JVC KENWOOD 39622A GPS NAVIGATION SYSTEM User Manual

JVC KENWOOD Corporation GPS NAVIGATION SYSTEM

Contents

User manual 2 of 2

72 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 73
Next page 3Next page 3
reduced the volume using the "Volume
Offset", the sound generated if you suddenly
switch to another source may be extremely
loud.
[Subwoofer Level] Adjusts the
subwoofer volume.
The setting is available when subwoofer
is set to any item other than "None". See
<Speaker Setup> (page 94).
[Bass Boost] Sets the amount of bass
boost. (DNX7 series only)
"OFF"/ "Step1"/ "Step2"
[Supreme] Turns ON/OFF the Supreme
function. (DNX9/ DDX8 series only)
Technology to extrapolate and
supplement with proprietary algorithm,
the high-frequency range that is cut off
when encoding.
This function works on DVD, USB, SD
and iPod sources.
Equalizer Control
Equalizer Control
You can set up the equalizer.
1 Display the Equalizer screen
Touch [ ]
>
> [ ]
>
> [Equalizer].
(page 72)
2 Select EQ curves
[Natural], [Rock], [Pops], [Easy],
[Top40], [Jazz], [Game], [iPod], [User]
Selects an equalizer curve type.
You can select any of the following
equalizer curves.
⁄
• [iPod]
During iPod source only.
[EQ] Displays the Graphic Equalizer
setup screen. (page 73)
Graphic Equalizer Setup
Graphic Equalizer Setup
You can Manually set the equalizer curve.
1 Display the Equalizer screen
Touch [ ]
>
> [ ]
>
> [Equalizer].
(page 72)
2 Display the Graphic Equalizer screen
⁄
• When "iPod" is selected in <Equalizer
Control>, the [EQ] button is deactivated.
"iPod" uses its equalizer function.
3 Select the channel to be adjusted
(DNX9/ DDX8 series only)
[F] Front speaker
[R] Rear speaker
[C] Center speaker
Audio Control Menu
Audio Control Menu
Displays the Audio Control menu to set the
sound effect function of this unit.
1 Display the Source Select Screen
When a video screen is displayed, press
the [SRC] button.
2 Display the Audio Control menu
In this manual, the above selection is
indicated as:
Touch [ ]
>
> [ ].
3 Select the Audio Control item
Item Page
[Audio Control] 72
[Equalizer] 73
[EQ] 73
[Zone Control] 74
[SRS WOW] 76
[Space Enhancer] 75
Audio Control
Item Page
[Position] 75
[Surround Control] 77
Audio Control
Audio Control
You can adjust the front/rear and right/left
audio balance.
1 Display the Audio Control screen
Touch [ ]
>
> [ ]
>
> [Audio
Control]. (page 72)
2 Set each item
DNX9/ DDX8 series
1
1
1
DNX7 series
1
1
1
1 Adjusts the front/back and left/right
volume around the touched area.
[2], [3] Adjusts the right and left
volume balance.
[5], [∞] Adjusts the front and rear
volume balance.
[Volume Offset] Finely adjust the
volume of the current source to
minimize the difference in volume
between different sources.
⁄
• If you have increased the volume first, then
74 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 75
Next page 3Next page 3
⁄
• There are following limitations when zone
function is set to "ON".
- There is no output from the subwoofer or
center speaker.
- "Bass Boost" of <Audio Control> (page 72) is not
available.
- <Equalizer Control> (page 73), <Space Enhancer>
(page 75), <Listening Position> (page 75), <SRS
WOW Control> (page 76), and <Surround
Control> (page 77) are not available.
- <DSP Bypass Control> (page 93), <Speaker
Setup> (page 94), <Car Type (DTA) Setup>
(page 95), and <Channel Level> (page 97) are not
available.
Space Enhancer (DNX7 series)
Space Enhancer (DNX7 series)
You can enhance the soundscape.
1 Display the Space Enhancer screen
Touch [ ]
>
> [ ]
>
> [Space
Enhancer]. (page 72)
2 Set the Space Enhancer
1
1
1
1 Sets the soundscape level.
⁄
• You cannot set Space Enhancer in tuner source.
Listening Position
Listening Position
You can adjust the sound effects according
to your listening position.
1 Display the Position screen
Touch [ ]
>
> [ ]
>
> [Position].
(page 72)
2 Set the Position Control
[P1] - [P3] Stores the present
adjustment setup in memory, or recalls
it from memory.
To store your adjustment in memory:
Continue to touch [P1] to [P3] more
than 2 seconds.
To call your adjustment from memory:
Touch [P1] to [P3] of your adjustment
you wish to recall from memory.
[2], [3] Sets a listening position.
You can select any of "Front R" (Right
front), "Front L" (Left front), "Front All"
(All front), "All" (All), and "User" (User)
positions.
[DTA] Displays the Position DTA (Digital
Time Alignment) screen.
3 Exit Position Control
⁄
• The final distance is adjusted to the total of Car
Type Set Up value (page 95) and Position Setup
(both Position and Position DTA) value.
• If you change the Car Type Set Up value (page 95),
the position is set to "All".
Zone Control
Zone Control
You can set the front and rear audio
source.
1 Display the Zone Control screen
Touch [ ]
>
> [ ]
>
> [Zone
Control]. (page 72)
2 Set the Zone Control
[Single Zone] Sets the unit to single
zone.
[Dual Zone] Sets the unit to dual zone.
[Front Source] Sets the front audio
source.
[Rear Source] Sets the rear audio
source.
⁄
• When the rear speaker sound is switched,
the audio source that is output at the AV
OUTPUT terminal is also switched to the
same source.
[Rear VOL.] Adjusts the volume of the
rear channel.
4 Set the Graphic Equalizer
DNX9/ DDX8 series
1
1
1
DNX7 series
1
1
1
1 Gain level can be adjusted by
touching the each frequency bar.
[2], [3] Sets a frequency.
[5], [∞] Sets a gain level.
[EQ Init] Returns to the previous level
which the gain level is adjusted.
[Flat] Tone curve becomes flat.
[Bass EXT] Bass Extend settings.
When turned on, the frequency lower
than 62.5 Hz is set to the same gain
level as 62.5Hz.
[SW Level] Adjusts the subwoofer
volume.
The setting is available when subwoofer
is set to any item other than "None". See
<Speaker Setup> (page 94).
Audio Control
76 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 77
⁄
• FOCUS: Adjusts the vertical position of the
speaker and sound image by virtual
adjustment.
• TruBass: Assists the playback for the super bass
sound.
• SRS 3D: Makes a natural 3D sound field.
• Some items cannot be adjusted depending on
the selected speaker.
• SRS WOW control is not available in tuner source,
TV source and HD Radio source.
• When Surround Control is Dolby Pro Logic II, SRS
WOW control is not available.
Surround Control
Surround Control
(DNX9/ DDX8 series)
(DNX9/ DDX8 series)
You can set up the sound field.
1 Display the Surround Control screen
Touch [ ]
>
> [ ]
>
> [Surround
Control]. (page 72)
2 Set the Surround Control
1
1
1
1 Sets a sound field.
You can select any of the following
sound fields.
"Bypass"/ "Bypass+Center"/ "Dolby
Pro Logic II Movie"/ "Dolby Pro Logic II
Music"/ "Dolby Pro Logic II Matrix"
[Stream Information] Displays the
present source information.
The stream (Dolby Digital, dts, Linear
PCM, MPEG, SDDS, AAC or MP3/WMA),
input channels (front or rear channels),
and sampling frequency are displayed.
⁄
• When you have selected the TV or TUNER source
and when you set the Dolby PL, we recommend
you to select the "Dolby PLII Matrix" mode. If you
select another Dolby PLII mode, the sound is
NOT output from rear speakers when you receive
monaural broadcasting sounds.
• Surround control can be set for each source.
Dolby Pro Logic II Music Adjustment
1 Display the Dolby Pro Logic II Music
Adjust screen
2 Adjust the sound field
[Dimension Control] Sets the surround
position by adjusting the front and rear
volume balance.
[Center Width Control] Sets the vocal
image position by adjusting the right
and left vocal volume level.
[Panorama Mode] Turns the Panorama
mode On or Off.
⁄
• You cannot use the <Surround Control
Adjustment> during playback of a Multi-channel
source.
• Only the adjusted distance of position setup
(Position and Position DTA values) is stored in
memory. Therefore, the final adjustment distance
changes if you change the Car Type Set Up value
(page 95).
Position DTA Control
You can fine-adjust your listening position.
1 Display the Position DTA screen
2 Select a speaker you wish to adjust
3
3
3
2
2
2
1
1
1
6
6
6
4
4
4
1 Center speaker (DNX9/ DDX8 series)
2 Left front speaker
3 Right front speaker
4 Left rear speaker
5 Right rear speaker
6 Subwoofer
[2], [3] Finely adjusts the value set with
the Position function.
[Total DTA] Indicates setup distance.
The adjusted distance (Position and
Position DTA values), and the total
of the distance adjusted by Car Type
Set Up (page 95) and the adjustment
distance for position setup are
indicated.
3 Finely adjust the distance
Finely adjust the value set with the
Position function.
SRS WOW Control
SRS WOW Control
(DNX9/ DDX8 series)
(DNX9/ DDX8 series)
You can set up the SRS WOW effect.
1 Display the SRS WOW Control screen
Touch [ ]
>
> [ ]
>
> [SRS WOW].
(page 72)
2 Set the SRS WOW Control
1
1
1
1 Selects SRS WOW setting.
SRS WOW User Setup
1 Display the SRS WOW Adjust screen
2 Adjust the SRS settings
1
1
1
1 Selects a speaker to be set (Front,
Rear or Center speaker).
