JVC KENWOOD 462500 Intelligent Charger User Manual KSC Y32

JVC KENWOOD Corporation Intelligent Charger KSC Y32

Users Manual

Download: JVC KENWOOD 462500 Intelligent Charger User Manual KSC Y32
Mirror Download [FCC.gov]JVC KENWOOD 462500 Intelligent Charger User Manual KSC Y32
Document ID2308963
Application IDTykrcR0sW+3AUsQFcqxRdw==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize122.07kB (1525905 bits)
Date Submitted2014-06-27 00:00:00
Date Available2014-06-27 00:00:00
Creation Date2014-05-15 13:20:18
Producing SoftwareAcrobat Distiller 10.1.9 (Windows)
Document Lastmod2014-06-12 16:55:41
Document TitleKSC-Y32
Document CreatorAdobe InDesign CS5.5_J (7.5.2)
Document Author: JVC KENWOOD

KSC-Y32
RAPID CHARGER
INSTRUCTION MANUAL
© B62-2558-00 (K)
KSC-Y32 INSTRUCTION MANUAL
RAPID CHARGER
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE,
IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS
VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO
CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT
THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING)
INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
One or more of the following statements may be applicable:
FCC WARNING
This equipment generates or uses radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate this equipment if an unauthorized
change or modification is made.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can generate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
FEATURES
•
•
•
•
Capable of charging Li-ion and Ni-MH battery packs when either attached to or removed from the
transceiver.
Easy to use design allows you to start charging by simply sliding the battery pack into the charging
slot.
Overcharge protection. Protects against reduced battery pack life caused by excessive charging.
After the rapid charge cycle has finished, the charger automatically switches to trickle charge (Ni-MH).
A combination of LED indicator of 3 colors, informs you of the current charging status and battery
pack condition.
SUPPLIED EQUIPMENT
Item
Charger
AC adapter
Instruction manual
Parts number
Quantity
W08-1341-XX
W08-1348-XX
B62-2558-XX
SAFETY PRECAUTIONS
Please read all safety instructions before using this charger. For best results, be aware of all warnings
on the charger, the battery pack, and the product using the battery pack. Follow the provided operating
instructions, and retain them for future reference.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not use in vehicles.
Do not disassemble the charger. Incorrect re-assembly can cause fire or electric shock.
Do not block any ventilation openings, as this may cause smoke or fire.
Keep the charger away from inflammable objects.
Use of attachments/batteries not recommended by nor sold by KENWOOD may cause fire, electric
shock, and/or injury.
Do not insert or drop metal objects (such as clips, etc.) into the charger as this may cause smoke or fire.
Do not expose the charger to rain or moisture, to avoid the risk of fire or electric shock.
If the transceiver and battery pack are wet, do not place them into the charger. Doing so may cause
damage. Before charging, wipe the transceiver and battery pack off with a dry cloth.
Always remove the AC plug from a AC outlet before attempting to inspect or clean the charger.
Removing the battery packs or changing the controls does not remove the AC voltage from the charger.
Position the AC cord so it will not be stepped on, tripped over, nor subjected to damage.
Always remove the AC cord from an AC outlet by pulling on the AC plug rather than the AC cord.
Do not use the charger if it has a damaged AC cord, or if the charger has been damaged in any way.
Contact your KENWOOD dealer to replace or repair the damaged part.
Prevent strong impacts, such as caused by dropping, as the charger can be damaged and/or injuries
may occur.
Do not use the charger in hot or humid environments, in direct sunlight, nor near heaters.
Do not use solvents such as benzene or paint thinner to clean the charger.
Do not turn the charger power on when liquids, such as water or juice, have been dropped into the
charger; applying power at this time may cause fire, smoke, or other damage.
Do not turn the charger power on after the charger has been struck by an item or dropped, as it may
have been damaged during the impact.
Do not short the charging terminals with metal objects.
