JVC LT 19DA1BJ 19DA9BJ User Manual 1EMN24540 EN
User Manual: JVC LT-19DA1BJ LT-19DA1BJ English,
Open the PDF directly: View PDF 
.
Page Count: 24
| Download | |
| Open PDF In Browser | View PDF |
LT-19DA1BJ WIDE LCD PANEL TV INSTRUCTIONS PRECAUTIONS The LCD panel is a very high technology product with 921,600 thin film transistors, giving you fine picture details. Occasionally, a few non-active pixels may appear on the TV screen as a fixed point of blue, green or red. Please note that this does not affect the performance of your product. 9) Disconnect the mains plug to switch off when the unit becomes faulty or not in use. 10) The mains plug shall remain readily operable. 11) Read the manual instructions to ensure correct and safe installation and interconnection of the unit in multimedia systems. 12) Keep a distance of 20 cm around the ventilation openings of the apparatus. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. CAUTION - RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Connection to Power Before Switching on make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. Mains Cord This appliance may be fitted with a non-rewireable plug. If it is necessary to change the fuse in a nonrewireable plug the fuse cover must be refitted. If the fuse cover is lost or damaged, the plug must not be used until a replacement available from the appliance manufacturer is obtained. It is important that the colour of the replacement fuse cover corresponds with the rating marking on the base of the plug. If the plug has to be changed because it is not suitable for your socket, or becomes damaged, it should be cut off and an appropriate plug fitted following the wiring instructions below. The plug removed must be disposed of safely as insertion into a 13A socket is likely to cause an electrical hazard. For your own safety read the following instructions carefully before attempting to connect this unit to mains. The wires in this mains lead are coloured in accordance with the following code: BLUE=NEUTRAL, BROWN=LIVE Important As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. No connection is to be made to the earth terminal of the plug. If a 13 Amp (BS 1363) Plug is used, a 5 Amp Fuse must be fitted, or if any other type of Plug is used a 3 or 5 Amp Fuse must be fitted, either in the Plug or Adaptor, or on the Distribution Board. Mains Supply: 220 - 240 V~ 50 Hz - AC only Do not make any connection to the larger pin marked with the letter “E” or by the symbol Uor coloured green or green and yellow. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the apparatus’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the apparatus. POWER SUPPLY The main power supply is engaged when the main plug is plugged in a 220-240 V~, 50 Hz AC outlet. To operate the unit, press [ (standby-on)] to turn on the unit. WARNING: LIVE PARTS INSIDE. DO NOT REMOVE ANY SCREWS. CAUTION 1) Do not attempt to open the cabinet. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. 2) Slots and openings in the cabinet and the sides or bottom are provided for ventilation. To ensure reliable operation and to protect the unit from overheating, these openings must not be blocked or covered. Avoid installation in enclosed spaces such as bookcases unless proper ventilation is provided. 3) Keep the unit away from radiators and other heat sources. 4) Do not push objects of any kind into the unit through the cabinet slots or openings as they could touch electrically live parts or short circuit parts resulting in a fire or electric shock. 5) To prevent fire or shock hazard, do not expose this apparatus to dripping or splashing, no objects filled with liquids, such as vases, should be placed on the apparatus. 6) Use the unit on a horizontal (flat) surface only. 7) Do not place any combustible objects on the device (candles, etc.). 8) The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks. EN FUSE BROWN (Live) BLUE (Neutral) CORD GRIP OUTER SHEATH OF THE WIRE Do not place the unit on the furniture that is capable of being tilted by a child or an adult leaning, pulling, standing or climbing on it. A falling unit can cause serious injury or even death. 2 TABLE OF CONTENTS PRECAUTIONS .................................................................................................................................................2 THINGS TO DO FOR THE FIRST TIME ...........................................................................................................4 OPERATING CONTROLS AND FUNCTIONS ..................................................................................................5 PREPARATION FOR USE ................................................................................................................................7 SETUP FOR USE ..............................................................................................................................................9 OPERATIONS .................................................................................................................................................12 OTHER SETTINGS .........................................................................................................................................18 MAINTENANCE...............................................................................................................................................21 TROUBLESHOOTING GUIDE ........................................................................................................................21 SPECIFICATIONS ...........................................................................................................................................22 Features A Note about Recycling • • • • • • • • This unit’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations. This product consists of materials which can be recycled and reused if disassembled by a specialised company. • • • • Integrated Digital Terrestrial Tuner (DVB) EPG (Electronic Programme Guide) Stereo Sound System On-Screen Display Sleep Timer Teletext TV Screen Mode Selection Auto Power Off Function - If there is no signal input from the antenna terminal and no user operation for 15 minutes, the unit will be turned off automatically. HDMI Input COMPONENT Input S-VIDEO Input PC Input Information for Users on Disposal of Old Equipment and Batteries [European Union] These symbols indicate that the electrical and electronic equipment and the battery with this symbol should not be disposed of as general household waste at its end-of-life. Instead, the products should be handed over to the applicable collection points for the recycling of electrical and electronic equipment as well as batteries