JVC KENWOOD 39622B GPS NAVIGATION SYSTEM User Manual

JVC KENWOOD Corporation GPS NAVIGATION SYSTEM

Contents

User manual 2 of 2

72 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 73Next page 3Next page 3reduced the volume using the "Volume Offset", the sound generated if you suddenly switch to another source may be extremely loud.[Subwoofer Level] Adjusts the subwoofer volume.The setting is available when subwoofer is set to any item other than "None". See <Speaker Setup> (page 94).[Bass Boost] Sets the amount of bass boost. (DNX7 series only)"OFF"/ "Step1"/ "Step2"[Supreme] Turns ON/OFF the Supreme function. (DNX9/ DDX8 series only)Technology to extrapolate and supplement with proprietary algorithm, the high-frequency range that is cut off when encoding. This function works on DVD, USB, SD and iPod sources. Equalizer Control Equalizer ControlYou can set up the equalizer.1 Display the Equalizer screenTouch [ ] > > [ ] > > [Equalizer]. (page 72)2 Select EQ curves[Natural], [Rock], [Pops], [Easy], [Top40], [Jazz], [Game], [iPod], [User] Selects an equalizer curve type.You can select any of the following equalizer curves.⁄• [iPod]During iPod source only.[EQ] Displays the Graphic Equalizer setup screen. (page 73) Graphic Equalizer Setup Graphic Equalizer SetupYou can Manually set the equalizer curve.1 Display the Equalizer screenTouch [ ] > > [ ] > > [Equalizer]. (page 72)2 Display the Graphic Equalizer screen⁄• When "iPod" is selected in <Equalizer Control>, the [EQ] button is deactivated. "iPod" uses its equalizer function.3 Select the channel to be adjusted(DNX9/ DDX8 series only)[F] Front speaker[R] Rear speaker[C] Center speaker Audio Control Menu Audio Control MenuDisplays the Audio Control menu to set the sound effect function of this unit.1 Display the Source Select ScreenWhen a video screen is displayed, press the [SRC] button.2 Display the Audio Control menuIn this manual, the above selection is indicated as: Touch [ ] > > [ ]. 3 Select the Audio Control itemItem Page[Audio Control] 72[Equalizer] 73[EQ] 73[Zone Control] 74[SRS WOW] 76[Space Enhancer] 75Audio ControlItem Page[Position] 75[Surround Control] 77 Audio Control Audio ControlYou can adjust the front/rear and right/left audio balance.1 Display the Audio Control screenTouch [ ] > > [ ] > > [Audio Control]. (page 72)2 Set each itemDNX9/ DDX8 series111DNX7 series1111 Adjusts the front/back and left/right volume around the touched area. [2], [3] Adjusts the right and left volume balance.[5], [∞] Adjusts the front and rear volume balance.[Volume Offset] Finely adjust the volume of the current source to minimize the difference in volume between different sources. ⁄• If you have increased the volume first, then
74 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 75Next page 3Next page 3⁄• There are following limitations when zone function is set to "ON".- There is no output from the subwoofer or center speaker.- "Bass Boost" of <Audio Control> (page 72) is not available.- <Equalizer Control> (page 73), <Space Enhancer> (page 75), <Listening Position> (page 75), <SRS WOW Control> (page 76), and <Surround Control> (page 77) are not available.- <DSP Bypass Control> (page 93), <Speaker Setup> (page 94), <Car Type (DTA) Setup> (page 95), and <Channel Level> (page 97) are not available. Space Enhancer (DNX7 series) Space Enhancer (DNX7 series)You can enhance the soundscape.1 Display the Space Enhancer screenTouch [ ] > > [ ] > > [Space Enhancer]. (page 72)2 Set the Space Enhancer1111 Sets the soundscape level. ⁄• You cannot set Space Enhancer in tuner source. Listening Position Listening PositionYou can adjust the sound effects according to your listening position.1 Display the Position screenTouch [ ] > > [ ] > > [Position]. (page 72)2 Set the Position Control[P1] - [P3] Stores the present adjustment setup in memory, or recalls it from memory.To store your adjustment in memory:Continue to touch [P1] to [P3] more than 2 seconds.To call your adjustment from memory:Touch [P1] to [P3] of your adjustment you wish to recall from memory.[2], [3] Sets a listening position.You can select any of "Front R" (Right front), "Front L" (Left front), "Front All" (All front), "All" (All), and "User" (User) positions.[DTA] Displays the Position DTA (Digital Time Alignment) screen.3 Exit Position Control⁄• The final distance is adjusted to the total of Car Type Set Up value (page 95) and Position Setup (both Position and Position DTA) value.• If you change the Car Type Set Up value (page 95), the position is set to "All". Zone Control Zone ControlYou can set the front and rear audio source.1 Display the Zone Control screenTouch [ ] > > [ ] > > [Zone Control]. (page 72)2 Set the Zone Control[Single Zone] Sets the unit to single zone.[Dual Zone] Sets the unit to dual zone.[Front Source] Sets the front audio source.[Rear Source] Sets the rear audio source.⁄• When the rear speaker sound is switched, the audio source that is output at the AV OUTPUT terminal is also switched to the same source.[Rear VOL.] Adjusts the volume of the rear channel.4 Set the Graphic EqualizerDNX9/ DDX8 series111DNX7 series1111 Gain level can be adjusted by touching the each frequency bar.[2], [3] Sets a frequency.[5], [∞] Sets a gain level.[EQ Init] Returns to the previous level which the gain level is adjusted.[Flat] Tone curve becomes flat.[Bass EXT] Bass Extend settings. When turned on, the frequency lower than 62.5 Hz is set to the same gain level as 62.5Hz. [SW Level] Adjusts the subwoofer volume.The setting is available when subwoofer is set to any item other than "None". See <Speaker Setup> (page 94).Audio Control
76 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 77⁄• FOCUS: Adjusts the vertical position of the speaker and sound image by virtual adjustment. • TruBass: Assists the playback for the super bass sound. • SRS 3D: Makes a natural 3D sound field. • Some items cannot be adjusted depending on the selected speaker.• SRS WOW control is not available in tuner source, TV source and HD Radio source.• When Surround Control is Dolby Pro Logic II, SRS WOW control is not available. Surround Control Surround Control(DNX9/ DDX8 series)(DNX9/ DDX8 series)You can set up the sound field.1 Display the Surround Control screenTouch [ ] > > [ ] > > [Surround Control]. (page 72)2 Set the Surround Control1111 Sets a sound field.You can select any of the following sound fields."Bypass"/ "Bypass+Center"/ "Dolby Pro Logic II Movie"/ "Dolby Pro Logic II Music"/ "Dolby Pro Logic II Matrix"[Stream Information] Displays the present source information. The stream (Dolby Digital, dts, Linear PCM, MPEG, SDDS, AAC or MP3/WMA), input channels (front or rear channels), and sampling frequency are displayed.⁄• When you have selected the TV or TUNER source and when you set the Dolby PL, we recommend you to select the "Dolby PLII Matrix" mode. If you select another Dolby PLII mode, the sound is NOT output from rear speakers when you receive monaural broadcasting sounds.• Surround control can be set for each source. Dolby Pro Logic II Music Adjustment1 Display the Dolby Pro Logic II Music Adjust screen2 Adjust the sound field[Dimension Control] Sets the surround position by adjusting the front and rear volume balance.[Center Width Control] Sets the vocal image position by adjusting the right and left vocal volume level.[Panorama Mode] Turns the Panorama mode On or Off.⁄• You cannot use the <Surround Control Adjustment> during playback of a Multi-channel source.• Only the adjusted distance of position setup (Position and Position DTA values) is stored in memory. Therefore, the final adjustment distance changes if you change the Car Type Set Up value (page 95).Position DTA ControlYou can fine-adjust your listening position.1 Display the Position DTA screen2 Select a speaker you wish to adjust3332221116664441 Center speaker (DNX9/ DDX8 series)2 Left front speaker3 Right front speaker4 Left rear speaker5 Right rear speaker6 Subwoofer[2], [3] Finely adjusts the value set with the Position function.[Total DTA] Indicates setup distance. The adjusted distance (Position and Position DTA values), and the total of the distance adjusted by Car Type Set Up (page 95) and the adjustment distance for position setup are indicated.3 Finely adjust the distanceFinely adjust the value set with the Position function. SRS WOW Control SRS WOW Control(DNX9/ DDX8 series)(DNX9/ DDX8 series)You can set up the SRS WOW effect.1 Display the SRS WOW Control screenTouch [ ] > > [ ] > > [SRS WOW]. (page 72)2 Set the SRS WOW Control1111 Selects SRS WOW setting.SRS WOW User Setup1 Display the SRS WOW Adjust screen2 Adjust the SRS settings1111 Selects a speaker to be set (Front, Rear or Center speaker).[TruBass] Sets the TruBass effect level.[FOCUS] Sets the FOCUS effect level.[SRS 3D] Sets the SRS 3D effect level.Audio Control
