JVC LT 32DG20J User Manual 50164104 EN

User Manual: JVC LT-32DG20J LT-32DG20J English,

Open the PDF directly: View PDF .
Page Count: 32

LT-32DG20J

©2010 Victor Company of Japan, Limited 0410TMH-VT-VT

50164104

INSTRUCTIONS

WIDE LCD PANEL TV

ENGLISH

If something doesn't seem to work

If there is something about your appliance which you do

not understand and you live in the UK you can

Phone our help line during normal office hours on:

0844 8009595

Calls are charged at standard rates.

We apologise for any inconvenience caused by minor

inconsistencies in these instructions, which may occur

as a result of product improvement and development.

Kesa U.K HU1 3AU 29 / 04 / 2008

䄰ㅟ孇䉝彍䈴㕍彃佖䕒弱〰㘷㐶ㅟ㔰ㄶ㐱〴

〶⁎楳慮′〱〠卡泽‱㘺㌴㨰

English - 1 -

Dear Customer,

This apparatus is in conformance with the valid European directives and standards regarding electromagnetic

compatibility and electrical safety.

European representative of Victor Company of Japan, Limited is:

JVC Technical Services Europe GmbH

Postfach 10 05 04

61145 Friedberg

Germany

Information for Users on Disposal of Old Equipment and Batteries

[European Union]

These symbols indicate that the electrical and electronic equipment and the battery with this

symbol should not be disposed of as general household waste at its end-of-life. Instead,

the products should be handed over to the applicable collection points for the recycling

of electrical and electronic equipment as well as batteries for proper treatment, recovery

and recycling in accordance with your national legislation and the Directive 2002/96/EC

and 2006/66/EC.

By disposing of these products correctly, you will help to conserve natural resources and

will help to prevent potential negative effects on the environment and human health which

could otherwise be caused by inappropriate waste handling of these products.

For more information about collection points and recycling of these products, please contact

your local municipal offi ce, your household waste disposal service or the shop where you

purchased the product.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national

legislation.

[Business users]

If you wish to dispose of this product, please confi rm attached “KESA ELECTRICALS

SAFETY INSTRUCTIONS” to obtain information about the take-back of the product.

[Other Countries outside the European Union]

These symbols are only valid in the European Union.

If you wish to dispose of these items, please do so in accordance with applicable national

legislation or other rules in your country for the treatment of old electrical and electronic

equipment and batteries.

Notice:

The sign Pb below

the symbol for

batteries indicates

that this battery

contains lead.

Products

Battery

Logo & License

HDMI, the HDMI Logo, and High-Defi nition Multimedia Interface are trademarks or registered trademarks of

HDMI Licensing LLC in the United States and other countries.

DVB is a registered trademark of the DVB Project

TRADEMARK ACKNOWLEDGMENT

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 1A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 1 08.04.2010 08:52:4208.04.2010 08:52:42

English - 2 -

Contents

IDTV Menu System .............................................. 13

Channel List ...................................................... 13

Timers ............................................................... 15

Conditional Access ........................................... 15

TV Setup ........................................................... 15

Setup ................................................................ 16

Analogue TV Menu System .................................. 19

Picture Menu..................................................... 19

Sound Menu ..................................................... 20

Feature Menu ................................................... 21

Install Menu ...................................................... 22

Source Menu .................................................... 23

PC Mode Menu System........................................ 23

PC Position Menu ............................................. 23

Displaying TV Information .................................... 24

Muting Function .................................................... 24

Freezing Picture ................................................... 24

Zoom Modes......................................................... 24

Auto .................................................................. 24

16:9 ................................................................... 24

4:3 ..................................................................... 25

Panoramic......................................................... 25

14:9 ................................................................... 25

Cinema ............................................................. 25

Subtitle .............................................................. 25

Zoom................................................................. 25

Teletext ................................................................. 25

Tips ....................................................................... 26

Image Persistence ............................................ 26

No Power .......................................................... 26

Poor Picture ...................................................... 26

No Picture ......................................................... 26

Sound ............................................................... 26

Remote Control................................................. 26

Input Sources.................................................... 26

Appendix A: PC Input Typical Display Modes ....... 27

Appendix B: AV and HDMI Signal Compatibility

(Input Signal Types) .............................................. 28

Specifi cations ....................................................... 29

Important Instruction ............................................. 30

Logo & License ....................................................... 1

Accessories ............................................................ 3

Features ................................................................. 3

Introduction ............................................................. 3

Preparation ............................................................. 3

Safety Precautions ................................................. 4

Power Source ..................................................... 4

Power Cord ......................................................... 4

Moisture and Water ............................................ 4

Cleaning.............................................................. 4

Heat and Flames ................................................ 4

Lightning ............................................................. 4

Replacement Parts ............................................. 4

Servicing ............................................................. 4

Waste Disposal ................................................... 4

Disconnecting the Device ................................... 4

Headphone Volume ............................................ 4

Installation........................................................... 4

LCD Screen ........................................................ 4

Warning .............................................................. 5

Inserting Batteries into the Remote Control Handset ..5

Operating Range for the Remote Control ............... 5

Overview of the Remote Control ............................ 6

LCD TV and Operating Buttons .............................. 7

Viewing the Connections- Back Connectors .......... 7

Viewing the Connections - Side Connectors .......... 8

Using the Cable Holder .......................................... 8

Power Connection .................................................. 8

Aerial Connection ................................................... 8

Connecting the LCD TV to a PC ............................. 9

Connecting to a DVD Player................................... 9

Using Side AV Connectors ................................... 10

Connecting Other Equipment via SCART ............ 10

Switching the TV On/Off ....................................... 10

To Switch the TV On ......................................... 10

To Switch the TV Off ......................................... 10

Input Selection ...................................................... 10

Basic Operations ...................................................11

Operation with the Buttons on the TV ................11

Initial Settings ........................................................11

General Operation ................................................ 12

Electronic Programme Guide (EPG) .................... 12

Displaying Subtitles .......................................... 12

Digital Teletext (** for UK only) ......................... 12

Analogue Teletext ............................................. 13

Widescreen ....................................................... 13

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 2A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 2 08.04.2010 08:52:4308.04.2010 08:52:43

English - 3 -

Accessories

Remote Controller

Batteries: 2 X AAA

Instruction Book

Quick Guide

Cable Holder

Features

• Remote controlled colour LCD TV.

• Fully integrated digital TV (DVB-T).

• HDMI connectors for digital video and audio. This

connection is also designed to accept high defi nition

signals.

• 200 programmes from VHF, UHF(analogue).

• 500 programmes for digital mode (IDTV).

• OSD menu system.

• SCART socket for external devices (such as video,

video games, audio set, etc.).

• Stereo sound system.

• Teletext, fastext, TOP text.

• Headphone connection.

• Automatic programming system.

• Forward or backward manual tuning.

• Sleep timer.

• Child lock.

• Automatic sound muting when no transmission.

• NTSC playback.

• AVL (Automatic Volume Limiting).

• When no valid signal is detected, after 5 minutes the

TV switches automatically to standby mode.

• PLL (Frequency Search).

• PC input.

• Plug&Play for Windows 98,ME,2000,XP, Vista,

Windows7.

• Game Mode

Introduction

Thank you for choosing this product. This manual will

guide you for the proper operation of your

TV. Before operating the TV, please read

this manual thoroughly.

Please do keep this manual in a safe place

for future references.

Preparation

For ventilation, leave a free space of at least 10 cm

all around the set. To prevent any fault and unsafe

situations, please do not place any objects on top

of the set.

Use this device in moderate climates.

10 cm

10 cm

10 cm

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 3A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 3 08.04.2010 08:52:4308.04.2010 08:52:43

English - 4 -

fl ame sources, such as lighted candles, are placed

on top of the TV.

Warning

To prevent the spread of fi re, keep candles or other

open fl ames away from this product at all times.

Lightning

In case of storm and lightning or when

going on holiday, disconnect the power

cord from the wall outlet.

Replacement Parts

When replacement parts are required, make sure that

the service technician has used replacement parts,

which are specifi ed by the manufacturer or have the

same specifi cations as the original one. Unauthorized

substitutions may result in fi re, electrical shock or

other hazards.

Servicing

Please refer all servicing to qualified

personnel. Do not remove the cover

yourself as this may result in an electric

shock.

Waste Disposal

Instructions for waste disposal:

• Packaging and packaging aids are recyclable and

should principally be recycled. Packaging materials,

such as foil bag, must be kept away from children.

