Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) This device may not cause
harmful interference; and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
FCC/IC Radiation Exposure Statement
This equipment complies with FCC/IC RSS-102 radiation
exposure limits set forth for an uncontrolled environment.
FCC Caution:
High power radars are allocated as primary users of the 5.25 to
5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations
can cause interference with and/or damage this device. No
conguration controls are provided for this wireless equipment
allowing any change in the frequency of operations outside the
FCC grant of authorization for US operation according to Part
15.407 of the FCC rules.
IC Caution:
User should also be advised that:
(i) The device for operation in the band 5150-5250 MHz is only
for indoor use to reduce the potential for harmful interference to
co-channel mobile satellite systems; (ii) the maximum antenna
gain permitted for devices in the bands 5250-5350 MHz and
5470-5725 MHz shall comply with the e.i.r.p. Limit: and (iii)
The maximum antenna gain permitted for devices in the band
5725-5825 MHz shall comply with the e.i.r.p. Limits specied for
point-to-point and non-point-to-point operation as appropriate.
(iv) Users should also be advised that high-power radars are
allocated as primary users (i.e. priority users) of the bands 5250-
5350 MHz and 5650-5850 MHz and that these radars could
cause interference and/or damage to LE-LAN devices.
Exposure of humans to RF fields (RSS-102)
The computers employ low gain integral antennas that do not
emit RF eld in excess of Health Canada limits for the general
population; consult Safety Code 6, obtainable from Health
Canada’s Website at http://www.hc-sc.gc.ca/
The radiated energy from the antennas connected to the wireless
adapters conforms to the IC limit of the RF exposure requirement
regarding IC RSS-102, Issue 5 clause 4. SAR tests are conducted
using recommended operating positions accepted by the FCC/
RSS with the device transmitting at its highest away from the
body. Non-compliance with the above restrictions may result in
a violation of FCC RF exposure guidelines.
Use Restriction: Attention in France, the operation is limited to
indoor use within the band 5150-5350 Mhz.
For Products with Radio Receivers That Can
Use an External Antenna (USA ONLY)
CATV (Cable TV) or Antenna Grounding
If an outside antenna or cable system is connected to this
product, be certain that it is grounded so as to provide some
protection against voltage surges and static charges. Section
810 of the National Electrical Code (NEC), ANSI/NFPA No. 700-
1984, provides information with respect to proper grounding of
the mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes
and requirements of the electrode.
Note to CATV System Installer
This reminder is provided to call the CATV(cable TV) system
installer’s attention to article 820-40 of the NEC, which provides
guidelines for proper grounding and, in particular, as close to the
point of cable entry as possible.
Caution: This product uses a laser system. To prevent direct
exposure to the laser, do not open the cabinet enclosure or defeat
any of the safety mechanisms provided for your protection. Do
NOT START INTO THE LASER BEAM. To ensure proper use of
this product, please read the owner’s manual carefully and retain
it for future use. Should the unit require maintenance or repair,
please contact your local JBL service. Refer servicing to qualied
personnel only.
FOR ALL EU COUNTRIES
For products that include audio out
Prevention of hearing loss
Caution: Permanent hearing loss may occur
if earphones or headphones are used at high
volume for prolonged periods of time.
For France, the products have been tested to
comply with Sound Pressure Level requirement
laid down in the applicable NF EN 50332 L.5232-1.
Note:
– To prevent possible hearing damage, do not listen to high volume
levels for long periods.
WEEE Notice
The Directive on Waste Electrical Equipment (WEEE), which
entered into force as European law on 14/02/2014, resulted in
a major change in the treatment of electrical equipment at end-
of-life.
The purpose of this Directive is, a rst priority, the prevention of
WEEE, and in addition, to promote the reuse, recycling and other
forms of recovery of such wastes as so as to reduce disposal.
The WEEE logo on the product or on its box indicating collection
for electrical and electronic equipment consists of the crossed-
out wheeled bin, as shown below.
This product must not be disposed of or dumped with
your other household waste. You are liable to dispose
of all your electronic or electrical waste equipment by
relocating over to the specied collection point for
recycling of such hazardous waste. Isolated collection
and proper recovery of your electronic and electrical waste
equipment at the time of disposal will allow us to help conserving
natural resources. Moreover, proper recycling, and collection
points, please contact your local city center, household waste
disposal service, shop from where you purchased the equipment,
or manufacturer of the equipment.