for proper treatment, recovery and recycling in accordance with your national Products legislation and the Directive 2002/96/EC and 2006/66/EC. By disposing of these products correctly, you will help to conserve natural resources and will help to prevent potential negative effects on the environment and human health which could otherwise be caused by inappropriate waste handling of these products. For more information about collection points and recycling of these products, please contact Battery your local municipal office, your household waste disposal service or the shop where you purchased the product. Notice: Penalties may be applicable for incorrect The sign Pb below disposal of this waste, in accordance with the symbol for national legislation. batteries indicates that this battery [Business users] contains lead. If you wish to dispose of this product, please visit our web page www.jvc-europe.com to obtain information about the take-back of the product. [Other Countries outside the European Union] These symbols are only valid in the European Union. If you wish to dispose of these items, please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment and batteries. Supplied Accessories • Remote control • Two R6 (AA) batteries • INSTRUCTIONS Trademark Information • HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. • DVB is a registered trademark of the DVB Project Symbols Used in this Manual The followings are the description for the symbols used in this manual. DTV Digital TV operation ATV Analogue TV operation Model/Serial Number To aid reporting in case of loss or theft, please record the unit’s model and serial numbers in the space provided. The numbers are located at the rear of the unit. Model number: _________________ Serial number: _________________ Dear Customer, This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety. European representative of Victor Company of Japan, Limited is: JVC Technical Services Europe GmbH Postfach 10 05 04 61145 Friedberg Germany 3 EN THINGS TO DO FOR THE FIRST TIME Attaching the stand You need to attach the stand to the unit to display upright. Make sure the front and rear of the stand match the proper direction. 1) Place the unit face down onto the soft stuff such as a cloth on a table. Be careful not to damage the TV screen. 2) Insert the stand all the way to the unit slowly. Be careful not to put the AC cord between the stand and the unit. 3) Make sure the stand clicks. To remove the stand from the unit Pull the stand toward the direction B pressing the hooks A at once and remove the stand from the unit slowly. Be careful not to drop the stand when you remove it. A B A Note: • Make sure to use the table which can support the weight and size of the unit. • Make sure the table is in a stable location. Handling the glossy finish of the unit Be careful when handling the glossy finish of the unit. The glossy finish of the unit scratches easily. • Protection films have been pasted onto the glossy finish of the unit to prevent scratches. Peel off the films after the unit has been placed properly. • If the glossy finish gets dirty, clear the dust off the glossy finish first. Then wipe softly with soft cloth. If you do not clear the dust first, or you wipe the glossy finish too hard, the glossy finish may be scratched. EN Glossy finish 4 OPERATING CONTROLS AND FUNCTIONS All operations described are based on the use of the remote control. Some operations can be carried out using the buttons on the control panel. CONTROL PANEL REMOTE CONTROL 7 1 8 1 2 9 3 3 17 19 18 5 23 25 14 27 16 10 11 12 4 5 6 1. 13 15 29 Press to determine the setting on the menu. Press to select or adjust from a particular menu. Press to display the channel list while watching a programme. INPUT SELECT/OK(control panel) / AV (remote control) Press to switch TV or external input mode. 15. GUIDE INPUT SELECT/OK(control panel) Press to display EPG (Electronic Programme Guide) in digital mode. Press to determine the setting on the menu. 3. PROG. / 16. BACK (control panel) Press to return to the previous display. Press to select the setting on the menu. Press to select the item you want to adjust in the picture control mode. Press to go to the next page or the previous page of teletext. Same function as Cursor K / L (remote control) on the menu. PROG. control) / (control panel) / P /P 17. VOL. / control) (control panel) / +/ 18. (prog.) (remote (control panel) VOL. (control panel) – (vol.) (remote 19. MENU (VCR, DVD: forward) Press to switch TV or RADIO mode. Press to begin playback.(VCR / DVD) STAND BY/POWER indicator 22. ZOOM / (VCR, DVD: pause) Press to switch the aspect ratio available for the TV screen. Press to pause playback. (VCR / DVD) (mute) 23. Press to mute the sound. Press this button again or press VOL. / on the control panel +/ – (vol.) on the remote control to restore sound. or (sleep) / (VCR: recording) Press to set the sleep timer. Press to start recording with pressing TV/RADIO / B at the same time. (VCR) / at the same Press to pause recording with pressing time. (VCR) Press to call up the title menu on a DVD. (DVD) TV / VCR / DVD switch Switch to control basic operations of VCR / DVD using this remote control on our JVC brand. 9. (VCR: rewind, DVD: reverse) 21. TV/RADIO / B (VCR, DVD: play) Lights up in green when power is on. Lights up in red when power is in standby mode. 8. (audio language) / Press to select the colour input signal from external devices. Press to fast forward the tape. (VCR) Press to search forward through the disc. (DVD) Press to display the menu. Press to call up the VCR menu. (VCR) Press to call up the menu on a DVD. (DVD) 7. (VCR: programme –, DVD: skip backward) 20. COLOUR SYSTEM / Same function as Cursor s (remote control) on the menu. 6. (text) / Press to change the audio language. Press to rewind the tape. (VCR) Press to search backward through the disc. (DVD) Same function as Cursor B (remote control) on the menu. 5. (VCR: programme +, DVD: skip forward) Press to display the teletext information. Press to change TV channels. (VCR) Press to skip chapters or tracks. (DVD) Press to control the volume level. VOL. (sound) / Press to change the sound modes. Press to change TV channels. (VCR) Press to skip chapters or tracks. (DVD) Press to select memorised channel or other modes. 4. 20 21 22 24 26 28 14. OK (standby-on) Press to turn on or off (standby) the unit. 2. 2 4 Number buttons Press two digits to directly access the desired channel in analogue mode. Press three digits to directly access the desired channel in digital mode. Press to enter the password in the password input field. 