JVC KENWOOD 371310 VHF Transmitter User Manual

JVC KENWOOD Corporation VHF Transmitter Users Manual

Contents

Users Manual

Download: JVC KENWOOD 371310 VHF Transmitter User Manual
Mirror Download [FCC.gov]JVC KENWOOD 371310 VHF Transmitter User Manual
Document ID1478597
Application ID0g98L29bLr2DDPsdQXU2bA==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize37.6kB (469975 bits)
Date Submitted2011-06-07 00:00:00
Date Available2011-06-17 00:00:00
Creation Date2017-11-05 09:18:25
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-11-05 09:18:25
Document TitleUsers Manual
Document CreatorAdobe InDesign CS2_J (4.0.5)

NXR-700/ NXR-800
VHF DIGITAL BASE-REPEATER/ UHF DIGITAL BASE-REPEATER
INSTRUCTION MANUAL
BASE-RELAIS NUMÉRIQUE VHF/ BASE-RELAIS NUMÉRIQUE UHF
MODE D'EMPLOI
BASE-REPETIDOR DIGITAL VHF / BASE-REPETIDOR DIGITAL UHF
MANUAL DE INSTRUCCTIONES
BASE-RIPETITORE DIGITALE VHF/ BASE-RIPETITORE DIGITALE UHF
MANUALE DI ISUTRUZIONI
VHF DIGITAL BASE-REPEATER/ UHF DIGITAL BASE-REPEATER
BEDIENUNGSANLEITUNG
VHF DIGITALE BASIS REPEATER/ UHF DIGITALE BASIS REPEATER
GEBRUIKSAANWIJZING
© B62-XXXX-00 (E)
09 08 07 06 05 04 03 02 01 00
NXR-700 / NXR-800 INSTRUCTION MANUAL
VHF DIGITAL BASE-REPEATER / UHF DIGITAL BASE-REPEATER
THANK YOU!
UNPACKING AND CHECKING EQUIPMENT
We are grateful you purchased this Kenwood repeater. We
believe this easy-to-program repeater will be highly effective in
your communications system, and will keep personnel operating
at peak eficiency.
Kenwood incorporates the latest in advanced technology into
all of our products. As a result, we feel strongly that you will be
pleased with the quality and features of this product.
Note: The following unpacking information is for use by your
Kenwood dealer, an authorized Kenwood service center, or the
factory.
Carefully unpack the repeater. We recommend that you identify
the items listed in the following table before discarding the
packing material. If any items are missing or have been damaged
during shipment, ile a claim with the carrier immediately.
Item
PRECAUTIONS
•
•
•
•
•
Front glass
Dressed screw
Bracket
Flat head machine screw
Handle and screw set
DC cord
Lead wire with connector (15 pin)
Fuse (15 A)
Instruction Manual
Do not expose the unit to rain or moisture; to prevent ire or
electric shock.
Do not open the unit under any circumstances; to avoid risk
of electric shock.
Do not expose the unit to long periods of direct sunlight, nor
place it close to heating appliances.
Do not place the unit in excessively dusty and/or humid
areas, nor on unstable surfaces.
If you detect an abnormal odor or smoke coming from the
unit, disconnect the power from the unit immediately. Contact
your Kenwood service center or dealer.
Part Number
Quantity
B10-2781-XX
N08-0563-XX
J29-0725-XX
N32-4008-XX
K01-0421-XX
E30-3344-XX
E37-1381-XX
F05-1537-XX
B62-XXXX-XX
INSTALLATION
To install the handles onto the front panel of the repeater, align
the handles with the holes on the front panel, then secure the
handles using the supplied screws.
Please consult your dealer for installing the repeater and
antenna.
NOTICES TO THE USER
◆ Government law prohibits the operation of unlicensed radio
transmitters within the territories under government control.
◆ Illegal operation is punishable by ine and/or imprisonment.
◆ Refer service to qualiied technicians only.
MICROPHONE
Connect an optional KMC-30, KMC-35, or KMC-9C Kenwood
microphone to the MICROPHONE jack on the front panel.
OCXO UNIT (KXK-3):Option
◆ This repeater is intended for use as a ixed base station with
the antenna located outdoors on the rooftop or on an antenna
tower. (except U.S.A. and Canada)
◆ This repeater is designed for a 13.2 V DC power source!
Never use a 24 V DC or higher source to power the repeater.
◆ Use only the supplied DC cord.
