JVC KW AV51U AV61BT/KW AV51[U] User Manual AV51U, AV61BTU GET0888 002A
KW-AV61BTU KW-AV61BTU GET0888-002A English, Traditional Chinese, Thai, INSTALLATION MANUAL
KW-AV51U KW-AV51U INSTALLATION MANUAL (Asia) GET0888-002A
User Manual: JVC KW-AV51U KW-AV51U, KW-AV61BTU English, Traditional Chinese, Thai, INSTALLATION MANUAL
Open the PDF directly: View PDF 
.
Page Count: 6
- WARNINGS
- Parts list for installation and connection
- TROUBLESHOOTING
- INSTALLATION (IN-DASH MOUNTING)
- ELECTRICAL CONNECTIONS
- Connecting the parking brake lead
- Connecting the reverse gear signal lead (for rear view camera)
- Connecting to the steering wheel remote controller
- Connecting the external amplifiers and subwoofer
- Connecting the microphone (Only for KW-AV61BT)
- Connecting the Bluetooth adapter (Only for KW-AV51)
- Connecting an external navigation unit
- Connecting the external components
- USB devices
- Connecting the iPod or the iPhone
30˚
Only for KW-AV61BT
KW-AV61BT
KW-AV51
KW-AV61BT
KW-AV51
1
Parts list for installation and connection
KW-AV61BT/KW-AV51
Installation/Connection Manual
การติดตั้ง
การติดตั้ง/
ัตดิตรากอืมู่ค ้ง
ัตดิตรากอ
ื
มู่ค ้ง
ENGLISH
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your
vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC
car audio dealers.
WARNINGS
• DO NOT install any unit or wire any cable in a location where;
– it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic
accident.
– it may obstruct the operation of safety devices such as air bags, as this may result in a fatal
accident.
– it may obstruct visibility.
• DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic
accident.
• The driver must not watch the monitor while driving. It may lead to carelessness and cause an
accident.
• If you need to operate the unit while driving, be sure to look around carefully or you may be
involved in a traffic accident.
• If the parking brake is not engaged, “Parking Brake” appears on the monitor, and no playback
picture will be shown.
To prevent short circuits, disconnect the battery’s negative terminal and make all electrical
connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after installation.
• Be sure any cable is not caught on the car’s chassis or under seats.
Notes on electrical connections:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC
car audio dealer.
• It is recommended to connect speakers with maximum power of more than 50 W (both at the
rear and at the front, with an impedance of 4 to 8 Ω).
• To prevent short circuits, cover the terminals of the
UNUSED leads with insulating tape.
• At the time of installation, be sure to fix all wires (wires
both from this unit and from the car itself) in a way
that no wires can come into contact with heat sinks on
the rear and side of the unit.
CAUTION: Install this unit in the console of your vehicle. Do not touch the metal parts of this
unit during and shortly after the use of the unit. Metal parts such as the heat sink and enclosure
become hot.
Heat sink
GET0888-002A
[U]
1112EHHMDWJEIN
EN, CT, TH
© 2012 JVC KENWOOD Corporation
Round head
screws
(M5 x 8 mm)
Flat head screws
(M5 x 8 mm)
Main unit
Wiring harness
Monitor panel
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. However, you should make adjustments corresponding to
your specific car. If you have any questions or require information regarding installation kits, consult your JVC
car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Before installing the unit
• When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used, parts could
become loose or damaged.
• When tightening screws or bolts, be careful not to pinch any connection cord.
• Make sure not to block the fan on the rear to maintain proper ventilation when installing the unit.
1 Remove the audio system originally installed in the car, together with its mounting brackets.
• Be sure to keep all the screws and parts removed from your car for future use.
2 Attach the mounting brackets (removed from the car) to this unit (see below).
• Use flat head screws or round head screws, depending on installation location.
• When you need to use round head screws, use the supplied screws and the screws used to attach the metal
protection plates to the unit when shipped.
3 Do the required electrical connections.
• See “ELECTRICAL CONNECTIONS” on pages 1 and 2.
4 Install this unit using the screws removed in step 1.
5 Attach the monitor panel (see below).
Install the unit at an angle of
less than 30˚.
Connecting the parking brake lead
Parking brake
Parking brake switch
(inside the car)
Parking brake lead
(light green)
To metallic body or
chassis of the car
ELECTRICAL CONNECTIONS
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the wiring harness to the car battery;
otherwise, the unit will be seriously
damaged.
