JVC CA MXGA77 MXGT88/MXGA77[B] User Manual MXGA77, MXGT88 LVT1010 003B
CA-MXGT88 CA-MXGT88 LVT1010-003B English,
User Manual: JVC CA-MXGA77 CA-MXGA77, CA-MXGT88 English,
Open the PDF directly: View PDF .
Page Count: 36
Download | |
Open PDF In Browser | View PDF |
COMPACT COMPONENT SYSTEM CA-MXGT88 CA-MXGA77 CA-MXGT88 CD 1 CA-MXGA77 CD 2 CD 3 CD 1 CD 2 CD 3 DISC CHANGE DISC CHANGE STANDBY STANDBY ECO ECO COMPACT COMPONENT SYSTEM MX-GT88 COMPACT COMPONENT SYSTEM MX-GA77 REC START / STOP R O C K D A N C E REPEAT REC START / STOP R O C K D A N C E REPEAT CD REC START P O P H A L L PROGRAM CD REC START P O P H A L L PROGRAM DUBBING CLASSIC STADIUM RANDOM DUBBING CLASSIC STADIUM RANDOM VOLUME DISPLAY PHONES UND MODE SO PRESET CLOCK / TIMER DISPLAY SET PHONES VOLUME CLOCK / TIMER UND MODE SO PRESET SET CANCEL / DEMO SOUND TURBO CANCEL / DEMO SOUND TURBO TAPE A / B TAPE A / B SELECT DISPLAY MODE RDS MODE SELECT DISPLAY MODE RDS MODE SUBWOOFER LEVEL SUBWOOFER LEVEL TUNING TUNING TUNING BEEP TUNING BEEP MP3 MP3 EJECT EJECT EJECT EJECT INSTRUCTIONS For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Model No. Serial No. LVT1010-003B [B] Cover_MXGT88&GA77[B]B.pm6 1 03.2.28, 9:40 AM Warnings, Cautions and Others IMPORTANT FOR LASER PRODUCTS IMPORTANT for the U.K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. REPRODUCTION OF LABELS 1 CLASSIFICATION LABEL, PLACED ON EXTERIOR SURFACE BE SURE to replace the fuse only with an identical approved type, as originally fitted. If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. If this product is not supplied fitted with a mains plug then follow the instructions given below: IMPORTANT: 2 WARNING LABEL, PLACED INSIDE THE UNIT DO NOT make any connection to the terminal which is marked with the letter E or by the safety earth symbol or coloured green or green-and-yellow. The wires in the mains lead on this product are coloured in accordance with the following code: Blue : Neutral Brown : Live As these colours may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN. switch! Caution –– Disconnect the mains plug to shut the power off completely. The switch in any position does not disconnect the mains line. The power can be remote controlled. CAUTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, covers or cabinet. 2. Do not expose this appliance to rain or moisture. CAUTION: Invisible laser radiation when open and interlock failed or defeated. AVOID DIRECT EXPOSURE (e) TO BEAM. VARNING: Osynlig laserstrålning när denna del är öppnad och spärren är urkopplad. Betrakta ej (s) strålen. ADVARSEL: Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsæt(d) telse for stråling VARO: Avattaessa ja suojalukitus ohitettaessa olet alttiina näkymättömälle lasersäteilylle. Älä katso (f) säteeseen. 1. CLASS 1 LASER PRODUCT 2. CAUTION: Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam. 3. CAUTION: Do not open the top cover. There are no user serviceable parts inside the Unit; leave all servicing to qualified service personnel. CAUTION • Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.) • Do not place any naked flame sources, such as lighted candles, on the apparatus. • When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly. • Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Caution: Proper Ventilation To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows: 1 Front: No obstructions and open spacing. 2 Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below. 3 Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more. Side view Front view 15 cm 1 cm 15 cm 1 cm 15 cm 15 cm CA-MXGT88 15 cm CA-MXGA77 CA-MXGA77 10 cm G-1 Safety_MXGT88&GA77[B].pm6 1 CA-MXGT88 03.2.8, 9:01 PM SAFETY INSTRUCTIONS “SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT” This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. ✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮ Do read the operating instructions before you attempt to use the equipment. Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or changing connections. Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment. Do be careful with glass panels or doors on equipment. ✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮ DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way–switch off, withdraw the mains plug and consult your dealer. DON’T remove any fixed cover as this may expose dangerous voltages. DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a standby mode. Switch off using the switch on the equipment and make sure that your family know how to do this. Special arrangements may need to be made for infirm or handicapped people. DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is illegal to watch television whilst driving. DON’T listen to headphones at high volume as such use can permanently damage your hearing. DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings. Overheating will cause damage and shorten the life of the equipment. DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit the manufacturer’s approved stand or legs with the fixings provided according to the instructions. DON’T allow electrical equipment to be exposed to rain or moisture. ABOVE ALL — NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case -this could result in a fatal electrical shock.; — NEVER guess or take chances with electrical equipment of any kind — it is better to be safe than sorry! G-2 Safety_MXGT88&GA77[B].pm6 2 03.2.8, 9:01 PM Introduction We would like to thank you for purchasing one of our JVC products. Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance from your unit, and retain this manual for future reference. About This Manual Power sources This manual is organized as follows: • When unplugging from the wall outlet, always pull the plug, not the AC power cord. • The manual mainly explains operations using the buttons and controls on the unit. You can also use the buttons on the remote control if they have the same or similar names (or marks) as those on the unit. If operation using the remote control is different from that using the unit, it is then explained. • Basic and common information that is the same for many functions is grouped in one place, and is not repeated in each procedure. For instance, we do not repeat the information about turning on/off the unit, setting the volume, changing the sound effects, and others, which are explained in the section “Common Operations” on pages 9 to 11. • The following marks are used in this manual: Gives you warnings and cautions to prevent damage or risk of fire/electric shock. Also gives you information which is not good for obtaining the best possible performance from the unit. Gives you information and hints you had better know. DO NOT handle the AC power cord with wet hands. Moisture condensation Moisture may condense on the lens inside the unit in the following cases: • After starting heating in the room • In a damp room • If the unit is brought directly from a cold to a warm place Should this occur, the unit may malfunction. In this case, leave the unit turned on for a few hours until the moisture evaporates, unplug the AC power cord, and then plug it in again. Others • Should any metallic object or liquid fall into the unit, unplug the unit and consult your dealer before operating any further. • If you are not going to operate the unit for an extended period of time, unplug the AC power cord from the wall outlet. DO NOT disassemble the unit since there are no user serviceable parts inside. Precautions If anything goes wrong, unplug the AC power cord and consult your dealer. Installation • Do not grasp the control knobs when moving or carrying the unit. • Install in a place which is level, dry and neither too hot nor too cold—between 5˚C and 35˚C. • Install the unit in a location with adequate ventilation to prevent internal heat built-up in the unit. • Leave sufficient distance between the unit and the TV. • Keep the speakers away from the TV to avoid interference with TV. DO NOT install the unit in a location near heat sources, or in a place subject to direct sunlight, excessive dust or vibration. 1 01_08MXGT88&GA77[B].pm6 1 03.2.8, 9:01 PM Contents Location of the Buttons and Controls ....................... 3 Front Panel ................................................................. 3 Remote Control .......................................................... 5 Getting Started ............................................................ 6 Unpacking .................................................................. 6 Putting the Batteries into the Remote Control ........... 6 Connecting Antennas ................................................. 6 Connecting Speakers .................................................. 7 Connecting Other Equipment ..................................... 8 Canceling the Display Demonstration ....................... 8 Common Operations .................................................. 9 Turning On or Off the Power ....................................... 9 Saving the Power Consumption While on Standby —ECO Mode ........................................................ 9 Setting the Clock ........................................................ 9 Selecting the Sources ................................................... 9 Adjusting the Volume ............................................... 10 Reinforcing the Bass Sound ..................................... 10 Enjoying the Heavy Sound ....................................... 10 Selecting the Sound Modes ...................................... 11 Turning On or Off the Key-touch Tone .................... 11 Listening to the Radio .............................................. 12 Tuning in to a Station—Auto Search ....................... 12 Presetting Stations .................................................... 