RoHS Compliance
This product is in compliance with Directive 2011/65/EU of the
European Parliament and of the Council of 8 June 2011 on the
restriction of the use of certain hazardous substances in electrical
and electronic equipment.
For Products that includes Batteries
EU Batteries Directive 2013/56/EU
A new battery directive 2013/56/eu on Battery and Accumulator
replacing directive entered into force on the 01/07/2015. The
directive applies to all types of batteries and accumulator
(AA, AAA, button cells, rechargeable packs) including those
incorporated into appliances except for military, medical
and power tool applications. The directive sets out rules for
collection, treatment, recycling and disposal of batteries, and
aims to prohibit certain hazardous substances and to improve
environmental performance of batteries and all operators in the
supply chain.
45
www.jbl.com
English
7. CARRYING YOUR PARTYBOX 11
8. SETTINGS 11
8.1 TWS MODE 11
8.2 DEMO MODE 11
8.3 STANDBY MODE 11
8.4 SPEAKER MOUNTING 12
9. SPECIFICATIONS 12
10. TROUBLESHOOTINGS 13
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS 2
FEDERAL COMMUNICATION COMMISSION INTERFERENCE
STATEMENT 2
FOR PRODUCTS THAT TRANSMIT RF ENERGY 2
EXPOSURE OF HUMANS TO RF FIELDS (RSS-102) 3
FOR PRODUCTS WITH RADIO RECEIVERS THAT CAN USE AN
EXTERNAL ANTENNA (USA ONLY) 3
FOR ALL EU COUNTRIES 3
FOR PRODUCTS THAT INCLUDES BATTERIES 3
FOR ALL PRODUCTS EXCEPT THOSE WITH WIRELESS
OPERATION 4
FOR ALL PRODUCTS WITH WIRELESS OPERATION 4
HARMAN 4
1. INTRODUCTION 6
2. WHAT’S IN THE BOX 6
3. PRODUCT OVERVIEW 7
3.1 TOP PANEL 7
3.2 BACK PANEL 7
4. POWER ON 8
5. CHARGING 8
5.1 CHARGE YOUR SPEAKER 8
5.2 CHECK THE BATTERY LEVEL 8
6. USING YOUR PARTYBOX 9
6.1 BLUETOOTH CONNECTION 9
6.2 USB CONNECTION 9
6.3 AUX CONNECTION 9
6.4 MIX SOUND WITH A MICROPHONE OR GUITAR 10
6.5 CHARGING EXTERNAL USB DEVICES 10
HARMAN
HARMAN International Industries, Incorporated
8500.255.4545 (USA only)
HARMAN International Industries, Incorporated. All rights
reserved. JBL is a trademark of HARMAN International Industries,
Incorporated, registered in the United States and/ or other
countries. Features, specications and appearance are subject
to change without notice.
EPILEPSY
WARNING
A few people may experience epileptic
seizures when viewing ashing lights.
Precautions
Stand Mounting Safety Precautions
Always follow instruction and precaution advise from
speaker stand manufacturer.
Partybox 100 contains a 36 mm receptacle cup to allow mounting
on tripod stands or on a pole over subwoofers. When using
stands or poles, be sure to observe the following precautions:
• Check the stand or pole specication to be certain the device
is designed to support the weight of the speaker. Observe all
safety precautions specied by the manufacturer.
• Always verify that the stand (or subwoofer/pole) is placed on
a at, level and stable surface and be sure to fully extend the
legs of tripod type stands. Position the stand so that the legs
do not present a trip hazard.
Use this oor stand only on a at, solid surface. Once the support
(extended leg) has been placed and adjusted, carefully tighten
the screws and use the safety pin. After placing the speaker
on the stand, check for stability: When tilting each direction to
10 degrees (for the surface), the speaker should not turn off. If
necessary, reduce the height of the speakers and extend the
base of the stand.
• Route cables so that performers, production crew, and
audience will not trip and topple the speakers over.
• Inspect the stand (or pole and associated hardware) before
each use and do not use equipment with worn, damaged or
missing parts.