24. (subtitle) / (VCR, DVD: stop) Press to change the available subtitle languages. Press to stop playback or recording. (VCR) Press to stop playback. (DVD) 25. 10. I (information) (index) Press to go back to the start page of teletext. Press to display the TV screen information. 26. 11. RED/GREEN/YELLOW/BLUE (sub page) Press to select subpages of teletext. Press to directly select the page numbers of teletext or digital teletext. 27. Press to select digital or analogue mode. 28. Press to select the setting on the menu. Press to select item you want to adjust in the picture control mode. Press to go to the next page or the previous page of teletext. 29. Infrared sensor window (reveal) Press to call up the hidden information of teletext. 12. TV/DTV (expand) Press to enlarge fonts of teletext. 13. Cursor K / L / s / B buttons Receives the infrared rays transmitted from the remote control. 5 EN Installing the Batteries 1) Open the battery compartment cover. 2) Insert “R6” penlight batteries into battery compartment in the direction as indicated by the polarity (+/–) markings. Batteries installed with incorrect polarity may damage the remote unit. 3) Close the cover. 4) Push the cover on its top side until it clicks in order to fit the cover completely to the compartment. Note: Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. REAR PANEL 32 COMPONENT AUDIO 30 Y Pb Pr L R PC-IN RGB C. I. HDMI IN HDMI COMPONENT 31 AUDIO Y Pb Pr L R 40 33 36 34 38 37 35 VIDEO HEAD PHONE AUDIO VIDEO L R S-VIDEO PC-IN SCART 39 VIDEO HEAD PHONE AUDIO VIDEO L R S-VIDEO PC-IN SCART 30. PC-IN (RGB) input jack 36. AUDIO (L/R) input jack Connect a VGA cable (commercially available) to the monitor jack of a PC. Connect an RCA audio cable (commercially available) to the audio output jack of an external device. Note: The AUDIO (L) jack is for monaural input. The 31. HDMI-IN input jack sound is heard from both speakers. Use this jack for a monaural audio device. Connect an HDMI cable (commercially available) to the HDMI output jack of an external device. 32. COMPONENT (Y/Pb/Pr) / AUDIO (L/R) input jack 37. S-VIDEO input jack Connect an RCA component video and an RCA audio cable (commercially available) to the component video and audio output jack of an external device. Connect an S-video cable (commercially available) to the S-video output jack of an external device. 38. PC-IN (Audio) input jack 33. Connect a mini-plug audio cable (commercially available) to the audio line out jack of a PC. (Aerial) input jack Connect an RF coaxial cable (commercially available) to an antenna or RF output jack of a cable system. 39. SCART jack Connect a scart cable (commercially available) to the scart jack of an external device. 34. HEAD PHONE jack Connect a headphone. 40. C.I. (COMMON INTERFACE) slot 35. VIDEO input jack Common Interface (CI) Module: Insert the CI module. Connect an RCA video cable (commercially available) to the video output jack of an external device. EN 6 PREPARATION FOR USE Antenna Connection External Connection UHF VHF [HDMI CONNECTION] HDMI connection offers the highest picture quality. HDMI (High Definition Multimedia Interface) transports high definition video and multi-channel digital audio through a single cable. Connect the HDMI output jack of your video device and the HDMI-IN jack of the unit. Use an HDMI cable (commercially available). Rear of this unit VHF/UHF MIXER RF cable (not supplied) Rear of this unit To (Aerial) input jack 1) Connect an RF cable (commercially available) to input jack at the rear of this unit. HDMI cable (not supplied) (Aerial) HDMI OUT 2) Plug this unit into an AC outlet. 3) The STAND BY/POWER indicator on the front panel lights red, then press [ (standby-on)] to turn on the unit. Dear Customer, By connecting an HDMI cable to your JVC LCD TV, you have to use only a certified HDMI cable to guarantee a sufficient immunity against parasitic frequency radiation. A certified HDMI cable can be identified by the HDMI logo on the cable or the cable package. Note: • This unit accepts 480i / 480p / 576i / 576p / 720p / 1080i video signals and 32 kHz / 44.1 kHz / 48 kHz audio signals. • This unit accepts only 2 channel audio signals (LPCM). • You need to select “PCM” for the digital audio output of the device you connect. Make sure the device outputs the digital audio. Audio sometimes makes no sound if you select “Bitstream”, etc. [SCART CONNECTION] Scart connection offers better picture quality. Connect the scart jack of your video device and the SCART jack of this unit. Use a scart cable (commercially available). Rear of this unit VIDEO AD ONE AUDIO VIDEO L R S-VIDEO P SCART scart cable (not supplied) 7 EN [COMPONENT CONNECTION] [VIDEO CONNECTION] RCA component video connection offers better picture quality. 1) Connect the component video output jack (Y, Pb, Pr) of your video device and the COMPONENT video(Y, Pb, Pr) input jack of this unit. Use an RCA component video cable (commercially available). RCA video connection offers standard picture quality. 1) Connect the video output jack of your video device and the VIDEO input jack of this unit. Use an RCA video cable (commercially available). 2) Connect the audio output jack of your video device and the AUDIO (L/R) input jack of this unit. Use an RCA audio cable (commercially available). 2) Connect the audio output jack of your device and the AUDIO (L/R) input jack of this unit. Use an RCA audio cable (commercially available). RCA audio cable (not supplied) RCA component video cable (not supplied) Rear of this unit AUDIO OUT VIDEO OUT COMPONENT AUDIO Y Pb Pr L R VIDEO AD ONE Rear of this unit AUDIO VIDEO L R S-VIDEO P SCART RCA video cable (not supplied) RCA audio cable (not supplied) [PC CONNECTION] Note: This unit accepts 480i / 480p / 576i / 576p / 720p / If you connect this unit and your PC, you can use this unit as a computer monitor. 1) Connect the monitor jack of your PC and the PC-IN (RGB) jack of this unit. Use a VGA cable with ferrite core (commercially available). 1080i video signals. [S-VIDEO CONNECTION] S-video connection offers good picture quality. 1) Connect the S-video output jack of your video device and the S-VIDEO input jack of this unit. Use an S-video cable (commercially available). 2) Connect the audio line out jack of your PC and the PC-IN (Audio) jack of this unit. Use a mini-plug audio cable (commercially available). 