12 Tuning in to a Preset Station .................................... 12 Receiving FM Stations with RDS ............................ 13 Changing the RDS Information ............................... 13 Searching for Programs by PTY Codes (PTY Search) ...................................................... 13 Switching Temporarily to a Program Type of Your Choice .................................................... 14 Playing Back CDs ..................................................... 15 Loading CDs ............................................................ Playing Back CDs—All Disc and One Disc ............ Basic CD Operations ................................................ Changing the MP3 Playback Mode.......................... Turning On or Off the Resume Play for MP3 Disc .. Programming the Playing Order of the Tracks —Program Play .................................................. Playing at Random—Random Play ......................... Repeating Tracks or CDs—Repeat Play .................. Prohibiting Disc Ejection—Carrousel Lock ............ 15 15 17 19 19 20 21 21 21 Playing Back Tapes ................................................... 22 Playing Back a Tape ................................................. 22 Recording .................................................................. 23 Recording a Tape on Deck B .................................... 23 Dubbing Tapes .......................................................... 24 CD Synchronized Recording ..................................... 24 Using the Timers ....................................................... 25 Using Daily Timer .................................................... Using Recording Timer ............................................ Using Sleep Timer .................................................... Timer Priority ........................................................... 25 27 28 28 Maintenance .............................................................. 29 Additional Information ............................................ 30 Troubleshooting ........................................................ 31 Specifications ............................................................. 32 2 01_08MXGT88&GA77[B].pm6 2 03.2.8, 9:01 PM Location of the Buttons and Controls Become familiar with the buttons and controls on your unit. Front Panel CD 1 CD 2 u i o CD 3 DISC CHANGE STANDBY 1 ECO 2 3 4 5 6 7 REC START / STOP R O C K D A N C E REPEAT CD REC START P O P H A L L PROGRAM DUBBING CLASSIC STADIUM RANDOM VOLUME DISPLAY PHONES CLOCK / TIMER UND MODE SO 8 9 p q PRESET CANCEL / DEMO SOUND TURBO TAPE A / B SELECT DISPLAY MODE RDS MODE SUBWOOFER LEVEL w a s d f g h j TUNING TUNING BEEP e r t k l EJECT EJECT / y 3 01_08MXGT88&GA77[B].pm6 SET ; 3 03.2.8, 9:01 PM Continued Display Window 1 2 3 4 GROUP TRACK RDS 5 6 7 NEWS INFO 89 0 MP3 PRGM ! = ~ RANDOM TURBO WOOFER REPEAT ALL 1 DISC MONO ST SOUND MODE @ # $ % See pages in the parentheses for details. Front Panel 1 2 3 4 5 6 7 8 9 p q w e r t y u i o ; a s d (standby/on) button and STANDBY lamp (9, 26, 27) ECO button (9) Carrousel Sound mode lamps (11) REC START/STOP button (23) CD REC START button (24) DUBBING button (24) Display window DISPLAY button (9) Remote sensor PHONES jack (10) SOUND MODE control (11) SOUND TURBO button (10) SUBWOOFER LEVEL +/– buttons (10) 7 (stop) button (15 – 17, 20 – 24) BEEP button (11) AUX button (9) Pressing this button also turns on the unit. FM/AM button (9, 12) Pressing this button also turns on the unit. TUNING +/– buttons (12) 1/¡ (fast rewind/fast forward) buttons (17, 22) Deck A cassette holder (22, 24) Pressing the 0 EJECT portion opens the holder. Disc number buttons and lamps (CD1, CD2, and CD3) (16, 17, 20, 21, 24) Pressing one of these buttons also turns on the unit. 0 (Carrousel open/close) button (15 – 17, 19 – 21) Pressing this button also turns on the unit. DISC CHANGE button (15, 17) REPEAT button (15, 17, 21) PROGRAM (MP3 Resume on/off) button (19, 20) RANDOM button (21) CLOCK/TIMER button (9, 25 – 28) SET button (9, 12, 20, 25 – 28) CANCEL/DEMO button (8, 9, 20, 25 – 28) f PRESET +/– control (12) 4/¢ (reverse search/forward search) control (9, 17 – 21, 25 – 27) g TAPE A/B button (22) h VOLUME control (10) j RDS operation buttons (13, 14) • DISPLAY MODE, RDS MODE, and SELECT +/– buttons k TAPE 3 (play) button (9, 22, 24) Pressing this button also turns on the unit. l CD 6 (play/pause) button (9, 15 – 17, 20) Pressing this button also turns on the unit. / Deck B cassette holder (22 – 24, 27) Pressing the EJECT 0 portion opens the holder. Display window 1 Timer indicators • DAILY (daily timer), SLEEP (sleep timer), REC (recording timer), and (timer) indicators 2 GROUP indicator 3 TRACK indicator 4 RDS indicator 5 Main display • Shows the source name, frequency, etc. 6 NEWS indicator 7 INFO indicator 8 MP3 indicator 9 Tape operation indicators • A/B (operating deck), REC (recording), and 2 3 (tape running) indicators 0 PRGM (program) indicator - SOUND MODE indicator = WOOFER indicator ~ TURBO indicator ! CD track number indicators @ RANDOM indicator # REPEAT mode indicators • REPEAT, 1, 1 DISC, ALL DISC indicators $ Tuner operation indicators • MONO and ST (stereo) indicators % Volume level, Subwoofer level and Sound Mode pattern indicators 4 01_08MXGT88&GA77[B].pm6 4 03.2.8, 9:01 PM Remote Control Remote Control 1 2 w 1 2 3 4 5 6 7 8 3 e MP3 4 5 6 r t y u i 7 8 9 p q o ; a s 9 p q w e r t y u i o ; a s CD 1 CD 2 BEEP ON/OFF button (11) SLEEP button (28) Number buttons (12, 18) SOUND TURBO button (10) VOLUME + button (10) 4/1 (reverse search/fast rewind) button (12, 17 – 19, 21, 22) SUBWOOFER LEVEL – button (10) AUX button (9) Pressing this button also turns on the unit. FADE MUTING button (10) FM/AM button (9, 12) Pressing this button also turns on the unit. CD 6 (play/pause) button (9, 15 – 17, 20) Pressing this button also turns on the unit. STANDBY/ON button (9) FM MODE button (12) MP3 button (19) SOUND MODE button (11) 7 (stop) button (15 – 17, 20 – 24) ¢/¡ (forward search/fast forward) button (12, 17 – 19, 21, 22) VOLUME – button (10) SUBWOOFER LEVEL + button (10) A/B button (22) TAPE 3 (play) button (9, 22) Pressing this button also turns on the unit. DISC SKIP button (15, 17) RDS operation buttons (13, 14) • DISPLAY MODE, SELECT +/–, and RDS MODE buttons CD 3 DISC CHANGE STANDBY ECO REC START / STOP R O C K D A N C E REPEAT CD REC START P O P H A L L PROGRAM DUBBING CLASSIC STADIUM RANDOM VOLUME DISPLAY PHONES CLOCK / TIMER UND MODE SO PRESET SET CANCEL / DEMO SOUND TURBO TAPE A / B SELECT DISPLAY MODE RDS MODE SUBWOOFER LEVEL TUNING TUNING BEEP EJECT EJECT When using the remote control, point it at the remote sensor on the front panel. 5 01_08MXGT88&GA77[B].pm6 5 03.2.8, 9:01 PM Getting Started Continued Unpacking Connecting Antennas After unpacking, check to be sure that you have all the following items. The number in the parentheses indicates the quantity of the pieces supplied. FM antenna FM antenna (supplied) A • • • • NN NTE A AM (MW) loop antenna (1) FM antenna (1) Remote control (1) Batteries (2) 5 FM [7 AM ] If any is missing, consult your dealer immediately. Putting the Batteries into the Remote Control Insert the batteries—R6P(SUM-3)/AA(15F)—into the remote control, by matching the polarity (+ and –) on the batteries with the + and – markings on the battery compartment. When the remote control can no longer operate the unit, replace both batteries at the same time. 1 Attach the FM antenna to the FM [75 Ω] coaxial terminal. 2 Extend the FM antenna. 3 Fasten it up in the position which gives you the best reception, then fix it on the wall, etc. 1 About the supplied FM antenna The FM antenna supplied with this unit can be used as temporary measure. If reception is poor, you can connect an outdoor FM antenna. To connect an outdoor FM antenna Before connecting it, disconnect the supplied FM antenna. 2 R6P(SUM-3)/AA(15F) Outdoor FM antenna (not supplied) 3 A ENN ANT AM ] M [75 F • • • • DO NOT use an old battery together with a new one. DO NOT use different types of batteries together. DO NOT expose batteries to heat or flame. DO NOT leave the batteries in the battery compartment when you are not going to use the remote control for an extended period of time. Otherwise, it will be damaged from battery leakage. A 75 Ω antenna with coaxial type connector (DIN 45325) should be used. 6 01_08MXGT88&GA77[B]B.pm6 6 03.2.28, 9:40 AM Connecting Speakers AM (MW) antenna 1 2, 3 1 Vinyl-covered wire (not supplied) ANTENNA AM FM [ 75 ] 2, 3 Speaker cord (blue/black) Black MAIN SPEAKER [ 4-8 ] L R R Black Speaker cord (blue/black) From right main speaker’s terminals AM (MW) loop antenna (supplied) on the rear of the unit. 2 Insert the end of the AM (MW) loop antenna cord into the terminal. • If the AM (MW) loop antenna wire is covered with vinyl, remove the vinyl by twisting it as shown in the diagram. 3 Release the finger from the clamp. 4 Turn the AM (MW) loop antenna until you have the best reception. To connect an outdoor AM (MW) antenna When reception is poor, connect a single vinyl-covered wire to the AM terminal and extend it horizontally. (The AM (MW) loop antenna must remain connected.) For better reception of both FM and AM (MW) • Make sure the antenna conductors do not touch any other terminals and connecting cords. • Keep the antennas away from metallic parts of the unit, connecting cords, and the AC power cord. 7 Red Speaker cord (red/black) From right subwoofer’s terminals From left subwoofer’s terminals From left main speaker’s terminals 1 Press and hold the clamp of the speaker terminal on the rear of the unit. 2 Insert the end of the speaker cord into the terminal. Match the colors (polarity): Blue (+) to blue (+) and black (–) to black (–); red (+) to red (+) and black (–) to black (–). • If the wire is covered with vinyl, remove the vinyl by twisting it as shown in the diagram. 