• Do not attempt to place more than one PartyBox series
speaker on a stand or pole.
• Always be cautious in windy, outdoor conditions. It may
be necessary to place additional weight (i.e. sandbags) on
the base of the stand to improve stability. Avoid attaching
banners or similar items to any part of a speaker system.
Such attachments could act as a sail and topple the system.
• Unless you are condent that you can handle the weight of
the speaker, ask another person to help you get it onto the
tripod stand or pole.
Instructions for Users on Removal, Recycling and Disposal
of Batteries
The remove the batteries from your equipment or remote control,
reverse the procedure described in the owner’s manual for
inserting batteries. For products with a built-in battery that lasts
for the lifetime of the product, removal may not be possible for
the user. In this case, recycling or recovery, it becomes necessary
to replace such a battery, this procedure must be performed by
authorized services centers. In the European Union and other
locations, it is illegal to dispose of any battery with household
trash. All batteries must be disposed of in an environmentally
sound manner. Contact your local waste-management ofcials
for information regarding the environmentally sound collection,
recycling and disposal of used batteries.
WARNING: Danger of explosion if battery is incorrectly replaced.
To reduce risk of re or burns, don’t disassemble, crush,
puncture, short external contact, expose to temperature above
60°C (140°F), or dispose of in re or water. Replace only with
specied batteries. The symbol indicating ‘separate collection’
for all batteries and accumulators shall be crossed-out wheeled
bin shown below:
In case of batteries, accumulators and button cells containing
more than 0.0005 mercury, more than 0.002% cadmium or more
than 0.004% lead, shall be marked with the chemical symbol for
the metal concerned: Hg,Cd or Pb respectively. Please Refer to
the below symbol:
WARNING: DO NOT INGEST BATTERIES, CHEMICAL BURN
HAZARD [the remote supplied with] This product contains a coin/
button cell battery. If the coin/button cell battery is swallowed, it
can cause severe international burns in just 2 hours and can lead
to death. Keep new and used batteries away from children. If you
think batteries might have been swallowed or placed inside any
part of body, seek immediate medical attention.
For All Products Except Those with Wireless
Operation
HARMAN International hereby declares that this equipment is in
compliance with EMC 2014/30/EU Directive, LVD 2014/35/EU
Directive. The declaration of conformity may be consulted in the
support section of our Web Site, accessible from www.jbl.com.
For All Products with Wireless Operation
HARMAN International hereby declares that this equipment
is in compliance with the essential requirements and other
relevant provisions of Directive 2014/53/EU. The declaration of
conformity may be consulted in the support section of our Web
Site, accessible from www.jbl.com.
67
www.jbl.com
English
2. WHAT’S IN THE BOX
1) Main unit
2) Power cord*
3) Quick Start Guide, Safety sheet, Warranty card
*Power cord quantity and plug type vary by regions.
1. INTRODUCTION
Congratulations on your purchase! This manual includes
information about “JBL PARTYBOX 100” speaker. We
encourage you to take a few minutes to read this manual, which
describes the product and includes step-by-step instructions to
help you to set up and get started. Read and understand all the
safety instructions before using your product.
If you have any questions about these products, their installation
or their operation, please contact your retailer or customer
service, or visit us at www.jbl.com.
3. PRODUCT OVERVIEW
3.1 Top Panel
1
2
3
4
5
6
7
1)
• Battery level indicator.
2)
• Press to power on or off.
3)
• Press to enter Bluetooth pairing mode.
• Press and hold for 20 seconds to forget all the paired
devices.
4)
• Press to toggle between different light patterns.
• Press and hold for 2 seconds to turn the strobe light on
or off.
5)
• Press repeatedly to switch between bass boost level 1
and level 2 or turn off.
6) /
• Press to increase or decrease the volume level.
• Press both simultaneously to mute the audio output.
7)
• Press to play or pause the music.
Caution:
– Do not look directly at the light-emitting parts when the speaker
lights are turned on.
LED behavior
White (Constant) Power on
Amber (Constant) Standby
Off Power off
White White (Regular ash) Pairing
White (Constant) Connected
Off Not connected
White (Constant) On
Off Off
Red (Slow ash) Low battery
White (Slow ash) Charging
White (Constant) Charged
3.2 Back Panel
2
3
5
6
7
4
1
1) USB
• Charge an external USB device.