78 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 79Next page 3Next page 3 DivX Setup (DNX9/ DDX8 series) DivX Setup (DNX9/ DDX8 series)Checks the registration code. This code is needed when making a disc which has DRM (Digital Rights Management).1 Display the DivX Setup screenTouch [ ] > > [ ] > > [DivX(R) SETUP]. (page 78)Displays the registration code.⁄• Disabled when a DVD is being played.• When downloading a DivX VOD file controlled by DRM, register the code appeared on the screen such as the one above. Otherwise the file may not be able to play with this unit. Remaining number of viewing is displayed when playing a DivX VOD file with the viewing restriction. When the remaining number of viewing reached 0, a warning message appears and the file cannot be played.Deactivating DivX Code1 Display the DivX Deactivation Confirm screen2 Cancel the registrationTouching the screen displays a confirmation message. Touch [OK]. To cancel clearing, touch [Cancel]. Software Information Software InformationChecks the software version of this unit.1 Display the Software Information screenTouch [ ] > > [ ] > > [Software]. (page 78)Displays the software version.⁄• For how to update the software, refer to the relevant update procedure manual which comes with the software. Setup Menu How to Display SETUP Menu Screen How to Display SETUP Menu ScreenDisplays the Setup menu to set various functions.1 Display the Source Select ScreenWhen a video screen is displayed, press the [SRC] button.2 Display the Setup Menu ScreenIn this manual, the above selection is indicated as: Touch [ ] > > [ ]. 3 Select the setup item⁄• [AV-IN SETUP], [Navigation] and [Audio SETUP] options can be locked. The key mark ( ) is displayed in reverse video for the locked option. You can set up various receiver parameters.See <Setup Memory> (page 84). Item Page[DivX(R) SETUP] 79[System][User Interface] 80[Touch] 81[Clock] 82[Security] 82[Angle] 82[EXT SW] 83[SETUP Memory] 84[Display][Screen Control] 87[Color] 86[Background] 85[Bluetooth SETUP] 88[SIRIUS SETUP] 102[DVD SETUP] 98[iPod SETUP] 101[USB SETUP] 101[SD SETUP] 101[TV SETUP] 101[AV-IN SETUP] 91[Navigation] 93[Software] 79[Audio SETUP] 93[Speaker Select] 94[Car Type] 95[Channel Level] 97[AV-OUT Interface] 91[Camera SETUP] 92
80 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 81Next page 3Next page 3[Cancel] Cancels the selected language. When [ASR] is set to "Disabled" (DNX9 only)When [Select Mode] is set to "Advanced"[GUI Language Select] Selects the display language used for the control screen and so forth. ( "American English (en)") [Navigation Language Select] Selects the language used for navigation. ( "American English (en)") (DNX7 series only)[User Text Language Select] Selects the language used for tag text (song information). ( "American English (en)") Touch Panel Adjustment Touch Panel AdjustmentYou can adjust the touch panel operations.1 Display the Touch panel Adjustment screenTouch [ ] > > [ ] > > [System] > > [Touch]. (page 78)2 Adjust the Touch panelFollow the instruction on the screen and touch the center of .[Cancel] Cancels the Touch Panel Adjust.[Reset] Resets to the initial status.Setup Menudisplay off."CAM": Press the [AUD] button for longer than 1 second to switch to camera view.[Animation] Sets whether to display animation. ( "ON") Language Setting Language SettingYou can select the display language for the control screen and audio file tags. 1 Display the User Interface screenTouch [ ] > > [ ] > > [System] > > [User Interface]. (page 78)2 Display the Language Setting screen3 Select a language[ASR] Selects whether to use the voice control function. (page 56) ( "Enabled") (DNX9960 only)"Enabled": Voice control is activated."Disabled": Voice control is deactivated.[Select Mode] Selects the mode to select a language. ( "Easy") Touching [Advanced] allows you to select languages for respective items. [Language Select] Selects a language. ( "American English (en)") [Enter] Determines the selected language. User Interface User InterfaceYou can setup user interface parameters.1 Display the User Interface screenTouch [ ] > > [ ] > > [System] > > [User Interface]. (page 78)2 Set each item[Beep] Turns the key touch tone On or Off. ( "ON") [Remote Sensor] Selects a remote control signal. ( "ON")When turned "OFF", the remote control of TV reception is rejected.[Language] Select the language used for the control screen and setting items. See <Language Setting> (page 80).[Scroll] Allows scrolling of text display on the Source Control screen. ( "Manual")"Auto": Scrolls the screen automatically."Manual": Allows you to scroll the screen manually.[Drawer Close] Sets whether to close the function bar automatically. ( "Auto")[AUD Key Longer than 1 Second] Sets the function of the [AUD] button. (page 12)"V.OFF": Press the [AUD] button for longer than 1 second to turn the
82 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 83Next page 3Next page 3 EXT SW Setup EXT SW SetupSets up the exteral switch power mode.1 Display the EXT SW screenTouch [ ] > > [ ] > > [System] > > [EXT SW]. (page 78)2 Perform EXT SW Setup[SW1 Name]/ [SW2 Name] Sets the name of the external device. See <How To Use the Character Entry Screen> (page 83) for information on how to enter a name.[Output Pattern] Sets the power signal output mode.( EXT SW1: Pulse, EXT SW2: Level)"Pulse": Generates a single power signal pulse."Level": Continues output of high power signal.Sets to turn output on/off each time the button on the EXT SW Control screen is touched. See <External Device Power Supply Control> (page 55).[Pulse Set] Sets the Pulse signal output time. Outputs 500ms when "1" is set. Increases by 200ms with each step. Up to 100 steps can be set. How To Use the Character Entry Screen1111 Enters characters.[2], [3] Shifts the cursor.[5], [∞] Scrolls up or down the character button display.[Shift] Toggles between uppercase and lowercase.[qwe]/ [abc] Sets the key layout of the character buttons.abc : Alphabetical key layout. qwe : Qwerty key layout. [Clear] Clears the character.[Space] Enters a space.If you erase a character, locate the cursor on it and touch this button.⁄• You can enter characters only after you have applied the parking brake.Setup Menu Clock and Date Setup Clock and Date SetupYou can adjust the clock time.1 Display the Clock Setup screenTouch [ ] > > [ ] > > [System] > > [Clock]. (page 78)2 Setup the Clock1111 Adjusts month, day, year, hours, and minute. [Reset] Sets "00" minute.Setup examples: 3:00 – 3:29 \ 3:003:30 – 3:59 \ 4:00 [Synchronize] Sets the clock time in synchronization with the time data sent from the navigation system or the RDS station. ( DNX series: "Navigation", DDX series: "RDS")"OFF"/ "RDS"*1/ "Navigation"When the synchronized mode is set, the clock cannot be adjusted manually. (*1 North American sales area only)3 Adjust the date or clock time Security Setup Security SetupA red indicator will blink on the unit after the ACC is set to OFF, warning potential thieves.1 Display the Security screenTouch [ ] > > [ ] > > [System] > > [Security]. (page 78)2 Setup the SI (Security Indicator)[SI] Turns the SI function on or off.If turned "ON", the security indicator on the front panel flashes when the vehicle ignition is off. ( "ON") Monitor Angle Control Monitor Angle ControlYou can adjust the position of the monitor.1 Display the Angle Setup screenTouch [ ] > > [ ] > > [System] > > [Angle]. (page 78)2 Set the Monitor Angle1111 Sets the Monitor angle.[Off Position] Stores the current monitor angle as the angle during power off.