2) Connect the audio output jack of your device and the AUDIO (L/R) input jack of this unit. Use an RCA audio cable (commercially available). Rear of this unit VGA cable with ferrite core (not supplied) RCA audio cable (not supplied) To PC-IN jack Rear of this unit AUDIO OUT VIDEO S-VIDEO OUT OUT To monitor jack mini-plug audio cable (not supplied) VIDEO HEAD PHONE AUDIO VIDEO L R S-VIDEO PC-IN SCART S-VIDEO PC-IN To audio line out jack S-video cable (not supplied) Precautions for the connection to other devices: Note: If you connect to the S-VIDEO jack and the VIDEO Please use the VGA cable that has a ferrite core. jack at the same time, S-video connection will have priority. EN 8 SETUP FOR USE Initial Setting DTV Auto Scan ATV DTV You need to set the followings to use the unit appropriately for the first time you turn on the unit. You can scan the digital channels receivable in your area automatically. 1) Press [ (standby-on)] to turn on the unit. • “Initial Setup” language menu will appear. 1) Press [MENU] to display the menu in digital mode. 2) Press [K / L] repeatedly to select the menu language you want, then press [OK]. 3) Press [K / L] to select “Auto Scan”, then press [OK]. • Scanning will start automatically. 2) Press [K / L] to select “CHANNEL”, then press [OK]. Initial Setup EXIT Select the language for setup display. 32% þHã SOUND 1HGHUODQGV English CHANNEL )UDQoDLV Select OK Auto Scan Now the system is scanning for channels, please wait. PICTURE Ȼɴɥɝɚɪɫɤɢ MENU 'HXWVFK DETAIL Exit LANGUAGE DTV Services 0 Radio Services 0 No Items No Items BACK Back • When the scanning is completed, the lowest memorised digital channel will be displayed. • If you press [MENU] during the scanning, this operation will be stopped and the lowest memorised digital channel will be displayed. • “Initial Setup” antenna confirmation menu will appear. 3) Press [K / L] to select “Yes”, then press [OK]. • Channel scanning will start automatically. Initial Setup ATV Now the system is scanning for channels, please wait. You can scan the analogue channels receivable in your area automatically. 26% DTV Services No Items 0 Radio Services 0 No Items 1) Press [MENU] to display the menu in analogue mode. MENU 2) Press [K / L] to select “CHANNEL”, then press [OK]. Exit 3) Press [K / L] to select “Auto Scan”, then press [OK]. • Scanning will start automatically. • When the scanning is completed, the lowest memorised digital channel will be displayed. EXIT Note: • If you select “No” in antenna confirmation menu, the Auto Scan Now the system is scanning for channels, please wait. operation will be cancelled. • If you press [MENU] during auto scanning, the operation will be cancelled. • If there is no signal input from the antenna terminal and no operation for several seconds, the next display will appear. Follow the instructions on the TV screen. PICTURE SOUND VHF-L 25% CHANNEL Analog channels 0 ch DETAIL LANGUAGE No channel is registered. Press and hold "OK" key on the remote control for 3 seconds. Set proceeds to initial channel search. BACK Back • When the scanning is completed, the lowest memorised analogue channel will be displayed. • If you press [MENU] during the scanning, this operation will be stopped and the lowest memorised analogue channel will be displayed. • Please note that after tuning, the analogue channels will be stored in the order that they are broadcast by your local transmitter. This may not be in the same order in which you would like them to be stored. If this is the case, you can change the order according to your preference. To do this, see "To change the channel order manually" on Page 16. 9 EN Manual Scan 10) Press [K / L] to select “Sound System”, then press [OK]. 11) Press [K / L] to select the system you want, then press [OK]. DTV You can adjust a digital channel individually. e.g.) “Color System” is “Pal” 1) Press [MENU] to display the menu in digital mode. EXIT 2) Press [K / L] to select “CHANNEL”, then press [OK]. PICTURE 3) Press [K / L] to select “Manual Scan”, then press [OK]. Channel Frequency SOUND 4) Press [s / B] to select the channel number you want to scan. • The tuner will start searching up or down automatically. When a channel is found, the searching will stop. EXIT Manual Adjust Scan Color System L B/G L' CHANNEL Sound System DETAIL D/K B/G lD/K LANGUAGE Manual Scan PICTURE Channel Number SOUND Signal Strength 69 12) Press [MENU] to exit. P CHANNEL Now 100 Peak 100 DETAIL 10 key LANGUAGE P Ch change OK BACK Back 5) Press [MENU] to exit. Language Selection ATV DTV ATV You can adjust an analogue channel individually. You can select the main language. 1) Press [MENU] to display the menu in analogue mode. 1) Press [MENU] to display the menu. 2) Press [K / L] to select “CHANNEL”, then press [OK]. 2) Press [K / L] to select “LANGUAGE”, then press [OK]. 3) Press [K / L] to select “Manual Scan”, then press [OK]. 3) Press [K / L] to select your desired item, then press [OK]. 4) Press [s / B] to select the channel number you want to scan. 4) Press [K / L] repeatedly to select the language you want, then press [OK]. 5) Press [K / L] to select “Frequency”. 6) Press [the Number buttons] to enter the frequency. • To select 24, enter [0] first, then press [2] and [4]. EXIT PICTURE 7) Press [s / B] to start searching. • The tuner will start searching up or down automatically. When a channel is found the searching will stop. EXIT Manual Scan PICTURE Channel SOUND CHANNEL SOUND 1 5) Press [MENU] to exit. 222 MHz Color System Pal Sound System B/G Note: • “Audio Language” and “Subtitle Language” are available only for digital mode. • While watching a programme, you can change the audio language easily using [ (audio language) / ] when it is available. • While watching a programme, you can change the subtitle language easily using [ (subtitle) / ] when it is available. 21% Manual Scan Channel Frequency Color System CHANNEL Pal SECAM Sound System DETAIL LANGUAGE EN French LANGUAGE Frequency SOUND French DETAIL 9) Press [K / L] to select the system (“Pal, SECAM”) you want, then press [OK]. PICTURE Subtitle Language English CHANNEL 8) Press [K / L] to select “Color System”, then press [OK]. EXIT Menu Language Audio Language DETAIL LANGUAGE Setup 10 Teletext C.I. (Common Interface) ATV DTV You can retrieve the teletext information along with analogue TV channels. This unit is equipped with a C.I. (Common Interface) slot. You can enjoy additional services with this function, for example Pay TV. The access restrictions menu will appear on the TV screen when a CI module is installed. 1) Press [ (text) / ] to turn on the teletext decoder. • Teletext information will appear. • If you want to select other pages, press [the Number buttons] or [K / L]. 2) Press [ (text) / transparent mode. 1) Turn off the unit and unplug from an AC outlet. 