JL Audio MM100 Marine Audio Controller User Manual MM100
JL Audio, Inc. Marine Audio Controller MM100
JL Audio >
User Manual
Thank you for purchasing a JL Audio MediaMaster®
Source Unit for your sound system.
This product has been designed and manufactured to exacting
standards in order to deliver years of musical enjoyment. For maximum
performance, we highly recommend that you have your MM100s
installed by an authorized JL Audio dealer. Your authorized dealer has
the training, expertise and installation equipment to ensure optimum
performance from this product. Due to the complexity of modern
vehicle systems, we do not recommend self-installation unless you have
extensive experience in automotive and marine electrical systems.
Should you decide to install this product yourself, please take the time to
read this manual thoroughly to familiarize yourself with its installation
requirements and setup procedures.
If you have any questions regarding the instructions in this manual or
any aspect of the product’s operation, please contact your authorized
JL Audio dealer for assistance. If you need further assistance, please contact
the JL Audio Technical Support Department at technical@jlaudio.com
or call (954) 443–1100 during business hours.
OWNER’S MANUAL
Protect Your Hearing!
We value you as a long-term customer. For that reason, we urge you to practice
restraint in the operation of this product so as to not damage your hearing and
that of others in your vehicle. Studies have shown that continuous exposure to high
sound pressure level can lead to permanent (irreparable) hearing loss. Mobile sound
systems are capable of producing such high sound pressure levels. Please limit your
continuous exposure at high volumes. While driving, operate your audio system in a
manner that still allows you to hear necessary noises to operate your vehicle/vessel
safely (horns, sirens, etc.).
FCC Compliance Statement
This equipment has been tested and found to comply with the limits of Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient of relocate the receiving antenna.
- Increase separation between the equipment ad the receiver.
- Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
Safety Considerations
• Install this product in a dry, well-ventilated location that does not interfere
with your factory-installed systems. If a dry environment is not available, a location
that is not exposed to heavy splashing may be used.
• While this product is designed to be water-resistant, it should never be submerged
under water or subjected to high-pressure water spray.
• Do not mount this product in an engine compartment or areas of extreme heat.
Areas exposed to a heater or hot air should also be avoided.
• Securely mount this product so that it does not come loose in the event of a
collision, sudden jolt or as a result of repeated vibrations during normal use.
• Check before drilling to make sure that you will not be drilling into an exterior
panel/hull, fuel tank, gas/brake line, wiring harness or other vital system.
• Do not run system wiring outside or underneath the vehicle/vessel. This is an
extremely dangerous practice, which can result in severe damage/injury.
• Protect all system wires from sharp edges and wear by carefully routing them, tying
them down and using grommets and loom where appropriate. Secure all wiring
using cable ties or wire clamps, as needed.
• Do not replace the power wire fuse with one of a different value.
Never bypass the fuse.
• Never make power connections with a “live” wire. Failure to make safe, tight,
high-integrity connections can result in fire and extensive damage.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try correct the interference by one or more of the following
measures:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Mounting and Installation
The diagram below shows a typical mounting procedure into a fiberglass panel.
Always follow proper safety procedures. Wear eye-protection at all times with
a dust mask and gloves when cutting. A mounting template is included to aid in
measuring and marking the mounting surface before cutting or drilling.
Before drilling or cutting, make sure there is adequate space behind the
mounting surface to fit the MM100s, including its wire harness.
1. Press along the perforation to remove the center section of the mounting
template. (Discard the center section.) The template can be used to verify
there is sufficient flat surface area for mounting and as a guide for cutting the
opening. Tape the template to the mounting location and mark the surface for
cutting the opening and drilling pilot holes.
2. Use a jigsaw or rotary tool to cut an opening in the mounting surface. If
necessary, use a file or sandpaper to adjust the opening for proper fitment and
smooth the edges.
3. Place the MM100s into the opening and check that the mounting holes remain
aligned with the pilot hole marks taken from the template. If not, adjust and
mark new holes as necessary.
4. Remove the MM100s and drill four (4) pilot holes in the mounting surface at the
pilot hole marks.
