JL Audio TRX-2 Wireless System User Manual TRX MAN REV1 indd

Download:
Mirror Download [FCC.gov]
Document ID	2552323
Application ID	+OJ9mAfyTZ7tC3ZdPZHQKg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	41.79kB (522345 bits)
Date Submitted	2015-03-11 00:00:00
Date Available	2015-03-12 00:00:00
Creation Date	2015-03-10 15:40:40
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2015-03-10 15:40:40
Document Title	TRX-MAN (REV1).indd
Document Creator	Adobe InDesign CC 2014 (Macintosh)

FCC Compliance Statement
NOTE: This equipment has been tested and found to comply with
the limits of Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-C
 onnect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
this equipment.
Wireless, High-Fidelity Audio Transmitter & Receiver System
TRX-MAN (REV1).indd 1
Safety Considerations
1. Read the Instructions – All safety and operating instructions should
be read before using this product.
2. Retain the Instructions – These instructions should be retained for
future reference.
3. Heed Warnings and Instructions – All warnings and instructions
should be followed.
4. Water and Moisture - This device should NOT be used near water,
such as a bathtub, washbowl, sink, laundry tub, in a wet basement,
near a swimming pool, etc.
5. Ventilation – While this device does not require specific ventilation
considerations, it should NOT interfere with ventilation of other
components.
6. Heat and Flames – This device should be situated away from heat
sources such as radiators, heat registers, stoves, fireplaces, or other
devices that produce heat.
7. Power Sources – Only used the supplied AC power adaptors to
power this product.
8. Power Cord Protection – Power supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit the device.
9. Cleaning – Clean only with a dry cloth. Unplug power cords from
wall outlet before cleaning.
10. N
 onuse Periods – The power adaptor cords should be unplugged
from the outlet when left unused for long periods of time.
11. L ightning and Power Surges – We recommend that you disconnect
the device from the electrical outlet during electrical storms and/or
recurring power interruptions.
12. O
 bject or Liquid Entry – Care should be taken so that objects
do not fall on and liquids are not spilled onto the device. Do not
expose the device to dripping or splashing from liquids. Do not
place objects filled with liquids on top of, or near the device, for
example: flower vases, beverages, liquid-filled lamps, etc.
13. O
 verloading – Do not overload wall outlets, extension cords, or
outlet strips as this can result in a risk of fire or electrical shock.
14. S ervicing - Do not attempt to service the device beyond what is
described in the operating instructions. All other servicing should
be referred to qualified personnel only.
Introduction
Thank you for purchasing a JLINK TRX wireless audio system. This
product has been critically engineered to deliver exceptional
performance in your audio system or home theater for many years to
come. Please read this manual thoroughly to correctly integrate and
achieve the highest level of performance.
What’s Included
(1) JLINK TX Transmitter
(1) JLINK RX Receiver
(2) AC Power Adaptors
(1) JLINK Port Connection Cable (3 ft.)
(1) Hook & Loop Fastener Tape
(1) User Manual
Product Overview & Features
The JLINK TRX system uses state-of-the-art wireless technology to send
audio signals up to 100 feet away (30 meters). Broadcasting at an ultrahigh frequency of 2.4 GHz, the JLINK TRX delivers crystal-clear, stereo
sound anywhere throughout your home.
Features include:
- Bit-Perfect PCM Stereo Digital Wireless Technology (16 bit / 48 kHz)
- RCA-type input/output connectors compatible with most audio
equipment
- Up to 4 JLINK receivers can be paired to each JLINK transmitter
(additional receivers sold separately)
- Up to 3 JLINK transmitters can be used concurrently (3 output
channels to choose from)
- JLINK receiver includes JLINK port for compatible JL Audio products
- Low-Power Sleep mode after 30 minutes of inactivity
Placement Considerations:
The transmitter and receiver modules may be situated in any position,
however their placement should be away from heat generating
sources, such as amplifier or receiver heat sinks. Also ensure that each
module’s placement does not interfere with the ventilation of other
components.
Although mounting is not necessary, you may use the supplied hook
& loop fastener tape to affix the modules to a flat surface on a cabinet
wall, rack or component. If you choose not to mount the modules,
make sure they are placed on a flat, stable surface to prevent damage
from falling.