• BEFORE connecting the speaker leads of
the wiring harness to the speakers, check the
speaker wiring in your car.
TROUBLESHOOTING
Supplied
screws
Mounting bracket removed
from the car
Screws removed from the car in step 1
Supplied screws
Select the type of
screws appropriate
for the mounting
bracket.
Monitor panel
If necessary, restore the
protruding tabs.
When installing the unit in a Nissan car
If your Nissan car needs a plate, purchase the plate separately.
Plate for use with a
Nissan car (not supplied)
Step 5
• When you use screws other than those
supplied, use 8 mm-long screws. If
longer screws are used, they could
damage the unit.
• Tighten the screws firmly to prevent
the unit from falling off.
Locate the reverse lamp lead in the trunk. Extension wire (not supplied for this unit)
Purple with
white stripe
Reverse lamps
To reverse lamps
Reverse lamp lead
Connecting the reverse gear signal lead (for rear view camera)
• The fuse blows.
* Are the red and black leads connected
correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers
grounded in common?
• Noise interfere with sounds.
* Is the rear ground terminal connected to
the car’s chassis using shorter and thicker
cords?
• This unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers
grounded in common?
• This unit does not work at all.
* Have you reset your unit?
Remove the metal protection plates from the
unit before installation.
•
Keep the round head screws (M5 x 8 mm)
used to attach the metal protection plates. You
may need to use the screws for installation.
The following example is for installation in a Toyota car. For more details, consult your JVC car audio dealer.
Bag for storing the adapter MicrophoneBluetooth adapter
(attached)
Extension wire (supplied)
Extension wire
1-2_KW-AV61BT[U].indd 11-2_KW-AV61BT[U].indd 1 12.11.9 3:42:45 PM12.11.9 3:42:45 PM
*2
*2
1
2
3
4
5
6
7
8
31
*1
2
KW-AV61BT
KW-AV51
2
Connecting the Bluetooth adapter (Only for KW-AV51)
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
The leads of the wiring harness and those of the connector from the car body may be different in color.
1 Connect the colored leads of the wiring harness in the order specified in the illustration below.
2 Connect the antenna cord.
3 Finally connect the wiring harness to the unit.
See each diagram below.
Black
Yellow *3
Red
Orange with white stripe
Brown
Light green
Blue with white stripe
Blue
To the OE remote adapter *4
To metallic body or chassis of the car
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
To an accessory terminal in the fuse block
To car light control switch
Connecting the Bluetooth adapter (Only for KW-AV51)
To automatic antenna if any (250 mA max.)
To the remote lead of other equipment (200 mA max.)
White with black stripe White Gray with black stripe Gray Green with black stripe Green Purple with black stripe Purple
Left speaker
(front)
Right speaker
(front)
Left speaker
(rear)
Right speaker
(rear)
10 A fuse
Fan
Rear ground
terminal
Antenna
terminal
Connecting to the steering wheel remote controller
If your car is equipped with the steering wheel remote controller, you can operate this unit using the
controller. For connection, an exclusive remote adapter (not supplied) which matches your car is
required. For details, consult the same car audio dealer as where the unit is purchased.
A
OE remote adapter *2 *5
Steering wheel remote controller (equipped in the car)
*6
*6
*6
*7*7
*7
Connecting the external amplifiers and subwoofer
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it
can be controlled through this unit.
• Disconnect the speakers from this unit, and connect them to the amplifier. Leave the
speaker leads of this unit unused.
• You can switch off the built-in amplifier and send the audio signals only to the external amplifier(s) to
get clear sounds and to prevent internal heat built-up inside the unit.
See page 43 of the INSTRUCTION MANUAL.
B
Subwoofer
JVC
Amplifier
JVC Amplifier
JVC
Amplifier
Remote lead *2
Front
speakers
Rear
speakers
To the remote lead of other equipment
Remote lead (blue
with white stripe)
Y-connector *2
*8
*6
*8
Connecting the external components
F
Camcorder
etc. External
monitor
KV-CM10/KV-CM20 *2 *9
Rear view camera
USB devices
USB cable (approx. 1 m)
USB device
Connecting the iPod or the iPhone
KS-U30
(not supplied)
USB 2.0 cable (accessory of the
iPod/iPhone)
• To watch video, connect the iPod/iPhone using JVC KS-U30 *10 (separately purchased), otherwise,
video is not displayed on the screen.