[TruBass] Sets the TruBass effect level.
[FOCUS] Sets the FOCUS effect level.
[SRS 3D] Sets the SRS 3D effect level.
Audio Control
78 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 79
Next page 3Next page 3
DivX Setup (DNX9/ DDX8 series)
DivX Setup (DNX9/ DDX8 series)
Checks the registration code. This code
is needed when making a disc which has
DRM (Digital Rights Management).
1 Display the DivX Setup screen
Touch [ ]
>
> [ ]
>
> [DivX(R)
SETUP]. (page 78)
Displays the registration code.
⁄
• Disabled when a DVD is being played.
• When downloading a DivX VOD file controlled by
DRM, register the code appeared on the screen
such as the one above. Otherwise the file may
not be able to play with this unit. Remaining
number of viewing is displayed when playing a
DivX VOD file with the viewing restriction. When
the remaining number of viewing reached 0, a
warning message appears and the file cannot
be played.
Deactivating DivX Code
1 Display the DivX Deactivation
Confirm screen
2 Cancel the registration
Touching the screen displays a
confirmation message. Touch [OK].
To cancel clearing, touch [Cancel].
Software Information
Software Information
Checks the software version of this unit.
1 Display the Software Information
screen
Touch [ ]
>
> [ ]
>
> [Software].
(page 78)
Displays the software version.
⁄
• For how to update the software, refer to the
relevant update procedure manual which
comes with the software.
Setup Menu
How to Display SETUP Menu Screen
How to Display SETUP Menu Screen
Displays the Setup menu to set various
functions.
1 Display the Source Select Screen
When a video screen is displayed, press
the [SRC] button.
2 Display the Setup Menu Screen
In this manual, the above selection is
indicated as:
Touch [ ]
>
> [ ].
3 Select the setup item
⁄
• [AV-IN SETUP], [Navigation] and [Audio SETUP]
options can be locked. The key mark ( ) is
displayed in reverse video for the locked option.
You can set up various receiver parameters.
See <Setup Memory> (page 84).
Item Page
[DivX(R) SETUP] 79
[System]
[User Interface] 80
[Touch] 81
[Clock] 82
[Security] 82
[Angle] 82
[EXT SW] 83
[SETUP Memory] 84
[Display]
[Screen Control] 87
[Color] 86
[Background] 85
[Bluetooth SETUP] 88
[SIRIUS SETUP] 102
[DVD SETUP] 98
[iPod SETUP] 101
[USB SETUP] 101
[SD SETUP] 101
[TV SETUP] 101
[AV-IN SETUP] 91
[Navigation] 93
[Software] 79
[Audio SETUP] 93
[Speaker Select] 94
[Car Type] 95
[Channel Level] 97
[AV-OUT Interface] 91
[Camera SETUP] 92
80 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 81
Next page 3Next page 3
[Cancel] Cancels the selected language.
When [ASR] is set to "Disabled" (DNX9
only)
When [Select Mode] is set to
"Advanced"
[GUI Language Select] Selects the
display language used for the control
screen and so forth.
( "American English (en)")
[Navigation Language Select] Selects
the language used for navigation.
( "American English (en)") (DNX7
series only)
[User Text Language Select] Selects
the language used for tag text (song
information).
( "American English (en)")
Touch Panel Adjustment
Touch Panel Adjustment
You can adjust the touch panel operations.
1 Display the Touch panel Adjustment
screen
Touch [ ]
>
> [ ]
>
> [System]
>
>
[Touch]. (page 78)
2 Adjust the Touch panel
Follow the instruction on the screen and
touch the center of .
[Cancel] Cancels the Touch Panel Adjust.
[Reset] Resets to the initial status.
Setup Menu
display off.
"CAM": Press the [AUD] button for
longer than 1 second to switch to
camera view.
[Animation] Sets whether to display
animation. ( "ON")
Language Setting
Language Setting
You can select the display language for the
control screen and audio file tags.
1 Display the User Interface screen
Touch [ ]
>
> [ ]
>
> [System]
>
>
[User Interface]. (page 78)
2 Display the Language Setting screen
3 Select a language
[ASR] Selects whether to use the voice
control function. (page 56) ( "Enabled")
(DNX9960 only)
"Enabled": Voice control is activated.
"Disabled": Voice control is deactivated.
[Select Mode] Selects the mode to
select a language. ( "Easy")
Touching [Advanced] allows you to
select languages for respective items.
[Language Select] Selects a language.
( "American English (en)")
[Enter] Determines the selected
language.
User Interface
User Interface
You can setup user interface parameters.
1 Display the User Interface screen
Touch [ ]
>
> [ ]
>
> [System]
>
>
[User Interface]. (page 78)
2 Set each item
[Beep] Turns the key touch tone On or
Off. ( "ON")
[Remote Sensor] Selects a remote
control signal. ( "ON")
When turned "OFF", the remote control
of TV reception is rejected.
[Language] Select the language used
for the control screen and setting items.
See <Language Setting> (page 80).
[Scroll] Allows scrolling of text display
on the Source Control screen.
( "Manual")
"Auto": Scrolls the screen automatically.
"Manual": Allows you to scroll the
screen manually.
[Drawer Close] Sets whether to close
the function bar automatically.
( "Auto")
[AUD Key Longer than 1 Second] Sets
the function of the [AUD] button. (page
12)
"V.OFF": Press the [AUD] button for
longer than 1 second to turn the
82 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 83
Next page 3Next page 3
EXT SW Setup
EXT SW Setup
Sets up the exteral switch power mode.
1 Display the EXT SW screen
Touch [ ]
>
> [ ]
>
> [System]
>
>
[EXT SW]. (page 78)
2 Perform EXT SW Setup
[SW1 Name]/ [SW2 Name] Sets the
name of the external device. See <How
To Use the Character Entry Screen>
(page 83) for information on how to enter
a name.
[Output Pattern] Sets the power signal
output mode.
( EXT SW1: Pulse, EXT SW2: Level)
"Pulse": Generates a single power signal
pulse.
"Level": Continues output of high
power signal.
Sets to turn output on/off each time the
button on the EXT SW Control screen is
touched. See <External Device Power
Supply Control> (page 55).
[Pulse Set] Sets the Pulse signal output
time.
Outputs 500ms when "1" is set.
Increases by 200ms with each step. Up
to 100 steps can be set.
How To Use the Character Entry Screen
1
1
1
1 Enters characters.
[2], [3] Shifts the cursor.
[5], [∞] Scrolls up or down the
character button display.
[Shift] Toggles between uppercase and
lowercase.
[qwe]/ [abc] Sets the key layout of the
character buttons.
abc : Alphabetical key layout.
qwe : Qwerty key layout.
[Clear] Clears the character.
[Space] Enters a space.
If you erase a character, locate the
cursor on it and touch this button.
⁄
• You can enter characters only after you have
applied the parking brake.
Setup Menu
Clock and Date Setup
Clock and Date Setup
You can adjust the clock time.
1 Display the Clock Setup screen
Touch [ ]
>
> [ ]
>
> [System]
>
>
[Clock]. (page 78)
2 Setup the Clock
1
1
1
1 Adjusts month, day, year, hours, and
minute.
[Reset] Sets "00" minute.
Setup examples: 3:00 – 3:29 \ 3:00
3:30 – 3:59 \ 4:00
[Synchronize] Sets the clock time in
synchronization with the time data sent
from the navigation system or the RDS
station. ( DNX series: "Navigation",
DDX series: "RDS")
"OFF"/ "RDS"*1/ "Navigation"
When the synchronized mode is set, the
clock cannot be adjusted manually.
(*1 North American sales area only)
3 Adjust the date or clock time
Security Setup
Security Setup
A red indicator will blink on the unit after
the ACC is set to OFF, warning potential
thieves.
1 Display the Security screen
Touch [ ]
>
> [ ]
>
> [System]
>
>
[Security]. (page 78)
2 Setup the SI (Security Indicator)
[SI] Turns the SI function on or off.
If turned "ON", the security indicator on
the front panel flashes when the vehicle
ignition is off. ( "ON")
Monitor Angle Control
Monitor Angle Control
You can adjust the position of the monitor.
1 Display the Angle Setup screen
Touch [ ]
>
> [ ]
>
> [System]
>
>
[Angle]. (page 78)
2 Set the Monitor Angle
1
1
1
1 Sets the Monitor angle.
[Off Position] Stores the current
monitor angle as the angle during
power off.
84 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 85
Next page 3Next page 3
Changing Background image
Changing Background image
Loads an image from the connected USB
device and sets it for the background
image.
1 Connect the device which has the
image to load
2 Display the Background screen
Touch [ ]
>
> [ ]
>
> [Display]
>
>
[Background]. (page 78)
3 Change Standby
4 Display the Background Memory
screen
[Change] Selects an image for
background.
[Delete] Deletes the background image.
Touching the screen displays a
confirmation message. Touch [Yes]. To
cancel clearing, touch [No].
5 Select the image to load
6 Load the image
[] Rotates counter clockwise.
[] Rotates clockwise.
7 Select Background Change screen
8 Select an image for background
1
1
1
1 Returns to the initial background.
9 Set the image as the background
Setup Menu
Setup Memory
Setup Memory
Audio Control, AV-IN SETUP, AV Interface,
Navigation, and Audio SETUP settings can
be memorized. The memorized settings
can be recalled at any time. For example,
even when the settings are cleared due to
replacement of the battery, the settings
can be restored.
1 Display the SETUP Memory screen
Touch [ ]
>
> [ ]
>
> [System]
>
>
[SETUP Memory]. (page 78)
2 Start Setup Memory
[Lock] Locks the AV-IN SETUP,
Navigation, and Audio SETUP settings.