◆ Do not remove the ferrite core attached to the DC cord. Doing
so may cause interference with radio communications.
The OCXO unit (KXK-3) is an Oven Controlled Crystal Oscillator
(OCXO) unit.
The AMBE+2 voice coding Technology embodied in this product
is protected by intellectual property rights including patent rights,
copyrights and trade secrets of Digital Voice Systems, Inc. This voice
coding Technology is licensed solely for use within this Communications
Equipment. The user of this Technology is explicitly prohibited from
attempting to extract, remove, decompile, reverse engineer, or
disassemble the Object Code, or in any other way convert the Object
Code into a human-readable form. U.S. Patent Nos. #5,870,405,
#5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050,
#5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084
and #5,195,166.
CONTROLS AND FUNCTIONS
■ Front Panel
STATUS
1 2 3 4 5 6 7 8
VOLUME
TAKE RPT
MON OVER
DISABLE
CTRL
OCXO
BUSY
TX
POWER
COM
!2 !1 !0 o i
q Speaker
w CH/STATUS Display
Two 17-segment digits display the channel number, name,
or status.
e STATUS indicator
Indicates the status of the repeater. (NXDN mode)
r Programmable Function keys
Press these keys to activate their programmable
functions.
t COM jack
Connect to the PC using a RS-232C standard DB9
(Female) cross cable.
y VOLUME control
Turn clockwise until a click sounds, to unmute the audio.
Rotate to adjust the audio. Turn counterclockwise fully to
mute the audio.
u MICROPHONE jack
Connect a microphone to this 8-pin modular jack.
POWER
indicator
Lights green when power is supplied to the DC 13.2V
jack. Blinks red when an abnormal voltage is present.
■ Rear Panel
TEST/SPKR
CONTROL I/O
SYNC
LAN
REF OUT
OFF/
MICROPHONE
While blinking, the repeater cannot be used.
o TX indicator
Lights red while transmitting.
!0 BUSY indicator
Lights green while a signal is being received.
!1 OCXO indicator
The OCXO indicator shows the state of the reference
10 MHz oscillator :
Lights Green when using a reference signal from an
optional OCXO unit (KXK-3).
Lights Orange when using a reference signal from another
repeater.
Lights red when no reference signal is available or when
an error occurs.
Does not light when the reference signal is an internal
VCXO signal.
!2 CTRL indicator
The CTRL indicator shows the control channel status
while using Digital trunking :
Lights Green when the repeater is used as control channel.
Blinks Green when using a non-dedicated control channel.
FUSE
DC 13.2V
⑩
REF IN
15
RX
TX
FUSE 15A
q RX IN jack
Connect an RX antenna or a duplexer to this BNC
receptacle.
w TEST/SPKR jack
Test input/output jack. Connect an external speaker to
this jack.
e CONTROL I/O jack
Connect a repeater controller or a remote panel to this
DB-25 interface.
r SYNC 1 / 2 jack
Connect to another repeater to use synchronous frame
signaling for digital trunking.
t LAN jack
Connect to Ethernet.
y REF OUT jack
Connect to another repeater within the site to supply a
reference signal.
u REF IN jack
Connect from another repeater within the site to receive a
reference signal.
i FUSE
Insert 15 A blade fuse into this fuse holder.
o DC 13.2V jack
Connect a 13.2 V DC power supply to this jack.
⑩ TX OUT jack
Connect a TX antenna or a duplexer to this BNC receptacle.
TRANSCEIVER OPERATION
REPEATER OPERATION
■ Receive
Note: Please consult your dealer for programming the repeater. Due
to the frequency stability on the 6.25 kHz bandwidth channel, when
operating the repeater using an optional OCXO unit, allow the unit to
warm up for 24 hours after turning the power on.
After turning on the power, wait for approximately 10 seconds for
the VCXO or 5 minutes for the OCXO (when mounting) to warm up.
During this time, the CH/STATUS Display will blink. The keys will
function when they are pressed.
Adjust the volume to your desired level. You may need to
readjust the volume if you are having interference while
receiving a message from your dispatcher or another member
in your leet.
The BUSY indicator lights green while a signal is being
received.
When power is applied to the unit, the POWER indicator lights
green. Turn the VOLUME control clockwise until a click sounds,
to unmute the audio. Rotate to adjust the audio. Turn the
VOLUME control counterclockwise fully to mute the audio.
The BUSY indicator lights green while receiving a signal and the
TX indicator lights red while transmitting.
