JVC DR M10SEK M10EK_B User Manual LPT0901 001B

User Manual: JVC DR-M10SEK DR-M10SEK nglish,

Open the PDF directly: View PDF PDF.
Page Count: 116 [warning: Documents this large are best viewed by clicking the View PDF Link!]

1
STANDBY/ON
S-VIDEO VIDEO
L(MONO)
-
AUDIO
-
R
DV
DV IN
F1
REC MODE
PULL - OPEN
CABLE/DBS
DVDTV
DVD
CH
TIMER
REC LINK
PROG/CHECK
VCR Plus+
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
TV/CBL/DBS
STANDBY/ON
TV
MUTING
TV/
VIDEO
TV VOLUME
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DBS
DEF
SAT#
EN
Filename [DR-M10EK_02Cov1.fm]
DVD VIDEO RECORDER
INSTRUCTIONS
LPT0901-001B
DR-M10
DR-M10EK_02Cov1.fm Page 1 Tuesday, March 16, 2004 1:53 PM
Filename [DR-M10EK_03Safety.fm]
Masterpage:Left0
2
Page 2 February 25, 2004 5:57 pm
SAFETY FIRST
Safety Precautions
The rating plate and the safety caution are on the rear of
the unit.
WARNING: DANGEROUS VOLTAGE INSIDE
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
CLASS 1 LASER PRODUCT
REPRODUCTION OF LABELS
WARNING LABEL INSIDE OF THE UNIT
●Manufactured under licence from Dolby Laboratories. “Dolby” and double-D symbol are trademarks of Dolby Laboratories.
●“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
●VIDEO Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The VIDEO Plus+ system is
manufactured under license from Gemstar Development Corporation.
●This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is intended for home and other limited viewing users only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
CAUTION
A UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER
THIS UNIT USES A VISIBLE LASER BEAM WHICH
COULD CAUSE HAZARDOUS RADIATION
EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE
UNIT CORRECTLY AS INSTRUCTED.
WHEN THIS UNIT IS PLUGGED INTO THE WALL
OUTLET, DO NOT PLACE YOUR EYES CLOSE TO
THE OPENING OF THE DISC TRAY AND OTHER
OPENINGS TO LOOK INTO THE INSIDE OF THIS
UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
CAUTION
8When you are not using the unit for a long period
of time, it is recommended that you disconnect the
power cord from the mains outlet.
8Dangerous voltage inside. Refer internal servicing
to qualified service personnel. To prevent electric
shock or fire hazard, remove the power cord from
the mains outlet prior to connecting or
disconnecting any signal lead or aerial.
IMP
O
RTANT:
8Please read the various precautions on pages 2 – 4
before installing or operating the unit.
8It should be noted that it may be unlawful to
re-record pre-recorded tapes, DVDs, or discs
without the consent of the owner of copyright in
the sound or video recording, broadcast or cable
programme and in any literary, dramatic, musical,
or artistic work embodied therein.
DR-M10EK_01.book Page 2 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
3
Filename [DR-M10EK_03Safety.fm]
Page 3 February 25, 2004 5:57 pm
When the equipment is installed in a cabinet or a shelf,
make sure that it has sufficient space on all sides to allow
for ventilation (10 cm or more on both sides, on top and
at the rear).
When discarding batteries, environmental problems must
be considered and the local rules or laws governing the
disposal of these batteries must be followed strictly.
Failure to heed the following precautions may result in
damage to the unit, remote control or disc.
1. DO NOT place the unit —
— in an environment prone to extreme temperatures
or humidity.
— in direct sunlight.
— in a dusty environment.
— in an environment where strong magnetic fields are
generated.
— on a surface that is unstable or subject to vibration.
2. DO NOT block the unit’s ventilation openings or
holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to
get out.)
3. DO NOT place heavy objects on the unit or remote
control.
4. DO NOT place anything which might spill on top of
the unit or remote control.
(If water or liquid is allowed to enter this equipment,
fire or electric shock may be caused.)
5. DO NOT expose the apparatus to dripping or
splashing.
6. DO NOT use this equipment in a bathroom or places
with water. Also DO NOT place any containers filled
with water or liquids (such as cosmetics or medicines,
flower vases, potted plants, cups, etc.) on top of this
unit.
7. DO NOT place any naked flame sources, such as
lighted candles, on the apparatus.
8. AVOID violent shocks to the unit during transport.
MOISTURE CONDENSATION
Moisture in the air will condense on the unit when you
move it from a cold place to a warm place, or under
extremely humid conditions—just as water droplets form
on the surface of a glass filled with cold liquid. In
conditions where condensation may occur, disconnect
the unit’s power plug from the wall and keep it
disconnected for a few hours to let the moisture dry, then
turn on the unit.
The STANDBY/ON 1 button does not completely
shut off mains power from the unit, but switches
operating current on and off. “`” shows electrical
power standby and “!” shows ON.
A
TTENTION:
To mobile phone users:
Using a mobile phone in the vicinity of the unit may
cause picture vibration on the TV screen or change
the screen to a blue back display.
On placing the unit:
Some TVs or other appliances generate strong
magnetic fields. Do not place such appliances on top
of the unit as it may cause picture disturbance.
IMPORTANT
Connection to the mains supply in the United
Kingdom.
DO NOT cut off the mains plug from this equipment.
If the plug fitted is not suitable for the power points in
your home or the cable is too short to reach a power
point, then obtain a proper safety approved extension
lead/adapter or consult your dealer.
In the unlikely event of the plug fuse failing be sure to
replace the fuse only with an identical approved type,
as originally fitted, and to replace the fuse cover. If
the fuse fails again consult your nearest JVC dealer.
If nonetheless the mains plug is cut off remove the fuse
and dispose of the plug immediately, to avoid a
possible shock hazard by inadvertent connection to
the mains supply.
If this product is not supplied fitted with a mains
plug then follow the instructions given below:
DO NOT make any connection to the Larger Terminal
coded E or Green.
The wires in the mains lead are coloured in
accordance with the following code:
If these colours do not correspond with the terminal
identifications of your plug, connect as follows:
Blue wire to terminal coded N (Neutral) or coloured
Black.
Brown wire to terminal coded L (Live) or coloured
Red.
If in doubt — consult a competent electrician.
Blue to N (Neutral) or Black
Brown to L (Live) or Red
DR-M10EK_01.book Page 3 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_03Safety.fm]
Masterpage:Left+
4
Page 4 February 25, 2004 5:57 pm
SAFETY FIRST (cont.)
Some Do’s And Don’ts On The Safe Use
Of Equipment
This equipment has been designed and manufactured to meet international safety standards but, like any
electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.
DO read the operating instructions before you attempt to use the equipment.
DO ensure that all electrical connections (including the mains plug, extension leads and interconnections
between pieces of equipment) are properly made and in accordance with the manufacturer’s
instructions. Switch off and withdraw the mains plug when making or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your
equipment.
DO be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is
damaged in any way — switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed
for unattended operation or has a standby mode. Switch off using the switch on the equipment and
make sure that your family knows how to do this. Special arrangements may need to be made for
infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements
of road safety. It is illegal to watch television whilst driving.
DON’T listen to headphones at high volume, as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit
the manufacturer’s approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL...
—NEVER let anyone especially children push anything into holes, slots or any other opening in the
case — this could result in a fatal electrical shock;
—NEVER guess or take chances with electrical equipment of any kind — it is better to be safe than
sorry!
DR-M10EK_01.book Page 4 Friday, February 27, 2004 10:07 AM
Masterpage:Right
5
Filename [DR-M10EK_01TOC.fm]
Page 5 February 27, 2004 2:30 pm
CONTENTS
SAFETY FIRST 2
Safety Precautions ............................................... 2
Some Do’s And Don’ts On The Safe Use Of
Equipment ........................................................ 4
DISC INFORMATION 6
About Discs ......................................................... 6
INDEX 11
INSTALLING YOUR NEW UNIT 17
Check Contents ................................................. 17
Basic Connections ............................................. 18
S-VIDEO Connection ........................................ 19
Component Video Connection .......................... 20
INITIAL SETTINGS 21
Auto Set Up ....................................................... 21
Preset Download ............................................... 23
Monitor Set ....................................................... 25
Language ........................................................... 26
SAT CONTROL SET 28
Satellite Receiver Control Setting ....................... 28
T-V LINK 30
T-V Link Functions ............................................ 30
PLAYBACK OPERATIONS 31
Basic Playback .................................................. 31
Playback Features .............................................. 32
Live Memory Playback ...................................... 37
Using Play Set Up Menu ................................... 42
Parental Lock .................................................... 49
RECORDING 53
Basic Recording ................................................ 53
Recording Features ............................................ 54
TIMER RECORDING 56
VIDEO Plus+® Timer Programming ................... 56
Manual Timer Programming .............................. 58
On-Disc Timer Programming ............................ 60
Automatic Satellite Programme Recording ......... 65
NAVIGATION 66
Library Database DVD Navi .............................. 66
Modify Original Information .............................. 69
Modify Play List Information .............................. 72
Modify Library Information ................................ 76
Playback with MP3/JPEG Navigation ................. 78
EDITING 80
DV Dubbing ...................................................... 80
Edit From A Camcorder ..................................... 82
Edit To Or From Another Recorder .................... 83
Output/Input Set ................................................ 84
Digital Audio Dubbing ...................................... 86
REMOTE CONTROL 87
Remote Control Functions ................................. 87
SYSTEM CONNECTIONS 90
Connecting To A Satellite Receiver .................... 90
Connecting To A Dolby Digital Decoder Or An
Amplifier With Built-in DTS ............................ 91
SUBSIDIARY SETTINGS 92
Mode Set ........................................................... 92
VIDEO Plus+® System Setup ............................. 97
Tuner Set ........................................................... 98
Clock Set ......................................................... 104
Format A Disc ................................................. 106
Finalise A Disc ................................................ 107
Scan Mode Set ................................................. 108
Tray Lock ........................................................ 108
TROUBLESHOOTING 109
GLOSSARY 113
SPECIFICATIONS 114
LIST OF TERMS 115
DR-M10EK_01TOC.fm Page 5 Friday, February 27, 2004 2:30 PM
Filename [DR-M10EK_05DiscInfo.fm]
Masterpage:Left0
6
Page 6 March 16, 2004 2:12 pm
DISC INFORMATION
About Discs
Recordable/playable discs
You can use discs with the following logos for recording and
playback.
●The above table is based on the information as of February
2004.
●Recording and playback may not be performed with some
DVD-RAM, DVD-R/-RW, and CD-R/-RW discs depending on
the characteristics and condition of the disc used, leading to
unsatisfactory results. Using discs manufactured by JVC is
recommended since they have been tested to be compatible
with this unit.
DVD-RAM Discs
It is only possible to use discs which conform with DVD-RAM
standard Version 2.0. or 2.1
●It is impossible to record on DVD-RAM discs which do not
conform to this standard. If you use a disc formatted under a
different standard version, format it on this unit before use.
●It may not be possible to record, play back, edit or dub a
DVD-RAM disc even if it conforms to the standard if it was
recorded or edited on the devices from other manufacturers or
on a PC, or if it has far too many titles, or if there is very little
available capacity remaining on the disc.
●Some DVD-RAM discs are contained in a cartridge. This unit
cannot handle this type of disc. Remove the disc from the
cartridge (only discs with a removable cartridge); or the use of
DVD-RAM discs not contained in a cartridge is recommended.
●DVD-RAM discs recorded on this unit cannot be played back
on an incompatible DVD player.
●It is possible to record copy-once programmes of digital
broadcasts only onto 4.7/9.4 GB DVD-RAM discs (2.8 GB
DVD-RAM discs are not compatible).
DVD-R/RW Discs
It is only possible to use DVD-R discs which conform with
DVD-R standard Version 2.0.
This unit is not in compliance with DVD-RW Version 1.2.
When a DVD-R/RW disc (Video mode) is finalised (墌pg. 107),
it can be played back on a standard DVD player as a
DVD VIDEO disc.
When a DVD-RW disc (VR mode) is finalised (墌pg. 107), it
can be played back on a standard DVD player compatible with
the VR mode of DVD-RW discs.
Before finalising (墌pg. 107) —
— it is possible to record on unrecorded areas of the disc, edit
the disc title and programme titles, and delete programmes.
●Before finalising, it is possible to play or record DVD-R/RW
(Video mode) discs only on this unit.
●It is impossible to overwrite recorded areas of DVD-R discs.
●Available recording capacity does not increase even if a
recorded programme is deleted from a DVD-R disc.
After finalising (墌pg. 107) —
After a DVD-R/RW disc (Video mode) has been finalised, it is
possible to play back the recorded programmes (video and/or
audio) on a standard DVD video player as a DVD VIDEO disc.
●Edited titles are displayed as the “DVD menu” in video mode.
●It is impossible to record, edit or delete the data either in video
mode or in VR mode.
●Either in video mode or in VR mode, although the disc can be
played back on DVD players from other manufacturers,
sometimes it may not be possible to play depending on the
disc and recording conditions.
●It is impossible to record on CD-R/RW or DVD-R discs used
for authoring.
●It is impossible to record onto DVD-R/RW (Video mode) discs
broadcasts that allow you to copy once. The copy once
programmes can only be recorded onto DVD-RW discs
formatted in VR mode.
NOTE:
The following may result if you play back a DVD-R disc
recorded on another unit.
●The disc does not play.
●A mosaic pattern (block noise) appears on the screen.
●Video or audio may be dropped out.
●The unit stops during playback.
DVD-RAM 12 cm: 4.7 GB/9.4 GB
8 cm: 1.4 GB/2.8 GB
(VR mode)
Version 2.0
Version 2.1
DVD-R 12 cm: 4.7 GB
8 cm: 1.4 GB
General Version 2.0 (Video
mode)
DVD-RW 12 cm: 4.7 GB
Version 1.0 (VR mode)
Version 1.1 (Video mode /VR
mode)
DR-M10EK_05DiscInfo.fm Page 6 Tuesday, March 16, 2004 2:12 PM
Masterpage:Right-No-Heading
7
Filename [DR-M10EK_05DiscInfo.fm]
Page 7 February 25, 2004 5:57 pm
Discs for Playback Only
You can use discs with the following logos for playback only.
●Playback may not be performed depending on the
characteristics and condition of the disc used.
●DTS Audio CDs can also be played back (An optional DTS
decoder is required).
●MP3 and JPEG discs can be played back on this unit only
when they have been recorded in the ISO9660 or Joliet format
and finalised.
●JPEG files that can be played back on this unit must conform to
JFIF/Baseline process, and the maximum resolution of a JPEG
file is 3,840 x 2,160 pixels.
●CD-R/RW discs recorded in music CD format need to be
finalised to play on this unit.
●Operation and audio quality of this unit are not guaranteed for
discs that do not conform to the Compact Disc specification
(CD-DA).
Before you play back a CD, check for the CD logo and read
the notes on the package to confirm that it conforms to the
Compact Disc specification.
●Depending on the intentions of the author of the software,
recording conditions of DVD discs and Video CD/SVCD discs
may be restricted. Since this unit plays back discs according to
the intentions of the author of the software as indicated on the
disc, some functions may not operate as commanded.
●When switching from the first layer to the second layer of
double-layered DVD VIDEO discs, the image and sound may
be momentarily distorted. This is not a malfunction.
●DVD-AUDIO discs compatible with DVD video players can
be played.
●Super Audio CDs (SACD) compatible with conventional CD
players can be played.
Unplayable Discs
The following types of discs cannot be played using this unit.
Do not attempt to play back any kind of disc that is damaged
(cracked, warped, or repaired with adhesive tape) or discs in
unusual shapes (heart-shaped, octagonal, or other forms). If such
discs are accidentally played back, it may cause noise that can
lead to speaker damage.
●CD-ROM discs (including PHOTO-CD and CD-G)
●Discs recorded in Packet Write (UDF) format.
●1.3-GB double density CDs (DDCD)
●High density CDs (HDCD)
The following discs also cannot be played back.
●Discs of a region number other than “2”
●DVD-RAM (2.6 GB/5.2 GB)
Region Number
The world is divided into 6 regions for DVD VIDEO discs.
DVD VIDEO discs are assigned a region number to indicate
which region they may be played back in. A disc cannot be
played back on this unit unless the region number of the disc
matches that of the unit. The region number for this unit is “2”.
Only discs whose region number includes “2” or “ALL” can be
played back such as shown below.
Examples of DVD VIDEO labels which can be played back using
this unit.
Marks of discs in this instruction manual
DVD VIDEO
(example of region code
indications)
Video CD/Super Video CD
Audio CD
CD-DA
files
CD-R
CD-DA/
JPEG/MP3
files
CD-RW
CD-DA/
JPEG/MP3
files
CD-ROM
JPEG/MP3
files
Allows operation
with a DVD-RAM
disc.
Allows operation
with a Video CD/
Super Video CD
(SVCD) disc.
Allows operation
with a DVD-R disc.
Allows operation
with an Audio CD
disc.
Allows operation
with a DVD-RW
disc.
Allows operation
with a disc
including MP3 files.
Allows operation
with a DVD VIDEO
disc.
Allows operation
with a disc
including JPEG files.
DR-M10EK_01.book Page 7 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_05DiscInfo.fm]
Masterpage:Left+
8
Page 8 February 25, 2004 5:57 pm
DISC INFORMATION (cont.)
Recording Medium and Format
DVD-RAM
●Recording and erasing can be performed as many times as
possible on a disc.
●Editing can be performed after recording, such as deleting
unwanted parts.
●While recording, it is possible not only to start playback of a
programme currently being recorded, but also to watch
another programme previously recorded.
DVD-RW (VR mode)
●Recording and erasing can be performed as many times as
possible on a disc.
●Editing can be performed after recording, such as deleting
unwanted parts.
DVD-RW (Video mode)
●Can be played back on other DVD players.
●New recording can be performed by erasing all the data on a
disc once played back.
DVD-R
●Can be played back on other DVD players.
●Suitable when keeping a recorded disc for a long time.
File Structure of Discs
DVD VIDEO
Typically, DVD VIDEO discs are made up of larger units called
“titles”. Each title has a number (title number) that can be used
to select desired titles. Titles are further divided into units called
“chapters”. Each chapter has a number (chapter number) that
can also be used to select desired chapters. Note that some discs
are not divided into titles and chapters.
When you record a programme on a DVD-RAM/RW (VR mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted
when recording is paused, or audio changes from monaural or
bilingual to stereo due to commercial breaks, etc. It is also
possible to insert chapter marks at desired locations during
playback. (墌pg. 34)
When you record a programme on a DVD-R/RW (Video mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted
when recording is paused, or audio changes due to commercial
breaks, etc. It is also possible to insert chapter marks at desired
locations during either recording or playback. Once the disc has
been finalised, these chapter marks are deleted and new chapter
marks are assigned automatically approximately every 5
minutes.
●In Video mode, even before finalising, it is impossible to
perform editing operations other than changing the disc name
and/or title names and deleting programmes and/or titles.
●After finalising, it is impossible to perform editing operations.
Audio CD/Video CD/SVCD
Typically, Audio CD discs are divided into separate tracks each
containing one song. Each track is assigned a number. For
example, the third track is Track 3. The same is true for Video
CD/SVCD discs.
However, some discs are not divided into tracks.
S
DVD-RAM, DVD-RW, DVD-R or DVD VIDEO disc
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2 Chapter 3
Audio CD or Video CD/SVCD
Track 1 Track 2 Track 3 Track 4
DR-M10EK_01.book Page 8 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
9
Filename [DR-M10EK_05DiscInfo.fm]
Page 9 February 25, 2004 5:57 pm
JPEG/MP3 Disc (CD-R/RW/ROM)
MP3/JPEG files put in directories nested in several levels on a
disc will be organized as if they were put in single level
directories (groups) by the MP3/JPEG Navigation of this unit.
(墌pg. 78)
File structure of a disc before starting the MP3/JPEG Navigation
File structure of the disc after starting the MP3/JPEG
Navigation
Files are automatically grouped as follows and displayed on the
MP3/JPEG Navigation screen. Data is displayed in the
alphabetical order of file name. Files are grouped based on
roots.
●This unit can recognise up to 9 hierarchies including
directories and files.
Also, it can recognise up to 250 files in each group, and up to
99 groups on a disc.
NOTES:
●Video CD/SVCD discs that support Playback Control (PBC)
The contents of a disc are recorded into several hierarchies,
and played back according to the instructions on the screen
while navigating through the hierarchies. It is also possible to
playback recorded tracks consecutively without activating the
PBC function even when playing a PBC-compatible disc.
(墌pg. 36)
●Regarding the contents recorded on discs
Some files may not be played back depending on the file types
and other factors.
DVD VIDEO Marks
Sometimes marks are printed on a DVD disc and/or on its
packaging to indicate information regarding the contents and
functions of the disc. Check the marks indicating the contents
and functions of the disc. Note, however, that in some cases a
disc may not include a mark even for a function it supports.
Marks related to video
Marks related to audio
Directory
MP3 file
JPEG file
Mark Description
Number of subtitles
Number of angles
Recorded under the standard 4:3 aspect
ratio
Screen includes black bands at the top
and the bottom of image which has a
standard 4:3 aspect ratio (letter box)
Video playback is in Wide video mode
(16:9) on wide televisions, but in letter
box on televisions with standard 4:3
aspect ratio.
Video playback is in Wide video mode
(16:9) on wide televisions, but pan and
scan is used on televisions with standard
4:3 aspect ratio (either the left or right side
of the image is cut-out).
Mark Description
Number of audio tracks
Dolby Digital mark
It has been developed by Dolby
Laboratories as a digital surround system.
DTS (Digital Theater Systems)
You can enjoy DTS audio if you connect
an amplifier with a built-in DTS decoder
to the DIGITAL OUT connector of the
unit.
DR-M10EK_01.book Page 9 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_05DiscInfo.fm]
Masterpage:Left+
10
Page 10 February 25, 2004 5:57 pm
DISC INFORMATION (cont.)
Placing a Disc
Opening the disc tray
Press x on the unit or remote control to open the disc
tray.
●Pressing the button on the unit or on the remote control again
closes the disc tray.
●Use the buttons on the unit or on the remote control to open
and close the disc tray.
●Do not block the disc tray with your hand while it is opening
or closing as this may result in hardware failure.
●Do not place unplayable discs or any object other than a disc
on the disc tray.
●Do not press down strongly on the disc tray or place any heavy
objects on it.
Discs without cartridges
Place the disc on the disc tray with the label side facing up.
Since disc size changes depending on the disc to be played
back, be sure to correctly align the disc with the grooves for its
size. If the disc is not in its groove, it may be scratched or
otherwise damaged. To insert an 8 cm disc, place it according to
the inner groove.
DVD-RAM discs contained in cartridges
Double-sided discs:
Align the cartridge with the grooves on the disc tray as shown in
the illustration and insert with the label side you wish to play
back or record facing up. If you insert the disc with label “Side
A” facing up, programs are recorded on the side A.
Single-sided discs:
Align the cartridge with the grooves on the disc tray as shown in
the illustration and insert with the label side facing up.
Care and Handling of Discs
How to handle discs
When handling a disc, do
not touch the surface of the
disc. Since discs are made
of plastic, they are easily
damaged. If a disc gets dirty,
dusty, scratched or warped,
the images and sound will
not be picked up correctly,
and such a disc may cause the unit to malfunction.
Label side
Do not damage the label side, stick paper to or use any
adhesives on its surface.
Recording side
Make sure that discs are not scratched and dirty on the recording
side before use. Scratches and dirt on the recording side of a disc
may hinder proper playback and recording. Also be careful that
a DVD-RAM disc may get scratched or dirt when removed from
cartridge then put back in after use.
Storage
Make sure that discs are kept in their cases. If discs are piled on
top of one another without their protective cases, they can be
damaged. Do not put discs in a location where they may be
exposed to direct sunlight, or in a place where the humidity or
temperature is high. Avoid leaving discs in your car!
Maintenance of discs
If there are fingerprints or other dirt
adhering to a disc, wipe with a soft dry
cloth, moving from the centre outwards.
If a disc is difficult to clean, wipe with a
cloth moistened with water. Never use
record cleaners, petrol, alcohol or any
anti-static agents.
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
S-VIDEO VIDEO
L(MONO)
-
AUDIO
-
R
DV
DV IN
F1
REC MODE
PULL - OPEN
SAT#
VIDEO
Unit Remote control
1
STANDBY/ON
REC MODE
PULL - OPEN
Disc tray
CAUTION
Sometimes during playback, noise may appear or images
may be garbled. This is sometimes due to the disc. (It may not
be up to industry standards.)
These symptoms are caused by the discs, not by the
malfunction of the unit.
DR-M10EK_01.book Page 10 Friday, February 27, 2004 10:07 AM
Masterpage:Right0
11
Filename [DR-M10EK_06Name.fm]
Page 11 February 27, 2004 10:01 am
INDEX
FRONT VIEW
AInfrared Beam Receiving Window
BFront Display Panel 墌pg. 13
CDisc Tray
DOpen/Close Button (x (OPEN/CLOSE)) 墌pg. 10
EAutomatic Satellite Programme Recording Button
(SAT#) 墌pg. 65
FStop Button (8) 墌pg. 31, 53
GPlay Button (4 (PLAY)) 墌pg. 31
HPause Button (9 (PAUSE)) 墌pg. 31
IRecording Mode Button (REC MODE) 墌pg. 53
JRecord Button (7 (REC)) 墌pg. 53
KStandby/On Button (1 (STANDBY/ON))
墌pg. 21
LVideo Indicator (VIDEO) 墌pg. 54
MS-video/Video/Audio Input Connectors
(S-VIDEO/VIDEO/AUDIO (L/R)) 墌pg. 82
NDV Input connector (DV IN (i*)) 墌pg. 80
* i.Link refers to the IEEE1394-1995 industry specification and
extensions thereof. The i logo is used for products compliant with
the i.Link standard.
1
STANDBY/ON
S-VIDEO VIDEO
L(MONO)
-
AUDIO
-
R
DV
DV IN
F1
REC MODE
SAT#
VIDEO
K
C D FE G H I JBA
M NL
To access covered connectors, pull and open the
connector cover.
O
-
R
DV
DV IN
REC MODE
PULL - OPEN
DR-M10EK_01.book Page 11 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_06Name.fm]
Masterpage:Left+
12
Page 12 March 16, 2004 6:09 pm
INDEX (cont.)
REAR VIEW
AAntenna Input Connector (ANTENNA IN)
墌pg. 18
BComponent Video Output Connectors
(COMPONENT VIDEO OUT )墌pg. 20
CS-video Output Connector (S-VIDEO OUT)
墌pg. 19
DAudio Output Connectors
(AUDIO OUT (RIGHT/LEFT)) 墌pg. 19
EAV COMPU LINK Connector*
* Not function with this unit.
FDigital Audio Output Connectors
(DIGITAL OUT (COAXIAL/OPTICAL)) 墌pg. 86,
91
GCooling Fan
●This prevents the temperature from rising inside the unit.
Do not remove it.
●Install the unit so as not to block the area around the fan.
●The cooling fan on the rear of the unit may be activated even if the
unit is turned off in the following cases;
—In the Automatic Satellite Programme Recording standby mode
墌pg. 65, slightlybefore the starting time of PDC recording
墌pg. 59
—If you connect the decoder or the satellite receiver to L-2 IN/
DECODER connector and if “L-2 SELECT” is set to “DECODER”
or “SAT VIDEO” or “SAT S-VIDEO”. 墌pg. 85
—“JUST CLOCK” is set to “ON” 墌pg. 105 (Set “JUST CLOCK”
to “OFF” if you mind the noise of the fan.)
HMains Power Cord 墌pg. 18
IAntenna Output Connector (ANTENNA OUT)
墌pg. 18
JL-1 Input/Output Connector (L-1 IN/OUT)
墌pg. 18, 83, 84, 90, 91
KL-2 Input/Decoder Connector
(L-2 IN/DECODER) 墌pg. 28, 83, 90
LSatellite Control Connector (SAT CONTROL)
墌pg. 28
MRegion Number Label 墌pg. 7
DR-M10EK_06Name.fm Page 12 Tuesday, March 16, 2004 6:09 PM
Masterpage:Right-No-Heading
13
Filename [DR-M10EK_06Name.fm]
Page 13 February 27, 2004 10:01 am
FRONT DISPLAY PANEL
AVPS/PDC Indicator* 墌pg. 59
Appears when checking if the station being received
transmits a VPS/PDC signal.
* VPS (Video Programme System) recording is not currently
available in the U.K. and not possible with this unit.
Disc Type/Status Indicator
When a disc is loaded, the type of the disc is indicated.
When a disc is running, the disc marks rotate.
During High-Speed Search: Rotate faster than normal
playback.
During Slow Motion: Rotate slower than normal
playback.
While recording: Inner red ring lights in the same
way as normal playback. During
Instant Timer Recording (ITR),
inner red ring slowly blinks.
While paused: Disc marks blink when either
recording or playing back.
While stopped: Disc marks all light.
While resume stopped: Disc marks all blink.
While the disc tray opened: Disc marks all light out.
No disc on the disc tray: Disc marks all light out.
BVR Mode Indicator 墌pg. 106
Lights when a DVD-RW disc is formatted in VR mode.
CTimer Recording Indicator 墌pg. 56, 58, 60, 63
: Lights when a disc set up for On-Disc Timer
Programming is loaded.
: Lights when timer recording other than On-Disc
Timer Programming is on stand-by or being
executed.
: Lights when On-Disc Timer Programming is on
stand-by or being executed.
: Blinks quickly if you press # (TIMER) in the
following cases;
●Disc is not loaded.
●Clock has not been set.
●There is no programme setting.
DRecording Mode Indicator (XP/SP/LP/EP/FR)
墌pg. 54
Blinks when recording mode is being set.
While “FR” is blinking, the left 3 digits of the Multi Display
(L M) indicate setting values ranging from “60” to “480”.
After the value has been set, only “FR” lights.
EGroup/Title Indicator (GRP/TITLE) 墌pg. 8, 45
“GRP” or “TITLE” lights depending on a disc loaded while
the left 2 digits of the Multi Display (L) indicate the numbers
explained below.
“GRP”: Total number of groups or group number being
played back are displayed on the Multi Display.
“TITLE”: Total number of titles or title number being played
back are displayed on the Multi Display.
FTrack/Chapter Indicator (TRK/CHAP) 墌pg. 8, 45
“TRK” or “CHAP” lights depending on a disc loaded while
the 3rd and 4th digits from the left of the Multi Display (M)
indicate the numbers explained below.
“TRK”: Total number of tracks or track number being
played back are displayed on the Multi Display.
“CHAP”: Chapter number being played back are displayed
on the Multi Display.
DR-M10EK_01.book Page 13 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_06Name.fm]
Masterpage:Left+
14
Page 14 February 27, 2004 10:01 am
INDEX (cont.)
GSimulated Surround Effect Indicator (3D)
墌pg. 46
Lights when a simulated surround effect is set to “3D-ON” in
Play Set Up menu.
HLinear PCM Indicator (LPCM)
Lights when “XP MODE REC AUDIO” is set to “LINEAR
PCM” (墌pg. 94) for recording with DVD-RAM, DVD-R and
DVD-RW discs, and when Linear PCM audio is played.
IRandom/Programme Playback Mode Indicator
(RND/PRGM) 墌pg. 48
“RND”: Lights when Random Playback mode is set.
(墌pg. 48)
“PRGM”: Lights when Programme Playback mode is set.
(墌pg. 48)
JRepeat Mode Indicator ( /1/A–B) 墌pg. 44, 45
Select Repeat Playback mode in Play Set Up menu.
“ ”: Whole disc is played back repeatedly.
“ 1”: A single title/chapter/track is played back
repeatedly.
“ A–B”: The selected part (A–B) is played back
repeatedly.
No display: Repeat Playback mode is off.
KVideo Output Indicator ( ) 墌pg. 108
No display: Indicates that interlace mode is engaged.
: Indicates that progressive mode is engaged.
(Example) lights when video output mode is in
progressive mode.
LGroup/Title Number Display 墌pg. 8, 45
MTrack/Chapter Number Display 墌pg. 8, 45
NRemaining Time/Elapsed Time Indicator
墌pg. 34, 54
Lights when remaining time of DVD-RAM, DVD-R and
DVD-RW discs is displayed, and lights out when elapsed
time is displayed.