• Batteries, including those which are heavy metal-

free, should not be disposed of with household

waste. Please dispose of used battery in an

environment friendly manner. Find out about the

legal regulations which apply in your area.

• Cold cathode fluorescent lamp in LCD PANEL

contains a small amount of mercury; please follow

the local laws or regulations for disposal.

Disconnecting the Device

The mains plug is used to disconnect TV set from

the mains and therefore it must remain readily

operable.

Headphone Volume

Excessive sound pressure from earphones

and headphones can cause hearing loss.

Installation

To prevent injury, this device must be securely

attached to the wall in accordance with the installation

instructions when mounted to the wall (if the option

is available).

LCD Screen

The LCD panel is a very high technology product with

about a million thin fi lm transistors, giving you fi ne

picture details. Occasionally, a few non-active pixels

Safety Precautions

Please read the following recommended

safety precautions carefully for your

safety.

Power Source

The main power supply for this TV is controlled by

inserting or removing the power plug.

The TV set should be operated only from a 220-240

V AC, 50 Hz outlet. Ensure that you select the correct

voltage setting for your convenience.

Power Cord

Do not place the set, a piece of furniture, etc. on the

power cord (mains lead) or pinch the cord. Handle the

power cord by the plug. Do not unplug the appliance

by pulling from the power cord and never touch the

power cord with wet hands as this could cause a short

circuit or electric shock. Never make a knot in the cord

or tie it with other cords. The power cords should be

placed in such a way that they are not likely to be

stepped on. A damaged power cord can cause fi re or

give you an electric shock. When it is damaged and

needs to be replaced, it should be done by qualifi ed

personnel.

Make enough room for inserting and removing the

power plug.

Place the TV as close to the outlet as possible.

Moisture and Water

Do not use this device in a humid and

damp place (avoid the bathroom, the

sink in the kitchen, and near the washing

machine). Do not expose this device to

rain or water, as this may be dangerous

and do not place objects fi lled with liquids,

such as fl ower vases, on top. Avoid from

dripping or splashing.

If any solid object or liquid falls into the cabinet, unplug

the TV and have it checked by qualifi ed personnel

before operating it any further.

Cleaning

Before cleaning, unplug the TV set

from the wall outlet. Do not use liquid or

aerosol cleaners. Use soft and dry cloth.

Ventilation

The slots and openings on the TV set are intended for

ventilation and to ensure reliable operation. To prevent

overheating, these openings must not be blocked or

covered in anyway.

Heat and Flames

The set should not be placed near to open

fl ames and sources of intense heat such

as an electric heater. Ensure that no open

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 4A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 4 08.04.2010 08:52:4408.04.2010 08:52:44

English - 5 -

may appear on the screen as a fi xed blue, green or

red point. Please note that this does not affect the

performance of your product.

Warning

Do not leave your TV in standby or operating mode

when you leave your house.

Inserting Batteries into the

Remote Control Handset

• Remove the battery cover located on the back of

the handset by gently pulling backwards from the

indicated part.

• Insert two AAA/R3 or equivalent type batteries

inside. Place the batteries in the right directions and

replace the battery cover.

Note: Remove the battery from remote control handset when

it is not to be used for a long period. Otherwise it can be

damaged due to any leakage of batteries.

Batteries should not be exposed to excessive heat

such as sunshine, fi re or the like.

Operating Range for the

Remote Control

• Point the top of the remote control toward the LCD

TV’s remote sensor LED while pressing a button.

Remote range is approximately 7m/23ft.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 5A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 5 08.04.2010 08:52:4508.04.2010 08:52:45

English - 6 -

Overview of the Remote Control

TV/DTV1. : TV – Digital TV

OK2. : OK / Confi rm / Freezing Picture(in

analogue mode) / Channel list (in DTV mode)

3. : Cursor left

MENU4. : Menu on-off

ZOOM5. : Image size

RED6. : Sound menu / Page Up (**) (in DTV

mode)

GREEN7. : Picture Menu / Page Down (**) (in

DTV mode)

AV8. : Source selection

9. / : Programme up / down

10. : Info

11. : Index Page (in TXT mode)

12. : Expand (in TXT mode)

13. : Hold (in TXT mode)

TV/RADIO14. : Switches between TV and radio

broadcasts.(in DTV mode)

15. : Standby

GUIDE16. : Programme guide

17. : Cursor up

18. : Cursor right

BACK19. : Return

20. : Cursor down

21. : Jump to now (in EPG mode)

BLUE22. : Install Menu / Favourite Mode (in DTV

mode) (*)

YELLOW23. : Feature Menu / Current Language

(in DTV mode) (*)

24. / : Volume up / down

25. : Muting

0,1...8,9 :Numeric buttons.26.

27. : Teletext on / PAT (Picture-and-text) /

Teletext off

28. : Reveal

29. : Time (in analogue mode)

30. : Subtitle on-off

31. : Mono-stereo / Dual I-II

(*) for EU countries only

(**) Scrolls page up or down in DTV Channel list.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 6A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 6 08.04.2010 08:52:4608.04.2010 08:52:46

English - 7 -

LCD TV and Operating Buttons

FRONT and REAR VIEW Control Buttons

Standby button1.

TV/AV button2.

Programme Up/Down 3. buttons

Volume Up/Down buttons4.

Note: Press “ ” /“ ”

buttons at the same time to view main

menu.

Viewing the Connections- Back Connectors

SCART socket inputs or outputs for external devices.1. Connect the SCART cable between SCART socket on TV and SCART socket on your external device

(such as a decoder, a VCR or a DVD player).

Note: If an external device is connected via the SCART socket,

the TV will automatically switch to AV mode.

Note: S-VHS VCR should be connected to EXT-1 and can be

watched from EXT-1S source.

PC Input is for connecting a personal computer to the TV set. 2. Connect the PC cable between the PC INPUT on the TV and

the PC output on your PC. Please do not connect a device to

YPbPr socket while using PC input..

SPDIF3. Coaxial Out outputs digital audio signals of the

currently watched source.

RF Input connects to an antenna or a cable.4. Note that if you use a decoder or a media recorder, you should connect the aerial cable through the

device to the television with an appropriate antenna cable, as shown in the illustration in the following

pages.

HDMI

5. 2: HDMI input

HDMI6. 1: HDMI input

HDMI Input is for connecting a device that has an HDMITM connector.

Your LCD Television is capable of displaying High Defi nition pictures from devices such as a High

Defi nition Satellite Receiver or DVD Player. These devices must be connected via the HDMITM

connector or Component Socket. These sockets can accept either 480i, 480p, 576p, 576i, 720p, 1080i,

1080p signals. No sound connection is needed for an HDMI to HDMI connection.

When you use the wall mount kit (optional) with the LCD TV, we would defi nitely recommend to plug all your cables into the

back of the LCD before mounting to the wall.

SPDIF

SCART

VGA

Coax.OUT

HDMI 2

HDMI 1

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 7A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 7 08.04.2010 08:52:4808.04.2010 08:52:48

English - 8 -

Viewing the Connections -

Side Connectors

CI Slot is used for 1. inserting a CI card. A

CI card allows you to

view all the channels

that you subscribe to.

For more information,

see “Conditional

Access” section.

Component Video 2. Inputs (YPbPr) are

used for connecting

component video.

You can connect the

component video

and audio sockets

with a device that

has component

output. Connect the

component video

cables between the

COMPONENT VIDEO

INPUTS on on the

TV and the component video outputs of your

device. While connecting, be sure that the

letters on your TV, “Y”, “Pb”, “Pr” correspond

with your device’s connectors.

IMPORTANT:Please do not connect a device to

PC socket while using YPbPr input.

Video Input 3. (INPUT FAV) is used for connecting

video signals of external devices.Connect the

video cable between the VIDEO IN socket

on the TV and the VIDEO OUT jack on your

device.

Audio Inputs 4. (INPUT FAV) are used for

connecting audio signals of external devices.

Connect the audio cable between the AUDIO

INPUTS on the TV and the AUDIO OUTPUT

jacks on your device.

Also to enable PC/YPbPr sound connection

in such a case, use an appropriate audio cable

between the connected device’s audio outputs

and the TV’s audio inputs

Note: If you connect a device to the TV via the

VIDEO or PC/YPbPr cable you should also

connect your device with an audio cable to the

AUDIO INPUTS of the TV to enable audio.

