JVC KENWOOD 422300 VHF Digital Base-Repeater User Manual
JVC KENWOOD Corporation VHF Digital Base-Repeater
User Manual
NXR-710/ NXR-810 VHF DIGITAL BASE-REPEATER/ UHF DIGITAL BASE-REPEATER INSTRUCTION MANUAL BASE-RELAIS NUMÉRIQUE VHF/BASE-RELAIS NUMÉRIQUE UHF MODE D'EMPLOI BASE-REPETIDOR DIGITAL VHF / BASE-REPETIDOR DIGITAL UHF MANUAL DE INSTRUCCTIONES © B62-2199-00 (K) 09 08 07 06 05 04 03 02 01 00 NXR-710 / NXR-810 INSTRUCTION MANUAL VHF DIGITAL BASE-REPEATER / UHF DIGITAL BASE-REPEATER THANK YOU! We are grateful you purchased this Kenwood repeater. We believe this easy-to-program repeater will be highly effective in your communications system, and will keep personnel operating at peak efficiency. ◆ This repeater is intended for use as a fixed base station with the antenna located outdoors on the rooftop or on an antenna tower. u This repeater is designed for a 13.6 V DC power source! Never use a 24 V DC or higher source to power the repeater. ◆ Use only the supplied DC cord. ◆ Do not remove the ferrite core attached to the DC cord. Doing so may cause interference with radio communications. PRECAUTIONS • • • • • Do not expose the unit to rain or moisture; to prevent fire or electric shock. Do not open the unit under any circumstances; to avoid risk of electric shock. Do not expose the unit to long periods of direct sunlight, nor place it close to heating appliances. Do not place the unit in excessively dusty and/or humid areas, nor on unstable surfaces. If you detect an abnormal odor or smoke coming from the unit, disconnect the power from the unit immediately. Contact your Kenwood service center or dealer. UNPACKING AND CHECKING EQUIPMENT Note: The following unpacking information is for use by your Kenwood dealer, an authorized Kenwood service center, or the factory. Carefully unpack the repeater. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately. Item Hardware fixture Front glass Name plates Cushion Cushion Foot Foot Grommet Handle Screws Screws DC cord Lead wire with connector (15 pin) Fuse Instruction Manual NOTICES TO THE USER ◆ Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. ◆ Illegal operation is punishable by fine and/or imprisonment. ◆ Refer service to qualified technicians only. FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. Part Number J21-8559-XX B10-2635-XX B11-1259-XX G13-1801-XX G13-1802-XX J02-0475-XX J02-0492-XX J59-0302-XX K01-0418-XX N30-4006-XX N35-3006-XX E30-3427-XX E31-3228-XX F05-1537-XX B62-2199-XX Quantity INSTALLATION To install the handles onto the front panel of the repeater, align the handles with the holes on the front panel, then secure the handles using the supplied screws. Please consult your dealer for installing the repeater and antenna. MICROPHONE Connect an optional KMC-30, KMC-35, KMC-27A, KMC-27B, or KMC-9C Kenwood microphone to the MIC jack on the front panel. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer for technical assistance. Firmware Copyrights The title to and ownership of copyrights for firmware embedded in Kenwood product memories are reserved for Kenwood Corporation. The AMBE+2TM voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos. #5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084 and #5,195,166. CONTROLS AND FUNCTIONS ■ Front Panel r t CH/STATUS VOLUME TX BUSY POWER MIC q Speaker w CH/STATUS Display Two 7-segment digits display the channel number, name, or status. e VOLUME control Rotate to adjust the audio. r POWER switch t POWER indicator Lights green when power is supplied to the DC 13.6V jack. iu y MIC jack Connect a microphone to this 8-pin modular jack. u Programmable Function keys Press these keys to activate their programmable functions. i BUSY indicator Lights green while a signal is being received. o TX indicator Lights red while transmitting. ■ Rear Panel q w TX OUT r t REF IN RX IN CONTROL I/O FUSE DC 13.6V TEST/SPKR N SYNC q TX OUT jack Connect a TX antenna or a duplexer to this receptacle. w CONTROL I/O jack