JVC KENWOOD 474601 UHF Digital Base-Repeater User Manual NXR 5700 5800
JVC KENWOOD Corporation UHF Digital Base-Repeater NXR 5700 5800
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2774391 |
| Application ID | c42mMRurUMFjJAHN4oQuiw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 13.77kB (172088 bits) |
| Date Submitted | 2015-10-07 00:00:00 |
| Date Available | 2016-03-26 00:00:00 |
| Creation Date | 2017-09-10 13:06:02 |
| Producing Software | GPL Ghostscript 9.18 |
| Document Lastmod | 2017-09-10 13:06:02 |
| Document Title | NXR-5700_5800 |
| Document Creator | Adobe InDesign CS6 (Windows) |
| Document Author: | JVC KENWOOD Corporation |
NXR-5700 NXR-5800 VHF DIGITAL BASE-REPEATER/ UHF DIGITAL BASE-REPEATER INSTRUCTION MANUAL BASE-RELAIS NUMÉRIQUE VHF/ BASE-RELAIS NUMÉRIQUE UHF MODE D’EMPLOI BASE-REPETIDOR DIGITAL VHF/ BASE-REPETIDOR DIGITAL UHF MANUAL DE INSTRUCCIONES B5A-0713-00 (K,K3,K5) NXR-5700 / NXR-5800 INSTRUCTION MANUAL VHF DIGITAL BASE-REPEATER / UHF DIGITAL BASE-REPEATER THANK YOU! We are grateful you purchased this KENWOOD repeater. We believe this easy-to-program repeater will be highly effective in your communications system, and will keep personnel operating at peak efficiency. KENWOOD incorporates the latest in advanced technology into all of our products. As a result, we feel strongly that you will be pleased with the quality and features of this product. ◆ Do not install the repeater in explosive atmospheres (inflammable gas, dust particles, metallic powders, grain powders, etc.). ◆ This repeater is intended for use as a fixed base station with the antenna located outdoors on the rooftop or on an antenna tower. ◆ This repeater is designed for a 13.6 V DC power source! Never use a 24 V DC or higher source to power the repeater. ◆ Use only the supplied DC cord. ◆ Do not remove the ferrite core attached to the DC cord. Doing so may cause interference with radio communications. PRECAUTIONS • • • • • • • Do not expose the unit to rain or moisture; to prevent fire or electric shock. Do not open the unit under any circumstances; to avoid risk of electric shock. Do not expose the unit to long periods of direct sunlight, nor place it close to heating appliances. Do not place the unit in excessively dusty and/or humid areas, nor on unstable surfaces. Do not put the plastic bag used for packing of this equipment on the place which reaches a small child's hand. It will become a cause of suffocation if it wears flatly. Always switch the transceiver power off before installing optional accessories. If you detect an abnormal odor or smoke coming from the unit, disconnect the power from the unit immediately. Contact your KENWOOD service center or dealer. UNPACKING AND CHECKING EQUIPMENT Note: The following unpacking information is for use by your KENWOOD dealer, an authorized KENWOOD service center, or the factory. Carefully unpack the repeater. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately. Item Front glass Dressed screw Bracket Flat head machine screw Handle DC cord Lead wire with connector (15 pin) Fuse (15 A) SYNC Cable Instruction Manual NOTICES TO THE USER ◆ Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. ◆ Illegal operation is punishable by fine and/or imprisonment. ◆ Refer service to qualified technicians only. Part Number Quantity B10-2781-XX N08-0563-XX J29-0725-XX N32-4008-XX K01-0421-XX E30-3427-XX E31-3228-XX F52-0042-XX E30-7701-XX B5A-0713-XX One or more of the following statements may be applicable: FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved by the party responsible/JVC KENWOOD. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INSTALLATION INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. MICROPHONE To install the handles onto the front panel of the repeater, align the handles with the holes on the front panel, then secure the handles using the supplied screws. Please consult your dealer for installing the repeater and antenna. Connect an optional KMC-30, KMC-35, KMC-9C, or KMC-53 KENWOOD microphone to the MICROPHONE jack on the front panel. OCXO UNIT (KXK-3):Option The OCXO unit (KXK-3) is an Oven Controlled Crystal Oscillator (OCXO) unit. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to The AMBE+2TM voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos. #6,199,037, #6,912,495, #8,200,497, #7,970,606, and #8,359,197. which the receiver is connected. • Consult the dealer for technical assistance. Firmware Copyrights The title to and ownership of copyrights for firmware embedded in KENWOOD product memories are reserved for JVC KENWOOD Corporation. CONTROLS AND FUNCTIONS ■ Front Panel STATUS 1 2 3 4 5 6 7 8 VOLUME TAKE RPT MON OVER DISABLE CTRL OCXO BUSY TX POWER OFF/ MICROPHONE l k j ih a Speaker b CH/STATUS Display Two 17-segment digits display the channel number, name, or status. c STATUS indicator Indicates the status of the repeater. (NXDN mode) Programmable Function keys Press these keys to activate their programmable functions. e USB jack (B-Type) Connect to the PC using a USB cable. f VOLUME control Turn clockwise until a click sounds, to unmute the audio. Rotate to adjust the audio. Turn counterclockwise fully to mute the audio. g MICROPHONE jack Connect a microphone to this 8-pin modular jack. h POWER indicator Lights green when power is supplied to the DC 13.6V jack. Blinks red when an abnormal voltage is present. While blinking, the repeater cannot be used. i TX indicator Lights red while transmitting. j BUSY indicator Lights green while a signal is being received. k OCXO indicator The OCXO indicator shows the state of the reference 10 MHz oscillator : Lights Green when using a reference signal from an optional OCXO unit (KXK-3). Lights Orange when using a reference signal from another repeater. Lights red when no reference signal is available or when an error occurs. Does not light when the reference signal is an internal VCXO signal. l CTRL indicator The CTRL indicator shows the control channel status while using Digital trunking : Lights Green when the repeater is used as control channel. Blinks Green when using a non-dedicated control channel. ■ Rear Panel TEST/SPKR CONTROL I/O SYNC LAN REF OUT FUSE DC 13.6V REF IN 15A RX TX a RX IN jack Connect an RX antenna or a duplexer to this BNC receptacle. b TEST/SPKR jack Test input/output jack. Connect an external speaker to this jack. c CONTROL I/O jack Connect a repeater controller or a remote panel to this DB-25 interface. SYNC 1 / 2 jack Connect to another repeater to use synchronous frame signaling for digital trunking. e LAN jack Connect to Ethernet. f REF OUT jack Connect to another repeater within the site to supply a reference signal. g REF IN jack Connect from another repeater within the site to receive a reference signal. h FUSE Insert 15 A blade fuse into this fuse holder. i DC 13.6V jack Connect a 13.6 V DC power supply to this jack. j TX OUT jack Connect a TX antenna or a duplexer to this BNC receptacle. TRANSCEIVER OPERATION REPEATER OPERATION ■ Receive Note: Please consult your dealer for programming the repeater. Due to the frequency stability on the 6.25 kHz bandwidth channel, when operating the repeater using an optional OCXO unit, allow the unit to warm up after turning the power on. Refer to the KXK-3 instruction manual concerning the warm up duration. After turning on the power, wait for approximately 10 seconds for the VCXO or 5 minutes for the OCXO (when mounting) to warm up. During this time, the CH/STATUS Display will blink. The keys will function when they are pressed. Adjust the volume to your desired level. You may need to readjust the volume if you are having interference while receiving a message from your dispatcher or another member in your fleet. The BUSY indicator lights green while a signal is being received. ■ Transmit When power is applied to the unit, the POWER indicator lights green. Turn the VOLUME control clockwise until a click sounds, to unmute the audio. Rotate to adjust the audio. Turn the VOLUME control counterclockwise fully to mute the audio. The BUSY indicator lights green while receiving a signal and the TX indicator lights red while transmitting. 1 Listen to the channel before transmitting, to make sure it is not being used. 2 Press the microphone PTT switch, then speak in your normal speaking voice. The TX indicator lights red while transmitting. 3 When you finish speaking, release the PTT switch. © 2015 Addendum Terminal Description Control I/O (D-SUB 25 Pin) CONNECTOR MIC (Modular Jack) Pin NO. Pin Name NC SB GND Description Specification I/O Notes Pin NO. Pin Name Description Specification I/O Not used − NC Not used Not used Power Output 13.6 V RXD Asynchronous Receive Data Comform to RS-232C standard GND GND − TXD Asynchronous Send Data Comform to RS-232C standard Not used PTT PTT Signal Input Impedance 100 k AI1 Programmable Function Input 1 Input Impedance 47 k MICG MIC GND MIC GND − AI2 Programmable Function Input 2 Input Impedance 47 k MIC MIC Input 600 AI3 Programmable Function Input 3 Input Impedance 47 k HOOK Hook Detection Input Impeadance 100 k DG Digital GND Digital GND − NC Not used Not used − USB (USB Type-B) Pin NO. Pin Name Description Specification I/O VBUS USB VBUS Conform to USB specification D- USB Data minus Conform to USB specification I/O D+ USB Data plus Conform to USB specification I/O GND USB GND USB GND Notes − TEST/ SPEAKER CONNECTOR Pin NO. Pin Name Description Specification I/O Notes Notes − TD TX Data Input Input Impedance 600 not Pre-emphasis TA TX Audio Input Input Impedance 600 Pre-emphasis 10 RD RX Data Output Load Impedance 4.7 k not De-emphasis 11 RA RX Audio Output Load Impedance 4.7 k De-emphasis 12 RXG RX Signal GND RX Signal GND − 13 SPM Speaker Mute Input Impedance 47 k 14 BER CLK For Bit Error Rate Clock CMOS 15 EMON External Monitor Switch Input Impedance 47 k 16 EPTT External PTT Switch Input Impedance 47 k 17 SC Squelch Control Output level 0 or 5 V 18 BER DAT For Bit Error Rate Data CMOS 19 TXG TX Signal GND