The right 6 digits of the Multi Display (O) indicate elapsed or
remaining time of each track.
No display: Indicates elapsed time of the disc.
Displayed: Indicates remaining time of the disc.
ORemaining Time/Elapsed Time Display
墌pg. 34, 54
PMulti Display
Displays clock, received channel, elapsed time, and
remaining time.
Also displays status of the unit (NO DISC/OPEN/CLOSE/
READING).
DR-M10EK_01.book Page 14 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
15
Filename [DR-M10EK_06Name.fm]
Page 15 February 27, 2004 10:01 am
ON-SCREEN DISPLAY
When “SUPERIMPOSE” is set to “AUTO” and ON SCREEN on the remote control is pressed, various operational
indicators appear on the TV screen. To clear the operational indicators, press ON SCREEN again.
ADisc Display
Displays the type of the disc loaded on the disc tray.
BTitle Number*
Displays number of the title currently being played back.
CPlayback Operation Status Indicator*
Indicates playback operation status by pictographs.
DPlayback Time*
Displays playback time of the title currently being played
back.
ERecording Mode
Displays recording mode as XP, SP, LP, EP, FR, FR60–FR360,
FR420 and FR480. Current recording mode is displayed
during recording, and recording mode in which the
programme was recorded is displayed during playback. The
recording mode is not displayed during play list playback.
FTitle Number
Displays playback title number during playback, and
recording title number during recording.
* During Live Memory playback, playback operation status is
displayed. During normal playback, the multichannel
encoding method is displayed.
GChapter Number
Displays playback chapter number during playback, and
recording chapter number during recording.
HClock Display
IBar Meter Display 墌pg. 39
Displays playback point and other information in bar meter.
JTitle Name Display
Displays title name newly registered to the title recorded on
DVD-RAM/RW/R discs, or file name of JPEG and MP3 files.
KOperation Status Indicator
Indicates operation status by pictographs. (Also indicates its
speed for forward high-speed search, reverse high-speed
search and slow motion.)
LTime Display
Displays single title playback elapsed time, single track playback
elapsed time, single track remaining time, total elapsed time,
total remaining time, and other information in turn.
MStation Name Display
Displays currently selected station name.
NAudio Display
Displays audio that is being input.
OInput Display
Displays currently selected input.
DR-M10EK_01.book Page 15 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_06Name.fm]
Masterpage:Left+
16
Page 16 February 27, 2004 10:01 am
INDEX (cont.)
REMOTE CONTROL
ATV Muting Button (TV ) 墌pg. 88
BTV AV/ VIDEO Button 墌pg. 54
CNumber Keys 墌pg. 32, 49, 53, 56, 70, 87, 99
Character Keys 墌pg. 70
DAuxiliary Button (AUX) 墌pg. 97
ECancel Button (& (CANCEL))
墌pg. 45, 48, 56, 63, 79, 100
FProgramme Check Button (PROG/CHECK)
墌pg. 63
GVIDEO Plus+ Button 墌pg. 56
HTop Menu Button (TOP MENU) 墌pg. 32
Irt Button 墌pg. 21
JMenu Button (MENU) 墌pg. 32
KReverse Skip Button (2) 墌pg. 32, 40
Previous Button (PREVIOUS) 墌pg. 36
LReverse Search Button (3) 墌pg. 33, 40
Reverse Slow Button (SLOW –) 墌pg. 33
MRecord Button (7 (REC)) 墌pg. 53
NRecording Mode Button (REC MODE) 墌pg. 53
OLive Check Button (LIVE CHECK) 墌pg. 40
PSet Up Button (SET UP) 墌pg. 25
QDisplay Button (DISPLAY)
墌pg. 15, 34, 39, 54
RAudio Button (AUDIO) 墌pg. 35
SSubtitle Button (SUBTITLE) 墌pg. 35
TTV/CABLE/SAT/DVD switch 墌pg. 21
UDVD STANDBY/ON Button (DVD 1) 墌pg. 21
VTV/CABLE/SAT STANDBY/ON Button (TV CBL
SAT 1) 墌pg. 88
WTV Volume Button (TV %+/–) 墌pg. 88
XProgramme Button (PR +/–) 墌pg. 89
YMemo Button (MEMO) 墌pg. 68, 75, 79
Mark Button (MARK) 墌pg. 34
ZAutomatic Satellite Programme Recording Button
(SAT#) 墌pg. 65
aTimer Button (# (TIMER)) 墌pg. 57, 59
bNavigation Button (NAVIGATION) 墌pg. 66
cwe Button 墌pg. 26, 40
dEnter Button (ENTER) 墌pg. 21
eReturn Button (RETURN) 墌pg. 36, 56
fForward Skip Button (6) 墌pg. 32, 40
Next Button (NEXT) 墌pg. 36
gForward Search Button (5) 墌pg. 33, 40
Forward Slow Button (SLOW +) 墌pg. 33
hPlay Button (4 (PLAY)) 墌pg. 31
Select Button (SELECT)
iPause Button (9 (PAUSE)) 墌pg. 31, 40
jStop Button (8) 墌pg. 31, 40, 53, 80
Clear Button (CLEAR) 墌pg. 33, 41, 48, 56
kSkip Search Button ( ) 墌pg. 33, 40
lOpen/Close Button (x (OPEN/CLOSE)) 墌pg. 10
mOne Touch Replay Button ( ) 墌pg. 40, 41
nPlay Set Up Button (ON SCREEN) 墌pg. 42
oProgressive Scan Button (PROGRESSIVE SCAN)
墌pg. 108
pAngle Button (ANGLE) 墌pg. 35
Buttons with a small dot on the left side of the name can also
be used to operate your TV. (墌pg. 88)
CABLE/SAT
DVDTV
DVD
PR
TIMER
SAT
#
PROG/CHECK
SHOW VIEW/
VIDEO Plus
+
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
TV/CBL/SAT
STANDBY/ON
TV TV AV
VIDEO
TV%
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
B
Hb
e
f
c
T
U
W
V
X
C
F
G
J
K
P
L
M
I
A
E
D
a
Z
g
d
h
i
j
l
k
n
o
p
m
Y
Q
R
S
N
O
How To Use
The remote control can operate most of your unit’s functions,
as well as basic functions of TV sets and satellite receivers of
JVC and other brands. (墌pg. 87, “Remote Control
Functions”)
●Point the remote control toward the receiving window.
●The maximum operating distance of the remote control is
about 8 m.
NOTES:
●When inserting the batteries, be sure to insert in the correct
directions as indicated under the battery cover.
●If the remote control doesn’t work properly, remove its
batteries, wait for approximately 5 minutes, replace the
batteries and then try operating the unit again.
DR-M10EK_01.book Page 16 Friday, February 27, 2004 10:07 AM
Masterpage:Right0
17
Filename [DR-M10EK_06Name.fm]
Page 17 February 27, 2004 5:49 pm
INSTALLING YOUR NEW UNIT
Check Contents
CHECK ALL THE CONTENTS SHOWN BELOW
4
You are now ready to install your unit. (墌pg. 18)
1
STANDBY/ON
S-VIDEO VIDEO
L(MONO)
-
AUDIO
-
R
DV
DV IN
F1
REC MODE
PULL - OPEN
CABLE/DBS
DVDTV
DVD
CH
TIMER
REC LINK
PROG/CHECK
VCR Plus+
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
TV/CBL/DBS
STANDBY/ON
TV
MUTING
TV/
VIDEO
TV VOLUME
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DBS
DEF
DVD Video Recorder
RF Cable “AA” Batteries (x 2)
Infrared Remote Control Unit
21-pin SCART Cable Satellite Controller
DR-M10EK_06Name.fm Page 17 Friday, February 27, 2004 5:52 PM
Filename [DR-M10EK_06Name.fm]
Masterpage:Left+
18
Page 18 February 27, 2004 10:01 am
INSTALLING YOUR NEW UNIT (cont.)
Basic Connections It’s essential that your unit be properly connected.
AInstall the unit.
Place the unit on a stable, horizontal surface.
BConnect the unit to a TV.
ADisconnect the TV aerial cable from the TV.
BConnect the TV aerial cable to the ANTENNA IN
connector on the rear panel of the unit.
CConnect the ANTENNA OUT connector on the rear
panel of the unit and the TV’s aerial connector with
the provided RF cable.
DConnect the L-1 IN/OUT connector on the rear panel
of the unit and the TV’s 21-pin SCART connector with
a provided 21-pin SCART cable.
●The L-1 IN/OUT connector accepts and delivers either a
composite signal (regular video signal), Y/C signal or RGB
signal.
●Select an appropriate option of “L-1 OUTPUT” as follows
(墌pg. 84):
●Set your TV to the VIDEO (or AV), Y/C, or RGB mode
according to the type of your TV’s SCART connector.
●For switching the TV’s mode, refer to the instruction manual of
your TV.
CConnect the unit to mains.
Connect the AC plug of the mains power cord into a
mains outlet.
●“LOADING” blinks on the front display panel when the AC
plug of the mains power cord is connected into a mains outlet,
and it takes the unit approximately 50 seconds to be turned
on. This is not a malfunction.
A
TTENTION:
Your TV must have a 21-pin AV input connector
(SCART) for the connection to the unit.
Back of TV
21-pin SCART connector
TV aerial
cable
RF cable
(provided)
21-pin SCART cable
(provided)
Mains power cord
Mains outlet
Back of unit
L-1 IN/OUT
ANTENNA IN
ANTENNA OUT
Aerial connector
THESE STEPS MUST BE COMPLETED BEFORE ANY
VIDEO OPERATION CAN BE PERFORMED.
When your TV’s SCART
connector accepts: Set “L-1 OUTPUT” to:
Y/C signal (separated
luminance (brightness) and
chrominance (colour) signals)
“SCART S-VIDEO”
RGB signal “SCART RGB”
After connection is completed, perform “Auto Set Up”
on page 21.
DR-M10EK_01.book Page 18 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
19
Filename [DR-M10EK_06Name.fm]
Page 19 February 27, 2004 10:01 am
S-VIDEO
Connection
8To connect to TV’s S-VIDEO input and AUDIO input
connectors
AConnect the unit to a TV.
AConnect the aerial, unit and TV as per “Basic
Connections”. (墌pg. 18)
BConnect the unit’s S-VIDEO OUT connector to the
TV’s S-VIDEO input connector.
CConnect the unit’s AUDIO OUT connectors to the
TV’s AUDIO input connectors.
BConnect the unit to mains.
Connect the AC plug of the mains power cord into a
mains outlet.
NOTES:
●You can obtain high-quality S-VHS pictures.
●With S-VIDEO connection, you cannot use the Preset
Download function. (墌pg. 23)
●If your TV is not stereo-capable, use the unit’s AUDIO OUT
connectors to connect to an audio amplifier for Hi-Fi stereo
sound reproduction.
●For switching the TV’s video input mode, refer to the
instruction manual of your television.
Back of TV
Aerial
connector
S-VIDEO input
connector
AUDIO input connectors
S-Video cable
(not provided)
Audio cable (not provided)
Mains outlet
Mains power cord
Back of unit
RF cable (provided)
S-VIDEO OUT
AUDIO OUT
TV aerial cable
ANTENNA IN
ANTENNA OUT
After the connection is completed, perform “Auto Set
Up” on page 21.
DR-M10EK_01.book Page 19 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_06Name.fm]
Masterpage:Left+
20
Page 20 February 27, 2004 10:01 am
INSTALLING YOUR NEW UNIT (cont.)
Component Video
Connection
Component video connection enables you to obtain high-quality
component video pictures.
8To connect to TV’s component video input connectors
AConnect the unit to TV.
APerform A–C in step B in “Basic Connections”
(墌pg. 18).
BConnect the unit’s COMPONENT VIDEO OUT
connectors to the TV’s component video input
connectors.
CConnect the unit’s AUDIO OUT connectors to the
TV’s AUDIO input connectors.
BConnect the unit to mains.
Connect the AC plug of the mains power cord into a
mains outlet.
NOTES:
●If your TV is not stereo-capable, use the unit’s AUDIO OUT
connectors to connect to an audio amplifier for Hi-Fi stereo
sound reproduction.
●For switching the TV’s video input mode, refer to the
instruction manual of your television.
Back of TV
Aerial
connector
Component Video
Input connectors
AUDIO input connectors
Component Video
cable
(not provided)
Audio cable (not provided)
Mains outlet
Mains power cord
Back of unit
RF cable (provided)
AUDIO OUT
TV aerial cable
COMPONENT VIDEO OUT
After the connection is completed, perform “Auto Set
Up” on page 21.
DR-M10EK_01.book Page 20 Friday, February 27, 2004 10:07 AM
Masterpage:Right0
21
Filename [DR-M10EK_06Name.fm]
Page 21 February 27, 2004 2:54 pm
INITIAL SETTINGS
Auto Set Up
Auto Channel Set/Auto Clock Set/
Auto Guide Program Number Set
ATurn on the unit.
On the unit
Press 1 on the unit.
On the remote control
Press DVD 1 on the remote control.
●The AUTO SET/T-V LINK display appears on the TV screen.
BPerform Auto Set Up.
●When you have connected the unit to a TV offering T-V Link
via a fully-wired 21-pin SCART cable (墌pg. 18) and the TV is
turned on, the unit automatically performs the Preset
Download (墌pg. 23) even if you select “AUTO SET” for Auto
Set Up function.
After the 1 button on the unit (or DVD 1 on the remote
control) is pressed for the first time to turn on the unit, the
Auto Set Up function sets the tuner channels, clock and
Guide Program numbers automatically.
F
1
STANDBY/ON
S-VIDEO VIDEO
L(MONO)
-
AUDIO
-
R
DV
DV IN
F1
REC MODE
SAT#
VIDEO
PULL - OPEN
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
DVD F
rt
ENTER
DVDTV
CABLE/SAT
Before starting, make sure of the following:
●The TV aerial cable should be connected to the unit.
●The unit’s mains power cord should be connected to a
mains outlet.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
Press rt to move the arrow
to “AUTO SET”, then press
ENTER.
“AUTO” blinks on the front display panel; do NOT
press any button on the unit or remote control until
the front display panel shows “– –:– –” as illustrated
on page 24.
●The AUTO SET screen will
appear.
DR-M10EK_06Name.fm Page 21 Friday, February 27, 2004 2:54 PM
Filename [DR-M10EK_06Name.fm]
Masterpage:Left+
22
Page 22 February 27, 2004 2:55 pm
INITIAL SETTINGS (cont.)
NOTES:
●In areas where no TV station transmits a PDC (Programme
Delivery Control) signal, the unit can perform neither Auto
Clock Set nor Auto Guide Program Number Set.
●If there is a power cut, or if you press 1 or SET UP while Auto
Set Up is in progress, Auto Set Up will be interrupted; be sure
to turn off the unit power once and try again from step A.
●Auto Clock Set may not function properly depending on the
reception condition.
A
TTENTION:
Once you have performed Auto Set Up, even if the unit’s
memory backup has expired, all the stored stations and their
Guide Program numbers remain in the unit’s memory and
the unit will not perform Auto Set Up again. The unit only
performs Auto Clock Set when the unit is turned on.
If you have moved to a different area, perform each setting as
required.
●Tuner setting (墌pg. 98)
●Clock setting (墌pg. 104)
If a new station starts broadcasting in your area, perform
tuner setting. (墌pg. 98, “Tuner Set”)
After “Auto Set Up” is completed, perform “Monitor
Set” on page 25.
DR-M10EK_06Name.fm Page 22 Friday, February 27, 2004 2:56 PM
Masterpage:Right-No-Heading
23
Filename [DR-M10EK_06Name.fm]
Page 23 February 27, 2004 2:55 pm
Preset Download
Auto Channel Set by Downloading
from TV/Auto Clock Set/Auto Guide
Program Number Set
NOTES:
●For details, refer to the instruction manual of your TV.
●In the area where no TV station transmits a PDC (Programme
Delivery Control) signal, the unit can perform neither Auto
Clock Set nor Auto Guide Program Number Set.
●If there is a power cut, or if you press 1 or SET UP while
downloading or set up is in progress, it will be interrupted; be
sure to turn off the unit power once and try again from the
beginning.
●Auto Clock Set may not function properly depending on the
reception condition.
●On this unit, the characters available for station names (ID) are
A–Z, 0–9, –, f, + and I (space). Some names of downloaded
stations may differ from those of your TV. (墌pg. 101, “Set
Stations (B)”)
If you have connected the unit to your TV via a 21-pin SCART
cable (墌pg. 18), the unit will automatically perform Preset
Download instead of the Auto Set Up in step B on page 21.
After downloading, the unit sets the clock and Guide Program
numbers automatically.
ATurn on the unit.
On the unit
Press 1 on the unit.
On the remote control
Press DVD 1 on the remote control.
●The AUTO SET/T-V LINK display appears on the TV screen.
BPerform Preset Download.
A
TTENTION:
You can use this function only with a TV offering T-V Link,
etc.* Be sure to use a fully-wired 21-pin SCART cable.
* Compatible with TVs offering T-V Link, EasyLink, Megalogic,
SMARTLINK, Q-Link or DATA LOGIC via a fully-wired 21-pin
SCART cable. The degree of compatibility and available functions
may differ by system.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
TV/CBL/SAT
TV TV AV
VIDEO
TV%
SHOW VIEW/
VIDEO Plus
+
rt
ENTER
DVDTV
CABLE/SAT
DVD F
●Slide the TV/CABLE/SAT/DVD switch to DVD.
Press rt to move the arrow
to “T-V LINK” and press
ENTER.
Preset positions on the front display panel increase from
“PR 1”; do NOT press any button on the unit or remote
control until the front display panel shows clock time, “PR 1”
or “– –:– –” as illustrated on page 24.
●The T-V LINK screen will
appear. When Preset
Download is completed,
“COMPLETED” appears for
about 5 seconds, then the
normal screen appears.
●If you press any button on the
unit or remote control while
downloading is in progress, it
will be interrupted.
After “Preset Download” is completed, perform
“Monitor Set” on page 25.
DR-M10EK_06Name.fm Page 23 Friday, February 27, 2004 2:57 PM
Filename [DR-M10EK_06Name.fm]
Masterpage:Left+
24
Page 24 February 27, 2004 10:01 am
INITIAL SETTINGS (cont.)
Results of Auto Set Up/Preset Download appearing on the front display panel
If both Auto Channel Set and Auto Clock Set have been performed successfully, the
correct current time is displayed.
Turn on the TV and select its AV mode, then make sure that all necessary stations have been stored
in the unit’s memory by using the PR +/– button(s).
●If station names (ID – 墌pg. 102) have also been stored in the unit’s memory, the station name
will be displayed at the top right corner of the TV screen for about 5 seconds when the unit is
tuned to a different station.
●If you want to set the tuner manually such as to add or skip channels, to change channel
positions, or to set or change station names, see pages 99 – 102.
If Auto Channel Set has succeeded but Auto Clock Set has not, “PR 1” (channel
position) is displayed.
OR
If both Auto Channel Set and Auto Clock Set have failed, “– –:– –” is displayed.
ATurn on the TV and select its AV mode, then make sure that all necessary stations have been
stored in the unit’s memory by using the PR +/– button(s).
●If station names (ID – 墌pg. 102) have also been stored in the unit’s memory, the station name
will be displayed at the top right corner of the TV screen for about 5 seconds when the unit is
tuned to a different station.
●If you want to set the tuner manually such as to add or skip channels, to change channel
positions, or to set or change station names, see pages 99 – 102.
BPerform “Clock Set” on page 104.
NOTE:
After making sure the cables are connected properly, turn off the unit’s power once, then turn the
unit’s power back on again.
Perform “Auto Set Up” on page 21 or “Preset Download” on page 23 again.
IMP
O
RTANT:
●To check if the Guide Program numbers have been set correctly, perform the VIDEO Plus+ Timer Programming. (墌pg. 56)
●In certain reception conditions, station names may not be stored correctly, and auto Guide Program Number Set may not work
properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the VIDEO Plus+
system, the unit will record a TV programme of a different station. When programming the timer using the VIDEO Plus+ system,
be sure to check the desired channel is selected correctly. (墌pg. 56, “VIDEO Plus+® Timer Programming”)
●Your unit memorizes all detected stations even if reception of some of them is poor. You can delete those stations with an
unacceptable picture. (墌pg. 100, “Delete A Channel”)
INFORMATION
Just Clock
Your unit is equipped with the Just Clock function which provides accurate time keeping through automatic adjustments at regular
intervals, by reading data from a PDC signal. If you want to take advantage of this function, simply set it to “ON”. (墌pg. 104, “Just
Clock”)
If you have any difficulty with the above procedures call the JVC Customer Service Hot Line
on 0870 330 5000
DR-M10EK_01.book Page 24 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
25
Filename [DR-M10EK_06Name.fm]
Page 25 February 27, 2004 10:01 am
Monitor Set
You can select the monitor type depending on the TV
used when you play back DVD VIDEO discs recorded for
wide-screen TVs.
AAccess the Main Menu screen.
Press SET UP.
BAccess the “VIDEO IN/OUT” screen.
CSelect the desired option.
APress rt to select “MONITOR TYPE”, then press
ENTER.
BPress rt to select the desired option, then press
ENTER.
DComplete the setting.
Press SET UP.
(The boldface settings in the table below indicate the settings at
your purchase.)
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
APress we to move the
arrow to “FUNCTION SET
UP”, then press ENTER.
BPress we to move the
arrow to “VIDEO IN/
OUT”, then press ENTER.
8MONITOR TYPE
4:3LB (Letter Box conversion):
Select this when the aspect ratio of your TV is
4:3 (conventional TV). While viewing a wide
screen picture, the black bars appear on the
top and the bottom of the screen.
4:3PS (Pan&Scan):
Select this when the aspect ratio of your TV is
4:3 (conventional TV). While viewing a wide
screen picture, the black bars do not appear;
however, the left and right edges of the
pictures will not be shown on the screen.
16:9 AUTO (Wide television conversion):
Select this when the aspect ratio of your TV is
16:9 (wide TV).
16:9 FIX (Wide television conversion):
Select this when the aspect ratio of your TV is
fixed to 16:9 (wide TV). The unit automatically
adjusts the screen width of the output signal
correctly when playing back a picture whose
aspect ratio is 4:3.
Pan&Scan/Letter Box
In general, DVD VIDEO disc are produced for a wide-screen
TV with 16:9 aspect ratio.
Material with this ratio will not fit to a TV with 4:3 aspect
ratio. There are two styles to display the image, “Pan&Scan”
(PS) and “Letter Box” (LB).
Pan&Scan
The right and left side of the image are
cut off. The image fills the screen.
●The picture will be shown in the
“4:3LB” mode depending on the disc
even if the “4:3PS” mode is selected.
Letter Box
Black bands appear at the top and
bottom of the image. The image itself
appears in 16:9 aspect ratio.
DR-M10EK_01.book Page 25 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_06Name.fm]
Masterpage:Left+
26
Page 26 February 27, 2004 2:58 pm
INITIAL SETTINGS (cont.)
Language
On-screen Language Set
This unit offers you the choice to view on-screen
messages in 10 different languages. You can change the
language setting manually as required.
AAccess the Main Menu screen.
Press SET UP.
BAccess the “DISPLAY SET” screen.
CSelect the desired language.
APress rt to move the arrow to “ON SCREEN
LANGUAGE”, then press ENTER.
BPress rt to select your desired language, then press
ENTER.
DComplete the setting.
Press SET UP.
Menu/Audio/Subtitle Language Set
Some DVD discs contain the DVD menu display, audio
and subtitles in multiple languages. With these discs, you
can set the default language as you like.
●The procedure shows how to set “MENU LANGUAGE”
as an example.
AAccess the Main Menu screen.
Press SET UP.
BAccess the “LANGUAGE SET” screen.
CSelect the desired language.
APress rt to move the arrow to “MENU
LANGUAGE”, then press ENTER.
●See “Language Code Listl” (墌pg. 27).
BPress rt to select your desired language, then press
ENTER.
DComplete the setting.
Press SET UP.
NOTE:
When the selected language is not available on the disc, the
disc’s default menu language is played back.
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
APress we to move the
arrow to “FUNCTION SET
UP”, then press ENTER.
BPress we to move the
arrow to “DISPLAY SET”,
then press ENTER.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
TV/CBL/SAT
TV TV AV
VIDEO
TV%
SHOW VIEW/
VIDEO Plus
+
rtwe
ENTER
SET UP
DVDTV
CABLE/SAT
APress we to move the
arrow to “DVD SET UP”,
then press ENTER.
BPress we to move the
arrow to “LANGUAGE
SET”, then press ENTER.
DR-M10EK_06Name.fm Page 26 Friday, February 27, 2004 2:58 PM
Masterpage:Right 3Column
27
Filename [DR-M10EK_06Name.fm]
Page 27 February 27, 2004 2:59 pm
Language Code List
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DZ
EL
EO
ET
EU
FA
FJ
FO
FY
GA
GD
GL
GN
GU
HA
HI
HR
HU
HY
IA
IE
Afar
Abkhazian
Afrikaans
Ameharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Fiji
Faroese
Frisian
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
IK
IN
IS
IW
JI
JW
KA
KK
KL
KM
KN
KO
KS
KU
KY
LA
LN
LO
LT
LV
MG
MI
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
OC
OM
OR
PA
PL
PS
PT
QU
RM
Inupiak
Indonesian
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean (KOR)
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay (MAY)
Maltese
Burmese
Nauru
Nepali
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Portuguese
Quechua
Rhaeto-Romance
RN
RO
RU
RW
SA
SD
SG
SH
SI
SK
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Wolof
Xhosa
Yoruba
Zulu
DR-M10EK_06Name.fm Page 27 Friday, February 27, 2004 2:59 PM
Filename [DR-M10EK_06Name.fm]
Masterpage:Left0
28
Page 28 February 27, 2004 10:01 am
SAT CONTROL SET
Satellite Receiver
Control Setting
The following procedure is required if you receive
satellite channels through a satellite receiver.
Approximately 20 seconds before the VIDEO Plus+ timer
programming (墌pg. 56) or Manual Timer programming
(墌pg. 58) starts, the unit sets its input mode to “L-2” and
automatically switches the satellite receiver’s channels
using a provided Satellite Controller.
Installing Satellite Controller
AInstall a Satellite Controller.
Place a Satellite Controller so that the path between its
transmitter and the satellite receiver’s remote sensor is
unobstructed.
BAttach the Satellite Controller.
Fix securely using the adhesive strip attached on the back
of the Satellite Controller.
CMake connections.
Be sure to connect the unit’s L-2 IN/DECODER connector
to the satellite receiver’s 21-pin SCART connector.
NOTE:
When connecting your satellite receiver, refer to its instruction
manual.
DConnect the Satellite Controller to unit.
Connect the Satellite Controller to the SAT CONTROL
connector on the rear panel.
Satellite receiver
Satellite Controller
(provided)
(suggested locations)
Transmitter
21-pin SCART cable
(provided)
SAT CONTROL
L-2 IN/DECODER
Your unit
Satellite Controller
(provided)
Satellite receiver
Back of unit
DR-M10EK_01.book Page 28 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
29
Filename [DR-M10EK_06Name.fm]
Page 29 February 27, 2004 10:01 am
Setting satellite receiver’s brand and
channel
After installation, set the satellite receiver’s brand and
channel correctly; otherwise, the Satellite Controller
cannot work correctly.
ATurn on the satellite receiver.
Turn on the satellite receiver’s power.
BAccess the Main Menu screen.
Press SET UP.
CAccess the “SAT/GUIDE PR” screen.
DSelect the satellite receiver’s brand.
APress rt to move the arrow to “SAT BRAND”, then
press ENTER.
BPress rt to select the brand code from the list on
page 30, then press ENTER.
●If the brand code you entered is invalid, the code field will be
reset. Enter the correct brand code again.
●If the unit is in playback or recording mode, you cannot set the
brand code.
ESelect the satellite receiver’s channel for
testing.
rtwe
ENTER
0 – 9
SET UP
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
DEF
CABLE/SAT
PR
SAT
#
TV/CBL/SAT
TV TV AV
VIDEO
TV%
SHOW VIEW/
VIDEO Plus
+
MEMO/MARK
DVDTV
CABLE/SAT
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
APress we to move the
arrow to “INITIAL SET
UP”, then press ENTER.
BPress we to move the
arrow to “SAT/GUIDE
PR”, then press ENTER.
Press the appropriate number
keys to enter one of the
channel positions on the
satellite receiver, then press
ENTER twice.
●You can select the channel
position between 1 to 999.
●After pressing ENTER, the unit
enters the Test mode.
DR-M10EK_01.book Page 29 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_06Name.fm]
Masterpage:Left
30
Page 30 February 27, 2004 10:01 am
T-V LINK
FCheck the result of the test.
If the satellite receiver’s channel number has not been
changed correctly
Press we to move the arrow to “NO”, then press ENTER.
Then perform the procedure again from step D.
NOTES:
●The Satellite Controller may not work with all types of satellite
receiver.
●For some satellite receivers, you need to set its channel input
mode to 2-digit.
●If your satellite receiver has more than two channel modes, be
sure to set to “All Channel Mode”. For details, refer to the
instruction manual of the satellite receiver.
●When selecting the satellite receiver’s channel (墌 step E),
signals from the remote control may interfere with signals
transmitted from the Satellite Controller. In this case, move the
remote control as close to the unit’s infrared beam receiving
window as possible.
T-V Link Functions
When you connect the unit to your TV via a fully-wired 21-pin
SCART cable (墌pg. 18), the following functions are available.
You can use these functions only with a TV offering T-V Link,
etc.*
For details, refer to the instruction manual of your TV.
* Compatible with TVs offering T-V Link, EasyLink, Megalogic,
SMARTLINK, Q-Link or DATA LOGIC via a fully-wired 21-pin SCART
cable. The degree of compatibility and available functions may differ by
system.
TV Auto Power On
The TV will turn on and be set to its AV mode automatically
whenever you start playback.
For details, refer to the instruction manual of your TV.
Unit Auto Standby
You can use your TV’s remote control to turn off the unit.
For details, refer to the instruction manual of your TV.
Direct Rec
You can easily start recording the programme that you are
watching on your TV. When you use this function, set “DIRECT
REC” to “ON”. (墌pg. 94)
If the satellite receiver’s
channel number has been
changed to the same one as
you set in step E.
Press we to move the arrow
to “YES”, then press ENTER
to finish the Sat Control Set
mode.
BRAND NAME CODE
JVC
AMSTRAD
ASTON
CANAL SATELLITE
CANAL +
D-BOX
ECHOSTAR (VIA DIGITAL)
FINLUX
FORCE
GALAXIS
GRUNDIG
HIRSCHMANN
HUMAX
ITT NOKIA
JERROLD
KATHREIN
LUXOR
MASCOM
MASPRO
NOKIA
PACE
PANASONIC
PHILIPS
RADIX
RFT
SABA
SAGEM
SALORA
SAMSUNG
SIEMENS
SKYMASTER
TECHNISAT
THOMSON
TPS
TRIAX
WISI
73
60, 61, 62, 63, 92
97
81
81
85
82
68
89
88
64, 65, 102
64, 78, 99
88
68
75
70, 71, 96
68
93
70
87, 94
65, 67, 74, 86, 92, 97
74, 92
66, 84, 101
78
69
97
83, 90
68
83
64
69, 98
66, 100
97
83
91
64
DR-M10EK_01.book Page 30 Friday, February 27, 2004 10:07 AM
Masterpage:Right0
31
Filename [DR-M10EK_07Playback.fm]
Page 31 February 25, 2004 5:59 pm
PLAYBACK OPERATIONS
Basic Playback To play back an MP3/JPEG disc, see “Playback with MP3/JPEG
Navigation” (墌pg. 78).
ALoad a disc.
APress x to open the disc tray.
BPlace the disc on the disc tray.
●For details, refer to “Placing a Disc” (墌pg. 10).
CPress x to close the disc tray.
●Pressing 4 also closes the disc tray.
●Playback begins automatically if an auto-playback DVD disc is
loaded.
BStart playback.
Press 4.