Connect a repeater controller or a remote panel to this DB‑25 interface. e REF IN jack Connect to a 10 MHz external oscillator. r RX IN jack Connect an RX antenna or a duplexer to this BNC receptacle. t FUSE Insert 15 A blade fuse into this fuse holder. y DC 13.6V jack Connect a 13.6 V DC power supply to this jack. u N SYNC 1 / 2 jack This jack is currently not used . You can connect another repeater here for future functions. i TEST/SPKR jack Test input/output jack. Connect an external speaker to this jack. TRANSCEIVER OPERATION REPEATER OPERATION Note: Please consult your dealer for programming the repeater. ■ Receive When power is applied to the unit, the POWER indicator lights: ・Green when using the main DC jack. Rotate the VOLUME control to adjust the audio. The BUSY indicator lights green while receiving a signal and the TX indicator lights red while transmitting. Adjust the volume to your desired level. You may need to readjust the volume if you are having interference while receiving a message from your dispatcher or another member in your fleet. The BUSY indicator lights green while a signal is being received. ■ Transmit 1 Listen to the channel before transmitting, to make sure it is not being used. 2 Press the microphone PTT switch, then speak in your normal speaking voice. The TX indicator lights red while transmitting. 3 When you finish speaking, release the PTT switch. TERMINAL MIC(Modular Jack) Pin Number Pin Name NC SB GND PTT MICG MIC HOOK NC Description Specification Power Output GND PTT Signal/ TXD2 Asynchronous Send MIC GND MIC Input Hook Detection/ RXD2 Asynchronous Receive Data 13.6V GND I/O Input Impeadance 22kΩ I/O MIC GND 600Ω Input Impeadance 100kΩ I/O notes TEST/SPEAKER CONNECTOR Pin Number 10 11 12 13 14 15 Pin Name SB SB NC GND GND SPG RD RSSI SPI AO1 AO2 SPO AO3 AO4 AO5 Description Specification Power Output Power Output 13.6V 13.6V GND GND Speaker GND RX Audio Output RSSI Signal Output Internal Speaker Input Open Collector Terminal Open Collector Terminal External Speaker Output Open Collector Terminal Open Collector Terminal Open Collector Terminal GND GND Speaker GND 60% Deviation Output Level 0 or 3.3V Short with "SPO" Allowable current value MAX Allowable current value MAX Output Level 4W (5% Distortion) Allowable current value MAX Allowable current value MAX Allowable current value MAX 200mA notes Control I/O (D-SUB 25Pin) CONNECTOR Pin Name NC RXD0 TXD0 AI1 AI2 AI3 DG TD TA RD RA RXG SPM BER_CLK EMON EPTT SC BER_DAT TXG Description Specification I/O 10 11 12 13 14 15 16 17 18 19 Asynchronius Receive Data Asynchronius Send Data Programmable Function Input 1 Programmable Function Input 2 Programmable Function Input 3 Digital GND TX DATA Input TX Audio Input RX DATA Output RX Audio Output RX Signal GND Speaker Mute For Bit Error Rate Clock External Monitor Switch External PTT Switch Squelch Control For Bit Error Rate Data TX Signal GND 20 IO1 Programmable Function I/O 1 21 IO2 Programmable Function I/O 2 22 IO3 Programmable Function I/O 3 23 IO4 Programmable Function I/O 4 24 IO5 Programmable Function I/O 5 25 IO6 Programmable Function I/O 6 Conform to RS-232C standard Conform to RS-232C standard Input Impeadance 47kΩ Input Impeadance 47kΩ Input Impeadance 47kΩ Digital GND Input Impeadance 600Ω Input Impeadance 600Ω 60% Deviation 60% Deviation RX Signal GND Input Impeadance 47kΩ CMOS Input Impeadance 47kΩ Input Impeadance 47kΩ Output Level 0 or 5V CMOS TX Signal GND Input Impeadance 47kΩ/ Output Level 0 or 5V Input Impeadance 47kΩ/ Output Level 0 or 5V Input Impeadance 47kΩ/ Output Level 0 or 5V Input Impeadance 47kΩ/ Output Level 0 or 5V Input Impeadance 47kΩ/ Output Level 0 or 5V Input Impeadance 47kΩ/ Output Level 0 or 5V Pin Number notes signalling voice signalling voice I/O I/O I/O I/O I/O I/O N-SYNC Connector (There are two connectors) Pin Number Pin Name N_SYNC1_B N_SYNC1_A N_SYNC2_B N_SYNC2_A Description Specification I/O notes RS-485 Diffrential Signal B RS-485 Diffrential Signal