TX Signal GND − SB Power Output 13.6 V 20 IO1 Programmable Function I/O 1 Input Impedance 47 k I/O Output level 0 or 5 V SB Power Output 13.6 V 21 IO2 Programmable Function I/O 2 Input Impedance 47 k I/O Output level 0 or 5 V NC Not used Not used − 22 IO3 Programmable Function I/O 3 Input Impedance 47 k I/O Output level 0 or 5 V GND GND GND − 23 IO4 Programmable Function I/O 4 Input Impedance 47 k I/O Output level 0 or 5 V GND GND GND − 24 IO5 Programmable Function I/O 5 Input Impedance 47 k I/O Output level 0 or 5 V SPG Speaker GND Speaker GND − 25 IO6 Programmable Function I/O 6 Input Impedance 47 k I/O Output level 0 or 5 V RD RX Data Output Allowable load MIN 100 k RSSI RSSI Signal Output Output Level 0 to 5 V SPI Internal Speaker Input Short with "SPO" Open Collector Terminal Allowable current value MAX 200 mA 10 AO1 11 AO2 Open Collector Terminal Allowable current value MAX 200 mA 12 SPO External Speaker Output Output Level 3W (5%Distortion) 13 AO3 Open Collector Terminal Allowable current value MAX 200 mA 14 AO4 Open Collector Terminal Allowable current value MAX 200 mA 15 AO5 Open Collector Terminal Allowable current value MAX 200 mA not De-emphasis LAN (Modular Jack) Pin NO. Pin Name Description Specification I/O Notes TD+ TX Signal + Comform to IEEE802.3 standard 100 Mbps TD- TX Signal − Comform to IEEE802.3 standard 100 Mbps RD+ RX Signal + Use Designated Transformer 100 Mbps NC Not used Not used − NC Not used Not used − RD- RX Signal − Use Designated Transformer NC Not used Not used − NC Not used Not used − 100 Mbps SYNC 1, 2 Connector (There are two connectors) Pin NO. Pin Name Description Specification FRMA RS-485 Differential Signal A Conform to RS485 NC Not used Not used NC Not used Not used FRMB RS-485 Differential Signal B Conform to RS485 RX ANT TX ANT Impedance 50 Impedance 50 REF IN REF OUT External Reference Signal Input (10 MHz). Impedance : more than 1 k Reference Signal Distribution (10 MHz). Load Impedance : more than 50 I/O Notes I/O − − I/O B5K-0197-00 MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS • Use only manufacturer or dealer supplied antennas. • Antenna Minimum Safe Distance: 180 cm (6 feet). • Antenna Gain: 0 dBd referenced to a dipole. The Federal Communications Commission has adopted a safety standard for human exposure to RF (Radio Frequency) energy which is below the OSHA (Occupational Safety and Health Act) limits. • Antenna Mounting: The antenna supplied by the manufacturer or radio dealer must not be mounted at a location such that during radio transmission, any person or persons can come closer than the above indicated minimum safe distance to the antenna, i.e. 180 cm (6 feet). • To comply with current FCC RF Exposure limits, the antenna must be installed at or exceeding the minimum safe distance shown above, and in accordance with the requirements of the antenna manufacturer or supplier. • Vehicle installation: The antenna can be mounted at the center of a vehicle metal roof or trunk lid, if the minimum safe distance is observed. • Base Station Installation: The antenna should be ixed-mounted on an outdoor permanent structure. RF Exposure compliance must be addressed at the time of installation. Antenna substitution: Do not substitute any antenna for the one supplied or recommended by the manufacturer or radio dealer. You may be exposing person or persons to excess radio frequency radiation. You may contact your radio dealer or the manufacturer for further instructions. Maintain a separation distance from the antenna to person(s) of at least 180 cm (6 feet). You, as the qualiied end-user of this radio device must control the exposure conditions of bystanders to ensure the minimum separation distance (above) is maintained between the antenna and nearby persons for satisfying RF Exposure compliance. The operation of this transmitter must satisfy the requirements of Occupational/Controlled Exposure Environment, for work-related use, transmit only when person(s) are at least the minimum distance from the properly installed, externally mounted antenna. Transmit only when people outside the vehicle are at least the recommended minimum lateral distance away from the antenna/vehicle. B59-2667-00
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V4.4 (128-bit) User Access : Print, Print high-res Author : JVC KENWOOD Corporation Create Date : 2015:09:08 11:44:43+09:00 Modify Date : 2015:09:18 15:21:24+09:00 Subject : B5A-0713-00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Creator : JVC KENWOOD Corporation Description : B5A-0713-00 Title : NXR-5700_5800 Creator Tool : Adobe InDesign CS6 (Windows) Metadata Date : 2015:09:18 15:21:24+09:00 Keywords : Producer : iTextSharp™ 5.5.0 ©2000-2013 iText Group NV (AGPL-version); modified using iTextSharp™ 5.5.0 ©2000-2013 iText Group NV (AGPL-version) Document ID : uuid:822d3af7-44b6-4072-a3be-61767cbf7fb1 Instance ID : uuid:d667b856-d898-4747-8f92-b85127165e9f Page Layout : SinglePage Page Count : 6EXIF Metadata provided by EXIF.tools