Headphone jack is used for connecting an 5. external headphone to the system. Connect to

the HEADPHONE jack to listen to the TV from

headphones.

Standby switch is used for turning the TV on 6. or off.

INPUT AV

Using the Cable Holder

You can use the supplied cable holder as the

following:

• Place the cable holder into the cable holder hole

located on the rear side of the TV as illustrated

above.

• Place cables into the cable holder after all necessary

connections are made.

Power Connection

IMPORTANT: The TV set is designed to operate on

220-240V AC, 50 Hz.

• After unpacking, allow the TV set to reach the

ambient room temperature before you connect the

set to the mains.

• Plug the power cable to the mains socket outlet.

Aerial Connection

• Connect the aerial or cable TV plug to the AERIAL

INPUT socket located at the rear of the TV.

SPDIF

SCART

VGA

Coax.OUT

HDMI 2

HDMI 1

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 8A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 8 08.04.2010 08:52:5008.04.2010 08:52:50

English - 9 -

Connecting the LCD TV to a

PC

For displaying your computer’s screen image on

your LCD TV, you can connect your computer to the

TV set.

• Power off both computer and display before making

any connections.

• Use 15-pin D-sub display cable to connect a PC

to the LCD TV.Use an audio cable between audio

inputs of the TV (side) and audio output of your PC

to enable sound connection.

• When the connection is made, switch to PC source.

See “Input selection” section.

• Set the resolution that suits your viewing requirements.

Resolution information can be found in the appendix

parts.

SPDIF

SCART

VGA

Coax.OUT

HDMI 2

HDMI 1

PC audio cable

(not supplied)

to AUDIO INPUTS

on the TV

PC RGB cable

(not supplied)

to PC input

Audio

Inputs

PC Input

Connecting to a DVD Player

If you want to connect a DVD player to your LCD

TV, you can use connectors of the TV set. DVD

players may have different connectors. Please refer

to your DVD player’s instruction book for additional

information. Power off both the TV and the device

before making any connections.

Note: Cables shown in the illustration are not supplied.

• If your DVD player has an HDMI socket, you can

connect via HDMI. When you connect to DVD player

as illustrated below, switch to HDMI source. See,

“Input Selection” section.

• Most DVD players are connected through

COMPONENT SOCKETS. Use a component

video cable to connect video input. To enable sound

connection, use AUDIO IN located side of the TV

(YPbPr cable is not supplied).

• When the connection is made, switch to YPbPr

source. See, “Input selection” section.

• You may also connect through the SCART socket.

Use a SCART cable as shown below.

HDMI

input

Scart socket

Component

video

inputs

Component

audio

inputs

DVD Player

Note: These methods of connection perform the same

function but in different levels of quality. It is not necessary

to connect by all three methods.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 9A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 9 08.04.2010 08:52:5408.04.2010 08:52:54

English - 10 -

Using Side AV Connectors

You can connect a range of optional equipment

to your LCD TV. Possible connections are shown

below. Note that cables shown in the illustration are

not supplied.

• For connecting a camcorder, connect to the VIDEO

IN socket and the AUDIO SOCKETS. For selecting

the related source, see the section “Input selection”

in the following parts.

• To listen the TV sound from headphones, connect

to the HEADPHONE jack of theTV

Headphone

Connecting Other Equipment

via SCART

Most devices support SCART connection. You can

connect a; DVD recorder, a VCR or a decoder to

your LCD TV by using the SCART socket. Note that

cables shown in the illustration are not supplied.

Power off both the TV and the devices before making

any connections.

For more information, refer to your device’s own

instruction book.

Note: S-VHS VCR should be connected to EXT-1 and can

be watched from EXT-1S source.

Scart socket

Decoder

DVD Recorder Video Recorder

Switching the TV On/Off

To Switch the TV On

• Connect the power cord to the 220-240V AC 50

Hz.

• Switch the “ ” button to position “|” so the TV will

switch to standby mode.

• To switch on the TV from standby mode either:

• Press the “ ” button, / or a numeric button

on the remote control.

• Press the or button on the TV.

The TV will then switch on and the standby LED

lights up.

Note : If you switch on your TV via PROGRAMME UP/DOWN

buttons on the remote control or on the TV set, the programme

that you were watching last will be reselected.

By either method the TV will switch on and the standby

LED lights up.

To Switch the TV Off

• Switch the “ ” button to position 2 as illustrated,

() so the TV will switch OFF.

• To power down the TV completely, unplug the

power cord from the mains socket.

Note: When the TV is switched to standby mode, standby LED

can blink to indicate that features such as Standby Search,

Over Air Download or Timer is active.

Input Selection

Once you have connected external systems to your TV,

you can switch to different input sources.

• Press “AV” button on your remote control for directly

changing sources.

or

• Select “Source” option from the main menu by

using “ ” or “ ” button. Use then “ ” or

“” button to highlight an input and press “ ” button

to select.

Note: You can mark desired source options by pressing the OK

button. Therefore, when “AV” button is pressed, only the marked

source options will be available (except for the TV source).

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 10A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 10 08.04.2010 08:52:5608.04.2010 08:52:56

English - 11 -

Basic Operations

You can operate your TV using both the remote

control and onset buttons.

Operation with the Buttons on the TV

Volume Setting

• Press “ ” button to decrease volume or

button to increase volume, so a volume level scale

(slider) will be displayed on the screen.

Programme Selection

• Press “ ” button to select the next programme or

“ ” button to select the previous programme.

Viewing Main Menu

• Press “ ” / “ ” buttons at the same time

to view main menu. In the Main menu select sub-

menu using “ ” or “ ” buttons and enter the

sub-menu using “ ” or “ ” buttons. To

learn the usage of the menus, refer to the menu

system sections.

AV Mode

• Press the “TV/AV” button in the control panel on the

TV to switch between AV modes.

Operation with the Remote Control

• The remote control of your TV is designed to control

all the functions of the model you selected. The

functions will be described in accordance with the

menu system of your TV.

• Functions of the menu system are described in the

following sections.

Volume Setting

• Press “ ” button to increase the volume. Press

“” button to decrease the volume. A volume

level scale (slider) will be displayed on the screen.

Programme Selection (Previous or Next

Programme)

• Press “ ” button to select the previous programme.

• Press “ ” button to select the next programme.

Programme Selection (Direct Access)

• Press numeric buttons on the remote control to select

programmes between 0 and 9. The TV will switch

to the selected programme. To select programmes

between 10-500 (for IDTV) or 10-199 (for analogue),

press the numeric buttons consecutively

• Press directly the programme number to reselect

single digit programmes

Initial Settings

When the TV is turned on for the fi rst time, the menu

for the language selection appears on the screen. The

message “Welcome please select your language!”

is displayed in all language options sequentially in

the OSD.

By pressing the “ ” or “ ” buttons highlight the

language you want to set and press OK button. After

then, “First time installation” OSD will appear on the

screen. By pressing “ ” or “ ” buttons, select the

country you want to set and press OK button (* for

EU countries).

Note: Country selection OSD will not be available for UK.

Press OK button on the remote control to continue

and the following message will be displayed on the

screen:

• To select the “Yes” or “No” option, highlight the item

by using “ ” or “ ” buttons and press the “OK”

button.

The IDTV will automatically tune to the UHF or VHF(*)

(* for EU countries) transmission channels, searching

for digital terrestrial TV broadcasts and displaying the

names of channels found. This process will take about

a few minutes.

After Automatic Search is completed, the following

message asking for analogue channel search appears

on the screen:

To search for analogue channels, select “Yes”. TV

switches to the analogue TV mode. The menu is

displayed to search for analogue channels.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 11A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 11 08.04.2010 08:52:5808.04.2010 08:52:58

English - 12 -

Select your Country, Language and Text language by

using “ ” or “ ” and “ ” or “ ” buttons. Press OK or

RED button to continue. To cancel, press the BLUE

button.

For more information on this process, see “Install Menu”

section.

Note: For proper functioning of digital teletext in DTV mode, you

should set country as UK in analogue AUTO PROGRAM (for UK

broadcasts only).

Do not turn off the TV while initializing fi rst time installation.

General Operation

Press the “TV/DTV” button on the remote control and

select DTV to switch the TV set to digital terrestrial

television broadcasting.

Information Banner

• Whenever you change the channel using the /

button or numeric buttons, the TV displays the

broadcast picture along with an information banner

at the bottom of the screen. This will remain on the

screen for approximately a few seconds.