2) Insert the CI module straight to the C.I. slot of this unit. • Some CI modules may be a two-piece design consisting of a card reader with the viewing card. When using this kind of card, insert the card reader firmly into the C.I. slot on the unit first. Then, insert the viewing card into the reader. ] again to show the teletext in Note: • To enlarge fonts, press [ (expand)]. • To select teletext subpages, press [ (sub page)]. • To directly select the page numbers shown at the bottom of the TV screen, use [RED/GREEN/ YELLOW/BLUE]. • To call up the hidden information, press [ (reveal)]. • To go back to the start page, press [ (index)]. C. I. NENT AUDIO L 3) Press [ (text) / R ] to turn off the teletext decoder. 3) Plug this unit into an AC outlet and press [ (standby-on)] to turn on the unit. Digital Teletext 4) Press [MENU] to display the menu. DTV 5) Press [K / L] to select “DETAIL”, then press [OK]. Some digital TV channels have digital teletext called MHEG (Multimedia and Hypermedia Expert Group). You can see the MHEG data service on the TV screen. 1) Press [ (text) / 6) Press [K / L] to select “CI Menu”, then press [OK]. 7) Follow the instructions on the TV screen. ] to turn on the digital teletext. Note: • In case of failure, you need to call your CI service 2) MHEG information will appear. 3) Follow the instructions on the TV screen. • You can turn off the digital teletext using [ again. (text) / provider. • Menu operations may vary depending on the viewing card. Refer to the manual accompanying the viewing card. ] Colour System Note: Press [RED/GREEN/YELLOW/BLUE] following the instructions on the TV screen. You can change the TV colour system in video or scart mode. Press [COLOUR SYSTEM / ] to change the TV colour system. • Each time you press [COLOUR SYSTEM / ], the TV screen will change as follows. AUTO, PAL, PAL60, SECAM, NTSC, NTSC4.43 Note: When you select “AUTO” by pressing [COLOUR SYSTEM / ], this unit will distinguish the system automatically according to the input signal from the external devices. 11 EN OPERATIONS Watching a TV Programme To cancel the sleep timer DTV ATV Press [ (sleep) / To select a channel ] repeatedly until “Sleep Off” will appear. Sleep Off Press [TV/DTV] to switch digital or analogue mode. Note: If you disconnect the unit from the AC outlet or if a power failure occurs, the sleep timer will be cancelled. DTV Press [P (prog.)] repeatedly to select your desired channel. or Press [the Number buttons] to enter a channel number as three digits for quicker access. e.g.) If you want to select the channel 24, press [0] first, then press [2] and [4] within 3 seconds. /P Switching the Input Mode DTV ATV Press [P 1) Press [AV]. • “Select Input” menu will appear. (prog.)] repeatedly to select your desired channel. or Press [the Number buttons] to enter a channel number as two digits for quicker access. e.g.) If you want to select the channel 24, press [2] and [4] within 3 seconds. /P Select Input 1. DTV 2. ATV 3. Video 4. SCART 5. Component 6. HDMI 7. PC To adjust the volume Press [ +/ – (vol.)] to adjust the audio volume. • You can see the volume bar while adjusting the volume. Volume Press [ 2) Press [K / L] to select the input mode you want, then press [OK]. 20 (mute)] to turn on or off the sound right away. • You can recover the original volume by pressing [ again or [ +/ – (vol.)] . Note: • To watch the digital channel, select “DTV”. (mute)] • To watch the analogue channel, select “ATV”. • To use the video or S-VIDEO input jack on the unit, select “Video”. • To use the SCART jack on the unit, select “SCART”. • To use the COMPONENT (Y/Pb/Pr) input jack on the unit, select “Component”. • To use the HDMI-IN jack on the unit, select “HDMI”. • To use the PC-IN (RGB) jack on the unit, select “PC”. Mute Sleep Timer DTV ATV You can set the unit to be turned off automatically after a set time period. 1) Press [ (sleep) / ]. • Sleep timer display will appear. 2) Press [ (sleep) / ] repeatedly to change the sleep time period. • Each time you press [ (sleep) / ], the timer increases by 30 minutes up to 120 minutes. Sleep EN ATV You can switch the input mode to digital mode, analogue mode or external input mode. 30min. 12 Sound Select DTV TV Screen Information ATV Press [ (sound) / sound mode. DTV ] repeatedly to cycle through the available ATV You can see the broadcasting information. Press [I (information)]. • TV screen information menu will appear. DTV DTV STEREO LEFT MONO RIGHT The Sounds 09:37 Hit Music Special Characteristics : 018 English 07:00-09:59 You're turned to the Sounds, keep it here for the biggest sounds around, it doesn't get fresher than this! Call 09012 345 678 now to select a video 576i SD 4:3 1 Channel name “STEREO” Outputs stereo sound 2 Present programme name / time “LEFT” Outputs left sound 4 Programme information 3 Category name 5 Time 6 Channel number “RIGHT” Outputs right sound 7 Audio language 8 Resolution / Format / TV aspect ratio “MONO” Outputs monaural sound 9 TV/Radio Digital Teletext 10 Teletext 11 Lock status 12 Parental rating ATV 13 Pay TV 14 Subtitle Main Sub MONO Main/Sub Note: When the programme information consists of more than 4 lines, press [K / L] to scroll. ATV “Main” Outputs main sound 2 “Sub” Outputs second sound 1 1 4:3 3 MONO 576i SD 1 Channel number “Main/Sub” Outputs main and sub sound 2 Audio mode 3 Resolution / Format / TV aspect ratio “MONO” Outputs monaural sound In external input mode, the following TV screen information will appear. Note: Available sound modes differ depending on a e.g.) “SCART” programme. SCART 576i SD 4:3 Press [I (information)] again or [BACK] to exit. • TV screen information menu will automatically disappear in a few seconds. 13 EN Changing the TV Screen Display Mode For 16:9 video signal DTV ATV You can select your favourite TV screen size in both 4:3 and 16:9 TV aspect ratios. “Full” “Auto” Press [ZOOM / ] repeatedly to switch the TV screen display mode. • You may not switch the TV screen display mode depending on the programme. “Zoom3” “Zoom1” For 4:3 video signal “Regular” “Zoom2” “Auto” “14:9” “Full” “Auto” Displays a picture at its size depending on the signal automatically. “Panoramic” “Full” Displays a 16:9 picture at its original size. “Cinema” “Zoom1” Displays a 16:9 picture at its maximum size without changing its horizontal and vertical ratio. “Zoom2” Displays a vertically stretched picture. “Auto” Displays a picture at its size depending on the signal automatically. “Zoom3” Displays a horizontally stretched picture. “Regular” Displays a 4:3 picture at its original size. Sidebars appear on both edge of the TV screen. For PC input signal “Regular” “Full” “Full” Displays a 4:3 picture at a 16:9 size; the picture is stretched horizontally to fill the TV screen. “Cinema” Displays a 4:3 picture at a 16:9 size; the picture is stretched horizontally and vertically to fill the TV screen. This crops out the top and bottom of the picture. “Dot By Dot” “Panoramic” Displays a 4:3 picture at a 16:9 size; the centre of the picture is at its original size and the edges stretched horizontally to fill the TV screen. “Regular” Displays a proportionally stretched picture. Sidebars appear on both edges of the TV screen. “14:9” Displays a 4:3 picture at a 14:9 size. Sidebars will be displayed on both edge of the TV screen. “Full” Displays a picture that is stretched out of proportion to fill the TV screen. “Dot By Dot” Displays a picture in its original size. Note: You may not select “Regular” depending on the aspect ratio of the PC input signal. EN 14 Channel List DTV Channel Edit ATV DTV You can easily find a channel you want. ATV You can select a channel, change the channel order, delete the channel, etc. 1) Press [OK] while watching a programme. • Channel list will appear. 