3 Release the finger from the clamp. IMPORTANT: • Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the unit. • DO NOT connect more than one speaker to one speaker terminal. 7 01_08MXGT88&GA77[B].pm6 SUBWOOFER [ 6 -16 ] L Blue 1 Press and hold the clamp of the AM terminal Speaker cord (red/black) 03.2.8, 9:01 PM Connecting Other Equipment NOW you are ready to plug in the unit and other connected equipment. You can connect audio equipment—used only as a playback device. • DO NOT connect any equipment while the power is on. • DO NOT plug in any equipment until all connections are complete. Canceling the Display Demonstration When connecting the AC power cord into a wall outlet, the unit automatically starts the display demonstration. To connect audio equipment On the unit ONLY: Be sure that the plugs of the audio cords are color coded: White plugs and jacks are for left audio signals, and red ones for right audio signals. To cancel the display demonstration, press CANCEL/DEMO while the display demonstration is shown on the display. AUX IN CANCEL / DEMO When you press other buttons The display demonstration stops temporarily. It will start automatically again (if no operation is done for 2 minutes) until you cancel it. To start the display demonstration manually Press and hold CANCEL/DEMO again for more than 2 seconds. CANCEL / DEMO Audio equipment To audio output For playing the other equipment through this unit, connect between the audio output jacks on the other equipment and AUX IN jacks by using audio cords (not supplied). 8 01_08MXGT88&GA77[B].pm6 8 03.2.8, 9:01 PM Common Operations 2 Turn the 4/¢ control to adjust Turning On or Off the Power To turn on the unit, press STANDBY lamp goes off. the hour, then press SET. so that the STANDBY ECO SET To turn off the unit (on standby), press again so that the STANDBY lamp lights up. STANDBY ECO A little power is always consumed even while the unit is on standby. To switch off the power supply completely, unplug the AC power cord from the AC outlet. The minute digits start flashing on the display. • If you want to correct the hour after pressing SET, press CANCEL/DEMO. The hour digits start flashing again. 3 Turn the 4/¢ control to adjust the minute, then press SET. When you unplug the AC power cord or if a power failure occurs The clock is reset to “– – : – –” soon, while the tuner preset stations (see page 12) will be erased in a few days. Saving the Power Consumption While on Standby—ECO Mode To check the clock time You can save the power consumption while the unit is turned off (on standby). To activate the ECO mode, press ECO while the unit is turned off (on standby). The display illumination (including the display demonstration) disappears. SET Press DISPLAY while playing any source. • Each time you press the button, the source indication and the clock time alternate on the display. DISPLAY STANDBY ECO To deactivate the ECO mode, press ECO again. The display illumination appears. • Turning on the unit also deactivates the ECO mode. To adjust the clock again If you have adjusted the clock before, you need to press CLOCK/TIMER repeatedly until “CLOCK” is selected. • Each time you press the button, the clock/timer setting modes change as follows: DAILY REC ON TIME (Daily Timer) Canceled CLOCK ON TIME (Recording Timer) About the ECO mode While the ECO mode is activated, the display demonstration is canceled temporarily. If there is a power failure The clock loses the setting and is reset to “– – : – –.” You need to set the clock again. Setting the Clock Before operating the unit any further, first set the clock built in this unit. You can set the clock whether the unit is on or off. On the unit ONLY: 1 Press CLOCK/TIMER. The hour digits start flashing on the display. Selecting the Sources To listen to the radio, press FM/AM. (See page 12.) To play back CDs, press CD 6. (See pages 15 – 21.) To play back tapes, press TAPE 3. (See page 22.) To select the external equipment as the source, press AUX. CLOCK / TIMER When you press the play button for a particular source (AUX, FM/AM, CD 6, and TAPE 3), the unit turns on (and the unit starts playing the source if it is ready—COMPU PLAY CONTROL). 9 09_10MXGT88&GA77[B].pm6 9 03.2.8, 9:01 PM Continued Adjusting the Volume Reinforcing the Bass Sound You can adjust the volume level only while the unit is turned on. This function only affects the playback sound, not your recording. This function only affects the playback sound, not your recording. Turn the VOLUME control clockwise to increase the volume or counterclockwise to decrease it. • The volume level can be adjusted in 32 steps (VOL MIN, VOL 1 — VOL 30, and VOL MAX). VOLUME Press SUBWOOFER LEVEL + to increase the subwoofer sound or SUBWOOFER LEVEL – to decrease it. • The subwoofer level can be adjusted in 3 steps (LEVEL 1 — LEVEL 3). If you press SUBWOOFER LEVEL + to increase the level up to LEVEL 3, “MAX LEVEL” appears on the display. SUBWOOFER LEVEL WOOFER indicator also shows the current subwoofer level. When using the remote control, press VOLUME + to increase the volume or press VOLUME – to decrease it. WOOFER For private listening Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on headphones. Enjoying the Heavy Sound DO NOT turn off (on standby) the unit with the volume set to an extremely high level; otherwise, a sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the unit or start playing any source next time. REMEMBER you cannot adjust the volume level while the unit is on standby. To turn down the volume level temporarily Press FADE MUTING on the remote control. The volume level gradually decreases to “VOL MIN.” To restore the sound, press the button again. You can enjoy the heavy sound by using the sound turbo. The function boosts the low and high frequency sound. This function only affects the playback sound, not your recording. Press SOUND TURBO. The TURBO indicator lights up on the display. • Each time you press SOUND TURBO, the sound turbo turns on and off alternately. SOUND TURBO TURBO indicator TURBO WOOFER When you turn off the sound turbo The subwoofer level is set to LEVEL 1. When the sound turbo is on Turning the SOUND MODE control (or pressing SOUND MODE on the remote control) cancels the sound turbo. 10 09_10MXGT88&GA77[B].pm6 10 03.2.8, 9:01 PM Selecting the Sound Modes This function only affects the playback sound, not your recording. You can select one of the 6 preset sound modes (3 surround modes and 3 SEA—Sound Effect Amplifier—modes). When using the remote control, press SOUND MODE to select the sound mode. • Each time you press the button, the sound modes change as follows: D.CLUB HALL STADIUM ROCK (Dance CLUB) OFF (Canceled) CLASSIC POP UND MODE SO To select the sound modes, turn the SOUND MODE control until the sound mode you want appears on the display. When the sound mode is activated Pressing SOUND TURBO cancels the sound mode (set to OFF). Turning On or Off the Key-touch Tone SOUND MODE WOOFER SOUND MODE indicator also lights up on the display • As you turn the control, the sound modes change as follows: D.CLUB HALL STADIUM ROCK If you do not want the key-touch tone to beep each time you press a button or turn a control, you can deactivate it. • You can turn on or off the key-touch tone as follows: –When the unit is off: You can turn on or off the key-touch tone by operating the unit. –When the unit is on: You can turn on or off the key-touch tone by operating the unit or the remote control. (Dance CLUB) OFF (Canceled) CLASSIC POP Surround modes*: D.CLUB : Increases resonance and bass. HALL : Adds depth and brilliance to the sound. STADIUM: Adds clarity and spreads the sound, like in an outdoor stadium. On the unit: Press and hold BEEP for more than 2 seconds. SEA (Sound Effect Amplifier) modes: ROCK : Boosts low and high frequency. Good for acoustic music. POP : Good for vocal music. CLASSIC : Good for classical music. • Each time you press and hold the button, the key-touch tone turns on and off alternately. OFF Press BEEP ON/OFF when the unit is on. • Each time you press the button, the key-touch tone turns on and off alternately. : Cancels the sound mode. * Surround elements are added to the SEA elements to create being-there feeling in your room. When one of these modes is selected, the SOUND MODE indicator lights up as SOUND MODE . On the remote control: While one of the SEA modes (SEA elements without surround elements) is selected, the SOUND MODE indicator lights up as SOUND MODE . • The corresponding sound mode lamp also flashes. D A N C E When the sound mode is set to OFF All sound mode indicators do not flash but light up. 11 11_12MXGT88&GA77[B].pm6 11 03.2.8, 9:02 PM BEEP Listening to the Radio On the unit ONLY: Tuning in to a Station—Auto Search 1 Tune in to the station you want to preset (in 1 Press FM/AM. this example, of FM 87.50). The unit automatically turns on and tunes in to the previously tuned station (either FM or AM—MW). • Each time you press the button, the band alternates between FM and AM (MW). • See “Tuning in to a Station—Auto Search.” 2 Press SET. SET 2 Start searching for stations. On the unit: Press and hold TUNING + or TUNING – for more than 1 second. On the remote control: Press and hold 4/1 or ¢/¡ for more than 1 second. TUNING TUNING The unit starts searching for stations and stops when a station of sufficient signal strength is tuned in to. If a program is broadcast in stereo, the ST (stereo) indicator lights up. To stop during searching, press TUNING + or TUNING – (or 4/1 or ¢/¡ on the remote control). When you press TUNING + or TUNING – (or 4/1 or ¢/¡ on the remote control) briefly and repeatedly The frequency changes step by step. 3 Turn the PRESET +/– control to select a preset number. 