■ Transmit
1 Listen to the channel before transmitting, to make sure it
is not being used.
2 Press the microphone PTT switch, then speak in your
normal speaking voice.
The TX indicator lights red while transmitting.
3 When you inish speaking, release the PTT switch.
NOTIFICATION
This equipment complies with the essential requirements of
Directive 1999/5/EC.
The use of the warning symbol
means the equipment is subject
to restrictions of use in certain countries.
This equipment requires a licence and is intended for use in the
countries as below.
NOTIFICATION
Cet équipement est conforme aux principales exigences de la
Directive 1999/5/CE.
signiie que l’équipement
L’usage du symbole d’avertissement
est soumis à des restrictions d’usage dans certains pays.
Cet équipement nécessite un contrat de licence et il est destiné à
être utilisé dans les pays ci-dessous.
AVISO
Este equipo cumple con los requisitos esenciales de la Directiva
1999/5/CE.
El uso del símbolo de advertencia
signiica que el equipo está
sujeto a restricciones de uso en ciertos países.
Este equipo requiere una licencia y está destinado para utilizarse
en los siguientes países.
AT
IE
SE
LT
BE
IT
CH
MT
DK
LI
GB
PL
FI
LU
CY
SK
FR
NL
CZ
SI
DE
NO
EE
BG
GR
PT
HU
RO
IS
ES
LV
ISO3166
AVVISO
La presente apparecchiatura è conforme ai requisiti fondamentali della
Direttiva 1999/5/CE.
L’uso del simbolo di avvertenza
indica che l’apparecchiatura è
soggetta alle limitazioni d’uso in vigore in determinati paesi.
Questa apparecchiatura e’concepita per essere utilizzata in tutti
L’apparecchiatura deve essere provvista di licenza e n’è consentito
l'uso nei seguenti paesi.
HINWEIS
Dieses Gerät erfüllt die grundlegenden Anforderungen der Direktive
1999/5/EG.
be-deutet, dass dieses Gerät in manchen Ländern
Das Alert-Zeichen
bestimmten Verwendung-seinschränkungen unterliegt.
Für dieses Gerät ist eine Lizenz erforderlich; es ist für die Verwendung
in den unten aufgeführten Ländern vorgesehen.
KENNISGEVING
Deze apparatuur voldoet aan de vereisten van Richtlijn 1999/5/EG.
Het gebruik van het waarschuwings-symbool
betekent dat dit apparaat
in bepaalde landen aan gebruiksbe-perkingen onderhevig is.
Voor deze apparatuur is een licentie nodig en is bedoeld voor gebruik
in onderstaande landen.
AT
BE
DK
FI
FR
DE
GR
IS
IE
IT
LI
LU
NL
NO
PT
ES
SE
CH
GB
CY
CZ
EE
HU
LV
LT
MT
PL
SK
SI
BG
RO
ISO3166
One or more of the following statements may be applicable:
FCC WARNING
This equipment generates or uses radio frequency energy.
Changes or modiications to this equipment may cause harmful
interference unless the modiications are expressly approved
in the instruction manual. The user could lose the authority to
operate this equipment if an unauthorized change or modiication
is made.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED
BY THE FCC
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation.
This equipment generates, uses and can generate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment to an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer for technical assistance.
B59-2669-00
Addendum
Terminal Description
Control I/O (D-SUB 25 Pin) CONNECTOR
MIC (Modular Jack)
Pin
NO.
Pin Name
NC
Description
Specification
I/O
Notes
Pin
NO.
Pin Name
Description
Specification
I/O
Not used
Not used
−
NC
Not used
Not used
−
Notes
SB
Power Output
13.8 V
NC
Not used
Not used
−
GND
GND
GND
−
NC
Not used
Not used
−
PTT
PTT Signal
Input Impedance 100 kΩ
AI1
Programmable Function Input 1
Input Impedance 47 kΩ
MICG
MIC GND
MIC GND
−
AI2
Programmable Function Input 2
Input Impedance 47 kΩ
MIC
MIC Input
600 Ω
AI3
Programmable Function Input 3
Input Impedance 47 kΩ
HOOK
Hook Detection
Input Impeadance 100 kΩ
DG
Digital GND
Digital GND
−
NC
Not used
Not used
−
TD
TX Audio Input
Input Impedance 600 Ω
not Pre-emphasis
TA
TX Audio Input
Input Impedance 600 Ω
Pre-emphasis
10 RD
RX Audio Output
Load Impedance 4.7 kΩ
not De-emphasis
11
RX Audio Output
Load Impedance 4.7 kΩ
De-emphasis
12 RXG
RX Signal GND
RX Signal GND
−
13 SPM
Speaker Mute
Input Impedance 47 kΩ
14 BER CLK
For Bit Error Rate Clock
CMOS
15 EMON
External Monitor Switch
Input Impedance 47 kΩ
16 EPTT
External PTT Switch
Input Impedance 47 kΩ
17 SC
Squelch Control
Output level 0 or 3.3 V
COM (D-SUB 9 Pin) CONNECTOR
Pin
NO.
