JVC KENWOOD 371302 VHF Digital base repeater User Manual B62 1994 00 NXR 700 800 indd

JVC KENWOOD Corporation VHF Digital base repeater B62 1994 00 NXR 700 800 indd

Instruction Manual

Download: JVC KENWOOD 371302 VHF Digital base repeater User Manual B62 1994 00 NXR 700 800 indd
Mirror Download [FCC.gov]JVC KENWOOD 371302 VHF Digital base repeater User Manual B62 1994 00 NXR 700 800 indd
Document ID809631
Application IDHt4sMywjlUMnhlXmeFzJbg==
Document DescriptionInstruction Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize53.27kB (665843 bits)
Date Submitted2007-06-29 00:00:00
Date Available2007-06-29 00:00:00
Creation Date2007-04-25 11:27:02
Producing SoftwareAdobe PDF Library 7.0
Document Lastmod2007-04-25 14:40:14
Document TitleB62-1994-00_NXR-700-800.indd
Document CreatorAdobe InDesign CS2_J (4.0)

NXR-700/ NXR-800
VHF DIGITAL BASE-REPEATER/ UHF DIGITAL BASE-REPEATER
INSTRUCTION MANUAL
BASE-REPETIDOR DIGITAL VHF / BASE-REPETIDOR DIGITAL UHF
MANUAL DE INSTRUCCTIONES
BASE-RELAIS NUMÉRIQUE VHF/BASE-RELAIS NUMERIQUE UHF
MODE D'EMPLOI
© B62-1994-00 (K, K2)
09 08 07 06 05 04 03 02 01 00
NXR-700 / NXR-800 INSTRUCTION MANUAL
VHF DIGITAL BASE-REPEATER / UHF DIGITAL BASE-REPEATER
THANK YOU!
We are grateful you purchased this Kenwood repeater.  We
believe this easy-to-program repeater will be highly effective in
your communications system, and will keep personnel operating
at peak efficiency.
Kenwood incorporates the latest in advanced technology into
all of our products.  As a result, we feel strongly that you will be
pleased with the quality and features of this product.
◆ This repeater is intended for use as a fixed base station with the
antenna located outdoors on the rooftop or on an antenna tower.
◆ Use only the supplied DC cord.
◆ Do not remove the ferrite core attached to the DC cord. Doing so
may cause interference with radio communications.
UNPACKING AND CHECKING EQUIPMENT
PRECAUTIONS
•
•
•
•
•
Do not expose the unit to rain or moisture; to prevent fire or
electric shock.
Do not open the unit under any circumstances; to avoid risk
of electric shock.
Do not expose the unit to long periods of direct sunlight, nor
place it close to heating appliances.
Do not place the unit in excessively dusty and/or humid
areas, nor on unstable surfaces.
If you detect an abnormal odor or smoke coming from the
unit, disconnect the power from the unit immediately.  Contact
your Kenwood service center or dealer.
NOTICES TO THE USER
FCC WARNING
This equipment generates or uses radio frequency energy.  Changes
or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction
manual.  The user could lose the authority to operate this equipment if
an unauthorized change or modification is made.
Note:  The following unpacking information is for use by your
Kenwood dealer, an authorized Kenwood service center, or the
factory.
Carefully unpack the repeater.  We recommend that you
identify the items listed in the following table before discarding
the packing material.  If any items are missing or have
been damaged during shipment, file a claim with the carrier
immediately.
Item
Front glass
Dressed screw
Bracket
Flat head machine screw
Handle and screw set
DC cord
Lead wire with connector (15 pin)
Fuse (7.5 A)
Instruction Manual
Serial number sticker
Part Number
B10-2781-XX
N08-0563-XX
J29-0725-XX
N32-4008-XX
K01-0421-XX
E30-3344-XX
E37-1381-XX
F05-7521-XX
B62-1994-XX
B42-7325-XX
Quantity
INSTALLATION
◆ Government law prohibits the operation of unlicensed radio
transmitters within the territories under government control.
◆ Illegal operation is punishable by fine and/or imprisonment.
◆ Refer service to qualified technicians only.
To install the handles onto the front panel of the repeater, align
the handles with the holes on the front panel, then secure the
handles using the supplied screws.
Please consult your dealer for installing the repeater and
antenna.
MICROPHONE
Connect an optional KMC-30, KMC-35, or KMC-9C Kenwood
microphone to the MICROPHONE jack on the front panel.
CONTROLS AND FUNCTIONS
■ Front Panel
STATUS
1 2 3 4 5 6 7 8
CTRL
OCXO
BUSY
TX
POWER
VOLUME
TAKE RPT
MON OVER
DISABLE
COM
OFF/
MICROPHONE
!2 !1 !0 o i
q Speaker
w CH/STATUS Display
Two 17-segment digits display the channel number,
name, or status.
e STATUS indicator
Indicates the status of the repeater.
r Programmable Function keys
Press these keys to activate their programmable
functions.
t COM jack
Connect to PC. Conform to RS-232C standard.
y VOLUME control
Turn clockwise until a clicksounds, to unmute the volume.
Rotate to adjust the volume. Turn counterclockwise fully
to mute the volume.
u MICROPHONE jack
Connect a microphone to this 8-pin modular jack.
Lights red when no reference signal is available or when
an error occurs.
Does not light when the reference signal is an internal
VCXO signal.
!2 CTRL indicator
The CTRL indicator shows the RCCH status while using
Digital trunking :
Lights Green when the repeater is used as RCCH.
Blinks Green when using a non-dedicated channel, and
RCCH is used as RDCH.
Does not light when using RDCH.
i POWER indicator
Lights green when power is supplied to the DC 13.8V
jack. Blinks when an abnormal voltage is present.
o TX indicator
Lights red while transmitting.
!0 BUSY indicator
Lights green while a signal is being received.
!1 OCXO indicator
The OCXO indicator shows the state of the reference
10 MHz oscillator :
Lights Green when using a reference signal from an
optional OCXO unit.
Lights Orange when using a reference signal from another
repeater.
■ Rear Panel
TEST/SPKR
CONTROL I/O
SYNC
LAN
REF OUT
REF IN
FUSE
DC 13.8V
⑩
75
RX
q RX IN jack
Connect an RX antenna or a duplexer to this BNC
receptacle.
w TEST/SPKR jack
Test input/output jack.  Connect an external speaker to
this jack.
e CONTROL I/O jack
Connect an repeater controller to this DB‑25 interface.
r SYNC 1/2 jack
Connect to other repeater to use synchronous frame