4 Press SET again. PRESET SET The tuned station in step 1 is stored in the preset number selected in step 3. • Storing a new station on a used number erases the previously stored one. When you unplug the AC power cord or if a power failure occurs The preset stations will be erased in a few days. If this happens, preset the stations again. To change the FM reception mode When an FM stereo broadcast is hard to receive or noisy, press FM MODE on the remote control MP3 so that “MONO” appears and the MONO indicator also lights up on the display. Reception improves. To restore the stereo effect, press FM MODE again so that “STEREO” appears on the display. In this stereo mode, you can hear stereo sounds when a program is broadcast in stereo. Presetting Stations You can preset 30 FM and 15 AM (MW) stations. In some cases, test frequencies have been already memorized for the tuner since the factory examined the tuner preset function before shipment. This is not a malfunction. You can preset the stations you want into memory by following the presetting method. • There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again. Tuning in to a Preset Station 1 Press FM/AM. • See “Tuning in to a Station—Auto Search,” step 1 for details. 2 Select a preset number. PRESET On the unit: Turn the PRESET +/– control. On the remote control: Press the number buttons. Ex.: For preset number 5, press 5. For preset number 15, press +10 then 5. For preset number 20, press +10, then 10. For preset number 25, press +10, +10, then 5. For preset number 30, press +10, +10, then 10. 12 11_12MXGT88&GA77[B].pm6 12 03.2.8, 9:02 PM Receiving FM Stations with RDS RDS (Radio Data System) allows FM stations to send an additional signal along with their regular program signals. For example, the stations send their station names, as well as information about what type of program they broadcast, such as sports or music, etc. When tuned to an FM station which provides the RDS service, the RDS indicator lights up on the display. With the unit, you can receive the following types of RDS signals. PS (Program Service): Shows commonly known station names. RT (Radio Text): Shows text messages the station sends. 2 Press SELECT + or SELECT – Enhanced Other Networks: Provides the information about the types of the programs sent by other RDS stations. More about RDS • Some FM stations do not provide RDS signals. • RDS services may vary among FM RDS stations. For details on RDS services in your area, check with local radio stations. • RDS may not work correctly if the received station is not transmitting the signals properly or if the signal strength is weak. Changing the RDS Information You can see RDS information on the display while listening to an FM station. PS NAME RT CT (Radio Text) (Clock Time) To search for a program using PTY codes • PTY Search is applicable only to preset FM RDS stations. If not yet done, see “Presetting Stations” on page 12. • There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again. (or preset channel no.) About characters shown on the display When the display shows PS name, RT or CT signals: • The display cannot differentiate upper case and lower case letters and always uses upper case letters. • Some special characters and marks may not be displayed correctly. If no PS name, RT, or CT signals are sent by a station “NO PS,” “NO RT,” or “NO CT” appears on the display. until the PTY code you want appears on the display. • Each time you press the button, PTY codes change as follows: NEWS “ AFFAIRS “ INFO “ SPORT “ EDUCATE “ DRAMA “ CULTURE “ SCIENCE “ VARIED “ POP M “ ROCK M “ M.O.R. M “ LIGHT M “ CLASSICS “ OTHER M “ WEATHER “ FINANCE “ CHILDREN “ SOCIAL “ RELIGION “ PHONE IN “ TRAVEL “ LEISURE “ JAZZ “ COUNTRY “ NATION M “ OLDIES “ FOLK M “ DOCUMENT “ (back to the beginning) 3 Press RDS MODE again while the RDS MODE PTY code selected in the previous step is still on the display. The preset FM stations appear on the display with their preset numbers. The unit searches 30 preset FM stations, stops when it finds the one you have selected and tunes in that station. • If no program is found, the unit returns to the last received station. To stop during searching Press SELECT + or SELECT –. To check the PTY, press RDS MODE once so that the current PTY code appears. • “NO PTY” appears if no signal is sent. 13 13 SELECT DISPLAY MODE Station frequency 13_14MXGT88&GA77[B].pm6 RDS MODE an FM station. PTY (Program Type): Shows types of broadcast programs. (Program Service name) One of the advantages of RDS is that you can locate a particular kind of program by specifying PTY codes. • For details on the PTY codes, see “Additional Information” on page 30. 1 Press RDS MODE while listening to CT (Clock Time): Shows clock time the station sends. Press DISPLAY MODE. • Each time you press the button, the display changes as follows: Searching for Programs by PTY Codes (PTY Search) 03.2.8, 9:02 PM Switching Temporarily to a Program Type of Your Choice How the Enhanced Other Networks function actually works: The Enhanced Other Networks function allows the unit to switch temporarily to a broadcast program of your choice (NEWS or INFO) from a different station. If there is no station broadcasting the program you have selected The unit continues tuning in to the current station. « When a station starts broadcasting the program you have selected, the unit automatically switches to the station. The selected data type indicator starts flashing on the display. « When the program is over, the unit goes back to the previously tuned station, but the Enhanced Other Networks function still remains activated. To activate the Enhanced Other Networks function Enhanced Other Networks function is applicable only to preset FM RDS stations. If not yet done, see “Presetting Stations” on page 12. • There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again. 1 Press and hold RDS MODE for RDS MODE more than 1 second. “E.SELECT” appears on the display. 2 Press SELECT + or SELECT – SELECT to select the data type. • Each time you press the button, the data type of the Enhanced Other Networks changes as follows: CASE 1 CASE 2 If there is a station broadcasting the program you have selected The unit tunes in to the program. The selected data type indicator starts flashing. « When the program is over, the unit goes back to the previously tuned station, but the Enhanced Other Networks function still remains activated. CASE 3 NEWS INFO E.OFF NEWS: News INFO: Program the purpose of which is to impart advice in the widest sense. E.OFF: The function is canceled. The data type indicator (NEWS or INFO) you have selected also lights up on the display. Now, the function is activated. See “How the Enhanced Other Networks function actually works.” To cancel the function, repeat from step 1 and select “E.OFF” in step 2. The data type indicator (NEWS or INFO) goes off. If the FM station you are listening to is broadcasting the program you have selected The unit continues to receive the station but the selected data type indicator starts flashing. « When the program is over, the indicator stops flashing, but the Enhanced Other Networks function still remains activated. More about the Enhanced Other Networks function • Enhanced Other Networks data sent from some stations may not be compatible with this unit. In this case, the Enhanced Other Networks function may not work correctly. • While listening to a program tuned in by this function, the station does not change even if another network station starts broadcasting a program of the same Enhanced Other Networks data. • If the stations alternate intermittently between the station tuned by this function and the currently tuned station, cancel this function by following the procedure in the left column. • The Enhanced Other Networks function is canceled when you change the source to CD, TAPE or AUX. • The Enhanced Other Networks function is temporarily canceled when you change the band to AM (MW). 14 13_14MXGT88&GA77[B].pm6 14 03.2.8, 9:02 PM Playing Back CDs This unit has been designed to playback the following CDs: • Audio CD • CD-R (CD-Recordable) • CD-RW (CD-ReWritable) • MP3 disc (MP3 files recorded on a CD-R or CD-RW)* When playing a CD-R or CD-RW • User-edited CD-Rs (CD-Recordable) and CD-RWs (CD-ReWritable) can be played back when they are already “finalized.” • Before playing back CD-Rs or CD-RWs, read their instructions or cautions carefully. • Some CD-Rs or CD-RWs may not be played back on this unit because of their disc characteristics, damage or stain on them, or if the player’s lens is dirty. Important notices: • In general, you will have the best performance by keeping your CDs and the mechanism clean. - Store CDs in their cases, and keep them in cabinets or on shelves. - Keep the unit’s carrousel closed when not in use. • Continuous use of irregular shaped discs (heart-shape, octagonal, etc.) can damage the disc rotating mechanism. Loading CDs 1 Press 0. The unit automatically turns on and the carrousel comes out. 2 Place one or two discs correctly on the front recesses of the disc tray, with its label side up. INCORRECT CORRECT • When using a CD single (8 cm), place it on the inner recess of the disc tray. DISC CHANGE 3 If you wish to load a third disc, press DISC CHANGE on the unit or DISC SKIP on the remote control. The disc tray rotates by 120˚. 