Use only the supplied AC adapter.
APPROXIMATE CHARGING TIME
Li-ion
Battery Pack
KNB-L1
KNB-L2
KNB-L3
KNB-33L
KNB-47L
KNB-48L
Charging Time
FULL CAPACITY
CHARGING
150 minutes
180 minutes
240 minutes
140 minutes
140 minutes
170 minutes
LONG LIFE
CHARGING
Ni-MH
Battery Pack
KNB-32N
KNB-54N
Charging Time
FULL CAPACITY
CHARGING
170 minutes
170 minutes
LONG LIFE
CHARGING
ORIENTATION
Charging slot
Slide a battery pack or
a transceiver equipped
with a battery pack into
this slot.
PC (Micro USB) port *
The USB connector allows you
to directly connect to a computer
by using a commercially available
USB cable.
LED indicator
Informs you of the
current charger status.
AC adapter jack
Plug in the supplied AC adapter
here.
* By connecting to a PC using a commercially available USB cable (USB 2.0 A Male to Micro B) and
through installing an optional "KAS-12 BATTERY READER", the record of the battery pack equipped
with a data terminal can be monitored during charging.
The USB driver is included with KAS-12.
You can also download the latest driver from URL: http://www2.jvckenwood.com/usb-com/.
(This URL may change without notice.)
ATTENTION:
◆ Use a USB cable shorter than 3 m.
SPECIFICATIONS
AC Voltages
100 V - 240 V AC 50 Hz / 60 Hz
Dimensions (W x H x D) (charger only)
160 x 90 x 58 mm / 6.30 x 3.54 x 2.28 in.
Weight (charger only)
Approx. *** g / *** oz
ATTENTION:
◆ Check the rating label attached to the bottom of the charger for other important specifications.
CHARGING TIPS
•
•
•
•
•
•
•
Using the transceiver while charging its battery pack will interfere with correct charging.
If the operating time of a battery pack decreases although the battery pack is fully and correctly
charged, perform reconditioning if the battery pack is equipped with a data terminal. If the operating
time of the battery pack still decreases, the battery pack life is over. Replace the battery pack.
The ambient temperature should be from 5°C to 40°C (41°F to 104°F) while charging is in progress.
When the ambient temperature is in the upper limits (close to 40°C (104°F)), the charging time may
become longer than normal.
The charging times provided are obtained when a battery pack discharged to 1 V/cell x 6 (Ni-MH) or
3 V/cell x 2 (Li-ion) is charged at normal temperatures. This charging time varies depending on the
degree of discharge and the ambient charging temperature.
Repeatedly recharging a fully charged battery pack, or almost fully charged pack, shortens its
operating time. To resolve this problem, use the pack until it is completely discharged,
1 V/cell x 6 then recharge the pack to full capacity (Ni-MH).
The battery life in charge/discharge cycles is approximately 300-500. However, overcharging and
excessive discharging shortens the battery pack life.
When using this equipment near a radio, transceiver or television, you may experience interference
with reception.
CHARGING PROCEDURE
Do not use in explosive atmospheres (gases, dust, fumes, etc.).
ATTENTION:
◆ Always switch OFF a transceiver equipped with a battery pack before inserting the transceiver into
the charger.
Plug the AC adapter cable into the adapter jack located on the rear
of the charger.
Plug the AC plug into an AC outlet.
Slide a battery pack or a transceiver equipped with a battery pack
into the charging slot.
• Make sure the metal contacts of the battery pack mate securely
with the charger terminals.
• The indicator lights red or blue to charging starts
(refer to the charger status table).
When charging is completed, the indicator flash green. Remove the
battery pack or the transceiver from the charging slot.
• When the charger will not be used for a long time, unplug the
AC adapter from the AC outlet.
CHARGER STATUS TABLE
Indicator Color
Meaning
A battery pack or a transceiver equipped with a battery pack is in the
Red
(FULL CAPACITY CHARGING) charging slot and charging has started.
Flashing red
The battery pack or the charger is defective.
Not light
The battery pack contacts are not properly mated with those of the
charger.
The temperature of the battery pack has not satisfied the charging start
Flashing green and yellow temperature. In this instance, remove the battery until its temperature
increases, then recharge it.
Flashing green
Charging is completed; remove the battery pack or the transceiver from
the charging slot.
Yellow
Reconditioning
Blue
(LONG LIFE CHARGING)