Pin Name
CD
Description
Carrier Detect
Specification
Conform to RS-232C standard
I/O
Notes
RD
Receive Data
Conform to RS-232C standard
SD
Send Data
Conform to RS-232C standard
DTR
Data Terminal Ready
Conform to RS-232C standard
SG
GND
GND
−
DSR
Data Set Ready
Conform to RS-232C standard
RTS
Request to Send
Conform to RS-232C standard
CTS
Clear to Send
Conform to RS-232C standard
CI
Ringer DET
Conform to RS-232C standard
TEST/ SPEAKER CONNECTOR
Pin
NO.
Pin Name
Description
Specification
I/O
SB
Power Output
13.8 V
SB
Power Output
13.8 V
NC
Not used
Not used
−
GND
GND
GND
−
GND
GND
GND
−
SPG
Speaker GND
Speaker GND
−
RD
RX Audio Output
Load impedance 4.7 kΩ
RSSI
RSSI Signal Output
Output Level 0 to 5 V
SPI
Internal Speaker Input
Short with "SPO"
10 AO1
Open Collector Terminal
Allowable current value MAX 200mA
11
Open Collector Terminal
Allowable current value MAX 200mA
AO2
12 SPO
External Speaker Output
Output Level 3W (5%Distortion)
13 AO3
Open Collector Terminal
Allowable current value MAX 200mA
14 AO4
Open Collector Terminal
Allowable current value MAX 200mA
15 AO5
Open Collector Terminal
Allowable current value MAX 200mA
Notes
RA
18 BER DAT
For Bit Error Rate Data
CMOS
19 TXG
TX Signal GND
TX Signal GND
20 IO1
Programmable Function I/O 1
Input Impedance 47 kΩ
I/O
Output level 0 or 5 V
21 IO2
Programmable Function I/O 2
Input Impedance 47 kΩ
I/O
Output level 0 or 5 V
22 IO3
Programmable Function I/O 3
Input Impedance 47 kΩ
I/O
Output level 0 or 5 V
23 IO4
Programmable Function I/O 4
Input Impedance 47 kΩ
I/O
Output level 0 or 5 V
24 IO5
Programmable Function I/O 5
Input Impedance 47 kΩ
I/O
Output level 0 or 5 V
25 IO6
Programmable Function I/O 6
Input Impedance 47 kΩ
I/O
Output level 0 or 5 V
−
LAN (Modular Jack)
Pin
NO.
not De-emphasis
Pin Name
Description
Specification
I/O
Notes
TD+
TX Signal +
Comform to IEEE802.3 standard
100 Mbps
TD-
TX Signal −
Comform to IEEE802.3 standard
100 Mbps
RD+
RX Signal +
Use Designated Transformer
100 Mbps
NC
Not used
Not used
−
NC
Not used
Not used
−
RD-
RX Signal −
Use Designated Transformer
NC
Not used
Not used
−
NC
Not used
Not used
−
100 Mbps
SYNC 1, 2 Connector (There are two connectors)
Pin
NO.