4 Press 0 again. The carrousel closes. • CD-RWs may require a longer readout time since the reflectance of CD-RWs is lower than for regular CDs. *For MP3 discs • This unit manages files and folders on MP3 discs as “tracks” and “albums.” • Playback order of the MP3 files (tracks) recorded on a disc are determined by the writing (or encoding) application; therefore, playback order may be different from the one you have intended while recording the files and the folders. • This unit show the file name—Available characters: 0–9, A–Z, _ (underscore)—on the display when the file (tracks) starts play; however some file names are not shown correctly. • • • • • • More about MP3 discs MP3 discs (either CD-R or CD-RW) require a longer readout time. (It varies due to the complexity of the recording configuration.) When making an MP3 disc, select ISO 9660 Level 1 or Level 2 as the disc format. This unit does not support multisession recording. This unit can play MP3 files only with the following file extensions— “.MP3,” “.Mp3,” “.mP3,” and “.mp3.” Non-MP3 files are ignored. If non-MP3 files are recorded together with MP3 files, this unit will take a longer time to scan the disc. It may also cause the unit to malfunction. Some MP3 discs may not be played back because of their disc characteristics or recording conditions. Playing Back CDs—All Disc and One Disc You can play all loaded CDs continuously—All Disc play, or one selected disc—One Disc play. All Disc play On the unit ONLY: 1 Load CDs. • If the current playing source is not the CD player, press CD 6, then 7 before going to the next step. 2 Press REPEAT repeatedly so that REPEAT the ALL DISC indicator lights up on the display. For Audio CD: Total playing time TRACK ALL WOOFER Total Track number For MP3 disc: DISC ALL DISC indicator MP3 indicator GROUP MP3 ALL WOOFER DISC GROUP indicator appears when the MP3 playback mode is the ALBUM mode. See also page 19. 15 15_19MXGT88&GA77[B].pm6 15 03.2.8, 9:02 PM Continued • Each time you press the button, the indication on the display changes as follows: ALL DISC 1 DISC • When the MP3 playback mode is the TRACK mode (See also page 19.) Current track title scrolls. REPEAT 1* (initial setting) REPEAT ALL DISC* REPEAT 1 DISC* MP3 * See page 21. 3 Press one of the disc number WOOFER CD 1 buttons (CD1, CD2 or CD3) for the disc you want to start to play from. Current track number** CD play starts from the first track of the selected disc. • Pressing CD 6 instead of the disc number buttons starts playing back if a CD is on the tray. For Audio CD: Track number of the currently playing disc flashes (Track numbers exceeding 16 are not displayed.) TRACK ALL Current track number DISC ALL DISC DISC Elapsed playing time Elapsed playing time MP3 WOOFER WOOFER ALL CD 3 CD 2 ** In the TRACK mode, the unit manage only files (tracks) on the MP3 disc. Folders (albums) are not recognized. To stop during play, press 7. • For MP3 disc, this unit can store the number of the track that you have stopped playback. By pressing CD 6, you can start playback again from the beginning of the same track—Resume play (see also page 19). To remove the disc, press 0. For MP3 disc: • When the MP3 playback mode is the ALBUM mode (See also page 19.) Current album number GROUP MP3 ALL WOOFER DISC Current track title scrolls. GROUP MP3 WOOFER Current track number of the current album GROUP ALL DISC ALL DISC CD playback sequence When 3 CDs are loaded on the disc trays, they are played in one of the following sequences. • When CD1 is pressed : CD1 ] CD2 ] CD3 (then stops) • When CD2 is pressed : CD2 ] CD3 ] CD1 (then stops) • When CD3 is pressed : CD3 ] CD1 ] CD2 (then stops) * When only 2 CDs are loaded, they are played in the same order, but the disc tray without a CD is skipped. About the disc number lamps (CD1, CD2, and CD3) • Each disc number lamp corresponds to the disc tray of the same number. • The disc number lamp flashes while the corresponding CD is being played. • The disc number lamp goes off when the unit has detected that there is no CD on the corresponding disc tray. Elapsed playing time MP3 WOOFER 16 15_19MXGT88&GA77[B].pm6 16 03.2.8, 9:02 PM One Disc play Basic CD Operations When 2 or 3 CDs are loaded on the disc trays, you can select one particular disc to be played back. While playing a CD, you can do the following operations. On the unit ONLY: To exchange CDs during playback of another 1 Load CDs. • If the current playing source is not the CD player, press CD 6, then 7 before going to the next step. 2 Press REPEAT repeatedly so that REPEAT Press DISC CHANGE to change the CD and the carrousel comes out. If you change CDs during play, the current play will not stop until all CDs you have changed are played. DISC CHANGE To close the carrousel, press DISC CHANGE or 0. the 1 DISC indicator lights up on the display. 1 DISC indicator To skip to the another CD in the carrousel Press DISC SKIP on the remote control. TRACK 1 DISC WOOFER To stop play for a moment • Each time you press the button, the indication on the display changes as follows: ALL DISC 1 DISC REPEAT 1* (initial setting) REPEAT ALL DISC* Press CD 6. While pausing, “PAUSE” appears on the display. To resume play, press CD 6 again. REPEAT 1 DISC* * See page 21. 3 Press one of the disc number To locate a particular point in a track CD 1 CD 2 CD 3 buttons (CD1, CD2 or CD3) you want to listen. Playback stops when all tracks of the selected disc are played once and resumes to All Disc play. To stop during play, press 7. • For MP3 disc, this unit can store the number of the track that you have stopped playback. By pressing CD 6, you can start playback again from the beginning of the same track—Resume play (see also page 19). To remove the disc, press 0. To exit from One Disc play, press REPEAT repeatedly so that ALL DISC indicator lights up on the display. The following operations will also cancel the One Disc play and restore All Disc play when— • Turning off the power, • Ejecting the carrousel, or • Changing the source to play. During play, press and hold 1 or ¡. • 1: Fast reverses the disc. • ¡: Fast forwards the disc. When using the remote control, press and hold 4/1 or ¢/¡. To go to another track For Audio CD: Turn the 4/¢ control before or during playback. • 4: Goes back to the beginning of the current or previous tracks. • ¢: Skips to the beginning of the next or succeeding tracks. When using the remote control, press 4/1 or ¢/¡. If you turn the 4/¢ control (or press 4/1 or ¢/¡ on the remote control) to select a track while playback is stopped The selected track starts playback. 17 15_19MXGT88&GA77[B].pm6 17 03.2.8, 9:02 PM Continued For MP3 disc: When the MP3 playback mode is the TRACK mode (See also page 19.) Turn the 4/¢ control before or during playback. • 4: Goes back to the beginning of the current or previous tracks. • ¢: Skips to the beginning of the next or succeeding tracks. When using the remote control, press 4/1 or ¢/¡. If you turn the 4/¢ control (or press 4/1 or ¢/¡ on the remote control) to select a track while playback is stopped The selected track starts playback. To go to another track directly using the number buttons For Audio CD: Pressing the number button(s) before or during play allows you to start playing the selected track. Ex.: For track number 5, press 5. For track number 15, press +10, then 5. For track number 20, press +10, then 10. For track number 32, press +10, +10, +10, then 2. For MP3 disc: • When the MP3 playback mode is the TRACK mode (See also page 19.) Pressing the number button(s) before or during play allows you to start playing the selected track on the disc. To go to another album on an MP3 disc When the MP3 playback mode is the ALBUM mode (See also page 19.) Turn the 4/¢ control before or during playback. • 4: Goes back to the beginning of the first track in the previous albums. • ¢: Skips to the beginning of the first track in the next or succeeding albums. When using the remote control, press 4/1 or ¢/¡. If you turn the 4/¢ control (or press 4/1 or ¢/¡ on the remote control) to select an album while playback is stopped The first track in the selected album starts playback. Ex.: For track number 5, press 5. For track number 15, press +10, then 5. For track number 20, press +10, then 10. For track number 32, press +10, +10, +10, then 2. For track number 123, press +10 twelve times, then 3. • When the MP3 playback mode is the ALBUM mode (See also page 19.) Pressing the number button(s) before or during play allows you to start playing the selected track in the current album. Ex.: For track number 5, press 5. For track number 15, press +10, then 5. For track number 20, press +10, then 10. For track number 32, press +10, +10, +10, then 2. For track number 123, press +10 twelve times, then 3. If your entry is ignored You have tried to enter a track number that does not exist on the disc or in the album (for example, selecting track 14 in the album that only has 12 tracks). Such entries are ignored. 18 15_19MXGT88&GA77[B].pm6 18 03.2.8, 9:02 PM Changing the MP3 Playback Mode Turning On or Off the Resume Play for MP3 Disc When playing an MP3 disc, you can choose the playback mode of the MP3 disc as follows: For MP3 disc, this unit can store the number of the track that you have stopped playback. By pressing CD 6, you can start playback again from the beginning of the same track— Resume play. You can turn on and off the resume play for MP3 discs. • TRACK mode: The unit recognizes only tracks (files). You can play an MP3 disc like an Audio CD. • ALBUM mode: The unit recognizes tracks (files) and albums (folders) on an MP3 disc. You can play an MP3 disc according to the way how they are grouped. In this mode, you can do the following operations: • Turning the 4/¢ control (or pressing 4/1 or ¢/¡ on the remote control) allows you to skip to the first track of the previous or next albums. (See page 18.) • Pressing the number button(s) allows you to start playing the selected track in the current album. (See page 18.) Press PROGRAM before or during playing an MP3 disc. Press MP3 before or during playing an MP3 disc. MP3 ALL WOOFER MP3 ALL DISC GROUP indicator appears when the MP3 playback mode is the ALBUM mode. • Each time you press the button, the MP3 playback mode changes between “ALBUM” and “TRACK” alternately. 