JCM Technologies RB-D-RX10 Transceiver for Automatic Door Safety Edges OSE Output User Manual Installation Guide

JCM Technologies, S.A. Transceiver for Automatic Door Safety Edges OSE Output Installation Guide

Installation Guide

www.milleredge.com info@milleredge.com 800-220-3343IMPORTANT: READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATIONThe Miller Edge RBand Monitored Door Edge Transmitter/Receiver system is intended to provide a wireless connection between a monitored sensing edge and a motorized operator installed with a garage door or grille. RBand meets the 2016 UL 325 requirements for monitored devices and has been certified as a UL 325 Recognized Component. It is designed for use with operators that comply with 2016 UL 325 using a Miller Edge 10K Sensing Edge.1. PARTS LISTKit Contents:1. RBand Edge Transmitter (RB-TX10)2. RBand Door Edge Receiver (RB-D-RX10)3. (2) 3.6V AA lithium batteries*4. (4) #6 pan head transmitter mounting screws*Replacement 3.6V AA lithium batteries can be purchased at your local electronics store or via Miller Edge.Required:• 1/8” flat blade screwdriver• 1/4” flat blade screwdriver• Miller Edge 10K (T2/blue band) Sensing Edge Recommended:• Multi-meter capable of reading 10KΩ• Mounting screws as required for Receiver2. RECEIVER INSTALLATION2-1. Turn off power to the door operator.2-2. Remove Receiver cover and mount the Receiver base near the operator, where it will be in line of sight with the Transmitter for the entire range of travel [IMAGE 1].2-3. Connect power (12-24 VAC/DC) to the terminals marked power, noting the +/- polarity. 24 VAC power can be connected either way not polarity sensitive [IMAGE 2]. 2-4. Connect wiring from the C1 and BS1 terminals on the Receiver to the 10K monitored input terminals on the operator (not polarity sensitive). 2-5. Replace the Receiver cover and turn on power to the operator. Note: it takes ~5 seconds for the Receiver to initialize. Note: RBand 10K Door Edge Receiver is compatible with up to 3 RBand Transmitters.RB-D-K10-C_Install_A4_20170706IMAGE 1. Door Installation with RBand Transmitter & ReceiverINSTALLATION INSTRUCTIONS Model: RB-D-K10
www.milleredge.com info@milleredge.com 800-220-3343IMAGE 2. RBAND GATE EDGE RECEIVER PCB & CONNECTIONSLED INDICATORS Initial Power• No Transmitters Programmed: R1 & R2 LEDs onR1 or R2 LED• Programmed: Off• Fault Condition: OnR3 LED• On when battery is lowA TEST LED • On in test modeCHECK LED (both channels programed)• Programmed: Check LED flashes every 5 secondsDIP SWITCH SETTINGSON1 2 3 4 Switch 1-4: Leave switches in factory default settingsTABLE 1. REMOVABLE CONNECTORS 8-PIN CONNECTORPower+12/24 AC/DC Constant power source-12/24 AC/DC Constant power source (ground)Relay Output 1 CS1 Not usedC1 10K monitored input commonBS1 10K monitored inputRelay Output 2CS2 Not usedC2 Not usedBS2 Not used4-PIN CONNECTORRelay Output 3NO3 Low battery alarm (optional)C3 Low battery alarm (optional)N.C. Power CyclingCOM. Not usedA TEST Not usedGND ANTR2R1R3 A TESTCHECKPROGON1 2 3 4MR12/24 AC/DCCS1 C1+ - BS1 CS2 C2 BS2 NO3 C3COM. A TESTANTENNA PROGRAM BUTTONCHECK LED & BUTTONREMOVABLE 8-PIN CONNECTORDIP SWITCHESRELAY LEDSANTENNA TERMINAL BLOCKREMOVABLE 4-PIN CONNECTOR
www.milleredge.com info@milleredge.com 800-220-3343IMAGE 3. RBand Edge Transmitter PCB & Connections3. TRANSMITTER: PROGRAM MODE 3-1. Confirm the Receiver is powered up. Prior to mounting the Transmitter, remove the cover and insert the batteries, noting their polarity. The green LED on the Transmitter should blink to indicate that it has not been associated with the Receiver yet [IMAGE 3].3-2. To enter learn mode, press and hold the Receiver program button for ~2 seconds until the R1 LED turns on, then release the button [IMAGE 2].3-3. Press the Transmitter program button for ~2 seconds [IMAGE 3]. The Receiver should beep. Wait 10 seconds for an additional beep to indicate that programming is complete.4. TRANSMITTER: INSTALL & TEST4-1. Strip back approximately 2 inches of outer covering of sensing edge cable, then feed through Transmitter strain relief fitting. Connect the two sensing edge wires to the removable terminal. Dress the wires with a small service loop and tighten the strain relief. Mount unit utilizing the mounting holes at the 4 corners of the Transmitter box. Affix lid to Transmitter, noting the alignment pin [IMAGE 3].4-2. Test the sensing edge for functionality.5. TROUBLESHOOTINGIf the Receiver does not react to the Transmitter, you can check the RF signal strength:5-1. Press the check button on the Receiver for ~2 seconds [IMAGE 2]; 4 beeps will be heard. You then will hear a beep every 1-1/2 seconds during the check process. Wait about 30 seconds; if no other beeps occur, your system is functioning. 