• The information banner can also be displayed by

pressing the button at any time while watching

the TV. Pressing button again removes the

banner.

If the selected channel is locked, you must enter the

correct four numeric code to view the channel. “Enter

PIN” will be displayed on the screen in such a case:

Electronic Programme Guide (EPG)

• Some, but not all, channels send information about

the current and next events. Press GUIDE button to

view the EPG menu. EPG appears on the screen. It

is able to get Information of the channel - programs

weekly by means of 7-DAY-EPG. All programs of

channels are displayed. On the bottom of the screen;

info bar, showing all the available commands, will

be displayed.

RED button (Shrink): makes the info boxes smaller.

GREEN button (Expand): makes the info boxes larger.

YELLOW button (Prev. Day): displays the programmes

of previous day.

BLUE button (Next day): displays the programmes of

the next day.

(Details): displays the programmes in detail.

Numeric buttons (Jump): go to preferred channel

directly via numeric buttons.

OK : view for current broadcast/reminders for future

programs.

: jumps to the current broadcast.

• Press “0” button on the remote control to view Guide

Search menu. Using this feature, you can search the

programme guide database in accordance with the

genre selected or with name match.

Displaying Subtitles

With digital terrestrial broadcasting (DVB-T), some

programmes are being broadcasted with subtitles.

Press the “MENU” button to display the main menu,

highlight the Setup and then Language menu using “

” or “ ” button and press the OK button to display the

“Language settings” menu.

Highlight the “Subtitle” item in “Language settings”

menu and use ” or “ button to set Subtitle to the

desired language.

If “Subtitle” is on and a language option is set, pressing

the “ ” button causes the following warning message

display on the screen (** for UK only):

Digital Teletext (** for UK only)

• Press the “ ” button.

• The digital teletext information appears.

• Operate it with the coloured buttons, cursor buttons

and OK button.

The operation method may differ depending on the

contents of the digital teletext.

Follow the instructions displayed on digital teletext

screen.

• When Press “OK” button or similar message appears

on the screen, press the OK button.

• When the “ ” button is pressed, the TV returns to

television broadcasting.

• With digital terrestrial broadcasting (DVB-T), in

addition to digital teletext broadcasting together with

the normal broadcasting, there are also channels

with just digital teletext broadcasting.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 12A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 12 08.04.2010 08:52:5908.04.2010 08:52:59

English - 13 -

• The aspect ratio (picture shape) when watching

a channel with just digital teletext broadcasting is

the same as the aspect ratio of the picture viewed

previously.

• When you press the “ ” button again, the digital

teletext screen will be displayed.

Analogue Teletext

Use of teletext and its functions are identical to

the analogue text system. Please do refer to the

“TELETEXT” explanations.

Widescreen

Depending on the type of the broadcast being

transmitted, programmes can be viewed in a number

of formats. Press the “ZOOM” button repeatedly to

change screen format.

When Auto is selected, the format being displayed is

determined by the picture being broadcasted.

PLEASE NOTE: Menu size changes depending on the

chosen image size.

Notice !

If there is no audio available, the following warning

message will be displayed on the screen:.

IDTV Menu System

The IDTV menu can only be viewed when watching

digital terrestrial broadcasting. Press the “TV/DTV”

button to turn IDTV on while the TV is in analogue

mode. Press the “MENU” button. The menu below

appears on the screen:

You can press MENU button again to exit main

menu.

Channel List

Using the “ ” or “ ” button on the remote control, make

sure that the fi rst item, Channel List, is highlighted and

press the “OK” button to display the Channel List.

Navigating the Entire Channel List

Press “ ” or “ ” button for selecting the previous or next

channel. You can press “RED” or “GREEN” button to

move page up or page down.

To watch a specifi c channel, highlight it using “ ” or “

” button and then press “OK” button, while the “Select”

item on Channel List menu is highlighted by using “

” or “ ” button.

Then the name and number of the selected channel will

be displayed in the top-left and top-right of the channel

display at the top-right of the screen, respectively.

Moving the channels in the channel list

• Press “ ” or “ ” buttons to select the channel that

will be moved.

• Press “ ” or “ ” buttons to select the “Move” item on

Channel List menu.

Following OSD will be displayed next to “OK” item

to indicate that enter a number by using the numeric

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 13A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 13 08.04.2010 08:53:0008.04.2010 08:53:00

English - 14 -

buttons on the remote control and press “OK” to

confi rm.

Note: If you enter the same programme number of the channel

that you want to move, “.... channel services will be replaced.

Do you want to continue?” OSD will be displayed. Press OK

to confi rm or select “No” to cancel.

Deleting the Channels in the Channel List

• Press “ ” or “ ” button to select the channel that

will be deleted.

• Press “ ” or “ ” button to select the “Delete’’ item

on Channel List menu.

• Press the “OK” button to delete the highlighted

channel in the channel list. Then the message below

appears on the screen:

• Press “ ” or “ ” button to highlight the desired

option. If “OK” button is pressed while “Yes” is

highlighted, the highlighted channel is deleted.

Selecting “No” cancels the deletion.

Renaming Channels

To rename a specifi c channel, the channel must

be highlighted by pressing “ ” or “ ” button. Then

highlight the Edit Name item by pressing “ ” or “ ”

button as illustrated below. Press the “OK” button to

activate the rename feature.

Now pressing “ ” or “ ” button moves to the previous/

next character. Pressing “ ” or “ ” button toggles

the current character, i.e., ‘b’ character becomes ‘a’

by “ ” and ‘c’ by “ ”. Pressing the numeric buttons

‘0...9’ replaces the highlighted character with the

characters printed above the button one by one as

the button is pressed.

Press the “MENU” button to cancel the editing or OK

button to save the new name.

Adding Locks to Channels

Channel locking provides a password-protected

access to channels selected by parents. In order to

lock a channel you should know the parental lock

password (default value is set to 0000 in the factory

and can only be changed from the Confi guration

menu).

Select the channel to be locked by highlighting it and

select the Lock option by pressing “ ” or “ ” button.

When the “OK” button is pressed, a dialog OSD asking

for the password will be displayed.

Enter the password by using the numeric buttons on

the remote control. The lock icon “ ” will now be

displayed next to the selected channel. Repeat the

same operation to cancel the lock.

Setting Favourites

To set a favourite you should highlight the “Favourites”

item at the bottom of the Channel List menu. Then

press “OK” button and Edit Favourite List menu

appears on the screen.

How to Add a Channel to a Favourites List

• By pressing “ ” or “ ” buttons, highlight the channel

that you want to add to the favourite list.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 14A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 14 08.04.2010 08:53:0108.04.2010 08:53:01

English - 15 -

• By pressing “OK” button, the highlighted channel is

added to the Favourite List.

• F icon indicates that a channel is added to Favourite

List.

Removing a Channel from Favourite List

• Highlight the channel that you want to remove from

the favourite list and press OK button to remove.You

can press “OK” button again to re-add a channel.

• To activate Favourites, go to the Confi guration menu

and select Favourite mode. Use “ ” / “ ” to set

Favourite mode as on. To cancel Favourites, set

Favourite Mode to Off.

On Screen Help

For all menus, press the button to display the help

information about the menu functions.

Program Guide

This section is same with the instructions given in

the General Operations page. Please see Electronic

Programme Guide (EPG) section in the General

Operations part.

Timers

To display timers window, activate the item from the

main menu. To add a timer, press the YELLOW button

on the remote control. Then “Add Timer” window

appears.

Channel: “ ” or “ ” keys will navigate the user

through the TV or Radio list.

Date: Starting date is entered via the Left/Right or the

numeric buttons.

Start: Starting time is entered via the Left/Right or

the numeric buttons.

End: Ending time is entered via the Left/Right or the

numeric buttons.

Change/Delete: permits or prohibits any modifi cations

for other users.

Duration: Duration between Start and End time.

Repeat: You can set a timer to be repeated as Once,

Daily or Weekly.

You can save the adjustments by pressing the GREEN

key or cancel the process by pressing the RED button.

You can edit the list via GREEN key and delete with

the RED button.

Conditional Access

• Press the “MENU” button to display the main menu and

use the “ ” or “ ” button to highlight the “Conditional

Access” line and press the “OK” button:

Some Digital Terrestrial channels operate on a Pay

Per View basis. These require a subscription and a

hardware decoder.