84 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 85Next page 3Next page 3 Changing Background image Changing Background imageLoads an image from the connected USB device and sets it for the background image.1 Connect the device which has the image to load2 Display the Background screenTouch [ ] > > [ ] > > [Display] > > [Background]. (page 78)3 Change Standby4 Display the Background Memory screen[Change] Selects an image for background. [Delete] Deletes the background image. Touching the screen displays a confirmation message. Touch [Yes]. To cancel clearing, touch [No].5 Select the image to load6 Load the image[] Rotates counter clockwise.[] Rotates clockwise.7 Select Background Change screen8 Select an image for background1111 Returns to the initial background.9 Set the image as the backgroundSetup Menu Setup Memory Setup MemoryAudio Control, AV-IN SETUP, AV Interface, Navigation, and Audio SETUP settings can be memorized. The memorized settings can be recalled at any time. For example, even when the settings are cleared due to replacement of the battery, the settings can be restored.1 Display the SETUP Memory screenTouch [ ] > > [ ] > > [System] > > [SETUP Memory]. (page 78)2 Start Setup Memory[Lock] Locks the AV-IN SETUP, Navigation, and Audio SETUP settings. When [Lock] is selected, you cannot change the AV-IN SETUP, Navigation, and Audio SETUP settings.[Yes] Memorizes or recalls the settings.[No] To cancel the function, touch [No]. To cancel memorization, touch [No].The SETUP Menu screen appears again.3 Select a desired function[Recall] Recalls the memorized settings.[Memory] Memorizes the current settings.[Clear] Clears the currently memorized settings.4 Memorize or recall the settingsWhen memorizing the Audio Setup and AV Interface settings:If settings have already been memorized, a confirmation message appears. Touch [Yes]. To cancel memorization, touch [No].When recalling the memorized settings:Touching the screen displays a confirmation message. Touch [Yes]. To cancel recalling, touch [No]. When clearing the currently memorized settings:Touching the screen displays a confirmation message. Touch [Yes]. To cancel clearing, touch [No]. 5 Quit memorization/recalling of settings
86 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 87Next page 3Next page 3To register your original color1 Start the RGB coordinate2 Adjust each color value1111 Selects a preset number to register.[Red Value] Adjusts the Red value.[Green Value] Adjusts the Green value. [Blue Value] Adjusts the Blue value.3 Select a Preset number to register 2 sec. Adjusted color is registered to the selected Preset button. 4 Complete the color coordination Screen Control Screen ControlYou can adjust the screen mode of the monitor.1 Display the Screen Control screenTouch [ ] > > [ ] > > [Display] > > [Screen Control]. (page 78)2 Set each item[Bright] Brightness Control[Contrast] Contrast Control[Black] Black Level Adjustment[Dimmer] Dimmer Mode Setup( "ON")"ON": The display dims."OFF": The display doesn’t dim."SYNC": Turning the Dimmer function On or Off when the vehicle light control switch is turned On or Off."NAV-SYNC": Turning the Dimmer function On or Off according to the Navigation Day/Night display setting. (DNX series and DDX series with navigation unit only)⁄• In this Screen Control screen, you can perform setups for the menu screen. Setups for videos such as DVD can be performed on the <Screen Control> (page 58).Setup Menu⁄• See <About Picture files> (page 6) for readable image specifications.• The [Memory] button on the “Background” screen becomes active only in STANDBY source mode.• Pressing the [Memory] button on the “Background” screen switches the AV OUT source to OFF. For resetting the AV OUT source, refer to <AV Output Interface Setup> (page 91). Panel Color Coordinate Panel Color CoordinateDNX9/ DDX8 series : Sets the button illumination color. DNX7 series : Sets the screen and button illumination color. 1 Display the Color screenTouch [ ] > > [ ] > > [Display] > > [Color]. (page 78)2 Display the Panel Color Coordinate screen[Initialize] Initialization resets the settings made using the Panel Color to the default settings made at the factory.[Panel Color Scan] When set to "ON", the illumination color of the screen and buttons changes one after another. (DNX9/ DDX8 series only)⁄• When touching [SET] or [Initialize], make sure [Panel Color Scan] is set to "OFF".3 Select a color1111 Sets to the touched color. [Adjust] Sets and registers favorite color to the preset buttons ([P1] – [P3]).
88 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 89Next page 3Next page 3screen.⁄• You can also register from the Bluetooth unit side. For the PIN code necessary for registration, see <Registering Bluetooth Unit PIN Code> (page 89). • If pairing cannot be done even when the PIN code is correct, try <Registering Special Bluetooth Unit>. Registering Special Bluetooth UnitRegisters Special Bluetooth unit that results in error by normal operation by selecting from model name. 1 Display the Special Device List screen2 Select a model nameDisplays the Bluetooth unit name that can be registered. 3 Confirm whether to register⁄• Only models in Bluetooth unit name list can be registered.4 Go through the procedure of <Registering Bluetooth Unit> and complete the registration (pairing). Registering Bluetooth Unit PIN Registering Bluetooth Unit PIN CodeCodeSets the PIN code of the Bluetooth unit to enter when registering (pairing) from the cell-phone or audio player side. 1 Display the Bluetooth Setup screenTouch [ ] > > [ ] > > [Bluetooth SETUP]. (page 78)2 Display the Receiver PIN Code screen3 Enter PIN code1111 Enters a code number.[Cancel] Cancels registration of PIN code. [Enter] Enters PIN code. [Clear] Clears the code number.Setup Menu Registering Bluetooth Unit Registering Bluetooth UnitRegisters the Bluetooth unit to be connected. 1 Display the Bluetooth Setup screenTouch [ ] > > [ ] > > [Bluetooth SETUP]. (page 78)2 Display the Connect Device List screen3 Search for a Bluetooth unit1111 Displays the registered Bluetooth units. [] When appears, the text display is scrolled by touching it.[Search] Searches for a Bluetooth unit.[SP DEV] Registers a Bluetooth unit that cannot be registered by normal register (paring) operation. ⁄• A new device cannot be registered if there are 5 registered Bluetooth units. Delete unnecessary registration. See <Bluetooth Unit Connection> (page 90). 4 Display the PIN Code Set screen1111 Display the PIN Code. [Search] Searches for a Bluetooth unit.[Cancel] Cancels searching of Bluetooth unit.[PIN Code Set] Display the PIN Code Set screen.5 Enter PIN code 1111 Enters a code number.[Enter] Enter the PIN code specified for the Bluetooth unit to register.This button will not be active until at least four PIN code digits have been entered. [Cancel] Cancels registration of PIN code. [Clear] Clears the code number.6 Select the Bluetooth unit to register1111 Displays the searched Bluetooth unit. Returns to the Connect Device List
90 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 91Next page 3Next page 3 AV Input Setup AV Input SetupYou can set AV input parameters. 1 Display the AV-IN Setup screenTouch [ ] > > [ ] > > [AV-IN SETUP]. (page 78)2 Set each item[AV-IN Interruption] Sets an image display of the system that is connected via the AV INPUT port. ( "OFF")"OFF": When the image source is switched, an image entered via the AV INPUT port is displayed."ON": When an image signal is entered via the AV INPUT port, this image is displayed.[iPod AV Interface Use] Sets the terminal which iPod is connected. ( "iPod")[AV-IN1 Name], [AV-IN2 Name], [AV-IN3 Name] Sets a name to be displayed when you select a system that is connected via the AV INPUT port. ( "VIDEO")⁄• [iPod AV Interface Use]This item can be set when in STANDBY source and also the iPod is disconnected.• [AV-IN Name]Two AV-IN names are displayed when "iPod" is selected in [iPod AV Interface Use] and three are displayed when not selected.• [AV-IN3 Name]DNX9/ DDX8 series only AV Output Interface Setup AV Output Interface SetupYou can set AV output parameters. 1 Display the AV-OUT Interface screenTouch [ ] > > [ ] > > [AV-OUT Interface]. (page 78)2 Set each item[AV-OUT] Selects an AV source to be output at the AV OUTPUT port. ( "OFF")Setup Menu Bluetooth Unit Connection Bluetooth Unit ConnectionSelects the Bluetooth unit to connect. 1 Display the Bluetooth Setup screenTouch [ ] > > [ ] > > [Bluetooth SETUP]. (page 78)2 Display the Connect Device List screen3 Select a registered Bluetooth unit4 Select the service to use[TEL (HFP)] Connects/disconnects cell-phone to use for Hands Free. [Audio (A2DP)] Connects/disconnects Audio player to use for Bluetooth Audio. [Remove] Deletes registration (pairing).Touching the screen displays a confirmation message. Touch [Yes]. To cancel clearing, touch [No]. Bluetooth Hands-Free/Audio Bluetooth Hands-Free/Audio Output SetupOutput SetupSelects speakers to output the sound of hands-free phoning (such as phone call voice and ringing tone) and Bluetooth audio. 1 Display the Bluetooth Setup screenTouch [ ] > > [ ] > > [Bluetooth SETUP]. (page 78)[Bluetooth HF/Audio] Sets the output speakers. ( "Front Only")"Front Only": Outputs from the front speakers. "All": Outputs from all the speakers.