19 15_19MXGT88&GA77[B].pm6 19 DISC The following operations will erase the memory of the track number that you have stopped playback when— • Pressing 0 to eject the disc. • Pressing one of the disc number buttons to change the disc to play. MP3 WOOFER PROGRAM • Each time you press PROGRAM, the resume play turns on and off alternately. On the remote control ONLY: GROUP On the unit ONLY: 03.2.11, 10:01 PM Continued Programming the Playing Order of the Tracks —–Program Play 5 Program other tracks you want. You can arrange the order in which the tracks play before you start playing. You can program up to 32 tracks. • To use Repeat play (see page 21) for Program play, press REPEAT after starting Program play. • This function does not work for MP3 discs. 6 Press CD 6. On the unit ONLY: To stop during play, press 7. 1 Load CDs. • If the current playing source is not the CD player, press CD 6, then 7 before going to the next step. 2 Press PROGRAM so that PROGRAM “PROGRAM” appears on the display. TRACK PRGM ALL WOOFER DISC • If a program has been stored in memory, the program is called up. CD 1 CD 3 CD 2 number buttons (CD1, CD2, and CD3) to select the disc number you want to play. Disc number Program step number TRACK PRGM ALL WOOFER DISC 4 Turn the 4/¢ control to select the track number, then press SET. Each time you select a track and press SET, the selected track number is added to the track number indicator. • You can select up to the 99th track on each disc. CANCEL Before playing, you can erase the last / DEMO programmed track shown on the display by pressing CANCEL/DEMO. • Each time you press the button, the last programmed track is erased from the program. To check the program during play, perform the following procedure: • You can check only the programmed tracks on the current disc at one time. 1 Press CD 6 to pause Program play. 2 Turn the 4/¢ control. The programmed tracks on the currently selected disc appear on the display in the programmed (or reverse) order. • If tracks on another disc have been programmed, “PAUSE” appears on the display. To check the programmed tracks on another disc, press CD 6 twice, then turn the 4/¢ control. • Pressing CD 6 again starts Program play from the track currently shown on the display. To add tracks in the program before play, simply select the disc numbers and/or track numbers you want to add by following steps 3 and 4 of the programming procedure. If you try to program a 33rd track “FULL” will appear on the display. SET If you have programmed a track from an empty tray, or a track number that does not exist on the disc Such program steps will be skipped. PRGM ALL WOOFER To exit from Program play, press PROGRAM again before or after play so that the unit enters All Disc play. (The program you have made is stored in memory until you turn off the unit, eject the carrousel, or erase the program.) • Program play is also canceled when you press 0. To erase the entire program before or during play, press 7 twice. • Turning the power off or ejecting the carrousel will also erase the stored memory. Track number TRACK The tracks are played in the order you have programmed. To modify the program The PRGM (program) indicator also lights up on the display. • All Disc play is selected automatically. You cannot select One Disc play for Program play. 3 Press one of the disc • To program tracks from the same disc, repeat step 4. • To program tracks from a different disc, repeat steps 3 and 4. DISC If there is an MP3 disc on the disc tray Even if you add tracks on the MP3 disc to the program in step 3 to 5, those tracks will be skipped. 20 20_22MXGT88&GA77[B]B.pm6 20 03.2.28, 9:43 AM Playing at Random—–Random Play Repeating Tracks or CDs—–Repeat Play The tracks of the selected CD will play at random. • To use Random play, you have to cancel the Program play. You can have all the CDs, the program or the individual track currently playing repeat as many times as you like. • Repeat play and Random play cannot be used at the same time. On the unit ONLY: 1 Load a CD. 2 Press one of the disc number On the unit ONLY: CD 1 CD 2 CD 3 buttons (CD1, CD2, and CD3) for the disc you want to play, then press 7. To repeat play, press REPEAT during or before playing. • Each time you press the button, Repeat play mode changes as follows, and the following indicator lights up on the display: ALL DISC* 1 DISC* REPEAT ALL DISC 3 Press RANDOM so that RANDOM “RANDOM” appears on the display. The RANDOM indicator also lights up on the display. • Activating Random play cancels Repeat play or All Disc play. (One Disc play is automatically selected.) • For MP3 discs, activating Random play changes the ALBUM mode to the TRACK mode. REPEAT REPEAT 1 REPEAT 1 DISC REPEAT 1: Repeats one track on one CD. REPEAT 1 DISC**: Repeats all the tracks on one CD. REPEAT ALL DISC: Repeats all the tracks on all the CDs, or all the tracks on the program. * See pages 15 and 17. ** REPEAT 1 DISC is not used for Program play. To cancel Repeat play, press REPEAT repeatedly until the REPEAT indicator (REPEAT 1, REPEAT 1 DISC or REPEAT ALL DISC) goes off from the display. • Repeat play is also canceled when you press 7 or 0. Prohibiting Disc Ejection—–Carrousel Lock RANDOM 1 DISC WOOFER • The tracks are played automatically at random. Random play ends when all tracks are played once. To stop and cancel Random play, press 7. • If you press RANDOM again during play, Random play is canceld and the unit enters All Disc play mode. • Random play is also canceled when you press 0. If you turn the 4/¢ control (or press 4/1 or ¢/¡ on the remote control) Playback skips to the next track selected randomly. You can prohibit CD ejection from the unit and can lock the carrousel. • This operation is possible only while the unit is on with CD selected as the source. On the unit ONLY: To prohibit disc ejection, press 0 for the carrousel while holding 7. “LOCKED” appears for a while, and the carrousel is locked. If you try to eject CDs “LOCKED” appears to inform you that the Carrousel Lock is in use. To cancel the prohibition and unlock the carrousel, press 0 for the carrousel while holding 7. “UN LOCKED” appears for a while, and the carrousel is unlocked. When you unplug the AC power cord or if a power failure occurs The setting of the Carrousel Lock will return to the initial setting (not to prohibit disc ejection) in a few days. 21 20_22MXGT88&GA77[B].pm6 21 03.2.8, 9:03 PM Playing Back Tapes To stop during play, press 7. Playing Back a Tape 1 Press 0 EJECT for the deck you want to use. To operate the other deck, press TAPE A/B (or A/B on the remote control), then TAPE 3. To fast-forward the tape, press ¡ (or ¢/¡ on the remote control). The tape running indicator (3) starts flashing quickly. To rewind the tape, press 1 (or 4/1 on the remote control). The tape running indicator (2) starts flashing quickly. To remove the cassette, press 0 EJECT for deck A or EJECT 0 for deck B. For Deck B For Deck A 2 Put a cassette in, with the exposed part of the tape down and the side you want to play facing front. • You can play back only type I tapes. 3 Close the cassette holder gently. If you put cassettes in both decks A and B, the last deck which you have put a cassette into is selected. To operate the other deck, press TAPE A/B (or A/B on the remote control). 4 Press TAPE 3. The tape play starts and the tape running indicator (3) starts flashing slowly. The use of the C-120 or thinner tape is not recommended, since characteristic deterioration may occur and this tape easily jams in the pinchrollers and the capstans. When the tape plays to the end, the deck automatically stops. 22 20_22MXGT88&GA77[B].pm6 22 03.2.8, 9:03 PM Recording Recording a Tape on Deck B IMPORTANT: • It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable program and in any literary, dramatic, musical, or artistic embodied therein. • The recording level is automatically set correctly, so it is not affected by the VOLUME, the SUBWOOFER LEVEL, and the SOUND MODE controls. Thus, during recording you can adjust the sound you are actually listening to without affecting the recording level. • While recording, you can hear the SOUND TURBO effect through the speakers or headphones. However, the sound is recorded without this effect (see page 10). • If recordings you have made have excessive noise or static, the unit may be too close to a TV. Place the unit away from the TV. • You can use type I tape for recording. On the unit ONLY: 1 Press EJECT 0 for deck B. To protect your recording Cassettes have two small tabs on the back to protect unexpected erasure or re-recording. To protect your recording, remove these tabs. To re-record on a protected tape, cover the holes with adhesive tape. 2 Put a recordable cassette in, with the exposed part of the tape down and the side you want to record facing front. 3 Close the cassette holder gently. 4 Start playing the source—FM, AM, CD To keep the best recording and playback sound quality player or auxiliary equipment connected to AUX IN jacks. • For duplicating tapes, see “Dubbing Tapes” on page 24. • For recording from CD, see “CD Synchronized Recording” on page 24. If the heads, capstans, and pinch rollers of the cassette decks become dirty, the following will occur: • Impaired sound quality • Discontinuous sound • Fading • Incomplete erasure • Difficulty in recording 5 Press REC START/STOP. To clean the head, capstan, and pinch roller Use a cotton swab moistened with alcohol. To stop during recording, press REC START/STOP again or 7. To remove the cassette, press EJECT 0 for deck B. Capstan Erase head Pinch roller Head To demagnetize the head Turn off the unit, and use a head demagnetizer (available at electronics and audio shops). 23 23_32MXGT88&GA77[B].pm6 23 REC START / STOP The REC (recording) indicator lights up on the display and recording starts. 