When [Lock] is selected, you cannot
change the AV-IN SETUP, Navigation,
and Audio SETUP settings.
[Yes] Memorizes or recalls the settings.
[No] To cancel the function, touch [No].
To cancel memorization, touch [No].
The SETUP Menu screen appears again.
3 Select a desired function
[Recall] Recalls the memorized settings.
[Memory] Memorizes the current
settings.
[Clear] Clears the currently memorized
settings.
4 Memorize or recall the settings
When memorizing the Audio Setup and
AV Interface settings:
If settings have already been memorized,
a confirmation message appears. Touch
[Yes]. To cancel memorization, touch
[No].
When recalling the memorized
settings:
Touching the screen displays a
confirmation message. Touch [Yes]. To
cancel recalling, touch [No].
When clearing the currently
memorized settings:
Touching the screen displays a
confirmation message. Touch [Yes]. To
cancel clearing, touch [No].
5 Quit memorization/recalling of
settings
86 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 87
Next page 3Next page 3
To register your original color
1 Start the RGB coordinate
2 Adjust each color value
1
1
1
1 Selects a preset number to register.
[Red Value] Adjusts the Red value.
[Green Value] Adjusts the Green value.
[Blue Value] Adjusts the Blue value.
3 Select a Preset number to register
2 sec.
Adjusted color is registered to the
selected Preset button.
4 Complete the color coordination
Screen Control
Screen Control
You can adjust the screen mode of the
monitor.
1 Display the Screen Control screen
Touch [ ]
>
> [ ]
>
> [Display]
>
>
[Screen Control]. (page 78)
2 Set each item
[Bright] Brightness Control
[Contrast] Contrast Control
[Black] Black Level Adjustment
[Dimmer] Dimmer Mode Setup
( "ON")
"ON": The display dims.
"OFF": The display doesn’t dim.
"SYNC": Turning the Dimmer function
On or Off when the vehicle light
control switch is turned On or Off.
"NAV-SYNC": Turning the Dimmer
function On or Off according to the
Navigation Day/Night display setting.
(DNX series and DDX series with
navigation unit only)
⁄
• In this Screen Control screen, you can perform
setups for the menu screen. Setups for videos
such as DVD can be performed on the <Screen
Control> (page 58).
Setup Menu
⁄
• See <About Picture files> (page 6) for readable
image specifications.
• The [Memory] button on the “Background” screen
becomes active only in STANDBY source mode.
• Pressing the [Memory] button on the
“Background” screen switches the AV OUT source
to OFF. For resetting the AV OUT source, refer to
<AV Output Interface Setup> (page 91).
Panel Color Coordinate
Panel Color Coordinate
DNX9/ DDX8 series : Sets the button
illumination color.
DNX7 series : Sets the screen and button
illumination color.
1 Display the Color screen
Touch [ ]
>
> [ ]
>
> [Display]
>
>
[Color]. (page 78)
2 Display the Panel Color Coordinate
screen
[Initialize] Initialization resets the
settings made using the Panel Color to
the default settings made at the factory.
[Panel Color Scan] When set to "ON",
the illumination color of the screen and
buttons changes one after another.
(DNX9/ DDX8 series only)
⁄
• When touching [SET] or [Initialize], make
sure [Panel Color Scan] is set to "OFF".
3 Select a color
1
1
1
1 Sets to the touched color.
[Adjust] Sets and registers favorite color
to the preset buttons ([P1] – [P3]).
88 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 89
Next page 3Next page 3
screen.
⁄
• You can also register from the Bluetooth unit
side. For the PIN code necessary for registration,
see <Registering Bluetooth Unit PIN Code>
(page 89).
• If pairing cannot be done even when the
PIN code is correct, try <Registering Special
Bluetooth Unit>.
Registering Special Bluetooth Unit
Registers Special Bluetooth unit that
results in error by normal operation by
selecting from model name.
1 Display the Special Device List screen
2 Select a model name
Displays the Bluetooth unit name that
can be registered.
3 Confirm whether to register
⁄
• Only models in Bluetooth unit name list can
be registered.
4 Go through the procedure of
<Registering Bluetooth Unit> and
complete the registration (pairing).
Registering Bluetooth Unit PIN
Registering Bluetooth Unit PIN
Code
Code
Sets the PIN code of the Bluetooth unit to
enter when registering (pairing) from the
cell-phone or audio player side.
1 Display the Bluetooth Setup screen
Touch [ ]
>
> [ ]
>
> [Bluetooth
SETUP]. (page 78)
2 Display the Receiver PIN Code screen
3 Enter PIN code
1
1
1
1 Enters a code number.
[Cancel] Cancels registration of PIN
code.
[Enter] Enters PIN code.
[Clear] Clears the code number.
Setup Menu
Registering Bluetooth Unit
Registering Bluetooth Unit
Registers the Bluetooth unit to be
connected.
1 Display the Bluetooth Setup screen
Touch [ ]
>
> [ ]
>
> [Bluetooth
SETUP]. (page 78)
2 Display the Connect Device List
screen
3 Search for a Bluetooth unit
1
1
1
1 Displays the registered Bluetooth
units.
[] When appears, the text display
is scrolled by touching it.
[Search] Searches for a Bluetooth unit.
[SP DEV] Registers a Bluetooth unit that
cannot be registered by normal register
(paring) operation.
⁄
• A new device cannot be registered if there
are 5 registered Bluetooth units. Delete
unnecessary registration. See <Bluetooth
Unit Connection> (page 90).
4 Display the PIN Code Set screen
1
1
1
1 Display the PIN Code.
[Search] Searches for a Bluetooth unit.
[Cancel] Cancels searching of Bluetooth
unit.
[PIN Code Set] Display the PIN Code
Set screen.
5 Enter PIN code
1
1
1
1 Enters a code number.
[Enter] Enter the PIN code specified for
the Bluetooth unit to register.
This button will not be active until at
least four PIN code digits have been
entered.
[Cancel] Cancels registration of PIN
code.
[Clear] Clears the code number.
6 Select the Bluetooth unit to register
1
1
1
1 Displays the searched Bluetooth unit.
Returns to the Connect Device List
90 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 91
Next page 3Next page 3
AV Input Setup
AV Input Setup
You can set AV input parameters.
1 Display the AV-IN Setup screen
Touch [ ]
>
> [ ]
>
> [AV-IN SETUP].
(page 78)
2 Set each item
[AV-IN Interruption] Sets an image
display of the system that is connected
via the AV INPUT port. ( "OFF")
"OFF": When the image source is
switched, an image entered via the AV
INPUT port is displayed.
"ON": When an image signal is entered
via the AV INPUT port, this image is
displayed.
[iPod AV Interface Use] Sets the
terminal which iPod is connected.
( "iPod")
[AV-IN1 Name], [AV-IN2 Name], [AV-IN3
Name] Sets a name to be displayed
when you select a system that is
connected via the AV INPUT port.
( "VIDEO")
⁄
• [iPod AV Interface Use]
This item can be set when in STANDBY source
and also the iPod is disconnected.
• [AV-IN Name]
Two AV-IN names are displayed when "iPod" is
selected in [iPod AV Interface Use] and three are
displayed when not selected.
• [AV-IN3 Name]
DNX9/ DDX8 series only
AV Output Interface Setup
AV Output Interface Setup
You can set AV output parameters.
1 Display the AV-OUT Interface screen
Touch [ ]
>
> [ ]
>
> [AV-OUT
Interface]. (page 78)
2 Set each item
[AV-OUT] Selects an AV source to be
output at the AV OUTPUT port.
( "OFF")
Setup Menu
Bluetooth Unit Connection
Bluetooth Unit Connection
Selects the Bluetooth unit to connect.
1 Display the Bluetooth Setup screen
Touch [ ]
>
> [ ]
>
> [Bluetooth
SETUP]. (page 78)
2 Display the Connect Device List
screen
3 Select a registered Bluetooth unit
4 Select the service to use
[TEL (HFP)] Connects/disconnects cell-
phone to use for Hands Free.
[Audio (A2DP)] Connects/disconnects
Audio player to use for Bluetooth Audio.
[Remove] Deletes registration (pairing).
Touching the screen displays a
confirmation message. Touch [Yes]. To
cancel clearing, touch [No].
Bluetooth Hands-Free/Audio
Bluetooth Hands-Free/Audio
Output Setup
Output Setup
Selects speakers to output the sound of
hands-free phoning (such as phone call
voice and ringing tone) and Bluetooth
audio.
1 Display the Bluetooth Setup screen
Touch [ ]
>
> [ ]
>
> [Bluetooth
SETUP]. (page 78)
[Bluetooth HF/Audio] Sets the output
speakers. ( "Front Only")
"Front Only": Outputs from the front
speakers.
"All": Outputs from all the speakers.
92 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 93
Next page 3Next page 3
Navigation Setup
Navigation Setup
You can set Navigation parameters.
1 Display the Navigation Setup screen
Touch [ ]
>
> [ ]
>
> [Navigation].
(page 78)
2 Set each item
[NAV Interrupt Speaker] Selects
speakers used for voice guidance of the
navigation system. ( "Front All")
"Front L": Uses the front left side
speaker for voice guidance.
"Front R": Uses the front right side
speaker for voice guidance.
"Front All": Uses both front speakers for
voice guidance.
[NAV Voice Volume] Adjusts the
volume for voice guidance of the
navigation system.
( DNX series: "25", DDX series: "21")
[NAV Mute] Mutes the volume of rear
speakers during voice guidance of the
navigation system. ( "ON")
When turned "ON", the volume level
drops for voice guidance.
[Navigation Input] Selects a navigation
system connection. ( "RGB") (DDX
series only)
"RGB": Allows the Kenwood’s
Navigation System to connect via its
interface cable.