• To listen to music, connect the iPod/iPhone using a USB 2.0 cable (accessory of the iPod/iPhone).
*1 Only for KW-AV61BT.
*2 Not supplied for this unit.
*3 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power
cannot be turned on. Do not connect the lead directly to the battery.
*4 Do not connect the lead to any device other than the OE remote adapter. Doing so may cause malfunction.
*5 Alter the wire of the OE remote adapter to connect to the steering wheel remote lead.
*6 Audio cord (not supplied for this unit).
*7 Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint
(if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.
*8 Video cord (not supplied for this unit).
*9 KV-CM10 / KV-CM20 is not sold in some areas. For details, consult your JVC car audio dealer.
*10 When using the cable, you need to change the setting on the unit (see page 25 of the INSTRUCTION
MANUAL).
Connecting an external navigation unit
E
Connect an external navigation unit to the RGB
input terminal. The positional information detected
on the touch panel and picture signals from the
navigation unit are transferred through the terminal.
Refer to the manual of the external navigation unit
for details.
• Please contact your dealer to inquire about compatible navigation units.
• JVC cannot guarantee proper operation of the external devices connected to the RGB input terminal.
External
navigation
unit *2
RGB input terminal
Fuse block
The terminals and cables of all models are shown in the
illustration for the purpose of explanation.
Ignition switch
(See page 1)
To parking brake (see page 1)
Connecting the microphone (Only for KW-AV61BT)
C
Secure the
microphone
cord using
cord clamps
(not supplied)
if necessary.
Microphone
123
D
To the brown lead of the
supplied wiring harness 7
To the blue with white
stripe lead of the supplied
wiring harness 5
Ground
*6
Blue with white stripe
Black
Brown
KS-BTA100
*2
See page 58 of the INSTRUCTION MANUAL.