●If you load a DVD disc whose region code does not match the
unit, “REGION CODE ERROR” appears on the TV screen. For
details, refer to “Region Number” (墌pg. 7).
●With Video CD/SVCD discs with PBC control or some DVD
discs, the menu display may appear on the TV screen after
starting playback. In this case, select an item which you want
to play back from the menu. Otherwise, the playback cannot
go forward. Refer to “Locating a desired scene using the menu
of a Video CD/SVCD with PBC” (墌pg. 36) or “Locating a
desired scene using the DVD menu” (墌pg. 32).
●The Library Database DVD Navi also enables you to search
and select the desired programmes. (墌pg. 66)
CPause playback.
Press 9.
●To resume normal playback, press 4.
DStop playback.
Press 8.
●When a recordable disc is played, playback stops and a
programme received with the unit’s tuner resumes on the TV
screen.
●When a playback-only disc is played, playback stops and the
still image at the time you press 8 remains on the TV screen.
Pressing 8 again resumes a programme received with the
unit’s tuner.
●If x is pressed during playback, playback stops, then the disc
tray opens.
NOTE:
When the Library Database DVD Navi screen appears, choose a
thumbnail image of the desired programme on the TV screen,
then press SELECT or ENTER. (墌pg. 68)
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
A
TTENTION:
●It takes approximately 30 seconds to read a disc depending
on the type and condition of the disc since this unit is
multi-disc compatible (DVD-RAM, DVD-RW, DVD-R). It
may even take several minutes when a disc is dirty,
scratched or warped.
●It may take a few seconds to start playback. This is not a
malfunction.
●Forward/reverse high-speed search and other operations
cannot be performed while playback is stopped.
1
STANDBY/ON
S-VIDEO VIDEO
L(MONO)
-
AUDIO
-
R
DV
DV IN
F1
REC MODE
SAT#
VIDEO
PULL - OPEN
8
x4
9
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PA U S EREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
TV/CBL/SAT
TV TV AV
VIDEO
TV%
SHOW VIEW/
VIDEO Plus
+
4
SELECT
rtwe
ENTER
x
9
8
DVDTV
CABLE/SAT
DR-M10EK_01.book Page 31 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_07Playback.fm]
Masterpage:Left+
32
Page 32 February 25, 2004 5:59 pm
PLAYBACK OPERATIONS (cont.)
Playback Features
Locating a desired scene using the
DVD menu
DVD VIDEO discs may have top menu and disc menu.
Top menu
DVD discs generally have their own menus which show the disc
contents. These menus contain various items such as titles of a
movie, names of songs, or artist information. You can locate a
desired scene by using the top menu displayed on the TV screen.
Press TOP MENU to access the top menu.
Disc menu
Disc menus include playback data (angle menu, subtitle menu,
etc.) specific to each title.
Press MENU to access the disc menu.
1Access the DVD menu.
2Start playback.
Press rt w e to select a desired title, then press ENTER.
●It may be possible to select the desired item using the number
keys depending on the menu display.
NOTE:
When “X” appears on the TV screen in step 1, the disc does not
have a top menu or disc menu.
Locating the start point of the item or
skip the item
Press 2 or 6 during playback.
●Pressing 6 locates the start point of the item or skips the
item for forward direction, then resumes playback.
●Pressing 2 locates the start point of the item or skips the
item for reverse direction, then resumes playback.
When a DVD-RAM/RW/R disc is played
Example:
To locate the beginning of the next item, press 6 once.
To locate the beginning of the current item, press 2 once.
To locate the beginning of the previous item, press 2 three
times.
When a DVD VIDEO, Audio CD or Video CD/SVCD disc
is played
Example:
To locate the beginning of the next item, press 6 once.
To locate the beginning of the current item, press 2 once.
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
Press TOP MENU or MENU.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
TV/CBL/SAT
TV TV AV
VIDEO
TV%
SHOW VIEW/
VIDEO Plus
+
rtwe
ENTER
8x
DVD 1
0 – 9
MENU
2
9
4
6
5
/SLOW+
TOP MENU
3
SLOW–
Example:
●: marked points (墌pg. 34)
Current programme
Drama
Previous
programme
News Next
programme Movie
Reverse Forward
Playback point
Reverse Forward
Scene 2
(Chapter 2)
or
Track 2
Scene 3
(Chapter 3)
or
Track 3
Scene 4
(Chapter 4)
or
Track 4
DR-M10EK_01.book Page 32 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
33
Filename [DR-M10EK_07Playback.fm]
Page 33 February 25, 2004 5:59 pm
High-Speed Search
During playback, press 5 for forward high-speed
search, or 3 for reverse high-speed search.
●Each press of the button increases the search speed for each
direction.
●To resume normal playback, press 4.
OR
During playback, press and hold 6 for 2 or more
seconds for forward high-speed search, or press and hold
2 for 2 or more seconds for reverse high-speed search.
●Releasing the button resumes normal playback.
Still Picture/Frame-By-Frame
Playback
1Pause during playback.
Press 9.
2Activate frame-by-frame playback.
Press 9.
●Each press of 9 advances the still picture frame by frame.
OR
Press we.
●Each press of we advances/reverses the still picture frame by
frame.
●Frame-by-frame playback for reverse direction cannot be
performed with Video CD/SVCD discs.
●To resume normal playback, press 4.
Slow Motion
While paused, press SLOW – or SLOW +.
●Each press of SLOW – or SLOW + increases the slow motion
speed for each direction (from 1/16 to 1/2 times the normal
speed).
●Slow motion for reverse direction cannot be performed with
Video CD/SVCD discs.
OR
Press 2 or 6 for 2 or more seconds.
Skip Search
During playback, press .
●Each press initiates an approximately 30-second period of fast-
motion playback. Normal playback resumes automatically.
Resume Function
It is possible to memorise the position where you stop playback
and resume playback from that position.
●Be sure to set “RESUME” to “ON” or “DISC RESUME”.
(墌pg. 96)
1Memorize a resume point.
Press 8 during playback.
●The unit enters Resume Stop mode and memorises the
position where you have stopped playback as a resume point.
(The inside of the disc status indicator on the front display
panel blinks in the Resume Stop mode.)
●The unit retains a memory of the resume points of the last 30
discs played back, even though they have been ejected if
“RESUME” is set to “DISC RESUME”. (墌pg. 96)
●To clear the resume points:
(The inside of the disc status indicator stops blinking and
lights.)
When “RESUME” is set to “ON”:
• Press 1 on the unit or DVD1 on the remote control to
turn off the unit.
• Press x to take out the disc.
• Press 8 in stop mode.
• Press TOP MENU to display the top menu, then start
playback by selecting an item, etc.
• Press MENU to display the disc menu, then start playback by
selecting an item, etc.
When “RESUME” is set to “DISC RESUME”:
• Set “RESUME” to “OFF”. (墌pg. 96)
• Press 8 in stop mode.
• Press TOP MENU to display the top menu, then start
playback by selecting an item, etc.
• Press MENU to display the disc menu, then start playback by
selecting an item, etc.
2Resume playback.
Press 4 in stop mode. The unit starts playback from the
resume point.
NOTES:
●“DISC RESUME” setting works on DVD VIDEO, VCD, SVCD
and already finalised DVD-R/DVD-RW (video mode) discs. For
other types of discs, the function under “ON” setting will be
applied even if “RESUME” is set to “DISC RESUME”.
(墌pg. 96)
●If you stop the playback of a disc for which an resume point
has already been memorized, the memory will be updated
with the new resume point.
●After the unit has memorized the resume point for 30 discs,
remembering a new resume point will cause the unit to delete
the oldest memorized point. Stopping playback of a disc for
which a resume point is already stored may change the order
in which the points are stored. This may potentially change the
order in which points are deleted.
●When the unit memorizes a resume point for a disc, it also
remembers audio language, subtitle and angle settings.
●This function may not work for some Video CD or SVCD.
●When “RESUME” is changed to “ON” or “OFF”, resume
points of the discs memorized with “RESUME” set to “DISC
RESUME” will be cleared.
●Resume points are memorized for each side of a double-sided
disc.
DR-M10EK_01.book Page 33 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_07Playback.fm]
Masterpage:Left+
34
Page 34 February 25, 2004 5:59 pm
PLAYBACK OPERATIONS (cont.)
Marking positions to play again later
It is possible to mark positions (up to 999 points) where you
want to play back once again later, and start playback from a
marked position. Marking onto DVD-RAM/RW/R discs when
recording is helpful to locate a start point when you play back
the discs later.
1Mark positions.
2Delete the marked positions.
NOTES:
●When a monaural programme or bilingual programme
changes to a stereo programme while recording, a mark signal
is automatically recorded.
●When a DVD-R/RW (Video mode) disc is finalised, marked
points marked before finalising will be deleted, and
programmes will be divided automatically into “chapters”
approximately every 5 minutes. (墌pg. 107, “Finalise A
Disc”)
Checking the time information
You can change the counter display on the front display panel
and TV screen to check disc remaining time (only discs before
finalising).
During playback
Each press of DISPLAY changes the display as follows:
Clock time (front display panel only) ] Current title elapsed
time ] Disc remaining time ] (back to the beginning)
●Clock time is displayed only when a recordable disc is played.
In stop mode or during playback
●In FR mode, it is possible to set recording time in detail using
we. (墌pg. 55, “Free Rate Function”)
●It is not possible to switch the recording mode during playback
or while recording.
Switching Time Indication
You can check time information of an audio CD and a Video
CD/SVCD on the front display panel and the TV screen.
Each press of DISPLAY changes the time indication as follows:
During playback
Current track elapsed time ] Current track remaining time ]
Total elapsed time ] Total remaining time ] (back to the
beginning)
In stop mode
0:00 ] Playback time of track 1 ] 0:00 ] Total length of a disc
] (back to the beginning)
NOTE:
When a PBC-compatible Video CD/SVCD disc is loaded,
deactivate the PBC function. (墌pg. 36)
During playback, press
MARK at positions you want
to mark.
●“MARK” appears on the TV
screen. You can easily locate
the marked positions using
2 or 6 when you play
back the disc.
While paused, press 2 or
6 to locate a marked
position you want to delete,
then press MARK.
●Crossed “MARK” appears on
the TV screen, and the marked
position is deleted.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
TV/CBL/SAT
TV TV AV
VIDEO
TV%
SHOW VIEW/
VIDEO Plus
+
MARK
MENU
26
ANGLE
SUBTITLE
AUDIO
DISPLAY
we
ENTER
DR-M10EK_01.book Page 34 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
35
Filename [DR-M10EK_07Playback.fm]
Page 35 February 25, 2004 5:59 pm
Angle Selection
You can enjoy a variety of scene angles if a DVD VIDEO disc
contains “multi-angle” parts, where the same scene was shot
from different angles.
If the disc contains “multi-angle” parts, “ ” appears on the TV
screen at the beginning of the “multi-angle” part.
1Access Angle display.
2Select the angle.
Press ANGLE or we to select your desired angle.
●Each time you press ANGLE or we, the angle changes.
●When “X” appears on the TV screen, the current scene is not
recorded from multiple angles. In addition, some discs
prohibit angle selection.
●To clear the angle selection display, press ENTER. In addition,
the angle selection display disappears automatically if no
operation is done for 10 seconds.
Subtitle Selection
Some DVD VIDEO discs contain more than one subtitle
language, from among which you can choose the desired
subtitle language. “ ” appears on the TV screen at the
beginning of the part where more than one subtitle language are
recorded.
1Access Subtitle display.
2Select the subtitle language.
Press we to select your desired language.
●To clear the subtitle selection display, press ENTER.
NOTES:
●When “X” appears on the TV screen, no subtitle language is
recorded.
●When the subtitle language won’t be changed with the
procedure above, change the subtitle on a disc menu
displayed by pressing MENU.
●It is not possible to play back SVCD discs with subtitles.
Audio Language/Sound Selection
Some DVD VIDEO discs contain the multiple audio language or
sound. You can select the desired audio language or sound. For
some Video CD/SVCD discs, you can switch the audio channel
to choose Karaoke either with or without the vocal.
1Access Audio Language/Sound selection display.
2Select the audio language/sound.
Each time you press AUDIO or we, the audio language/
sound changes.
●To clear the Audio Language/Sound selection display, press
ENTER.
NOTES:
●When “X” appears on the TV screen, no audio language is
recorded.
●When the audio language won’t be changed with the
procedure above, change the audio on a disc menu displayed
by pressing MENU.
Press ANGLE during
playback.
●The angle selection display
appears on the TV screen.
Press SUBTITLE during
playback.
●The subtitle selection display
appears on the TV screen.
●Each time you press
SUBTITLE, the subtitle display
is switched on and off.
(When 3 scene angles are
contained.)
(When 3 subtitle languages
are contained.)
Press AUDIO during
playback.
(When 3 audio languages are
contained.)
DR-M10EK_01.book Page 35 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_07Playback.fm]
Masterpage:Left+
36
Page 36 February 25, 2004 5:59 pm
PLAYBACK OPERATIONS (cont.)
Audio Channel Selection
When watching bilingual programmes or playing discs on which
you recorded bilingual or stereo programmes, you can choose
the desired audio channel.
●When “SUPERIMPOSE” is set to “AUTO”, you can confirm on
the TV screen the audio channel you have chosen. (墌pg. 95)
●Each time you press AUDIO, the audio channel changes.
NOTE:
It is not possible for DVD-R/DVD-RW (Video mode) disc
playback to switch the audio channel. The audio channel is
played back as set in “AUDIO REC” (墌pg. 94).
Playback Control (PBC) Function
— Locating a desired scene using the
menu of a Video CD/SVCD with PBC
Some Video CD/SVCD discs support the PBC function. PBC is an
abbreviation of “Play Back Control”. A Video CD/SVCD disc
recorded with PBC has its own menus, such as a list of the songs
on the disc. You can locate a specific scene by using the menu.
1Access the PBC menu.
In stop mode
Press 4.
2Start playback.
Press the number keys to enter the number of the desired
scene.
●The unit starts playback of the selected item. “PBC” appears on
the front display panel.
●When “NEXT” or “PREVIOUS” appears on the TV screen:
Pressing NEXT advances to the next page.
Pressing PREVIOUS returns to the previous page.
●You can return to the menu by pressing RETURN.
●The method of the operation is different depending on the
disc.
NOTES:
●If you want to playback a PBC-compatible Video CD/SVCD
disc without activating the PBC function, start playback in stop
mode by using the number keys, instead of the 4 button, to
choose the track, then press ENTER.
●To activate the PBC function when a PBC-compatible Video
CD/SVCD disc is being played back without the PBC function,
press TOP MENU, or press 8 then press 4.
TRACK
USE
On-Screen
Display
For main and sub audio of bilingual
programme
For main audio of bilingual programme
For sub audio of bilingual programme
For stereo discs
For audio of left channel
For audio of right channel
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
PR
SAT
#
TV%
SHOW VIEW/
VIDEO Plus
+
8
0 – 9
PREVIOUS
4
NEXT
TOP MENU ENTER
RETURN
AUDIO
When you can’t switch the audio channel of a
bilingual programme
When the unit is connected with a digital audio device using
an optional optical cable and “DIGITAL AUDIO OUT” is set
to “DOLBY DIGITAL/PCM”, it is not possible to switch the
audio channel of a bilingual programme recorded on a
DVD-RAM or DVD-RW (VR mode) disc. (墌pg. 91) In this
case, perform the following steps using the remote control to
switch “DIGITAL AUDIO OUT” from “DOLBY DIGITAL/
PCM” to “PCM ONLY”.
APress SET UP to access the Main Menu screen.
BPress we to select “DVD SET UP”, then press ENTER.
CPress we to select “AUDIO OUTPUT”, then press
ENTER.
DPress rt to select “DIGITAL AUDIO OUT”, then press
ENTER.
EPress rt to select “PCM ONLY”, then press ENTER.
(墌pg. 93)
FPress SET UP to complete the setting.
GPress AUDIO to select the desired audio channel.
DR-M10EK_01.book Page 36 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
37
Filename [DR-M10EK_07Playback.fm]
Page 37 February 25, 2004 5:59 pm
Live Memory
Playback
This unit records pictures onto DVD-RAM discs, instead of video
tapes, then plays back the pictures recorded on the discs. This
makes it possible to achieve high-speed writing and read-out
that has not been possible with conventional VCRs, enabling
recording and playback simultaneously.
It is called “Live Memory Playback” to start playback of the
programme being recorded, with a time-lag between a recording
point and a playback point, as shown in the figure below.
Not only can this unit play back a programme previously
recorded while recording or timer recording another
programme, but the unit also allows you to play back from the
beginning of a programme while continuing to record the same
programme.
Recording/playback status display
Press DISPLAY. The current status is superimposed on the TV
screen.
Playback
(High-speed read-out)
Recording
(High-speed writing)
High-speed spin
Image figure of DVD-RAM disc
Current recording position
(Recording point)
Recording start point
Current playback point
(Live Memory Playback)
0 30 min. 1 hour
Playback
continues
Recording
continues
Currently elapsed recording time
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PA U S EREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
DISPLAY
Live Memory Playback status can
be checked by pressing DISPLAY
to display the bar meter on the
superimpose display.
Bar meter display
Superimpose display
DR-M10EK_01.book Page 37 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_07Playback.fm]
Masterpage:Left+
38
Page 38 February 27, 2004 3:08 pm
PLAYBACK OPERATIONS (cont.)
Overview of Live Memory Playback
You can play back a programme you are recording from the beginning while continuing to record or timer record onto a DVD-RAM
disc. This is called “Live Memory Playback”.
NOTES:
●Live Memory Playback cannot be performed for approximately
30 seconds after recording has started.
●Although high-speed search up to approximately 30 seconds
before the current recording point is possible during Live
Memory Playback, once the current recording point is
reached, the unit resumes normal playback and maintains a
delay of approximately 30 seconds so that recording and
playback can continue.
●When using Live Memory Playback during timer recording,
playback continues even after the end of the recording.
●When using Live Memory Playback during timer recording,
playback is automatically stopped just before recording starts,
and then recording starts when the time arrives for the next
timer-programme.
●It is impossible to perform ITR even if you press 7 during Live
Memory Playback. (墌pg. 54, “Instant Timer Recording
(ITR)”)
Press 8 to display the programme being recorded, then
perform ITR settings.
●Playback may be paused for a moment during Live Memory
Playback, which does not interfere with recording.
●Live Memory Playback cannot be performed while recording
the source from DV input.
●When LIVE CHECK is pressed to display the picture currently
being recorded, the picture size may not be correct.
(R
ecor
di
ng screen
)(Li
ve
M
emory
Pl
ay
b
ac
k
screen
)
To start Live Memory Playback,
press 4 to play back from the
beginning OR press to
reverse-skip a little
To stop Live Memory
Playback, press 8
Checking the
picture currently
being recorded
To display, press
LIVE CHECK
To clear, press
LIVE CHECK
Recording stops
To stop recording,
press 8
(Playback and Live Check screen)
Live Memory Playback
picture
Recording
picture
To stop Live Memory
Playback, press 8
Press NAVIGATION
to display Library
Database DVD Navi
menu, then choose a
programme to play
back (墌pg. 66).
Pressing LIVE
CHECK during
Live Memory
Playback allows
you to check the
picture currently
being recorded.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PA U S EREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
7
4
8
NAVIGATION
DISPLAY
LIVE CHECK
Press NAVIGATION
to display Library
Database DVD Navi
menu, then choose a
programme to play
back (墌pg. 64).
Pressing LIVE
CHECK during
Live Memory
Playback allows
you to check the
picture currently
being recorded.
DR-M10EK_07Playback.fm Page 38 Friday, February 27, 2004 3:10 PM
Masterpage:Right-No-Heading
39
Filename [DR-M10EK_07Playback.fm]
Page 39 March 16, 2004 2:17 pm
Display during Live Memory Playback
During recording, you can watch at your will what was previously recorded or is currently being recorded. It is possible to perform
freely normal playback operations (forward/reverse high-speed search and variable-speed search) within the range of the orange or
blue bar on the TV screen.
When Live Memory Playback reaches the point of 30 seconds before the current recording point by forward high-speed search or other
operations, the unit returns to normal playback.
The superimpose display appears by pressing ON SCREEN. (墌pg. 15)
The Live Check picture is displayed on the bottom right corner by pressing LIVE CHECK.
This unit displays the current recording/playback status by the bar meter.
(Example of bar meter display)
Live Memory Playback mark
Playback title number
Disc used
Bar meter (see below)
Title name
Playback counter
Recording title number
Recording counter display
(remaining/elapsed time)
Present time
Recording channel
Playback mark
Recording mode
Recording mark
Live Check picture
Recording mark
Station name
While stopped
During playback
While recording
Live Memory Playback
Live Memory Playback of
another programme
Recorded
Capacity of a disc
Not recorded
Total length of the programme being played back
Current playback position
Capacity of a disc
Remaining capacity when recording started
Recording start position
Current recording position
Current playback position
Current playback position
Recording start position
Blue (recorded part)
Orange (recording part)
Green (playing part)
Black (unrecorded or unplayed part)
Total length of the programme being played back
Current recording position
Capacity of a disc
Capacity of a disc
Current recording position
DR-M10EK_07Playback.fm Page 39 Tuesday, March 16, 2004 2:17 PM
Filename [DR-M10EK_07Playback.fm]
Masterpage:Left+
40
Page 40 February 25, 2004 5:59 pm
PLAYBACK OPERATIONS (cont.)
Buttons to be used during Live Memory Playback
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
e
3
2
9
6
5
w
LIVE CHECK
8
Available
buttons Functions
6
●Pressing once skips forward to the
beginning of the next chapter being played
back.
●Pressing down for 2 or more seconds during
playback advances playback at 5 times the
normal speed while pressed. Releasing the
button resumes normal playback.
Available only when paused
●Pressing down for 2 or more seconds
advances playback at 1/16 times the normal
speed.
2
●Pressing once skips back to the beginning
of the chapter being played back.
●Pressing down for 2 or more seconds during
playback reverses playback at 5 times the
normal speed while pressed. Releasing the
button resumes normal playback.
Available only when paused
●Pressing down for 2 or more seconds
reverses playback at 1/16 times the normal
speed.
5
●Each press of the button during playback
advances the playback speed in 4 steps for
forward direction.
Available only when paused
●Pressing once advances playback by 1/16
times the normal speed.
●Each press of the button during forward 1/
16 times slow-motion advances slow-
motion by 1/16 times, 1/4 times and 1/2
times the normal speed.
3
●Each press of the button during playback
advances the playback speed in 5 steps for
reverse direction.
Available only when paused
●Pressing once reverses playback by 1/16
times the normal speed.
●Each press of the button during reverse 1/16
times slow-motion reverses slow-motion by
1/16 times, 1/4 times and 1/2 times the
normal speed.
9Pressing once pauses playback (still picture
playback). Pressing repeatedly advances the
still picture frame by frame.
we Available only when paused
●Advances/reverses the still picture frame by
frame.
8
Stops Live Memory Playback to return to the
screen being recorded.
Then a resume point is stored.
Pressing 8 again stops recording.
Pressing once skips forward for approximately
30 seconds and resumes playback.
Pressing repeatedly skips forward
continuously as many times as pressed.
It is useful when skipping over unwanted
sections.
Pressing once skips back for approximately 7
seconds and resumes playback.
Pressing repeatedly skips back continuously
as many times as pressed.
It is useful when watching sports programmes,
etc.
LIVE CHECK
Pressing once displays the picture currently
being recorded and the one being played
back simultaneously.
Pressing successively clears the Live Check
window and displays only the picture
currently being played back.
You can check, for example, if the programme
you are recording has already finished.
DR-M10EK_01.book Page 40 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
41
Filename [DR-M10EK_07Playback.fm]
Page 41 February 25, 2004 5:59 pm
To play back from the beginning of the
programme while recording
You can play back a programme you are recording from the
beginning while continuing to record or timer record onto a
DVD-RAM disc.
1Start Live Memory Playback.
Press 4.
●Playback starts from the beginning of the programme being
recorded.
●Pressing 2/6 allows you to locate the desired scenes.
To move back the playback position
slightly while recording (One Touch
Replay function)
You can move back the playback position while continuing to
record or timer record onto a DVD-RAM disc.
1Start One Touch Replay function.
Press .
●Each press skips back for approximately 7 seconds and
resumes playback.
●Pressing while paused skips back for approximately 7 seconds
and resumes pause.
To watch a programme previously
recorded while recording
You can play back a programme you recorded previously while
recording.
1Start Live Memory Playback.
Press 4 while recording to establish Live Memory
Playback mode.
2Locate the beginning of the desired programme.
Press 2 or 6.
NOTE:
To stop playback, press 8. The programme being recorded is
displayed.
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
26
4
8
DVDTV
CABLE/SAT
DR-M10EK_01.book Page 41 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_07Playback.fm]
Masterpage:Left+
42
Page 42 February 25, 2004 5:59 pm
PLAYBACK OPERATIONS (cont.)
Using Play Set Up
Menu
Play Set Up Menu allows you to control various playback
functions. Some of the functions operated on Navigation Menu
can be controlled on Set Up Menu.
How to Access Play Set Up Menu
Press ON SCREEN twice whenever a disc is loaded.
Contents of Play Set Up Menu during playback
DVD VIDEO
Video CD/SVCD
JPEG disc
ADisc type.
BSelect this for Repeat Playback. (墌pg. 44)
CSelect this for A-B repeat Playback. (墌pg. 45)
DSelect this for search function. (墌pg. 45)
ESelect this for time search function. (墌pg. 46)
FSelect this to switch Simulated Surround Effect
function. (墌pg. 46)
GSelect this for Picture Control function. (墌pg. 47)
HSelect this to switch picture source type. (墌pg. 47)
ICurrent status area for the selected item.
JSelect this for Programme Playback. (墌pg. 48)
KSelect this for Random Playback. (墌pg. 48)
LSelect this to control the switching interval of the slide
show. (墌pg. 48)
NOTE:
Although examples of Play Set Up Menu are provided here only
for 3 types of discs, Play Set Up Menu will be displayed for
whichever disc indicated in the left column.
Before using Play Set Up Menu
Be sure to clear Library Database DVD Navi screen by
pressing NAVIGATION.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
NAVIGATION
ON SCREEN
DR-M10EK_01.book Page 42 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
43
Filename [DR-M10EK_07Playback.fm]
Page 43 February 25, 2004 5:59 pm
Basic operation on Play Set Up Menu
Example: When selecting Picture Control function of DVD
During playback or while stopped
1Access Play Set Up Menu.
Press ON SCREEN twice.
●The item currently selected is highlighted and pointed by H.
2Select the menu item.
Press we to select “ ”, then press ENTER.
●The pop-up window appears under the selected item.
3Select the option.
Press rt to select the desired option, then press ENTER.
To clear Play Set Up Menu
Press ON SCREEN.
NOTE:
See the corresponding pages for details on each menu item.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
rtwe
ENTER
ON SCREEN
DR-M10EK_01.book Page 43 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_07Playback.fm]
Masterpage:Left+
44
Page 44 February 25, 2004 5:59 pm
PLAYBACK OPERATIONS (cont.)
Repeat Playback
You can repeat playback as you like according to the type of
disc.
1Access Play Set Up Menu.
Press ON SCREEN twice.
2Select the menu item.
Press we to select “ ”, then press ENTER.
●The pop-up window appears under the selected item.
3Select the repeat mode.
Press rt repeatedly to select the desired Repeat mode,
then press ENTER.
DVD-RAM/RW/R
DVD VIDEO
Audio CD/Video CD/SVCD/JPEG/MP3
* “TRACK REPEAT” cannot be selected for JPEG discs.
To clear Play Set Up Menu
Press ON SCREEN.
To cancel Repeat Playback
Repeat the above procedure from step 1, select “OFF” in
step 3, then press ENTER.
NOTES:
●Repeat Playback is not possible for a Video CD/SVCD with
PBC function.
●Repeat Playback may not work properly depending on the
type of the disc being used.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
ON SCREEN
0 – 9
CLEAR
&
rtwe
ENTER
OFF:Repeat playback is not performed.
ALL REPEAT: The whole disc is played back
repeatedly.
TITLE REPEAT: The current title is played back
repeatedly.
OFF: Repeat playback is not performed.
TITLE REPEAT: The current title is played back
repeatedly.
CHAPTER REPEAT: The current chapter is played back
repeatedly.
OFF:Repeat playback is not performed.
ALL REPEAT:The whole disc is played back
repeatedly.
TRACK REPEAT*: The current track is played back
repeatedly.
DR-M10EK_01.book Page 44 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
45
Filename [DR-M10EK_07Playback.fm]
Page 45 February 25, 2004 5:59 pm
A-B Repeat Playback
You can repeat the desired part.
During playback
1Access Play Set Up Menu.
Press ON SCREEN twice.
2Select the menu item.
Press we to select “ ”.
3Locate the start point.
Press ENTER at the beginning of the desired part you
want to repeat (point A).
●The elapsed playing time of the point A appears
4Locate the end point and start A-B Repeat
Playback.
Press
ENTER
at the end of the desired part you want to
repeat (point B).
●The elapsed playing time of the point B appears.
●The selected part of the disc (between point A and B) is played
repeatedly.
To clear Play Set Up Menu
Press ON SCREEN.
To cancel A-B Repeat Playback
Press we to select “ ”, then press ENTER.
NOTES:
●A-B Repeat Playback may not work properly depending on the
type of disc being used.
●The subtitles recorded around the A-B point may not appear.
●When the end of the item is reached before the end point is
set, Play Set Up Menu disappears from the TV screen. In such
a case, repeat the procedure from step 1.
●The point B must be set at least 3 seconds after the point A.
●When playing back a DVD, A-B Repeat Playback is possible
only within the same title.
●“ ” cannot be selected during Programme and
Random Playback.
●“ ” cannot be selected while stopped.
Locating the beginning of a desired
selection
You can locate the beginning of a title, chapter, group or track.
During playback or while stopped
1Access Play Set Up Menu.
Press ON SCREEN twice.
2Select the menu item.
Press we to select “ ”, then press ENTER.
3Select the desired item.
For DVD-RAM/RW/R, DVD VIDEO
“TITLE SEARCH” or “CHAPTER SEARCH” is selectable.
(“TITLE SEARCH” only is selectable while stopped.)
For JPEG, MP3
“GROUP SEARCH” or “TRACK SEARCH” is selectable.
For Video CD/SVCD, Audio CD
“TRACK” is selectable.
Press rt to select the desired item, then press ENTER.
●Skip this step for Video CD/SVCD and Audio CD.
4Specify the number of the selected item.
Press number keys (1–9, 0) to enter the desired item
number, then press ENTER.
●Playback starts from the selected section.
If you have specified a wrong selection
Press & or CLEAR to clear the wrong number, then enter the
correct one before you press ENTER in this step.
To clear Play Set Up Menu
Press ON SCREEN.
NOTES:
●When “X” is displayed on the TV screen in step 4, the chapter
you have selected is not contained in the disc, or chapter
search does not work on the disc.
●Before you press ENTER, playback may start automatically
when you enter the section’s number depending on the disc.
●This function is not possible for a Video CD/SVCD with PBC
function.
Examples:
To select track 5, press the number key “5”.
To select track 15, press the number key “1” and “5”.
To select track 25, press number key “2”, then “5”.
DR-M10EK_01.book Page 45 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_07Playback.fm]
Masterpage:Left+
46
Page 46 February 25, 2004 5:59 pm
PLAYBACK OPERATIONS (cont.)
Time Search
You can play back a disc from the desired point by specifying the
elapsed playing time from the beginning of a title (DVD-RAM,
DVD-R, DVD-RW and DVD VIDEO) or a disc (Video CD/SVCD
and Audio CD).
1Access Play Set Up Menu.
Press ON SCREEN twice.
2Select the menu item.
Press we to select “ ”, then press ENTER.
●The pop-up window appears under the selected item.
3Enter the time.
Use number keys (1–9, 0) to enter the time, then press
ENTER.
●Playback starts from the specified time.
Example:
To play back from a point 12 (minutes): 50 (seconds) elapsed.
If you have specified a wrong selection,
Press & (for the last entered number) or 8 (for whole numbers)
to clear the wrong number, then enter the correct one(s) before
you press ENTER in this step.