signal.
t LAN jack
Connect to Ethernet.
TX
y REF OUT jack
Connect to another repeater within the site to supply a
reference signal.
REF
IN jack
Connect from another repeater within the site to receive a
reference signal.
i FUSE
Insert 7.5 A blade fuses into these fuse holders.
o DC 13.8V jack
Connect a 13.8 V DC power supply to this jack.
⑩ TX OUT jack
Connect a TX antenna or a duplexer to this receptacle.
REPEATER OPERATION
Note:Please consult your dealer for programming the repeater.
Whe operating the repeater using an optional OCXO unit, allow the
unit to warm up for 24 hours after turning the power on.
When power is applied to the unit, the POWER indicator lights
green.
Turn the VOLUME control clockwise until a click sounds, to
unmute the volume. Rotate to adjust the volume. Turn the
VOLUME control counterclockwise fully to mute the volume
The BUSY indicator lights green while receiving a signal and the
TX indicator lights red while transmitting.
TRANSCEIVER OPERATION
■ Receive
Adjust the volume to your desired level.  You may need to
readjust the volume when you receive a message from your
dispatcher or another member in your fleet.
• The BUSY indicator lights green while a signal is being
received.
■ Transmit
1 Listen to the channel before transmitting, to make sure it
is not being used.
2 Press the microphone PTT switch, then speak in your
normal speaking voice.
• The TX indicator lights red while transmitting.
3 When you finish speaking, release the PTT switch.
UNITE OCXO
UNIDAD OCXO
KXK-3
KXK-3
MODE D'EMPLOI
MANUAL DE INSTRUCCTIONES
INSTRUCTION MANUAL
KXK-3
OCXO UNIT
© B62-2022-00 (M)
09 08 07 06 05 04 03 02 01 00
PRECAUTIONS
		•		Do not drop the unit.
		•		Aviod jarring the unit, causing vibrations or strong impacts.
• Do not expose the unit to rain or moisture; to prevent fire or electric shock.
• Do not open the unit under any circumstances; to avoid risk of electric shock.
• Do not expose the unit to long periods of direct sunlight, nor place it close to heating appliances.
• Do not place the unit in excessively dusty and/or humid areas, nor on unstable surfaces.
NOTICES TO THE USER
This device complies with Part 15 of the FCC Rules.  Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
One or more of the following statements may be applicable to this equipment.
FCC WARNING
This equipment generates or uses radio frequency energy.  Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the
instruction manual.  The user could lose the authority to operate this equipment if an unauthorized
change or modification is made.
◆ Government law prohibits the operation of unlicensed radio transmitters within the territories
under government control.
◆ Illegal operation is punishable by fine and/or imprisonment.
◆ Refer service to qualified technicians only.
UNPACKING AND CHECKING EQUIPMENT
Note:  The following unpacking information is for use by your Kenwood dealer, an authorized Kenwood service center, or the factory.
Carefully unpack the unit.  We recommend that you identify the items listed in the following
table before discarding the packing material.  If any items are missing or have been
damaged during shipment, file a claim with the carrier immediately.
Item
Panhead sems screw W
Flat cable
Lead wire with mini pin plug
Lead wire with connector
Instruction Manual
Part Number
N67-3008-XX
E37-1405-XX
E31-3269-XX
E37-1406-XX
B62-2022-XX
Quantity
INSTALLATION
Please consult your dealer for installing the OCXO unit.
Note:   When installing the OCXO unit, be sure to note the direction of the unit.
Authorized Representative:
Kenwood Electronics Europe B.V
Amsterdamseweg 37, 1422 AC Uithoorn, Netherlants
MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS
• Use only manufacturer or dealer supplied antenna.
• Antenna Minimum Safe Distance: 60 cm (2 feet), 50% duty Cycle.
• Antenna Gain: 0 dBd referenced to a dipole.
The Federal Communications Commission has adopted a safety standard for human
exposure to RF (Radio Frequency) energy which is below the OSHA (Occupational Safety
and Health Act) limits.
• Antenna Mounting: The antenna supplied by the manufacturer or radio dealer must not be
mounted at a location such that during radio transmission, any person or persons can
come closer than the above indicated minimum safe distance to the antenna, i.e. 60 cm
(2 feet) , 50% duty Cycle.
• To comply with current FCC RF Exposure limits, the antenna must be installed at or
exceeding the minimum safe distance shown above, and in accordance with the
requirements of the antenna manufacturer or supplier.
• Vehicle installation: The antenna can be mounted at the center of a vehicle metal roof or
trunk lid, if the minimum safe distance is observed.
• Base Station Installation: The antenna should be fixed-mounted on an outdoor permanent
structure. RF Exposure compliance must be addressed at the time of installation.
Antenna substitution: Do not substitute any antenna for the one supplied or recommended
by the manufacturer or radio dealer.
You may be exposing person or persons to excess radio frequency radiation. You may
contact your radio dealer or the manufacturer for further instructions.
Maintain a separation distance from the antenna to person(s) of at least
60 cm (2 feet) , 50% duty Cycle.
You, as the qualified end-user of this radio device must control the exposure conditions of
bystanders to ensure the minimum separation distance (above) is maintained between the
antenna and nearby persons for satisfying RF Exposure compliance. The operation of this
transmitter must satisfy the requirements of Occupational/Controlled Exposure
Environment, for work-related use, transmit only when person(s) are at least the minimum
distance from the properly installed, externally mounted antenna. Transmit only when
people outside the vehicle are at least the recommended minimum lateral distance away
from the antenna/vehicle