1) Press [MENU] to display the menu. 2) Press [K / L] to select “CHANNEL”, then press [OK]. e.g.) Digital 3) Press [K / L] to select “Channel List”, then press [OK]. Channels List-DTV e.g.) Digital 18. The Sounds 19. Cinema 20. Drama EXIT 21. Today's News Channel List Channels List-DTV 22. The Musical PICTURE 18. The Sounds 38. Motors 19. Cinema SOUND Select OK DTV/Radio BACK 20. Drama Back 21. Today's News CHANNEL 22. The Musical DETAIL e.g.) Analogue 38. Motors LANGUAGE Select OK DTV/Radio BACK Back Channels List-ATV P01.TV01 P01.TV01 P01.TV01 P02.TV02 P02.TV02 e.g.) Analogue EXIT Channel List Channels List-ATV PICTURE BACK Select OK SOUND BACK BACK P01.TV01 P01.TV01 P01.TV01 P02.TV02 P02.TV02 Back CHANNEL DETAIL 2) Press [K / L] to select the channel you want to watch. LANGUAGE Select 3) Press [OK] or [BACK] to exit. Note: You can edit the channel list. Refer to “Channel Edit” on BACK BACK OK BACK Back To allocate the decoder page 15 to page 17. ATV Some TV stations transmit encoded TV signals which can only be viewed with a purchased or hired decoder. You can connect such a decoder to SCART jack of the unit. This function will automatically activate the connected decoder for the channel. 4) Press [K / L] to select the channel you want to allocate the decoder, then press [B]. 5) Press [K / L] to select “Decoder”. 6) Press [OK] to decoder on or off. • “ ” will appear on the left of the channel. EXIT Channel List Channels List-ATV PICTURE P01.TV01 P01.TV01 P01.TV01 P02.TV02 P02.TV02 SOUND CHANNEL DETAIL LANGUAGE Select BACK BACK OK BACK Back 7) Press [MENU] to exit. 15 EN To skip the channel DTV To delete the channel ATV DTV 4) Press [K / L] to select the channel you want to skip, then press [B]. 5) Press [K / L] to select “Skip”, then press [OK]. • “ ” will appear on the left of the channel. ATV 4) Press [K / L] to select the channel you want to delete, then press [B]. 5) Press [K / L] to select “Delete”, then press [OK]. • Confirmation window will appear. e.g.) Digital e.g.) Digital EXIT Channel List EXIT Channels List-DTV PICTURE Channel List Channels List-DTV 18. The Sounds PICTURE 18. The Sounds 19. Cinema SOUND 20. Drama SOUND 21. Today's News CHANNEL Select 21. Today's News BACK Confirm DETAIL OK DTV/Radio BACK 38. Motors Back LANGUAGE 6) Press [MENU] to exit. • When using [P /P skipped. Back 22. The Musical 38. Motors LANGUAGE Delete the service? 20. Drama CHANNEL 22. The Musical DETAIL 19. Cinema Select OK DTV/Radio BACK Back 6) Press [OK] to confirm. • The selected channel will be deleted from the memorised channel. (prog.)], the channel will be 7) Press [MENU] to exit. If you want to cancel 4) Press [K / L] to select the channel set to be skipped, then press [B]. 5) Press [K / L] to select “Skip”, then press [OK]. • “ ” will disappear. To change the channel order manually To lock the channel DTV DTV ATV ATV 4) Press [K / L] to select the channel you want to move, then press [B]. 4) Press [K / L] to select the channel you want to lock, then press [B]. 5) Press [K / L] to select “Move Up” or “Move Down”, then press [OK]. • The channel will move one line up or down. 5) Press [K / L] to select “Lock”, then press [OK]. • Password input field will appear. 6) Press [the Number buttons] to enter the 4-digit number for your password. • “ ” will appear on the left of the channel. e.g.) Analogue EXIT EXIT PICTURE Channel List Channels List-ATV PICTURE Channel List Channels List-ATV e.g.) Analogue P01.TV01 P01.TV01 P01.TV01 P02.TV02 P02.TV02 P02.TV02 P01.TV01 P01.TV01 P02.TV02 P02.TV02 Decoder Skip SOUND Lock Delete CHANNEL Sort:Ch No Sort:Frequency Move Up DETAIL SOUND LANGUAGE Select BACK OK Move Down BACK Back CHANNEL DETAIL LANGUAGE Select BACK OK BACK BACK 6) Press [MENU] to exit. Back Note: To watch the channel, press [K / L] to select the channel you want to watch, then press [OK] at the step 3. 7) Press [MENU] to exit. • When you select the locked channel, you need to enter the password to watch. If you want to unlock 4) Press [K / L] to select the locked channel, then press [B]. 5) Press [K / L] to select “Unlock”, then press [OK]. • Password input field will appear. 6) Press [the Number buttons] to enter the 4-digit number. • “ ” will disappear. 7) Press [MENU] to exit. EN 16 EPG (Electronic Programme Guide) To change the channel order automatically DTV DTV You can easily find a channel or see the detailed channel information. EPG (Electronic Programme Guide) gives you scheduled information of the TV programmes. 4) Press [B]. 5) Press [K / L] to select “Sort:LCN” , “Sort:Name Down”, or “Sort:Name Up”, then press [OK]. Press [GUIDE]. • You can also display EPG as follows. 1) Press [MENU] to display the menu. “Sort:LCN” Arrange in channel number. “Sort:Name Down” Arrange in alphabetical order (A-Z). 2) Press [K / L] to select “CHANNEL”, then press [OK]. 3) Press [K / L] to select “EPG”, then press [OK]. • EPG will appear. “Sort:Name Up” Arrange in alphabetical order (Z-A). EXIT Special Channels List-DTV PICTURE Sort:LCN 18. The Sounds CHANNEL DETAIL 1 Sort:Name Down 19. Cinema SOUND 20. Drama Sort:Name Up Skip 21. Today's News Delete 22. The Musical Lock Move Up 38. Motors Select OK DTV/Radio BACK 09:00-09:59 BB Special: Mr.Smith introduces unseen items from previous programmes in the series and talks to expect Mrs. Cole about the history of BB House. Thu 01/12/2005 3 Move Down LANGUAGE Thu 01/12/2005 09:37 EPG Channel List Back The Sounds Cinema Drama Today's News The Musical Page+ Select 09:30 2 10:00 Hit Music Special Drama's Daily News Triangle 10:30 Pick Up Number Our Home The Frying Winem Morning News Dog&Cats Page- Prev. Day Invoke CH. EPG Detail 4 Next Day BACK Back 6) Press [MENU] to exit. 1 Programme information 2 Picture window ATV 4) Press [B]. 3 Channel list 5) Press [K / L] to select “Sort:Ch No” or “Sort:Frequency”, then press [OK]. 