Obtain the Conditional Access Module (CAM) and the

viewing card by subscribing to a pay channel company,

then insert those to the TV using the following procedure.

• Switch off the TV and unplug from the mains.

• The CAM should be correctly inserted, it is impossible

to insert fully if reversed. The CAM or the TV terminal

may be damaged if the CAM is forcefully inserted.

• Connect the TV to the mains supply, switch on and then

wait for few moments until the card is activated.

• Some CAMs may require the following set up. Please

set the CAM by entering the IDTV menu, Conditional

Access then pressing the “OK” button. (CAM set up

menu is not displayed when it is not required.)

• To see the viewing contract information: enter IDTV;

press the “MENU” button, then highlight Conditional

Access and press the “OK” button.

• When no module is inserted, “No Conditional Access

module detected” message appears on the screen.

• Refer to the module instruction manual for details of

the settings.

Note: Insert or remove the CI module only when the TV is

switched off or in standby mode.

TV Setup

You can use this item to display the TV functions.

The digital TV Setup menu screen is accessed from

the main menu. Press the “MENU” button to display

the main menu and use “ ” or “ ” button to highlight

“TV Setup”, press the “OK” button to display TV Setup

menu screen.

You can fi nd detailed information for all menu items in

“Analogue TV Menu System” section.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 15A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 15 08.04.2010 08:53:0208.04.2010 08:53:02

English - 16 -

Setup

The adjustments in this menu are given as the following:

Confi guration

You can confi gure the settings of your TV. Select

Confi guration from Setup menu and press “OK” to

view this menu. Press the “BACK” button on the

remote control to exit.

Dolby D Audio (* for EU countries only)

In the Configuration Menu, highlight the Dolby D item by

pressing “” or “ ” buttons. Use the “ ” or “ ” buttons

to set the Dolby D Digital as On or Off. If the channel that

you are watching supports Dolby Digital,you can turn this

setting on.

Hard of Hearing (* for EU countries only)

Use “ ” or “ ” button to select Hard of Hearing and

then press “ ” or “ ” button to set this setting as

On or Off.

If the broadcaster enables any special signal

concerning the audio, you can set this setting as On

to receive such signals.

Favourite Mode

Use this function to enable or disable favourite

mode. Press “ ” / “ ” button to set this function as

on or off.

Channel List

Use “ ” or “ ” buttons to go to Channel List option.

Use “ ” or “ ” buttons to toggle Channel List Mode.

If you select “TV Only”, with the “ ” or “ ” buttons,

you navigate through only TV channels. If you select

“Radio Only”, with the “ ” or “ ” buttons, you navigate

through only radio channels. If you select “Text Only”,

with the “ ” or “ ” buttons, you navigate through only

text channels.

Scan Encrypted

Scan Encrypted Channel feature will always be ON

after performing first time installation. When this

setting is on, search process will locate the encrypted

channels as well. If it is set as OFF manually, encrypted

channels will not be located while in automatic search

or manual search.

Use “ ” or “ ” button to select Scan Encrypted and

then press “ ” or “ ” button to set this setting as

On or Off.

Software Version

Over Air Download (OAD)

This feature helps to keep your TV updated. It works

This feature helps to keep your TV updated. It works

automatically and searches for new information

automatically and searches for new information

when available. Note that this setting is inactive to be

when available. Note that this setting is inactive to be

modifi ed

modifi ed

.

. Please ensure that the TV is set to standby

mode. The TV automatically powers up at 3.00 A.M.

each day and searches for any new information which

may be broadcasted and will download this to your

receiver automatically. This operation will normally

take approximately 30 minutes.

Note: Your TV may start in First Time Installation mode after

OAD update.

Parental Control

Use “ ” or “ ” buttons to go to Parental Lock option.

Press OK button to enter the menu. A dialog box

asking for the lock key will be displayed. The key is set

to “0000” initially. Enter PIN. If it is incorrect, “Wrong

Pin” OSD will be displayed. If it is correct, the Parental

Control menu will be displayed:

Maturity Lock (*)

(*) If you set Country option as UK in the fi rst time

installation, Maturity Lock option will not be visible.

This setting is available only for EU countries.

When set, this option gets the maturity information

from the broadcast and if this maturity level is disabled,

does not show video-audio.

Menu Lock

In menu lock you can set locking for all menus, or the

Installation Menu to restrict access to these menus.

If the menu lock is disabled, there will be free access

to the menu system. Use “ ” or “ ” buttons to go to

Menu Lock option. Use “ ” or “ ” buttons to choose

Menu Lock Mode.

DISABLED : All menus are unlocked.

ALL MENUS : All Menus are accessible only with

the correct lock key. So the user cannot add, delete,

rename, channels, cannot set timers.

INSTALLATION MENU: Installation menu is locked.

So the user can’t add channels. Changes will be

updated after exiting ‘Confi guration Menu’.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 16A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 16 08.04.2010 08:53:0308.04.2010 08:53:03

English - 17 -

Set PIN

Use “ ” or “ ” buttons to go to “Set PIN” option.

Press “OK” to display the “Set PIN” window. Use

numeric buttons to enter new pin number you will need

to input your new pin a second time for verifi cation

purposes.The factory default pin number is 0000, if

you change the pin number make sure you write it

down and keep it safe.

Time Settings (* for EU countries only)

In the configuration menu, highlight the Time Settings

item by pressing “ ” or “ ” buttons.

Press “OK” and Time Settings sub menu will be

displayed on the screen. Current Time,Time Zone

Setting and Time Zone will be available.

Use “ ” or “ ” buttons to highlight the Time Zone

Setting. Time Zone Setting is set using “ ” or “ ”

buttons. It can be set to AUTO or MANUAL.

When AUTO is selected, Current Time and Time Zone

options will not be available to be set. If MANUAL

option is selected as the Time Zone Setting, Time

Zone can be altered:

• By pressing “ ” or “ ” buttons select Time Zone.

Use “ ” or “ ” buttons to change the Time Zone

between GMT-12 or GMT+12. Current Time on the

top of the menu list will then change according to the

selected Time Zone.

Audio Description

Audio description refers to an additional narration

track for blind and visually impaired viewers of

visual media, including television and movies. The

description narrator talks through the presentation,

describing what is happening on the screen during the

natural pauses in the audio (and sometimes during

dialogue, if deemed necessary). You can use this

feature, only if the broadcaster supports that additional

narration track. Use “ ” or “ ” buttons to select an

item. Then use “ ” or “ ” buttons to set.

Audio Description

This function enables or disables the audio description

feature by pressing the “ ” or “ ” buttons.

Preferred Language

By pressing the “ ” or “ ” buttons the preferred audio

description language is being changed.

This setting can be used, only if it is available.

Relative Volume

Using this option, the Audio Description volume level

can be increased or decreased relatively, according

to the general volume.

Standby Search

Use “ ” or “ ” button to select Standby Search and

then press “ ” or “ ” button to set this setting as On or

Off. If you change Standby Search to Off, this function

will be unavailable.

To use Standby search please make sure that

you select Standby Search as On.

Language

In this menu the user can adjust the preferred

language. Language is changed by pressing “OK”

button.

Menu: shows the language of the system

Preferred

These settings will be used if available. Otherwise the

current settings will be used.

• Audio: by pressing “ ” or “ ” keys change the

audio language.

• Subtitle: alter the subtitle language with “ ” or “

” keys. The chosen language will be seen in

subtitles.

• Guide: By pressing “ ” or “ ” buttons change the

guide language.

Current

• Audio: if audio language is supported change the

audio language by pressing “ ” or “ ” buttons

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 17A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 17 08.04.2010 08:53:0508.04.2010 08:53:05

English - 18 -

• Subtitle: if subtitle is backed up, alter the subtitle

language with “ ” or “ ” buttons. The chosen

language will be seen in subtitles.

Note: If the Country option is set to Denmark, Sweden,

Norway or Finland, the Language Settings menu will function

as described below:

Language Settings

In the confi guration menu, highlight the Language

Settings item by pressing “ ” or “ ” buttons. Press

“OK” and Language Settings submenu will be

displayed on the screen:

Use “ ” or “ ” buttons to highlight the menu item

that will be adjusted and then press “ ” or “ ” button

to set.

Notes:

• System Language determines the on-screen menu

language.

• Audio Language is used for selecting the soundtrack

of a channels.

• Primary settings are the first priority when multiple

choices are available on a broadcast. Secondary

settings are the alternatives when the first options

are not available.

