JVC KENWOOD 371404 UHF Digital base repeater User Manual
JVC KENWOOD Corporation UHF Digital base repeater
User Manual
NXR-700/ NXR-800
INSTRUCTION MANUAL
© B62-1994-00 (K, K2)
09 08 07 06 05 04 03 02 01 00
MANUAL DE INSTRUCCTIONES
MODE D'EMPLOI
BASE-REPETIDOR DIGITAL VHF / BASE-REPETIDOR DIGITAL UHF
VHF DIGITAL BASE-REPEATER/ UHF DIGITAL BASE-REPEATER
BASE-RELAIS NUMÉRIQUE VHF/BASE-RELAIS NUMERIQUE UHF
◆ Thisrepeaterisintendedforuseasaxedbasestationwiththe
antennalocatedoutdoorsontherooftoporonanantennatower.
◆ UseonlythesuppliedDCcord.
◆ DonotremovetheferritecoreattachedtotheDCcord.Doingso
maycauseinterferencewithradiocommunications.
UNPACKING AND CHECKING EQUIPMENT
Note:Thefollowingunpackinginformationisforusebyyour
Kenwood dealer, an authorized Kenwood service center, or the
factory.
Carefullyunpacktherepeater.Werecommendthatyou
identifytheitemslistedinthefollowingtablebeforediscarding
thepackingmaterial.Ifanyitemsaremissingorhave
beendamagedduringshipment,leaclaimwiththecarrier
immediately.
Item Part Number Quantity
Frontglass B10-2781-XX 1
Dressedscrew N08-0563-XX 1
Bracket J29-0725-XX 2
Flatheadmachinescrew N32-4008-XX 4
Handleandscrewset K01-0421-XX 1
DC cord E30-3344-XX 1
Leadwirewithconnector(15pin) E37-1381-XX 1
Fuse(7.5A) F05-7521-XX 1
Instruction Manual B62-1994-XX 1
Serialnumbersticker B42-7325-XX 1
INSTALLATION
Toinstallthehandlesontothefrontpaneloftherepeater,align
thehandleswiththeholesonthefrontpanel,thensecurethe
handlesusingthesuppliedscrews.
Pleaseconsultyourdealerforinstallingtherepeaterand
antenna.
MICROPHONE
Connect an optional KMC-30, KMC-35, or KMC-9C Kenwood
microphone to the MICROPHONEjackonthefrontpanel.
NOTICES TO THE USER
FCC WARNING
Thisequipmentgeneratesorusesradiofrequencyenergy.Changes
ormodicationstothisequipmentmaycauseharmfulinterference
unlessthemodicationsareexpresslyapprovedintheinstruction
manual.Theusercouldlosetheauthoritytooperatethisequipmentif
anunauthorizedchangeormodicationismade.
◆ Governmentlawprohibitstheoperationofunlicensedradio
transmitterswithintheterritoriesundergovernmentcontrol.
◆ Illegaloperationispunishablebyneand/orimprisonment.
◆ Referservicetoqualiedtechniciansonly.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY
THE FCC
Thisequipmenthasbeentestedandfoundtocomplywiththelimits
foraClassBdigitaldevice,pursuanttoPart15oftheFCCRules.
Theselimitsaredesignedtoprovidereasonableprotectionagainst
harmfulinterferenceinaresidentialinstallation.
Thisequipmentgenerates,usesandcangenerateradiofrequency
energyand,ifnotinstalledandusedinaccordancewiththe
instructions,maycauseharmfulinterferencetoradiocommunications.
However,thereisnoguaranteethattheinterferencewillnotoccur
inaparticularinstallation.Ifthisequipmentdoescauseharmful
interferencetoradioortelevisionreception,whichcanbedetermined
byturningtheequipmentoffandon,theuserisencouragedtotryto
correcttheinterferencebyoneormoreofthefollowingmeasures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connect the equipment to an outlet on a circuit different from that to
whichthereceiverisconnected.
• Consultthedealerfortechnicalassistance.
THANK YOU!
WearegratefulyoupurchasedthisKenwoodrepeater.We
believethiseasy-to-programrepeaterwillbehighlyeffectivein
yourcommunicationssystem,andwillkeeppersonneloperating
atpeakefciency.
Kenwoodincorporatesthelatestinadvancedtechnologyinto
allofourproducts.Asaresult,wefeelstronglythatyouwillbe
pleasedwiththequalityandfeaturesofthisproduct.
PRECAUTIONS
• Donotexposetheunittorainormoisture;topreventreor
electricshock.
• Donotopentheunitunderanycircumstances;toavoidrisk
ofelectricshock.
• Donotexposetheunittolongperiodsofdirectsunlight,nor
placeitclosetoheatingappliances.
• Donotplacetheunitinexcessivelydustyand/orhumid
areas,noronunstablesurfaces.
• Ifyoudetectanabnormalodororsmokecomingfromthe
unit,disconnectthepowerfromtheunitimmediately.Contact
your Kenwood servicecenterordealer.
NXR-700 / NXR-800 INSTRUCTION MANUAL
VHF DIGITAL BASE-REPEATER / UHF DIGITAL BASE-REPEATER
REPEATER OPERATION
Note:Pleaseconsultyourdealerforprogrammingtherepeater.
WheoperatingtherepeaterusinganoptionalOCXOunit,allowthe
unittowarmupfor24hoursafterturningthepoweron.
Whenpowerisappliedtotheunit,thePOWERindicatorlights
green.TurntheVOLUMEcontrolclockwiseuntilaclicksounds,
tounmutethevolume.Rotatetoadjustthevolume.Turnthe
VOLUMEcontrolcounterclockwisefullytomutethevolume
The BUSYindicatorlightsgreenwhilereceivingasignalandthe
TXindicatorlightsredwhiletransmitting.