To clear Play Set Up Menu
Press ON SCREEN.
NOTES:
●When “X” is displayed on the TV screen in step 3, you have
selected a point that excesses the recording time of the disc.
●Some DVD VIDEO discs do not contain time information, and
it is not possible to use the Time Search function. In such
cases, “X” is displayed on the TV screen as well.
●This function is not possible for a Video CD/SVCD with PBC
function.
Simulated Surround Effect
It is possible to get a simulated surround effect from your stereo
system. You can enjoy the virtual surround sound with your
2-channel stereo system.
1Access Play Set Up Menu.
Press ON SCREEN twice.
2Select the menu item.
Press we to select “ ”, then press ENTER.
●Above the selected item, “3D-ON” appears and Simulated
Surround Effect is activated.
●Each time you press ENTER, “3D-ON” appears and disappears
alternately.
To cancel the simulated surround effect
Press ENTER to clear “3D-ON” from the screen.
NOTES:
●The simulated surround effect works correctly only when
playing back a title recorded in multichannels.
●Simulated Surround Effect does not affect the DVD VIDEO
bitstream signal from the “DIGITAL AUDIO OUT” connector.
●When Simulated Surround Effect is activated, the settings of
“ANALOG AUDIO OUT” and “D. RANGE CONTROL” are
disabled. (墌pg. 93)
Press 1 Press 2
Press 0Press 5
DR-M10EK_01.book Page 46 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
47
Filename [DR-M10EK_07Playback.fm]
Page 47 February 25, 2004 5:59 pm
Adjusting the picture quality
You can obtain optimal picture quality by selecting an
appropriate picture mode.
1Access Play Set Up Menu.
Press ON SCREEN twice.
2Select the menu item.
Press we to select “ ”, then press ENTER.
●The pop-up window appears under the selected item.
3Select the desired option.
Press rt to select the desired option, then press ENTER.
Setting the progressive mode
You can obtain optimal picture quality by selecting whether the
content on the disc is processed by field (video source) or by
frame (film source).
1Access Play Set Up Menu.
Press ON SCREEN twice.
2Select the menu item.
Press we to select “ ”, then press ENTER.
●The pop-up window appears under the selected item.
3Select the desired option.
Press rt to select the desired option, then press ENTER.
NOTE:
When the progressive mode is set, be sure to set “L-1 OUTPUT”
to “COMPONENT”. (墌pg. 84, “L-1 Output and L-1 Input
Setting (L-1 OUTPUT and L-1 INPUT)”) Progressive scan is
output only from COMPONENT VIDEO OUT connector.
NORMAL: Normally select this option.
CINEMA: Suitable for a movie disc, etc.
SHARP: Clearer, sharper-edged picture when viewing
images with lots of flat, same-coloured surfaces
such as cartoons.
SOFT: Select this option when too much noise appears.
AUTO 1: Used to play a disc containing both video
and film source materials. This system
recognizes the source type (video or film) of
the current disc according to the disc
information. Normally select this option.
AUTO 2: Almost the same as the “AUTO 1”, but the
processing of the scenes with movement is
different. Select “AUTO 1” or “AUTO 2” to
your preference.
FILM: Suitable for playing back a progressive
scanned film source disc.
VIDEO: Suitable for playing back a video source disc.
The outlines on the played back pictures will
be soft.
DR-M10EK_01.book Page 47 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_07Playback.fm]
Masterpage:Left+
48
Page 48 February 25, 2004 5:59 pm
PLAYBACK OPERATIONS (cont.)
Programme Playback
You can play back up to 30 tracks in the desired order.
While stopped
1Access Play Set Up Menu.
Press ON SCREEN twice.
2Select the menu item.
Press we to select “PRGM”, then press ENTER.
●The programme table appears under Play Set Up Menu.
3Select the tracks in the desired order.
Use number keys (1–9, 0) to enter the track numbers.
If you have specified a wrong selection
Press &. The last selection is erased.
Or press 8. The whole selection is erased.
4Start playback.
Press 4. Playback starts in the programmed order.
●When all of the programmed tracks have been played back,
Programme Playback stops, but the programmed information
remains.
●To add tracks to the end of the programme, perform steps 1
through 3.
●During Programme Playback, pressing 6 skips to the next
selection of the programme. Pressing 2 returns to the
beginning of the current selection.
To clear Play Set Up Menu and the contents of the
programme from the screen
Press ON SCREEN.
To cancel Programme Playback
Press we to select “PRGM”, then press ENTER.
NOTE:
Programme Playback is not possible depending on the type of
disc.
Random Playback
You can play back all the tracks on the disc in random order.
While stopped
1Access Play Set Up Menu.
Press ON SCREEN twice.
2Select the menu item.
Press we to select “RND”, then press ENTER.
●Playback starts in random order.
To clear Play Set Up Menu and the contents of the
programme from the screen
Press ON SCREEN.
To cancel Random Playback
Perform steps 1 and 2.
NOTE:
The same track will not be played back more than once during
Random Playback.
Select the switching interval of the
slide show
You can control the switching interval of the slide show.
1Access Play Set Up Menu.
Press ON SCREEN twice.
2Select the menu item.
Press we to select “ ”, then press ENTER.
●The pop-up window appears under the selected item.
3Select the desired option.
Press rt to select the desired option, then press ENTER.
●Each time you press rt, the interval changes as follows:
5 SEC. { 10 SEC. { 15 SEC. { 20 SEC. { 25 SEC. {
30 SEC. { (Back to the beginning)
Examples:
●To select track 5, press the number key “5” and ENTER.
●To select track 15, press the number key “1” and “5”.
●To select track 25, press the number key “2” and “5”.
DR-M10EK_01.book Page 48 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
49
Filename [DR-M10EK_07Playback.fm]
Page 49 February 25, 2004 5:59 pm
Parental Lock
This function restricts playback of DVD VIDEO discs which
contain violent (and other) scenes according to the level set by
the user. For example, if a movie which includes violent scenes
supports the parental lock feature, such scenes which you do not
want to let children view can be cut or replaced by other scenes.
To set Parental Lock for the first time
While stopped
AAccess the “DVD SET UP” screen.
APress SET UP.
BPress we to select “DVD SET UP”, then press ENTER.
BAccess the “PARENTAL LOCK” screen.
CSelect the desired level.
DEnter your password.
ESelect your country code.
FEnter your password.
Press the number keys to enter the same password as in
step D above, then press ENTER.
GComplete the setting.
Press SET UP twice.
●The normal screen resumes.
NOTE:
Remember your password, or make a note of it.
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
rtwe
ENTER
SET UP
0 – 9
DVDTV
CABLE/SAT
APress we to select
“UTILITY”, then press
ENTER.
BPress rt to select
“PARENTAL LOCK”, then
press ENTER.
APress rt repeatedly to
select “PARENTAL
LEVEL”, then press ENTER.
BPress rt repeatedly to
select the desired level,
then press ENTER.
●The smaller the value of level
is, the more restrictive the
Parental Lock level becomes.
●Select “NONE” to cancel the
restriction.
Press the number keys to
enter your desired four-digit
number, then press ENTER.
●If you made a mistake, enter a
correct number again.
APress rt repeatedly to
select “COUNTRY
CODE”, then press
ENTER.
BPress rt repeatedly to
select your country code,
then press ENTER.
●If you do not need to change
your country code, jump to G.
●See “Country/Area Code List
for Parental Lock” (墌pg. 51).
DR-M10EK_01.book Page 49 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_07Playback.fm]
Masterpage:Left+
50
Page 50 February 25, 2004 5:59 pm
PLAYBACK OPERATIONS (cont.)
To change the settings
You can change the Parental lock settings later.
AChange the level.
APress rt repeatedly to select “PARENTAL LEVEL”,
then press ENTER.
BPress rt repeatedly to select the desired level, then
press ENTER.
BChange the country code.
APress rt repeatedly to select “COUNTRY CODE”,
then press ENTER.
BPress rt repeatedly to select your country code, then
press ENTER.
●See “Country/Area Code List for Parental Lock” (墌pg. 51).
CEnter your password.
Press the number keys to enter the same password as in
step D of “To set Parental Lock for the first time”, then
press ENTER.
DComplete the setting.
Press SET UP twice.
●The normal screen resumes.
NOTE:
If you forget your password, enter “8888” in step C.
To temporarily release Parental Lock
When you set the parental lock level strictly, some discs may not
be played back at all. When you insert such a disc and try to
play it back, the confirmation screen appears on the TV screen,
asking you whether you want Parental Lock to be temporarily
released or not.
AAccess the password screen.
APlace the disc on the disc tray.
●If the disc is rated higher than the selected level, the
confirmation screen appears.
BPress we to select “YES”, then press ENTER.
●If you select “NO”, you cannot play back that disc.
BEnter your password.
Press the number keys to enter the same password as in
step D of “To set Parental Lock for the first time”, then
press ENTER.
●When you enter the correct password, the Parental Lock is
released and the unit starts playback.
●If you enter a wrong password, “ENTRY ERROR RETRY”
appears on the TV screen. Enter the correct password.
●If you have successively entered wrong password three times,
“ENTRY ERROR CAN NOT CHANGE PASSWORD” appears
on the TV screen. In such a case, press ENTER. The disc will
stop. Then play the disc again, and try the procedure again
from step A.
NOTE:
If you forget your password, enter “8888” in step B.
Perform steps A to B of “To set Parental Lock for the first
time” on page 49 to access the “PARENTAL LOCK” screen
before continuing.
DR-M10EK_01.book Page 50 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
51
Filename [DR-M10EK_07Playback.fm]
Page 51 February 25, 2004 5:59 pm
Country/Area Code List for Parental Lock
AD
AE
AF
AG
AI
AL
AM
AN
AO
AQ
AR
AS
AT
AU
AW
AZ
BA
BB
BD
BE
BF
BG
BH
BI
BJ
BM
BN
BO
BR
BS
BT
BV
BW
BY
BZ
CA
CC
CF
CG
CH
CI
CK
CL
CM
CN
CO
CR
CU
CV
CX
CY
CZ
DE
DJ
DK
DM
DO
DZ
EC
EE
EG
EH
ER
Andorra
United Arab Emirates
Afghanistan
Antigua and Barbuda
Anguilla
Albania
Armenia
Netherlands Antilles
Angola
Antarctica
Argentina
American Samoa
Austria
Australia
Aruba
Azerbaijan
Bosnia and Herzegovina
Barbados
Bangladesh
Belgium
Burkina Faso
Bulgaria
Bahrain
Burundi
Benin
Bermuda
Brunei Darussalam
Bolivia
Brazil
Bahamas
Bhutan
Bouvet Island
Botswana
Belarus
Belize
Canada
Cocos (Keeling) Islands
Central African Republic
Congo
Switzerland
Côte d’Ivoire
Cook Islands
Chile
Cameroon
China
Colombia
Costa Rica
Cuba
Cape Verde
Christmas Island
Cyprus
Czech Republic
Germany
Djibouti
Denmark
Dominica
Dominican Republic
Algeria
Ecuador
Estonia
Egypt
Western Sahara
Eritrea
ES
ET
FI
FJ
FK
FM
FO
FR
FX
GA
GB
GD
GE
GF
GH
GI
GL
GM
GN
GP
GQ
GR
GS
GT
GU
GW
GY
HK
HM
HN
HR
HT
HU
ID
IE
IL
IN
IO
IQ
IR
IS
IT
JM
JO
JP
KE
KG
KH
KI
KM
KN
KP
KR
KW
KY
KZ
LA
LB
Spain
Ethiopia
Finland
Fiji
Falkland Islands (Malvinas)
Micronesia (Federated States of)
Faroe Islands
France
France, Metropolitan
Gabon
United Kingdom
Grenada
Georgia
French Guiana
Ghana
Gibraltar
Greenland
Gambia
Guinea
Guadeloupe
Equatorial Guinea
Greece
South Georgia and the South Sandwich Islands
Guatemala
Guam
Guinea-Bissau
Guyana
Hong Kong
Heard Island and McDonald Islands
Honduras
Croatia
Haiti
Hungary
Indonesia
Ireland
Israel
India
British Indian Ocean Territory
Iraq
Iran (Islamic Republic of)
Iceland
Italy
Jamaica
Jordan
Japan
Kenya
Kyrgyzstan
Cambodia
Kiribati
Comoros
Saint Kitts and Nevis
Korea, Democratic People’s Republic of
Korea, Republic of
Kuwait
Cayman Islands
Kazakhstan
Lao People’s Democratic Republic
Lebanon
DR-M10EK_01.book Page 51 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_07Playback.fm]
Masterpage:Left+
52
Page 52 February 25, 2004 5:59 pm
PLAYBACK OPERATIONS (cont.)
LC
LI
LK
LR
LS
LT
LU
LV
LY
MA
MC
MD
MG
MH
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
MW
MX
MY
MZ
NA
NC
NE
NF
NG
NI
NL
NO
NP
NR
NU
NZ
OM
PA
PE
PF
PG
PH
PK
PL
PM
PN
PR
PT
PW
PY
QA
RE
RO
RU
RW
Saint Lucia
Liechtenstein
Sri Lanka
Liberia
Lesotho
Lithuania
Luxembourg
Latvia
Libyan Arab Jamahiriya
Morocco
Monaco
Moldova, Republic of
Madagascar
Marshall Islands
Mali
Myanmar
Mongolia
Macau
Northern Mariana Islands
Martinique
Mauritania
Montserrat
Malta
Mauritius
Maldives
Malawi
Mexico
Malaysia
Mozambique
Namibia
New Caledonia
Niger
Norfolk Island
Nigeria
Nicaragua
Netherlands
Norway
Nepal
Nauru
Niue
New Zealand
Oman
Panama
Peru
French Polynesia
Papua New Guinea
Philippines
Pakistan
Poland
Saint Pierre and Miquelon
Pitcairn
Puerto Rico
Portugal
Palau
Paraguay
Qatar
Réunion
Romania
Russian Federation
Rwanda
SA
SB
SC
SD
SE
SG
SH
SI
SJ
SK
SL
SM
SN
SO
SR
ST
SV
SY
SZ
TC
TD
TF
TG
TH
TJ
TK
TM
TN
TO
TP
TR
TT
TV
TW
TZ
UA
UG
UM
US
UY
UZ
VA
VC
VE
VG
VI
VN
VU
WF
WS
YE
YT
YU
ZA
ZM
ZR
ZW
Saudi Arabia
Solomon Islands
Seychelles
Sudan
Sweden
Singapore
Saint Helena
Slovenia
Svalbard and Jan Mayen
Slovakia
Sierra Leone
San Marino
Senegal
Somalia
Suriname
Sao Tome and Principe
El Salvador
Syrian Arab Republic
Swaziland
Turks and Caicos Islands
Chad
French Southern Territories
Togo
Thailand
Tajikista n
Tokelau
Turkmenistan
Tunisia
Tonga
East Timor
Turkey
Trinidad and Tobago
Tuvalu
Taiwan, Province of China
Tanzania, United Republic of
Ukraine
Uganda
United States Minor Outlying Islands
United States
Uruguay
Uzbekistan
Vatican City State (Holy See)
Saint Vincent and the Grenadines
Venezuela
Virgin Islands (British)
Virgin Islands (U.S.)
Viet Nam
Vanuatu
Wallis and Futuna Islands
Samoa
Yeme n
Mayotte
Yu g o s l a v i a
South Africa
Zambia
Zaire
Zimbabwe
DR-M10EK_01.book Page 52 Friday, February 27, 2004 10:07 AM
Masterpage:Right0
53
Filename [DR-M10EK_08Recording.fm]
Page 53 February 27, 2004 9:47 am
RECORDING
Basic Recording
ALoad a disc.
APress x to open the disc tray.
BPlace a recordable disc on the disc tray.
●For details, refer to “Placing a Disc” (墌pg. 10).
CPress x to close the disc tray.
BChoose a programme.
Press PR +/– or the number keys to select the channel
you wish to record.
CSet the recording speed.
Press REC MODE repeatedly until the desired recording
speed appears.
●Each time you press REC MODE, the recording speed changes
as follows:
XP ] SP ] LP ] EP ] FR60–FR360*, FR420, FR480 ]
(Back to the beginning)
* The value is selectable from 1 to 6 hours in 5-min. increment by
pressing
we
repeatedly after selecting “FR60–FR360”. To change
the value in 30-min. increments, press and hold
we
.
●For details on the recording speed, see page 54.
DStart recording.
Press and hold 7, then press 4 on the remote control, or
press 7 on the unit.
EPause recording.
Press 9.
●To resume recording, press 4.
FStop recording.
Press 8.
It takes about 10 seconds to end the writing session when
you stop recording.
NOTES:
●It is recommended to format a DVD-RAM disc before use if
you use the disc on this unit for the first time.
●When using a brand-new DVD-RW disc, format the disc either
in VR mode or in Video mode. (墌pg. 106, “Format a
DVD-RW disc”)
●You can record up to 99 programmes and 999 play lists on
each disc.
●Some programmes can only be recorded one time.
●When recording is started, an index of the first part of
recording is automatically recorded (墌pg. 66, “Library
Database DVD Navi”). To record a satellite programmes, refer
to page 65. To delete the index, refer to page 71.
●Recording sometimes may stop or cannot be performed even if
there is enough available capacity remaining on the disc.
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
A
TTENTION:
It is not possible to record programmes on a DVD-R disc
which has already been finalised.
1
STANDBY/ON
S-VIDEO VIDEO
L(MONO)
-
AUDIO
-
R
DV
DV IN
F1
REC MODE
SAT#
VIDEO
PULL - OPEN
REC MODE4
x
798
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PA U S EREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
x
7
8
0 – 9
9
4
PR +/–
REC MODE
we
DVDTV
CABLE/SAT
Recording Resume Function
If there is a power outage during recording, Instant Timer
Recording (ITR) (墌pg. 54) or timer recording (墌pg. 56,
58), the recording will resume automatically when power is
restored to the unit unless the unit’s memory backup has
expired.
DR-M10EK_01.book Page 53 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_08Recording.fm]
Masterpage:Left+
54
Page 54 February 27, 2004 9:47 am
RECORDING (cont.)
Recording Features
Recording Speed
MPEG2 format is used as recording format. As a guide for picture
quality, the “bps” unit is used to represent how much data can
be recorded per second. The larger this value is, the better the
picture quality becomes but more capacity is required for the
recording. Select XP or SP for programmes where quick
movement occurs, such as sports programmes, and LP or EP for
talk shows, etc. with relatively less movement.
The recording speeds for a 4.7 GB disc are set as follows:
Instant Timer Recording (ITR)
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-min. increments), and shuts the unit off after
recording is finished.
1Start recording.
Press 7 on the unit.
2Engage the ITR mode.
Press 7 again. On the front display panel, “0:30”
appears.
3Set the recording duration.
If you want to record for more than 30 minutes, press 7
to extend the time. Each press extends recording time by
30 minutes.
NOTES:
●You can only perform ITR using the 7 button on the unit’s
front panel.
●If “DIRECT REC” is set to “ON” in the menu, Instant Timer
Recording (ITR) function does not work. (墌pg. 94)
Watch Another Programme While
Recording on the Unit
While recording is going on, you can watch another programme
on the TV by using the TV’s tuner. It is required that the remote
control is set to be able to operate the TV in advance.
(墌pg. 88, “TV Multi-Brand Remote Control”)
1Switch the TV to TV mode.
During recording, press TV AV/VIDEO to select TV
mode.
●Video mode is disengaged and the video indicator on the unit
is turned off.
●The programme received on the TV’s tuner is displayed on the
TV screen.
2Switch the remote control to TV control mode.
Slide the TV/CABLE/SAT/DVD switch to TV.
3Select the desired channel.
Press PR +/– repeatedly.
Elapsed Recording Time and Disc
Remaining Time Indication
During recording, press DISPLAY repeatedly until the
desired indication appears on the front display panel.
●Each time you press DISPLAY, the time indication changes as
follows:
Elapsed recording time ] Disc remaining time ] Clock ]
(Back to the beginning)
Recording
speed
Recording amount
(approx.)
Maximum recording
time (approx.)
XP 10 Mbps 1 hour
SP 5 Mbps 2 hours
LP 2 Mbps 4 hours
EP 1.6 Mbps 6 hours
FR60–FR360
(墌pg. 55)
The amount varies
depending on the
selected time.
1 – 6 hours
FR420 7 hours
FR480 8 hours
1
STANDBY/ON
S-VIDEO VIDEO
L(MONO)
-
AUDIO
-
R
DV
DV IN
F1
REC MODE
SAT#
VIDEO
PULL - OPEN
7
VIDE
O
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PA U S EREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
PR +/–
DISPLAY
TV AV/
VIDEO
DR-M10EK_01.book Page 54 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
55
Filename [DR-M10EK_08Recording.fm]
Page 55 February 27, 2004 9:47 am
Free Rate Function
To record the entire programme, the unit automatically set the
appropriate recording speed depending on the combination of
the total time of the programme to be recorded and either the
remaining disc space or the specified recording time (from 60
minutes to 480 minutes).
To record the entire programme within the actual
remaining disc space
Select “FR (JUST)” in a recording speed selection procedure.
(墌pg. 57, 59)
●Note that this function is available only for timer programming
recording.
To record the entire programme by specifying the
desired recording time
Select “FR60–FR360”, “FR420” or “FR480” in a recording speed
selection procedure. (墌pg. 53, 57, 59)
To record a 25-min. long daily programme five times just
on a same disc for example
Perform “VIDEO Plus+® Timer Programming” (墌pg. 56)
procedure. Be sure to set the recording speed to “FR125” and set
Weekly/Daily Rec Function to “MON–FRI” in step E to fit the
total recording time to the whole disc space.
When the same programme is recorded in SP mode instead of in
“FR125”, the 5th programme cannot be recorded.
NOTES:
●You can programme this unit to timer-record, regardless of the
disc remaining time. When the disc remaining time is not
enough, recording may stop in the middle of a programme. To
avoid this, make sure of the disc remaining time before setting
timer-programming.
(Example) If you programmed to timer-record for 60 minutes
in SP mode on a 120-minute disc, the disc remaining time
would be 30 minutes in XP mode, 60 minutes in SP mode,
120 minutes in LP mode, 180 minutes in EP mode, and 240
minutes in FR480 mode. Timer-recording will not complete
beyond these remaining times.
●The maximum recording time of FR (JUST) mode is the same
as the recording time of FR480 mode. When timer-
programming a long programme in FR (JUST) mode on a disc
whose remaining time is short, it is recommended checking
the disc remaining time in FR480 mode to see if the remaining
time is enough for the programme.
●Even if more than one programme are timer-programmed in
FR (JUST) mode, only the first one is recorded.
●In order to ensure that the recording fits on the disc, this
feature may leave a slight non-recorded section at the end of
the disc.
●There may be some noise and sound disturbance at the point
on the disc where the unit switches the mode.
Receiving Stereo and Bilingual
Programmes
Your unit is equipped with a Digital stereo sound decoder
(NICAM) making reception of stereo and bilingual broadcasts
possible.
When the channel is changed, the type of broadcast being
received will be displayed on the TV screen for a few seconds.
NOTES:
●“SUPERIMPOSE” must be set to “AUTO”. Otherwise the
on-screen displays will not appear. (墌pg. 95)
●If the quality of stereo sound being received is poor, the
broadcast might be received in monaural with better quality.
Selection of the audio channel to be
recorded on a disc
When a programme is recorded on a DVD-RAM or DVD-RW
disc in VR mode, all audio channels of the receiving programme
are recorded on the disc. When you record a programme on a
DVD-R or DVD-RW disc in video mode, select the desired audio
channel (from among “NICAM 1/MAIN”, “NICAM 2/SUB”,
“MONO”) to be recorded on the disc. (墌pg. 94)
NOTE:
Before playing back a programme recorded in stereo, or a
bilingual programme, refer to “Audio Channel Selection” on
page 36.
Blank
A:1st
B: 2nd
C:3rd
D:4th
E: 5th
A:1st
B: 2nd
C:3rd
D:4th
E: Blank
(20 min.)
Blank
Type of Broadcast Being
Received On-screen Display
Regular Monaural
NICAM Stereo
NICAM Bilingual
NICAM Monaural
DR-M10EK_01.book Page 55 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_08Recording.fm]
Masterpage:Left0
56
Page 56 February 27, 2004 9:47 am
TIMER RECORDING
VIDEO Plus+®
Timer
Programming
You can programme this unit to timer-record as many as
8 programmes.
With the VIDEO Plus+ system, timer programming is greatly
simplified because each TV programme has a corresponding
code number which your unit is able to recognize.
You can use the remote control to enter the PlusCode number.
ALoad a disc.
APress x to open the disc tray.
BPlace a recordable disc on the disc tray.
●For details, refer to “Placing a Disc” (墌pg. 10).
CPress x to close the disc tray.
BAccess the VIDEO Plus+ screen.
Press VIDEO Plus+.
CEnter the PlusCode number.
●To clear all entered numbers at a time, press 8.
●If the number you entered is invalid, “PLUSCODE NO. ERROR
CONFIRM PLUSCODE NO. THEN RETRY” appears on the TV
screen. Input a valid PlusCode number.
●If “GUIDE PROGRAMME IS NOT SET SELECT CHANNEL
YOU WANT TO RECORD” appears on the TV screen, set
Guide Program Numbers (墌pg. 97) manually.
●When “PROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMME” appears on the TV screen, you need to cancel
some of the reserved programmes. (墌pg. 63)
DCheck the programme data.
The PlusCode number you entered and the matching
timer-recording information are displayed on the TV
screen. Check if they are correct.
●To cancel this setting, press VIDEO Plus+ or RETURN.
Before performing the VIDEO Plus+ Timer
Programming:
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
●Make sure that the unit’s built-in clock is set
properly.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PA U S EREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
rtwe
ENTER
8
x
#
0 – 9
RETURN
VIDEO Plus+
&
Press the number keys to
enter the PlusCode number
of a programme you wish to
record, then press ENTER.
●If you have made a mistake,
press & and input the correct
number before you press
ENTER.
IMP
O
RTANT:
Make sure the channel position number you wish to record is
displayed; if not, see “VIDEO Plus+® System Setup” on
page 97 and set the Guide Program number correctly.
DR-M10EK_01.book Page 56 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
57
Filename [DR-M10EK_08Recording.fm]
Page 57 February 27, 2004 9:47 am
ESet the following recording options as
required.
APress we to select the desired option.
BPress rt to select the desired setting, then press
ENTER.
“REC MODE” (墌pg. 54, “Recording Speed”) (墌pg. 55,
“Free Rate Function”), “VPS/PDC” (墌pg. 59, “PDC
Recording”)*, “DAILY/WEEKLY” (in the right column,
“Daily/Weekly Rec Function” ), “NAME” (墌pg. 70,
“Modify Programme Name”), and “STOP” (To advance/
go back the stop time by 30 minutes, press and hold
rt).
* VPS (Video Programme System) recording is not currently
available in the U.K. and not possible with this unit.
FAccess the confirmation screen.
Press ENTER.
GComplete timer programming.
Press ENTER.
●To programme another timer, repeat steps B–G.
●If “PROGRAM OVERLAPPED” appears on the TV screen, see
“When programmes overlap each other” (墌pg. 64).
HEngage the unit’s timer mode.
Press # (TIMER). The unit turns off automatically and
“#” appears on the front display panel.
●To disengage the timer mode, press # (TIMER) again.
NOTES:
●There may be cases that VIDEO Plus+ programming timer
recording function prolongs the stop time of the programming.
●The beginning of a programme may not be recorded. Also, if
the 1st programme’s recording stop time and the 2nd
programme’s recording start time is the same, the ending of the
1st programme may not be recorded.
●VIDEO Plus+ Timer Programming is not possible on the discs
used exclusively for On-Disc Timer Programming.
●If the copy limited programme is received during
timer-recording, the unit enters Record Pause mode.
Recording starts again if it is switched to a recordable
broadcast during the time you programmed.
Daily/Weekly Rec Function
You can record programmes with one of the following weekly/
daily timer settings.
Satellite Receiver Users
To timer-record a satellite broadcast using the VIDEO Plus+
system:
APerform “Satellite Receiver Control Setting” on page 28.
BPerform “VIDEO Plus+® Timer Programming”. In step E,
you cannot set “VPS/PDC” to “ON”.
CLeave the satellite receiver’s power on.
WEEKLY Select to record a weekly programme.
MON–FRI Select to record a daily programme from
Monday through Friday.
MON–SAT Select to record a daily programme from
Monday through Saturday.
SUN–SAT Select to record a daily programme from
Sunday through Saturday.
DR-M10EK_01.book Page 57 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_08Recording.fm]
Masterpage:Left+
58
Page 58 February 27, 2004 9:47 am
TIMER RECORDING (cont.)
Manual Timer
Programming
You can programme this unit to timer-record as many as
8 programmes.
If you do not know the PlusCode number for the programme you
wish to record, use the following procedure to set your unit to
timer-record the programme.
ALoad a disc.
APress x to open the disc tray.
BPlace a recordable disc on the disc tray.
●For details, refer to “Placing a Disc” (墌pg. 10).
CPress x to close the disc tray.
BAccess Programme Check screen.
CAccess the programme screen.
DEnter the recording date.
Press rt repeatedly to set the desired date.
●The current date appears on the TV screen. The date you enter
appears in its place.
EEnter the recording start time.
Press we to select “START”, then press rt repeatedly
to set the desired start time.
●Each press of rt advances/goes back the start time in 1-min.
increments.
●To advance/go back the start time in 30-min. increments, press
and hold rt.
Before performing Manual Timer Programming:
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
●Make sure that the unit’s built-in clock is set
properly.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PA U S EREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
rtwe
ENTER
x
#
PROG/
CHECK
DVDTV
CABLE/SAT
Press PROG/CHECK.
●When “PROGRAMME FULL
DELETE UNWANTED TIMER
PROGRAMME” appears on
the TV screen, you need to
cancel some of the reserved
programmes. (墌pg. 63)
Press rt repeatedly to
select “NEW TIMER
PROGRAMME”, then press
ENTER.
DR-M10EK_01.book Page 58 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
59
Filename [DR-M10EK_08Recording.fm]
Page 59 February 27, 2004 9:47 am
FEnter the recording stop time.
Press we to select “STOP”, then press rt repeatedly to
set the desired stop time.
●Each press of rt advances/goes back the stop time in 1-min.
increments.
●To advance/go back the stop time in 30-min. increments, press
and hold rt.
GEnter the channel position.
Press we to select “TV PROG”, then press rt
repeatedly to select the desired channel.
HSet the other recording options as required.
Refer to step E in “VIDEO Plus+® Timer Programming”
(墌pg. 56).
IAccess the confirmation screen.
Press ENTER.
JComplete timer programming.
Press ENTER.
●To programme another timer, repeat steps B–J.
KEngage the unit’s timer mode.
Press # (TIMER). The unit turns off automatically and
“#” appears on the front display panel.
●To disengage the timer mode, press # (TIMER) again.
NOTES:
●The beginning of a programme may not be recorded. Also, if
the 1st programme’s recording stop time and the 2nd
programme’s recording start time is the same, the ending of the
1st programme may not be recorded.
●If the copy limited programme is received during timer-
recording, the unit enters Record Pause mode. Recording starts
again if it is switched to a recordable broadcast during the
time you programmed.
Satellite Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programming:
APerform “Satellite Receiver Control Setting” on page 28.
BPerform “Manual Timer Programming”. In step G, press
AUX to change “TV PROG” to “SAT”. Then press rt to
enter the channel position for the satellite broadcast. In
step H, you cannot set “VPS/PDC” to “ON”.
CLeave the satellite receiver’s power on.
PDC Recording
Now available from some TV stations, PDC (Programme
Delivery Control) is a service designed to assure safe,
accurate timer recording. With this system, special code
signals are transmitted together with the audio/video signals.
These code signals control your unit and have precedence
over the advertised times which you may have preset into the
timer. This means that your unit will start and stop recording
when the preset TV programmes actually start and end —
even if the broadcast time of a preset TV programme is
changed from what has been advertised. PDC is currently
available nationally on BBC1, BBC2, Ch.4 and Ch.5, except
from a few small relay transmitters. Ch.3 operates a PDC
service in some areas. All channels intend to offer this
service in due course. Check your TV programme listing
guide for latest information. If the channel you intend to
record does not offer a PDC service your unit will not start
recording if PDC has been selected. Be sure to set PDC to
“OFF” if PDC is not available on your selected channel.