92 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 93Next page 3Next page 3 Navigation Setup Navigation SetupYou can set Navigation parameters. 1 Display the Navigation Setup screenTouch [ ] > > [ ] > > [Navigation]. (page 78)2 Set each item[NAV Interrupt Speaker] Selects speakers used for voice guidance of the navigation system. ( "Front All")"Front L": Uses the front left side speaker for voice guidance."Front R": Uses the front right side speaker for voice guidance."Front All": Uses both front speakers for voice guidance.[NAV Voice Volume] Adjusts the volume for voice guidance of the navigation system. ( DNX series: "25", DDX series: "21")[NAV Mute] Mutes the volume of rear speakers during voice guidance of the navigation system. ( "ON")When turned "ON", the volume level drops for voice guidance.[Navigation Input] Selects a navigation system connection. ( "RGB") (DDX series only)"RGB": Allows the Kenwood’s Navigation System to connect via its interface cable."AV-IN": Allows a third-party navigation system to connect via the AV INPUT1 port."OFF": Must be used if no navigation system is connected. (The navigation display is cancelled when the AV source is switched.)[On Screen Navigation] Sets an on-screen display of the navigation screen. ( "OFF") (DDX series only)"Auto": Information is displayed for 5 seconds when updated. (Example : when the track/file/song has changed to the next one.)"OFF": Information is not displayed.⁄• [On Screen Navigation]It can be set only when [Navigation Input] is set to "AVIN". DSP Bypass Control (DNX7 series) DSP Bypass Control (DNX7 series)Temporarily bypassing DSP (Digital Signal Processor) System.1 Display the Audio SETUP screenTouch [ ] > > [ ] > > [Audio SETUP]. (page 78)2 Set the DSP Select[Bypass] There is no effect by DSP. [Through] There is an effect by DSP. ⁄• When the mode is set to [Bypass], DSP System cannot be adjusted. Setup Menu Camera Setup Camera SetupYou can set Camera parameters. 1 Display the AV Interface screenTouch [ ] > > [ ] > > [Camera SETUP]. (page 78)2 Set each item[Rear Camera] Selects the type of rear camera to use. ( "Other")"CMOS-300": When the CMOS-300 with ID 1 set is connected."Other": When the other camera is connected.[R-CAM Interruption] Sets a method to switch to the rear view camera video display. ( "OFF")"ON": Switches to the rear view camera video display when engaging the shift knob of car to "Reverse"."OFF": Switches to the rear view camera video display when engaging the shift knob of car to "Reverse" and then pressing the [AUD] button for longer than 1 second.The function of the [AUD] button needs to be set to "CAM" in [AUD Key Longer than 1 Second] beforehand. [R-CAM Settings] Adjusts the CMOS-300 with ID 1 set. For details, see the option manual.[F-CAM on AV-IN1] Turn this setting on when the CMOS-300 with ID2 set is connected. ( "OFF")[F-CAM Settings] Adjusts the CMOS-300 with ID 2 set. For details, see the option manual.
94 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 95Next page 3Next page 32 Display the Crossover setup screen3 Set the crossover[Phase] Sets the phase of subwoofer output. The phase is reversed 180 degrees when set to "Reverse". (Only when "Subwoofer" is set to any item other than "None" in Speaker Setup)[HPF FREQ] High Pass Filter adjustment. (When front, center or rear speaker is selected on Speaker Select screen)[LPF FREQ] Low Pass Filter adjustment. (When Subwoofer is selected on Speaker Select screen)[Slope] Sets a crossover slope. Car Type (DTA) Setup Car Type (DTA) SetupYou can setup the car type and speaker network, etc.1 Display the Car Type Setup screenTouch [ ] > > [ ] > > [Audio SETUP] > > [Car Type]. (page 78)2 Setup the Car TypeIf your car type is selected, the Digital Time Alignment and Equalizer is set automatically (for timing adjustment of sound output for each channel) to have the highest surround effects.1111 Sets up the car type you use together with this unit.You can choose according to type of your car."OFF", "Compact", "Full Size Car", "Wagon", "Minivan", "SUV", "Minivan (Long)"[Location] Sets the locations of the speakers.[Adjust] Displays the Car Type Adjust screen. You can adjust the digital time alignment that was set automatically when you selected the car type.Setup Menu Speaker Setup Speaker SetupYou can select a speaker type and its size to get the best sound effects.1 Display the Speaker Select screenTouch [ ] > > [ ] > > [Audio SETUP] > > [Speaker Select]. (page 78)2 Select a speaker you wish to adjustWhen the speaker type and size are set, the speaker crossover network and equalizer curve are set automatically.2221113334441 Center speaker (DNX9/ DDX8 series)2 Front speaker3 Rear speaker4 Subwoofer[Tweeter] You can set the tweeter when you are selecting front speakers. If you are using a tweeter together with the front speakers, set the tweeter to "ON". In the "ON" position, the Equalizer is adjusted to its best position.[X'over] Displays the Speaker Crossover Setup screen.You can adjust the crossover setup that was set automatically when you selected the speaker type.3 Select a speaker typeYou can select any of the following speaker types."Center" None, 2-3/4x1-9/16 inch, 2 inch, 4 inch, 5 inch, 6-1/2 inch over"Front" OEM, 4 inch, 5 inch, 6-1/2 inch, 6-3/4 inch, 7 inch, 4x6, 5x7, 6x8, 6x9, 7x10"Rear" None, OEM, 4 inch, 5 inch, 6-1/2 inch, 6-3/4 inch, 7 inch, 4x6, 5x7, 6x8, 6x9, 7x10"Subwoofer" None, 6 1/2 inch, 8 inch, 10 inch, 12 inch, 15 inch over⁄• Select "None" if you have no speakers.• If you set the center speaker to "None" even in a short time when you are setting the Surround Control to "Bypass+Center", the Surround Control is set to "Bypass" automatically. See <Surround Control> (page 77).• If you set the center and rear speakers to "None" when you are setting the Surround Control to "Dolby PL II", the Surround Control is set to "Bypass" automatically. See <Surround Control> (page 77). Crossover Network SetupYou can set a crossover frequency of speakers.1 Select the speaker to set the crossover2221113334441 Sets the High Pass Filter of the center speaker. (DNX9/ DDX8 series)2 Sets the High Pass Filter of the front speaker.3 Sets the High Pass Filter of the rear speaker.4 Sets the Low Pass Filter of the subwoofer.
96 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 97Next page 3Next page 3sitting in the front seat, and set the right and left positions to the center of the vehicle interior.2 Measure the distances from the reference point to the speakers.3 Calculate the distance difference in accordance with the farthest speaker.1.6feet2.5feet5feet +2.5feet+0feet+3.4feet Channel Level (DNX9/ DDX8 series) Channel Level (DNX9/ DDX8 series)You can set the volume at each setup position.1 Display the Car Type Setup screenTouch [ ] > > [ ] > > [Audio SETUP] > > [Channel Level]. (page 78)2 Select a speaker you wish to adjust2221114443335556661 Center speaker2 Left front speaker3 Right front speaker4 Left rear speaker5 Right rear speaker6 Subwoofer[Test Tone] Starts or stops test signal tone output for setup check.3 Adjust the volumeSetup MenuSpeaker Location setup1 Display the Speaker Location Setup screen2 Set the speaker locations[Front Speaker] Sets the location of the front speaker."Door", "On Dash", "Under Dash"[Rear Speaker] Sets the location of the rear speaker."Door", "Rear Deck""2nd Row", "3rd Row" (Minivan, Minivan (Long))Car Type Adjust You can manually set the sound output timing of each channel.1 Display the Car Type Adjust screen2 Select a speaker you wish to adjust2221113334441 Center speaker (DNX9/ DDX8 series)2 Front speaker3 Rear speaker4 Subwoofer3 Set a delay timeMake fine adjustment of the delay time of the speaker output specified at <Setup the Car Type> to have a more suitable environment for your vehicle.The settings of the delay time are automatically identified and compensated by specifying the distances of each speaker from the center of the vehicle interior.1 Set the front and rear positions and the height of the reference point to the position of the ears of the person
98 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 99Next page 3Next page 3 DVD Language Setup DVD Language SetupSelects a language you use for the speech and menus.1 Display the DVD Setup screenTouch [ ] > > [ ] > > [DVD SETUP]. (page 78)2 Select the language item to set3 Enter a language codeSee <DVD Language Codes> (page 115) and select the desired language.1111 Enters a language code.[Cancel] Cancels the language setup and returns to the "DVD SETUP" screen.[Enter] Sets the language and returns to the "DVD SETUP" screen. (It appears after you have entered a language code.)[Original] Sets the DVD's original language (only when setting an audio language).[Clear] Clears the language code.4 Set the language you use DVD Parental Level Setup DVD Parental Level SetupSets a parental level.1 Display the DVD Setup screenTouch [ ] > > [ ] > > [DVD SETUP]. (page 78)2 Display the Parental Level code number screen3 Enter the code number1111 Enters a code number.[Cancel] Cancels the current setup and returns to the "DVD SETUP" screen.[Level] Indicates the present parental lock level.[Enter] Determines the code number and displays the Parental Level setup screen.Setup Menu DVD Setup DVD SetupYou can set up the DVD play.1 Display the DVD Setup screenTouch [ ] > > [ ] > > [DVD SETUP]. (page 78)2 Set each item[Menu Language]*1 Selects a disc menu language. See <DVD Language Setup> (page 99).[Subtitle Language]*1 Selects a subtitle language. See <DVD Language Setup> (page 99).[Audio Language]*1 Selects an audio language. See <DVD Language Setup> (page 99).[Dynamic Range Control]*1 Sets the dynamic range. ( "Dialog")The dynamic range is reduced by changing from "Wide" to "Normal" and from "Normal" to "Dialog". "Dialog" makes the total sound volume becomes larger as compared with "Wide" and "Normal", allowing you to listen to the movie's dialog more clearly. This is effective only when you are using a Dolby Digital software.The operation is available during the play stop mode.[Angle Mark] Sets an angle mark display. ( "ON")[Screen Ratio]*1 Selects the screen display mode. ( "16:9")"16:9": Displays wide pictures."4:3 LB": Displays wide pictures in the Letter Box format (having black stripes at the top and bottom of screen)."4:3 PS": Displays wide pictures in the Pan & Scan format (showing pictures cut at the right and left ends).[Parental Level]*1 Displays the Parental Lock screen. ( "OFF")See <DVD Parental Level Setup> (page 99).[Disc SETUP] Makes the settings related to the disc media. See <Disc Setup> (page 100).[Stream Information] Displays the present source information.The stream (Dolby Digital, dts, Linear PCM, MPEG, MP3, WMA or AAC) is displayed. (DNX7 series only)⁄• * Disabled when a DVD is being played.