Pin Name
Description
Specification
FRMA
RS-485 Differential Signal A
Conform to RS485
NC
Not used
Not used
NC
Not used
Not used
FRMB
RS-485 Differential Signal B
Conform to RS485
RX ANT
TX ANT
Impedance 50 Ω
Impedance 50 Ω
REF IN
REF OUT
External Reference Signal Input (10 MHz). Impedance : more than 1 kΩ
Reference Signal Distribution (10 MHz). Load Impedance : more than 20 Ω
I/O
Notes
I/O
−
−
I/O
B59-2539-00
Addendum
Description de la borne
CONNECTEUR Commande E/S (D-SUB 25 broches)
MIC (Prise modulaire)
N° de
broche
Nom de broche
Description
Caractéristiques
E/S
Remarques
N° de
broche
Nom de broche
Description
Caractéristiques
E/S
Remarques
Non utilisé
−
NC
Non utilisé
Non utilisé
−
Puissance développée
13,8 V
NC
Non utilisé
Non utilisé
−
GND (terre)
GND (terre)
−
NC
Non utilisé
Non utilisé
−
Signal PTT (poussez-pour-parler)
Impédance entrée 100 kΩ
AI1
Entrée fonction programmable 1
Impédance entrée 47 kΩ
MICG
MIC GND
MIC GND
−
AI2
Entrée fonction programmable 2
Impédance entrée 47 kΩ
MIC
Entrée MIC
600 Ω
AI3
Entrée fonction programmable 3
Impédance entrée 47 kΩ
HOOK
Détection de support
Impédance entrée 100 kΩ
DG
GND numérique
GND numérique
−
NC
Non utilisé
Non utilisé
−
TD
TX Entrée audio
Impédance entrée 600 Ω
pas de pré-accentuation
TA
TX Entrée audio
Impédance entrée 600 Ω
Pré-accentuation
10 RD
RX Sortie Audio
Impédance de charge 4,7 kΩ
pas de désaccentuation
11 RA
RX Sortie Audio
Impédance de charge 4,7 kΩ
Désaccentuation
12 RXG
GND Signal RX
GND Signal RX
−
13 SPM
Haut parleur en sourdine
Impédance entrée 47 kΩ
14 BER CLK
Pour l'horloge des taux d'erreur sur les bits CMOS
NC
SB
GND
PTT
Non utilisé
CONNECTEUR COM (D-SUB 9 broches)
N° de
broche
Nom de broche
Description
Caractéristiques
Conforme au standard RS-232C
E/S
CD
Détection de porteuse
RD
Réception de données
Conforme au standard RS-232C
SD
Emission de données
Conforme au standard RS-232C
DTR
Terminal de données prêt
Conforme au standard RS-232C
SG
GND (terre)
GND (terre)
−
DSR
Poste de données prêt
Conforme au standard RS-232C
RTS
Demande pour émettre
Conforme au standard RS-232C
CTS
Voie libre
Conforme au standard RS-232C
CI
Tonalité DET
Conforme au standard RS-232C
Remarques
CONNECTEUR TEST/MICROPHONE
N° de
broche
Nom de broche
Description
Puissance développée
Caractéristiques
E/S
SB
SB
NC
GND
GND
SPG
Haut parleur GND
Haut parleur GND
−
RD
RX Sortie Audio
Impédance de charge 4,7 kΩ
RSSI
RSSI Sortie signal
Niveau de sortie 0 à 5 V
SPI
Entrée haut parleur interne
Court avec "SPO"
10 AO1
Borne de collecteur ouvert
Valeur de courant admissible 200mA
11 AO2
Borne de collecteur ouvert
Valeur de courant admissible 200mA
12 SPO
Sortie haut parleur externe
13 AO3
Borne de collecteur ouvert
14 AO4
Borne de collecteur ouvert
Valeur de courant admissible 200mA
15 AO5
Borne de collecteur ouvert
Valeur de courant admissible 200mA
Remarques
15 EMON
Commutateur de moniteur externe
Impédance entrée 47 kΩ
16 EPTT
Commutateur PTT externe
Impédance entrée 47 kΩ
17 SC
Commande du silencieux
Niveau de sortie 0 ou 3,3 V
18 BER DAT
Pour les données des taux d'erreur sur les bits CMOS
19 TXG
GND Signal de transmission
GND Signal de transmission
20 IO1
Fonction programmable E/S 1
Impédance entrée 47 kΩ
E/S
Niveau de sortie 0 ou 5 V
21 IO2
Fonction programmable E/S 2
Impédance entrée 47 kΩ
E/S
Niveau de sortie 0 ou 5 V
−
22 IO3
Fonction programmable E/S 3
Impédance entrée 47 kΩ
E/S
Niveau de sortie 0 ou 5 V
23 IO4
Fonction programmable E/S 4
Impédance entrée 47 kΩ
E/S
Niveau de sortie 0 ou 5 V
24 IO5
Fonction programmable E/S 5
Impédance entrée 47 kΩ
E/S
Niveau de sortie 0 ou 5 V
25 IO6
Fonction programmable E/S 6
Impédance entrée 47 kΩ
E/S
Niveau de sortie 0 ou 5 V
13,8 V
Puissance développée
13,8 V
Non utilisé
Non utilisé
−
GND (terre)
GND (terre)
−
N° de
broche
GND (terre)
GND (terre)
−
TD+
TD-
Signal − TX
Comforme au standard IEEE802.3
100 Mbps
RD+
Signal + RX
Utiliser le transformateur désigné
100 Mbps
NC
Non utilisé
Non utilisé
−
NC
Non utilisé
Non utilisé
−