5. Peel the adhesive backing from the mounting gasket and affix to the rear of the
bezel. Connect all wiring and place the MM100s into the opening.
6. Secure the MM100s using the four (4) stainless steel screws. Press the trim ring
onto the front of the MM100s.
Power Connections
The 4-pin plug with wire leads is used to make power related connections. Make
sure to carefully plan the wiring of your system prior to routing wires and making
connections. Refer to the table on the next page when making power connections.
Power Connections continued...
Disconnect the NEGATIVE battery post connection and secure the disconnected
cable to prevent accidental reconnection. This is an essential safety precaution
during installation!
Label Wire Color Connection
+12VDC Red
Connect to a positive (+12V) source. This can be an ignition controlled,
accessory circuit or a vessel battery equipped with a main disconnect
switch. For added control functionality, we also recommend installing
a dedicated toggle switch (not included) at this wire lead’s +12V
connection point. Always install an appropriate fuse within 18 inches
(45 cm) of the +12V connection. If this is the only device using the
connection point, use a 5 amp fuse.
GROUND Black
Connect to a clean metal chassis ground, if available. If no metal chassis
ground is available, it may be necessary to connect this to the NEGATIVE
battery post. All ground connections (source unit and amplifiers)
should be made at the same location to minimize noise.
ILLUMINATION Orange Connect to a +12V lighting circuit to automatically switch the
illumination to night mode when the lights are activated.
AMP TURN-ON Blue This wire provides a positive (+12V) turn-on voltage to activate
aftermarket amplifiers.
Wiring Harness Connections
Harnesses exiting the rear of the unit are used to connect to aftermarket amplifiers/
equipment and media devices. Depending on your specific equipment, you may or
may not use all of the connections. Make sure to plan the layout of your system
prior to routing wires and making connections. Refer to the table below for
additional info.
Label Description Connection
ZONE1
(MAIN)
Black RCA Left Channel Signal Output / Zone 1 (Main)
4V RMS MAX
Output Voltage
Red RCA Right Channel Signal Output / Zone 1 (Main)
ZONE2
Black RCA Left Channel Signal Output / Zone 2
Red RCA Right Channel Signal Output / Zone 2
ZONE3
(SUB)
Black RCA Left Channel Signal Output / Zone 3 (Subwoofer)
Red RCA Right Channel Signal Output / Zone 3 (Subwoofer)
ZONE4
(FIXED
LEVEL)
Black RCA Left Channel Signal Output / Zone 4 (Fixed level) 4V, 2V, or 1V RMS
MAX Output
Voltage
Red RCA Right Channel Signal Output / Zone 4 (Fixed level)
AUX-IN
Black RCA Left Channel Signal Input / Auxiliary 2V or 1V RMS
Input
Sensitivity
Red RCA Right Channel Signal Input / Auxiliary
SiriusXM 10-pin Connector Connect to SiriusXM® tuner (sold separately)
ANT Antenna Connect to Motorola style antenna
USB USB Connector Connect to USB storage device or iPhone®
REMOTE 5-pin Threaded
Connector Connect to MMR-20 remote (sold separately)
CAN 4-pin Deutsch
Connector
Connect to NMEA network (requires NMEA 2000
compatible cables, connectors, etc. (sold separately)
)0$0UHFHLYHURQO\$17
General Control Functions
Below is a list of general commands, including many common operations. The
functionality of each control will vary depending on the current source and
menu selected.
Source/
Power
Use this button to turn ON or OFF and to access the source selection menu.
• Press to turn the unit ON
• Press to display the SOURCE: Select menu
• Press and hold to turn the unit OFF
Volume/
Select
Use this knob to adjust volume levels, navigation of menus and to make selections.
• Rotate to adjust volume level
• Press and hold to access Audio Zone Levels and Zone 2/3 audio setting menus
• Rotate to scroll through options
• Press to choose/enter selections
Back/
Menu
Use this button to go back/return and to access the menu options.
• Press to go back or return to the Now Playing Screen (AM/FM/WB/AUX)
• Press to access main menu options (SiriusXM®/USB/Bluetooth®)
Favorites
Use this button to save, view or edit preset channels (up to 18).