100 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 101Next page 3Next page 3⁄• [CD Read]Disabled when a disc is in the unit.You cannot play an Audio file/VCD disc in the "2" position. Also, you may not play some music CDs in the "2" position. USB Setup USB SetupPerforms setup when using USB.1 Display the USB Setup screenTouch [ ] > > [ ] > > [USB SETUP]. (page 78)2 Set each itemExample : USB Setup screen[Picture Display Time] Selects a picture display time. ( "Long")The Display of a JPEG picture is changed. ("Short", "Middle", "Long")[On Screen USB] Sets an on-screen display of the USB Playback screen. ( "Auto")"Auto": Information is displayed for 5 seconds when updated."OFF": Information is displayed when you touch on the screen. iPod Setup iPod SetupPerforms setup when using iPod.1 Display the iPod Setup screenTouch [ ] > > [ ] > > [iPod SETUP]. (page 78)2 Set each item[AudioBook Speed] Sets the Audio book playback speed. ( "Normal")[Wide Screen] Sets Wide Screen on or off. ( "OFF")[On Screen iPod] Sets an on-screen display of the iPod Playback screen. ( "Auto")"Auto": Information is displayed for 5 seconds when updated."OFF": Information is displayed when you touch on the screen.⁄• "Wide Screen" cannot be set while the iPod is connected.Setup Menu[Clear] Clears the code number.⁄• The number you enter first is set as your code number.4 Display the Parental Level SETUP screen5 Select a parental level and complete the setupSelects a parental level.⁄• If a disc has higher parental lock level, you need to enter the code number.• The parental lock level varies depending on a loaded disc.• If a disc has no parental lock, anybody can play it back even when you have set the parental lock. Disc Setup Disc SetupPerforms setup when using disc media.1 Display the DVD Setup screenTouch [ ] > > [ ] > > [DVD SETUP]. (page 78)2 Display the Disc Setup screen3 Set each item[CD Read] Sets a music CD playback. ( "1")"1": Automatically recognizes and plays back an Audio file disc, a DVD or a music CD."2": Forcibly plays back a disc as a music CD. Select "2" if you wish to play a music CD having a special format or if you cannot play a disc in the "1" position.[On Screen DVD] Sets an on-screen display of the DVD Playback screen. ( "OFF")"Auto": Information is displayed for 5 seconds when updated."OFF": Information is not displayed.
102 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 103Next page 3Next page 3Parental Lock SetupParental Lock SetupSelects the channel to enable SIRIUS Parental lock function. 1 Display the SIRIUS Setup screenTouch [ ] > > [ ] > > [SIRIUS SETUP]. (page 78)2 Display the Parental Code screenڥ You need to complete <SIRIUS Parental Code Setup> beforehand.3 Enter the code numberEnter the same code number as you originally input <SIRIUS Parental Code Setup> (page 102).4 Display the Parental Code screen5 Enter the code number6 Select a category1111 Category list Displays all the channels in the selected category.[All Channel] Displays all the channels.7 Set the parental lock for each channel3331112221 Channel list2 Sets the Parental lock function on or off for each channel.3 Selects a channel[Info Change] Switch the sequence of the channel list. (Channel name, Song title, Artist name, Composer name, and Category name)[UP] Moves to SIRIUS Category Select screen.Setup Menu SIRIUS Parental Code Setup SIRIUS Parental Code SetupSets a SIRIUS Parental code. (with the optional accessory SIRIUS Tuner connected only)1 Display the SIRIUS Setup screenTouch [ ] > > [ ] > > [SIRIUS SETUP]. (page 78)2 Display the Parental Code screenڥ If you have already completed the code registration, [Change] is displayed.3 Enter the Parental Code number1 Enters a code number.[Cancel] Cancels the current setup and returns to the SIRIUS Setup screen.[Enter] Determines the code number.[Clear] Clears the code number.4 Confirm the code numberEnter the same code number as you input in step 3.SIRIUS Parental code is now set, and the display returns to SIRIUS Setup screen.Change the Parental Code1 Display the Parental Code screen[Clear] Clears the Parental Code.ڥ Pressing [Clear] for 5 seconds or longer deletes the code.2 Enter the current code number1113 Enter the new code number4 Confirm the code numberEnter the same code number as you input in step 3.SIRIUS Parental code is now set, and the display returns to SIRIUS Setup screen.
104 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 105Next page 3Remote ControllerThis unit can be operated using the Remote Controller supplied with this unit.Battery installationBattery installationUse two "AAA"/"R03"-size batteries.Insert the batteries with the + and – poles aligned properly, following the illustration inside the case.⁄• If the Remote Controller operates only over shorter distances or does not operate at all, it is possible that the batteries are depleted. In such instances, replace the both batteries with new ones. Remote Controller mode switch Remote Controller mode switchThe functions operated from the remote controller differ depending on the position of the mode switch.DVDTVNAVAUDUUUUAUD modeSwitch to this mode when controlling a selected source or tuner source, etc.DVD modeSwitch to this mode when playing DVDs or CDs etc. with the player integrated in this unit.¤ CAUTION• Put the Remote Controller in a place where it will not move during braking or other operations. A dangerous situation could result, if the Remote Controller falls down and gets wedged under the pedals while driving.• Do not leave the battery near fire or under direct sunlight. A fire, explosion or excessive heat generation may result.• Do not recharge, short, break up or heat the battery or place it in an open fire. Such actions may cause the battery to leak fluid. If spilled fluid comes in contact with your eyes or on clothing, immediately rinse with water and consult a physician.• Place the battery out of reach of children. In the unlikely event that a child swallows the battery, immediately consult a physician.Setup MenuSIRIUS Skip Channel SelectSIRIUS Skip Channel SelectSets the undesired channels unselected. 1 Display the SIRIUS Setup screenTouch [ ] > > [ ] > > [SIRIUS SETUP]. (page 78)2 Display the Skip Category Select screen3 Select a category1111 Category list Displays all the channels in the selected category.[All Channel] Displays all the channels.4 Set the skip for each channel3331112221 Channel list2 Sets the skip function on or off for each channel.3 Selects a channel[Info Change] Switch the sequence of the channel list. (Channel name, Song title, Artist name, Composer name, and Category name)[UP] Moves to SIRIUS Category Select screen. TV Setup TV SetupThe TV signal receiving areas can be set. (with the optional accessory TV Tuner connected only)1 Display the TV SETUP screenTouch [ ] > > [ ] > > [TV SETUP]. (page 78)2 Set each item[On Screen TV] Sets an on-screen display of the TV screen.( "Auto") (with the optional accessory TV tuner connected only)"Auto": Information is displayed for 5 seconds when updated."OFF": Information is displayed when you touch on the screen.