(See step H on page 59.)
NOTES:
●When you use Manual Timer Programming, set the start
time (PDC time) exactly as advertised in the TV listing. A
different time than advertised will result in no recording.
●PDC recording is also possible when a satellite receiver or
a cable system is connected to L-2 IN/DECODER
connector on your unit.
●PDC recording is also possible via the L-1 IN/OUT
connector.
DR-M10EK_01.book Page 59 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_08Recording.fm]
Masterpage:Left+
60
Page 60 February 27, 2004 9:47 am
TIMER RECORDING (cont.)
On-Disc Timer
Programming
On-Disc Timer Programming is a function used with discs that
are especially intended for a specific programme. The disc is
then programmed for a programme you always watch every day
or every week. Since older programs are automatically
overwritten, a single DVD-RAM/RW (VR mode) disc can be used
without worrying about how much recording capacity remains.
(墌pg. 62, “How discs are overwritten”)
You can programme each disc to timer-record as many as
8 programmes.
To make the disc for On-Disc Timer
Programming
ALoad a disc.
APress x to open the disc tray.
BPlace a recordable disc on the disc tray.
●For details, refer to “Placing a Disc” (墌pg. 10).
CPress x to close the disc tray.
BAccess Programme Check screen.
Press PROG/CHECK.
CAccess the programme screen.
When On-Disc Timer Programming is made for the first
time on the disc
Press rt repeatedly to select “DISC TIMER PRGM”,
then press ENTER.
●When some programmes are recorded on the disc, a caution
message appears. In such a case, backup the programmes as
required, then format the disc before making On-Disc Timer
Programming. (墌pg. 106, “Format A Disc”)
When On-Disc Timer Programming has already been
made on the disc
Press rt repeatedly to select “NEW TIMER
PROGRAMME”, then press ENTER.
DEnter the recording date.
Press rt repeatedly to set the desired date.
●The current date appears on the TV screen. The date you enter
appears in its place.
EEnter the recording start time.
Press we to select “START”, then press rt repeatedly
to set the desired start time.
●Each press of rt advances/goes back the start time in 1-min.
increments.
●To advance/go back the start time in 30-min. increments, press
and hold rt.
Before performing On-Disc Timer Programming:
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
●
Make sure that the unit’s built-in clock is set properly.
A
TTENTION:
●On-Disc Timer Programming is possible only with the disc
for On-Disc Timer Programming.
●If data is recorded on a disc for On-Disc Timer
Programming using a unit from another manufacturer, On-
Disc Timer Programming may no longer function properly.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
rtwe
ENTER
DVD1
PROG/CHECK
x
DVDTV
CABLE/SAT
DR-M10EK_01.book Page 60 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
61
Filename [DR-M10EK_08Recording.fm]
Page 61 February 27, 2004 9:47 am
FEnter the recording stop time.
Press we to select “STOP”, then press rt repeatedly to
set the desired stop time.
●Each press of rt advances/goes back the stop time in 1-min.
increments.
●To advance/go back the stop time in 30-min. increments, press
and hold rt.
GEnter the channel position.
Press we to select “TV PROG”, then press rt
repeatedly to select the desired channel.
HSet “DAILY/WEEKLY” option.
Refer to step E in “VIDEO Plus+® Timer Programming”
(墌pg. 56).
●It is necessary to set “DAILY/WEEKLY” option for On-Disc
Timer Programming. (墌pg. 57, “Daily/Weekly Rec
Function”)
ISet the other recording options as required.
Refer to step E in “VIDEO Plus+® Timer Programming”
(墌pg. 56).
●You can select XP, SP, LP, EP or FR480 mode for “REC
MODE”. You cannot select FR (JUST), FR60–FR360 and
FR420.
JAccess the confirmation screen.
Press ENTER.
KComplete timer programming.
Press ENTER.
●To programme another timer, repeat steps B–K.
To timer-record the programme with
the programmed disc
ALoad the disc.
APress x to open the disc tray.
BPlace the programmed disc on the disc tray.
●For details, refer to “Placing a Disc” (墌pg. 10).
CPress x to close the disc tray.
BEngage the unit’s timer mode.
Press DVD 1. The unit turns off and “ ” appears
on the front display panel.
●To disengage the timer mode, press DVD 1 again.
NOTES:
●Even if On-Disc Timer Programming is overlapping with other
timer programming, any caution message does not appear. In
such a case, recording will be executed in the descending
order of the recording start time of the programme.
●On-Disc Timer Programming is not possible on a DVD-RW
disc formatted in video mode. (墌pg. 106, “Format a
DVD-RW disc”)
●The information of a programme recorded with On-Disc Timer
Programming is not stored in the library. (墌pg. 76)
●The play list is not created for the programmes recorded with
On-Disc Timer Programming. (墌pg. 72)
●VIDEO Plus+ Timer Programming is not possible on the discs
used exclusively for On-Disc Timer Programming.
●Manual Timer Programming is not possible on the On-Disc
Timer Programmed disc. (墌pg. 58)
●Basic Recording is not possible on the On-Disc Timer
Programmed disc. (墌pg. 53)
●The On-Disc Timer Programming function does not work on
the unit form other manufactures even if the On-Disc Timer
Programmed disc is loaded.
●The beginning of a programme may not be recorded. Also, if
the 1st programme’s recording stop time and the 2nd
programme’s recording start time is the same, the ending of the
1st programme may not be recorded.
●If there is a power cut while recording, the recordings before
the power cut are not guaranteed.
Satellite Receiver Users
To timer-record a satellite broadcast using the On-Disc Timer
Programming function:
APerform “Satellite Receiver Control Setting” on page 28.
BPerform “On-Disc Timer Programming”. In step I, you
cannot set “VPS/PDC” to “ON”.
CLeave the satellite receiver’s power on.
DR-M10EK_01.book Page 61 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_08Recording.fm]
Masterpage:Left+
62
Page 62 February 27, 2004 5:53 pm
TIMER RECORDING (cont.)
How discs are overwritten
NOTES:
●On-Disc Timer Programming may not always work as these examples.
●On-Disc Timer Programming may not complete successfully if the recording stop time is extended due to PDC.
(Example 1)
To record a 1-hour serial drama every Friday in SP mode
(Example 2)
To record a 15-minute serial drama every morning in XP mode
(Example 3)
To record a 90-minute serial drama every Sunday in SP mode
The first programme is
overwritten by the third.
The second programme
is overwritten by the
forth.
Overwritten
Blank
Overwritten
1st 2nd 1st 2nd 3rd 4th 3rd
1st
2nd3rd
4th 5th
6th7th
8th
Areas treated as blank cannot be played back even if they
contain recorded material.
Blank
Blank Blank
1st
2nd 3rd
DR-M10EK_08Recording.fm Page 62 Friday, February 27, 2004 5:53 PM
Masterpage:Right-No-Heading
63
Filename [DR-M10EK_08Recording.fm]
Page 63 February 27, 2004 9:47 am
Check, cancel and change programmes
ADisengage the timer mode.
When “#” lights on the front display panel
Press # (TIMER), then press DVD 1.
When “ ” lights on the front display panel
Press DVD 1.
When “SAT#” lights on the front display panel
Press SAT#, then press DVD 1.
BAccess Programme Check screen.
CAccess the programme screen.
Press rt to select the programme, then press ENTER.
DChange a programme.
Change the settings of the desired recording options as
required.
●Refer to steps D–I in “Manual Timer Programming”
(墌pg. 58).
EComplete timer correction.
Press PROG/CHECK.
●The previous screen resumes.
FEngage the unit’s timer mode.
For VIDEO Plus+ or Manual Timer Programming
Press # (TIMER).
For On-Disc Timer Programming
Press DVD 1.
For Automatic Satellite Programme recording
Press SAT# for 2 seconds or more.
Press PROG/CHECK.
●To return to the previous
screen after you check the
programme, press PROG/
CHECK again.
To cancel the programme
Press rt repeatedly to
select a programme to be
cancelled, then press &.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
&
DVD 1
PROG/CHECK
SAT#
rtwe
ENTER
Programme’s information on the front display panel
You can check the details of the programmes even when the
power is turned off. (It is necessary that the Power Save mode
(墌pg. 95, “POWER SAVE”) is disengaged or the unit is not
in timer standby mode.) However, it is not possible to cancel
or change the programme’s setting.
APress PROG/CHECK.
●“NEW PROG” or “P-1” (if 8 programmes have already
been set) appears.
BPress rt repeatedly until the desired programme
number (“P-1” to “P-8”) appears, then press ENTER.
CPress e.
●Each time you press e, the indication changes as follows
(the settings in parentheses are examples):
Date (“DATE 08.03SU”) ] Start time (“ON 11:00”) ] Stop
time (“OFF 11:30”) ] Channel (“PR 1”) ] Weekly/Daily
(“MO-FR DAILY”) ] Programme number (“P-1”) and
Recording speed (SP) ] (Back to the beginning)
DPress PROG/CHECK to complete checking.
●The normal display resumes.
DR-M10EK_01.book Page 63 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_08Recording.fm]
Masterpage:Left+
64
Page 64 February 27, 2004 9:47 am
TIMER RECORDING (cont.)
When programmes overlap each other
If “PROGRAM OVERLAPPED” appears, you have another
programme overlapping the programme you have just made.
Confirm with the arrow on “OK”, then press PROG/CHECK.
Programme Check screen appears and conflicting programmes
will be highlighted in pink.
Example: Programme 3 (you have just made) and
Programme 4 overlap each other.
AConfirm the overlapping programmes.
Overlapping programmes appear on the TV screen.
NOTE:
If you do not mind this overlap, press PROG/CHECK to finish
the timer programme setting. The programme with the lower
programme number will be recorded and the other one will not
be recorded correctly. If no changes are made for approximately
1 minute, the unit will return to the normal screen.
BSelect the desired programme to be cancelled
or changed.
Press rt.
To cancel the programme
Press &.
●“THE TIMER PROGRAMMING SETTING WAS CANCELLED”
appears on the TV screen for about 5 seconds, then the normal
screen resumes.
To change the programme setting
Press ENTER.
CChange the programme setting.
●Refer to steps D–J in “Manual Timer Programming”
(墌pg. 58).
DCheck if the conflict has been settled.
Press PROG/CHECK.
●Programme check screen appears.
EEngage the unit’s timer mode.
●Refer to step F in “Check, cancel and change programmes”
(墌pg. 63).
NOTE:
When any overlaps remain after deletion and modification of
programmes, Programme Check screen remains showing the
conflicting programmes. In such a case, repeat the procedure
above until the conflict is solved.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PA U S EREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
PROG/CHECK
rt
ENTER
&
DR-M10EK_01.book Page 64 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
65
Filename [DR-M10EK_08Recording.fm]
Page 65 February 27, 2004 9:47 am
Automatic Satellite
Programme
Recording
This function allows you to automatically record a
satellite programme which is timer-programmed on your
external satellite receiver. Connect a satellite receiver to
the unit’s L-2 IN/DECODER connector and programme
the timer on the satellite receiver. When the signals come
into the unit from the satellite receiver, the unit
automatically turns on and starts recording. ASelect the L-2 SELECT mode.
Set “L-2 SELECT” to “SAT VIDEO” or “SAT S-VIDEO”
(墌pg. 85, “L-2 Select Setting (L-2 SELECT)”).
●Also refer to “IMPORTANT” on page 90.
BSet the recording speed.
Press REC MODE.
CEngage the Automatic Satellite Programme
Recording mode.
Press and hold SAT# for about 2 seconds. “SAT#”
appears on the front display panel and the unit turns off
automatically.
NOTES:
●To disengage the Automatic Satellite Programme Recording mode, press SAT#.
●If the unit’s power is off, it is not possible to engage the Automatic Satellite Programme Recording mode.
●In step C, if “SAT#” blinks quickly on the front display panel even though your satellite receiver’s power is off, Automatic Satellite
Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Manual Timer Programming”
(墌pg. 58) to timer-record a satellite programme.
* Some satellite receivers output signals even if the power is off. Automatic Satellite Programme Recording is not possible with those satellite receivers.
●“SAT#” blinks on the front display panel while Automatic Satellite Programme Recording is in progress.
●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.
●Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer.
●Pressing the unit’s 1 button while Automatic Satellite Programme Recording is in progress turns off the unit’s power and disengages
the Automatic Satellite Programme Recording mode.
●If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Recording, it is not possible
to set different recording speeds for each programme.
●Depending on the type of satellite receiver, the unit may not record a slight portion of the beginning of the programme or may record
slightly longer than the actual length of the programme.
●If you engage the Automatic Satellite Programme Recording mode when the satellite receiver’s power is on, the unit will not start
Automatic Satellite Programme Recording even though “SAT#” blinks on the front display panel. When the satellite receiver shuts
off once and is turned back on again, the unit starts recording.
●You can also record a programme from your cable system in the same way if the system has a timer.
●Just Clock (墌pg. 104) does not work when the Automatic Satellite Programme Recording mode is engaged.
●When the Automatic Satellite Programme Recording mode is engaged, or the unit’s power is turned off after Automatic Satellite
Programme Recording is finished, the unit will not enter the Timer mode even though “AUTO TIMER” is set to “ON” (墌pg. 96).
1
STANDBY/ON
S-VIDEO VIDEO
L(MONO)
-
AUDIO
-
R
DV
DV IN
F1
REC MODE
SAT
#
VIDEO
PULL - OPEN
REC MODE
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
SAT
#
SHOW VIEW/
VIDEO Plus
+SAT#
REC MODE
A
TTENTION:
●Be sure not to turn on the satellite receiver before the
programme is executed; otherwise, the unit will start
recording when the satellite receiver’s power is turned on.
●If you have connected another appliance other than a
satellite receiver to the L-2 IN/DECODER connector, be
sure not to engage the Automatic Satellite Programme
Recording mode; otherwise, the unit will start recording
when the connected appliance’s power is turned on.
●Automatic Satellite Programme Recording and
timer-recording cannot be done at the same time.
Before performing the following steps:
●Make sure the satellite receiver is connected to the unit’s L-2
IN/DECODER connector. (墌pg. 90)
●Programme the timer on the satellite receiver.
●Slide the TV/CABLE/SAT/DVD switch to TV.
DR-M10EK_01.book Page 65 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_09Navigation.fm]
Masterpage:Left0
66
Page 66 February 25, 2004 5:59 pm
NAVIGATION
Library Database
DVD Navi
The Library Database DVD Navi enables you to search and
select the desired programmes recorded on a DVD-RAM/R/RW
disc very easily.
You can record up to 99 programmes on a disc.
Each time a programme is recorded on the disc, the information
of the programme is registered for the Library Database DVD
Navi automatically.
So, you can confirm the information of the programmes
recorded on the disc with the Library Database DVD Navi
screen. And, you can also select one of the programmes
recorded on the disc using the Library Database DVD Navi.
The following screen appears as the Library Database DVD Navi screen when you press NAVIGATION. You can move the arrow to
select the desired position on the screen by pressing rt w e on the remote control.
The Icons and their meanings
AIndex
(Small still picture of each programme)
BNames of functions
ORIGINAL (墌pg. 69)
PLAY LIST (墌pg. 72)
LIBRARY (墌pg. 76)
CRemaining time
(Based on the recording speed currently selected)
DCurrent/Total number of programme(s)
(For example, there are 6 recorded programmes and the
programme indicated by the arrow is the 3rd one.)
EIcons
(Indicate the recording situation for each programme.)
FRecording information for the programme indicated by
the arrow
GGuidance for operations
HOperational commands
This programme is write-protected.
This programme has stereo sounds.
This programme has bilingual sounds.
This programme was recorded with timer
recording.
DR-M10EK_01.book Page 66 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
67
Filename [DR-M10EK_09Navigation.fm]
Page 67 February 25, 2004 5:59 pm
Using Library Database DVD Navi system, you can easily
modify registered information, edit the programme or play list,
as well as search for the beginning of each programme.
About registration of information
The following information is automatically registered for each
programme when ordinary recording or timer recording is
performed, then stored in an area specified on the unit.
●index* (reduced still pictures to show programme titles)
●programme title*
●category*
●date and time
●channel
●recording speed
●length of recording time
The items marked with an asterisk (*) can be easily modified and
registered again after recording by using Library Database DVD
Navi system.
About editing of programmes
Library Database DVD Navi system has the following functions
for editing of programmes.
●“Modify Original Information” (墌pg. 69)
●“Delete programme” (墌pg. 71)
The limitations of registration
You can register information up to 99 programmes.
When the amount of information is at the limits of registration,
you cannot record new programme any more. In this case, you
need to delete old programmes to register new one. (墌pg. 71,
“Delete programme”)
NOTE:
Once a DVD-R/RW (Video mode) disc has been finalized, the
displays for original and play list do not appear. Only display for
library appears.
The display for original recording
The display for play list
The display for library
DR-M10EK_01.book Page 67 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_09Navigation.fm]
Masterpage:Left+
68
Page 68 February 25, 2004 5:59 pm
NAVIGATION (cont.)
Scan for Beginning(s) of Programme(s) You can scan the beginning of the programme easily with the
Library Database DVD Navi.
ATurn on the unit.
Press DVD 1.
BLoad a disc.
APress x to open the disc tray.
BPlace a recorded disc on the disc tray.
●For details, refer to “Placing a Disc” (墌pg. 10).
CPress x to close the disc tray.
CAccess the Index screen.
DSelect the programme(s).
Press we to move the arrow on the index (small still
pictures) of the desired programme.
●When you want the plural
programmes to be played
back continuously, press
MEMO after selecting the
desired programme. The
numbers of the playback
order appear on the index.
You can select up to 30
programmes.
●When you want to correct the order, move the arrow on the
desired index and press MEMO. The number disappears and
the unit re-numbers the other programmes automatically.
●When you want to cancel the order, press CLEAR.
EStart playback.
Press ENTER. Or simply press SELECT. The playback
starts.
FPause playback.
Press 9.
●To resume normal playback, press 4.
GStop playback.
Press 8.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PA U S EREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
rtwe
ENTER
8
CLEAR x
DVD 1
NAVIGATION
9
4
SELECT
MEMO
DVDTV
CABLE/SAT
APress NAVIGATION. The
Library Database DVD
Navi screen appears.
BPress rt w e to move
the arrow to “ORIGINAL”,
then press ENTER.
DR-M10EK_01.book Page 68 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
69
Filename [DR-M10EK_09Navigation.fm]
Page 69 February 25, 2004 5:59 pm
Modify Original
Information
Modify Index
ATurn on the unit.
Press DVD 1.
BAccess the Index screen.
APress NAVIGATION. The Library Database DVD Navi
screen appears.
BPress rt w e to move the arrow to “ORIGINAL”,
then press ENTER.
CSelect a programme.
Press rt w e to move the arrow to select one
programme you want to modify, then press t.
DAccess the modify screen.
APress rt w e to move the arrow to “MODIFY”, then
press ENTER.
BPress we to move the arrow to “MODIFY INDEX”.
The “MODIFY INDEX” screen appears.
ERegister new index.
BConfirm the arrow is on “REPLACE”, then press ENTER
to register new index. New index appears on the right
window.
●When you press ENTER with the arrow on “RETURN” you can
return to the previous screen.
FReturn to the normal screen.
Press NAVIGATION.
●Press 8 to cancel pause mode after pressing NAVIGATION.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%DVD 1
rtwe
ENTER
8
9
5
3
NAVIGATION
4
DVDTV
CABLE/SAT
ASearch for the picture
from the programme by
pressing the appropriate
buttons (3, 4, 5, or
9). The pictures of the
programme appear on the
left window.
DR-M10EK_01.book Page 69 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_09Navigation.fm]
Masterpage:Left+
70
Page 70 February 25, 2004 5:59 pm
NAVIGATION (cont.)
Modify Programme Name
AAccess the modify screen.
APress rt w e to move the arrow to “MODIFY”, then
press ENTER.
BPress we to move the arrow to “MODIFY NAME”.
The “MODIFY NAME” screen appears.
BEnter new name.
●To correct a letter, press rt w e to move the arrow to
“DELETE” or “DELETE ALL”, then press ENTER.
●You can enter the letters up to 64.
●You can also enter the new name with number keys. For
example, when you press 2 repeatedly, “A”, “B”, “C”, “a”, “b”,
“c”, “2”, and then “A” appear by turns. You can use the
following buttons.
CRegister new name.
Press rt w e to move the arrow to “UPDATE”, then
press ENTER.
DReturn to the Library Database DVD Navi
screen.
Press rt w e to move the arrow to “RETURN”, then
press ENTER. The Library Database DVD Navi screen
appears again.
EReturn to the normal screen.
Press NAVIGATION.
Modify Category
AAccess the modify screen.
APress rt w e to move the arrow to “MODIFY”, then
press ENTER.
BPress we to move the arrow to “MODIFY
CATEGORY”. The “MODIFY CATEGORY” screen
appears.
BSelect new category.
CRegister new category.
Press ENTER. The Library Database DVD Navi screen
appears again.
DReturn to the normal screen.
Press NAVIGATION.
Protect title
You can protect the programme to prevent accidental erasure of
the important programme.
ASelect a programme.
Press rt w e to move the arrow to a programme you
want to protect, then press t.
BProtect the programme.
Press we to move the arrow to “PROTECT”, then press
ENTER.
●“ ” appears.
●To cancel the protection, repeat A–B again.
CReturn to the normal screen.
Press NAVIGATION.
NOTE:
All the programmes on a disc will be deleted once the disc is
formatted even if they are protected titles. (墌pg. 106)
Perform steps A to C of “Modify Index” (墌pg. 69) before
continuing.
Press rt w e to move the
arrow to the desired letter or
command, then press
ENTER. Repeat this process
to complete the name.
Number keys: for entering letters, numbers and blank
space
we buttons: for moving the entering or inserting point
8 button: for correcting a letter
2/6 buttons: for changing character tables
Perform steps A to C of “Modify Index” (墌pg. 69) before
continuing.
Press rt w e to move the
arrow to the desired category,
then press ENTER.
Perform steps A to B of “Modify Index” (墌pg. 69) before
continuing.
DR-M10EK_01.book Page 70 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
71
Filename [DR-M10EK_09Navigation.fm]
Page 71 February 25, 2004 5:59 pm
Delete programme
You cannot record any more with Library Database DVD Navi
once the registered programmes on the disc reach 99
programmes. Deleting unnecessary programmes after dubbing
(墌pg. 83, “Edit To Or From Another Recorder”) or other
operations can increase remaining time and available recording
capacity. (For DVD-R discs, although it is possible to delete
recorded programmes, available recording capacity does not
increase.) The deleted programme is never resumed. Play lists
and programme information in the unit’s library are also deleted.
ASelect a programme.
Press we to move the arrow to select one programme
you want to delete, then press t.
BAccess the delete screen.
Press rt w e to move the arrow to “DELETE”, then
press ENTER. The message appears for your confirmation.
CConfirm the deletion.
Press we to select “YES”, then press ENTER.
●When you cancel the deletion, select “NO”, then press
ENTER.
DReturn to the normal screen.
Press NAVIGATION.
Delete unwanted part of the
programme
You can delete unwanted part of the programme.
ASelect a programme.
Press we to move the arrow to select one programme
whose unwanted part you want to delete, then press t.
BAccess the delete screen.
Press we to move the arrow to “EDITING”, then press
ENTER.
CStart playback.
Press 4 to start playback. The playback pictures appear
in the window on the screen. The elapsed playing time
starts counting with the arrow on “IN”.
DSet edit-in and edit-out points.
BFind the point where you want the deletion to end,
then press ENTER with the arrow on “OUT”. The edit-
out time is fixed.
●Press 3, 4, 5, 2, 6 or 9 to find the edit-in and
edit-out points.
EConfirm the deletion.
APress rt w e to move the arrow to “PREVIEW”, then
press ENTER to preview the edited programme.
BPress rt w e to select “EXECUTE”, then press
ENTER.
●If you do not want to delete the scene, select “CLEAR” and
press ENTER.
CPress we to select “YES”, then press ENTER.
●The selected scene is deleted.
●To cancel the deletion, press we to select “NO”, then press
ENTER.
To modify the points
APress we to move the arrow to “CLEAR”, then press
ENTER.
BRepeat step C–E.
FReturn to the normal screen.
Press NAVIGATION.
NOTES:
●There may be a discrepancy of several seconds between the
scene you intend to edit, and the scene which is actually
edited.
●Available recording capacity may not match the deleted part
after deletion.
Perform steps A to B of “Modify Index” (墌pg. 69) before
continuing.
Perform steps A to B of “Modify Index” (墌pg. 69) before
continuing.
AFind the point where you
want the deletion to
begin, then press ENTER
with the arrow on “IN”.
The edit-in time is fixed
and the elapsed playing
time starts counting again.
DR-M10EK_01.book Page 71 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_09Navigation.fm]
Masterpage:Left+
72
Page 72 February 25, 2004 5:59 pm
NAVIGATION (cont.)
Modify Play List
Information
8Play List
It is a collection of the scenes. A play list can be freely edited
and played back without ever changing any original recording
data.
Using the random access of a DVD disc (which allows video
data to be instantly read no matter where it is on the disc), a play
list includes information such as the timer counter for the
playback start point and end point, indexes for checking the
contents of recorded data, category information, and more.
Playback according to a play list you have created allows you to
enjoy various combinations of video images from a single
programme.
Create Play List
ATurn on the unit.
Press DVD 1.
BLoad a disc.
APress x to open the disc tray.
BPlace a DVD-RAM or DVD-RW (VR mode) disc that
was recorded with this unit on the disc tray.
●For details, refer to “Placing a Disc” (墌pg. 10).
CPress x to close the disc tray.
CAccess the Play List screen.
APress NAVIGATION. The Library Database DVD Navi
screen appears.
BPress rt w e to move the arrow to “PLAY LIST”,
then press t or ENTER.
DCreate a play list.
Press rt w e to move the arrow to “CREATE”, then
press ENTER.
EStart playback.
Press 4 to start playback. The playback pictures appear
in the window on the screen. The elapsed playing time
starts counting with the arrow on “IN”.
●To locate the beginning of other titles, press 2/6.
FSet edit-in and edit-out points.
BFind the point where you want the created play list to
end, then press ENTER with the arrow on “OUT”. The
edit-out time is fixed.
●Press 3, 4, 5, 2, 6 or 9 to find the edit-in and
edit-out points.
●The edit-out point must come after the edit-in point.
GConfirm the play list.
APress we to move the arrow to “PREVIEW”, then
press ENTER to preview the play list.
BPress we to select “EXECUTE”, then press ENTER.
●The play list is created.
To modify the points
APress we to move the arrow to “CLEAR”, then press
ENTER.
BRepeat step E–G.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%DVD 1
rtwe
ENTER
3
9
4
5
2
NAVIGATION
x
6
DVDTV
CABLE/SAT
AFind the point where you
want the created play list
to begin, then press
ENTER with the arrow on
“IN”. The edit-in time is
fixed and the elapsed
playing time starts
counting again.
DR-M10EK_01.book Page 72 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
73
Filename [DR-M10EK_09Navigation.fm]
Page 73 February 25, 2004 5:59 pm
HReturn to the normal screen.
Press NAVIGATION.
NOTES:
●There may be a discrepancy of several seconds between the
scene you intend to edit, and the scene which is actually
edited.
●The title, index and category of the play list can be modified in
the same way as “ORIGINAL”. (墌pg. 69, “Modify Original
Information”)
●You can modify the play list that has just been created here by
adding, moving, or deleting unwanted parts to create a digest
edition, etc.
Add scenes to a play list
ASelect a play list.
Press we to move the arrow to the play list to which you
wish to add a scene, then press t.
BAccess the Editing screen.
CStart playback.
Press 4 to start playback. The playback pictures appear
in the window on the screen. The elapsed playing time
starts counting with the arrow on “IN”.
●To locate the beginning of other titles, press 2/6.
DSet edit-in and edit-out points.
AFind the point where you want the added scene to
begin, then press ENTER with the arrow on “IN”. The
edit-in time is fixed and the elapsed playing time starts
counting again.
BFind the point where you want the added scene to
end, then press ENTER with the arrow on “OUT”. The
edit-out time is fixed.
●Press 3, 4, 5, 2, 6 or 9 to find the edit-in and
edit-out points.
EConfirm the addition.
APress we to move the arrow to “PREVIEW”, then
press ENTER to preview approximately 5 seconds
before and after the edited scene.
BPress we to select “EXECUTE”, then press ENTER.
●The selected scene is added.
To modify the points
APress we to move the arrow to “CLEAR”, then press
ENTER.
BRepeat step C–E.
FReturn to the normal screen.
Press NAVIGATION.
NOTE:
There may be a discrepancy of several seconds between the
scene you intend to edit, and the scene which is actually edited.
Move scenes
ASelect a play list.
Press we to move the arrow to a play list into which you
wish to move a scene, then press t.
BAccess the Editing screen.
CStart playback.
Press 4 to start playback. The playback pictures appear
in the window on the screen. The elapsed playing time
starts counting with the arrow on “IN”.
●To locate the beginning of other titles, press 2/6.
Perform steps A to C of “Create Play List” (墌pg. 72) before
continuing.
APress we to move the
arrow to “EDITING”, then
press ENTER.
BPress we to move the
arrow to “ADD SCENE”.
Perform steps A to C of “Create Play List” (墌pg. 72) before
continuing.
APress we to move the
arrow to “EDITING”, then
press ENTER.
BPress we to move the
arrow to “MOVE SCENE”.
DR-M10EK_01.book Page 73 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_09Navigation.fm]
Masterpage:Left+
74
Page 74 February 25, 2004 5:59 pm
NAVIGATION (cont.)
DSet edit-in and edit-out points.
AFind the point where you want the moved scene to
begin, then press ENTER with the arrow on “IN”. The
edit-in time is fixed and the elapsed playing time starts
counting again.
BFind the point where you want the moved scene to
end, then press ENTER with the arrow on “OUT”. The
edit-out time is fixed.
CPress 4 to start playback.
DFind the point where you want the moved scene to be
moved, then press ENTER with the arrow on “MOVE
TO”.
●Press 3, 4, 5, 2, 6 or 9 to find the edit-in, edit-
out and move-to points.
EConfirm the move.
APress we to move the arrow to “PREVIEW”, then
press ENTER to preview the part approximately 5
seconds before and after the point to which the scene
has been moved.
BPress we to select “EXECUTE”, then press ENTER.
●The selected scene is moved.
To modify the points
APress we to move the arrow to “CLEAR”, then press
ENTER.
BRepeat step C–E.
FReturn to the normal screen.
Press NAVIGATION.
NOTE:
There may be a discrepancy of several seconds between the
scene you intend to edit, and the scene which is actually edited.
Delete unwanted part from play list
ASelect a play list.
Press we to move the arrow to a play list from which
you wish to delete unwanted parts, then press t.
BAccess the Editing screen.
CStart playback.
Press 4 to start playback. The playback pictures appear
in the window on the screen. The elapsed playing time
starts counting with the arrow on “IN”.
●To locate the beginning of other titles, press 2/6.
DSet edit-in and edit-out points.
AFind the point where you want the deletion to begin,
then press ENTER with the arrow on “IN”. The edit-in
time is fixed and the elapsed playing time starts
counting again.
BFind the point where you want the deletion to end,
then press ENTER with the arrow on “OUT”. The edit-
out time is fixed.
●Press 3, 4, 5, 2, 6 or 9 to find the edit-in and
edit-out points.
EConfirm the deletion.
APress we to move the arrow to “PREVIEW”, then
press ENTER to preview the scene approximately 5
seconds before and after the deleted part.
BPress we to select “EXECUTE”, then press ENTER.
●The selected scene is deleted.
To modify the points
APress we to move the arrow to “CLEAR”, then press
ENTER.
BRepeat steps C–E.
FReturn to the normal screen.
Press NAVIGATION.
NOTE:
There may be a discrepancy of several seconds between the
scene you intend to edit, and the scene which is actually edited.
Perform steps A to C of “Create Play List” (墌pg. 72) before
continuing.
APress we to move the
arrow to “EDITING”, then
press ENTER.