RD-
Signal − RX
Utiliser le transformateur désigné
NC
Non utilisé
Non utilisé
−
Niveau de sortie 3W (Distorsion 5%)
NC
Non utilisé
Non utilisé
−
Valeur de courant admissible 200mA
LAN (Prise modulaire)
pas de désaccentuation
Nom de broche
Description
Signal + TX
Caractéristiques
Comforme au standard IEEE802.3
E/S
Remarques
100 Mbps
100 Mbps
Connecteurs SYNC 1, 2 (Il y a deux connecteurs)
N° de
broche
Nom de broche
Description
Caractéristiques
FRMA
Signal Différentiel A RS-485
Conforme au RS485
NC
Non utilisé
Non utilisé
NC
Non utilisé
Non utilisé
FRMB
Signal Différentiel B RS-485
Conforme au RS485
RX ANT
TX ANT
Impédance 50 Ω
Impédance 50 Ω
REF IN
REF OUT
Entrée signal de référence externe (10 MHz). Impédance : supérieure à 1 kΩ
Distribution signal de référence (10 MHz). Impédance de charge : supérieure à 20 Ω
E/S
Remarques
E/S
−
−
E/S
B59-2539-00
B59-2539-00_NXR-700-800_French.iA A
2008/02/21 10:18:29
MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS
• Use only manufacturer or dealer supplied antennas.
• Antenna Minimum Safe Distance: 180 cm (6 feet).
• Antenna Gain: 0 dBd referenced to a dipole.
The Federal Communications Commission has adopted a safety standard
for human exposure to RF (Radio Frequency) energy which is below the
OSHA (Occupational Safety and Health Act) limits.
• Antenna Mounting: The antenna supplied by the manufacturer or
radio dealer must not be mounted at a location such that during radio
transmission, any person or persons can come closer than the above
indicated minimum safe distance to the antenna, i.e. 180 cm (6 feet).
• To comply with current FCC RF Exposure limits, the antenna must be
installed at or exceeding the minimum safe distance shown above,
and in accordance with the requirements of the antenna manufacturer
or supplier.
• Vehicle installation: The antenna can be mounted at the center
of a vehicle metal roof or trunk lid, if the minimum safe distance is
observed.
• Base Station Installation: The antenna should be ixed-mounted on
an outdoor permanent structure. RF Exposure compliance must be
addressed at the time of installation.
Antenna substitution: Do not substitute any antenna for the one supplied
or recommended by the manufacturer or radio dealer.
You may be exposing person or persons to excess radio frequency
radiation. You may contact your radio dealer or the manufacturer for
further instructions.
Maintain a separation distance from the antenna to person(s) of at
least 180 cm (6 feet).
You, as the qualiied end-user of this radio device must control the
exposure conditions of bystanders to ensure the minimum separation
distance (above) is maintained between the antenna and nearby persons
for satisfying RF Exposure compliance. The operation of this transmitter
must satisfy the requirements of Occupational/Controlled Exposure
Environment, for work-related use, transmit only when person(s) are at
least the minimum distance from the properly installed, externally mounted
antenna. Transmit only when people outside the vehicle are at least the
recommended minimum lateral distance away from the antenna/vehicle.
B59-2667-00

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Create Date                     : 2011:05:20 10:22:05+09:00
Creator                         : Adobe InDesign CS2_J (4.0.5)
Modify Date                     : 2011:06:07 10:30:28-04:00
Title                           : 
Trapped                         : False
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Metadata Date                   : 2011:06:07 10:30:28-04:00
Creator Tool                    : Adobe InDesign CS2_J (4.0.5)
Format                          : application/pdf
Document ID                     : uuid:28dabc03-8f21-4c8c-b3d4-37759402540e
Instance ID                     : uuid:1572daee-c99d-4dfa-b6ba-9f759869e28b
Producer                        : Adobe PDF Library 7.0
Page Count                      : 8
EXIF Metadata provided by EXIF.tools
FCC ID Filing: K44371310

Navigation menu