"AV-IN": Allows a third-party navigation
system to connect via the AV INPUT1
port.
"OFF": Must be used if no navigation
system is connected. (The navigation
display is cancelled when the AV
source is switched.)
[On Screen Navigation] Sets an
on-screen display of the navigation
screen. ( "OFF") (DDX series only)
"Auto": Information is displayed for 5
seconds when updated. (Example :
when the track/file/song has changed
to the next one.)
"OFF": Information is not displayed.
⁄
• [On Screen Navigation]
It can be set only when [Navigation Input] is set
to "AVIN".
DSP Bypass Control (DNX7 series)
DSP Bypass Control (DNX7 series)
Temporarily bypassing DSP (Digital Signal
Processor) System.
1 Display the Audio SETUP screen
Touch [ ]
>
> [ ]
>
> [Audio SETUP].
(page 78)
2 Set the DSP Select
[Bypass] There is no effect by DSP.
[Through] There is an effect by DSP.
⁄
• When the mode is set to [Bypass], DSP System
cannot be adjusted.
Setup Menu
Camera Setup
Camera Setup
You can set Camera parameters.
1 Display the AV Interface screen
Touch [ ]
>
> [ ]
>
> [Camera
SETUP]. (page 78)
2 Set each item
[Rear Camera] Selects the type of rear
camera to use. ( "Other")
"CMOS-300": When the CMOS-300 with
ID 1 set is connected.
"Other": When the other camera is
connected.
[R-CAM Interruption] Sets a method
to switch to the rear view camera video
display. ( "OFF")
"ON": Switches to the rear view camera
video display when engaging the shift
knob of car to "Reverse".
"OFF": Switches to the rear view camera
video display when engaging the shift
knob of car to "Reverse" and then
pressing the [AUD] button for longer
than 1 second.
The function of the [AUD] button
needs to be set to "CAM" in [AUD Key
Longer than 1 Second] beforehand.
[R-CAM Settings] Adjusts the CMOS-
300 with ID 1 set. For details, see the
option manual.
[F-CAM on AV-IN1] Turn this setting
on when the CMOS-300 with ID2 set is
connected. ( "OFF")
[F-CAM Settings] Adjusts the CMOS-
300 with ID 2 set. For details, see the
option manual.
94 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 95
Next page 3Next page 3
2 Display the Crossover setup screen
3 Set the crossover
[Phase] Sets the phase of subwoofer
output.
The phase is reversed 180 degrees
when set to "Reverse". (Only when
"Subwoofer" is set to any item other
than "None" in Speaker Setup)
[HPF FREQ] High Pass Filter adjustment.
(When front, center or rear speaker is
selected on Speaker Select screen)
[LPF FREQ] Low Pass Filter adjustment.
(When Subwoofer is selected on
Speaker Select screen)
[Slope] Sets a crossover slope.
Car Type (DTA) Setup
Car Type (DTA) Setup
You can setup the car type and speaker
network, etc.
1 Display the Car Type Setup screen
Touch [ ]
>
> [ ]
>
> [Audio SETUP]
>
> [Car Type]. (page 78)
2 Setup the Car Type
If your car type is selected, the Digital
Time Alignment and Equalizer is set
automatically (for timing adjustment of
sound output for each channel) to have
the highest surround effects.
1
1
1
1 Sets up the car type you use together
with this unit.
You can choose according to type of
your car.
"OFF", "Compact", "Full Size Car",
"Wagon", "Minivan", "SUV", "Minivan
(Long)"
[Location] Sets the locations of the
speakers.
[Adjust] Displays the Car Type Adjust
screen.
You can adjust the digital time
alignment that was set automatically
when you selected the car type.
Setup Menu
Speaker Setup
Speaker Setup
You can select a speaker type and its size
to get the best sound effects.
1 Display the Speaker Select screen
Touch [ ]
>
> [ ]
>
> [Audio SETUP]
>
> [Speaker Select]. (page 78)
2 Select a speaker you wish to adjust
When the speaker type and size are
set, the speaker crossover network and
equalizer curve are set automatically.
2
2
1
1
1
3
3
3
4
4
4
1 Center speaker (DNX9/ DDX8 series)
2 Front speaker
3 Rear speaker
4 Subwoofer
[Tweeter] You can set the tweeter when
you are selecting front speakers.
If you are using a tweeter together with
the front speakers, set the tweeter to
"ON". In the "ON" position, the Equalizer
is adjusted to its best position.
[X'over] Displays the Speaker Crossover
Setup screen.
You can adjust the crossover setup
that was set automatically when you
selected the speaker type.
3 Select a speaker type
You can select any of the following
speaker types.
"Center" None, 2-3/4x1-9/16 inch, 2 inch,
4 inch, 5 inch, 6-1/2 inch over
"Front" OEM, 4 inch, 5 inch, 6-1/2 inch,
6-3/4 inch, 7 inch, 4x6, 5x7, 6x8, 6x9,
7x10
"Rear" None, OEM, 4 inch, 5 inch, 6-1/2
inch, 6-3/4 inch, 7 inch, 4x6, 5x7, 6x8,
6x9, 7x10
"Subwoofer" None, 6 1/2 inch, 8 inch, 10
inch, 12 inch, 15 inch over
⁄
• Select "None" if you have no speakers.
• If you set the center speaker to "None" even in
a short time when you are setting the Surround
Control to "Bypass+Center", the Surround Control
is set to "Bypass" automatically. See <Surround
Control> (page 77).
• If you set the center and rear speakers to "None"
when you are setting the Surround Control
to "Dolby PL II", the Surround Control is set to
"Bypass" automatically. See <Surround Control>
(page 77).
Crossover Network Setup
You can set a crossover frequency of
speakers.
1 Select the speaker to set the
crossover
2
2
2
1
1
1
3
3
3
4
4
4
1 Sets the High Pass Filter of the center
speaker. (DNX9/ DDX8 series)
2 Sets the High Pass Filter of the front
speaker.
3 Sets the High Pass Filter of the rear
speaker.
4 Sets the Low Pass Filter of the
subwoofer.
96 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 97
Next page 3Next page 3
sitting in the front seat, and set the
right and left positions to the center of
the vehicle interior.
2 Measure the distances from the
reference point to the speakers.
3 Calculate the distance difference in
accordance with the farthest speaker.
1.6feet
2.5feet
5feet +2.5feet
+0feet
+3.4feet
Channel Level (DNX9/ DDX8 series)
Channel Level (DNX9/ DDX8 series)
You can set the volume at each setup
position.
1 Display the Car Type Setup screen
Touch [ ]
>
> [ ]
>
> [Audio SETUP]
>
> [Channel Level]. (page 78)
2 Select a speaker you wish to adjust
2
2
2
1
1
1
4
4
4
3
3
3
5
5
5
6
6
6
1 Center speaker
2 Left front speaker
3 Right front speaker
4 Left rear speaker
5 Right rear speaker
6 Subwoofer
[Test Tone] Starts or stops test signal
tone output for setup check.
3 Adjust the volume
Setup Menu
Speaker Location setup
1 Display the Speaker Location Setup
screen
2 Set the speaker locations
[Front Speaker] Sets the location of the
front speaker.
"Door", "On Dash", "Under Dash"
[Rear Speaker] Sets the location of the
rear speaker.
"Door", "Rear Deck"
"2nd Row", "3rd Row" (Minivan, Minivan
(Long))
Car Type Adjust
You can manually set the sound output
timing of each channel.
1 Display the Car Type Adjust screen
2 Select a speaker you wish to adjust
2
2
2
1
1
1
3
3
3
4
4
4
1 Center speaker (DNX9/ DDX8 series)
2 Front speaker
3 Rear speaker
4 Subwoofer
3 Set a delay time
Make fine adjustment of the delay time
of the speaker output specified at <Setup
the Car Type> to have a more suitable
environment for your vehicle.
The settings of the delay time
are automatically identified and
compensated by specifying the distances
of each speaker from the center of the
vehicle interior.
1 Set the front and rear positions and
the height of the reference point to
the position of the ears of the person
98 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 99
Next page 3Next page 3
DVD Language Setup
DVD Language Setup
Selects a language you use for the speech
and menus.
1 Display the DVD Setup screen
Touch [ ]
>
> [ ]
>
> [DVD SETUP].
(page 78)
2 Select the language item to set
3 Enter a language code
See <DVD Language Codes> (page 115)
and select the desired language.
1
1
1
1 Enters a language code.
[Cancel] Cancels the language setup
and returns to the "DVD SETUP" screen.
[Enter] Sets the language and returns
to the "DVD SETUP" screen. (It appears
after you have entered a language
code.)
[Original] Sets the DVD's original
language (only when setting an audio
language).
[Clear] Clears the language code.
4 Set the language you use
DVD Parental Level Setup
DVD Parental Level Setup
Sets a parental level.
1 Display the DVD Setup screen
Touch [ ]
>
> [ ]
>
> [DVD SETUP].
(page 78)
2 Display the Parental Level code
number screen
3 Enter the code number
1
1
1
1 Enters a code number.
[Cancel] Cancels the current setup and
returns to the "DVD SETUP" screen.
[Level] Indicates the present parental
lock level.
[Enter] Determines the code number
and displays the Parental Level setup
screen.
Setup Menu
DVD Setup
DVD Setup
You can set up the DVD play.
1 Display the DVD Setup screen
Touch [ ]
>
> [ ]
>
> [DVD SETUP].
(page 78)
2 Set each item
[Menu Language]*1 Selects a disc
menu language. See <DVD Language
Setup> (page 99).
[Subtitle Language]*1 Selects a subtitle
language. See <DVD Language Setup>
(page 99).