4 Programme list Press [K / L / s / B] to select a programme. • Press [RED] or [GREEN] to scroll down or up the channel list. • Press [YELLOW] or [BLUE] to move the programme list to the previous or next day. “Sort:Ch No” Arrange in channel number. “Sort:Frequency” Arrange in channel frequency. EXIT Press [OK] to watch the selected programme if it is currently available. Channel List Channels List-ATV PICTURE Decoder P01.TV01 P01.TV01 P02.TV02 P02.TV02 Skip SOUND Lock Delete CHANNEL Sort:Ch No Select the programme, then press [I (information)] to display more detailed programme information. Sort:Frequency LANGUAGE EPG Detail Move Up DETAIL Select OK BACK BACK Move Down Back 09:00-09:59 Cinema BB Special: Mr.Smith introduces unseen items from previous programmes in the series and talks to expect Mrs. Cole about the history of BB House. 6) Press [MENU] to exit. Select EPG BACK Back Press [GUIDE] or [BACK] to exit. 17 EN OTHER SETTINGS DTV ATV Picture Adjustment “Reset Settings” Press [K / L] to select “Reset”, then press [OK] to restore the picture settings to the default. You can adjust the picture settings according to your personal preference. These settings are automatically stored after exiting the picture menu. EXIT 1) Press [MENU] to display the menu. PICTURE 2) Press [K / L] to select “PICTURE”, then press [OK]. SOUND 3) Press [K / L] to select the item you want, then press [OK]. CHANNEL Reset Settings This function resets the setting for current Picture Mode to factory default. Cancel Reset DETAIL 4) Adjust the picture quality. LANGUAGE “Picture Mode” Press [K / L] to select the setting (“Standard, Dynamic, Movie, News”) you want, then press [OK]. “Color Temp.” Press [K / L] to select the setting (“Cool, Neutral, Warm”) you want, then press [OK]. Picture EXIT PICTURE SOUND Picture Mode Standard Brightness Contrast Dynamic CHANNEL EXIT Movie News Color PICTURE Tint Sharpness Brightness Contrast SOUND Reset Settings DETAIL Picture Picture Mode Color Temp. Color Tint CHANNEL LANGUAGE Sharpness DETAIL Reset Settings Cool Color Temp. Neutral Warm LANGUAGE “Brightness, Contrast, Color, Tint, Sharpness” Press [s / B] to adjust. Setting “Brightness” Brightness OK OK decrease brightness increase brightness Move OK OK decrease contrast increase contrast Move OK OK decrease colour increase colour add red add green Move OK OK make soft make clear Move OK OK “Contrast” 30 Contrast Adjust “Color” 30 Color Adjust [B] Move 30 Adjust [s] 5) Press [MENU] to exit. “Tint” 0 Tint Adjust “Sharpness” Sharpness 30 Adjust Note: • Press [K / L] to change the items. • You can adjust “Tint” only when receiving NTSC signals from the connected external device. EN 18 Sound Adjustment Lock Setting You can adjust the sound settings according to your personal preferences. These settings are automatically stored after exiting the sound menu. You can lock the channel or set the parental rating to avoid watching an inappropriate programme. 1) Press [MENU] to display the menu. 1) Press [MENU] to display the menu. 2) Press [K / L] to select “DETAIL”, then press [OK]. 2) Press [K / L] to select “SOUND”, then press [OK]. 3) Press [K / L] to select “Lock Setting”, then press [OK]. 3) Press [K / L] to select the item you want, then press [OK]. 4) Press [the Number buttons] to enter the 4-digit number. 4) Adjust the sound quality. EXIT “Treble, Bass” Press [s / B] to adjust. Lock Setting PICTURE SOUND Enter password. [s] Setting [B] CHANNEL “Treble” DETAIL 0 Treble Adjust LANGUAGE Move OK decrease “Bass” Bass BACK Back increase • If you have not set up your password, enter 0000. 0 Adjust PIN Code OK Move OK OK 5) Press [MENU] to exit. Note: Press [K / L] to change the settings. Note: If the locked channel is found during the channel scanning, you need to enter the password. “Reset Settings” Press [K / L] to select “Reset”, then press [OK] to restore the sound settings to the default. EXIT PICTURE To set the new password 5) Press [K / L] to select “Change Password.”. 6) Press [the Number buttons] to enter the new 4-digit number. Reset Settings This function resets the Sound settings to factory default. Cancel Reset 7) Press [the Number buttons] to enter the same 4-digit number again. SOUND CHANNEL DETAIL EXIT LANGUAGE PICTURE Change Password Enter password. SOUND Confirm password. 5) Press [MENU] to exit. CHANNEL DETAIL LANGUAGE PIN Code BACK Back • After entering the password, “Lock Setting” menu will appear. 8) Press [MENU] to exit. To set the parental rating 5) Press [K / L] to select “Parental Rating”. 6) Press [K / L] to select your desired parental rating. EXIT Lock Setting PICTURE SOUND Parental Rating Change Password No Block 4 5 CHANNEL 6 7 DETAIL LANGUAGE 8 9 7) Press [MENU] to exit. 19 EN PC Settings Time Zone You can adjust the PC screen position, clock and phase. Make sure your PC is connected. You can set the time zone according to the resident area. 1) Press [MENU] to display the menu. 1) Press [MENU] to display the menu. 2) Press [K / L] to select “DETAIL”, then press [OK]. 2) Press [K / L] to select “DETAIL”, then press [OK]. 3) Press [K / L] to select “Time Zone”, then press [OK]. 3) Press [K / L] to select “PC Settings”, then press [OK]. 4) Press [K / L] to select the time difference you want, then press [OK]. 4) Press [K / L] to select the item you want, then press [OK]. 5) Adjust the settings. EXIT “Auto Adjustment” Press [K / L] to select “Adjust”, then press [OK]. PICTURE 0 Time Zone +1 CHANNEL CI Menu +2 Transparency +3 Factory Preset This function automatically adjusts the position, clock and phase of the picture element. PICTURE +4 DETAIL Cancel Auto PC Settings SOUND Auto Adjustment EXIT Detail Lock Setting +5 Adjust LANGUAGE SOUND CHANNEL 5) Press [MENU] to exit. DETAIL LANGUAGE Transparency • Each setting will be adjusted automatically. You can set the menu transparent level. 1) Press [MENU] to display the menu. “Horizontal Position, Vertical Position” Press [s / B] to adjust. [s] [B] OK move PC screen left move PC screen right OK move PC screen down move PC screen up Setting “Horizontal Position” 0 H. Position Adjust Move OK 0 Adjust Move 4) Press [K / L] to select the transparent level you want, then press [OK]. EXIT “Vertical Position” V. Position 2) Press [K / L] to select “DETAIL”, then press [OK]. 3) Press [K / L] to select “Transparency”, then press [OK]. OK PICTURE Detail Lock Setting 0 PC Settings -1 SOUND Time Zone CHANNEL CI Menu Transparency DETAIL “Clock, Phase” Factory Preset -2 -3 -4 -5 -6 LANGUAGE Press [s / B] to adjust. Setting [s] [B] decrease setting value increase setting value 5) Press [MENU] to exit. “Clock” 0 Clock Adjust Move OK OK Move OK OK “Phase” Phase Factory Preset You can restore all the settings to the default. 42 Adjust 1) Press [MENU] to display the menu. 2) Press [K / L] to select “DETAIL”, then press [OK]. 