JVC KW AV50A AV50[A] Installation Manual User LVT2289 002A
KW-AV50A KW-AV50A INSTALLATION MANUAL (Australia) LVT2289-002A
User Manual: JVC KW-AV50A KW-AV50A English, INSTALLATION MANUAL
Open the PDF directly: View PDF .
Page Count: 2
Download | |
Open PDF In Browser | View PDF |
KW-AV50 Installation/Connection Manual 0911NSHMDWJEIN EN © 2011 JVC KENWOOD Corporation LVT2289-002A [A] This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers. WARNINGS • DO NOT install any unit or wire any cable in a location where; – it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident. – it may obstruct the operation of safety devices such as air bags, as this may result in a fatal accident. – it may obstruct visibility. • DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic accident. • The driver must not watch the monitor while driving. It may lead to carelessness and cause an accident. • If you need to operate the unit while driving, be sure to look around carefully or you may be involved in a traffic accident. • If the parking brake is not engaged, “Parking Brake” appears on the monitor, and no playback picture will be shown. – This warning appears only when the parking brake lead is connected to the parking brake system built in the car. To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit. • Be sure to ground this unit to the car’s chassis again after installation. • Be sure any cable is not caught on the car’s chassis or under seats. Notes on electrical connections: • Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer. • It is recommended to connect speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, changesetting to prevent the speakers from being damaged (see page 42 of the INSTRUCTIONS). • To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape. • The heat sink becomes very hot after use. Be careful not to touch it when removing this unit. • At the time of installation, be sure to fix all wires (wires both from this unit and from the car itself) in a way that any wires cannot come into contact with heat sinks on the rear and side of the unit. INSTALLATION (IN-DASH MOUNTING) The following illustration shows a typical installation. However, you should make adjustments corresponding to your specific car. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits. • If you are not sure how to install this unit correctly, have it installed by a qualified technician. Before installing the unit • When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used, parts could become loose or damaged. • When tightening screws or bolts, be careful not to pinch any connection cord. • Make sure not to block the fan on the rear to maintain proper ventilation when installing the unit. 1 Remove the audio system originally installed in the car, together with its mounting brackets. • Be sure to keep all the screws and parts removed from your car for future use. 2 Attach the mounting brackets (removed from the car) to this unit (see below). • Use flat head screws or round head screws, depending on installation location. • When you need to use round head screws, use the supplied screws and the screws used to attach the metal protection plates to the unit when shipped. 3 Do the required electrical connections. • See “ELECTRICAL CONNECTIONS” on pages 1 and 2. 4 5 Install this unit using the screws removed in step 1. Attach the monitor panel (see below). The following example is for installation in a Toyota car. For more details, consult your JVC car audio dealer. Select the appropriate type fitting to your audio system space. Mounting bracket removed from the car Supplied screws Supplied screws Screws removed from the car in step 1 Heat sink Step 5 When installing the unit in a Nissan car If your Nissan car needs a plate, purchase the plate separately. Plate for use with a Nissan car (not supplied) PRECAUTIONS on power supply and speaker connections: • DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged. • BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car. Parts list for installation and connection The following parts are provided for this unit. If anything is missing, contact your dealer immediately. Main unit Monitor panel and soft case Remote controller Batteries Extension lead Power cord Crimp connector Monitor panel Install the unit at an angle of less than 30˚. 30˚ ELECTRICAL CONNECTIONS RM-RK252 Flat head screws (M5 x 8 mm) Connecting the parking brake lead Round head screws (M5 x 8 mm) Parking brake lead (light green) Parking brake Remove the metal protection plates from the unit before installation. • Keep the round head screws (M5 x 8 mm) used to attach the metal protection plates. You may need to use the screws for installation. Crimp connector Extension lead To metallic body or chassis of the car Parking brake switch (inside the car) Connecting the reverse gear signal lead (for rear view camera) TROUBLESHOOTING • The fuse blows. * Are the red and black leads connected correctly? • Power cannot be turned on. * Is the yellow lead connected? • No sound from the speakers. * Is the speaker output lead short-circuited? • Sound is distorted. * Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common? If necessary, restore the protruding tabs. • When you use screws other than those supplied, use 8 mm-long screws. If longer screws are used, they could damage the unit. • Tighten the screws firmly to prevent the unit from falling off. • Noise interfere with sounds. * Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords? • This unit becomes hot. * Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common? • This unit does not work at all. * Have you reset your unit? Locate the reverse lamp lead in the trunk. Extension lead (not supplied for this unit) Purple with white stripe Crimp connector (not supplied for this unit) To reverse lamps Reverse lamp lead Reverse lamps 1 EN_1-2_KWAVX50[A].indd 1 11.9.14 2:48:31 PM Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit. The leads of the power cord and those of the connector from the car body may be different in color. 