[Audio Language]*1 Selects an audio
language. See <DVD Language Setup>
(page 99).
[Dynamic Range Control]*1 Sets the
dynamic range. ( "Dialog")
The dynamic range is reduced by
changing from "Wide" to "Normal"
and from "Normal" to "Dialog". "Dialog"
makes the total sound volume becomes
larger as compared with "Wide" and
"Normal", allowing you to listen to the
movie's dialog more clearly.
This is effective only when you are using
a Dolby Digital software.
The operation is available during the
play stop mode.
[Angle Mark] Sets an angle mark
display. ( "ON")
[Screen Ratio]*1 Selects the screen
display mode. ( "16:9")
"16:9": Displays wide pictures.
"4:3 LB": Displays wide pictures in the
Letter Box format (having black stripes
at the top and bottom of screen).
"4:3 PS": Displays wide pictures in the
Pan & Scan format (showing pictures
cut at the right and left ends).
[Parental Level]*1 Displays the Parental
Lock screen. ( "OFF")
See <DVD Parental Level Setup> (page
99).
[Disc SETUP] Makes the settings related
to the disc media. See <Disc Setup>
(page 100).
[Stream Information] Displays the
present source information.
The stream (Dolby Digital, dts, Linear
PCM, MPEG, MP3, WMA or AAC) is
displayed. (DNX7 series only)
⁄
• * Disabled when a DVD is being played.
100 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 101
Next page 3Next page 3
⁄
• [CD Read]
Disabled when a disc is in the unit.
You cannot play an Audio file/VCD disc in the
"2" position. Also, you may not play some music
CDs in the "2" position.
USB Setup
USB Setup
Performs setup when using USB.
1 Display the USB Setup screen
Touch [ ]
>
> [ ]
>
> [USB SETUP].
(page 78)
2 Set each item
Example : USB Setup screen
[Picture Display Time] Selects a picture
display time. ( "Long")
The Display of a JPEG picture is
changed. ("Short", "Middle", "Long")
[On Screen USB] Sets an on-screen
display of the USB Playback screen.
( "Auto")
"Auto": Information is displayed for 5
seconds when updated.
"OFF": Information is displayed when
you touch on the screen.
iPod Setup
iPod Setup
Performs setup when using iPod.
1 Display the iPod Setup screen
Touch [ ]
>
> [ ]
>
> [iPod SETUP].
(page 78)
2 Set each item
[AudioBook Speed] Sets the Audio
book playback speed. ( "Normal")
[Wide Screen] Sets Wide Screen on or
off. ( "OFF")
[On Screen iPod] Sets an on-screen
display of the iPod Playback screen.
( "Auto")
"Auto": Information is displayed for 5
seconds when updated.
"OFF": Information is displayed when
you touch on the screen.
⁄
• "Wide Screen" cannot be set while the iPod is
connected.
Setup Menu
[Clear] Clears the code number.
⁄
• The number you enter first is set as your
code number.
4 Display the Parental Level SETUP
screen
5 Select a parental level and complete
the setup
Selects a parental level.
⁄
• If a disc has higher parental lock level, you need
to enter the code number.
• The parental lock level varies depending on a
loaded disc.
• If a disc has no parental lock, anybody can play it
back even when you have set the parental lock.
Disc Setup
Disc Setup
Performs setup when using disc media.
1 Display the DVD Setup screen
Touch [ ]
>
> [ ]
>
> [DVD SETUP].
(page 78)
2 Display the Disc Setup screen
3 Set each item
[CD Read] Sets a music CD playback.
( "1")
"1": Automatically recognizes and plays
back an Audio file disc, a DVD or a
music CD.
"2": Forcibly plays back a disc as a
music CD. Select "2" if you wish to
play a music CD having a special
format or if you cannot play a disc in
the "1" position.
[On Screen DVD] Sets an on-screen
display of the DVD Playback screen.
( "OFF")
"Auto": Information is displayed for 5
seconds when updated.
"OFF": Information is not displayed.
102 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 103
Next page 3Next page 3
Parental Lock Setup
Parental Lock Setup
Selects the channel to enable SIRIUS
Parental lock function.
1 Display the SIRIUS Setup screen
Touch [ ]
>
> [ ]
>
> [SIRIUS
SETUP]. (page 78)
2 Display the Parental Code screen
⁄
• You need to complete <SIRIUS Parental
Code Setup> beforehand.
3 Enter the code number
Enter the same code number as you
originally input <SIRIUS Parental Code
Setup> (page 102).
4 Display the Parental Code screen
5 Enter the code number
6 Select a category
1
1
1
1 Category list
Displays all the channels in the selected
category.
[All Channel] Displays all the channels.
7 Set the parental lock for each
channel
3
3
3
1
1
1
2
2
2
1 Channel list
2 Sets the Parental lock function on or
off for each channel.
3 Selects a channel
[Info Change] Switch the sequence of
the channel list. (Channel name, Song
title, Artist name, Composer name, and
Category name)
[UP] Moves to SIRIUS Category
Select screen.
Setup Menu
SIRIUS Parental Code Setup
SIRIUS Parental Code Setup
Sets a SIRIUS Parental code. (with the
optional accessory SIRIUS Tuner connected
only)
1 Display the SIRIUS Setup screen
Touch [ ]
>
> [ ]
>
> [SIRIUS
SETUP]. (page 78)
2 Display the Parental Code screen
⁄
• If you have already completed the code
registration, [Change] is displayed.
3 Enter the Parental Code number
1 Enters a code number.
[Cancel] Cancels the current setup and
returns to the SIRIUS Setup screen.
[Enter] Determines the code number.
[Clear] Clears the code number.
4 Confirm the code number
Enter the same code number as you
input in step 3.
SIRIUS Parental code is now set, and the
display returns to SIRIUS Setup screen.
Change the Parental Code
1 Display the Parental Code screen
[Clear] Clears the Parental Code.
⁄
• Pressing [Clear] for 5 seconds or longer
deletes the code.
2 Enter the current code number
1
1
1
3 Enter the new code number
4 Confirm the code number
Enter the same code number as you
input in step 3.
SIRIUS Parental code is now set, and the
display returns to SIRIUS Setup screen.
104 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 105
Next page 3
Remote Controller
This unit can be operated using the Remote Controller supplied with this unit.
Battery installation
Battery installation
Use two "AAA"/"R03"-size batteries.
Insert the batteries with the + and – poles
aligned properly, following the illustration
inside the case.
⁄
• If the Remote Controller operates only over
shorter distances or does not operate at all, it is
possible that the batteries are depleted. In such
instances, replace the both batteries with new
ones.
Remote Controller mode switch
Remote Controller mode switch
The functions operated from the remote
controller differ depending on the position
of the mode switch.
DVD
TV
NAV
AUD
U
U
U
U
AUD mode
Switch to this mode when controlling a
selected source or tuner source, etc.
DVD mode
Switch to this mode when playing DVDs or
CDs etc. with the player integrated in this
unit.
¤ CAUTION
• Put the Remote Controller in a place where it will not move during braking or other operations. A
dangerous situation could result, if the Remote Controller falls down and gets wedged under the pedals
while driving.
• Do not leave the battery near fire or under direct sunlight. A fire, explosion or excessive heat generation
may result.
• Do not recharge, short, break up or heat the battery or place it in an open fire. Such actions may cause
the battery to leak fluid. If spilled fluid comes in contact with your eyes or on clothing, immediately rinse
with water and consult a physician.
• Place the battery out of reach of children. In the unlikely event that a child swallows the battery,
immediately consult a physician.
Setup Menu
SIRIUS Skip Channel Select
SIRIUS Skip Channel Select
Sets the undesired channels unselected.
1 Display the SIRIUS Setup screen
Touch [ ]
>
> [ ]
>
> [SIRIUS
SETUP]. (page 78)
2 Display the Skip Category Select
screen
3 Select a category
1
1
1
1 Category list
Displays all the channels in the selected
category.
[All Channel] Displays all the channels.
4 Set the skip for each channel
3
3
3
1
1
1
2
2
2
1 Channel list
2 Sets the skip function on or off for
each channel.
3 Selects a channel
[Info Change] Switch the sequence of
the channel list. (Channel name, Song
title, Artist name, Composer name, and
Category name)
[UP] Moves to SIRIUS Category
Select screen.
TV Setup
TV Setup
The TV signal receiving areas can be set.
(with the optional accessory TV Tuner
connected only)
1 Display the TV SETUP screen
Touch [ ]
>
> [ ]
>
> [TV SETUP].
(page 78)
2 Set each item
[On Screen TV] Sets an on-screen
display of the TV screen.
( "Auto") (with the optional accessory
TV tuner connected only)
"Auto": Information is displayed for 5
seconds when updated.
"OFF": Information is displayed when
you touch on the screen.
106 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 107
Next page 3Next page 3
Hands-free communication
When a call comes in, it answers the call.
Function
Switches the function screen
MODE
Switches the screen mode.
Screen mode changes each time you press
this key.
DVD/VCD (DVD mode)
DVD/VCD (DVD mode)
Track search and file search
Selects the track or file to be played.
Play/Pause
Pauses the track.
Press again to resume playing.
Stop
Memorizes the last point where the disc
stopped. When pressed again, the last point
is deleted.
Direct search
Pressing this key switches the features that
can be searched directly.
DVD-VIDEO
Title number
Chapter number
Play time
Item number*
Cancel
* You may not be able to use this function with
some discs or scenes.
Remote Controller
Dual Zone
Switches the Dual Zone function ON and
OFF.
Rear volume control
Adjusts volume at rear when the Dual Zone
function is ON.
V.SEL
Switches to the navigation screen.
Display angle
Switches the display angle each time it is
pressed.
Cursor key
Moves the cursor when displaying menu.