3 quick beeps indicates a communication error. 5-2. Activate the sensing edge and observe the check LED; 3-5 flashes is ideal. Less than 3 flashes means there is a weak signal.5-3. To exit check function, press the check button, or system will time-out after 5 minutes. There will be a series of beeps heard upon exiting.6. ERASING THE RECEIVERIf you need to replace a Transmitter or you have any other programming issues you may need to erase the Receiver.6-1. To erase any Transmitters programmed into the Receiver, use a screwdriver to short the two pins next to the DIP switch marked MR [IMAGE 2]. 6-2. While shorting the pins, press and hold the program button for several seconds; you will hear a series of 10 beeps following by a rapid chirping sound. 6-3. When the chirping stops, release the program button. Wait ~10 seconds and you will hear 2 beeps. The Receiver is now ready to be reprogrammed. PROGRAM BUTTONREMOVABLESENSING EDGE TERMINAL BLOCK(4) CORNER MOUNTING HOLESGREEN LEDALIGNMENT PINSTRAIN RELIEF FITTINGALIGNMENT PIN(2) 3.6V AA LITHIUM BATTERIES
www.milleredge.com info@milleredge.com 800-220-33437. RECEIVER: SPECIFICATIONS & CONTROLS (cont.)Power: 12-24 VAC/DC nominal (11-30 V max); 100 mA max current draw. Power may be supplied from the operator or alternatively from an external supply. Dimensions: 4.12”L x 3.65”W x 1.65”HCable Connections: Screw clamp type terminal blocks for 18-26 AWG wire Operator Wiring: Screw clamp type terminal blocks for 18-26 AWG wireExternal Antenna: F-connector coax extender for antennaProgram Button: Used to associate a Transmitter with the desired receiver channelCheck Button: Used to determine signal strengthRX Indicator Lights:• Check LED:1. After check button is pressed, blinks to indicate signal strength; 4 or 5 blinks is ideal• R1 and R2 LEDs:1. Off when the associated edge is learned and has no faults2. On solid: No Transmitters learned or edge activated• R3 LED: On when low battery relay is active• A TEST LED: On in test mode. Not used. Connections:• Power (2): Positive and ground, or AC• Relay Output 1:1. CS1: Not used2. C1: 10K monitored input common3. BS1: 10K monitored input• Relay Output 2: Not used• Relay Output 3 (2): Relay closes when low battery is detected• A TEST (2): Not used8. TRANSMITTER: SPECIFICATIONS & CONTROLSTransmitter Frequency: 916 MHz, FSK modulationMounting: 4 corner screws (provided)Power Source: Batteries: 2 AA, 3.6V lithium, 2 year life expectancyDimensions: 1.80”L x 4.78”W x 1.75”HProgram Button: Momentary push button is used to associate the Transmitter to the ReceiverTX Indicator Lights: • Green LED: Normally off• Press program button for status9. FCC COMPLIANCERBand TransmitterModel: RB-TX10FCC ID: U5Z-RB-TX10This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference and2. This device must accept any interference received, including interference that may cause undesired operation.This device complies with FCC radiation exposure limits for an uncontrolled environment. This device shall be installed and operated with a minimum distance of 0.4” between users or bystanders and the device. RBand ReceiverModel: RB-D-RX10FCC ID: U5Z-RB-D-RX10This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference and2. This device must accept any interference received, including interference that may cause undesired operation.This device complies with FCC radiation exposure limits for an uncontrolled environment. This device shall be installed and operated with a minimum distance of 0.8” between users or bystanders and the device. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules:These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:1. Re-orient or relocate the receiver antenna2. Increase the separation between the equipment and the receiver3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected4. Consult the dealer or an experienced radio/TV technician for helpChanges or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Navigation menu