TRANSCEIVER OPERATION
■ Receive
Adjustthevolumetoyourdesiredlevel.Youmayneedto
■ Rear Panel
q RX IN jack
ConnectanRXantennaoraduplexertothisBNC
receptacle.
w TEST/SPKR jack
Testinput/outputjack.Connectanexternalspeakerto
thisjack.
e CONTROL I/O jack
ConnectanrepeatercontrollertothisDB-25interface.
r SYNC 1/2 jack
Connect to other repeater to use synchronous frame
signal.
t LAN jack
ConnecttoEthernet.
CONTROLS AND FUNCTIONS
■ Front Panel qw r t y u
io
e
qwr t yu
e
MICROPHONE
VOLUME
COM OFF/
POWERCTRL OCXO BUSY TX
1 2
MON
TAKE
OVER
RPT
DISABLE
A B C
3 4 5 6 7 8
STATUS
TEST/SPKR
RX TX
CONTROL I/O SYNC
1 2 LAN REF OUT REF IN
FUSE
75
DC 13.8V
y REF OUT jack
Connecttoanotherrepeaterwithinthesitetosupplya
referencesignal.
u REF IN jack
Connectfromanotherrepeaterwithinthesitetoreceivea
referencesignal.
i FUSE
Insert7.5Abladefusesintothesefuseholders.
o DC 13.8V jack
Connecta13.8VDCpowersupplytothisjack.
⑩ TX OUT jack
ConnectaTXantennaoraduplexertothisreceptacle.
io⑩
readjustthevolumewhenyoureceiveamessagefromyour
dispatcheroranothermemberinyoureet.
• The BUSYindicatorlightsgreenwhileasignalisbeing
received.
■ Transmit
1 Listentothechannelbeforetransmitting,tomakesureit
isnotbeingused.
2 Press the microphone PTTswitch,thenspeakinyour
normalspeakingvoice.
• The TXindicatorlightsredwhiletransmitting.
3 Whenyounishspeaking,releasethePTTswitch.
!0
!1
!2
q Speaker
w CH/STATUS Display
Two17-segmentdigitsdisplaythechannelnumber,name,
orstatus.
e STATUS indicator
Indicatesthestatusoftherepeater.
r Programmable Function keys
Pressthesekeystoactivatetheirprogrammable
functions.
t COM jack
ConnecttoPC.ConformtoRS-232Cstandard.
y VOLUME control
Turnclockwiseuntilaclicksounds,tounmutethevolume.
Rotatetoadjustthevolume.Turncounterclockwisefully
tomutethevolume.
u MICROPHONE jack
Connectamicrophonetothis8-pinmodularjack.
i POWER indicator
LightsgreenwhenpowerissuppliedtotheDC 13.8V
jack.Blinkswhenanabnormalvoltageispresent.
o TX indicator
Lightsredwhiletransmitting.
!0 BUSY indicator
Lightsgreenwhileasignalisbeingreceived.
!1 OCXO indicator
TheOCXOindicatorshowsthestateofthereference
10MHzoscillator:
LightsGreenwhenusingareferencesignalfroman
optionalOCXOunit.
LightsOrangewhenusingareferencesignalfromanother
repeater.
Lightsredwhennoreferencesignalisavailableorwhen
anerroroccurs.
Doesnotlightwhenthereferencesignalisaninternal
VCXOsignal.
!2 CTRL indicator
TheCTRLindicatorshowstheRCCHstatuswhileusing
Digitaltrunking:
LightsGreenwhentherepeaterisusedasRCCH.
BlinksGreenwhenusinganon-dedicatedchannel,and
RCCHisusedasRDCH.
DoesnotlightwhenusingRDCH.
MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS
• Use only manufacturer or dealer supplied antenna.
• Antenna Minimum Safe Distance: 60 cm (2 feet), 50% duty Cycle.
• Antenna Gain: 0 dBd referenced to a dipole.
The Federal Communications Commission has adopted a safety standard for human
exposure to RF (Radio Frequency) energy which is below the OSHA (Occupational
Safety and Health Act) limits.
• Antenna Mounting: The antenna supplied by the manufacturer or radio dealer must not
be mounted at a location such that during radio transmission, any person or persons
can come closer than the above indicated minimum safe distance to the antenna, i.e.
60 cm (2 feet) , 50% duty Cycle.
• To comply with current FCC RF Exposure limits, the antenna must be installed at or
exceeding the minimum safe distance shown above, and in accordance with the
requirements of the antenna manufacturer or supplier.
• Vehicle installation: The antenna can be mounted at the center of a vehicle metal roof
or trunk lid, if the minimum safe distance is observed.
• Base Station Installation: The antenna should be fixed-mounted on an outdoor
permanent structure. RF Exposure compliance must be addressed at the time of
installation.
Antenna substitution: Do not substitute any antenna for the one supplied or
recommended by the manufacturer or radio dealer.
You may be exposing person or persons to excess radio frequency radiation. You may
contact your radio dealer or the manufacturer for further instructions.
Maintain a separation distance from the antenna to person(s) of at least
60 cm (2 feet) , 50% duty Cycle.
You, as the qualified end-user of this radio device must control the exposure conditions
of bystanders to ensure the minimum separation distance (above) is maintained
between the antenna and nearby persons for satisfying RF Exposure compliance. The
operation of this transmitter must satisfy the requirements of Occupational/Controlled
Exposure Environment, for work-related use, transmit only when person(s) are at least
the minimum distance from the properly installed, externally mounted antenna. Transmit
only when people outside the vehicle are at least the recommended minimum lateral
distance away from the antenna/vehicle