ENTER
Enters options.
TV mode
This is switched when controlling TV.
NAVI mode
This is switched when controlling
Navigation unit.
⁄
• The position of the remote control mode switch
is indicated in the title of each mode, e.g., "(AUD
mode)".
• When controlling a player that is not integrated
in the unit, select "AUD" mode.
Common operations (AUD mode)
Common operations (AUD mode)
Source switching
Switches to the source to be played.
Volume control
Adjusts the volume.
Volume attenuator
Press the key once to lower the volume.
Press again to restore the previous volume.
108 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 109
Next page 3Next page 3
Remote Controller
SUBTITLE
Switches the subtitle language.
ZOOM
Switches the zoom ratio each time you
press this key.
Picture Angle
Switches the picture angle each time you
press this key.
AUDIO
Switches the voice language each time you
press this key.
VCD 1.X, VCD 2.X (PBC OFF)
Track number
Cancel
VCD 2.X (PBC ON)
Scene number
Number
Cancel
Once you have switched to the direct
search feature, specify the search number
from the numeric keypad, and then press
[ENTER] key.
Numeric keypad
• Specify the number to search in direct
search.
• Press
1
2
ABC
to fast forward/
backward. Switches the fast forward/
backward speed each time you press this
key.
• Press
4GHI
5JKL
to slow forward/
backward. Switches the slow playback
speed each time you press this key.
DVD Top Menu
Returns to the DVD top menu.
DVD Menu
Displays the DVD menu.
Turns the playback control on or off while
playing VCD.
Music CD/Audio file/Video file/
Music CD/Audio file/Video file/
Picture file (AUD mode)
Picture file (AUD mode)
Folder search
Selects the folder to be played.
Track search and file search
Selects the track or file to be played.
Play/Pause
Pauses the track or file.
Press again to resume playing.
Direct search
Pressing this key switches the features that
can be searched directly.
Music CD
Track number
Play time
Cancel
Audio files in DVD/CD disc
Folder number
File number
Cancel
Once you have switched to the direct
search feature, specify the search number
from the numeric keypad, and then press
[38] key.
Numeric keypad
• Specify the number to search in direct
search.
iPod (AUD mode)
iPod (AUD mode)
Music/Video search
Selects the music/video to be played.
Play/Pause
Pauses the music/video.
Press again to resume playing.
110 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 111
Next page 3Next page 3
ROUTE M
Displays Route Option menu.
VIEW
Switches between 2D and 3D map displays.
VOICE
Plays Voice guidance.
MAP DIR
Switches between the heading up
navigation and north up navigation map
displays.
Remote Controller
Radio (AUD mode)
Radio (AUD mode)
FM band switching
Switches to bands received by the unit.
AM band
Station selection
Switches to broadcast stations received by
the unit.
Seek mode switching
Switches the Seek mode (AUTO1, AUTO2,
MANU).
Direct tuning
After pressing this key, use the keypad to
specify the broadcast station you wish to
receive.
Example: 92.1MHz (FM)
9
WXYZ
2ABC
1
«
or
Example: 810kHz (AM)
8TUV
1
0
«
or
Numeric keypad
• To use preset tuning, press the number
of a programmed broadcast station.
(
1
–
6
MNO )
• Press the direct tuning key first, then
specify the frequency of the station to
receive.
NAVI (NAVI mode)
NAVI (NAVI mode)
Cursor key
Scrolls the map, or moves the cursor.
ENTER
Performs the selected function.
ZOOM
Zooms in or out the navigation map.
MENU
Displays Main menu.
CANCEL
Displays previous screen.
POSITION
Displays the current position.
112 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 113
Remote Controller
TV (TV mode)
TV (TV mode)
Switching Band/Video
It switches between the station of the TV
band to receive and video input.
Channel Selection
The TV channel to receive is selected.
Direct tuning
(NTSC TV type only)
Press this key first, and then specify the
station to receive with the numeric keypad.
Example: In case of Channel 6 (2-digit)
0
6
MNO
«
or
Numeric keypad
• The number of the memorized station is
selected. (
1
–
6
MNO )
• Press the direct tuning key first, then
specify the channel of the station to
receive.
3 End initial setup
⁄
• The settings above can be changed in <Setup
Menu> (page 78).
Initial Setup
Initial Setup
1 Turns the power On
2 Set each item
[Language] Select the language used
for the control screen and setting items.
(page 80)
[Angle] You can adjust the position of
the monitor. (page 82)
[iPod AV Interface Use] Sets the
terminal which the iPod is connected
to. ( "iPod")
[Color] Sets the screen and button
illumination color. (page 86)
[EXT SW] Setting up external switch
power mode. (page 83)
[Camera] You can set Camera
parameters. See <Camera Setup> (page
92).
When pressing the Reset button or turning on the unit for the first time, the Initial SETUP
screen is displayed.
Initial Setup
114 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 115
Source
Display Overview
iPod
"MUSIC" Identifies the music file.
"VIDEO" Identifies the video file.
"RDM" Indicates that the Random function is ON.
"A-RDM" Indicates that the Album random function is ON.
"REP" Indicates that the Repeat function is ON.
Tuner
"AF" Indicates that the AF search function is ON.
"AUTO1" Indicates that Seek mode is set to Auto1.
"AUTO2" Indicates that Seek mode is set to Auto2.
"CRSC" Indicates that the CRSC function is OFF.
"MANU" Indicates that Seek mode is set to Manual.
"RDS" Indicates the state of the RDS station when the
AF function is ON. (White: RDS is being received.
Orange: RDS is not being received.)
"ST" Indicates that stereo broadcast is being received.
"TI" Indicates the reception state of traffic information.
(Orange: TP is being received. White: TP is not
being received.)
HD Radio
"AUTO1" Indicates that Seek mode is set to Auto1.
"AUTO2" Indicates that Seek mode is set to Auto2.
"MANU" Indicates that Seek mode is set to Manual.
"HD" Indicates that HD Radio station is being received.
"M/S" Indicates whether the reception channel is
main or sub. (Orange: Sub channel White: Main
channel)
"ANALOG" Indicates that analog broadcast is being received.
"DIGITAL" Indicates that digital broadcast is being received.
"ST" Indicates that stereo broadcast is being received.
"TAG" Indicates that Tagging is enabled.
SIRIUS/
XM
"SCN" Indicates that the channel scan function is ON.
"SEEK1" Indicates that Seek mode is set to 1.
"SEEK2" Indicates that Seek mode is set to 2.
TV
"AUTO1" Indicates that Seek mode is set to Auto1.
"AUTO2" Indicates that Seek mode is set to Auto2.
"MANU" Indicates that Seek mode is set to Manual.
Shown below is a list of indicators
displayed on the Status bar.
Source
Display Overview
General
"ATT" Indicates that the attenuator is active.
"DUAL" Turns on the Dual zone function.
"LOUD" Indicates that the Loudness control function is ON.
"TEL" Indicates the connection state of the Bluetooth
hands-free unit. (White: Connected. Orange:
Not connected.)
DVD/CD
"FO-REP" Indicates that the Folder repeat function is ON.
"IN" Indicates that a disc is inserted. (White: A Disc is
inside the unit. Orange: Error at the disc player.)
"MOVIE" Identifies the video file.
"MUSIC" Identifies the music file.
"RDM" Indicates that the Random function is ON.
"REP" Indicates that the Repeat function is ON.
DVD-
Video
"C-REP" Indicates that the Chapter repeat function is ON.
"T-REP" Indicates that the Title repeat function is ON.
VCD
"1chLL" Identifies the left audio output of channel 1.
"1chLR" Identifies the monaural audio output of channel
1.
"1chRR" Identifies the right audio output of channel 1.
"1chST" Identifies the stereo audio output of channel 1.
"LL" Identifies the left audio output.
"LR" Identifies the monaural audio output.
"RR" Identifies the right audio output.
"ST" Identifies the stereo audio output.
"PBC" Indicates that the PBC function is ON.
"SVCD" Identifies the Super Video CD.
"VER1" Indicates that the Video CD version is 1.
"VER2" Indicates that the Video CD version is 2.
"REP" Indicates that the Repeat function is ON.
USB
"FO-REP" Indicates that the Folder repeat function is ON.
"MOVIE" Identifies the video file.
"MUSIC" Identifies the music file.
"PICTURE" Identifies the image file.
"RDM" Indicates that the Random function is ON.
"REP" Identifies that the Repeat function is ON.
"PLST" Indicates that the Play list mode is selected now.