Installation

The Installation menu is mainly intended to help you

for creating a Channel Table in the most effi cient way.

Select Installation from the Confi guration menu by

pressing “ ” or “ ” buttons.

This menu includes the following items:

(*) For Denmark, Sweden, Norway or Finland.

Automatic Channel Scan

Automatic channel scan is started by pressing

“OK” button while Automatic channel scan item is

highlighted.

The following message appears on the screen:

Highlight Yes or No by using “ ” or “ ” buttons and

press “OK” button to confi rm.

If Yes is selected, automatic search starts.

Selecting No cancels automatic search.

After search is completed for digital channels, a

message asking whether to search for analogue

channels appears on the screen:

Press the “OK” button to search for analogue

channels. The following menu appears on the screen

for analogue channel search:

Select your Country, Language and Text language

by using “ ” or “ ” and “ ” or “ ” buttons. Press

“OK” or RED button to continue. To cancel, press

BLUE button. The following menu will be displayed

during the automatic tuning:

After APS is fi nalized, the programme table will appear

on the screen. In the programme table you will see

the programme numbers and names assigned to the

programmes.

Manual Channel Scan

In manual channel scan, the number of the multiplex is

entered manually and only that multiplex is searched

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 18A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 18 08.04.2010 08:53:0708.04.2010 08:53:07

English - 19 -

for the channels. For each valid channel number, signal

level and signal quality are shown on the screen.

In both manual and auto search any existing channel

in the database is not re-stored to avoid redundant

duplicates of that channel.

Clear Service List (*)

(*) This setting is visible only when the Country option

is set to Denmark, Sweden, Norway or Finland.

Use this setting to clear channels stored. Press “ ” or “ ”

button to select Clear Service List and then press OK. The

following OSD message will be displayed on the screen:

Press OK to cancel. Select Yes by pressing “ ” or “ ”

button and press OK to delete all of the channels.

First Time Installation

The user can use this item to load default settings,

which were loaded to the receiver at the factory.

To install factory settings, highlight “First Time

Installation” menu item and press “OK” button,

then you will be asked whether or not to delete the

settings. Selecting “Yes” by pressing “OK” button

while the “Yes” is highlighted will delete the existing

channel table.

Then you will be asked to confi rm for deleting all

channels and settings:

By selecting Yes and pressing the “OK” button, the

existing channel table will be deleted. After factory

settings are loaded, “First Time Installation” menu

will be displayed.

The menu which is displayed for language selection

appears on the screen at fi rst. By using “ ” or “ ”

buttons, select the desired language option, and press

OK button to activate.

After then, “First time installation” OSD will appear

on the screen. By pressing “ ” or “ ” buttons, select

the Country you want to set and press “OK” button

(* only for EU countries).

Press the “OK” button to start installation. After search

is completed for digital channels, a message asking

whether to search for analogue channels appears

on the screen.This process is same as described in

Automatic Search section..

Analogue TV Menu System

Picture Menu

Mode

For your viewing requirements, you can set the related

mode option.

Press “ ” or “ ” button to select Mode. Press “

” or “ ” button to choose from one of these options:

Cinema, Dynamic and Natural.

Brightness/Contrast/Colour/Sharpness/

Hue

Press “ ” or “ ” button to select the desired option.

Press “ ” or “ ” button to set the level.

Note: Hue option can only be visible when the TV receives

an NTSC signal.

Colour Temp

Press “ ” or “ ” button to select Colour Temp. Press

“” or “ ” to choose from one of these options: Cool,

Normal and Warm.

Note:

• Setting Cool option gives white colours a slight blue

stress.

• Setting Warm option gives white colours a slight red

stress.

• For normal colours, select Normal option.

Noise Reduction

If the broadcast signal is weak and the picture is

noisy, use Noise Reduction setting to reduce the

noise amount.

Press “ ” or “ ” button to select Noise Reduction.

Press “ ” or “ ” to choose from one of these options:

Low, Medium, High or Off.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 19A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 19 08.04.2010 08:53:0808.04.2010 08:53:08

English - 20 -

Game Mode

Select Game Mode by pressing “ ” or “ ” button.

Use “ ” or “ ” button to set Game Mode as On or

Off. When Game Mode is set to On, specifi c game

mode settings, which are optimized for better video

quality, will be loaded.

Also; Picture Mode, Contrast, Brightness, Sharpness,

Colour and Colour Temp settings will be invisible and

disabled while Game Mode is on.

Note:

Picture mode selection button on the remote control will have

no function while Game Mode is on.

Picture Zoom

Select Picture Zoom by pressing “ ” or “ ” button.

Use “ ” or “ ” buttons, to change picture zoom to

Auto, 16:9, 4:3, Panoramic, 14:9, Cinema, Subtitle

or Zoom.

Reset

Press “ ” or “ ” button to select Reset. Press

“” or “ ” or OK button to reset the picture modes to

factory default settings.

Sound Menu

Volume

Press “ ” or “ ” button to select Volume. Press “ ”

or “ ” button to change the level of the Volume.

Equalizer

Press “ ” or “ ” button to select Equalizer. Press “

” button to view equalizer menu.

Press “ ” or “ ” button to change the preset. In

equalizer menu, the preset can be changed to Music,

Movie, Speech, Flat, Classic and User.

Select the desired frequency by pressing “ ” or “ ”

button and increase or decrease the frequency gain

by pressing “ ” or “ ” button.

Press the “MENU” button to return to the previous

menu.

Note: Equalizer menu settings can be changed only when

the Equalizer Mode is in User.

Balance

This setting is used for emphasizing left or right

speaker balance.

Press “ ” or “ ” button to select Balance. Press “

” or “ ” button to change the level of the balance.

Balance level can be adjusted between -32 and +

32.

Headphone

Press “ ” or “ ” button to select Headphone. Press

“ ” button to view the headphone menu.

Headphone sub-menu options are described below:

Volume

Press “ ” or “ ” button to select Volume. Press “

” button to increase headphone volume level. Press

“” button to decrease headphone volume level.

Headphone volume level can be adjusted between

0 and 63.

Sound Mode

Press “ ” or “ ” button to select Sound Mode. Using

“” or “ ” button, you can select Mono, Stereo, Dual I

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 20A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 20 08.04.2010 08:53:1008.04.2010 08:53:10

English - 21 -

or Dual II mode, only if the selected channel supports

that mode.

AVL

Automatic Volume Limiting (AVL) function adjusts the

sound to obtain fi xed output level between programmes

(For instance, volume level of advertisements tend to

be louder than programmes).

Press “ ” or “ ” button to select AVL. Press “ ” or

“” button to set the AVL as On or Off.

Feature Menu

Sleep Timer

Press “ ” or “ ” button to select Sleep Timer. Use

“ ” or “ ” button to set the Sleep Timer.

The timer can be programmed between Off and 120

minutes in steps of 10 minutes.

If Sleep Timer is activated, at the end of the selected

time, the TV goes automatically to standby mode.

Child Lock

Press “ ” or “ ” button to select Child Lock.

Use “ ” or “ ” button to set the Child Lock On or Off.

When On is selected, the TV can only be controlled

by the remote control handset. In this case the control

panel buttons will not work.

Hence, if one of those buttons is pressed, Child Lock

On will be displayed on the screen when the menu

screen is not visible.

Language

Press “ ” or “ ” button to select Language. Use “

” or “ ” button to select the Language.

Default Zoom

While zoom mode is set as AUTO, the TV will set

the zoom mode in accordance with the signal of

the broadcast. If there is no WSS or aspect ratio

information, the TV will then use this setting to adopt.

Press “ ” or “ ” button to select Default Zoom. You

can set Default Zoom to Panoramic, 16:9, 4:3 or

14:9 by pressing “ ” or “ ” button.

Blue Background

If the signal is weak or absent, the TV will automatically

change to a blue screen. To enable this, set Blue

Background to On.

By pressing “ ” or “ ” button, select Blue

Background. Press “ ” or “ ” button to set Blue

Background as On or Off.

Menu Background

Press “ ” or “ ” button to select Menu Background.

You can set menu background level by pressing “

” or “ ” button.

Backlight

This setting controls the backlight level. Select

Backlight by pressing “ ” or “ ” button. Press“

” or “ ” button to set Backlight to Auto, Medium,

Maximum or Minimum.

Menu Timeout

To set a specifi c display timeout for menu screens,

set a value for this option.