• Connect to a USB storage device.
2) AUX
• Connect to an external audio device through an audio
cable.
3) VOLUME (MIC)
• Rotate the knob to adjust the microphone volume.
4) MIC
• Connect to a microphone (not provided).
5) VOLUME (GUITAR)
• Rotate the knob to adjust the guitar volume.
6) GUITAR
• Connect to a guitar (not provided).
7) GAIN
• Guitar and microphone gain control buttons to match
different sensitivity of the mic and guitar.
89
www.jbl.com
English
4. POWER ON
Cautions:
– Use only provided power cord.
Plug one of the end Ac power cord into the Power connector
on the back speaker, then plug the other end to a wall outlet.
5. CHARGING
PartyBox is powered by a built-in rechargeable battery.
Notes:
– Fully charge the built-in battery before using for the rst time, which
will prolong the battery lifespan.
– Built-in battery charging works on AC power only.
5.1 Charge your Speaker
Use the AC power to charge your PartyBox 100
5.2 Check the Battery Level
The speaker is powered by the built-in rechargeable battery.
After power-on, the speaker shows the battery level immediately,
you can check the status of the PartyBox battery by pressing
on any button.
6. USING YOUR PARTYBOX
6.1 Bluetooth connection
You can use your PartyBox as an external speaker for your
Bluetooth enabled smartphone or tablet.
1) Press to enter Bluetooth pairing mode.
2) Choose “JBL PartyBox 100” to connect.
3) Once successfully connected, audio will stream from your
Bluetooth device to this speaker.
10m (33ft)
2
DEVICES
JBL PartyBox 100
Bluetooth
Bluetooth
1
Notes:
– This speaker can memorize a maximum of 8 paired devices. The
ninth paired device will replace the rst one.
– If a PIN code is requested while connecting a Bluetooth device,
enter “0000”.
– Bluetooth performance can be affected by the distance between
this product and your Bluetooth device and the environment of
operation.
To terminate the Bluetooth-enabled device:
• Turn off this speaker;
• Disable Bluetooth on your device; or
• Move this speaker beyond the Bluetooth operational range.
To reconnect the Bluetooth-enabled device:
• When you turn on this speaker next time, it tries to reconnect
the last connected device automatically;
• If not, manually select “JBL PartyBox 100” on your Bluetooth
device to start a connection.
Note:
– To exit Bluetooth mode, insert a USB storage device.
6.2 USB connection
With your PartyBox, you can enjoy music that is stored on a
USB storage device such as an MP3 player.
Plug your USB storage device into the USB port of your PartyBox.
The music will play automatically. If not, please check if the USB
device contains playable audio contents.
Audio formats
Extension Codec Sample rate Bitrate
WAVE PCM
8 / 11.025
/ 12 / 16 /
22.05 / 24
/ 32 / 44.1
/ 48
384 / 529.2 / 576 /
768 / 1058.4 / 1152 /
1536 / 2116.8 / 2304
MP3
MPEG1
layer2/3
32 / 44.1
/ 48
32 / 40 / 48 / 56 / 64 /
80 / 96 / 112 / 128 /
160 / 192 / 224 / 256 /
320
MPEG2
layer2/3
16 / 22.05
/ 24
8 / 16 / 24 / 32 / 40 /
48 / 56 / 64 / 80 / 96 /
112 / 128 / 144 / 160
MPEG2.5
layer3
8 / 11.025 /
12
8 / 16 / 24 / 32 / 40 / 48 /
56 / 64 / 80 / 96 / 112 /
128 / 144 / 160
WMA
8 / 11.025 /
16 / 22.05 /
32 / 44.1/48
5 / 6 / 8 / 10 / 12 / 16 /
20 / 22 / 32 / 36 / 40 /
44 / 48 / 64 / 80 / 96 /
128 / 160 / 192 / 256 /
320
6.3 AUX connection
Notes:
– When the USB source is not playing, Bluetooth can break in and
play music from the phone.
– When USB is playing, Bluetooth cannot break in USB.
– Priority goes to USB, Bluetooth and then Aux.
To play music on your portable audio device through this
speaker, make sure that no Bluetooth connection or USB device
is available.