1 2 3 See each diagram below. Connect the colored leads of the power cord in the order specified in the illustration below. Connect the antenna cord. Finally connect the wiring harness to the unit. Light green To parking brake (see page 1) PARKING BRAKE Crimp connector (See page 1) REVERSE GEAR SIGNAL 3 CAMERA IN 1 SUBWOOFER OUT Black 1 To metallic body or chassis of the car Yellow *2 Blue Blue with white stripe Fan 5 To the remote lead of other equipment (200 mA max.) Orange with white stripe Fuse block 6 To car light control switch 7 To mobile phone system Brown 10 A fuse Antenna terminal *1 a live terminal in the fuse block connecting to the car battery 2 To (bypassing the ignition switch) (constant 12 V) 3 To an accessory terminal in the fuse block To automatic antenna 4 if any (250 mA max.) Red Rear ground terminal Ignition switch *1 Blue with yellow stripe To the OE remote adapter *3 8 White with black stripe White Gray with black stripe Gray Left speaker (front) A Green with black stripe Green Right speaker (front) C Connecting to the steering wheel remote controller Purple with black stripe Purple Right speaker (rear) Left speaker (rear) Connecting the external components KV-CM10 *1 Rear view camera If your car is equipped with the steering wheel remote controller, you can operate this unit using the controller. For connection, an exclusive remote adapter (not supplied) which matches your car is required. For details, consult the same car audio dealer as where the unit is purchased. CAMERA IN *7 *7 OE remote adapter *1 *4 Camcorder etc. STEERING WHEEL REMOTE External monitor *5 Steering wheel remote controller (equipped in the car) USB devices B Connecting the iPod or the iPhone Connecting the external amplifiers and subwoofer USB 2.0 cable (accessory of the iPod/iPhone) You can connect an amplifier to upgrade your car stereo system. • Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit. • Disconnect the speakers from this unit, and connect them to the amplifier. Leave the speaker leads of this unit unused. • You can switch off the built-in amplifier and send the audio signals only to the external amplifier(s) to get clear sounds and to prevent internal heat built-up inside the unit. See page 42 of the INSTRUCTIONS. USB cable (approx. 1 m) KS-U30 USB device (not supplied) • To watch video, connect the iPod/iPhone using JVC KS-U30 *8 (separately purchased), otherwise, video is not displayed on the screen. • To listen to music, connect the iPod/iPhone using a USB 2.0 cable (accessory of the iPod/iPhone). *5 JVC Amplifier To the remote lead of other equipment Remote When connecting an iPod/iPhone for video playback (using KS-U30) and a Bluetooth adapter (KS-BTA100) at the same time *6 Y-connector *1 lead *1 • For details about connecting the Bluetooth adapter, see below. Subwoofer Remote lead (blue with white stripe) Rear speakers JVC Amplifier Front speakers KS-U30 JVC Amplifier *5 These plugs are not used *5 *6 D KS-BTA100 *6 Connecting an external navigation unit Connect an external navigation unit to the RGB input terminal. The positional information detected on the touch panel and picture signals from the navigation unit are transferred through the terminal. Refer to the manual of the external navigation unit for details. • Please contact your dealer to inquire about compatible navigation units. • JVC cannot guarantee proper operation of the external devices connected to the RGB input terminal. E External navigation unit *1 RGB input terminal Connecting the Bluetooth adapter KS-BTA100 *1 Blue with white stripe *1 Black Brown To the blue with white stripe lead of the supplied power cord 5 Ground To the brown lead of the supplied power cord 7 See page 48 of the INSTRUCTIONS. *1 Not supplied for this unit. *2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be turned on. Do not connect the lead directly to the battery. *3 Do not connect the lead to any device other than the OE remote adapter. Doing so may cause malfunction. *4 Alter the wire of the OE remote adapter to connect to the steering wheel remote lead. *5 Audio cord (not supplied for this unit). *6 Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint (if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit. *7 Video cord (not supplied for this unit). *8 When using the cable, you need to change the setting on the unit (see page 28 of the INSTRUCTIONS). • iPod and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. 2 EN_1-2_KWAVX50[A].indd 2 11.9.14 2:48:34 PM
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Fill forms, Extract, Assemble, Print high-res Create Date : 2011:09:14 14:50:35+09:00 Modify Date : 2011:09:27 13:06:32+09:00 Subject : LVT2289-002A Producer : Acrobat Distiller 7.0.5 for Macintosh Creation Date : 2011:09:14 14:50:35+09:00 Mod Date : 2011:09:27 13:06:32+09:00 Author : JVC Creator Tool : Adobe InDesign CS2 (4.0.5) Metadata Date : 2011:09:27 13:06:32+09:00 Document ID : uuid:7efd32a0-de95-11e0-804b-000a95943600 Instance ID : uuid:7efd3961-de95-11e0-804b-000a95943600 Format : application/pdf Creator : JVC Title : KW-AV50[A] Installation Manual Description : LVT2289-002A Page Count : 2 Page Mode : UseOutlines Page Layout : SinglePageEXIF Metadata provided by EXIF.tools