106 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 107Next page 3Next page 3Hands-free communicationWhen a call comes in, it answers the call.FunctionSwitches the function screenMODESwitches the screen mode.Screen mode changes each time you press this key.DVD/VCD (DVD mode)DVD/VCD (DVD mode)Track search and file searchSelects the track or file to be played.Play/PausePauses the track.Press again to resume playing.StopMemorizes the last point where the disc stopped. When pressed again, the last point is deleted.Direct searchPressing this key switches the features that can be searched directly.DVD-VIDEOTitle numberChapter numberPlay timeItem number*Cancel* You may not be able to use this function with some discs or scenes.Remote ControllerDual ZoneSwitches the Dual Zone function ON and OFF.Rear volume controlAdjusts volume at rear when the Dual Zone function is ON.V.SELSwitches to the navigation screen.Display angleSwitches the display angle each time it is pressed.Cursor keyMoves the cursor when displaying menu.ENTEREnters options.TV modeThis is switched when controlling TV.NAVI modeThis is switched when controlling Navigation unit.⁄• The position of the remote control mode switch is indicated in the title of each mode, e.g., "(AUD mode)".• When controlling a player that is not integrated in the unit, select "AUD" mode.Common operations (AUD mode)Common operations (AUD mode)Source switchingSwitches to the source to be played.Volume controlAdjusts the volume.Volume attenuatorPress the key once to lower the volume. Press again to restore the previous volume.
108 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 109Next page 3Next page 3Remote ControllerSUBTITLESwitches the subtitle language.ZOOMSwitches the zoom ratio each time you press this key.Picture AngleSwitches the picture angle each time you press this key.AUDIOSwitches the voice language each time you press this key.VCD 1.X, VCD 2.X (PBC OFF)Track numberCancelVCD 2.X (PBC ON)Scene numberNumberCancelOnce you have switched to the direct search feature, specify the search number from the numeric keypad, and then press [ENTER] key.Numeric keypad• Specify the number to search in direct search.• Press 1 2ABC to fast forward/backward. Switches the fast forward/backward speed each time you press this key.• Press 4GHI 5JKL to slow forward/backward. Switches the slow playback speed each time you press this key.DVD Top MenuReturns to the DVD top menu.DVD MenuDisplays the DVD menu.Turns the playback control on or off while playing VCD.Music CD/Audio file/Video file/ Music CD/Audio file/Video file/ Picture file (AUD mode)Picture file (AUD mode)Folder search Selects the folder to be played.Track search and file searchSelects the track or file to be played.Play/PausePauses the track or file.Press again to resume playing.Direct searchPressing this key switches the features that can be searched directly.Music CDTrack numberPlay timeCancelAudio files in DVD/CD discFolder numberFile numberCancelOnce you have switched to the direct search feature, specify the search number from the numeric keypad, and then press [38] key.Numeric keypad• Specify the number to search in direct search.iPod (AUD mode)iPod (AUD mode)Music/Video searchSelects the music/video to be played.Play/PausePauses the music/video.Press again to resume playing.
110 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 111Next page 3Next page 3ROUTE MDisplays Route Option menu.VIEWSwitches between 2D and 3D map displays.VOICEPlays Voice guidance.MAP DIRSwitches between the heading up navigation and north up navigation map displays.Remote ControllerRadio (AUD mode)Radio (AUD mode)FM band switchingSwitches to bands received by the unit.AM bandStation selectionSwitches to broadcast stations received by the unit.Seek mode switchingSwitches the Seek mode (AUTO1, AUTO2, MANU).Direct tuningAfter pressing this key, use the keypad to specify the broadcast station you wish to receive.Example: 92.1MHz (FM)9WXYZ 2ABC 1« or Example: 810kHz (AM)8TUV 1 0« or Numeric keypad• To use preset tuning, press the number of a programmed broadcast station. (1 – 6MNO )• Press the direct tuning key first, then specify the frequency of the station to receive.NAVI (NAVI mode)NAVI (NAVI mode)Cursor keyScrolls the map, or moves the cursor.ENTERPerforms the selected function.ZOOMZooms in or out the navigation map.MENUDisplays Main menu.CANCELDisplays previous screen.POSITIONDisplays the current position.
112 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 113Remote ControllerTV (TV mode)TV (TV mode)Switching Band/VideoIt switches between the station of the TV band to receive and video input.Channel SelectionThe TV channel to receive is selected.Direct tuning(NTSC TV type only)Press this key first, and then specify the station to receive with the numeric keypad.Example: In case of Channel 6 (2-digit)0 6MNO« or Numeric keypad• The number of the memorized station is selected. (1 – 6MNO )• Press the direct tuning key first, then specify the channel of the station to receive.3 End initial setup⁄• The settings above can be changed in <Setup Menu> (page 78). Initial Setup Initial Setup1 Turns the power On2 Set each item[Language] Select the language used for the control screen and setting items. (page 80)[Angle] You can adjust the position of the monitor. (page 82)[iPod AV Interface Use] Sets the terminal which the iPod is connected to. ( "iPod")[Color] Sets the screen and button illumination color. (page 86)[EXT SW] Setting up external switch power mode. (page 83) [Camera] You can set Camera parameters. See <Camera Setup> (page 92). When pressing the Reset button or turning on the unit for the first time, the Initial SETUP screen is displayed. Initial Setup
114 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 115SourceDisplay OverviewiPod"MUSIC" Identifies the music file."VIDEO" Identifies the video file."RDM" Indicates that the Random function is ON."A-RDM" Indicates that the Album random function is ON."REP" Indicates that the Repeat function is ON.Tuner"AF" Indicates that the AF search function is ON."AUTO1" Indicates that Seek mode is set to Auto1."AUTO2" Indicates that Seek mode is set to Auto2."CRSC" Indicates that the CRSC function is OFF. "MANU" Indicates that Seek mode is set to Manual."RDS" Indicates the state of the RDS station when the AF function is ON. (White: RDS is being received. Orange: RDS is not being received.)"ST" Indicates that stereo broadcast is being received."TI" Indicates the reception state of traffic information. (Orange: TP is being received. White: TP is not being received.)HD Radio"AUTO1" Indicates that Seek mode is set to Auto1."AUTO2" Indicates that Seek mode is set to Auto2."MANU" Indicates that Seek mode is set to Manual."HD" Indicates that HD Radio station is being received."M/S" Indicates whether the reception channel is main or sub. (Orange: Sub channel White: Main channel)"ANALOG" Indicates that analog broadcast is being received."DIGITAL" Indicates that digital broadcast is being received."ST" Indicates that stereo broadcast is being received. "TAG" Indicates that Tagging is enabled.SIRIUS/ XM"SCN" Indicates that the channel scan function is ON. "SEEK1" Indicates that Seek mode is set to 1."SEEK2" Indicates that Seek mode is set to 2.TV"AUTO1" Indicates that Seek mode is set to Auto1."AUTO2" Indicates that Seek mode is set to Auto2."MANU" Indicates that Seek mode is set to Manual.Shown below is a list of indicators displayed on the Status bar. SourceDisplay OverviewGeneral"ATT" Indicates that the attenuator is active."DUAL" Turns on the Dual zone function."LOUD" Indicates that the Loudness control function is ON. "TEL" Indicates the connection state of the Bluetooth hands-free unit. (White: Connected. Orange: Not connected.)DVD/CD"FO-REP" Indicates that the Folder repeat function is ON."IN" Indicates that a disc is inserted. (White: A Disc is inside the unit. Orange: Error at the disc player.)"MOVIE" Identifies the video file."MUSIC" Identifies the music file."RDM" Indicates that the Random function is ON."REP" Indicates that the Repeat function is ON.DVD-Video"C-REP" Indicates that the Chapter repeat function is ON."T-REP" Indicates that the Title repeat function is ON.VCD"1chLL" Identifies the left audio output of channel 1. "1chLR" Identifies the monaural audio output of channel 1. "1chRR" Identifies the right audio output of channel 1. "1chST" Identifies the stereo audio output of channel 1. "LL" Identifies the left audio output."LR" Identifies the monaural audio output."RR" Identifies the right audio output."ST" Identifies the stereo audio output."PBC" Indicates that the