• Press and hold to store a channel (AM/FM/WB/SiriusXM®) as a preset (star
will turn solid)
• Press to view your list of stored presets and the Favorites Edit: Select menu.
Settings
Use this button to access Zone 1 audio settings and main system setting menus.
• Press to access Zone 1 audio settings
• Press and hold to access the System Settings: Main Menu
Forward
Use this button to make a forward selection.
Press to:
•Tune in the next frequency (AM/FM/WB) or channel (SiriusXM®)
• Select the next track (USB/Bluetooth®)
Press and hold to:
• Tune to the next channel (AM/FM/WB)
• Enter Channel Browse mode (SiriusXM®)
• Fast-forward (USB)
Backward
Use this button to make a backward selection.
Press to:
• Tune in the previous frequency (AM/FM/WB) or channel (SiriusXM®)
• Select the previous track (USB/Bluetooth®)
Press and hold to:
• Tune to the previous channel (AM/FM/WB)
• Enter Channel Browse mode (SiriusXM®)
• Fast-rewind (USB)
Mute/
Pause/
Resume
Use this button to mute audio or pause/resume your music.
• Press to mute audio (AM/FM/WB/SiriusXM®/AUX)
• Press to pause or resume the current selection (USB/Bluetooth®)
• Press and hold to access the USB: Play Options menu (USB)
Audio Zones
Audio signals can be sent to your aftermarket amplifiers/equipment via (4) stereo
pairs of low-voltage, line-level RCA outputs. Each output pair delivers full-range, low-
distortion audio, arranged into four zones. Depending on your equipment and vessel,
this will allow you to group speakers of an area together for flexibility and control of
audio levels at separate zones. For example, you may prefer to reduce the listening
level in an interior cabin, while keeping a louder audio level on the main deck.
Audio Zones continued...
Access the Audio Zone Setup menu to congure the functionality of each zone.
1. Press and hold SETTINGS to access the System Settings: Main Menu.
2. Press to select Audio Zone Setup.
3. Use to make selections.
Refer to the table and info below for each zone’s available setting and functionality.
Zone Menu Setting 1 Setting 2
Zone 1 (MAIN) Primary Audio Zone Start up Volume
Zone 2
Level Control Mode
Full-Range Relative
Full-Range Absolute Start up Volume
O
Tone Control Mode Same as Main Zone
Independent Tone Control
Zone 3 / Subwoofer
Level Control Mode
Subwoofer Relative*
Full-Range Relative
Full-Range Absolute Start up Volume
O
Tone Control Mode Same as Main Zone
Independent Tone Control
Zone 4 (Fixed Level) Selectable output voltage (4V, 2V, 1V or O)
* Renames the zone to “Subwoofer” in the Audio Zone Levels menu and displays it after Zone 1.
Level Control Mode Settings
• Start up Volume: This setting adjusts the initial output level when the unit is turned
on and is useful in preventing unexpected output bursts.
• Full-Range Relative: The level of this output will proportionally track Zone 1’s
volume. Press and hold to access the Audio Zone Levels menu from the
Now Playing Screen to adjust the level of volume offset by using and.
• Full-Range Absolute: The level of this output is independent with its own
Start up Volume. You may access its separate volume slider by using to
access the Audio Zone Levels menus.
Tone Control Mode Settings
• Same as Main Zone: The tone controls are assigned to Zone 1.
• Independent Tone Controls: The tone controls are separated with independent
controls. Press while in the Audio Zone Levels menu to access.
Selecting a Source
1. Press to access the SOURCE: Select menu.
2. Rotate to highlight a desired source.
3. Press to select.
Favorites
You may store up to 18 of your preferred stations or channels from your available
tuner options (AM/FM/WB/SiriusXM®) as a preset for quick tuning access.
SiriusXM® Satellite Radio
Only SiriusXM® brings you more of what you love to listen to, all in one place. Get
over 140 channels, including commercial-free music plus the best sports, news, talk,
comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM®
Connect Tuner, antenna and subscription are required. For more information,
visit www.siriusxm.com.