03.2.8, 9:03 PM Dubbing Tapes CD Synchronized Recording You can easily record a CD onto a tape. • This function does not work for MP3 discs. When recording an MP3 disc onto a tape, see “Recording a Tape on Deck B” on page 23. • You can also record the tracks in the order you have made the program. If there is a track on the MP3 disc in the program, it will be skipped and some blank space will be recorded on the tape. On the unit ONLY: 1 Press TAPE 3, then 7. On the unit ONLY: 2 Put the source cassette in deck A, and a recordable cassette into deck B. 3 Press DUBBING. DUBBING Dubbing starts. “DUBBING” appears, and the REC (recording) indicator lights up on the display. 1 Put a recordable cassette into deck B. 2 Place a disc correctly on the recess of the disc tray, with its label side up. 3 Press one of the disc CD 1 CD 2 CD 3 number buttons (CD1, CD2, and CD3) to select the disc, then 7. WOOFER 4 Press CD REC START. CD REC START “CD REC” appears, and the REC (recording) indicator lights up on the display. TRACK WOOFER 1 DISC WOOFER To stop during dubbing, press REC START/STOP or 7. To remove the cassettes, press 0 EJECT for deck A and EJECT 0 for deck B. Deck B starts recording and the CD player starts playing. When the recording from the selected CD is done, the CD player and deck B stop. • When recording your program, the CD player and deck B stop after all tracks in the program are recorded. To stop during CD Synchronized Recording, press REC START/STOP or 7. To remove the cassette, press EJECT 0 for deck B. 24 23_32MXGT88&GA77[B].pm6 24 03.2.8, 9:03 PM Using the Timers There are three timers available—Daily Timer, Recording Timer, and Sleep Timer. Before using the timers, you need to set the clock built in the unit. (See “Setting the Clock” on page 9.) On the unit ONLY: 1 Press CLOCK/TIMER CLOCK / TIMER repeatedly until “DAILY” appears on the display. indicator lights up and the DAILY (daily timer) indicator starts flashing on the display. Using Daily Timer With Daily Timer, you can wake to your favorite music or radio program. You can set the timer whether the unit is on or off. WOOFER How Daily Timer actually works The unit automatically turns on, set the volume level to the preset level, and starts playing the specified source when the on-time comes (the indicator flashes while the timer is operating). Then, when the off-time comes, the unit automatically turns off (stands by). Daily Timer works every day unless you cancel it. • There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again. • If you have made a mistake while setting timer, press CANCEL/DEMO. (However, this does not always work. If CANCEL/DEMO does not work, press CLOCK/TIMER repeatedly and start from step 1 again.) Before you start... • When using a CD as the source to play: —Make sure there is a CD on the currently selected disc number tray. • When using a tape as the source to play: —Make sure that a tape is in the deck whose deck indicator (A or B) is lit on the display. • When using the external component as the source to play: —Set the timer equipped with the external component at the same time. • Each time you press the button, the clock/timer setting modes change as follows: ON TIME DAILY REC (Daily Timer) CLOCK ON TIME (See page 9.) (Recording Timer) Canceled 2 Press CLOCK/TIMER again. CLOCK / TIMER “ON TIME” appears for 2 seconds, then the unit enters on-time setting mode. WOOFER 3 Set the on-time you want the unit to turn on. 1) Turn the 4/¢ control to set the hour, then press SET. 2) Turn the 4/¢ control to set the minute, then press SET. “OFF TIME” appears for 2 seconds, then the unit enters off-time setting mode. SET 4 Set the off-time you want the unit to turn off (on standby). 1) Turn the 4/¢ control to set the hour, then press SET. 2) Turn the 4/¢ control to set the minute, then press SET. The unit enters source selecting mode. WOOFER 25 23_32MXGT88&GA77[B].pm6 25 03.2.8, 9:03 PM SET Continued 5 Turn the 4/¢ control to select To turn on or off Daily Timer after its setting is done the source to play, then press SET. 1 Press CLOCK/TIMER repeatedly until “DAILY” appears on the display. • Each time you turn the 4/¢ control, the source changes as follows: TUNER AM TUNER FM AUX TAPE SET CD TUNER FM : tunes in to a specified preset FM station. = go to step 6. TUNER AM : tunes in to a specified preset AM station. = go to step 6. CD : plays the current disc from the first track. = go to step 7. TAPE : plays a tape in deck A or B. = go to step 7. AUX : plays an external source. = go to step 7. 2 To turn off the Daily Timer, press CANCEL/DEMO. The DAILY (daily timer) indicator goes off from the display (“OFF” appears for a while). The Daily Timer is canceled, but the setting for the Daily Timer remains in memory until you change it. To turn on the Daily Timer, press SET. The DAILY (daily timer) indicator lights up on the display. The settings you have done are shown on the display in sequence for your confirmation. CLOCK / TIMER CANCEL / DEMO SET 6 Select the preset station number. Turn the 4/¢ control to select the preset station number, then press SET. The unit enters volume setting mode. SET 7 Turn the 4/¢ control to set the volume level. • You can select the volume level from VOL MIN, VOL 1 — VOL 30, and VOL MAX. WOOFER 8 Press SET to complete the Daily SET Timer setting. The DAILY (daily timer) indicator stops flashing and remains lit. The settings you have done are shown on the display in sequence for your confirmation. 9 Press to turn off the unit (on standby) if you have set the Daily Timer with the unit turned on. STANDBY ECO If the unit is turned on when the timer-on time comes Daily Timer does not work. 26 23_32MXGT88&GA77[B].pm6 26 03.2.8, 9:03 PM 3 Press CLOCK/TIMER again. Using Recording Timer With Recording Timer, you can make a tape of a radio broadcast automatically. You can set the timer whether the unit is on or off. How Recording Timer actually works WOOFER The unit automatically turns on, tunes in to the specified station, sets the volume level to “VOL MIN,” and starts recording when the on-time comes (the indicator flashes while the timer is operating). Then, when the off-time comes, the unit automatically turns off (stands by). Recording Timer works only once, but the timer setting remains in memory until you change it. • There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again. • If you have made a mistake while setting the timer, press CANCEL/DEMO. (However, this does not always work. If CANCEL/DEMO does not work, press CLOCK/TIMER repeatedly and start from step 2 again.) On the unit ONLY: 1 Put a recordable cassette into deck B. 2 Press CLOCK/TIMER CLOCK / TIMER repeatedly until “REC” appears on the display. indicator lights up and the REC (recording timer) indicator starts flashing on the display. WOOFER • Each time you press the button, the clock/timer setting modes change as follows: ON TIME DAILY REC (Daily Timer) Canceled “ON TIME” appears for 2 seconds, then the unit enters on-time setting mode. CLOCK / TIMER CLOCK ON TIME (See page 9.) (Recording Timer) 4 Set the on-time you want the unit to turn on. 1) Turn the 4/¢ control to set the hour, then press SET. 2) Turn the 4/¢ control to set the minute, then press SET. “OFF TIME” appears for 2 seconds, then the unit enters off-time setting mode. SET 5 Set the off-time you want the unit to turn off (on standby). 1) Turn the 4/¢ control to set the hour, then press SET. 2) Turn the 4/¢ control to set the minute, then press SET. The unit enters preset station selecting mode. SET 6 Select the preset station. 1) Turn the 4/¢ control to select the band (“TUNER FM” or “TUNER AM”), then press SET. 2) Turn the 4/¢ control to select a preset channel number, then press SET. The REC (recording timer) indicator stops flashing and remains lit. The settings you have done are shown on the display in sequence for your confirmation. 7 Press to turn off the unit (on standby) if necessary. SET STANDBY ECO About the recording source If you change the source while recording, the recording source also changes. 27 23_32MXGT88&GA77[B].pm6 27 03.2.8, 9:03 PM To turn on or off Recording Timer after its setting is done Timer Priority 1 Press CLOCK/TIMER repeatedly until “REC” appears on the display. Since each timer can be set separately, you may wonder what happens if the setting for these timers overlaps. Here are some examples. CLOCK / TIMER 2 To turn off the Recording Timer, CANCEL / DEMO press CANCEL/DEMO. The REC (recording timer) indicator goes off from the display (“OFF” appears for a while). The Recording Timer is canceled, but the setting for the Recording Timer remains in memory until you change it. To turn on the Recording Timer, SET press SET. The REC (recording timer) indicator lights up on the display. The settings you have done are shown on the display in sequence for your confirmation. • Recording Timer has priority over Daily Timer. If Recording Timer is set to come on while Daily Timer is operating, Daily Timer is canceled and Recording Timer start working. AM 6:00 7:00 7:30 Recording Timer Daily Timer canceled. • If Sleep Timer overlaps with another timer (either Daily Timer or Recording Timer), a timer with the earlier shut-off time has priority. Using Sleep Timer AM 6:00 With Sleep Timer, you can fall asleep to music. You can set Sleep Timer when the unit is turned on. 6:30 6:30 7:00 7:30 Sleep Timer Recording Timer canceled. How Sleep Timer actually works The unit automatically turns off after the specified time length passes. When using the Recording Timer and Sleep Timer at the same time, pay special attention to the shut-off time. On the remote control ONLY: 1 Press SLEEP. The time length until the shut-off time appears and the SLEEP indicator starts flashing on the display. • Each time you press the