1) Connect a 3.5mm audio cable (not supplied) to:
• the headphone socket of your portable audio device;
• the AUX connector of this speaker.
10 11
www.jbl.com
English
2) Turn on your portable audio device and it starts playing.
2
1
Note:
– To exit AUX mode, choose Bluetooth or USB as a source rst
6.4 Mix Sound with a Microphone or Guitar
By using a microphone (not supplied) or an electric guitar (not
supplied), you can mix its sound with an audio source.
1) Rotate counterclockwise the MIC/GUITAR volume knob to
turn down the volume.
2) Connect your microphone or guitar to the MIC/GUITAR jack
of this speaker.
3) Sing through the microphone or play guitar.
• To adjust the volume of the audio source, press / ;
• To adjust the volume of the microphone or guitar, rotate the
MIC/GUITAR volume knob.
To adjust the echo mic level when the mic is plugged:
• Press / to toggle the echo level (echo level 1 set as
default).
• Press / to switch from level 1 to level 2.
• Press / to turn off the echo level.
Caution:
– When not using the microphone or guitar, decrease the MIC/
GUITAR volume to minimum and remove them from the jack.
6.5 Charging External USB Devices
You can use this speaker as a battery charger for your
rechargeable USB devices.
Connect your USB device to the USB port on the rear of this
speaker.
7. CARRYING YOUR PARTYBOX
Cautions:
– Before carrying the speaker, make sure that all the cords are
disconnected.
– To avoid personal injury and/or property damage, hold the product
rmly while carrying.
8. SETTINGS
8.1 TWS Mode
The two PartyBox 100 speakers can connect to each other in
TWS mode.
1) Press and hold on both speakers simultaneously for 5
seconds, you will hear a tone to indicate speakers are in
pairing mode. Once TWS connection built up, you will hear
another tone.
2) In TWS mode, press and hold for 5 seconds on either
speaker or power off the speaker to exit the TWS mode.
10m (33ft)
8.2 Demo Mode
Caution:
– Ensure PartyBox is powered by AC to go into Demo Mode.
– If the AC power unplugged, the PartyBox will power off. If the AC
power is resumed the PartyBox will automatically enter to the demo
mode.
To enter or to exit demo mode, press and hold and
simultaneously for 5 seconds.
In demo mode, all the input sources are disabled, all buttons but
/ / / are disabled.
Note:
– The PartyBox built-in with 3 x 30 seconds music tracks.
Playback
• Press once to start, pause or resume the play (one sample
will be played only for 30 seconds).
• Press once after the pause, to play the next track.
8.3 Standby Mode
The product will enter into sleep mode after 20 minutes without
operation.
• If the“PartyBox” powered by the battery, it will auto power
off if no action for 20 minutes.
• If the “PartyBox” powered by AC or DC power source, the
product will enter standby mode if no action for 20 minutes.
Press (power) or Bluetooth stream break-in in standby mode,
the speaker will enter normal mode.
12 13
www.jbl.com
English
8.4 Speaker mounting
a) Speaker Stand
Place the ParyBox on speaker stands (sold separately) for
general-purpose sound reinforcement.
b) Using a Speaker Stand
If you have purchased speaker stands, you can place the
speakers on the stands utilizing the pole mount adaptor built
into the PARTYBOX 100 speaker cabinets.
9. SPECIFICATIONS
• Product name: PartyBox 100
• AC power input: 100 - 240 V ~ 50/60 Hz
• Built-in battery: Li-ion 2500 mAh, 14.4 V
• Power consumption: 60 W
• Sta ndby power consumption:
< 2 W with BT connecting;
< 0.5 W without BT connecting
• USB output: 5V 2.1A
• Speaker drivers: 2 woofers + 2 tweeters
• Speaker impedance: 4 Ω
• Total output power: 160 W
• Signal-to-noise (S/N) ratio: 80 dBA
• Frequency response: 45 Hz - 18 KHz (-6 dB)
• Battery charge time: 5 hours
• Battery playtime: 12 hours*
• Bluetooth version: 4.2
• Bluetooth prole: A2DP V1.3, AVRCP V1.6
• Bluetooth transmitter frequency range: 2402 - 2480 MHz
• Bluetooth maximum transmitter power: 15 dBm (EIRP)
• Bluetooth transmitter modulation: GFSK, π/4 DQPSK,
8DPSK
• Bluetooth range: Approx. 10 m (33 ft)
• USB format: FAT16, FAT32
• USB le format: .mp3, .wma, .wav
• Input sensitivity (AUX in): 370 mV rms (3.5 mm connector)
• Digital input: Bluetooth/USB -9 dBFS
• Dimension (W x H x D): 288 x 551 x 290 mm /
11.3 x 21.7 x 11.4 in
• Net weight: 9.7 kg / 21.4 lbs
*12 hrs battery playtime is only for reference and may vary
depending on music content and battery aging after numerous
charging and discharging cycles. It’s achievable with a predened
music source, light show switch off, volume level at 7 and BT
streaming source.