Activating Your SiriusXM® Subscription
After installing your SiriusXM® Connect tuner and antenna, power ON your MM100s
and select SiriusXM® as a source. You should be able to hear the SiriusXM® Preview
channel on Channel 1. If you cannot hear the preview channel, please review the
installation instructions to make sure your SiriusXM® Connect Tuner is properly
installed.
After you can hear the Preview channel, tune to Channel 0 to find the Radio ID
of your tuner. In addition, the Radio ID is located on the bottom of the SiriusXM®
Connect Tuner and its packaging. You will need this number to activate your
subscription. Write this number down for reference.
Note: the SiriusXM® Radio ID does not include the letters I, O, S or F.
Activate your SiriusXM® service online or by phone
For US Subscriptions:
• Visit www.siriusxm.com/activatenow
• Call SiriusXM® Listener Care at 1-866-635-2349
For Canadian Subscriptions:
• Visit www.siriusxm.ca/activatexm
• Call SiriusXM® Listener Care at 1-877-438-9677
As part of the activation process, the SiriusXM® satellites will send an activation
message to your tuner. When your radio detects that the tuner has received the
activation message, your radio will display: “Subscription Updated”. Once subscribed,
you can tune to channels in your subscription plan.
Note: The activation process usually takes 10 to 15 minutes, but may take up to an
hour. Your radio will need to be powered ON and receiving the SiriusXM® signal to
receive the activation message.
Listening to SiriusXM®
1. Press and turn to select SiriusXM.
2. Press to begin listening to SiriusXM.
Channel Selection
1. Press or to select the next or previous channel.
Channel Browse
Channel Browse allows you to preview other channels without leaving your
current channel.
1. Press and hold or to enter Channel Browse mode.
2. Press or to view what is playing on other channels. Hold or
down to rapidly scroll through your available channels.
3. Press to tune to the selected channel.
SiriusXM® Main Menu
The SiriusXM® Main Menu allows access to the following menu options:
Browse by Channel – Lists your available channels.
Browse by Category – Lists your available channels by categories.
My Account info – Lists your account status, Radio ID and Reset menu.
Parental Controls – Allows you to restrict channels containing mature content.
1. Press to access the SiriusXM®: Main Menu.
2. Turn to scroll through menu options.
3. Press to make selections.
Parental Controls
Some SiriusXM® channels contain mature content. When the Parental Controls
feature is enabled, channels with mature content are restricted and will require a
3-digit lock code to access.
Enabling Parental Controls
1. Press to access the SiriusXM®: Main Menu.
2. Turn to Parental Controls and press to enter.
3. Press to select Lock Mature Channels. After, you may
designate a 3-digit lock code to lock mature content channels.
4. Use to enter a 3-digit lock code and select Save when finished.
Make sure to save your 3-digit lock code for future reference.
Changing the Lock Code
1. Press to access the SiriusXM®: Main Menu.
2. Turn to Parental Controls and press to enter.
3. Turn to Edit Lock Code and press enter.
4. Use to enter the current 3-digit lock code and select Enter when
finished.
5. Use to enter the new lock code and select Enter to confirm.
Make sure to save your 3-digit lock code for future reference.
Resetting SiriusXM® Radio Settings
A reset of the SiriusXM® tuner will erase all presets and settings, including parental
controls, restoring all SiriusXM® settings back to their factory defaults.
1. Press to access the SiriusXM®: Main Menu.
2. Turn to My Account and press to enter.
3. Turn to Reset SiriusXM Tuner and press to enter.
4. Use to select Confirm.
Connecting USB Devices
The USB port may be used to connect to USB storage class devices (thumb drive,
digital audio player, etc.). This USB connection also provides a 1A output for device
charging. If this output is exceeded, an error message will display and the output
will be disabled. Devices may be plugged directly into the USB port or use the JL
Audio Combo 3.5 mm Audio Jack and 9 Wire USB Port for Panel-Mounting (XMD-
USB/3.5MM-PNL). An appropriate USB cable for your device is required to make this
input connection.
Once connected, press the button and select USB from the SOURCE: Select
menu to access the connected device with the following controls:
Forward
Use this button to make a forward selection.
• Press to select the next track
• Press and hold to fast-forward
Backward
Use this button to make a backward selection.