Connecting the Transmitter
1. Select the source device that you wish to transmit audio signal from
and power OFF that device.
2. Connect the JLINK transmitter’s RCA line inputs to your source
device’s RCA line outputs.
3. Plug the smaller end of the AC power adaptor into the transmitter’s
power jack. Plug the larger end of the AC power adaptor into a
standard A/C wall outlet.
4. Using the bottom-mounted switch, select one of three output
channels to broadcast your audio signal. Note: The transmitter and
receiver need to be set to the same channel.
Connecting the Receiver – Option A
(when using RCA connections)
1. Select the device that you wish to send the audio signal to and
power OFF that device.
2. Connect the JLINK receiver’s RCA line outputs to your device’s RCA
line inputs.
3. Plug the smaller end of the AC power adaptor into the receiver’s
power jack. Plug the larger end of the AC power adaptor into a
standard A/C wall outlet.
4. Set the receiver’s bottom-mounted switch to the same channel as
the transmitter.
Connecting the Receiver – Option B
(when using JLINK port)
1. Select the JLINK compatible device that you wish to send the audio
signal to and power OFF that device.
2. Set the receiver’s bottom-mounted switch to the same channel as
the transmitter.
3. Plug one end of the supplied cable into the JLINK receiver’s JLINK
port. Plug the other end of the cable into the JLINK port of the
compatible device. The JLINK receiver will transfer its audio signal
and receive its power connection directly through this cable. Note:
When connected in this manner, the JLINK receiver’s AC power
jack and RCA output connections should NOT be used.
3/10/15 3:40 PM
LED Status Indicator
Specifications - System
A green LED light is located next to the power jack on the transmitter
and receiver to indicate each module’s status. Refer to the following
tables for its function and meaning.
LED Status - Transmitter
Action
LED Function
When first connected
3 rapid blinks, 1
to power
long blink, OFF
LED Function
3 rapid blinks,
OFF
Mode
Startup
LED Status - Receiver
Action
When first connected
to power
Begin RF link
Audio signal detected
ON
RF link established
No audio signal detected OFF
Standby
With RF link, no audio
signal detected
1 flash every 3
seconds
Standby
No audio signal for 30
minutes
Low Power Sleep*
With RF link, no audio
signal for 30 minutes
OFF
Low Power Sleep*
Audio signal detected
ON
OFF
Mode
*Transmitter will reawaken when audio is detected again.
Note: Plugging RCA cables in to the transmitter without a source
connected will cause LED on transmitter and receiver to turn ON.
Startup
*Receiver will reawaken when audio is detected again.
Specifications - Transmitter
S/N Ratio
80 dB @ 1 kHz, 500 mV
Inputs
THD+N
0.02% @ 1 kHz, 500 mV
Input Impedance
Crosstalk
>75 dB @ 1 kHz, 500 mV
Frequency Response
Wireless Range
Wireless Channels
Latency
Operating Temperature
AC Power Adaptor
Outputs
16 Hz – 22 kHz (+0, -1dB)
100 feet / 30 meters (typical)
3 available, selectable via switch
14 mS
32 to 104 °F / 0 to 40 °C
Receivers Supported
Bit Depth/Sample Rate
Power Requirements
Dimensions
Analog, left and right RCA-type
Inputs
25 kΩ
Bit-Perfect PCM Stereo Digital via
2.4 GHz Wireless
Up to 4
16 Bit / 48 kHz
200 mA, 5 volts (via AC adaptor)
3.5 in x 3.5 in x 1.12 in
89 mm x 89 mm x 28.5 mm
Limited Warranty / Service Information
Specifications - Receiver
Outputs
Output Impedance
Full Scale
Output Voltage
Power Requirements
1 A, 5 volts DC
Dimensions
Bit-Perfect PCM Stereo Digital via
2.4 GHz Wireless
Analog, left & right RCA-type or
Analog via JLINK port to compatible
product
250 Ω
1.2 V
100 mA, 5 volts (via AC adaptor or
JLINK port
3.5 in x 3.5 in x 1.12 in
89 mm x 89 mm x 28.5 mm
JL AUDIO warrants this product to be free of defects in materials
and workmanship for a period of three (3) years from the original date
of purchase.