10. TROUBLESHOOTINGS
Caution:
– Never try to repair the product by yourself. If you have any
problems while using this product, check the following points
before you request service.
System
The unit will not turn on.
• Check if the power cord is plugged into the outlet and to the
PartyBox.
• Make sure the speaker is fully charged, if not use the power
cord to turn on your speaker.
Sound
No sound from the PartyBox.
• Make sure that the PartyBox is powered on.
• Make sure that volume level is turned to an audible level.
• Make sure that it is connected to a music source.
Bluetooth
A device cannot connect with the PartyBox.
• Check if you enable the Bluetooth function of the device.
• The PartyBox is already connected to another Bluetooth
device. Press and hold on Bluetooth to disconnect and pair
with a new device.
Poor audio quality from a connected Bluetooth device.
• The Bluetooth reception is poor. Move the device closer to
the PartyBox, or remove any obstacle between the device
and the PartyBox.
14
Note: The product is in compliance with the European Union energy legislation.
1) Bluetooth connection mode
The product is intended to be used for streaming music via Bluetooth connection. A consumer can stream Bluetooth audio to the
speaker. When the product is connected through Bluetooth, the Bluetooth connection must remain active at all times to ensure proper
operation.
The product will enter into sleep mode (networked standby), after 20 minutes without operation, the power consumption @ sleep is
less than 2.0 Watts, after which it can be re-activated via Bluetooth connection.
2) Bluetooth disconnection mode
The product will enter into standby mode, after 20 minutes without operation, the power consumption @ standby is less than 0.5 Watts.
Торговая марка : JBL
Назначение товара : Активная акустическая система
Изготовитель : Харман Интернешнл Индастриз Инкорпорейтед, США, 06901 Коннектикут, г.Стэмфорд, Атлантик
Стрит 400, офис 1500
Страна происхождения : Китай
Импортер в Россию : OOO “ХАРМАН РУС СиАйЭс“, Россия, 127018, г.Москва, ул. Двинцев, д.12, к 1
Гарантийный период : 1 год
Информация о сервисных центрах : www.harman.com/ru тел. +7-800-700-0467
Срок службы : 5 лет
Товар сертифицирован
Дата производства : Дата изготовления устройства определяется по двум буквенным обозначениям из второй группы
символов серийного номера изделия, следующих после разделительного знака «-». Кодировка
соответствует порядку букв латинского алфавита, начиная с января 2010 года: 000000-MY0000000,
где «M» - месяц производства (А - январь, B - февраль, C - март и т.д.) и «Y» - год производства (A -
2010, B - 2011, C - 2012 и т.д.).
Используйте устройство только по прямому назначению в соответствии с предоставленной инструкцией. Не пытайтесь самостоятельно
вскрывать корпус товара и осуществлять ремонт. В случае обнаружения недостатков или дефектов, обращайтесь за гарантийным
обслуживанием в соответствии с информацией из гарантийного талона. Особые условия хранения, реализации и (или) транспортировки
не предусмотрены. Избегайте воздействия экстремальных температур, долговременного воздействия влаги, сильных магнитных полей.
Устройство предназначено для работы в жилых зонах. Срок годности не ограничен при соблюдении условий хранения.
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados.
Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e atende aos requisitos
técnicos aplicados.
Para maiores informações, consulte o site da ANATEL – www.anatel.gov.br
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by HARMAN
International Industries, Incorporated is under license. Other trademarks and trade names are those of their respective owners.
JBL_PartyBox_100_OM_EN_V2