• Press to select the previous track
• Press and hold to fast-rewind
Mute/Pause/
Resume
Use this button to pause/resume your music.
• Press to pause or resume playing the current selection
• Properly secure the connected device before driving to prevent damage from
dropping or sudden acceleration/braking.
• Control, functionality and display may vary depending on the type of
device connected.
• Connections to computers or portable hard drives are not supported.
• Connections via USB hubs are not supported.
Connect an iPhone
An iPhone® may also be connected to the USB port using an appropriate Lightning®
to USB cable (not included). Once connected, select USB from the SOURCE: Select
menu to access the connected device with the following controls:
Forward
Use this button to make a forward selection.
• Press to select the next track
• Press and hold to fast-forward
Backward
Use this button to make a backward selection.
• Press to select the previous track
• Press and hold to fast-rewind
Mute/Pause/
Resume
Use this button to pause/resume your music.
• Press to pause or resume playing the current selection
• Press and hold to access Shuffle and Repeat options from the USB:
Play Options menu
Volume/
Select
Use this knob to adjust main/zone volumes, menus navigation and
making selections.
• Rotate to adjust volume (Now Playing Screen)
• Press and hold to access the Audio Zone Levels menu
• Rotate to scroll thru options (menus)
• Press to select/enter (menu options)
Back/Menu
Use this button to go back/return and to access the menu options.
• Press to access the USB: Main Menu options
• Press to go back or return to the Now Playing Screen
Compatible models include iPhone 5, 5c, 5s, 6, 6s, 6+, and 6s+ (equipped with Lightning™ connector)
• Properly secure the connected device before driving to prevent damage from
dropping or sudden acceleration/braking.
• Control, functionality and display may vary depending on the model and version of
iPhone® connected.
• When connected via the USB port, make sure to unpair or disable the Bluetooth®
connection to avoid possible playback conflicts.
• If you experience abnormal performance during operation, disconnect the iPhone®
and check its condition. Restart your iPhone® if performance does not improve.
• “Made for iPhone” means that an electronic accessory has been designed to
connect specifically to an iPhone® and has been certified by the developer to meet
Apple performance standards. Apple is not responsible for the operation of this
device or its compliance with safety and regulatory standards. Please note that the
use of this accessory with an iPhone® may affect wireless performance.
• iPhone, Lightning™ and all related marks and logos are trademarks of Apple Inc.,
registered in the U.S. and other countries.
Low Voltage Alert
A built-in alert is included to notify when the +12VDC supply voltage drops below
10 volts. If triggered, the unit will enter Safe Mode and mute audio output. A
warning will also display on-screen with instructions to turn the unit off until normal
operating voltage is restored.
1. Press and hold to access the System Settings: Main Menu.
2. Turn to Low Voltage Alert and press to enter.
3. Turn to select ON or OFF and press to enter.
Optional Remote Controller
Connecting an optional MMR-20 Wired Remote Controller (sold separately) will
add auxiliary control functionality from extended locations, such as separate audio
zones throughout a vessel. Up to three remotes may be connected to a single
MediaMaster® at a maximum distance of 75 ft. Remotes connect directly using
MediaMaster® controller cables and splitters (sold separately). Refer to the Owner’s
Manual supplied with the MMR-20 for specific installation and operation instructions.
Troubleshooting
Problem Possible Cause Possible Solution
Unit doesn’t
turn on
Faulty fuse Remove fuse and check with continuity meter.
Replace if necessary.
Poor connection integrity Check “Ground” and “+12VDC” connections for
pinched wires; ensure tight connections.
No or low sound
Mute is on Press to verify that Mute is not on.
Volume is turned down Rotate to adjust volume.
Amps not
turning on Poor connection integrity Check “Amp Turn-On” connections for pinched
wires; ensure tight connections.
No or poor
tuner reception Poor connection integrity Check antenna cable for pinched wires; ensure
tight connections.
USB connection
not working/
charging
Poor connection integrity Check USB cable for pinched wires; ensure tight
connections.
SiriusXM
Check Antenna A fault has been detected with
the SiriusXM antenna.
Ensure antenna cable is securely connected to the
SiriusXM Connect Vehicle Tuner.