Damage caused by the following is not covered under warranty:
accident, misuse, abuse, product modification or neglect, failure
to follow installation instructions, unauthorized repair attempts,
misrepresentations by the seller. This warranty does not cover
incidental or consequential damages and does not cover the cost of
removing or reinstalling the unit(s) or shipping the unit(s) to JL Audio
for service. Cosmetic damage due to accident or normal wear and
tear is not covered under warranty.
This warranty is not transferable and applies only to the original
purchaser of the product from an authorized JL AUDIO dealer.
Warranty is voided if the factory-applied product serial number is
removed or defaced.
Should service be necessary under this warranty for any reason
due to manufacturing defect or malfunction, JL AUDIO will, at its
discretion, repair or replace the defective product with new or
remanufactured product at no charge.
If you need service on your JL AUDIO product:
Any applicable implied warranties are limited in duration to the
period of the express warranty as provided herein beginning with
the date of the original purchase at retail, and no warranties, whether
express or implied, shall apply to this product thereafter. Some
states do not allow limitations on implied warranties, therefore these
exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from state
to state.
All warranty returns should be sent to JL AUDIO freight prepaid
through an authorized JL AUDIO dealer and must be accompanied by
proof of purchase (a copy of the original sales receipt.) Direct returns
from consumers or non-authorized dealers will be refused unless
specifically authorized by JL AUDIO with a valid return authorization
number. Warranty expiration on products returned without proof
of purchase will be determined from the manufacturing date code.
Coverage may be invalidated as this date is previous to purchase date.
Return only defective components. Non-defective items received
will be returned freight-collect. Customer is responsible for shipping
charges and insurance in sending the product to JL AUDIO. Freight
damage on returns is not covered under warranty. Always include
proof of purchase (sales receipt).
For Service Information in the U.S.A. please call:
JL Audio customer service:
(954) 443-1100 during normal business hours (Eastern Time)
JL Audio, Inc • 10369 North Commerce Parkway, Miramar, FL 33025
International Warranties:
Products purchased outside the United States of America are covered
only by that country’s distributor and not by JL Audio, Inc.
WARNING: THIS PRODUCT CONTAINS NO USER-SERVICEABLE PARTS.
PRODUCT IN WHICH DISASSEMBLY, REPAIR AND/OR MODIFICATION
HAS BEEN ATTEMPTED BY UNAUTHORIZED PARTIES WILL NOT BE
COVERED UNDER WARRANTY.
03-10-2015 Rev. 1 • Printed in China
TRX-MAN (REV1).indd 2
3/10/15 3:40 PM

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.6-c014 79.156797, 2014/08/20-09:53:02
Create Date                     : 2015:03:10 15:40:40-04:00
Metadata Date                   : 2015:03:10 15:40:40-04:00
Modify Date                     : 2015:03:10 15:40:40-04:00
Creator Tool                    : Adobe InDesign CC 2014 (Macintosh)
Instance ID                     : uuid:984b5d98-a669-b941-90a5-379fc6bca95a
Original Document ID            : xmp.did:de720314-34ad-4724-b3fa-c35307875724
Document ID                     : xmp.id:3de5ea72-02c6-4edd-b883-4f56309d432c
Rendition Class                 : proof:pdf
Version ID                      : 1
Derived From Instance ID        : xmp.iid:f077c718-987a-45dd-a600-c18a59cb6893
Derived From Document ID        : xmp.did:d940ba8e-c24c-4507-95f3-467249c1fb5a
Derived From Original Document ID: xmp.did:de720314-34ad-4724-b3fa-c35307875724
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2014 (Macintosh)
History Changed                 : /
History When                    : 2015:03:10 15:40:40-04:00
Format                          : application/pdf
Title                           : TRX-MAN (REV1).indd
Producer                        : Adobe PDF Library 11.0
Trapped                         : False
GTS PDFX Version                : PDF/X-1:2001
GTS PDFX Conformance            : PDF/X-1a:2001
Page Count                      : 2
Creator                         : Adobe InDesign CC 2014 (Macintosh)

EXIF Metadata provided by EXIF.tools