Light blue with yellow stripe
KW-AV61BT
KW-AV51
KW-AV61BT
KW-AV51
KW-AV61BT
KW-AV51
KW-AV61BT/KW-AV51
KW-AV61BT/KW-AV51
Adhesive
tape
KW-AV61BT
KW-AV51
Not used
Extension wire (supplied)
1-2_KW-AV61BT[U].indd 21-2_KW-AV61BT[U].indd 2 12.11.9 3:42:47 PM12.11.9 3:42:47 PM
3
中文
本機僅可使用直流 12 V、負極接地的電源系統。如果您的車輛沒有這一電源系統，則需要
一個電壓變換器，可以在 JVC 汽車音響分銷商處買到。
警告
• 切勿在以下位置安裝本機或連接電纜；
– 可能會妨礙方向盤和變速排檔桿的操作，引發交通事故。
– 可能會妨礙操作安全裝置，如安全氣袋等，引發致命的交通事故。
– 可能會妨礙視野。
• 切勿在操作方向盤的過程中操作本機，否則可能引發交通事故。
• 駕駛時，駕駛員切勿緊盯顯示器。這可能會導致疏忽並引發事故。
• 在駕駛過程中若需要操作本機，切記要密切注意前方，否則可能引發交通事故。
• 若手煞車未嚙合，“Parking Brake（手煞車）”字樣在顯示器上出現，且無法播放圖
片。
為防止短路，在安裝本機之前，拔開電池的負極，並把所有電路都連接好。
• 安裝完畢後務必將本機的地線重新接至車身。
• 確定沒有任何電纜纏繞在汽車底盤上或座位下方。
進行電路連接時注意：
• 把保險絲更換為額定負荷值的保險絲。如果保險絲經常燒壞，請向 JVC 汽車音響分銷商
詢問。
• 後置和前置揚聲器的最大輸入功率應大於 50 W，
其阻抗為 4 Ω – 8 Ω。
• 為防止短路，請用絕緣帶包住未使用電線的端子。
• 安裝的時候請務必固定住所有電線（本機和汽車本
身的電線），使任何電線不會和本機後面板和側面
板上的散熱片接觸。
注意：將本機安裝在您汽車的控制台上。使用本機過程中和使用本機後不久，切勿觸摸
本機的金屬零件。金屬零件如散熱片和外殼會變熱。
散熱片
安裝（裝設、固定在儀表板內）
下面的圖解表示了典型的安裝程序。但是在實際安裝時，您應該根據您的汽車作適當的調整。如果您有
問題，或需要有關配套元件的資料，請向 JVC 汽車音響分銷商或配套元件供應公司詢問。
• 如果您不能確定如何正確地安裝本機，應請合格的技術人員來安裝。
安裝本機之前
• 當裝上本機時，必須按照指示使用配備的螺絲釘。如果使用其它的螺絲釘，相關零件可能會鬆脫或損
壞。
• 當鎖緊螺絲釘或螺栓時，切記不要壓擠到任何連接電線。
• 當安裝上後，切記不要阻擋到後面板的風扇以維持適當的通風。
1 拆卸原本安裝在汽車內的音響系統，以及其裝配架。
• 請務必保留所有從您汽車拆卸的螺絲和零件做日後使用。
2 將（從汽車拆卸的）裝配架安上本機（參閱下列內容）。
• 根據安裝位置使用平頭螺絲或圓頭螺絲。
• 當您需要使用圓頭螺絲時，請使用配備的螺絲和出廠時就已用來將金屬保護框安裝至本機的螺絲。
3 執行必要的電路連接。
• 參閱第 3 和 4 頁的“電路連接”。
4 使用在步驟 1 拆卸的螺絲安裝本機。
5 安裝顯示器面板（參閱下列內容）。
連接至手煞車導線
手煞車
手煞車開關（位於車內）
手煞車導線
（淺綠色）
接至金屬體或
汽車底盤
電路連接
30˚
將本機安裝在少於 30˚ 的角
度。
配備螺絲
從汽車拆卸的裝配架
在步驟 1 從汽車拆卸的螺絲
配備螺絲
選擇適合裝配架
的螺絲型號。
顯示器面板
若有必要，請重新裝上
凸緣。
當安裝本機於日產（Nissan）汽車時
若有需要，請另購用於日產（Nissan）汽車的框。
用於日產（Nissan）汽
車的框（另購）
步驟 5
• 當您使用的不是配備的螺絲時，請
使用 8 mm 長的螺絲。若使用比較
長的螺絲，有關螺絲可能會損壞本
機。
• 擰緊螺絲以防本機摔落。
連接反向變速器信號導線（對應後視攝影機）
以下以豐田（Toyota）汽車安裝為例。請聯絡您的 JVC 汽車音響分銷商有關更多細節。
延長線（附帶）
電源和揚聲器接線注意事項：
• 切勿將配線束的揚聲器導線接頭接至汽車電池；否則，本機將會嚴重損壞。
• 在將配線束的揚聲器導線接頭接至揚聲器
之前，檢查您汽車上的揚聲器線路。
故障排除
• 保險絲燒斷。
* 檢查紅色導線接頭和黑色導線接頭是否
正確接上？
• 電源不能接通。
* 檢查黃色導線接頭是否接上？
• 揚聲器沒有聲訊。
* 檢查揚聲器輸出導線接頭是否短路？