Status bar Indicator items DVD Language Codes
Code Language
aa Afar
ab Abkhazian
af Afrikaans
am Amharic
ar Arabic
as Assamese
ay Aymara
az Azerbaijani
ba Bashkir
be Byelorussian
bg Bulgarian
bh Bihari
bi Bislama
bn Bengali, Bangla
bo Tibetan
br Breton
ca Catalan
co Corsican
cs Czech
cy Welsh
da Danish
de German
dz Bhutani
el Greek
en English
eo Esperanto
es Spanish
et Estonian
eu Basque
fa Persian
fi Finnish
fj Fiji
fo Faroese
fr French
fy Frisian
ga Irish
gd Scots Gaelic
gli Galician
gn Guarani
gu Gujarati
ha Hausa
he Hebrew
hi Hindi
hr Croatian
hu Hungarian
hy Armenian
ia Interlingua
Code Language
ie Interlingue
ik Inupiak
id Indonesian
is Icelandic
it Italian
ja Japanese
jv Javanese
ka Georgian
kk Kazakh
kl Greenlandic
km Cambodian
kn Kannada
ko Korean
ks Kashmiri
ku Kurdish
ky Kirghiz
la Latin
lb Luxembourgish
ln Lingala
lo Laotian
lt Lithuanian
lv Latvian, Lettish
mg Malagasy
mi Maori
mk Macedonian
ml Malayalam
mn Mongolian
mo Moldavian
mr Marathi
ms Malay
mt Maltese
my Burmese
na Nauru
ne Nepali
nl Dutch
no Norwegian
oc Occitan
om (Afan) Oromo
or Oriya
pa Punjabi
pl Polish
ps Pashto, Pushto
pt Portuguese
qu Quechua
rm Rhaeto-Romance
rn Kirundi
ro Romanian
Code Language
ru Russian
rw Kinyarwanda
sa Sanskrit
sd Sindhi
sg Sangho
sh Serbo-Croatian
si Singhalese
sk Slovak
sl Slovenian
sm Samoan
sn Shona
so Somali
sq Albanian
sr Serbian
ss Siswati
st Sesotho
su Sundanese
sv Swedish
sw Swahili
ta Tamil
te Telugu
tg Tajik
th Thai
ti Tigrinya
tk Turkmen
tl Tagalog
tn Setswana
to Tongan
tr Turkish
ts Tsonga
tt Tatar
tw Twi
uk Ukrainian
ur Urdu
uz Uzbek
vi Vietnamese
vo Volapuk
wo Wolof
xh Xhosa
yo Yoruba
zh Chinese
zu Zulu
116 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 117
Next page 3Next page 3
Help? Troubleshooting
Some functions of this unit may be disabled
by some settings made on this unit.
! • Cannot set up the subwoofer.
• Cannot set up subwoofer phase.
• No output from the subwoofer.
• Cannot set up the low pass filter.
• Cannot set up the high pass filter.
▲
Subwoofer is not set to On.
☞ <Speaker Setup> (page 94)
▲
The Dual zone function is enabled.
☞ <Zone Control> (page 74)
! • Cannot select the output destination of
the subsource in the Dual zone.
• Cannot adjust the volume of the rear
speakers.
▲
The Dual zone function is disabled.
☞ <Zone Control> (page 74)
! Cannot play audio files.
▲
"CD Read" of <Disc Setup> (page 100) is set to
"2".
! Cannot Folder select.
▲
The Random play function is enabled.
! Cannot perform Repeat play.
▲
The PBC function of the Video CD is
enabled.
! • Cannot set up the equalizer.
• Cannot set up the crossover network.
▲
The Dual zone function is enabled.
☞ <Zone Control> (page 74)
▲
The DSP Select is Bypass.
☞ <DSP Bypass Control> (page 93)
What might seem to be a malfunction in
your unit may just be the result of slight
misoperation or miswiring. Before calling
service, first check the following table for
possible problems.
General
? The Touch Sensor Tone doesn’t sound.
✔ The preout jack is being used.
☞ The Touch Sensor Tone can’t be output from
the preout jack.
Tuner source
? Radio reception is poor.
✔ The car antenna is not extended.
☞ Pull the antenna out all the way.
✔ The antenna control wire is not connected.
☞ Connect the wire correctly, referring to the
section on <INSTALLATION MANUAL>.
Disc source
? The specified disc does not play, but
another one plays instead.
✔ The specified CD is quite dirty.
☞ Clean the CD.
✔ The disc is severely scratched.
☞ Try another disc instead.
Audio file source
? The sound skips when an Audio file is
being played.
✔ The media is scratched or dirty.
☞ Clean the media, referring to the CD
cleaning of the section on <Handling discs>
(page 4).
✔ The recording condition is bad.
☞ Record the media again or use another
media.
Help? Error
When the unit fails to operate correctly,
the cause of the failure appears on the
display.
"Protect" :
Protective circuit has been activated because
a speaker cord has shorted or it has come in
contact with the car chassis.
➡ Wire or insulate the speaker cord as
appropriate and then push the Reset
button.
"Hot Error" :
When the internal temperature of this unit
rises to 60°C or more, the protection circuit is
activated and you may not be able to operate
the unit. At such times this message will
appear.
➡ Use the unit again after reducing the
temperature inside the vehicle.
"Hold Error" :
Activation of the protective circuit when the
temperature inside the disc changer is higher
than 60 degrees Celsius stops the disc changer
from operating. At such times this message
will appear.
➡ Use when the temperature at the site
where the disc changer has been fitted has
dropped.
"Mecha Error" :
The disc player is malfunctioning.
➡ Eject the disc and try inserting it again.
Contact the Kenwood dealer if this indicator
continues blinking or the disc cannot be
ejected.
"Disc Error" :
An unplayable disc is inserted.
"Read Error" :
Disc is quite dirty.
➡ Clean the disc, referring tot he section on
<Handling discs> (page 4).
Disc is upside down.
➡ Load the disc with the labeled side up.
"Region code Error" :
The disc you wanted to play has a region code
that cannot be played with this unit.
"Parental level Error" :
The disc you wanted to play has a higher level
than the parental level you set.
"Error 07–67" :
The unit is not operating correctly due to
some reason or other.
➡ Push the unit's Reset button. If the "Error
07−67" message does not disappear, see
your nearest Kenwood dealer.
"No Device" (USB device):
The USB device is selected as a source
although no USB device is connected.
➡ Change the source to any source other
than USB/iPod. Connect an USB device, and
change the source to USB again.
"Disconnected" (iPod, Bluetooth audio
player):
The iPod/Bluetooth audio player is selected
as a source although no iPod/Bluetooth audio
player is connected.
➡ Change the source to any source other than
iPod/Bluetooth. Connect an iPod/Bluetooth
audio player, and change the source to
iPod/Bluetooth again.
"No Music" :
The connected USB device contains no
playable audio file.
Media was played that doesn’t have data
recorded that the unit can play.
"USB Device Error!!" :
The connected USB device is rated a current
capacity higher than the allowable limit.
➡ Check the USB device.
Some trouble may have occurred to the
connected USB device.
➡ Change the source to any source other than
USB. Remove the USB device.
118 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 119
Next page 3
"Authorization Error" :
Connection to the iPod has failed.
➡ Remove the iPod and then reconnect it.
The unit does not support the iPod.
➡ Refer to <iPod/iPhone that can be
connected to this unit> (page 7).
"Update your iPod" :
The iPod's software is an older version which
the unit can not support.
➡ Confirm that the software for the iPod is the
latest version. Refer to <iPod/iPhone that
can be connected to this unit> (page 7).
"You only can connect one iPod." :
More than one iPod are connected to this unit.
➡ Connect only one iPod to the USB terminal
with iPod tag.
"Update your USB database" :
The USB device is different from the previous
one or the contained audio files are replaced.
➡ Update your database. Refer to <Source
Control Screen> (page 26) of USB Device
Control.
"Navigation Error. Please turn on power
again later." (DNX series only) :
The communication error has occurred due to
severely cold temperature.
➡ Turn on power again after warming your car
interior.
"No Navigation" (DDX series only):
This unit does not support the connected
navigation unit.
➡ The latest information on the connectable
navigation unit can be obtained from
http://www.kenwood.com/cs/ce.
No navigation unit is connected.
➡ Connect a supported navigation unit.
"CHECK SIRIUS" :
The unit cannot recognize the connected
SIRIUS Tuner Box.
➡ Check the connection of the SIRIUS Tuner
Box.
"ANTENNA ERROR" :
Something is wrong with the antenna.
➡ Check the connection of the antenna.
"ACQUIRING SIGNAL" :
The unit cannot receive any signal.
➡ Move the vehicle to the area where the unit
can receive signal.
"FIRMWARE UPDATING" :
Updating the firmware of SIRIUS tuner.
➡ Operation is invalid until the update is
completed.
"CHANNELS UPDATING **% COMPLETE" :
Updating the SIRIUS Channel Map.
➡ Operation is invalid until the update is
completed.
"SUBSCRIPTION UPDATED" :
Updating the subscription information.
➡ Operation is invalid until the update is
completed.
"INVALID CHANNEL" :
The selected channel is invalid.
➡ Select a different channel.
"CALL 888-539-SIRIUS TO SUBSCRIBE" :
The selected channel is not subscribed.
➡ Call the displayed number for subscription.
"Check XM Tuner" :
The unit cannot recognize the connected XM
Tuner.
➡ Check the connection of the XM Tuner.
"No Signal" :
The unit cannot receive any signal.
➡ Check the connection of the antenna.
"Check Antenna" :
Something is wrong with the antenna.
➡ Check the connection of the antenna.
"Ch Unavailable" :
The selected channel is invalid.
➡ Select a different channel.
"Ch Unauthorized" :
The selected channel is not subscribed.
"Channel Off Air" :
The broadcast of the selected channel has
finished.
