JSW Pacific CCD-401SA 2.4GHz Wireless Camera User Manual

JSW Pacific Corporation 2.4GHz Wireless Camera Users Manual

Users Manual

II-Navigator"User's ManualModel No.: CCD-401Miniature Wireless Color Camera System- Wireless Color Westherproof IP44 Camera withAudioPLEASE READ CAREFULLYAND SAVEThis manual contains important information about this product'soperation.If you are installing this product for use by others you must leave thismanual -or a copy- with the end user.
Model No.: CCD-4Q1Miniature Wireless Color Camera SystemImportant!Please read this booklet carefullybefore installing or using these units.DANGER-HIGHVOLTAGE-These unitsshould ONLY be opened by an authorizedtechnician if service is required.ContentsSafety PrecautionsFor correct and safe operation of thissystem, it is essential that installers, end-users and service technicians should followall safety procedures outlined in thismanual. Specific Warning and Cautionstatements (and/or symbols) are marked onthe units where needed.Warning and Caution Statements"WARNING" indicates a situation wherefailure to follow proper procedures cancause personal injury."CAUTION" indicates a situation wherefailure to follow proper procedures cancause damage to the equipment.Important Safety Precautions 1Specifications ..2Parts IncludedwithThis System ~.~ 3Parts of the Miniature Wireless Color CameraSystem :...... ..3- Parts ofthe Camera 3- Parts ofthe Receiver 3. Installation 4- Installing the Mounting Bracket(Camera Stand) 4- Installing and Aligningthe Cameraon the Mounting Bracket (Camera Stand) 4-Rotating the Camera 4-Installing the Miniature Wireless Color CameraSystem 5Troubleshooti n9 Guide 6Warranty 6
Important Safety PrecautionsPlease read before In$tallingyourpurd1~se of th~ MiniatureWireless ColorCameraIIinstructions beforeInstallin9and thiscamera,monitorand cordoutof reach c-Do not p'lac~thecamera,mollltor adaptercordin a alb or-Do 110tuse the camera near wat~r or damp and wet environments, sor wef basements,- locate camera, monitor and ACJDC adapt~r where th~re is ad~quat~ ventUation, Dothe camera in direct sunlight-Do nollocate the monitor and adapter near heal sou~s suCh as heal registers,radiators, ovens, or oth~r operating-Do with cords., Use only adapterolher may damage the camara or tmd'voidcomponents into standard voltage (110V -or 60 Hz),I cords from the ACIDC adapters, camera or monitor wherethey can pinched orProtect the cords them out of the of children, and routinetraffIC,Do not place with rugs or a-lJVhen cleaning, use a DRY, lint-free camera., monitor adaptercleaning, NEVER and do not spray solvents on theunit,Do.ingso maydamage or cause electrical shook.,-Unptug the ACIDC adapter from the wall outlet when Ihe i-Mishandling, alterations or modifications nol approved byPlease read IheselocateIsllotillUse,the warranty,A CAUTION!-Conned this unit ONLY to other compatiblounits, Do not connect it.10anyauxiliary devica, Connecting any1bing else to this unit may damage it orproperly.A CAUTION!- Do not paint over the camera,A CAUTIONI- This system uses public airwaves for wireless10 and pid<ed up by other 2,4 GHz recenear the camera may be broadcast andoff when not in use.Thesoundandvideomaybe broadcastConversationsand fromotherroomsTo protectyour privacy, turnthe cameraIMPORTANT!ACCESSORIES- Do not place video monitor or equipment on an unsteble cart, sland or tablo, The\/ideo monitor or equipment may fall causing serious injury to or adult, and serious damageto the equipment Wall or shelf mounting should follow the manufacturer's instruction, and shoulduse a mounting kit approved by the manufacturer.Video monitor equipment and cart combinations should be moved wilh care,Quickstops, exce$$iveforca, and uneven surfaces .may cause the equipment and cartcombination to overturn,VENTILATION- Slots and openings in the cabinet and the bad< or bottom are provided for ventilationand to ensure reliablo operation of the video monitor or equipment amBo protect it from overheating.These openings mUst not be blod<ed or covered. The openings should never be blod<ed by placingthe video monitor on a bed, sofa, rug, or other similar surface. Video monitor or equipment receiver,should never be placed near or over a radiator or heat register. Video monitor or equipment recoivershouid not be placed in a built-in installation such as a bookcase unless proper ventilation is provided.