Press “ ” or “ ” button to select Menu Timeout. Use

“” or “ ” button to change menu timeout to 15 sec,

30 sec or 60 sec.

Teletext Language

Press “ ” or “ ” button to select Teletext Language.

Use “ ” or “ ” button to change Teletext Language to

West, East, Turk/Gre, Cyrillic, Arabic or Persian.

HDMI PC Full Mode

If you want to view PC screen in HDMI mode by using

external connection, HDMI PC FULL MODE option

should be On to adjust the screen ratio correctly. This

item might be inactive in some resolutions.

Note: If you connect an HDMI device and switch the TV to

HDMI mode, this feature will be visible (for 720P and higher

resolutions).

Full Mode (*only for FHD models)

If you connect a device via HDMI or YPbPr connectors

and set 1080i/1080P resolutions, Full Mode item will

be visible.You can set Full Mode as 1:1 or Normal

by using “ ”or “ ”.If you select 1:1, screen ratio will

be adjusted correctly. If you set Normal, screen ratio

may expand.

Ext Out

Press “ ” or “ ” button to select Ext Out. Use “ ” or

“ ” button to set the Ext Out as On or Off.

Note:

For copying from a DVD or VCR device, you should choose

desired source from source menu and turn “On” to EXT Out

from feature menu.

Ext Out should be On in order to use Timers function in the

DTV mode.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 21A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 21 08.04.2010 08:53:1208.04.2010 08:53:12

English - 22 -

Install Menu

Program

Press “ ” or “ ” button to select Program. Use “ ”

or “ ” button to select the program number. You can

also enter a number using the numeric buttons on the

remote control. There are 200 programme storage

between 0 and 199.

Band

Band can be selected either C or S. Press “ ” or “

” button to set Band.

Channel

Channel can be changed by “ ” or “ ” button or

numeric buttons.

Colour System

Press “ ” or “ ” button to select Colour System. Use

“” or “ ” button to change the colour system to PAL,

PAL 60, SECAM or AUTO.

Sound System

Press “ ” or “ ” button to select Sound System.

Press “ ” or “ ” button to change the sound system

to BG,DK, I, L or L’.

Fine Tune

Press “ ” or “ ” button to select Fine Tune. Press “

” or “ ” button to adjust the tuning.

Search

Press “ ” or “ ” button to select Search. Use “ ”

or “ ” button to start programme searching. You can

also enter the desired frequency using the numeric

buttons while Search item is highlighted.

Install Menu in AV Modes

The following screen appears in the install menu when

the TV is in AV modes. Note that limited options will

be available. Switch to TV mode for viewing complete

version of the Install menu.

Colour System

Press “ ” or “ ” button to select Colour System. Use

“” or “ ” button to change the colour system to PAL,

SECAM, PAL60, AUTO, NTSC 4,43 or NTSC 3,58.

Program Table

Select Program Table by pressing “ ” or “ ” button.

Press “ ” to display Program Table:

By moving the cursor in four directions you can reach

20 programmes in the same page. You can scroll the

pages up or down by pressing the navigation buttons

to see all the programmes in TV mode (except for the

AV modes). By cursor action, programme selection is

done automatically.

Name

To change the name of a programme, select the

programme and press the RED button.

The fi rst letter of the selected name will be highlighted.

Press “ ” or “ ” button to change that letter and “ ”

or “ ” button to select the other letters. By pressing

the RED button, you can store the name.

Move

Select the programme which you want to move by

navigation buttons. Press the GREEN button. By

navigation buttons move the selected programme to

the decided programme space and press the GREEN

button again.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 22A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 22 08.04.2010 08:53:1508.04.2010 08:53:15

English - 23 -

Delete

To delete a programme, press the YELLOW button.

Pressing the YELLOW button again erases the

selected programme from the programme list, and

the following programmes shift one line up.

APS (Auto Programming System)

When you press the BLUE button for starting

automatic tuning, Auto Programming System menu

will appear on the screen:

Press “ ” or “ ” button to select your country. If you

want to exit from A.P.S. function, press the BLUE

button.

When you press OK or RED button for starting

automatic tuning, all stored programmes will be erased

and the TV will search for available channels. During

the search, the following OSD will be displayed:

Whenever you press the BLUE button, APS function

stops and Program Table appears on the screen.

If you wait until the end of APS, Program Table will be

displayed with the programmes found and located.

Source Menu

Press “ ” or “ ” button and select the sixth icon.

Then press “ ” or “OK” button. Source menu appears

on the screen:

In source menu, highlight a source by pressing “ ” or

“” button and switch to that mode by pressing “ ”

button. Source options are; TV, DTV, EXT-1, EXT-1 S,

FAV, HDMI-1, HDMI-2, YPbPr and PC-VGA.

Note: Once you have connected optional equipment systems

to your TV, you should select the required input to view

pictures from that source.

PC Mode Menu System

See “Connecting the LCD TV to a PC” section for

connecting a PC to the TV set.

For switching to PC source, press “AV” button on your

remote control and select PC input. You can also use

“Source” menu to switch to PC mode.

Note that PC mode menu settings are available only while

the TV is in PC source.

PC Position Menu

Select the first icon by pressing “ ” or

“” button. PC Position menu appears on the screen:

Autoposition

If you shift the picture horizontally or vertically to an

unwanted position, use this item to put the picture

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 23A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 23 08.04.2010 08:53:1708.04.2010 08:53:17

English - 24 -

into correct place automatically. This setting therefore

automatically optimizes the display.

Select Autoposition item by using “ ” or “ ” buttons.

Press “OK” or “ ”, “ ” button.

Warning: Please ensure auto adjustment is performed

with a full screen image to ensure best results.

H (Horizontal) Position

This item shifts the image horizontally to right hand

side or left hand side of the screen.

Select H Position item by using “ ” or “ ” button.

Use “ ” or “ ” button to adjust the value.

V (Vertical) Position

This item shifts the image vertically towards the top

or bottom of the screen.

Select V Position item by using “ ” or “ ” button.

Use “ ” or “ ” button to adjust the value.

Phase

Depending on the resolution and scan frequency that

you input to the TV set, you may see a hazy or noisy

picture on the screen. In such a case you can use this

item to get a clear picture by trial and error method.

Select Phase item by using “ ” or “ ” buttons. Use

“ ” or “ ” button to adjust the value.

Dot Clock

Dot Clock adjustments correct the interference

that appear as vertical banding in dot intensive

presentations like spreadsheets or paragraphs or

text in smaller fonts.

Select Dot Clock item by using “ ” or “ ” buttons.

Use “ ” or “ ” button to adjust the value.

PC Picture Menu

For adjusting PC picture items, do the following:

Press “ ” or “ ” button to select the second icon. PC

Picture menu appears on the screen.

Brightness, Contrast, Colour and Colour

Temperature settings in this menu are identical to

settings defi ned in TV picture menu under “Analogue

TV Menu System”.

Note: If you set Colour Temp as User, you can defi ne R, G,

B settings manually.

Sound, Feature and Source settings are identical to the

settings explained in Analog Tv menu system.

Displaying TV Information

Programme Number, Programme Name, Sound

Indicator and Zoom Mode information is displayed

on the screen when a new programme is entered or

“” button is pressed.

Muting Function

Press “ ” button to disable sound. Muting indicator

will be displayed in the upper side of the screen.

To cancel muting, there are two alternatives; the fi rst

one is pressing the “ ” button and the second one

is increasing the volume level.

Freezing Picture

You can freeze the picture on the screen by pressing

the “OK” button on the remote control. Press the

“OK” button to freeze picture. Press again to quit

freeze mode.

Note: This feature will not be available while in PC

mode or watched movie from DVI source .

Zoom Modes

You can change the aspect ratio (image size) of the TV

for viewing the picture in different zoom modes.

Press “ZOOM” button to directly change the zoom

mode.

Available zoom modes are listed below.

Note:

In YPbPr and HDMI modes, while in 720p-1080i resolutions,

only 16:9 mode is available.

Zoom mode cannot be changed while in PC mode.

Auto

When a WSS (Wide Screen Signalling) signal, which

shows the aspect ratio of the picture, is included in

the broadcast signal or the signal from an external

device, the TV automatically changes the ZOOM

mode according to the WSS signal.

• When the AUTO mode does not function correctly

due to poor WSS signal quality or when you want to

change the ZOOM mode, change to another ZOOM

mode manually.