6) Press [MENU] to exit. 3) Press [K / L] to select “Factory Preset”, then press [OK]. 4) Press [K / L] to select “Reset”, then press [OK]. • All the settings are restored to the default. Note: Press [K / L] to change the items. 5) Press [MENU] to exit. EN 20 MAINTENANCE Panel Cleaning Cabinet Cleaning • If the LCD panel should require cleaning, wipe it with a cotton or soft cloth. Before cleaning the panel, disconnect the power cord. • Wipe the front panel and other exterior surfaces of the unit with a soft cloth immersed in lukewarm water and wrung dry. • Never use a solvent or alcohol. Do not spray insecticide liquid near the unit. Such chemicals may cause damage and discoloration to the exposed surfaces. Servicing • Should your unit become inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn the unit off, unplug the power cord, and call our helpline for assistance or contact the retailer. TROUBLESHOOTING GUIDE Is unit plugged in? Power at outlet? Is unit’s [ Lines or Streaks in Picture Ghosts in picture Picture Blurred Sound OK, Picture Poor Picture OK, Sound Poor × × × × × × × × × (standby-on)] on? × Is antenna connected to terminal on the back of the set? If outside antenna is being used, check for broken wire. × Check for local interference. × Turn off with [ × Forget the password Weak Picture × Black or Luminous point on TV screen Poor Reception on Some Channels × Different colour marks on TV screen No Colour × × No Picture or Sound Picture Rolls Vertically Try a new channel, if OK, then possibly due to poor channel reception. Picture Distorted POSSIBLE REMEDY Bars On TV screen PROBLEM QUICK SERVICE CHECK LIST Remote Control Doesn’t Work Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked possibilities. Before arranging for service, check these items. It could save you time and money. × × × × × × × × × × × × × × × × × × × × (standby-on)] and then turn it on after about a minute. × × × Adjust COLOUR control. × Adjust Contrast & Brightness control. × Check batteries in Remote Control. × × Move the unit away from the nearby appliances that generate strong magnetic field. Turn off using [ (standby-on)], then turn it on again 30 minutes or so later. Surrounding temperature is too low. × × Life of the Back Light is approximately 50,000 hours. Ask the Service Centre to replace. It is quality of the LCD Panel. × × × × × Reset to the factory default, and the password will restore to "0000". Refer to "Factory Preset" on page 20. 21 × EN SPECIFICATIONS General Specifications Other Specifications Television system: Remote control: Terminals Headphone: S-Video input: Video input: Audio input: PC input: AUDIO/VIDEO: Component Video input: HDMI input: Stereo Sound System 2 speakers Sound output: EN PAL I TV standard PAL B/G TV standard PAL D/K TV standard SECAM L TV standard SECAM L' TV standard SECAM B/G TV standard SECAM D/K TV standard Power requirements: Power consumption: LCD: Dimensions (H x W x D) (without stand): (with stand): Weight (without stand): (with stand): 1/8 inches (3.5mm) Mini DIN 4-pin jack x 1 RCA jack x 1 RCA jack x 4 D-Sub 15pin x1 (RGB) Mini jack Ø3.5mm x 1 (AUDIO) 21 pin scart jack with RGB Input x 1 Digital encoded infrared light system AC 220-240 V~, 50 Hz 68 W 19" 345.3mm x 475mm x 94.5mm 384.6mm x 475mm x 190mm 4.1 kg 4.4 kg • Designs and specifications are subject to change without notice and without our legal obligation. RCA jack x 3 Y : 1Vp-p x 1 Pb : 700mVp-p x 1 Pr : 700mVp-p x 1 HDMI 19pin x 1 1 W, 8 ohm x 2 22 When does switchover happen? Keep this important information about how to re-tune your TV during the digital TV switchover *Copeland switches on October 17, 2007 The exact date you switch depends on the transmitter you are served by. To check when you switch, go to Digital UK’s postcode checker on www.digitaluk.co.uk Keep this leaflet and your Owner’s Manual safe – you’ll need them ............................................... Check your ITV news service or look at Teletext page 106 to see what TV region you’re in. Visit us at digitaluk.co.uk call us on 0845 6 50 50 50† †Calls charged at BT rate of 3p per minute daytime and 1p per minute evenings and weekends. Rates may vary for calls from non-BT lines. How to re-tune: Television in the UK is going digital, bringing us all more choice and new services. Starting in late 2007 and ending in 2012, television services in the UK will go completely digital, TV region by TV region. To find out how to re-tune your TV, refer to “Auto Scan” on page 9. Please see overleaf to find out when your area switches to digital. If you are missing any channels, it may be that they are not available in your area, or that your aerial needs upgrading. Digital UK is the independent, non-profit organisation leading the process of digital TV switchover in the UK. Digital UK provides impartial information on what people need to do to prepare for the move to digital, and when they need to do it. If you have any questions, please contact your equipment supplier or call Digital UK on 0845 6 50 50 50 or visit www.digitaluk.co.uk How the switchover affects your TV equipment: Your new TV has a digital tuner built in, which means it is ready to receive the Freeview signal by simply plugging it into your aerial socket (check if you can get digital TV through your aerial now, or whether you’ll have to wait until switchover, at www.digitaluk.co.uk). When the TV switchover happens in your area, there are at least two occasions when you will need to re-tune your TV in order to continue receiving your existing TV channels, and also to pick up new ones. Digital UK, the body leading the digital TV switchover, will advise you when you need to re-tune during the switchover. If you choose to connect your TV to satellite or cable with a digital box then it will not be affected by switchover, and you won’t need to re-tune. 23 EN For users in the UK : If you have any problems setting up your new TV, please call the Helpline on 0870 330 5000. For users in the Republic of Ireland : If you have any problems setting up your new TV, please call the Helpline on 1890-582500. Printed in Poland © 2009 Victor Company of Japan, Limited 0109TKH-FU-FU 1EMN24540 / A8CN9BP
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Fill forms, Extract, Assemble, Print high-res Modify Date : 2008:12:08 11:48:48+09:00 Create Date : 2008:12:01 14:28:23Z Subject : 1EMN24540_EN Page Count : 24 Creation Date : 2008:12:01 14:28:23Z Mod Date : 2008:12:08 11:48:48+09:00 Producer : Acrobat Distiller 5.0.5 (Windows) Author : JVC Metadata Date : 2008:12:08 11:48:48+09:00 Creator : JVC Title : LT-19DA9BJ Description : 1EMN24540_EN Page Mode : UseOutlines Page Layout : SinglePageEXIF Metadata provided by EXIF.tools