JVC KD AVX11A AVX11 Installation [A] User Manual LVT1657 006A

KD-AVX11A KD-AVX11A INSTALLATION MANUAL LVT1657-006A

User Manual: JVC KD-AVX11A KD-AVX11A English, INSTALLATION MANUAL

Open the PDF directly: View PDF PDF.
Page Count: 4

9.5 mm
2 mm
KD-AVX11
Installation/Connection Manual
LVT1657-006A
[A]
0107MNMMDWJEIN
EN
©2007 Victor Company of Japan, Limited
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does
not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
WARNINGS
• DO NOT install any unit and wire any cable in locations where;
– it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident.
– it may obstruct the operation of safety devices such as air bags, as this may result in a fatal accident.
– it may obstruct visibility.
• DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic accident.
• The driver must not watch the monitor while driving.
If the driver watches the monitor while driving, it may lead to carelessness and cause an accident.
• If you need to operate the unit while driving, be sure to look around carefully.
• If the parking brake is not engaged, “Parking Brake” appears on the monitor, and no playback picture
will be shown.
– This warning appears only when the parking brake wire is connected to the parking brake system built
in the car.
J
Rubber cushion
F
Crimp connectors
G
Washer (ø5)
H
Lock nut (M5)
I
Mounting bolt—
M5 x 20 mm
C
Sleeve
E
Power cord
Parts list for installation and connection
The following parts are provided for this unit. After checking them, please set them correctly.
K
Handles
L
Remote controller
A / B
Hard case/Control panel
M
Battery
D
Trim plate
*1 When you stand the unit, be careful not
to damage the fuse on the rear.
Do the required electrical connections.
Bend the appropriate tabs to hold the
sleeve firmly in place.
N
Reverse gear signal extension cord
Do not block the fan.
1
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
• Make sure not to block the fan on the rear panel to maintain proper ventilation when installed.
Required space for installation
• You cannot install the unit on the car which has any obstacles in the space indicated below.
Control panel
Trim plate is detached on this
illustration for explanation.
Dashboard
Caution when installing
Fit the unit into the mounting sleeve by using four corners of the
trim plate.
• DO NOT press the panel (shaded in the illustration).
INSTALLATION (IN-DASH MOUNTING)
Install-1_KD-AVX11[A].indd 1Install-1_KD-AVX11[A].indd 1 07.1.8 11:56:04 AM07.1.8 11:56:04 AM
2
When using the optional stay When installing the unit without using the sleeve
In a Toyota car for example, first remove the car radio and install the unit in its place.
Screw (option)
Stay (option)
Fire wall
Dashboard
Bracket *2
*2 Not included for this unit.
Flat type screws—M5 x 8 mm *2
Bracket *2
Install the unit at an angle of less than 30˚.
Note: When installing the unit on the mounting bracket, make sure to use the 8 mm-long
screws. If longer screws are used, they could damage the unit.
Removing the unit
Before removing the unit, release the rear section.
Insert the two handles, then pull them as
illustrated so that the unit can be removed.
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all
electrical connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after installation.
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio
dealer.
• It is recommended to connect to the speakers with maximum power of more than 50 W (both at
the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50
W, change “Amplifier Gain” setting to prevent the speakers from being damaged (see page 40 of the
INSTRUCTIONS).
• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.
Heat sink
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the
unit will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in
your car.
Connecting the parking brake lead
Parking brake lead (light green)
To metallic body or chassis
of the car
Parking brake switch (inside the car)
Parking brake
Pocket
Flat type screws—M5 x 8 mm *2
A
Connect the parking brake lead to the parking brake system built in the car.
REVERSE GEAR SIGNAL
KD-AVX11
Connecting the REVERSE GEAR SIGNAL lead (for rear view camera)
Locate the reverse lamp lead in the trunk.
To reverse lamp
Reverse lamp lead
Reverse lamp lead
To car battery Purple with white stripe
Reverse lamps
B
ELECTRICAL CONNECTIONS
Install-1_KD-AVX11[A].indd 2Install-1_KD-AVX11[A].indd 2 07.1.8 11:56:13 AM07.1.8 11:56:13 AM
VIDEO IN
LINE IN