Inspect the antenna cable for damage and kinks.
Replace the antenna if the cable is damaged.
SiriusXM products are available at your local audio
retailer or online at www.shop.siriusxm.com.
Check SXM Tuner
The radio is having diculty
communicating with the SiriusXM
Connect Vehicle Tuner.
Verify the SiriusXM Connect Tuner cable is
securely connected to the radio.
No Signal
The SiriusXM Connect Tuner is
having diculty receiving the
SiriusXM satellite signal.
Verify that your vehicle is outdoors with a clear
view of the sky. Verify that the SiriusXM antenna is
mounted securely to the outside of the vessel.
Remove obstructions above of next to the
SiriusXM antenna. Inspect antenna cable for
damage and kinks.
Consult the SiriusXM Connect Tuner installation
manual for more information on antenna
installation. Replace the antenna is the cable
is damaged. SiriusXM products are available at
your local audio retailer or online at www.shop.
siriusxm.com.
Subscription
Updated
The radio has detected a change
in your SiriusXM subscription
status. Press the BACK button to
clear the message.
Visit www.siriusxm.com or call 866-635-2349 in
the USA or 877-438-9677 in Canada if you have
questions about your subscription.
Channel Not
Available
The channel that you have requested
is not a valid SiriusXM channel or the
channel is no longer available. You may
also see this message briey when rst
connecting a new SiriusXM Connect
Tuner.
Visit www.siriusxm.com for more information
about the SiriusXM channel lineup.
Channel Not
Subscribed
The channel that you have requested is
not included in your SiriusXM subscrip-
tion package or the channel that you
were listening to is no longer included
in your SiriusXM subscription package.
Visit www.siriusxm.com or call 866-635-2349 in
the USA or 877-438-9677 in Canada if you have
questions about your subscription package or
would like to subscribe to this channel.
Channel Locked
The channel that you have
requested is Locked by the radio
Parental Control feature.
See page 10 for more information on the Parental
Control feature and how to access locked
channels.
Specifications
Electrical Specications
Operating Voltage 14.4V DC (10V – 15.9V allowable)
Maximum Current Draw 1.5 A
Standby Current Draw 120 mA
Fuse Value 5 A
Remote Turn-on Capacity 40 mA (max)
Operating Temp Range -4 F to +158 F (-20 C to +70 C)
Display
Size / Type 3.5-inch / TFT LCD backlighted
Resolution 320 x 240
Audio Outputs/Inputs
Output Channels 4 stereo pairs of RCA plugs (3 variable + 1 xed level)
Output Zones 1 main zone (variable), 2 assignable zones (variable)
and 1 xed level zone
Maximum Output Voltage 4V RMS (zones 1/2/3), selectable 4V/2V/1V RMS (zone 4)
Output Impedance 250 ohm
Input Channels 1 stereo pair of RCA plugs (2V/1V RMS input sensitivity)
Tuner
FM Tuner with RDS 87.5 MHz to 107.9 MHz (0.2 MHz step)
AM Tuner 530 kHz to 1710 kHz (10 kHz step)
NOAA Weather Band Tuner 162.400 MHz to 162.550 MHz (0.025 MHz step)
Favorites 18 presets across all tuners
Bluetooth®
Prole A2DP v1.2, AVRCP v1.4
Core Specication Version 2.1 + EDR
Codec SBC, aptX®
Connection Range Up to 35 ft / 11 m
USB
Interface USB 2.0 host
Maximum Current Output 1 A
Supported Audio Formats MP3, WAV, WMA
iPhone Compatibility 5, 5c, 5s, 6, 6+, 6s, 6s+ (all Lightning™ connector models)
Dimensions
Unit W x H x D 5.94 in. x 3.90 in. x 3.17 in. (151 mm x 99 mm x 80.5 mm)
Mounting Hole W x H 4.70 in. x 3.25 in. (119.50 mm x 82.50 mm)
Sirius XM Radio Inc. Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
The aptX® word mark and logos are registered trademarks owned by CSR.
iPhone® and Lightning™ are registered trademarks of Apple Inc.
Use of all trademarks by JL Audio is under license.
Version 4.0