(i)FCC/CE WARNINGThis equipment generates and uses radiothat is, inSlrict accordance with the manu:television reception, It has been tested and found to comply with for aaccordance with p.art 15 of FCC Rules and CE t-ETS 300 <MO. are dfreasonable protection against such interferenca in a residential installation,at interference will not occur ina particular installation, If eIto radio or television reception, which can be turning the equipment offand on. the user is encouraged to try to correct the interference by one or more of Ihe followingmeasures:1, Reorient the TV/radio antenna,2, Relocate the Receiver away !rom the TV/radio receiver,3. Plug the Receiver into a different wall outlet so that the Receiver is on a branCh circuit.4, If necessary, the user should consult the dealer or an experienced radio/television techniCian foradditional suggestions,The user may find the following booklet prepared by the Federal Communication Commissi()n helpful:"How to Identify and Resolve TV Interference Problems,' This booklet is from the USGovernment Pnnting Office. Washington, D,C, 20402, Stock No,FCCICE NOTICEThe user Is cilutioned that changes or modifications notcould void the user's authorttyto operate the equipmentcommunications link and fill an Important need In portable wireless signaling,some limitations which must be obsefl/ed,The radios are required. to comply wilh FCC Rules and300440, As such, they have limited transmitter power,respondto morethan.onetransmittedsignalat:ll time and mayoner near Iheir operating frequenclos, Changes or modifications to the device mayInfrequently used radio links should be tested regularty to protect againstor faultSpecificationsthe manufacturera reliablethere areCEIMAGE SENSOR 113" CoiorCMOS Il'Ntge SensorRESOLUTrON 330 Homontal TV Une~LENS 6mmPOWERCONSUMPTION1.5 V DC, 300 mA1 ,:) V\lall$ILLUMINATION < 6 lllX with IR al F2,O meter)OPERATING TEMP. 32"F . 122"F O'C - SO'CDIMENSIONS Approx. 4,5-" 2.a- x 2,4"HAy;. 1,3 x Gem (l.xWxH)WEiGHT Appro", OA6LBJ200g
Pans Included with This System-Camera with Built-In Transmitter- 2.4 GI-btAudioNldeo Receiver-12V ACJDC Adapter for the Receiver- 1.5V300 RIA Adapter for the Camera-1,5mAN ~ble""Parts of the Miniature Wireless Color Camera SystemParts of the Camera1.Camers Lens2. 12 p<:$IR LED3.Antenna4. PowerJack5. Camera Stand6. IR Auto Control for Night Vision7. Mlcrophf)ne8. Channel Switch253874InstallationToolsyou will need: Pencil,Drill, Drill Bits, Phillips.headScrewdriver. Hammer{Installing Mounting Bracket (Camera Stand)1. Select a mounting location. Use the mounting bracket asa guide and mark the screw holeswith a pencil.2. Align the bracket over the holes or wall anchors and tightenthe screws to secure the bracket to the wall or ceiUng.Installing and Aligning the Camera on theMounting Bracket (Camera Stand)1. Slide the camera into the camera holder,2. Lineup mountingholesof the camera holderandthe bracket.3. Insertthumb screw,adjust camera10desired angleand tighten screw.Rotating the CameraLoosen up the Thumb Screw and adjust the camera 10desired angle. then lighten the screw.,cr~."""'-".'/'"..,','.' <,.""-,-.,/if ~Attach Stand toMounting Surface
Installing the Miniature Wireless Color Camera SystemToinstallthe system, follow these steps:Receiver:1. Plug the AC/DC adapter cord into the DC input jack on the back ofthe receiver.2. Plug the audlolvldeo cord to the anulo!v1deo output jack of the receiver. Plug the other end of theto the audiolv1deo input jacks on your TV or monitor.3. Plugthe nv ACIDC adapter Inlo a(110V-.240V) outlet The power indicator LEDlocated on the top of the reoelverCamera:1. Plug the 7.5VAcmc adapter cord into Ihe DC input jack on the back of the camera.2. Plug the adapter inlo a standard (110V-240V) AC outletSystem Setup:1.Selectthe channel(Channel1'-4) 10 be used onboththe cameraand receiver.NOTE: Make sure the camera and receiver are set to the same channel (1, 2,3 or 4).2. Set the selected channel by gently pushing the dip-switch for that channel 10the ON position onboth the camera and the receiver.For example, to set both the camera and receiver on 1:(a) Push the Channel 1 dip-switch located on the bottom l.'1]the camera and the receiver to the ON position. 