PBC function is ON. "SVCD" Identifies the Super Video CD."VER1" Indicates that the Video CD version is 1."VER2" Indicates that the Video CD version is 2."REP" Indicates that the Repeat function is ON.USB"FO-REP" Indicates that the Folder repeat function is ON."MOVIE" Identifies the video file."MUSIC" Identifies the music file."PICTURE" Identifies the image file."RDM" Indicates that the Random function is ON."REP" Identifies that the Repeat function is ON."PLST" Indicates that the Play list mode is selected now.Status bar Indicator items DVD Language CodesCode Languageaa Afarab Abkhazianaf Afrikaansam Amharicar Arabicas Assameseay Aymaraaz Azerbaijaniba Bashkirbe Byelorussianbg Bulgarianbh Biharibi Bislamabn Bengali, Banglabo Tibetanbr Bretonca Catalanco Corsicancs Czechcy Welshda Danishde Germandz Bhutaniel Greeken Englisheo Esperantoes Spanishet Estonianeu Basquefa Persianfi Finnishfj Fijifo Faroesefr Frenchfy Frisianga Irishgd Scots Gaelicgli Galiciangn Guaranigu Gujaratiha Hausahe Hebrewhi Hindihr Croatianhu Hungarianhy Armeniania InterlinguaCode Languageie Interlingueik Inupiakid Indonesianis Icelandicit Italianja Japanesejv Javaneseka Georgiankk Kazakhkl Greenlandickm Cambodiankn Kannadako Koreanks Kashmiriku Kurdishky Kirghizla Latinlb Luxembourgishln Lingalalo Laotianlt Lithuanianlv Latvian, Lettishmg Malagasymi Maorimk Macedonianml Malayalammn Mongolianmo Moldavianmr Marathims Malaymt Maltesemy Burmesena Naurune Nepalinl Dutchno Norwegianoc Occitanom (Afan) Oromoor Oriyapa Punjabipl Polishps Pashto, Pushtopt Portuguesequ Quechuarm Rhaeto-Romancern Kirundiro RomanianCode Languageru Russianrw Kinyarwandasa Sanskritsd Sindhisg Sanghosh Serbo-Croatiansi Singhalesesk Slovaksl Sloveniansm Samoansn Shonaso Somalisq Albaniansr Serbianss Siswatist Sesothosu Sundanesesv Swedishsw Swahilita Tamilte Telugutg Tajikth Thaiti Tigrinyatk Turkmentl Tagalogtn Setswanato Tongantr Turkishts Tsongatt Tatartw Twiuk Ukrainianur Urduuz Uzbekvi Vietnamesevo Volapukwo Wolofxh Xhosayo Yorubazh Chinesezu Zulu
116 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 117Next page 3Next page 3Help? TroubleshootingSome functions of this unit may be disabled by some settings made on this unit. ! • Cannot set up the subwoofer. • Cannot set up subwoofer phase. • No output from the subwoofer. • Cannot set up the low pass filter. • Cannot set up the high pass filter.▲ Subwoofer is not set to On. ☞ <Speaker Setup> (page 94)▲ The Dual zone function is enabled. ☞ <Zone Control> (page 74) ! • Cannot select the output destination of the subsource in the Dual zone. • Cannot adjust the volume of the rear speakers.▲ The Dual zone function is disabled. ☞ <Zone Control> (page 74) ! Cannot play audio files.▲ "CD Read" of <Disc Setup> (page 100) is set to "2". ! Cannot Folder select.▲ The Random play function is enabled. ! Cannot perform Repeat play.▲ The PBC function of the Video CD is enabled. ! • Cannot set up the equalizer. • Cannot set up the crossover network.▲ The Dual zone function is enabled. ☞ <Zone Control> (page 74) ▲ The DSP Select is Bypass. ☞ <DSP Bypass Control> (page 93) What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems.General ? The Touch Sensor Tone doesn’t sound.✔ The preout jack is being used.☞ The Touch Sensor Tone can’t be output from the preout jack.Tuner source ? Radio reception is poor.✔ The car antenna is not extended.☞ Pull the antenna out all the way.✔ The antenna control wire is not connected.☞ Connect the wire correctly, referring to the section on <INSTALLATION MANUAL>.Disc source ? The specified disc does not play, but another one plays instead.✔ The specified CD is quite dirty.☞ Clean the CD.✔ The disc is severely scratched.☞ Try another disc instead.Audio file source ? The sound skips when an Audio file is being played.✔ The media is scratched or dirty.☞ Clean the media, referring to the CD cleaning of the section on <Handling discs> (page 4).✔ The recording condition is bad.☞ Record the media again or use another media.Help? ErrorWhen the unit fails to operate correctly, the cause of the failure appears on the display."Protect" :Protective circuit has been activated because a speaker cord has shorted or it has come in contact with the car chassis.➡ Wire or insulate the speaker cord as appropriate and then push the Reset button."Hot Error" : When the internal temperature of this unit rises to 60°C or more, the protection circuit is activated and you may not be able to operate the unit. At such times this message will appear.➡ Use the unit again after reducing the temperature inside the vehicle."Hold Error" : Activation of the protective circuit when the temperature inside the disc changer is higher than 60 degrees Celsius stops the disc changer from operating. At such times this message will appear.➡ Use when the temperature at the site where the disc changer has been fitted has dropped."Mecha Error" : The disc player is malfunctioning.➡ Eject the disc and try inserting it again. Contact the Kenwood dealer if this indicator continues blinking or the disc cannot be ejected."Disc Error" : An unplayable disc is inserted."Read Error" :Disc is quite dirty.➡ Clean the disc, referring tot he section on <Handling discs> (page 4). Disc is upside down.➡ Load the disc with the labeled side up. "Region code Error" :The disc you wanted to play has a region code that cannot be played with this unit."Parental level Error" :The disc you wanted to play has a higher level than the parental level you set."Error 07–67" : The unit is not operating correctly due to some reason or other.➡ Push the unit's Reset button. If the "Error 07−67" message does not disappear, see your nearest Kenwood dealer."No Device" (USB device): The USB device is selected as a source although no USB device is connected.➡ Change the source to any source other than USB/iPod. Connect an USB device, and change the source to USB again."Disconnected" (iPod, Bluetooth audio player): The iPod/Bluetooth audio player is selected as a source although no iPod/Bluetooth audio player is connected.➡ Change the source to any source other than iPod/Bluetooth. Connect an iPod/Bluetooth audio player, and change the source to iPod/Bluetooth again."No Music" : The connected USB device contains no playable audio file.Media was played that doesn’t have data recorded that the unit can play."USB Device Error!!" : The connected USB device is rated a current capacity higher than the allowable limit. ➡ Check the USB device.Some trouble may have occurred to the connected USB device.➡ Change the source to any source other than USB. Remove the USB device.
118 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 119Next page 3"Authorization Error" : Connection to the iPod has failed.➡ Remove the iPod and then reconnect it.The unit does not support the iPod.➡ Refer to <iPod/iPhone that can be connected to this unit> (page 7)."Update your iPod" : The iPod's software is an older version which the unit can not support.➡ Confirm that the software for the iPod is the latest version. Refer to <iPod/iPhone that can be connected to this unit> (page 7)."You only can connect one iPod." : More than one iPod are connected to this unit.➡ Connect only one iPod to the USB terminal with iPod tag."Update your USB database" : The USB device is different from the previous one or the contained audio files are replaced.➡ Update your database. Refer to <Source Control Screen> (page 26) of USB Device Control."Navigation Error. Please turn on power again later." (DNX series only) : The communication error has occurred due to severely cold temperature.➡ Turn on power again after warming your car interior."No Navigation" (DDX series only): This unit does not support the connected navigation unit.➡ The latest information on the connectable navigation unit can be obtained from http://www.kenwood.com/cs/ce.No navigation unit is connected.➡ Connect a supported navigation unit."CHECK SIRIUS" : The unit cannot recognize the connected SIRIUS Tuner Box.➡ Check the connection of the SIRIUS Tuner Box."ANTENNA ERROR" : Something is wrong with the antenna.➡ Check the connection of the antenna."ACQUIRING SIGNAL" : The unit cannot receive any signal.➡ Move the vehicle to the area where the unit can receive signal."FIRMWARE UPDATING" : Updating the firmware of SIRIUS tuner. ➡ Operation is invalid until the update is completed."CHANNELS UPDATING **% COMPLETE" : Updating the SIRIUS Channel Map. ➡ Operation is invalid until the update is completed."SUBSCRIPTION UPDATED" : Updating the subscription information. ➡ Operation is invalid until the update is completed."INVALID CHANNEL" : The selected channel is invalid.