The battery pack will not be fully charged to 100 %. The battery pack is
being charged to approximately 80 %.
•
Flashing purple
•
Flashing red, green, and
yellow repeatedly
If the temperature of the battery pack exceeds the preset
temperature during charging, charging stops and goes into charging
standby mode until the temperature drops within the preset
temperature. Charging will resume automatically if the temperature
of the battery pack drops.
After charging starts, the data of the battery pack is read.
The battery pack has deteriorated. Replace the battery pack with a new
one.
RECONDITIONING (For Ni-MH battery equipped with data terminal only)
■ Automated Battery Reconditioning
When a Ni-MH battery pack equipped with a data terminal is used with this charger, the charger will
read the number of discharging and charging cycle of the battery pack. When the preset number is
reached, reconditioning (full discharging and charging) is performed. This allows you to restore the
charging capacity of the battery pack.
If reconditioning is deemed necessary, reconditioning starts automatically. The LED indicator of the
charger lights up in yellow and discharging starts.
Once the discharging is completed, charging starts automatically and the LED indicator lights up in red.
ATTENTION:
◆ Depending on the usage condition of the battery pack, reconditioning may not be performed even
if the preset number of cycle is reached.
◆ If the preset number of cycle is reached and charging is done on a charger other than KSC-Y32,
reconditioning will be skipped. Reconditioning will not start until the next preset number is reached.
◆ If the effect of the reconditioning is insufficient, reconditioning may start again.
■ Manual Battery Reconditioning
After normal charging starts (indicator lights up in red), the record of the battery pack is read (indicator
blinks 3 times in purple). Within the three blinks in purple, repeating the actions of removing the
battery pack from the charger and placing it back to the charger twice within 5 seconds will force
reconditioning to start.
To start and stop manual
battery reconditioning
■ Stopping Reconditioning Manually
After reconditioning is initiated and when discharging is performed (indicator lights up in yellow),
repeating the actions of removing the battery pack from the charger and placing it back to the
charger twice within 5 seconds will force reconditioning to stop. Normal charging will begin when
reconditioning stops
ATTENTION:
◆ Performing reconditioning frequently may shorten the life-span of the battery.
◆ If reconditioning is initiated manually, remove the battery pack from the charger and place it back
to the charger to resume normal charging operation
LONG LIFE CHARGING MODE (For Li-ion battery equipped with data terminal only)
LONG LIFE CHARGING MODE is a charging mode whereby the battery is charged to approximately 80%
instead of fully charged to 100%.
By connecting to a PC using a commercially available USB cable (USB 2.0 A Male to Micro B) and through
installing an optional "KAS-12 BATTERY READER", you can charge the battery pack in this mode.
Charging the battery pack in this mode repeatedly can extend the life-span of the battery pack.
The LED indicator lights up in blue when charging the battery pack in this mode.
ATTENTION:
◆ The battery pack is not fully charged in this mode so the battery duration from each charging
becomes shorter.


Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Author                          : JVC KENWOOD
Create Date                     : 2014:05:15 13:20:18+09:00
Modify Date                     : 2014:06:12 16:55:41+09:00
Subject                         : B62-2558-00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 10.1.9 (Windows)
Creator Tool                    : Adobe InDesign CS5.5_J (7.5.2)
Metadata Date                   : 2014:06:12 16:55:41+09:00
Format                          : application/pdf
Title                           : KSC-Y32
Creator                         : JVC KENWOOD
Description                     : B62-2558-00
Document ID                     : uuid:eb205de5-8a72-4070-a2fd-64e93ef3f32b
Instance ID                     : uuid:978171e7-bdd3-4c7c-9d70-3a83c72a1a83
Page Layout                     : SinglePage
Page Count                      : 8
EXIF Metadata provided by EXIF.tools
FCC ID Filing: K44462500

Navigation menu