1 ;1 34(b) Make sure the remaining dip-switches are In the OFF Carn Set 10position. In this case, channels 2, 3 and 4 should be In Chan~:'1the OFF position.Ifmore than one camera is to be installed and operated at the same time:Simply follow steps (a) and (b) and set thedip-switches for the other channels on thecamera and receiver to ON.For example, to operate two cameras: setCamera 1 to Channel 1 (other channels off) Camera1 Camera2, Set to Set tosetCamera 2 to Channel 2 (other channels off), Channel 1 Channa! 2£1110on the rflceiller, set channels 1 and2 to ON.See "Camera and Receiver Selting Chart" below for more detailed Instructions.3. Position the camera antenna toward the receiver antenna. Rotate/adjust the antennas on both thecamera and receiver for best performance.Additional Notice- When installing the camera, check the reception of the receiver before finalinstallation. Have someone hold the camera in the area to be monitored and another person to checkthe receptionWithyourTV or monitor. If interferenceor other problemsC)CCUr,refer to theTroubleshooting Guide.1.-. i III1;13 .. ['jJ III1 2 3 4 1 ;1 :I 4ReceiverSetto Channel1&2Camera & Receiver Channel Setting Chart1. This 2,4 GHz system can be connected with up to "channels. Set channels on the camera and receiverbefore starting the system.2. Set camera and receiver channels by gently pushing theswitches Withan object such as a pen ar pencil to the ONor OFF position. Use the illustrations shown on !he rightas a guide. The switches are inset into the camera andreceiver housings to avoid accidentally changing thechannel settings.3. The Auto Sequential Scann."!; foOllure automaticallyactivates when more than one switch is set to' ON.Camera 1 Camera3CH1 Ii ! Iii 11CH312 3 4Camera 2 Camera 41/:.i,H CH2 II I I -, CH41234 1234ReceiverONTroubleshooting GuideON1 Year Limited Warranty:JSN'oIPacific Corp., !he meker of Navigator. brand products, warrants that for a pariodof 1 year fromthe date of purchase, this product will be free from defects in material and workmanship. JSW, at itsoption, will repair or replace this product or any component of the product found to be defective duringthe warranty period. Replacement will be made with a new or remanufactured product or component.If the product is no longer available,replacemern may be made with a similar product of equal orgreater value. This is your exclusive warranty. This warranty is valid for the original purchaser from thedate of initial purchase With JSW and is not transferable. This warranty does not cover norma! wear ofparts or damage resulting from any of the following: negligent use or misuse of the product, use onimproper voltage or current, use contrary to the operating instructions, disassembly, repair or alterationby anyone other than JSW or an authorized service center. Further, the warranty does not cover ac!$of God, such as lire, 110od, hurricanes and tomadoes or any batteries that are induded withthis unitJSW shall not be liable for any incidental or consequential damages caused by the breach of anyexpress or implied warranty.If the Cameraand/or Manitor... IYou should... iNo Power 1. Check that the power cord(s) Is properly connected.2, Checkthatthe monitar is turned ON.3. Wrong ACIDC adaotar used. Check Ihat the adapter labeledOUTPUT: 7.5Vt)C. is connected 10the w;I\:fL. and adapterlabeled OUTPUT:'51/DC is connected to thecamcrnNo sound or picture. 1. Check the channel switch settings on the camera(s) andDistorted sound or monitor. Make sure the channels match on both units.picture 2. SIgnal interference from a microwave oven. Check if amicro-wave oven is in use Orlocated in the path betweenthe camera and monitor. If so, tum it off or move it aut ofthe path.3. Signal interference from other signal producing devices.(a) Change the channel setllng on both camera and monitor.(b) Identify and eliminate the source of the inlerference.(0) Relocate the camera and/or monitor closer 10 eacholher.4. Camera and monitor are too far apart. Relacate the cameraand/or monitor5. Antennais positioned improperly. Adjust the antenna on thecamera and/of monitor.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician for help. FCC Caution :To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Navigation menu