Help? Error Specifications
Monitor section
Monitor section
Picture Size
: 6.95 inches (diagonal) wide
: 156.6 mm (W) x 81.6 mm (H)
Display System
: Transparent TN LCD panel
Drive System
: TFT active matrix system
Number of Pixels
: 1,152,000 (800H x 480V x RGB)
Effective Pixels
: 99.99 %
Pixel Arrangement
: RGB striped arrangement
Back Lighting
: LED
DVD player section
DVD player section
D/A Converter
: 24 bit
Audio Decoder
: Linear PCM/ Dolby Digital/ dts/ MP3/ WMA/
AAC
Video Decoder
: MPEG1/ MPEG2
: DivX (DNX9/ DDX8 series)
Wow & Flutter
: Below Measurable Limit
Frequency Response
DNX9/ DDX8 series
Sampling frequency;
96 kHz : 20 – 22,000 Hz
48 kHz : 20 – 22,000 Hz
44.1 kHz : 20 – 20,000 Hz
DNX7 series
Sampling frequency;
96 kHz : 20 – 20,000 Hz
48 kHz : 20 – 20,000 Hz
44.1 kHz : 20 – 20,000 Hz
Total Harmonic Distortion
: 0.008 % (1 kHz)
S/N Ratio (dB)
: 98 dB (DVD-Video 96 kHz)
Dynamic Range
: 98 dB (DVD-Video 96 kHz)
Disc Format
: DVD-Video/ VIDEO-CD/ CD-DA
Sampling Frequency
: 44.1/ 48/ 96 kHz
Quantifying Bit Number
: 16/ 20/ 24 bit
USB interface section
USB interface section
USB Standard
: USB 2.0 High speed
iPod: USB 1.1 Full speed (DNX9/ DDX8 series
only)
File System
: FAT 16/ 32
Maximum Power Supply Current
: 500 mA
D/A Converter
: 24 Bit
Video Decoder
: MPEG1/ MPEG2/ MPEG4/ H.264/ WMV
Audio Decoder
: MP3/ WMA/ AAC/ WAV (Linear PCM)
Bluetooth section
Bluetooth section
Technology
: Bluetooth Ver.2.1 + EDR Certified
Frequency
: 2.402 – 2.480 GHz
Output Power
: +4dBm (MAX), 0dBm (AVE), Power Class2
Maximum Communication range
: Line of sight approx. 10m (32.8 ft)
Profile
HFP (Hands Free Profile),
SPP (Serial Port Profile),
HSP (Headset Profile),
OPP (Object Push Profile),
PBAP (Phonebook Access Profile),
SYNC (Synchronization Profile),
A2DP (Advanced Audio Distribution Profile),
AVRCP (Audio/Video Remote Control Profile)
120 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 121
Video section
Video section
Color System of External Video Input
: NTSC
External Video Input Level (mini jack)
: 1 Vp-p/ 75 Ω
External Audio Max Input Level (mini jack)
: 2 V/ 25 kΩ
Video Output Level (RCA jacks)
: 1 Vp-p/ 75 Ω
Audio Output Level (RCA jacks)
: 1.2 V/ 10 kΩ
Analog RGB input (DDX series only)
: 0.7 Vp-p/ 75 Ω
Audio section
Audio section
Maximum Power (Front & Rear)
: 50 W x 4
Full Bandwidth Power (Front & Rear)
(4 Ω, 14.4 V, 1 % THD)
: 22 W x 4
Preout Level (V)
: 5 V/ 10 kΩ (DNX9/ DDX8 series)
: 2 V/ 10 kΩ (DNX7 series)
Preout Impedance
: 80 Ω (DNX9/ DDX8 series)
: ≤ 600 Ω (DNX7 series)
Speaker Impedance
: 4 – 8 Ω
FM tuner section
FM tuner section
Frequency Range
200 kHz : 87.9 MHz – 107.9 MHz (DNX9960/
DNX7160/ DNX7020EX/ DDX896)
50 kHz : 87.5 MHz – 108.0 MHz (DDX8046BT)
Usable Sensitivity (S/N :30 dB)
: 9.3 dBf (0.8 μV/ 75 Ω)
Quieting Sensitivity (S/N :50 dB)
: 15.2 dBf (1.6 μV/ 75 Ω)
Frequency Response (± 3.0 dB)
: 30 Hz – 15 kHz
S/N Ratio (dB)
: 70 dB (MONO)
Selectivity (± 400 kHz)
: ≥ 80 dB
Stereo Separation
: 35 dB (1 kHz)
AM tuner section
AM tuner section
Frequency Range (10 kHz)
: 530 kHz – 1700 kHz
Usable Sensitivity
: 28 dBμ
Specifications
DSP Section
DSP Section
Graphics equalizer
DNX9/ DDX8 series
Band: 13 Band
Frequency (BAND1 – 13)
: 62.5/ 100/ 160/ 250/ 400/ 630/ 1k/ 1.6k/
2.5k/ 4k/ 6.3k/ 10k/ 16k Hz
Channel: Front/ Rear/ Center
DNX7/ DDX7 series
Band: 5 Band
Frequency (BAND1 – 5)
: 62.5/ 250/ 1k/ 4k/ 16k Hz
Gain
: -9/ -8/ -7/ -6/ -5/ -4/ -3/ -2/ -1/ 0/ 1/ 2/ 3/ 4/
5/ 6/ 7/ 8/ 9 dB
X'over
High pass filter
Frequency: Through, 30/ 40/ 50/ 60/ 70/ 80/
90/ 100/ 120/ 150/ 180/ 220/
250 Hz
Slope: -6/ -12/ -18/ -24 dB
Low pass filter
Frequency: 30/ 40/ 50/ 60/ 70/ 80/ 90/ 100/
120/ 150/ 180/ 220/ 250 Hz,
Through
Slope: -6/ -12/ -18/ -24 dB
Time alignment
Front/ Rear/ Subwoofer
: 0 – 20.01 ft (0.07 ft Step)
Center: 0 – 11.15 ft (0.07 ft Step) (DNX9/
DDX8 series)
Position
: 0 – 5.68 ft (0.07 ft Step)
Channel Level (DNX9/ DDX8 series)
: ± 10 dB
Navigation section (DNX series
Navigation section (DNX series
only)
only)
Receiver
: High-sensitivity GPS receiver
Reception Frequency
: 1575.42 MHz (C/A code)
Acquisition Times
Cold : < 38 seconds
Factory Reset : < 45 seconds
(On average for a stationary receiver with a
clear view of the sky)
Accuracy
Position : < 10 meters typical
Velocity : 0.05 m/sec. RMS
Position Method
: GPS
Antenna
: External GPS antenna
External SW
External SW
Maximum Power Supply Current
: 500 mA
General
General
Operating voltage
: 14.4 V (10.5 – 16 V allowable)
Maximum Current Consumption
: 15 A
Dimensions (W × H × D)
: 181.7 × 100.0 × 180 mm
7-3/16 x 3-15/16 x 7-1/8 inch
Operational Temperature Range
: -10 °C – +60 °C
Storage Temperature Range
: -20 °C – +85 °C
Weight
DNX9 series : 2.54 kg (5.6 lbs)
DNX7 series : 2.50 kg (5.5 lbs)
DDX series : 2.48 kg (5.5 lbs)
Although the effective pixels for the liquid crystal
panel is given as 99.99% or more, 0.01% of pixels
may not light or may light incorrectly. Specifications subject to change without notice.
is a trademark of SRS Labs, Inc.
WOW technology is incorporated under license from SRS Labs, Inc.
is a trademark of DVD Format/Logo Licensing Corporation registered in the U.S., Japan and other
countries.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended
for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering
or disassembly is prohibited.
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S.
and worldwide patents issued & pending. DTS and the Symbol are registered trademarks & DTS 2.0 Channel and
the DTS logos are trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.
The "AAC" logo is a trademark of Dolby Laboratories.
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Kenwood
Corporation is under license. Other trademarks and trade names are those of their respective owners.
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
iPhone is a trademark of Apple Inc.
iTunes is a trademark of Apple Inc.
“Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has
been certified by the developer to meet Apple performance standards.
“Works with iPhone” means that an electronic accessory has been designed to connect specifically to iPhone
and has been certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
HD Radio™ and the HD Radio Ready logo are proprietary trademarks of iBiquity Digital Corporation.
ABOUT DIVX VIDEO:
DivX® is a digital video format created by DivX, Inc. This is an official DivX Certified device that
plays DivX video. Visit www.divx.com for more information and software tools to convert your files
into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND:
This DivX Certified® device must be registered in order to play DivX Video-on-Demand (VOD)
content. To generate the registration code, locate the DivX VOD section in the device setup menu.
Go to vod.divx.com with this code to complete the registration process and learn more about
DivX VOD.
DivX®, DivX Certified® and associated logos are registered trademarks of DivX, Inc. and are used under license.
Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S.
and worldwide patents issued & pending. DTS and the Symbol are registered trademarks & DTS Digital Surround
and the DTS logos are trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.
DNX9960/ DDX896/ DDX8046BT:
DNX7160/ DNX7020EX:
FCC WARNING
This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless
the modifications are expressly approved in the
instruction manual. The user could lose the authority to
operate this equipment if an unauthorized change or
modification is made.
NOTE
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment may cause harmful interference to
radio communications, if it is not installed and used
in accordance with the instructions. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
DNX9960/ DNX7160/ DNX7020EX/ DDX896:
IC (Industry Canada) Notice
Operation is subject to the following two
conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause
undesired operation of the device.
The term "IC: " before the certification/
registration number only signifies that the
Industry Canada technical specification were
met.
This product contains a CR Coin Cell Lithium
Battery which contains Perchlorate Material
– special handling may apply. See www.dtsc.
ca.gov/hazardouswaste/perchlorate
DDX8046BT:
The marking of products using lasers
CLASS 1
LASER PRODUCT
The label is attached to the chassis/case and
says that the component uses laser beams that
have been classified as Class 1. It means that the
unit is utilizing laser beams that are of a weaker
class. There is no danger of hazardous radiation
outside the unit.
DNX9960/ DNX7160/ DNX7020EX/ DDX896:
2CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
In compliance with Federal Regulations, following
are reproductions of labels on, or inside the product
relating to laser product safety.
Kenwood Corporation
2967-3, ISHIKAWA-MACHI,
HACHIOJI-SHI
TOKYO, JAPAN
KENWOOD CORP. CERTIFIES THIS EQUIPMENT
CONFORMS TO DHHS REGULATIONS N0.21 CFR
1040. 10, CHAPTER 1, SUBCHAPTER J.
Location : Bottom Panel
This symbol mark indicates that
Kenwood manufactured this
product so as to decrease harmful
infl uence on the environment.

Navigation menu