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-702
Instance ID                     : uuid:aa1da2eb-a88b-43f5-b88d-49b30ea9e3ab
Document ID                     : adobe:docid:indd:8a85e9da-e076-11db-bc92-db7be0d0fa05
Rendition Class                 : proof:pdf
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:33a289e2-de8e-11db-86c7-0017f20495a0, uuid:837b8c53-de9b-11db-86c7-0017f20495a0, uuid:7a0cd5b5-e635-11db-b9aa-0017f20495a0, uuid:ac77d33c-e635-11db-b9aa-0017f20495a0, uuid:33a289e2-de8e-11db-86c7-0017f20495a0
Manifest Reference Document ID  : uuid:F5F28055E06B11DB9216FAA4D6859FC8, uuid:F5F28059E06B11DB9216FAA4D6859FC8, uuid:B5C62701E29C11DBAA94CE7A41EDEBD6, uuid:0E0A2BA3D89011DBB9B1F5FFB8A959D7, uuid:F5F28055E06B11DB9216FAA4D6859FC8
Create Date                     : 2007:04:25 11:27:02+09:00
Modify Date                     : 2007:04:25 14:40:14+09:00
Metadata Date                   : 2007:04:25 14:40:14+09:00
Creator Tool                    : Adobe InDesign CS2_J (4.0)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 7871 bytes, use -b option to extract)
Format                          : application/pdf
Title                           : B62-1994-00_NXR-700-800.indd
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
GTS PDFX Version                : PDF/X-1:2001
GTS PDFX Conformance            : PDF/X-1a:2001
Page Count                      : 6
Creator                         : Adobe InDesign CS2_J (4.0)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: K44371302

Navigation menu