• 聲訊失真。
* 檢查揚聲器輸出導線接頭是否接地？
* 檢查揚聲器的左（L），右（R）端子的
負極“–”是否共同接地？
• 噪音干擾音響。
* 後接地端子與車身是否使用較短和較厚
的電線連接？
• 本機發熱。
* 檢查揚聲器輸出導線接頭是否接地？
* 檢查揚聲器的左（L），右（R）端子的
負極“–”是否共同接地？
• 本機完全不能正確操作。
* 您有沒有重置本機？
僅對應 KW-AV61BT
用於安裝和連接的零件清單
圓頭螺絲
（M5 x 8 mm）
平頭螺絲
（M5 x 8 mm）
主機 顯示器面板
安裝前請從本機上卸下金屬保護框。
• 請妥善保管用於安裝金屬保護框的
圓頭螺絲（M5 x 8 mm）。您可能需
要使用這些螺絲來進行安裝。
存放轉換器的包 麥克風藍牙轉換器
（已插入）
KW-AV61BT
KW-AV51
延長線 配線束
找出後車箱的倒車信號燈導線。 延長線（不隨本機提供）
紫色帶有
白色條紋
倒車信號燈
接至倒車信號燈
倒車信號燈導線
KW-AV61BT
KW-AV51
3-4_KWAV61BT[U].indd 33-4_KWAV61BT[U].indd 3 2012-10-30 13:33:132012-10-30 13:33:13
KW-AV61BT
KW-AV51
*2
*2
1
2
3
4
5
6
7
8
31
*1
2
4
接線前：仔細檢查汽車內的線路。不正確的接線會導致本機嚴重損壞。
配線束的導線和車身的連接器的導線在顏色上可能有所不同。
1 依照下圖所示之次序連接配線束的顏色導線。
2 將天線的電線連接起來。
3 最後，把配線束的插頭插在本機上。
參閱以下的每個圖表。
黑色
黃色 *3
紅色
橙色帶有白色條紋
褐色
藍色帶有白色條紋
藍色
接至 OE 遙控轉換器 *4
接至金屬體或汽車底盤
接至保險絲單元內的帶電端子，保險絲單元與車裝電池
相連接（用於旁路點火開關）（恆定 12 V）
接至保險絲單元內的附屬端子
接至汽車車燈控制開關
連接藍牙轉換器（僅對應 KW-AV51）
接至自動天線（若有裝設）（最大 250 mA）
接至其他裝置上的遙控導線（最大 200 mA）
延長線（附帶）
白色帶有黑色條紋 白色 灰色帶有黑色條紋 灰色 綠色帶有黑色條紋 綠色 紫色帶有黑色條紋 紫色
左揚聲器
（前置）
右揚聲器
（前置）
左揚聲器
（後置）
右揚聲器
（後置）
10 A 保險絲
風扇
本機後背接地端子
天線端子
連接至方向盤遙控器
若汽車配備了方向盤遙控器，可以用遙控器操作本機。對應連接，需要和汽車配套的專用遙控
轉換器（另購）。關於詳情，請與銷售本機的汽車音響分銷商聯系。
A
OE 遙控轉換器 *2 *5
方向盤遙控器（汽車上配備）
*6
*6
*6
*7*7
*7
連接外接功率放大器和重低音揚聲器
您可以連接功率放大器以提昇尊車的音響系統。
• 將遙控導線（藍色帶有白色條紋）和其他裝置上的遙控導線連接起來，以便可以從本機進行
遙控。
• 將揚聲器和本機拔開，再接上功率放大器。將本機的揚聲器接線放置不用。
• 您可以關閉內建功率放大器，將聲音信號僅傳送到外接功率放大器，從而得到清晰的音質，
並防止本機內部積聚熱量。
參閱使用說明書的第 43 頁。
B
重低音揚聲器
JVC 功率
放大器
JVC 功率
放大器
JVC 功率
放大器
遙控導線
*2
後置
揚聲器
前置
揚聲器
接至其他裝置上的遙控導線
遙控導線（藍色
帶有白色條紋）
Y-型連接導線
*2
*8
*6
*8
連接外接裝置
F
攝錄相機等 外接
顯示器
KV-CM10 / KV-CM20 *2 *9
後視攝影機
USB 裝置
USB 電纜（大約 1 m）
USB 裝置
連接 iPod 或 iPhone
KS-U30
（另購）
USB 2.0 電纜（iPod/iPhone 的附件）
• 想要觀看視訊，使用 JVC KS-U30 *10（另購）連接 iPod/iPhone，否則，視訊不會在螢幕上顯
示。
• 想要聆聽音樂，使用 USB 2.0 電纜（iPod/iPhone 的附件）連接 iPod/iPhone。
*1 僅對應 KW-AV61BT。
*2 不隨本機提供。
*3 本機未安裝時，進行工作狀況檢查之前，必須把這導線接上，否則不能開啟電源。切勿將導線直接連接
至電池。
*4 切勿將導線連接至除 OE 遙控轉換器以外的任何裝置。這可能會引起故障。
*5 更改 OE 遙控轉換器的接線，將其連接至方向盤遙控導線。
*6 聲音導線（不隨本機提供）。
*7 將地線與金屬車體或者汽車底盤緊密連接，連接處應該沒有被油漆覆蓋（如果已塗上油漆，在連接電線