BPress we to move the
arrow to “DELETE
SCENE”, then press
ENTER.
DR-M10EK_01.book Page 74 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
75
Filename [DR-M10EK_09Navigation.fm]
Page 75 February 25, 2004 5:59 pm
Play back play list
ASelect the play list(s).
Press we to move the arrow on the index (small still
pictures) of the desired play list.
●When you want to correct the order, move the arrow on the
desired index and press MEMO. The number disappears and
the unit re-numbers the other play lists automatically.
●When you want to cancel the order, press 8.
BStart playback.
Press ENTER. Or simply press 4. The playback starts.
CPause playback.
Press 9.
●To resume normal playback, press 4.
DStop playback.
Press 8.
Delete play list
ASelect a play list.
APress we to move the arrow to select one play list
you want to delete, then press t.
BPress we to move the arrow to “DELETE”, then press
ENTER.
BConfirm the deletion.
Press we to select “YES”, then press ENTER.
●When you cancel the deletion, select “NO”, then press
ENTER.
CReturn to the normal screen.
Press NAVIGATION.
NOTE:
Even if a play list is deleted, the programmes recorded on a DVD
disc and the library information are not affected at all.
Modify Index
APerform steps A to C of “Create Play List” (墌pg. 72).
BPerform steps C to F of “Modify Index” (墌pg. 69).
Modify Programme Title
APerform steps A to C of “Create Play List” (墌pg. 72).
BPerform steps A to E of “Modify Programme Name”
(墌pg. 70).
Modify Category
APerform steps A to C of “Create Play List” (墌pg. 72).
BPerform steps A to D of “Modify Category”
(墌pg. 70).
Perform steps A to C of “Create Play List” (墌pg. 72) before
continuing.
●When you want the plural play
lists to be played back
continuously, press MEMO
after selecting the desired play
lists. The numbers of the
playback order appear on the
index. You can select up to 30
play lists.
Perform steps A to C of “Create Play List” (墌pg. 72) before
continuing.
DR-M10EK_01.book Page 75 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_09Navigation.fm]
Masterpage:Left+
76
Page 76 February 25, 2004 5:59 pm
NAVIGATION (cont.)
Modify Library
Information
Programme information can be registered in the unit’s memory
for up to 1,300 programmes. It is helpful when finding out on
which disc the desired programme is recorded.
Scan for Programme from library
ATurn on the unit.
Press DVD 1.
BAccess the library screen.
APress NAVIGATION. The Library Database DVD Navi
screen appears.
BPress rt w e to move the arrow to “LIBRARY”, then
press ENTER.
CSort the information.
“DISC No.” : Sort by disc number
“CATEGORY” :Sort by category
“DATE” : Sort by date
“NAME” : Sort by name
●The sorting order can be switched between ascending order
and descending order by pressing the sort buttons.
DSelect the programme(s).
Press we to move the arrow to select the desired
programme, then press ENTER.
●Playback begins automatically after the selected programme is
located.
When the disc that contains the selected programme is
not loaded
A screen prompting you to load the designated disc
appears. Place the disc whose number is displayed on the
screen after pressing ENTER to close the prompt screen.
Then perform steps B to D.
EReturn to the normal screen.
Press NAVIGATION.
NOTE:
If a disc registered in the library is recorded or modified on DVD
units from other manufacturers, it may become impossible to
operate properly.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
rtwe
ENTER
DVD 1
NAVIGATION
x
Press we to move the arrow
to the appropriate sort button
to sort the information, then
press ENTER.
DR-M10EK_01.book Page 76 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
77
Filename [DR-M10EK_09Navigation.fm]
Page 77 February 25, 2004 5:59 pm
Register disc
ATurn on the unit.
Press DVD 1.
BLoad a disc.
APress x to open the disc tray.
BPlace a disc you want to register on the disc tray.
●For details, refer to “Placing a Disc” (墌pg. 10).
CPress x to close the disc tray.
CAccess the library screen.
APress NAVIGATION. The Library Database DVD Navi
screen appears.
BPress rt w e to move the arrow to “LIBRARY”, then
press ENTER.
DRegister the disc.
Press we to move the arrow to “REGISTER”, then press
ENTER.
EConfirm the registration.
Press we to select “REGISTER”, then press ENTER.
FReturn to the normal screen.
Press NAVIGATION.
NOTES:
●It is not possible to register discs used for On-Disc Timer
Programming. (墌pg. 60)
●It is not possible to register discs formatted on devices other
than JVC’s DVD recorders.
●It is not possible to register discs recorded on devices other
than JVC’s DVD recorders.
●It is not possible to register discs when “SAVE AS LIBRARY” is
set to “OFF” in FUNCTION SET UP menu. (墌pg. 94)
Delete information
ATurn on the unit.
Press DVD 1.
BAccess the library screen.
APress NAVIGATION. The Library Database DVD Navi
screen appears.
BPress rt w e to move the arrow to “LIBRARY”, then
press ENTER.
CSelect a programme.
APress rt w e to move the arrow to the appropriate
sort button to sort the information, then press ENTER.
BPress we to move the arrow to a programme you
want to delete, then press t.
DDelete the programme.
Press rt w e to move the arrow to “DELETE”, then
press ENTER.
EConfirm the deletion.
Press we to select “DELETE”, then press ENTER.
FReturn to the normal screen.
Press NAVIGATION.
DR-M10EK_01.book Page 77 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_09Navigation.fm]
Masterpage:Left+
78
Page 78 February 25, 2004 5:59 pm
NAVIGATION (cont.)
Playback with MP3/JPEG Navigation
This unit can play back discs that MP3 sound files and JPEG image files taken with digital still cameras or other devices are recorded.
The MP3/JPEG Navigation enables you to search and select the desired files recorded on CD-R/RW or CD-ROM discs very easily.
The following screen appears as the MP3/JPEG Navigation screen when you press NAVIGATION. You can move the arrow to select
the desired position on the screen by pressing rt w e on the remote control.
AName of the inserted disc.
BSort buttons (“MP3”⁄“JPEG”)
CSelected group number/total number of groups on the
disc
DGroup name
EReturn button (“RETURN”)
FGroup name/Created date
GFile type indicator
:MP3
:JPEG
HSelected file
ISelected file number/total number of files in the group
that contains the selected file
JProgramme number/file name
DR-M10EK_01.book Page 78 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
79
Filename [DR-M10EK_09Navigation.fm]
Page 79 February 25, 2004 5:59 pm
Locating the desired group and tracks
ALoad a disc.
APress x to open the disc tray.
BPlace a disc on the disc tray.
●For details, refer to “Placing a Disc” (墌pg. 10).
CPress x to close the disc tray.
BAccess the MP3/JPEG Navigation screen.
Press NAVIGATION. The MP3/JPEG Navigation screen
appears.
CDisplay the item.
For MP3 Playback
Press we to move the arrow to “MP3”.
●Only groups which contain MP3 files appear.
For JPEG Playback
Press we to move the arrow to “JPEG”.
●Only groups which contain JPEG files appear.
DSelect the group.
ESelect the item.
NOTES:
●If you press 4 instead of ENTER in step D, the unit starts
playback from the first file of the group.
●JPEG files are played back as a slide show at the set intervals.
(墌pg. 48, “Select the switching interval of the slide show”)
●If a file name includes any 2-byte character, the unit may not
show the file name correctly.
●Press rt to move the arrow to “RETURN”, then press ENTER
to return to the screen that shows the group(s).
●The order of the groups and items shown in step D and E may
differ from the order shown on your PC.
Programme Playback
ASelect the items in the desired order.
Press rt w e to move the arrow to the desired item,
then press MEMO.
●The order number appears on the left of the track name.
●Repeat this step as necessary.
●To cancel the track, press rt w e to move the arrow to the
track, then press &.
●Pressing 8 clears all the order numbers.
BStart playback.
Press 4.
●To quit the Programme Playback, press 8.
●Repeat playback can be performed if it is set as such in Play
Set Up menu. (墌pg. 44, “Repeat Playback”)
NOTES:
●It is not possible to select tracks and images simultaneously.
●It is not possible to select tracks or images in other groups.
On completion of the playback of all the items
APerform steps A to D of “Locating the desired group
and tracks” in the left column.
BPress 8.
●The order numbers are reset and cleared.
CPress NAVIGATION to complete the procedure.
Press we to move the arrow
to the desired group, then
press ENTER.
For MP3 Playback
●The tracks in the selected
group appear.
For JPEG Playback
●The images in the selected
group appear.
Press rt w e to move the
arrow to the desired item,
then press ENTER. The unit
starts playback from the
selected item.
●The unit stops when all items
in the selected group are
played back.
Perform steps A to D of “Locating the desired group and
tracks” in the left column before continuing.
DR-M10EK_01.book Page 79 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_10Editing.fm]
Masterpage:Left0
80
Page 80 February 27, 2004 9:47 am
EDITING
DV Dubbing
You can dub programmes from a camcorder or DV equipment
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected camcorder or
DV equipment functions during dubbing.
NOTE:
When you connect a PC to the DV IN connector, we do not
assure the normal operation of this unit.
1
STANDBY/ON
DV
F1
S-VIDEO VIDEO
L(MONO)
-
AUDIO
-
R
DV IN
REC MODE
SAT#
VIDEO
DV IN connector
DV cable
VC-VDV 204U
(not provided)
Camcorder
DV connector
Your unit
DV equipment
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PA U S EREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
ON SCREEN
79
4
5
3
PR +/–
rtwe
ENTER
8
REC MODE
DR-M10EK_01.book Page 80 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
81
Filename [DR-M10EK_10Editing.fm]
Page 81 February 27, 2004 9:47 am
AMake connections.
Connect a camcorder or DV equipment to the DV IN
connector on the unit’s front panel.
BPrepare the unit for dubbing.
CPress we to move H to , then press
ENTER.
DPress rt repeatedly to select the desired sound track,
then press ENTER.
●Note that this selection is not available when the source
programme is recorded in 16BIT (48 kHz) mode.
EPress REC MODE repeatedly until the desired
recording speed appears. (墌pg. 54, “Recording
Speed”)
CPrepare the DV equipment for dubbing.
Locate the point from where you want to start dubbing,
then stop or pause playback by pressing the following
buttons on the remote control:
4, 5, 3, 8, 9
●To play back in slow speed (1/10 of the normal speed), press 9
to pause playback, then press 3 or 5.
●To play back frame-by-frame, press 9 to pause playback, then
press 9 repeatedly. Each press of 9 advances a frame.
●To change the playback direction, press 3 or 5.
DStart dubbing.
Press we to move the arrow to , then press
ENTER.
●Playback on the external DV equipment and recording on the
unit should start simultaneously.
●When the playback from the beginning is not possible, the
“DV DUBBING” controller cannot be used. Perform dubbing
without using the “DV DUBBING” controller. (墌right
column)
●To pause dubbing, press we to move H to , then
press ENTER. Both the unit and the external DV equipment
pause dubbing. Pressing 9 on the unit also works the same
way.
●To clear the “DV DUBBING” controller from the TV screen,
press ON SCREEN.
EStop dubbing.
Press 8 on the remote control.
●Both the unit and the external DV equipment stop dubbing.
NOTES:
●Dubbing copyright guarded programmes is not possible.
●Original DV informations such as the recording date and time
are not recorded.
●The superimposed indication during the operation or dubbing
is not recorded.
●Only DV format image can be dubbed; MPEG2 format image
cannot be dubbed.
Performing dubbing without using the “DV DUBBING”
controller
APress PR +/– to set the channel to “DV DUBBING”.
BPress REC MODE repeatedly until the desired recording
speed appears.
CStart playback on the external DV equipment slightly before
the actual point from where you wish to start dubbing.
DPress and hold 7, then press 4 on the remote control, or
press 7 on the unit.
●Dubbing starts.
EWhen the dubbing ends, press 8 on the unit, then stop
playback on the external DV equipment.
ALoad a DVD-RAM/RW/R
disc on the unit.
BPress PR +/– to set the
channel to “DV
DUBBING”.
●The “DV DUBBING”
controller appears on the TV
screen.
●If “ ” does not appear on
the “DV DUBBING”
controller, make sure the DV
equipment is connected
correctly.
AUDIO 1: Select this to record the original stereo sound
played back on the connected DV
equipment.
AUDIO 2: Select this to record the dubbed stereo sound
played back on the connected DV
equipment.
MIX: Select this to record the sound of both
“AUDIO 1” and “AUDIO 2”.
DR-M10EK_01.book Page 81 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_10Editing.fm]
Masterpage:Left+
82
Page 82 February 27, 2004 9:47 am
EDITING (cont.)
Edit From A
Camcorder
You can use a camcorder as the source player and your
unit as the recording deck.
AMake connections.
AIf the camcorder has no S-VIDEO output connector:
— connect the camcorder’s AUDIO OUT and VIDEO
OUT connectors to the unit’s AUDIO and VIDEO
input connectors on the front panel.
BIf the camcorder has an S-VIDEO output connector:
— connect the camcorder’s AUDIO OUT and
S-VIDEO OUT connectors to the unit’s AUDIO and
S-VIDEO input connectors on the front panel.
●When using a monaural camcorder, connect its AUDIO OUT
connector to the AUDIO L input connector on your unit.
BSet the unit’s input mode.
Press PR +/– to set the channel to “F-1”.
●Set “F-1 INPUT” to “VIDEO” for the VIDEO input connector,
or “S-VIDEO” for the S-VIDEO input connector, depending on
the connector being used. (墌pg. 85, “F-1 Input Setting
(F-1 INPUT)”)
CSet the recording speed.
Press REC MODE repeatedly until the desired recording
speed appears.
DPrepare the camcorder for dubbing.
Start playback on the camcorder slightly before the actual
point from where you wish to start dubbing.
EStart dubbing.
Press and hold 7, then press 4 on the remote control, or
press 7 on the unit.
FStop dubbing.
Press 8 on the unit, then stop playback on the
camcorder.
NOTES:
●All necessary cables can be obtained from your dealer.
●Refer to the camcorder’s instruction manual for operating
procedure.
●The quality of dubbed picture becomes poorer than that of the
original.
1
STANDBY/ON
DV
F1
S-VIDEO VIDEO
L(MONO)
-
AUDIO
-
R
DV IN
REC MODE
1
STANDBY/ON
DV
F1
S-VIDEO VIDEO
L(MONO)
-
AUDIO
-
R
DV IN
REC MODE
AIf the camcorder has no S-VIDEO output connector:
BIf the camcorder has an S-VIDEO output connector:
Recorder
AUDIO OUT
VIDEO OUT
Camcorder
AUDIO input
Player
VIDEO input
Video cable (not provided)
Recorder
Audio cable (not provided)
S-VIDEO OUT
AUDIO OUT
Camcorder
S-VIDEO input
Player
AUDIO input
S-Video cable (not provided)
Audio cable (not provided)
Slide the TV/CABLE/SAT/DVD switch to DVD.
DR-M10EK_01.book Page 82 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
83
Filename [DR-M10EK_10Editing.fm]
Page 83 February 27, 2004 9:47 am
Edit To Or From
Another Recorder
You can use your unit as the source player or as the
recording deck.
AMake connections.
Connect the player’s 21-pin SCART connector to the
unit’s 21-pin SCART connector as illustrated.
AWhen using your unit as the source player:
— connect its L-1 IN/OUT connector to the recording
deck.
BWhen using your unit as the recording deck:
— connect its L-1 IN/OUT or L-2 IN/DECODER
connector to the source player.
●If another recorder is compatible with the Y/C signal:
— when using your unit as the source player, set “L-1
OUTPUT” to “SCART S-VIDEO”. (墌pg. 84, “L-1 Output and
L-1 Input Setting (L-1 OUTPUT and L-1 INPUT)”)
— when using your unit as the recording deck, set “L-2
SELECT” to “S-VIDEO”. (墌pg. 85, “L-2 Select Setting
(L-2 SELECT)”)
BSet the input mode of recording deck.
With this unit, press PR +/– to select “L-1” for the L-1 IN/
OUT connector, or “L-2” for the L-2 IN/DECODER
connector, depending on the connector being used.
●When using another recorder as the recording deck, refer to its
instruction manual.
●When using the L-2 IN/DECODER connector, set “L-2
SELECT” to “VIDEO” or “S-VIDEO”. (墌pg. 85, “L-2 Select
Setting (L-2 SELECT)”)
CSet the recording speed.
Press REC MODE repeatedly until the desired recording
speed appears.
DStart the source player.
Engage the Play mode of the source player.
EStart the recording deck.
Engage the Record mode of the recording deck.
FStop dubbing.
Stop recording on the recording deck, then stop playback
on the source player.
NOTES:
●All necessary cables can be obtained from your dealer.
●For Y/C signal input/output, be sure to use a 21-pin SCART
cable that is compatible with the Y/C signal.
●When you use this unit as the source player for editing, be sure
to set “SUPERIMPOSE” to “OFF” before starting. (墌pg. 95)
●If you are using another recorder with S-Video and Audio
output connectors, connect its S-Video and Audio output
connectors to this unit’s S-VIDEO and AUDIO input
connectors on the front panel. Then, set the unit’s input mode
to “F-1” in step B, and set “F-1 INPUT” to “S-VIDEO”.
(墌pg. 85, “F-1 Input Setting (F-1 INPUT)”)
21-pin SCART cable
(provided)
Recorder
Your unit
Another recorder
Player
TV receiver
21-pin SCART cable
(not provided)
Recorder Your unit
Another recorder
Player
TV receiver
21-pin SCART cable
(not provided)
21-pin SCART
cable
(provided)
Slide the TV/CABLE/SAT/DVD switch to DVD.
DR-M10EK_01.book Page 83 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_10Editing.fm]
Masterpage:Left+
84
Page 84 February 27, 2004 9:47 am
EDITING (cont.)
Output/Input Set
L-1 Output and L-1 Input Setting
(L-1 OUTPUT and L-1 INPUT)
The L-1 IN/OUT connector accepts and delivers either a
composite signal (regular video signal) or a Y/C signal (a signal
in which the luminance and chrominance signals are separated).
Set “L-1 OUTPUT” and “L-1 INPUT” to the appropriate mode
depending on the type of appliance connected to the unit’s L-1
IN/OUT connector.
AAccess the Main Menu screen.
Press SET UP.
BAccess the Output/Input Set screen.
CSelect the output or input mode for the L-1
IN/OUT connector.
(The boldface settings in the table below indicate the settings at
your purchase.)
DReturn to the normal screen.
Press SET UP.
NOTES:
●If “L-1 OUTPUT” is set to “SCART S-VIDEO”, “SCART RGB”
or “COMPONENT”, it is not possible to set “L-1 INPUT” to
“S-VIDEO”.
●If “L-2 SELECT” is set to “DECODER”, it is not possible to set
“L-1 INPUT” to “S-VIDEO”.
●If “L-2 SELECT” is set to “DECODER”, it is only possible to set
“L-1 OUTPUT” to “SCART VIDEO”.
●Component video signals are not output from the L-1 IN/OUT
connector.
●When Progressive scan mode is engaged, it is not possible to
select the setting of “L-1 OUTPUT”. (墌pg. 108)
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
APress we to move the
arrow to“FUNCTION SET
UP”, then press ENTER.
BPress we to move the
arrow to “VIDEO IN/
OUT”, then press ENTER.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
TV/CBL/SAT
TV TV AV
VIDEO
TV%
SHOW VIEW/
VIDEO Plus
+
rtwe
ENTER
SET UP
DVDTV
CABLE/SAT
APress rt to move the
arrow to “L-1 OUTPUT”
or “L-1 INPUT”, then
press ENTER.
BPress rt to select the
appropriate setting, then
press ENTER.
8L-1 OUTPUT
SCART VIDEO: If a connected appliance’s input is
compatible only with regular
video signals, set to “SCART
VIDEO”.
SCART S-VIDEO: If a connected appliance’s input is
compatible with Y/C signals, set to
“SCART S-VIDEO”. You can
obtain high-quality picture. (For
connection, be sure to use a 21-
pin SCART cable that is
compatible with the Y/C signal.)
SCART RGB: If a connected appliance’s input is
compatible with RGB signals, set
to “SCART RGB”. You can obtain
a high-quality RGB picture.
COMPONENT: If a connected appliance’s input is
compatible with Y/PB/PR signals,
set to “COMPONENT”. You can
obtain a high-quality Y/PB/PR
picture. Switch the TV to the input
that you can watch component
video pictures.
8L-1 INPUT
VIDEO: If a connected appliance’s output is
compatible only with regular video
signals, set to “VIDEO”.
S-VIDEO: If a connected appliance’s output is
compatible with Y/C signals, set to
“S-VIDEO”. You can obtain a high-
quality picture. (For connection, be
sure to use a 21-pin SCART cable that
is compatible with the Y/C signal.)
DR-M10EK_01.book Page 84 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
85
Filename [DR-M10EK_10Editing.fm]
Page 85 February 27, 2004 9:47 am
L-2 Select Setting (L-2 SELECT)
Set “L-2 SELECT” to the appropriate mode depending on the
type of appliance connected to the unit’s L-2 IN/DECODER
connector.
ASelect the input mode for the L-2 IN/
DECODER connector.
(The boldface settings in the table below indicate the settings at
your purchase.)
BReturn to the normal screen.
Press SET UP.
NOTES:
●If you have a satellite receiver or a decoder connected to the
L-2 IN/DECODER connector, be sure to set “L-2 SELECT” back
to appropriate mode after editing.
●If you are not connecting a satellite receiver or a decoder to
the L-2 IN/DECODER connector, leave “L-2 SELECT” set to
“VIDEO”.
●When “L-2 SELECT” is set to “SAT VIDEO” and “SAT
S-VIDEO”, “SAT” appears on the TV screen or front display
panel instead of “L-2”.
●If “L-1 OUTPUT” is set to “SCART S-VIDEO”, it is not possible
to set “L-2 SELECT” to “DECODER” or “SAT VIDEO”.
●If “L-1 OUTPUT” is set to “SCART RGB”, it is not possible to
set “L-2 SELECT” to “DECODER” or “SAT S-VIDEO”.
●If “L-1 OUTPUT” is set to “COMPONENT” and “L-2 SELECT”
to “SAT VIDEO”, “SAT S-VIDEO” or “DECODER”, be sure to
connect the L-1 IN/OUT connector with a TV.
F-1 Input Setting (F-1 INPUT)
Set “F-1 INPUT” to the appropriate mode depending on the
connector (VIDEO or S-VIDEO) being used on the front panel.
ASelect the input mode for the VIDEO/
S-VIDEO connector.
(The boldface settings in the table below indicate the settings at
your purchase.)
BReturn to the normal screen.
Press SET UP.
Perform steps A and B of “L-1 Output and L-1 Input Setting
(L-1 OUTPUT and L-1 INPUT)” on page 84.
APress rt to move the
arrow to “L-2 SELECT”,
then press ENTER.
BPress rt to select the
appropriate setting, then
press ENTER.
8L-2 SELECT
Select “VIDEO” or “S-VIDEO” to use this unit as the
recording deck with the player connected to the L-2 IN/
DECODER connector, or to use the satellite receiver
connected to the L-2 IN/DECODER connector.
VIDEO: If a connected appliance’s output is
compatible only with regular video
signals, set to “VIDEO”.
S-VIDEO: If a connected appliance’s output is
compatible with Y/C signals, set to
“S-VIDEO”. You can obtain high-
quality picture. (For connection, be
sure to use a 21-pin SCART cable
that is compatible with the Y/C
signal.)
Select “SAT VIDEO” or “SAT S-VIDEO” to view a satellite
programme with the TV set while the unit is turned off.
(墌pg. 90)
SAT VIDEO: If a connected satellite receiver’s
output is compatible only with
regular video signals, set to “SAT
VIDEO”.
SAT S-VIDEO:If a connected satellite receiver’s
output is compatible with Y/C
signals, set to “SAT S-VIDEO”. You
can obtain a high-quality S-VHS
picture. (For connection, be sure to
use a 21-pin SCART cable that is
compatible with the Y/C signal.)
DECODER: To use a decoder connected to the
L-2 IN/DECODER connector.
Perform steps A and B of “L-1 Output and L-1 Input Setting
(L-1 OUTPUT and L-1 INPUT)” on page 84.
APress rt to move the
arrow to “F-1 INPUT”,
then press ENTER.
BPress rt to select the
appropriate setting, then
press ENTER.
8F-1 INPUT
VIDEO: When connecting an appliance to
the VIDEO input connector, set to
“VIDEO”.
S-VIDEO: When connecting an appliance to
the S-VIDEO input connector, set to
“S-VIDEO”.
DR-M10EK_01.book Page 85 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_10Editing.fm]
Masterpage:Left+
86
Page 86 February 27, 2004 9:47 am
EDITING (cont.)
Digital Audio
Dubbing
You can dub selected audio from a DVD or Audio CD disc to a
digital audio device.
However, it is not possible to dub copy-protected discs.
Example: Dubbing to an MD
AMake connections.
Connect the unit and a digital audio device using either
an optional optical cable or an optional coaxial cable.
BPlace a disc and load an MD.
For the unit
APress x to open the disc tray.
BPlace a disc on the disc tray.
CPress x to close the disc tray.
For the digital audio device
Load an MD.
CPrepare the unit for dubbing.
ASelect the audio to be dubbed.
BStart playback slightly before the actual point from
where you wish to start dubbing.
CPress 9 to pause playback.
DPrepare the digital audio device for dubbing.
Select the input mode.
EStart dubbing.
APress 4 to start playback on the unit.
BStart recording on the digital audio device.
FStop dubbing.
Stop recording on the digital audio device. Then press 8
to stop playback on the unit.
NOTE:
There may be a discrepancy of several seconds between where
you intend editing to start, and where it actually starts.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
Rear of unit
Note for connection:
Remove the protection
cap from the cable.
Digital audio
device
(MD deck, etc.)
Optical cable
(not provided)
DIGITAL OUT
(OPTICAL)
Player
Recorder
Coaxial cable
(not provided)
DIGITAL OUT
(COAXIAL)
DR-M10EK_01.book Page 86 Friday, February 27, 2004 10:07 AM
Masterpage:Right0
87
Filename [DR-M10EK_10Editing.fm]
Page 87 February 27, 2004 3:12 pm
REMOTE CONTROL
Remote Control
Functions
Remote 1/2/3/4 Code Switching
The remote control is capable of controlling four JVC video units
independently. Each of the units can respond to one of four
codes (1, 2, 3 or 4). The remote control is preset to send 3 code
signals because your unit is initially set to respond to 3 code
signals. You can easily modify your unit to respond to 2, 3 or 4
code signals.
On the remote control
Keep pressing SET UP down during steps A–B.
AChange the remote control code.
Press the number key “1” for 1, “2” for 2, “3” for 3 or
“4” for 4.
BSet the remote control code.
Press ENTER to set the code.
On the unit
CTurn off the unit.
Press 1 on the unit.
DDisplay the code.
Press 4 on the unit for over 5 seconds while the unit is
turned off.
●The code currently set appears on the front display panel.
EChange the unit’s code.
Press 8 on the remote control.
●The code currently set on the remote control blinks on the
front display panel for approximately 5 seconds, and is
applied to the unit.
NOTE:
When “POWER SAVE” is set to “ON” (墌pg. 95), it is not
possible to change the remote code.
Slide the TV/CABLE/SAT/DVD switch to DVD.
1
STANDBY/ON
S-VIDEO VIDEO
L(MONO)
-
AUDIO
-
R
DV
DV IN
F1
REC MODE
SAT#
VIDEO
PULL - OPEN
1
4
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
DVD F
ENTER
SET UP
8
1 – 4
DVDTV
CABLE/SAT
DR-M10EK_10Editing.fm Page 87 Friday, February 27, 2004 3:13 PM
Filename [DR-M10EK_10Editing.fm]
Masterpage:Left+
88
Page 88 February 27, 2004 9:47 am
REMOTE CONTROL (cont.)
TV Multi-Brand Remote Control
Your remote control can operate the basic functions of your TV
set. In addition to JVC TVs, other manufacturer’s TVs can also be
controlled.
IMP
O
RTANT:
Although the provided remote control unit is compatible with
JVC televisions, as well as many other models, it may not work
with your TV, or in some instances, may have limited function
capability.
ASet the TV brand code.
Keep pressing SET UP down during step A.
Enter your TV’s brand code using the number keys, then
press ENTER.
Press TV/CBL/SAT 1 on the unit’s remote control to turn
on the TV and try operations (墌 step B).
●Once you have set the remote control to operate the TV, you
do not have to repeat this step until you replace your remote
control’s batteries.
●Some brands of TVs have more than one code. If the TV does
not function with one code, try entering another.
BOperate the TV.
Press the corresponding button: TV/CBL/SAT 1, TV AV/
VIDEO, PR +/–, TV %+/– (Volume), TV (TV Muting),
number keys.
●For some brands of TVs, you must press ENTER after having
pressed the number keys.
Before performing the following steps:
●Turn off the TV using its remote control.
●Slide the TV/CABLE/SAT/DVD switch to TV.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
SET UP
0 – 9
ENTER
TV
PR +/–
TV %
+/–
TV AV/
VIDEO
TV/CBL/SAT
1
DVDTV
CABLE/SAT
BRAND NAME CODE
JVC
HITACHI
MAGNAVOX
MITSUBISHI
PANASONIC
RCA
SHARP
SONY
SAMSUNG
SANYO
SEARS
TOSHIBA
ZENITH
01, 03
10
02
03
04, 11
05
06
07
12
13
13
08
09
DR-M10EK_01.book Page 88 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
89
Filename [DR-M10EK_10Editing.fm]
Page 89 February 27, 2004 9:47 am
Satellite Receiver Multi-Brand Remote
Control
Your remote control can operate the basic functions of your
satellite receiver set. In addition to JVC satellite receivers, other
manufacturer’s satellite receivers can also be controlled.
IMP
O
RTANT:
Although the provided remote control unit is compatible with
JVC satellite receivers, as well as many other models, it may not
work with your satellite receiver, or in some instances, may have
limited function capability.
ASet the satellite receiver brand code.
Keep pressing SET UP down during step A.
Enter your satellite receiver’s brand code using the
number keys, then press ENTER.
Press TV/CBL/SAT 1 on the unit’s remote control to turn
on the satellite receiver and try operations (墌step B).
●Once you have set the remote control to operate the satellite
receiver, you do not have to repeat this step until you replace
your remote control’s batteries.
●Some brands of satellite receiver have more than one code. If
the satellite receiver does not function with one code, try
entering another.
BOperate the satellite receiver.
Press the corresponding button: TV/CBL/SAT 1, PR +/–,
number keys.
●For some brands of satellite receiver, you must press ENTER
after having pressed the number keys.
●The number keys may not function with some satellite
receivers.
Slide the TV/CABLE/SAT/DVD switch to CABLE/SAT.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
SET UP
0 – 9
ENTER
TV/CBL/SAT
1
PR +/–
BRAND NAME CODE
JVC
AMSTRAD
CANAL SATELLITE
CANAL +
D-BOX
ECHOSTAR (VIA DIGITAL)
FINLUX
FORCE
GALAXIS
GRUNDIG
HIRSCHMANN
HUMAX
ITT NOKIA
KATHREIN
LUXOR
MASCOM
MASPRO
NOKIA
PACE
PANASONIC
PHILIPS
RADIX
RFT
SABA
SAGEM
SALORA
SAMSUNG
SIEMENS
SKYMASTER
TECHNISAT
THOMSON
TPS
TRIAX
WISI
73
60, 61, 62, 63, 92
81
81
85
82
68
89
88
64, 65, 102
64, 78, 99
88
68
70, 71, 96
68
93
70
87, 94
65, 67, 74, 86, 92
74, 92
66, 84, 101
78
69
97
83, 90
68
83
64
69, 98
66, 100
97
83
91
64
DR-M10EK_01.book Page 89 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_10Editing.fm]
Masterpage:Left0
90
Page 90 February 27, 2004 9:47 am
SYSTEM CONNECTIONS
Connecting To A Satellite Receiver
Connect the satellite receiver to the L-2 IN/DECODER connector, then connect the L-1 IN/OUT connector to the TV’s
connector.