➡ Select a different channel."CALL 888-539-SIRIUS TO SUBSCRIBE" : The selected channel is not subscribed.➡ Call the displayed number for subscription."Check XM Tuner" : The unit cannot recognize the connected XM Tuner.➡ Check the connection of the XM Tuner."No Signal" : The unit cannot receive any signal.➡ Check the connection of the antenna."Check Antenna" : Something is wrong with the antenna.➡ Check the connection of the antenna."Ch Unavailable" : The selected channel is invalid.➡ Select a different channel."Ch Unauthorized" : The selected channel is not subscribed."Channel Off Air" : The broadcast of the selected channel has finished.Help? Error SpecificationsMonitor sectionMonitor sectionPicture Size: 6.95 inches (diagonal) wide: 156.6 mm (W) x 81.6 mm (H)Display System: Transparent TN LCD panelDrive System: TFT active matrix systemNumber of Pixels: 1,152,000 (800H x 480V x RGB)Effective Pixels: 99.99 %Pixel Arrangement: RGB striped arrangementBack Lighting: LEDDVD player sectionDVD player sectionD/A Converter: 24 bitAudio Decoder: Linear PCM/ Dolby Digital/ dts/ MP3/ WMA/ AACVideo Decoder: MPEG1/ MPEG2: DivX (DNX9/ DDX8 series)Wow & Flutter: Below Measurable LimitFrequency ResponseDNX9/ DDX8 seriesSampling frequency; 96 kHz : 20 – 22,000 Hz48 kHz : 20 – 22,000 Hz44.1 kHz : 20 – 20,000 HzDNX7 seriesSampling frequency; 96 kHz : 20 – 20,000 Hz48 kHz : 20 – 20,000 Hz44.1 kHz : 20 – 20,000 HzTotal Harmonic Distortion: 0.008 % (1 kHz)S/N Ratio (dB): 98 dB (DVD-Video 96 kHz)Dynamic Range: 98 dB (DVD-Video 96 kHz)Disc Format: DVD-Video/ VIDEO-CD/ CD-DASampling Frequency: 44.1/ 48/ 96 kHzQuantifying Bit Number: 16/ 20/ 24 bitUSB interface sectionUSB interface sectionUSB Standard: USB 2.0 High speediPod: USB 1.1 Full speed (DNX9/ DDX8 series only)File System: FAT 16/ 32Maximum Power Supply Current: 500 mAD/A Converter: 24 BitVideo Decoder: MPEG1/ MPEG2/ MPEG4/ H.264/ WMVAudio Decoder: MP3/ WMA/ AAC/ WAV (Linear PCM)Bluetooth sectionBluetooth sectionTechnology: Bluetooth Ver.2.1 + EDR CertifiedFrequency: 2.402 – 2.480 GHzOutput Power: +4dBm (MAX), 0dBm (AVE), Power Class2Maximum Communication range: Line of sight approx. 10m (32.8 ft)ProfileHFP (Hands Free Profile), SPP (Serial Port Profile), HSP (Headset Profile), OPP (Object Push Profile), PBAP (Phonebook Access Profile), SYNC (Synchronization Profile), A2DP (Advanced Audio Distribution Profile), AVRCP (Audio/Video Remote Control Profile)
120 DNX series DNX9960/ DNX7160/ DNX7020EX DDX series DDX896/ DDX8046BT English 121Video sectionVideo sectionColor System of External Video Input: NTSCExternal Video Input Level (mini jack): 1 Vp-p/ 75 ΩExternal Audio Max Input Level (mini jack): 2 V/ 25 kΩVideo Output Level (RCA jacks): 1 Vp-p/ 75 ΩAudio Output Level (RCA jacks): 1.2 V/ 10 kΩAnalog RGB input (DDX series only): 0.7 Vp-p/ 75 ΩAudio sectionAudio sectionMaximum Power (Front & Rear): 50 W x 4Full Bandwidth Power (Front & Rear)(4 Ω, 14.4 V, 1 % THD): 22 W x 4Preout Level (V): 5 V/ 10 kΩ (DNX9/ DDX8 series): 2 V/ 10 kΩ (DNX7 series)Preout Impedance: 80 Ω (DNX9/ DDX8 series): ≤ 600 Ω (DNX7 series)Speaker Impedance : 4 – 8 ΩFM tuner sectionFM tuner sectionFrequency Range 200 kHz : 87.9 MHz – 107.9 MHz (DNX9960/ DNX7160/ DNX7020EX/ DDX896)50 kHz : 87.5 MHz – 108.0 MHz (DDX8046BT)Usable Sensitivity (S/N :30 dB): 9.3 dBf (0.8 μV/ 75 Ω)Quieting Sensitivity (S/N :50 dB): 15.2 dBf (1.6 μV/ 75 Ω)Frequency Response (± 3.0 dB): 30 Hz – 15 kHzS/N Ratio (dB): 70 dB (MONO)Selectivity (± 400 kHz): ≥ 80 dB Stereo Separation: 35 dB (1 kHz)AM tuner sectionAM tuner sectionFrequency Range (10 kHz): 530 kHz – 1700 kHzUsable Sensitivity: 28 dBμSpecificationsDSP SectionDSP SectionGraphics equalizerDNX9/ DDX8 seriesBand: 13 BandFrequency (BAND1 – 13): 62.5/ 100/ 160/ 250/ 400/ 630/ 1k/ 1.6k/ 2.5k/ 4k/ 6.3k/ 10k/ 16k HzChannel: Front/ Rear/ CenterDNX7/ DDX7 seriesBand: 5 BandFrequency (BAND1 – 5): 62.5/ 250/ 1k/ 4k/ 16k HzGain: -9/ -8/ -7/ -6/ -5/ -4/ -3/ -2/ -1/ 0/ 1/ 2/ 3/ 4/ 5/ 6/ 7/ 8/ 9 dBX'overHigh pass filterFrequency: Through, 30/ 40/ 50/ 60/ 70/ 80/ 90/ 100/ 120/ 150/ 180/ 220/ 250 HzSlope: -6/ -12/ -18/ -24 dBLow pass filterFrequency: 30/ 40/ 50/ 60/ 70/ 80/ 90/ 100/ 120/ 150/ 180/ 220/ 250 Hz, ThroughSlope: -6/ -12/ -18/ -24 dBTime alignmentFront/ Rear/ Subwoofer: 0 – 20.01 ft (0.07 ft Step)Center: 0 – 11.15 ft (0.07 ft Step) (DNX9/ DDX8 series)Position: 0 – 5.68 ft (0.07 ft Step)Channel Level (DNX9/ DDX8 series): ± 10 dBNavigation section (DNX series Navigation section (DNX series only)only)Receiver: High-sensitivity GPS receiverReception Frequency: 1575.42 MHz (C/A code)Acquisition TimesCold : < 38 secondsFactory Reset : < 45 seconds(On average for a stationary receiver with a clear view of the sky)AccuracyPosition : < 10 meters typicalVelocity : 0.05 m/sec. RMSPosition Method: GPS Antenna: External GPS antenna External SW External SWMaximum Power Supply Current: 500 mAGeneralGeneralOperating voltage: 14.4 V (10.5 – 16 V allowable) Maximum Current Consumption: 15 A Dimensions (W × H × D): 181.7 × 100.0 × 180 mm7-3/16 x 3-15/16 x 7-1/8 inchOperational Temperature Range: -10 °C – +60 °CStorage Temperature Range: -20 °C – +85 °CWeight DNX9 series : 2.54 kg (5.6 lbs)DNX7 series : 2.50 kg (5.5 lbs)DDX series : 2.48 kg (5.5 lbs)Although the effective pixels for the liquid crystal panel is given as 99.99% or more, 0.01% of pixels may not light or may light incorrectly. Specifications subject to change without notice.
is a trademark of SRS Labs, Inc.WOW technology is incorporated under license from SRS Labs, Inc. is a trademark of DVD Format/Logo Licensing Corporation registered in the U.S., Japan and other countries.This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.Manufactured under license from Dolby Laboratories.Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories.Manufactured under license from Dolby Laboratories.Dolby and the double-D symbol are trademarks of Dolby Laboratories.Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks & DTS 2.0 Channel and the DTS logos are trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.The "AAC" logo is a trademark of Dolby Laboratories.The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Kenwood Corporation is under license. Other trademarks and trade names are those of their respective owners.iPod is a trademark of Apple Inc., registered in the U.S. and other countries.iPhone is a trademark of Apple Inc.iTunes is a trademark of Apple Inc.“Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards.“Works with iPhone” means that an electronic accessory has been designed to connect specifically to iPhone and has been certified by the developer to meet Apple performance standards.Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.HD Radio™ and the HD Radio Ready logo are proprietary trademarks of iBiquity Digital Corporation.ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, Inc. This is an official DivX Certified device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video.ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play DivX Video-on-Demand (VOD) content. To generate the registration code, locate the DivX VOD section in the device setup menu. Go to vod.divx.com with this code to complete the registration process and learn more about DivX VOD.DivX®, DivX Certified® and associated logos are registered trademarks of DivX, Inc. and are used under license.Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks & DTS Digital Surround and the DTS logos are trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.DNX9960/ DDX896/ DDX8046BT:DNX7160/ DNX7020EX:FCC WARNINGThis equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.NOTEThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.DNX9960/ DNX7160/ DNX7020EX/ DDX896:IC (Industry Canada) NoticeOperation is subject to the following two conditions:(1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.The term "IC: " before the certification/registration number only signifies that the Industry Canada technical specification were met.This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorateDDX8046BT:The marking of products using lasers CLASS 1 LASER PRODUCTThe label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit.DNX9960/ DNX7160/ DNX7020EX/ DDX896:2CAUTIONUse of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety. Kenwood Corporation 2967-3, ISHIKAWA-MACHI,HACHIOJI-SHITOKYO, JAPANKENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS N0.21 CFR 1040. 10, CHAPTER 1, SUBCHAPTER J.Location : Bottom Panel
This symbol mark indicates that Kenwood manufactured this product so as to decrease harmful infl uence on the environment.

Navigation menu