KD-AVX11 DIGITAL OUT
VIDEO OUT
Connections for external component playback
A
Video cord (not supplied)
External component
Camcorder, rear view
camera, etc.
Typical connections
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
1 Connect the colored leads of the power cord in the order specified in the illustration below.
2 Connect the antenna cord.
3 Finally connect the wiring harness to the unit.
3
External monitor
Audio/video control amplifier or the decoder
compatible with the multichannel digital sources
See page 49 of the
INSTRUCTIONS.
SUBWOOFER
(see diagram )
15 A fuse
Rear ground
terminal
LINE OUT (FRONT/REAR)
(see diagram )
To an external component (see
diagram )
*3 Not included for this unit
Ignition switch
Fuse block
To metallic body or chassis of the car
To a live terminal in the fuse block connecting to the car battery (bypassing
the ignition switch) (constant 12 V)
To an accessory terminal in the fuse block
To car light control switch
To cellular phone system
To parking brake (see diagram )
Black
Yellow *4
Red
Blue with white stripe
Orange with white stripe
Brown
Light green
LINE IN (see diagram )
VIDEO IN (see diagram )
REVERSE GEAR SIGNAL
(see diagram )
VIDEO OUT (see diagram )
To the remote lead of other equipment (200 mA max.)
*4
Before checking the operation of this unit prior to
installation, this lead must be connected, otherwise power
cannot be turned on.
DIGITAL OUT (see diagram )
To automatic antenna if any (250 mA max.)
Blue
White with black
stripe
White Gray with black stripe Gray Green with black stripe Green Purple with black stripe Purple
Left speaker (front) Right speaker (front) Left speaker (rear) Right speaker (rear)
Install-2_KD-AVX11[A].indd 3Install-2_KD-AVX11[A].indd 3 07.1.8 11:59:44 AM07.1.8 11:59:44 AM
KS-U58*9
KD-AVX11
KD-AVX11
LINE OUT (REAR)
SUBWOOFER
LINE OUT (FRONT)
BConnecting the external amplifiers
You can connect amplifiers to upgrade your car
stereo system.
• Connect the remote lead (blue with white
stripe) to the remote lead of the other
equipment so that it can be controlled through
this unit.
• For amplifier only:
– Disconnect the speakers from this unit,
connect them to the amplifier. Leave the
speaker leads of this unit unused.
– You can switch off the built-in amplifier
and send the audio signals only to the
external amplifier(s) to get clear sounds and
to prevent internal heat built-up inside the
unit. See page 40 of the INSTRUCTIONS
(separate volume).
*5 Audio cord (not supplied)
*6 Firmly attach the ground lead to the metallic body or to the chassis of the
car—to the place uncoated with paint (if coated with paint, remove the paint
before attaching the lead). Failure to do so may cause damage to the unit.
C
Other external component
External component
Connecting external components
Remote lead
JVC Amplifier
Remote lead (Blue with white stripe) To the remote lead of other equipment
Y-connector (not supplied for this unit)
Subwoofer
Rear speakers
Front speakers
3.5 mm stereo mini plug
To disconnect the connector
Hold the connector top tightly (1), then pull it out (2).
4
iPod is a trademark of Apple Computer, Inc., registered
in the U.S. and other countries.
JVC Amplifier
JVC Amplifier
JVC CD changer
*8 Line Input Adapter KS-U57 (separately purchased)
*9 Aux Input Adapter KS-U58 (separately purchased)
*10 Audio cord (not supplied)
You can connect external components in series
as shown in the diagram below.
• All the components, adapters or signal cords
need to be purchased separately.
CAUTION:
Before connecting the external components,
make sure that the unit is turned off.
• To use JVC CD changer, Apple iPod or
JVC D. player, set “External Input” to
“Changer/iPod/D. Player” (see page 39 of
the INSTRUCTIONS).
• To use other external components via
KS-U57 or KS-U58, set “External Input”
to “External Input” (see page 39 of the
INSTRUCTIONS)
External component
KS-U57
KS-U58
KS-BTA200*7
KS-PD100
KS-PD500
To KS-BTA200 or KD-AVX11
KS-U57*8
or
or
or
CD changer jack
• The fuse blows.
* Are the red and black leads connected correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
Apple iPod
JVC D. Player
*10
*7 Bluetooth Adapter KS-BTA200
(separately purchased)
External component
TROUBLESHOOTING
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
• Unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• This unit does not work at all.
* Have you reset your unit?
or
Install-2_KD-AVX11[A].indd 4Install-2_KD-AVX11[A].indd 4 07.1.8 11:59:54 AM07.1.8 11:59:54 AM

Navigation menu