A RS-485 Diffrential Signal B RS-485 Diffrential Signal A Conform to RS485 Conform to RS485 Conform to RS485 Conform to RS485 I/O I/O I/O I/O Connector#1,2 Connector#1,2 Connector#1,2 Connector#1,2 RX IN TX OUT RX antenna terminal(BNC Receptacle) TX antenna terminal(N Receptacle) REF IN Reference CLK input treminal(BNC Receptacle) MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS • Use only manufacturer or dealer supplied antenna. • Antenna Minimum Safe Distance: 180 cm (6 feet), 50% duty Cycle. • Antenna Gain: 0 dBd referenced to a dipole. The Federal Communications Commission has adopted a safety standard for human exposure to RF (Radio Frequency) energy which is below the OSHA (Occupational Safety and Health Act) limits. • Antenna Mounting: The antenna supplied by the manufacturer or radio dealer must not be mounted at a location such that during radio transmission, any person or persons can come closer than the above indicated minimum safe distance to the antenna, i.e. 180 cm (6 feet) , 50% duty Cycle. • To comply with current FCC RF Exposure limits, the antenna must be installed at or exceeding the minimum safe distance shown above, and in accordance with the requirements of the antenna manufacturer or supplier. • Vehicle installation: The antenna can be mounted at the center of a vehicle metal roof or trunk lid, if the minimum safe distance is observed. • Base Station Installation: The antenna should be fixed-mounted on an outdoor permanent structure. RF Exposure compliance must be addressed at the time of installation. Antenna substitution: Do not substitute any antenna for the one supplied or recommended by the manufacturer or radio dealer. You may be exposing person or persons to excess radio frequency radiation. You may contact your radio dealer or the manufacturer for further instructions. Maintain a separation distance from the antenna to person(s) of at least 180 cm (6 feet) , 50% duty Cycle. You, as the qualified end-user of this radio device must control the exposure conditions of bystanders to ensure the minimum separation distance (above) is maintained between the antenna and nearby persons for satisfying RF Exposure compliance. The operation of this transmitter must satisfy the requirements of Occupational/Controlled Exposure Environment, for work-related use, transmit only when person(s) are at least the minimum distance from the properly installed, externally mounted antenna. Transmit only when people outside the vehicle are at least the recommended minimum lateral distance away from the antenna/vehicle
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : 3.1-702 Instance ID : uuid:3f7e9d47-5f3b-43e4-b839-96dd35abb2bc Document ID : adobe:docid:indd:8a007ace-377d-11dc-ae53-d849516a4d81 Rendition Class : proof:pdf Derived From Instance ID : 8a007acd-377d-11dc-ae53-d849516a4d81 Derived From Document ID : adobe:docid:indd:8a85e9da-e076-11db-bc92-db7be0d0fa05 Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Y Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:bb2c284e-1d33-11dc-9341-0017f20495a0, uuid:062b0a80-9b5b-11dd-8eaa-0017f20495a0, uuid:837b8c53-de9b-11db-86c7-0017f20495a0, uuid:0d40f18f-77fb-11de-87a3-0017f20495a0, uuid:1fbddd89-9784-11de-9e3c-0017f20495a0, uuid:ddaf526f-77fe-11dd-af9b-0017f20495a0 Manifest Reference Document ID : uuid:069B01F51F1111DC90F9CD0FEE86E21A, uuid:C764FBA19D3811DD991FFE6BA3577E9F, uuid:F5F28059E06B11DB9216FAA4D6859FC8, uuid:121390CA792811DEA5F2A9E47FB1BAE6, uuid:121390CC792811DEA5F2A9E47FB1BAE6, uuid:857834A579DC11DD8827F8A267C07720 Create Date : 2009:09:02 14:53:49+09:00 Modify Date : 2009:10:02 14:26:45+09:00 Metadata Date : 2009:10:02 14:26:45+09:00 Creator Tool : Adobe InDesign CS2_J (4.0.5) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 8129 bytes, use -b option to extract) Format : application/pdf Producer : Adobe PDF Library 7.0 Trapped : False Has XFA : No Page Count : 6 Creator : Adobe InDesign CS2_J (4.0.5)EXIF Metadata provided by EXIF.tools