NOTES:
●Set “L-2 SELECT” to “VIDEO” or “S-VIDEO”. (墌pg. 85)
●You can use the Automatic Satellite Programme Recording function (墌pg. 65) with this connection.
●To record a programme via the satellite receiver, select L-2 mode by pressing PR +/– so that “L-2” appears on the front display panel.
●For details, refer to the instruction manual of the satellite receiver.
IMP
O
RTANT:
When you set “L-2 SELECT” to “SAT VIDEO” or “SAT S-VIDEO” (墌pg. 85, “L-2 Select Setting (L-2 SELECT)”), it is possible to view
a satellite broadcast with the TV set to its AV mode even if the unit is turned off. When the unit is in Stop mode or recording, press
on the remote control to turn off the VIDEO indicator on the unit.
●If you turn on the unit when the satellite receiver’s power is off, nothing appears on the TV screen. In this case, turn on the
satellite receiver, or set the TV to its TV mode, or press on the remote control to set the unit to the AV mode.
Outdoor unit
Satellite cable
Satellite receiver
Aerial
TV aerial cable
21-pin SCART connector
Back of TV
Aerial connector
Mains outlet
Back of unit
ANTENNA IN
ANTENNA OUT
DR-M10EK_01.book Page 90 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
91
Filename [DR-M10EK_10Editing.fm]
Page 91 February 27, 2004 9:47 am
Connecting To A Dolby Digital Decoder
Or An Amplifier With Built-in DTS
These instructions enable you to connect your unit to a Dolby Digital decoder or an amplifier with built-in DTS.
Make connections.
Connect the unit and a Dolby Digital decoder or an
amplifier with built-in DTS using either an optional
optical cable or an optional coaxial cable.
NOTES:
●For Dolby Digital sound, set “DIGITAL AUDIO OUT” to
“DOLBY DIGITAL/PCM”. (墌pg. 93)
●For DTS sound, set “DIGITAL AUDIO OUT” to “STREAM/
PCM”. (墌pg. 93)
CAUTIONS:
●This unit has a dynamic range of more than 110 dB with
regards to its Hi-Fi audio capability. It is recommended that
you check the maximum level if you are going to listen to the
Hi-Fi audio signals through a stereo amplifier. A sudden surge
in the input level to the speakers may damage them.
●Some speakers and televisions are specially shielded to
prevent television interference. If both are of the non-shielded
type, do not place the speakers adjacent to the TV set as this
can adversely affect the playback picture.
Back of unit
Note for connection:
Remove the protection
cap from the optical
cable.
Optical cable
(not provided)
Dolby Digital
decoder or amplifier
with built-in DTS
To DIGITAL AUDIO
input Coaxial cable
(not provided)
DIGITAL OUT
(OPTICAL)
DIGITAL OUT
(COAXIAL)
When you can’t switch the audio channel of a
bilingual programme
When the unit is connected with a digital audio device using
an optional optical cable and “DIGITAL AUDIO OUT” is set
to “DOLBY DIGITAL/PCM”, it is not possible to switch the
audio channel of a bilingual programme recorded on a
DVD-RAM or DVD-RW (VR mode) disc. In this case, perform
the following steps using the remote control to switch
“DIGITAL AUDIO OUT” from “DOLBY DIGITAL/PCM” to
“PCM ONLY”.
APress SET UP to access the Main Menu screen.
BPress we to select “DVD SET UP”, then press ENTER.
CPress we to select “AUDIO OUTPUT”, then press
ENTER.
DPress rt to select “DIGITAL AUDIO OUT”, then press
ENTER.
EPress rt to select “PCM ONLY”, then press ENTER.
(墌pg. 93)
FPress SET UP to complete the setting.
GPress AUDIO to select the desired audio channel.
(墌pg. 36, “Audio Channel Selection”)
DR-M10EK_01.book Page 91 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_11Subsidiary.fm]
Masterpage:Left0
92
Page 92 February 27, 2004 5:54 pm
SUBSIDIARY SETTINGS
Mode Set Various modes of this unit are categorized into menus nested in
2 levels shown in the following table. To change the settings of
these modes, find the desired mode in the menu (for details on
each menu, see pages 93 through 96), then follow the procedure
below.
●The procedure below shows how to set the desired option of
the “AUDIO REC” mode as an example.
AAccess the Main Menu screen.
Press SET UP.
BAccess the “RECORDING SET” screen.
CSelect the desired option.
DComplete the setting.
Press SET UP.
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
rtwe
ENTER
SET UP
DVD SET UP LANGUAGE SET (墌pg. 26)
AUDIO OUTPUT (墌pg. 93)
UTILITY (墌pg. 49, 106, 107)
FUNCTION SET UP VIDEO IN/OUT (墌pg. 25, 84)
RECORDING SET (墌pg. 94)
DISPLAY SET (墌pg. 95)
OTHERS (墌pg. 96)
INITIAL SET UP AUTO CH SET (墌pg. 98)
MANUAL CH SET (墌pg. 99)
SAT/GUIDE PR (墌pg. 29, 97)
CLOCK SET (墌pg. 104)
APress we to select
“FUNCTION SET UP”,
then press ENTER.
BPress we to select
“RECORDING SET”, then
press ENTER.
APress rt to select
“AUDIO REC”, then press
ENTER.
BPress rt to select the
desired option, then press
ENTER.
DR-M10EK_11Subsidiary.fm Page 92 Friday, February 27, 2004 5:57 PM
Masterpage:Right-No-Heading
93
Filename [DR-M10EK_11Subsidiary.fm]
Page 93 February 27, 2004 9:47 am
AUDIO OUTPUT
(The boldface settings in the table below indicate the settings at your purchase.)
8DIGITAL AUDIO OUT
DOLBY DIGITAL/PCM
STREAM/PCM
PCM ONLY
Set to the appropriate mode according to the type of the device connected to
DIGITAL OUT connector.
DOLBY DIGITAL/PCM:
Select this when you connect the digital input connector of a Dolby
Digital decoder or an amplifier with a built-in Dolby Digital
decoder.
STREAM/PCM:
Select this when you connect the digital input connector of an
amplifier with a built-in DTS, Dolby Digital, or MPEG multichannel
decoder.
PCM ONLY:
Select this when you connect the linear PCM digital input of other
audio equipment (amplifier, MD or DAT deck, etc.).
8ANALOG AUDIO OUT
STEREO
DOLBY SURROUND
Select the appropriate setting to accommodate the unit to the connected A/V
equipment. This function takes effect when a DVD VIDEO disc is played back.
STEREO:
Select this when listening to conventional two-channel stereo audio
with the unit’s AUDIO OUT connectors connected to a stereo
amplifier/receiver or TV set, or in case you want to record the audio
from a DVD VIDEO disc to a Mini Disc, etc.
DOLBY SURROUND:
Select this when listening to multichannel surround audio with the
unit’s AUDIO OUT connectors connected to an amplifier/receiver
with a built-in surround decoder or a surround decoder.
8D. RANGE CONTROL
NORMAL
WIDE RANGE
TV MODE
The dynamic range (the difference between the loudest sound and the quietest
one) can be compressed during playback of a programme encoded in Dolby
Digital format.
This function takes effect when a DVD VIDEO disc recorded in Dolby Digital
format is played back at low or middle volume.
NORMAL:
Normally select this setting to activate this function.
WIDE RANGE:
Select this to deactivate this function when you enjoy wide dynamic
range programme.
TV MODE:
Select this when you hear the sound through the TV’s speaker(s).
NOTES:
●This function takes no effect on programmes other than that recorded in Dolby Digital
format.
●This function dose not work when Simulated Surround Effect is activated. (墌pg. 46)
●The effect of “NORMAL” and “WIDE RANGE” may not be different depending on discs.
8OUTPUT LEVEL
STANDARD
LOW
You can lower the output level of analog audio to accommodate the unit to the
connected A/V equipment.
STANDARD:
Normally select this setting.
LOW:
The output level of analog audio is lowered.
DR-M10EK_01.book Page 93 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_11Subsidiary.fm]
Masterpage:Left+
94
Page 94 February 27, 2004 9:47 am
SUBSIDIARY SETTINGS (cont.)
RECORDING SET
(The boldface settings in the table below indicate the settings at your purchase.)
8SAVE AS LIBRARY
OFF
ON
When this function is set to “ON”, the recording information is automatically
stored in the library. For details, refer to “Modify Library Information”
(墌pg. 76).
8XP MODE REC AUDIO
DOLBY DIGITAL
LINEAR PCM
You can select the audio format when you record a programme in XP mode.
When this function is set to “LINEAR PCM”, you can obtain a high-quality
audio sound.
DOLBY DIGITAL:
To record in Dolby Digital format.
LINEAR PCM:
To record in Linear PCM format.
8AUDIO REC
NICAM 1/MAIN
NICAM 2/SUB
MONO
You can select the desired NICAM audio channel to be recorded on a DVD-R/
RW (Video mode) disc.
NICAM 1/MAIN:
To record the main language of NICAM audio.
NICAM 2/SUB:
To record the sub language of NICAM audio.
MONO:
To record the standard (monaural) sound of NICAM audio.
NOTE:
This function works only for the NICAM bilingual programme.
8DIRECT REC
OFF
ON
When this function is set to “ON”, you can easily start recording the
programme that you are watching on your TV. Press and hold 7 and press 4
on the remote control, or press 7 on the unit.
NOTES:
●When you use the Direct Rec function, be sure to use a TV offering T-V LINK, etc. and
connect a fully-wired 21-pin SCART cable between the unit and the TV. (墌pg. 18)
●If “DIRECT REC” is set to “OFF”, the 7 button functions as described in “Basic
Recording” (墌pg. 53).
●During Direct Rec, “– –” appears on the front display panel.
●If a programme is recorded with the Direct Rec, the station name will not be registered
in the library. “– – – –” will be displayed for the station name.
●Even if there is no power supply for more than 60 minutes, the unit keeps the setting.
DR-M10EK_01.book Page 94 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
95
Filename [DR-M10EK_11Subsidiary.fm]
Page 95 February 27, 2004 9:47 am
DISPLAY SET
(The boldface settings in the table below indicate the settings at your purchase.)
8SUPERIMPOSE
OFF
AUTO
You can select the modes of indications superimposed on the TV screen.
OFF:
To turn off superimposed indications.
AUTO:
To superimpose operational indications for approximately five
seconds just after the corresponding operation.
NOTES:
●When you use this unit as the source player for editing, be sure to set “SUPERIMPOSE”
to “OFF” before starting. (墌pg. 83, “Edit To Or From Another Recorder”)
●When you select “AUTO”, during playback, the operation mode indicators may be
disturbed depending on the type of disc being used.
8GREY BACK
OFF
ON
When this function is set to “ON”, the TV screen becomes all grey when
receiving a channel not in use.
NOTE:
When you want to receive an unstable channel with poor signals, set this function to
“OFF”.
8DIMMER
BRIGHT
DIMMED1
DIMMED2
OFF
You can change the brightness of the front display panel.
BRIGHT:
Normally select this.
DIMMED1/DIMMED2:
To change the brightness level. (Blue lamp on the front display panel
become dimmer.)
OFF:
To dim the front display panel. (Blue lamp on the front display panel
is turned off.)
NOTE:
It is impossible to turn off the light of the front display completely. When “BRIGHT” or
“DIMMED1” is selected, the brightness level will be same as “DIMMED1” after the unit is
turned off. When “DIMMED2” or “OFF” is selected, the brightness level will be same as
“DIMMED2” after the unit is turned off.
8POWER SAVE
OFF
ON
When this function is set to “ON”, you can reduce the power consumption
while the unit is turned off.
NOTES:
●During Power Save mode —
— the front display panel will be turned off.
— the Just Clock function (墌pg. 104) does not work.
●Power Save does not work when —
— the unit is in the Timer mode.
— the unit’s power is turned off after timer-recording or Instant Timer Recording.
— the Automatic Satellite Programme Recording mode is engaged. (墌pg. 65)
— “L-2 SELECT” is set to “DECODER”, “SAT VIDEO” or “SAT S-VIDEO”. (墌pg. 85)
●It takes some time for the unit to complete initialisation after you turn on unit power,
with “WAKE UP” blinking on the front display panel.
DR-M10EK_01.book Page 95 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_11Subsidiary.fm]
Masterpage:Left+
96
Page 96 February 27, 2004 9:47 am
SUBSIDIARY SETTINGS (cont.)
OTHERS
(The boldface settings in the table below indicate the settings at your purchase.)
8AUTO TIMER
OFF
ON
When this function is set to “ON”, the timer is automatically engaged when the
unit power is turned off, and automatically disengaged when the unit is
powered back on.
NOTE:
For safety, when “AUTO TIMER” is set to “OFF”, all other functions are disabled while the
Timer mode is engaged. To disengage the timer, press # (TIMER).
8RESUME
ON
OFF
DISC RESUME
When this function is set to “ON” or “DISC RESUME”, you can use the resume
function. (墌pg. 33)
ON: You can start playback from the resume point of the placed
disc.
OFF: You cannot use the resume function.
DISC RESUME:
The unit retains a memory of the resume points of the last 30
discs played back, even though they have been ejected.
NOTE:
“DISC RESUME” setting works on DVD VIDEO, VCD, SVCD and already finalised DVD-
R/DVD-RW (video mode) discs. For other types of discs, the function under “ON” setting
will be applied even if “RESUME” is set to “DISC RESUME”.
DR-M10EK_01.book Page 96 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
97
Filename [DR-M10EK_11Subsidiary.fm]
Page 97 February 27, 2004 9:47 am
VIDEO Plus+® System Setup
Guide Program Number Set
AAccess the Main Menu screen.
Press SET UP.
BAccess the “SAT/GUIDE PR” screen.
CEnter the Guide Program number.
APress rt to select “GUIDE PROGRAMME”, then
press ENTER.
BPress rt to select the Guide Program number for the
desired station as shown in the TV listings. Then press
ENTER.
●To change the Guide Program number in 10 increments, press
and hold rt.
DEnter the receiving channel position number.
APress rt to select “TV PROGRAMME”, then press
ENTER.
BPress rt to select the number of the unit’s channel
position on which the Guide Program number’s
broadcast is received by the unit or the satellite
receiver. Then press ENTER.
●Pressing AUX changes “TV PROGRAMME” to “SAT”.
●To timer-record a satellite programme with the VIDEO Plus+
system, you need to install a provided Satellite Controller and
perform the procedure described in “Satellite Receiver Control
Setting” (墌pg. 28).
●Repeat steps C and D as necessary.
EComplete the setting.
Press SET UP.
IMP
O
RTANT:
Normally, Auto Set Up (墌pg. 21), Preset Download (墌pg. 23) or Auto Channel Set (墌pg. 98) sets the Guide Program numbers
automatically. You need to set the Guide Program numbers manually only in the following cases.
●When timer-programming with the VIDEO Plus+ system, the channel position, where the station you wish to record is received
on your unit, is not selected,
OR
when you add a channel after Auto Set Up, Preset Download or Auto Channel Set has taken place,
—Set the Guide Program number for that station manually.
●When you wish to timer-record a satellite programme with the VIDEO Plus+ system,
—Set the Guide Program numbers for all satellite broadcasts received on your satellite receiver.
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
APress we to select
“INITIAL SET UP”, then
press ENTER.
BPress we to select “SAT/
GUIDE PR”, then press
ENTER.
Guide Program Number
“Guide Program (GUIDE PROGRAMME) number” refers to
the assigned TV station numbers, according to broadcast
area, for the VIDEO Plus+ timer recording. The Guide
Program numbers can be found in most TV listings.
DR-M10EK_01.book Page 97 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_11Subsidiary.fm]
Masterpage:Left+
98
Page 98 February 27, 2004 3:16 pm
SUBSIDIARY SETTINGS (cont.)
Tuner Set Your unit needs to memorise all necessary stations in channel
positions in order to record TV programmes. Auto Channel Set
automatically assigns all receivable stations in your area to call
them up by using the PR +/– buttons without going through any
vacant channels.
Auto Channel Set
AAccess the Main Menu screen.
Press SET UP.
BPerform Auto Channel Set.
APress we to select “INITIAL SET UP”, then press
ENTER.
BPress we to select “AUTO CH SET”, then press
ENTER.
●When you have connected
the unit to a TV offering T-V
Link via a fully-wired 21-pin
SCART cable (墌pg. 18), the
unit automatically performs
the Preset Download and the
T-V LINK screen will appear.
(墌pg. 23)
●The Auto Set screen appears,
and remains on screen while the unit searches for receivable
stations.
Wait until the TV screen as shown in step C appears.
CView the Confirmation screen.
“SCAN COMPLETED” is
displayed on the TV screen.
Press “OK”, then the
Confirmation screen appears.
The confirmation screen lists
the channel position number
(PR), station channel number
(CH), and station name (ID)
(墌pg. 102, “TV Station And ID List”) of all stored
broadcast stations. The programme currently received on
the selected channel position appears behind the
confirmation screen. To view the next page, press
rt w e.
●The Guide Program numbers will also be set automatically
during Auto Channel Set.
DComplete the setting.
Press SET UP.
●Using the Confirmation screen, you can skip or add channel
positions, enter station names and perform other operations.
Refer to pages 99 – 101 for the procedures.
●Depending on reception conditions, the stations may not be
stored in order, and the station names may not be stored
correctly.
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
IMP
O
RTANT:
Perform the following steps only if —
— Auto Channel Set has not been set correctly by Auto Set
Up or by Preset Download. (墌pg. 21, 23)
— you have moved to a different area or if a new station
starts broadcasting in your area.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PA U S EREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
rtwe
ENTER
SET UP
DVDTV
CABLE/SAT
DR-M10EK_11Subsidiary.fm Page 98 Friday, February 27, 2004 3:35 PM
Masterpage:Right-No-Heading
99
Filename [DR-M10EK_11Subsidiary.fm]
Page 99 February 27, 2004 9:47 am
NOTES:
●Fine tuning is performed automatically during Auto Channel
Set. If you want to perform tuning manually, refer to “Fine-
Tuning Channels Already Stored” (墌pg. 101).
●If you perform Auto Channel Set when the aerial cable is not
connected properly, “SCAN COMPLETED –NO SIGNAL–”
appears on the TV screen in step C. In such a case, make sure
of the aerial connection and press ENTER; Auto Channel Set
will start again.
Manual Channel Set
Store channels that were not stored during Auto Set Up
(墌pg. 21), Preset Download (墌pg. 23) or Auto Channel Set
(墌pg. 98).
AAccess the Main Menu screen.
Press SET UP.
BAccess the Confirmation screen.
APress we to select “INITIAL SET UP”, then press
ENTER.
BPress we to select “MANUAL CH SET”, then press
ENTER.
●The Confirmation screen appears.
CSelect the channel position.
IMP
O
RTANT:
●In certain reception conditions, station names may not be
stored correctly, and Auto Guide Program Number Set may
not work properly. When the Guide Programme numbers
are not set properly, the programme that you do not
intended to record will be timer-recorded by the VIDEO
Plus+ system of the unit. When programming the timer
using the VIDEO Plus+ system, be sure to check the
desired channel is selected correctly. (墌pg. 56, “VIDEO
Plus+® Timer Programming”)
●Your unit memorises all receivable stations even if
reception of some of them is poor. You can delete those
stations with an unacceptable picture from the list.
(墌pg. 100, “Delete A Channel”)
Press rt w e to select a
blank position in which you
want to store a channel, then
press ENTER twice. The
Manual Channel Set screen
appears.
(Example) To store in position 6.
The programme currently
received on the selected channel
position appears behind the
confirmation screen.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
rtwe
ENTER
SET UP
0 – 9
DR-M10EK_01.book Page 99 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_11Subsidiary.fm]
Masterpage:Left+
100
Page 100 February 27, 2004 9:47 am
SUBSIDIARY SETTINGS (cont.)
DSelect the band.
EEnter the channel.
APress rt to select “CH”, then press ENTER.
BPress rt to input the channel number you want to
store.
●To enter the registered station name (墌pg. 102, “TV Station
And ID List”), press rt to select “ID”, then press ENTER.
Press rt.
●For fine tuning adjustment, press rt to select “FINE”, then
press ENTER. Press rt to perform fine-tuning.
●When “L-2 SELECT” is set to “VIDEO”, “S-VIDEO”, “SAT
VIDEO” or “SAT S-VIDEO”, the “DECODER” setting cannot be
changed. (墌pg. 85, “L-2 Select Setting (L-2 SELECT)”)
FEnter new channel information.
Press ENTER. The Confirmation screen appears.
●Repeat steps C–F as necessary.
GClose the Confirmation screen.
Press SET UP.
●To change positions, see “Change Station Channel Position”
(in the right column).
●If you wish to set station names other than the ones registered
in your unit, see “Set Stations (B)” (墌pg. 101).
Delete A Channel
ASelect the item.
Press rt w e to select the item you want to delete.
BDelete a channel.
Press &.
●The item next to the cancelled one moves up one line.
●Repeat steps A and B as necessary.
CClose the Confirmation screen.
Press SET UP.
Change Station Channel Position
ASelect the item.
Press rt w e to select the item you want to move, then
press ENTER.
BSelect the new position.
●Repeat steps A and B as necessary.
CClose the Confirmation screen.
Press SET UP twice.
APress rt to select
“BAND”, then press
ENTER.
BPress rt to change the
band between CH
(regular) and CC (cable),
then press ENTER.
A
TTENTI
O
N:
Guide Program numbers are not set when channels are
stored manually. (墌pg. 97, “VIDEO Plus+® System Setup”)
Perform steps A and B of “Manual Channel Set” on page 99
to access the Confirmation screen before continuing.
Perform steps A and B of “Manual Channel Set” on page 99
to access the Confirmation screen before continuing.
Press rt w e to select the
new channel position, then
press ENTER.
Example: If you moved the
station in position 4 to
position 2, the stations
originally in positions
2 and 3 each move
down one space.
DR-M10EK_01.book Page 100 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
101
Filename [DR-M10EK_11Subsidiary.fm]
Page 101 February 27, 2004 9:47 am
Set Stations (A)
Set station names that are registered in your unit.
ASelect the item.
Press rt w e to select the item you want.
BAccess the Manual Channel Set screen.
Press ENTER twice.
CSelect the new station.
APress rt to select “ID”, then press ENTER.
BPress rt until the new station’s name (ID) you want
to store appears, then press ENTER. Registered station
names (墌pg. 102, “TV Station And ID List”) appear
as you press rt.
DSwitch the stations.
Press we to select “OK”, then press ENTER.
●Repeat steps A–D as necessary.
EClose the Confirmation screen.
Press SET UP twice.
Set Stations (B)
Set station names other than the ones registered in your unit.
ASelect the character for station name.
APress rt to select “ID”, then press ENTER.
BPress ENTER twice.
BEnter the new character.
APress we to locate the character insertion point.
BPress rt to cycle through the characters (A–Z, 0–9,
–, f, +, I (space)) and stop when the desired
character is indicated, then press e to enter.
CEnter the remaining characters the same way
(maximum of 4).
DAfter entering all characters, press we to select “OK”,
then press ENTER.
CClose the Confirmation screen.
Press SET UP twice.
NOTE:
The characters available for the station name (ID) are A–Z, 0–9, –
, f, +, I (space) (maximum of 4).
Fine-Tuning Channels Already Stored
ASelect the channel to fine-tune.
APress rt w e to select the channel you want to fine-
tune, then press ENTER.
BPress ENTER twice.
BAccess the Manual Channel Set screen.
Press ENTER. The Manual Channel Set screen appears.
CPerform fine-tuning.
APress rt to select “FINE”.
BPress we until the picture appears in its best quality.
●Repeat steps A–C as necessary.
DClose the Confirmation screen.
Press SET UP three times.
Perform steps A and B of “Manual Channel Set” on page 99
to access the Confirmation screen before continuing.
Perform steps A and B of “Manual Channel Set” on page 99
to access the Confirmation screen and then perform steps A
and B of “Set Stations (A)” (墌pg. 101) before continuing.
Perform steps A and B of “Manual Channel Set” on page 99
to access the Confirmation screen before continuing.
DR-M10EK_01.book Page 101 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_11Subsidiary.fm]
Masterpage:Left+
102
Page 102 February 27, 2004 9:47 am
SUBSIDIARY SETTINGS (cont.)
TV Station And ID List
* The “ID” abbreviation is what is shown on-screen in lieu of the
station name. The “ID” abbreviation is listed in the
Confirmation screen and is displayed on the TV screen when
the unit is tuned to a different station.
STATION NAME ID*
Anglia TV
ARD
ARTE
BBC Group
BBC1
BBC2
BBCW
Berlin 1
Berlin 2
Border TV
Bayern1
Bayern3
BRT1
BRT2
Children Ch
Canal +
CNN
Channel TV
Central TV
Channel 4
Channel 5
DISC
DRS
DR TV
DSF
Euronews
Euronews
Eurosports
France1
France2
France3
Granada TV
Grampian TV
Hessen1
Hessen3
HRT
HTV
ITV Network
Kabelkanal
London
MDR
MTV
Nord3
NDR1
NDR3
NED1
NED2
NED3
Network 2
NRK
N-TV
Offener Kanal
ORF1
ORF2
ORF3
OWL 3
Premiere
PR07
RAI1
RAI2
RAI3
RB1
RB3
Rikisutvarpid-S
RTBF 1
RTBF 2
RTE 1
RTL
RTL 2
RTP
ANGL
ARD
ARTE
BBC
BBC1
BBC2
BBCW
BLN1
BLN2
BORD
BR1
BR3
BRT1
BRT2
CHLD
CH+
CNN
CHNL
CNTR
CH 4
CH 5
DISC
DRS
DRTV
DSF
EURN
EURO
EURS
FR1
FR2
FR3
GRNA
GRMP
HR1
HR3
HRT
HTV
ITV1
KABL
LNDN
MDR
MTV
N3
NDR1
NDR3
NED1
NED2
NED3
NET2
NRK
N-TV
OKAN
ORF1
ORF2
ORF3
OWL3
PRMI
PR07
RAI1
RAI2
RAI3
RB1
RB3
RKPS
RTB1
RTB2
RTE1
RTL
RTL2
RTP
STATION NAME ID*
SAT
SAT 1
Scottish TV
SC4
SDR
SDR1
SFB1
SFB3
SKY
Sky One
Sky Net
Sport
SR 1
Super RTL
STV Test
STV 1
STV 2
Suedwest3
SWF 1
Schweiz4
TYNE TEES
Text
TF1
TNT int
TRT int
TSI
TSR
TSW
TVE
TV Polonia
TVP 1
TVP 2
TVS
TV2
TV5
Tele Zurich
Ulster TV
Veronica
VIVA
VIVA2
VOX
VTM
VT4
West1
West3
YLE 1
YLE 2
Yo rk s hi r e T V
ZDF
Zurich 1
3SAT
SAT
SAT1
SCOT
SC4
SDR
SDR1
SFB1
SFB3
SKY
SKY1
SKYN
SPRT
SR1
SRTL
STVT
STV1
STV2
SWR
SWF1
SWZ4
TEES
TEXT
TF1
TNT
TRT
TSI
TSR
TSW
TVE
TVPA
TVP1
TVP2
TVS
TV2
TV5
TZUR
ULST
VERN
VIVA
VIV2
VOX
VTM
VT4
WDR1
WDR3
YLE1
YLE2
YORK
ZDF
ZUR1
3SAT
DR-M10EK_01.book Page 102 Friday, February 27, 2004 10:07 AM
Masterpage:Right 3Column
103
Filename [DR-M10EK_11Subsidiary.fm]
Page 103 February 27, 2004 9:47 am
TV Station Channel Number Guide
Only the main stations are listed. There are in addition many relay stations, and full lists are available from the BBC and ITV.
BBC1 BBC2 ITV CH4 CH5
London & South-East
Bluebell Hill.........................40 46 43 65 —
Crystal Palace.......................26 33 23 30 37
Dover...................................50 56 66 53 —
Heathfield ............................49 52 64 67 —
Oxford .................................57 63 60 53 49
South-West
Beacon Hill..........................57 63 60 53 —
Caradon Hill ........................22 28 25 32 —
Huntshaw Cross ...................55 62 59 65 67
Redruth ................................51 44 41 47 37
Stockland Hill ......................33 26 23 29 —
Channel Islands
Fremont Point.......................51 44 41 47 —
South
Hannington..........................39 45 42 66 35
Midhurst...............................61 55 58 68 —
Rowridge..............................31 24 27 21 —
West
Mendip ................................58 64 61 54 37
East
Sandy Heath.........................31 27 24 21 39
Sudbury................................51 44 41 47 35
Tacolneston ..........................62 55 59 65 52
Midlands
Ridge Hill.............................22 28 25 32 35
Sutton Coldfield ...................46 40 43 50 37
The Wrekin ..........................26 33 23 29 35
Waltham ..............................58 64 61 54 35
North
Belmont ...............................22 28 25 32 56
Emley Moor..........................44 51 47 41 37
BBC1 BBC2 ITV CH4 CH5
North-West
Caldbeck..............................30 34 28 32 56
Winter Hill........................... 55 62 59 65 48
North-East
Bilsdale West Moor ..............33 26 29 23 35
Chatton ................................ 39 45 49 42 —
Pontop Pike..........................58 64 61 54 68
Scotland
Angus................................... 57 63 60 53 —
Black Hill............................. 40 46 43 50 37
Sandale ................................ 22 ————
Caldbeck.............................. — 34 28 32 56
Creigkelly............................. 31 27 24 21 48
Darvel..................................33 26 23 29 35
Durris...................................22 28 25 32 67
Eitshal ..................................33 26 23 29 —
Keelylang Hill ...................... 40 46 43 50 —
Knock More .........................33 26 23 29 —
Rosemarkie ..........................39 45 49 42 67
Rumster Forest......................31 27 24 21 —
Selkirk.................................. 55 62 59 65 52
Wales
Blaenplwyf........................... 31 27 24 21 56
Carmel ................................. 57 63 60 53 —
Llanddona............................ 57 63 60 53 —
Moel-y-Parc..........................52 45 49 42 —
Presely .................................46 40 43 50 37
Wenvoe ...............................44 51 41 47 —
Northern Ireland
Brougher Mountain ..............22 28 25 32 —
Divis ....................................31 27 24 21 37
Limavady.............................. 55 62 59 65 —
DR-M10EK_01.book Page 103 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_11Subsidiary.fm]
Masterpage:Left+
104
Page 104 February 27, 2004 9:47 am
SUBSIDIARY SETTINGS (cont.)
Clock Set
AAccess the Main Menu screen.
Press SET UP.
BAccess the “CLOCK SET” screen.
CSet the date and time.
APress rt to select “YEAR”, then press ENTER.
BPress rt to set the year, then press ENTER.
●Repeat the same procedure to set the date and time. When
you set the time, press and hold rt to change the time by 30
minutes.
●When you set the date, press and hold rt to change the date
by 15 days.
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
Just Clock
The Just Clock function provides accurate time keeping
through automatic adjustments at regular intervals, by
reading data from a PDC signal.
The Just Clock option can be set to “ON” or “OFF” at the
Clock Set screen (the default setting is “OFF”). (墌pg. 105)
IMPORTANT: If you turn off Just Clock, the accuracy of your
unit’s built-in clock may be reduced, which could adversely
effect timer recording. We recommend you to keep Just
Clock on. In cases where the clock setting data from a PDC
signal is incorrect, however, you are advised to keep Just
Clock set to “OFF”.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
rtwe
ENTER
SET UP
DVDTV
CABLE/SAT
IMP
O
RTANT:
If you performed Auto Set Up (墌pg. 21) or Preset
Download (墌pg. 23), without ever having set the clock
previously, the unit’s built-in clock is also set automatically.
Perform the following steps only if —
— Auto Clock Set has not been performed correctly by Auto
Set Up or Preset Download.
OR
— you want to change Just Clock setting. (墌“Just Clock” in
the left column)
APress we to select
“INITIAL SET UP”, then
press ENTER.
BPress we to select
“CLOCK SET”, then press
ENTER.
DR-M10EK_01.book Page 104 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
105
Filename [DR-M10EK_11Subsidiary.fm]
Page 105 February 27, 2004 9:47 am
DSet Just Clock.
The default setting is “OFF”.
APress rt to select “JUST CLOCK”, then press ENTER.
BPress rt to set to the desired mode, then press
ENTER.