前，將油漆刮去）。如果不這樣做，可能會損壞本機。
*8 影像線（不隨本機提供）。
*9 KV-CM10 / KV-CM20 在某些地區不銷售。關於詳情，請與 JVC 汽車音響分銷商聯系。
*10 使用電纜時，您需要在本機上切換設定（參閱使用說明書的第 25 頁）。
連接外接導航裝置
E
將外接導航裝置連接至 RGB 輸入端子。
觸摸屏上檢測到的方位訊息和導航裝置中的圖像
信號從該端子進行傳輸。
關於詳情，參閱外接導航裝置的使用手冊。
• 請洽詢分銷商關於相容導航裝置的訊息。
• JVC 不保證接上 RGB 輸入端子的外接裝置是否
能正常操作。
外接導航
裝置 *2
RGB 輸入端子
保險絲單元
所有型號的端子和電纜在圖中顯示，用作解釋說明。
點火開關
（參閱第 3 頁）
接至手煞車（參閱第 3 頁）
連接麥克風（僅對應 KW-AV61BT）
C
如需要，使用固定
線箍（另購）固定
麥克風導線。
麥克風
123
D連接藍牙轉換器（僅對應 KW-AV51）
接至附帶配線束的褐色
導線 7
接至附帶配線束的藍色帶
有白色條紋的導線 5
接地
藍色帶有白色條紋
黑色
褐色
KS-BTA100
*2
參閱使用說明書的第 58 頁。
膠帶
不用
淺藍色帶有黃色條紋
KW-AV61BT
KW-AV51
KW-AV61BT/KW-AV51
KW-AV51
KW-AV61BT
KW-AV61BT
KW-AV51
KW-AV61BT
KW-AV51 KW-AV61BT/KW-AV51
*6
淺綠色
3-4_KWAV61BT[U].indd 43-4_KWAV61BT[U].indd 4 2012-10-30 13:33:172012-10-30 13:33:17
5
( )
12
JVC
•
–
–
–
•
•
•
•
“Parking Brake( )”
•
•
:
• JVC
•
50 ( 4
8 Ω)
•
•
( )
:
( )
30˚
30˚
( )
5
•
8
•
( )
()
JVC
:
•
•
•
* ?
•
* ?
•
* ?
•
* ?
* “–” L () R ()
?
•
*
?
•
* ?
* “–” L () R ()
?
•
* ?
KW-AV61BT
KW-AV61BT
KW-AV51
(M5 x 8 )
(M5 x 8 )
• (M5 x 8 )
Bluetooth
( )
( )
JVC
•
•
•
•
1
•
2 ( ) ( )
•
•
3
• “ ” 5 6
4 1
5 ( )
1
()
KW-AV61BT
KW-AV51
5-6_KW-AV61BT[U].indd 55-6_KW-AV61BT[U].indd 5 11/7/12 9:42:10 AM11/7/12 9:42:10 AM
KW-AV61BT
KW-AV51
6
*2
*2
1
2
3
4
5
6
7
8
31
*1
2
:
1
2
3
*3
OE *4
() ( 12 V)
(
250 mA)
(
200 mA)
( )
()
()
()
()
10 A
( )
A
OE *2 *5
()
*6
*6
*6
*7*7
*7
• ()
•
•
43
B
JVC
JVC
JVC
*2
()
Y *2
*8
*6
*8
F
KV-CM10 / KV-CM20 *2 *9
USB
USB ( 1 )
USB
iPod iPhone
KS-U30
( )
USB 2.0 ( iPod/iPhone)
*1 KW-AV61BT
*2
*3
*4 OE
*5 OE
*6 ( )
*7 (
)
*8 ( )
*9 KV-CM10 / KV-CM20
JVC
*10 ( 25 )
E
RGB
•
• JVC RGB
*2
RGB
( 1)
( 1)
( KW-AV61BT )
C
( )
123
D Bluetooth ( KW-AV51 )
7
5
KS-BTA100
*2
58
KW-AV61BT
KW-AV51
KW-AV61BT/KW-AV51
KW-AV51
KW-AV61BT
KW-AV61BT
KW-AV51
KW-AV61BT
KW-AV51
KW-AV61BT/KW-AV51
*6
• iPod/iPhone JVC KS-U30 *10 ()
• iPod/iPhone USB 2.0 ( iPod/iPhone)
Bluetooth ( KW-AV51 )
5-6_KW-AV61BT[U].indd 65-6_KW-AV61BT[U].indd 6 11/12/12 3:35:05 PM11/12/12 3:35:05 PM