button, the time length changes as follows: SLEEP10 OFF SLEEP20 SLEEP30 SLEEP120 SLEEP60 SLEEP90 (Canceled) 2 Wait for about 3 seconds after specifying the time length. The SLEEP indicator stops flashing and remains lit. To check the remaining time until the shut-off time, press SLEEP once so that the remaining time until the shut-off time appears for about 3 seconds. To change the shut-off time, press SLEEP repeatedly until the desired time length appears on the display. To cancel the setting, press SLEEP repeatedly until “OFF” appears on the display so that the SLEEP indicator goes off from the display. • Sleep Timer is also canceled when you turn off the unit. 28 23_32MXGT88&GA77[B].pm6 28 03.2.8, 9:03 PM Maintenance To get the best performance of the unit, keep your discs, tapes, and mechanism clean. Handling cassette tapes Cleaning the unit • Stains on the unit Should be wiped off with a soft cloth. If the unit is heavily stained, wipe it with a cloth soaked in water-diluted neutral detergent and wrung well, then wipe clean with a dry cloth. • Avoid the following since they may cause damage to the unit. - DO NOT wipe it with a hard cloth. - DO NOT wipe it strong. - DO NOT wipe it with thinner or benzine. - DO NOT apply any volatile substance such as insecticides to it. - DO NOT allow any rubber or plastic to remain in contact with it for a long time. Handling discs • Remove the disc from its case by holding it at the edge while pressing the center hole lightly. • Do not touch the shiny surface of the disc, or bend the disc. • Put the disc back in its case after use to prevent warping. • If the tape is loose in its cassette, take up the slack by inserting a pencil in one of the reels and rotating. • If the tape is loose, it may get stretched, cut, or caught in the cassette. • Be careful not to touch the tape surface. • Avoid the following places to store the tape: — In dusty places — In direct sunlight or heat — In moist areas — Near a magnet • Be careful not to scratch the surface of the disc when placing it back in its case. • Avoid exposure to direct sunlight, temperature extremes, and moisture. To clean the disc Wipe the disc with a soft cloth in a straight line from center to edge. DO NOT use any solvent—such as conventional record cleaner, spray, thinner, or benzine—to clean the disc. 29 23_32MXGT88&GA77[B].pm6 29 03.2.8, 9:03 PM Additional Information Description of the PTY codes: NEWS: News. WEATHER: Weather reports and forecasts. AFFAIRS: Topical program expanding or enlarging upon the news — debate, or analysis. FINANCE: Stock Market reports, commerce, trading etc. INFO: Program the purpose of which is to impart advice in the widest sense. SPORT: Program concerned with any aspect of sports. CHILDREN: Programs targeted at a young audience. SOCIAL: Programs about sociology, history, geography, psychology and society. RELIGION: Religious programs. PHONE IN: CULTURE: Programs concerning any aspect of national or regional culture, including language, theatre, etc. Involving members of the public expressing their views either by phone or at a public forum. TRAVEL: Travel information. LEISURE: Programs about recreational activities. SCIENCE: Programs about natural sciences and technology. JAZZ: Jazz music. COUNTRY: Songs which originate from, or continue the musical tradition of the American Southern States. NATION M: Current popular music of the nation or region in that country’s language. OLDIES: Music from the so-called “golden age” of popular music. FOLK M: Music which has its roots in the musical culture of a particular nation. EDUCATE: Educational programs. DRAMA: All radio plays and serials. VARIED: Used for mainly speech-based programs like quizzes, panel games and personality interviews. POP M: Commercial music of current popular appeal. ROCK M: Rock music. M.O.R. M: Current contemporary music considered to be “easy-listening.” LIGHT M: Instrumental music, and vocal or choral works. CLASSICS: Performances of major orchestral works, symphonies, chamber music, etc. DOCUMENT: Program concerning factual matters, presented in an investigative style. OTHER M: Music not fitting into any of the other categories. Classification of the PTY codes for some FM stations may be different from the above list. 30 23_32MXGT88&GA77[B].pm6 30 03.2.8, 9:03 PM Troubleshooting If you are having a problem with your unit, check this list for a possible solution before calling for service. If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person, such as your dealer, for service. Symptom Cause Action Unable to cancel the display demonstration. Other buttons are pressed to cancel the display demonstration. Press CANCEL/DEMO on the unit. (See page 8.) No sound is heard. Connections are incorrect or loose. Check all connections and make corrections. (See pages 6 to 8.) Hard to listen to broadcasts because of noise. • Antennas are disconnected. • The AM (MW) loop antenna is too close to the unit. • The FM antenna is not properly extended and positioned. • Reconnect the antennas correctly and securely. • Change the position and direction of the AM (MW) loop antenna. • Extend the FM antenna at the best position. The disc sound is discontinuous. The disc is scratched or dirty. Clean or replace the disc. (See page 29.) The carrousel does not open or close. • The AC power cord is not plugged in. • The carrousel is locked. • Plug the AC power cord. • Unlock the carrousel. (See page 21.) The disc does not play. The disc is placed upside down. Place the disc with the label side up. The MP3 disc does not play. • No MP3 files are recorded on the disc. • MP3 files do not have the file extension—.MP3, .Mp3, .mP3, or .mp3 in their file names. • MP3 files are not recorded in the format compliant with ISO 9660 Level 1 or Level 2. Replace the disc. The readout time of the MP3 disc is too long. The readout time varies with the complexity of the recording configuration. Do not use too many hierarchies and folders when recording. Also, do not record any other types of audio tracks together with MP3 files. (See page 15.) The cassette holders cannot be opened. Power supply from the AC power cord has been cut off while the tape was running. Turn on the unit. Impossible to record. Small tabs on the back of the cassette are removed. Cover the holes with adhesive tape. Operations are disabled. The built-in microprocessor may malfunction due to external electrical interference. Unplug the AC power cord and then plug it back in. Unable to operate the unit from the remote control. • The path between the remote control and the remote sensor on the unit is blocked. • The batteries are exhausted. • Remove the obstruction. • Replace the batteries. 31 23_32MXGT88&GA77[B].pm6 31 03.2.8, 9:03 PM Specifications Design and specifications are subject to change without notice. CA-MXGT88 CA-MXGA77 Amplifier section Amplifier section Output Power SUBWOOFERS : 100 W per channel, min. RMS, driven into 6 Ω at 63 Hz with no more than 10% total harmonic distortion. (IEC268-3) 75 W per channel, min. RMS, driven into 6 Ω at 63 Hz with no more than 0.9% total harmonic distortion. (DIN) 55 W per channel, min. RMS, driven into 4 Ω at 1 kHz with no more than 10% total harmonic distortion. (IEC268-3) 35 W per channel, min. RMS, driven into 4 Ω at 1 kHz with no more than 0.9% total harmonic distortion. (DIN) MAIN SPEAKERS : Audio input sensitivity/Impedance (at 1 kHz, measured at MAIN SPEAKERS) AUX : 400 mV/50 kΩ Subwoofers : 6 Ω – 16 Ω Main speakers : 4 Ω – 8 Ω Speakers/Impedance : Tuner Output Power SUBWOOFERS : MAIN SPEAKERS : 80 W per channel, min. RMS, driven into 6 Ω at 63 Hz with no more than 10% total harmonic distortion. (IEC268-3) 65 W per channel, min. RMS, driven into 6 Ω at 63 Hz with no more than 0.9% total harmonic distortion. (DIN) 45 W per channel, min. RMS, driven into 4 Ω at 1 kHz with no more than 10% total harmonic distortion. (IEC268-3) 30 W per channel, min. RMS, driven into 4 Ω at 1 kHz with no more than 0.9% total harmonic distortion. (DIN) Audio input sensitivity/Impedance (at 1 kHz, measured at MAIN SPEAKERS) AUX : 400 mV/50 kΩ Speakers/Impedance : Subwoofers : 6 Ω – 16 Ω Main speakers : 4 Ω – 8 Ω Tuner FM tuning range : AM (MW) tuning range : 87.50 MHz – 108.00 MHz 522 kHz – 1 629 kHz CD player FM tuning range : AM (MW) tuning range : 87.50 MHz – 108.00 MHz 522 kHz – 1 629 kHz CD player CD Capacity : Dynamic range : Signal-to-noise ratio : 3 CDs 85 dB 85 dB Cassette deck CD Capacity : Dynamic range : Signal-to-noise ratio : 3 CDs 85 dB 85 dB Cassette deck Frequency response Normal (type I): Wow and flutter : 50 Hz — 14 000 Hz 0.15% (WRMS) General Frequency response Normal (type I): Wow and flutter : 50 Hz — 14 000 Hz 0.15% (WRMS) General Power requirement : Power consumption : AC 230 V , 50 Hz 160 W (at operation) 18 W (on standby; with power saving off—Normal Mode) 2.3 W (on standby; with power saving on—Eco mode) 270 mm x 317 mm x 453 mm (W/H/D) 9.3 kg Dimensions (approx.): Mass (approx.) : Power requirement : Power consumption : Dimensions (approx.): Mass (approx.) : Supplied accessories Supplied accessories See page 6. See page 6. AC 230 V , 50 Hz 150 W (at operation) 17 W (on standby; with power saving off—Normal Mode) 2.3 W (on standby; with power saving on—Eco mode) 270 mm x 317 mm x 453 mm (W/H/D) 9 kg 32 23_32MXGT88&GA77[B].pm6 32 03.2.8, 9:03 PM VICTOR COMPANY OF JAPAN, LIMITED EN V J Cover_MXGT88&GA77[B].pm6 2 03.2.8, 9:00 PM C 0203TMMMDWSAM
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Fill forms, Extract, Assemble, Print high-res Create Date : 2003:02:08 21:04:06 Producer : Acrobat Distiller 4.0 for Macintosh Modify Date : 2003:02:28 10:41:16+09:00 Title : CA-MXGT88/MXGA77[B] Author : JVC Subject : revisionB Page Count : 36 Page Mode : UseThumbs Page Layout : TwoColumnRightEXIF Metadata provided by EXIF.tools