●For the Just clock function, refer to “Just Clock” on page 104.
●If you set to “OFF”, you can disregard the next step as you
won’t be able to receive regular clock adjustments.
ESet the source channel position for clock
data.
The unit is preset to receive clock setting and adjustment
data from channel position 1.
APress rt to select “TV PROGRAMME”, then press
ENTER.
BPress rt to set the channel position to the number
representing the station transmitting clock setting data,
then press ENTER.
FStart the clock operation.
Press SET UP.
NOTES:
●Just Clock (when set to “ON”) adjusts the unit’s built-in clock
every hour, except for 23:00, 0:00, 1:00 and 2:00.
●Just Clock is not effective when:
— the unit’s power is on.
— the unit is in the Timer mode.
— a difference of more than 3 minutes exists between the
built-in clock’s time and the actual time.
— the unit is in the Automatic Satellite Programme Recording
mode. (墌pg. 65)
— the unit is in the Power Save mode. (墌pg. 95)
— “L-2 SELECT” is set to “SAT VIDEO” or “SAT S-VIDEO”.
(墌pg. 85)
●If Just Clock is set to “ON”, the unit’s clock is automatically
adjusted at the start/end of Summer Time.
●Just Clock may not function properly depending on the
reception condition.
DR-M10EK_01.book Page 105 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_11Subsidiary.fm]
Masterpage:Left+
106
Page 106 February 27, 2004 9:47 am
SUBSIDIARY SETTINGS (cont.)
Format A Disc
Some DVD-RAM/RW discs are unformatted.
Format the disc when you use an unformatted disc or you want
to delete all recordings and data on the disc.
Format a DVD-RAM disc
AAccess the Main Menu screen.
Press SET UP.
BAccess the “UTILITY” screen.
CFormat the disc.
APress rt to select “FORMAT”, then press ENTER.
Press we to select “YES”, then press ENTER when
“DISC WILL BE FORMATTED” appears on the TV
screen.
BPress we to select “OK”, then press ENTER when
“DISC FORMATTING WAS SELECTED” appears on
the TV screen.
Format a DVD-RW disc
AFormat the disc.
APress rt to select “FORMAT”, then press ENTER.
Press we to choose “VR MODE” or “VIDEO MODE”,
then press ENTER when “DISC WILL BE
FORMATTED” appears on the TV screen.
“VR MODE”: To be chosen when you want to
record, erase, or edit data on the
disc repeatedly.
“VIDEO MODE”:To be chosen when you want to
erase all the data on the disc once
played back to record new data, or
play the disc on other DVD players.
BPress we to select “YES”, then press ENTER when
“DISC WILL BE FORMATTED IN VR MODE/VIDEO
MODE” appears on the TV screen.
NOTES:
●It is impossible to format Version 1.0 DVD-RW discs in Video
mode.
●It is impossible to format DVD-R discs.
●All the programmes on a disc will be deleted once the disc is
formatted even if they are protected titles. (墌pg. 70, “Protect
title”)
A
TTENTI
O
N:
●When a disc is formatted, all recordings and data are
erased. It is impossible to restore them.
●Never turn off the unit or disconnect the mains power cord
while “NOW FORMATTING...” is displayed on the TV
screen.
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
●Load a DVD-RAM/RW disc to format.
DVDTV
DVD
TIMER
PROG/CHECK
NEXTPREVIOUS
PAUSEREC
REC MODE LIVE CHECK
SET UP DISPLAY
ON SCREEN
OPEN/
CLOSE
AUDIO SUBTITLE ANGLE
PROGRESSIVE
SCAN
SLOWSLOW PLAY/SELECT
STOP/
CLEAR
NAVIGATIONTOP MENU
RETURN
ENTER
MENU
STANDBY/ON
ABC
JKLGHI MNO
TUVPQRS WXYZ
AUXCANCEL
MEMO/MARK
DEF
CABLE/SAT
PR
SAT
#
SHOW VIEW/
VIDEO Plus
+
TV/CBL/SAT
TV TV AV
VIDEO
TV%
rtwe
ENTER
SET UP
DVDTV
CABLE/SAT
APress rt w e to select
“DVD SET UP”, then press
ENTER.
BPress we to select
“UTILITY”, then press
ENTER.
Perform steps A to B of “Format a DVD-RAM disc” on the
above before continuing.
DR-M10EK_01.book Page 106 Friday, February 27, 2004 10:07 AM
Masterpage:Right-No-Heading
107
Filename [DR-M10EK_11Subsidiary.fm]
Page 107 February 27, 2004 9:47 am
Finalise A Disc
Finalising DVD-R/RW discs recorded on this unit makes it
possible for the discs to be played back on other DVD players.
DVD-RW discs are finalised in the mode that the discs were
formatted, enabling playback on compatible DVD players.
Titles input in the Library Database DVD Navi are registered as
titles in the DVD menu. (墌pg. 32, 70)
Before finalising
●It is possible to record on a blank space.
●It is possible to enter a programme title. (墌pg. 70, “Modify
Programme Name”)
●It is possible to delete programmes. (墌pg. 71, “Delete
programme”)
●It is impossible to overwrite recorded areas of DVD-R discs.
●Available recording capacity does not increase even if a
recorded programme is deleted from a DVD-R disc.
●It is impossible to record or edit DVD-R/RW discs recorded on
other devices even if they have not been finalised.
After finalising (For DVD-R/RW (Video mode) discs)
●Video and audio that have been recorded by then are recorded
in conformity to the DVD Video standard, enabling you to
play back the discs as DVD VIDEO discs. (墌pg. 7, “Discs for
Playback Only”)
●Although DVD-R/RW discs finalised on this unit become
playable on DVD players compatible with DVD-R/RW discs,
some discs still may not play, for which JVC cannot take
responsibility.
●Marked points marked before finalising will be deleted, and
programmes will be divided automatically into “chapters”
approximately every 5 minutes. (墌pg. 34, “Marking
positions to play again later”)
●Depending on the DVD players and DVD-R/RW discs used,
and on the conditions of recording, it may not be possible to
play back the discs. In this case, play back the discs on this
unit.
●Additional recordings become impossible.
Finalise a DVD-R/RW disc
AFinalise the disc.
APress rt to select “FINALISE”, then press ENTER.
Press we to select “YES”, then press ENTER when
“DISC WILL BE FINALISED” appears on the TV screen.
BPress we to select “OK”, then press ENTER when
“FINALISING WILL MAKE DISC READ-ONLY”
appears on the TV screen.
BReturn to the normal screen.
Press SET UP.
●Menu screen is cleared.
●Once a DVD-R/RW (Video mode) disc has been finalized, the
displays for original and play list do not appear. Only display
for library appears.
●Once a DVD-RW (VR mode) disc has been finalised, it can be
played on DVD players compatible with VR mode.
Cancel the finalisation of a DVD-RW
disc
ACancel the disc finalisation.
APress rt to select “CANCEL DISC FINALISATION”,
then press ENTER.
BPress we to select “OK”, then press ENTER when
“CANCEL DISC FINALISATION” appears on the TV
screen.
BReturn to the normal screen.
Press SET UP.
●When the disc finalisation is cancelled, the mode in which the
disc was formatted is restored, making the disc recordable.
(墌pg. 8, 106)
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
●Load a DVD-R/RW disc to finalise.
Perform steps A to B of “Format a DVD-RAM disc”
(墌pg. 106) before continuing.
Load a DVD-RW disc to cancel the disc finalisation, and
perform steps A to B of “Format a DVD-RAM disc”
(墌pg. 106) before continuing.
DR-M10EK_01.book Page 107 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_11Subsidiary.fm]
Masterpage:Left+
108
Page 108 February 27, 2004 9:47 am
SUBSIDIARY SETTINGS (cont.)
Scan Mode Set
You can select the scan mode from two modes: Interlaced
scan mode which is used in the conventional TV system,
and Progressive scan mode which enables reproduction
of higher-quality images. For details, refer to
“GLOSSARY” (墌pg. 113).
ASet the scan mode.
Press PROGRESSIVE SCAN for 3 or more seconds.
●Video output indicator ( ) lights on the front display panel if
Progressive scan mode has been established. (墌pg. 14)
●Each press of PROGRESSIVE SCAN for 3 or more seconds
switches the scan mode.
NOTES:
●When the progressive mode is set, be sure to set “L-1
OUTPUT” to “COMPONENT”. (墌pg. 84, “L-1 Output and
L-1 Input Setting (L-1 OUTPUT and L-1 INPUT)”) Progressive
scan is output only from COMPONENT VIDEO OUT
connector.
●Interlaced scan mode is the setting at your purchase.
●When Progressive scan mode is engaged, no video signal is
output from S-VIDEO OUT connector and L-1 IN/OUT
connector.
●Interlaced scan mode might be suitable depending on video
material.
●Scan mode cannot be set while menu screen is displayed.
Tray Lock
You can lock the disc tray to prohibit the unwanted disc
ejection by children.
ALock the disc tray.
While the unit is turned off, press and hold 8, then press
x on the unit. “LOCK” appears on the front display
panel.
●If you try to eject the discs, “LOCK” appears and indicates that
tray is locked.
To unlock tray
While the unit is turned off, press and hold 8, then press
x on the unit. “UNLOCK” appears on the display panel.
●Turn on the unit.
●Turn on the TV and select the AV mode.
●Slide the TV/CABLE/SAT/DVD switch to DVD.
A
TTENTI
O
N:
Your TV needs to be compatible with PAL Progressive.
●Turn off the unit.
DR-M10EK_01.book Page 108 Friday, February 27, 2004 10:07 AM
Masterpage:Right0
109
Filename [DR-M10EK_11Subsidiary.fm]
Page 109 February 27, 2004 9:47 am
TROUBLESHOOTING
Before requesting service for a problem, use this chart and see if you can solve the trouble yourself. Small problems are
often easily solved, and this can save you the trouble of sending your unit off for repair.
GENERAL
PLAYBACK
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
1. No power is supplied to the unit. ●The AC power plug is disconnected from
the mains.
Connect the AC power plug to the mains
securely. (墌pg. 18)
2. The channel cannot be changed. ●Recording or Live Memory recording is
in progress.
Press 9 to pause recording, change the
channel, then press 4 to resume
recording.
3. The remote control does not operate
the unit.
●The setting of the remote control code is
inappropriate.
Set the same remote control code (1, 2, 3,
or 4) on both the unit and the remote
control. (墌pg. 87)
●The batteries are discharged. Replace the dead batteries with new ones.
4. Dubbing from the external equipment
is not possible.
●The setting of the input channel position
is inappropriate.
Select the input channel position (“F-1”,
“L-1”, or “L-2”) that corresponds to the
input terminal connected to the external
equipment. (墌pg. 83)
5. The on-screen display superimposed
on the programme played back/
received on this unit is recorded when
you dub the programme to an external
recording equipment.
—
Set “SUPERIMPOSE” to “OFF”.
(墌pg. 95)
6. The remote control does not work
properly. —Remove the batteries, wait for 5 minutes or
more, then load the butteries again.
●The batteries are discharged. Replace the dead batteries with new ones.
7. The unit does not operate. ●There are cases when the operation is
prohibited on the disc. —
●Lightning or static electricity may cause
malfunction of the unit.
Press 1 to turn the power off, then press
the button again to turn the power on.
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
1. Images do not appear on the TV
screen.
●The TV is not set to the AV mode. Set the TV to the AV mode.
●When interlace scanned programme is
played back, progressive scan mode is
selected.
Press and hold PROGRESSIVE SCAN until
disappears from the front display
panel.
2. Playback dose not start or stop
immediately after playback is started by
pressing 4.
On the front display panel, “NO DISC”
appears.
●The disc is loaded upside down. Place the disc on the disc tray with the
playback surface facing downward.
(墌pg. 10)
●A disc not being compatible with the
unit is loaded.
Load a playable disc on the unit.
(墌pg. 6, 7)
●A dirty disc is loaded. Clean the disc. (墌pg. 10)
●Defective disc is loaded. Replace the warped or scratched disc with
a normal one.
3. Images are blurred or distorted when
you start High-Speed Search. —
Images are blurred or distorted at the point
where the playback speed changes and
this is not a malfunction of the unit.
4. Playback does not start.
—
Playback does not start for approximately
30 seconds after recording is stopped and
this is not a malfunction of the unit.
5. Playback does not start when you
select a title or a chapter.
●The Parental Lock is engaged and the
disc is rated higher than the set level.
Release the Parental Lock temporarily or
change the set level. (墌pg. 49)
DR-M10EK_01.book Page 109 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_11Subsidiary.fm]
Masterpage:Left+
110
Page 110 March 16, 2004 2:22 pm
TROUBLESHOOTING (cont.)
RECORDING
INITIALIZING
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
1. The desired programme cannot be
recorded.
●The channel position does not
correspond to that in the receiving area.
Set the correct channel position for the
receiving broadcast. (墌pg. 98)
2. Recording and editing cannot be
made.
●No disc or a disc not being compatible
with the unit is loaded.
Load a recordable disc on the unit.
(墌pg. 6)
●The disc loaded is not formatted. Format the disc. (墌pg. 106)
●A finalised DVD-R disc is loaded. Recording and editing cannot be made on
finalised discs. (墌pg. 107) Load a
recordable disc on the unit.
●The disc is full or does not have enough
space for the programme to be recorded.
Clear unnecessary programmes on the
disc or load a blank disc. (墌pg. 71)
3. Timer programming cannot be made. ●Date and time is not correct. Set date and time correctly. (墌pg. 104)
4. Timer programming recording does not
start.
●Power failure occurred before the timer
programmed recording starts.
Check the timer programming. (墌pg. 63)
5. VIDEO Plus+ Timer Programming
cannot be made.
●Date and time set on the unit is not
correct.
Set date and time correctly. (墌pg. 104)
●The channel position does not
correspond to that in the receiving area.
Set the correct channel position for the
receiving broadcast. (墌pg. 98)
6. Automatic Satellite Programming
recording does not start.
●The satellite receiver is not connected
properly to this unit.
Connect the satellite receiver to the L-2
IN/DECODER connector properly.
(墌pg. 90)
7. On the front display panel, “– –:– –”
appears.
●Power failure occurred. Set date and time correctly. (墌pg. 104)
8. “PROGRAM FULL” appears on the TV
screen during timer programming.
●Eight programmes have already been
timer programmed.
Clear unnecessary programmes on the
unit, then try timer programming again.
(墌pg. 63)
9. The disc space does not increase when
recorded programmes are cleared.
●The PC’s data recorded on a DVD-RAM
drive cannot be cleared on this unit.
Format the disc. (When the disc is soiled,
wipe the disc with a soft dry cloth before
formatting.) (墌pg. 10, 106)
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
1. Malfunction occurs on the unit.
—
Press 1 to turn off the unit, press and
hold 1, then press 8 for two seconds or
more.
2. The Disc Tray doesn’t open.
—
Take out the disc in following ways.
●connect and disconnect the power cord
from the mains outlet.
●press and hold x on the unit until the
disc tray opens. (it will take about 30
sec.)
●close the disc tray by pressing x after
taking out the disc. (the main power
shuts down)
A
TTENTI
O
N:
This unit contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the
unit off and unplug the mains power cord. Then plug it in again and turn the unit on. Take out the disc. After checking the disc,
operate the unit as usual.
DR-M10EK_11Subsidiary.fm Page 110 Tuesday, March 16, 2004 2:22 PM
Masterpage:Right-No-Heading
111
Filename [DR-M10EK_11Subsidiary.fm]
Page 111 February 27, 2004 5:58 pm
ON-SCREEN MESSAGES
MESSAGE DESCRIPTION
MEMORY IS FULL
NOTHING MORE CAN BE REGISTERED IN THE LIBRARY
IF YOU DELETE UNNECESSARY TITLE INFORMATION,
YOU CAN THEN REGISTER ADDITIONAL INFORMATION
The memory is full for registration for the Navigation system. The
recording cannot be started even though the capacity for the
recording is enough. (墌pg. 71)
AVAILABLE MEMORY IS LOW
SOON YOU WILL NO LONGER BE ABLE
TO REGISTER INFORMATION IN THE LIBRARY
IF YOU DELETE UNNECESSARY TITLE INFORMATION,
YOU CAN THEN REGISTER ADDITIONAL INFORMATION
The remaining capacity of the memory is not enough for
registration for the Navigation system. The recording cannot be
started even though the capacity for the recording is enough.
(墌pg. 71)
DISC NOT REGISTERED IN THE LIBRARY
REGISTER DISC? A disc that is not registered in the library has been inserted.
Register the disc as necessary. (墌pg. 77)
INSERT DISC #XXXX Appears when a title that has been selected in the library is not
contained in the loaded disc. (墌pg. 76)
CAN NOT RECORD OR MAKE PLAY LIST
DELETE UNWANTED TITLES
●Recording and/or editing cannot be performed with a loaded
DVD-RAM disc.
●The number of titles exceeds 99.
●The number of play lists exceeds 999.
SET CLOCK BEFORE TIMER PROGRAMMING To set the timer programme, the clock must be set in advance.
(墌pg. 104)
PROGRAMME FULL
DELETE UNWANTED TIMER PROGRAMME You can programme this unit to timer-record as many as 8
programmes. To programme more, you need to cancel a timer
programme already set. (墌pg. 63)
CAN NOT SET DISC TIMER PROGRAMMING WITH THIS DISC
PREPARE A FORMATTED DISC AS DESCRIBED BELOW
DVD-RAM
DVD-RW (VR MODE)
On-Disc Timer Programming has been attempted when a disc
that is not compatible with the function is loaded. (墌pg. 60)
NO DISC INSERTED On-Disc Timer Programming has been attempted when a disc is
not loaded, or loaded upside down. (墌pg. 10, 60)
DISC NOT RECORDABLE
INSERT RECORDABLE DISC When a playback-only disc or a finalised disc is loaded, 7 has
been pressed. (墌pg. 7, 107)
PLUSCODE NO. ERROR
CONFIRM PLUSCODE NO. THEN RETRY An invalid PlusCode number has been input. (墌pg. 56)
GUIDE PROGRAMME IS NOT SET
SELECT CHANNEL YOU WANT TO RECORD To set the timer programme using the VIDEO Plus+ system, the
Guide Program number must be set in advance. (墌pg. 97)
CAN NOT SET SHOWVIEW TIMER PROGRAMMING DURING
TIMER RECORDING OR INSTANT TIMER RECORDING
CANCEL TIMER RECORDING OR
INSTANT TIMER RECORDING, THEN
ENTER THE SHOWVIEW CODE AGAIN
Appears when you tried to input a PlusCode number during
timer recording or instant timer recording.
REGION CODE ERROR
CHECK DISC A disc loaded cannot be played back on this unit since the
region number of the disc does not match that of the unit.
(墌pg. 7)
UNREADABLE DISC
CHECK DISC When an incompatible disc is loaded, 4 has been pressed.
(墌pg. 7)
COULD NOT FORMAT THE DISC
CHECK THE DISC Formatting is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (墌pg. 10, 106)
COULD NOT FINALISE THE DISC
CHECK THE DISC Finalising is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (墌pg. 10, 107)
COULD NOT CANCEL DISC FINALISATION
CHECK THE DISC Cancelling disc finalisation is not complete since the disc may
be dirty or damaged. Take out the disc, clean it and retry.
(墌pg. 10, 107)
DR-M10EK_11Subsidiary.fm Page 111 Friday, February 27, 2004 5:59 PM
Filename [DR-M10EK_11Subsidiary.fm]
Masterpage:Left+
112
Page 112 February 27, 2004 9:47 am
TROUBLESHOOTING (cont.)
ON-SCREEN MESSAGES (cont.)
MESSAGE DESCRIPTION
PRESS [STOP] AGAIN TO STOP RECORDING During Live Memory playback, 8 has been pressed. (墌pg. 40)
TIMER RECORDING COMPLETED Timer recording has finished during Live Memory playback.
PLAYBACK WILL STOP
THEN TIMER RECORDING WILL START Timer recording finished during Live Memory playback, then the
next timer recording is about to begin while playback continues.
COPY PROHIBITED
CAN NOT RECORD
●An attempt has been made to record copy-protected contents.
●An attempt has been made to record copy-once contents on a
disc that is not CPRM compatible, such as DVD-R.
COPY PROHIBITED
CAN NOT PLAY The unit has detected invalid contents at the start or in the
middle of playback.
THE i.LINK DEVICE THAT YOU HAVE CONNECTED IS NOT
RECOGNIZED
MAKE SURE THAT THE DEVICE IS CONNECTED PROPERLY
AND POWERED ON
An attempt has been made to start DV dubbing when a digital
video camera is not properly connected to the unit.
Check the connection. (墌pg. 80)
DR-M10EK_01.book Page 112 Friday, February 27, 2004 10:07 AM
Masterpage:Right0
113
Filename [DR-M10EK_11Subsidiary.fm]
Page 113 February 27, 2004 9:47 am
GLOSSARY
8Aspect ratio
The ratio of vertical and horizontal sizes of a displayed image.
The horizontal vs. vertical ratio of conventional TVs is 4:3, and
that of wide-screens is 16:9.
8Chapter
Refers to individual chapters included in a title.
8Composite video signal
Refers to video signal comprised of three kinds of signals
combined: an image signal made up of luminance and
chrominance signals using the frequency multiplication
technique; burst signal providing the basis for colour
reproduction; and synchronization signal.
8Component video signal
A video signal system where parts of information necessary for
reproducing image signal comprised of the three primary
colours of light are transmitted via separate signal lines. Types of
signal, such as R/G/B, Y/PB/PR, etc., are available.
8Disc menu
A screen display prepared for allowing selection of images,
sounds, subtitles, multiangles, etc. recorded on a DVD disc.
8Dolby Digital (AC-3)
A six-channel system consisting of left, centre, right, left rear,
right rear and LFE (Low-Frequency Effect channel, for use with a
sub-woofer) channels. All processing is done in the digital
domain.
Not all Dolby Digital discs contain six (5.1) channels of
information.
8Down-mix
Internal stereo mix of multichannel surround audio by a DVD
player. The down-mix signals are output from stereo output
connectors.
8DTS
A Digital Surround audio encoding format configured with six
(5.1) channels, similar to Dolby Digital. It requires a decoder,
either in the player or in an external receiver. DTS stands for
Digital Theater Systems.
Not all DTS discs contain six (5.1) channels of information.
8Interlaced scan
In the conventional video system, a picture is shown on the
display monitor in two halves. The Interlaced scan system places
lines of the second half of the picture in-between lines of the first
half of the picture.
8JPEG
A still-picture data compression system proposed by the Joint
Photographic Expert Group, which features small decrease in
image quality in spite of its high compression ratio.
8Letter box
A method of displaying wide images like movies in the centre of
a 4:3 TV screen with no part of the image deleted, by placing
black bands on the top and bottom of the screen. This name has
resulted from the screen form looking literally like a letter box.
8Linear PCM (PCM: Pulse Code Modulation)
A system for converting analog sound signal to digital signal for
later processing, with no data compression used in conversion.
8MP3
A file format with a sound data compression system. “MP3” is
the abbreviation of Motion Picture Experts Group 1 (or MPEG-1)
Audio Layer 3. By using MP3 format, one CD-R/RW can contain
about 10 times as much data volume as a regular CD can.
8MPEG
A family of Standards for compressing audio-visual information.
“MPEG” standards include MPEG-1, MPEG-2 and MPEG-4.
Video CD/SVCD and MP3 are based on MPEG-1, while DVD is
based on MPEG-2. MPEG stands for Moving Picture coding
Experts Group.
8Multiangle
By recording multiple scenes progressing at the same time in a
single title, the user can select view angles. This feature is called
the multiangle function.
8Multichannel
DVD is specified to have each sound track constitute one sound
field. Multichannel refers to a structure of sound tracks having
three or more channels.
8Multilanguage
When a title is created to cope with multiple languages, it is
generally called a multilanguage title.
8NTSC (National television system committee)
A black and white and colour television system format used in
the U.S.A., Canada, Mexico and Japan.
8PAL (Phase Alternation by Line)
A colour television system format used extensively in Western
Europe.
8Parental Lock
A feature of this system to automatically determine whether or
not to reproduce particular DVD software by comparing its
parental lock level (a measure of undesirability of scenes, etc.
from educational viewpoint) set for the software beforehand
with that set on this system by the user; if the software’s level is
less restrictive than the user-set level, it will be reproduced.
8Playback control (PBC)
Refers to the signal recorded on Video CD/SVCDs for controlling
reproduction. By using menu screens recorded on a Video CD/
SVCD that supports PBC, you can enjoy interactive-type
software as well as software having a search function.
8Progressive scan
Progressive scan displays all the horizontal lines of a picture at
one time, as a single frame. This system can convert the
interlaced video from DVD into progressive format for
connection to a progressive display. It dramatically increases the
vertical resolution.
8Region Code
A system for allowing discs to be played back only in the regions
designated beforehand. All the countries in the world are
grouped into six regions, each region being identified by a
specified Region Code (or region number). If the Region Code
given to a disc includes a numeral which matches one in the
Region Code of a player, the player can play back the disc.
8Sampling frequency
Frequency of sampling data when analog data is converted to
digital data. Sampling frequency numerically represents how
many times the original analog signal is sampled per second.
8Surround
A system for creating three-dimensional sound fields full of
realism by arranging multiple speakers around the listener.
8Transfer rate
The rate of transferring digital data. Usually the measure is in
baud per second. The DVD system applies a variable transfer
rate system for high efficiency.
DR-M10EK_01.book Page 113 Friday, February 27, 2004 10:07 AM
Filename [DR-M10EK_11Subsidiary.fm]
Masterpage:Left0
114
Page 114 February 27, 2004 9:47 am
SPECIFICATIONS
GENERAL
Power requirement : AC 220 V – 240 Vd, 50 Hz/60 Hz
Power consumption
Power on : 33 W
Power off : 17.6 W
Temperature
Operating : 5°C to 40°C
Storage : –20°C to 60°C
Operating position : Horizontal only
Dimensions (WxHxD)
: 435 mm x 70 mm x 346 mm
Weight : 4.5 kg
VIDEO/AUDIO
Recordable disc : DVD-RAM 12 cm (4.7 GB/9.4 GB)
DVD-RAM 8 cm (1.4 GB/2.8 GB)
DVD-R (12 cm: 4.7 GB,
8 cm: 1.4 GB for General Ver. 2.0)
DVD-RW (4.7 GB for Ver. 1.0/1.1)
Recording format
DVD-RAM : DVD Video Recording format
DVD-R : DVD-Video format
DVD-RW : DVD-Video format, DVD Video
Recording format
Recording time
Maximum 8 hours (with 4.7 GB disc)
(XP) : Approx. 1 hour
(SP) : Approx. 2 hours
(LP) : Approx. 4 hours
(EP) : Approx. 6 hours
(FR) : Approx. 1 hour – 8 hours
Playable disc : DVD-RAM 12 cm (4.7 GB/9.4 GB)
DVD-RAM 8 cm (1.4 GB/2.8 GB)
DVD-R (12 cm: 4.7 GB,
8 cm: 1.4 GB for General Ver. 2.0)
DVD VIDEO, DVD-RW (4.7 GB)
Music CD (CD-DA)
Video CD
Super Video CD (SVCD)
CD-R/RW (CD-DA, Video CD/
SVCD formatted discs)
Audio recording system
: Dolby Digital (2 ch)
Linear PCM (XP mode only)
Video recording compression system
: MPEG2 (CBR/VBR)
Input/Output
S-video input
Y : 0.8 – 1.2 Vp-p, 75 ohms
C : 0.2 – 0.4 Vp-p, 75 ohms
S-video output
Y : 1.0 Vp-p, 75 ohms
C : 0.3 Vp-p, 75 ohms
Video input : 0.5 – 2.0 Vp-p, 75 ohms (pin jack)
Video output : 1.0 Vp-p, 75 ohms (pin jack)
Audio input : –8 dB, 50 kilohms (pin jack)
Corresponding to mono (left)
Audio output : –8 dB, 1 kilohms (pin jack)
i.Link : 4-pin for DV input
Component video output
Y : 1.0 Vp-p, 75 ohms
PB/PR: 0.7 Vp-p, 75 ohms
Corresponding to copy protection
Optical : –18 dBm, 660 nm
Coaxial : 0.5 Vp-p, 75 ohms
Corresponding to Dolby Digital and
DTS Digital Surround
Bit stream
Selectable in digital audio output
setting menu
TUNER/TIMER
Signal system : PAL-type colour signal and CCIR
monochrome signal, 625 lines
50 fields
TV channel storage capacity
: 99 positions (+AUX position)
Tuning system : Frequency synthesized tuner
Channel coverage : VHF 44.5 MHz – 143 MHz/
143 MHz – 470 MHz
UHF 470 MHz – 862 MHz
Memory backup time
: Approx. 60 min.
ACCESSORIES
Provided accessories
: RF cable,
21-pin SCART cable,
Satellite Controller,
Infrared remote control unit,
“AA” battery x 2
Specifications shown are for SP mode unless otherwise
specified.
E.& O.E. Design and specifications subject to change without
notice.
DR-M10EK_01.book Page 114 Friday, February 27, 2004 10:07 AM
Masterpage:Right0
115
Filename [DR-M10EK_01IX.fm]
Page 115 February 27, 2004 6:00 pm
LIST OF TERMS
A
A-B Repeat Playback ............................................ 45
Adjusting the picture quality .................................. 47
Angle Selection .................................................... 35
Audio Channel Selection ....................................... 36
Audio Language/Sound Selection ........................... 35
AUDIO OUTPUT ................................................. 93
Auto Channel Set ................................................. 98
C
Check, cancel and change programmes .................. 63
D
Delete programme ............................................... 71
Disc menu .......................................................... 32
Discs for Playback Only .......................................... 7
DISPLAY SET ....................................................... 95
DVD menu ......................................................... 32
F
File Structure of Discs ............................................. 8
Free Rate Function ............................................... 55
G
Guide Program Number ........................................ 97
H
High-Speed Search ............................................... 33
I
Instant Timer Recording (ITR) ................................. 54
J
Just Clock .......................................................... 104
L
Letter Box ........................................................... 25
Library Database DVD Navi .................................. 66
Live Memory ....................................................... 37
M
Manual Channel Set ............................................. 99
Marking positions to play again later ....................... 34
Menu/Audio/Subtitle Language Set ......................... 26
O
On-Disc Timer Programming ................................. 60
One Touch Replay ............................................... 41
On-screen Language Set ........................................ 26
P
Pan&Scan ............................................................ 25
Parental Lock ....................................................... 49
Play List .............................................................. 72
Play Set Up Menu ................................................. 42
Playback Control (PBC) ......................................... 36
Programme Playback ............................................ 48
R
Random Playback ................................................. 48
Recordable/playable discs ....................................... 6
Recording Medium and Format ................................ 8
Recording Resume Function ................................... 53
RECORDING SET ................................................. 94
Recording Speed .................................................. 54
Region Number ...................................................... 7
Register disc ........................................................ 77
Repeat Playback ................................................... 44
Resume Function .................................................. 33
S
Scan Mode Set ................................................... 108
Select the switching interval of the slide show .......... 48
Setting the progressive mode .................................. 47
Simulated Surround Effect ...................................... 46
Skip Search .......................................................... 33
Slow Motion ........................................................ 33
Still Picture/Frame-By-Frame Playback ..................... 33
Subtitle Selection .................................................. 35
T
Time Search ......................................................... 46
Top menu ............................................................ 32
TV Station Channel Number Guide ....................... 103
U
Unplayable Discs ................................................... 7
V
PDC Recording .................................................... 59
DR-M10EK_01IX.fm Page 115 Friday, February 27, 2004 6:00 PM
PROG
VCR Plus+
PREVIOUS
REC
REC MODE LIVE
SET UP DIS
AUDI O SUB
SLOW P
S
TOP MENU
MENU
TV
MUTING T
VID
A
J
GHI
TPQRS
ACANCEL
DBS
Filename [DR-M10EK_13Cov4.fm]
EN
Page 116 March 16, 2004 2:25 pm
DR-M10
Printed in Germany
0304MNH-ID-VE
DR-M10EK_13Cov4.fm Page 116 Tuesday, March 16, 2004 2:25 PM

Navigation menu