16:9

This uniformly stretches the left and right sides of a

normal picture (4:3 aspect ratio) to fi ll the wide TV

screen

.

• For 16:9 aspect ratio pictures that have been

squeezed into a normal picture (4:3 aspect ratio),

use the 16:9 mode to restore the picture to its

original shape.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 24A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 24 08.04.2010 08:53:1808.04.2010 08:53:18

English - 25 -

4:3

Use to view a normal picture (4:3 aspect ratio) as this

is its original size

.

Panoramic

This stretches the left and right sides of a normal

picture (4:3 aspect ratio) to fi ll the screen, without

making the picture appear unnatural.The top and

bottom of the picture are slightly cut off.

14:9

This zooms up the wide picture (14:9 aspect ratio) to

the upper and lower limits of the screen.

Cinema

This zooms up the wide picture (16:9 aspect ratio) to

the full screen.

Subtitle

This zooms up the wide picture (16:9 aspect ratio)

with subtitles to the full screen.

Zoom

This option zooms to the picture.Note: You can shift

to screen up or down by pressing “ ” / “ ” buttons

while picture zoom is selected as panaromic, 14:9,

Cinema or Subtitle.

Teletext

Teletext system transmits information such as news,

sports and weather on your TV. Note that is the signal

degrades, for example in poor/adverse weather

conditions, some text errors may occur or the teletext

mode may be aborted.

Teletext function buttons are listed below:

“ ” Teletext On-Off / PAT Mode

Activates teletext mode when pressed once. Pressing

this button again will split the screen into two windows,

one displaying the teletext and the other displaying

the current channel. Pressing again will quit the

teletext mode.

“ ” Index

Selects the teletext index page.

“ ” Expand

Press once to enlarge top half of the page, press again

to enlarge the bottom half of the page. Press again to

revert back to normal size.

“ ” Reveal

Shows hidden information (e.g. solutions of games).

“ ” Hold

Holds a text page when convenient. Press again to

resume.

“ ” Subcode Pages / Time

Selects subcode pages if available when the teletext

is activated. When the teletext is not activated,

displays time info if the programme has teletext

transmission.

/ and numbers (0-9)

Press to select a page.

Note: Most TV stations use code 100 for their index pages.

Coloured Buttons

(RED/GREEN/YELLOW/BLUE)

Your TV supports both FASTEXT and TOP text

systems. When these systems are available, the

pages are divided into groups or topics.

When FASTEXT system is available, sections in a

teletext page will become colour-coded and can be

selected by pressing the coloured buttons. Press

a coloured button that corresponds to with your

needs.

The coloured writings will appear, showing you which

coloured buttons to use when TOP text transmission

is present. Pressing or commands will request

the next or previous page respec tively.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 25A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 25 08.04.2010 08:53:1908.04.2010 08:53:19

English - 26 -

Tips

Image Persistence

Please note that ghosting may occur while displaying

a persistent image. LCD TVs’ image persistence may

disappear after a short time. Try turning off the TV for

a while. To avoid this, do not leave the screen in still

picture for extended periods.

No Power

If your TV system has no power, please check the

main power cable and connection to the mains

socket outlet.

Poor Picture

Have you selected the correct TV system? Is your TV

set or house aerial located too close to a non-earthed

audio equipment or neon lights, etc.?

Mountains or high buildings can cause double pictures

or ghost images. Sometimes you can improve the

picture quality by changing the direction of the aerial.

Is the picture or teletext unrecognisable? Check if you

have entered the correct frequency. Please retune the

channels. The picture quality may degrade when two

peripherals are connected to the TV at the same time.

In such a case, disconnect one of the peripherals.

No Picture

Is the aerial connected properly? Are the plugs

connected tightly to the aerial socket? Is the aerial

cable damaged? Are suitable plugs used to connect

the aerial? If you are in doubt, consult your dealer.

No Picture means that your TV is not receiving a

transmission. Have you selected the correct button on

the remote control? Try once more. Also make sure

the correct input source has been selected.

Sound

You can not hear any sound. Did you perhaps interrupt

the sound, pressing the “ ” button?

Sound is coming from only one of the speakers. Is the

balance set to one extreme? See Sound Menu.

Remote Control

Your TV no longer responds to the remote control.

Perhaps the batteries are exhausted. If so you can still

use the local buttons at the bottom of the TV.

Input Sources

If you cannot select an input source, it is possible that

no device is connected.

Check the AV cables and connections if you have tried

to connect a device.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 26A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 26 08.04.2010 08:53:2108.04.2010 08:53:21

English - 27 -

Appendix A: PC Input Typical Display Modes

The display has a maximum resolution of 1600 X 1200. The following table is an illustration of some of the

typical video display modes.

Your TV may not support different resolutions. Supported resolution modes are listed below.

If you switch your PC to an unsupported mode, a warning OSD will appear on the screen.

Index

Resolution Frequency

Standard

Hor Ver Ver (Hz) Hor

(KHz)

1640 480 60 31.5 VESA

2640 480 72 37.9 VESA

3640 480 75 37.5 VESA

4800 600 56 35.2 VESA

5800 600 60 37.9 VESA

6800 600 70 43.8

7800 600 72 48.1 VESA

8800 600 75 46.9 VESA

9832 624 75 49.7 MAC

10 1024 768 60 48.4 VESA

11 1024 768 70 56.5 VESA

12 1024 768 72 57.7

13 1024 768 75 60.0

14 1152 864 70 64.2 VESA

15 1152 864 75 67.5 VESA

16 1152 870 75 68.9 MAC

17 1280 768 60 47.7 VESA

18 1360 768 60 47.7

19 1280 960 60 60.0 VESA

20 1280 1024 60 64.0 VESA

21 1280 1024 75 80.0 VESA

22 1600 1200 60 75.0 VESA

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 27A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 27 08.04.2010 08:53:2108.04.2010 08:53:21

English - 28 -

Appendix B: AV and HDMI Signal Compatibility (Input Signal

Types)

Source Supported Signals Available

EXT-1

(SCART)

PAL 50/60 O

NTSC 60 O

RGB 50 O

RGB 60 O

EXT-1 S

(S-VIDEO) PAL 50/60 O

FAV PAL 50/60 O

NTSC 60 O

YPbPr

480I 60Hz O

480P 60Hz O

576I 50Hz O

576P 50Hz O

720P 50Hz O

720P 60Hz O

1080I 50Hz O

1080I 60Hz O

1080P 50Hz O

1080P 60Hz O

HDMI1

HDMI2

480I 60Hz O

480P 60Hz O

576I 50Hz O

576P 50Hz O

720P 50Hz O

720P 60Hz O

1080I 50Hz O

1080I 60Hz O

1080P 24Hz O

1080P 50HZ O

1080P 60HZ O

(X: Not Available, O: Available)

Note: In some cases a signal on the LCD TV may not be displayed properly. The problem may be an

inconsistency with standards from the source equipment (DVD, Set-top box, etc.). If you do experience such

a problem please contact your dealer and also the manufacturer of the source equipment.

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 28A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 28 08.04.2010 08:53:2108.04.2010 08:53:21

English - 29 -

TV BROADCASTING PAL/SECAM B/G D/K K’ I/I’ L/L’

RECEIVING CHANNELS VHF (BAND I/III)

UHF (BAND U)

HYPERBAND

Digital

Reception

MHEG-5 ENGINE compliant with ISO/IEC 13522-5 UK engine Profi le 1

for UKObject carousel support compliant with ISO/IEC 135818-6 and UK DTT profi le

Frequency range: 474-850 MHz for UK models

170-862 MHz for EU models

Transmission standard: DVB-T. MPEG-2

Demodulation: COFDM with 2K/8K FFT mode

FEC: all DVB modes

Video: MP@ML, PAL, 4:3/16:9

Audio: MPEG Layer I&II 32/44.1/48kHz.

NUMBER OF PRESET CHANNELS 200 (Analog) / 500 (Digital)

CHANNEL INDICATOR On Screen Display

RF AERIAL INPUT 75 Ohm (unbalanced)

OPERATING VOLTAGE 220-240V AC, 50 Hz.

AUDIO German+Nicam Stereo

AUDIO OUTPUT POWER (WRMS.) (10% THD) 2 x 6

POWER CONSUMPTION (W) 150 W (max)

< 1 W (Standby)

PANEL 32” wide display

DIMENSIONS (mm)

W xHxD (with stand): 787 mm x 556 mm x 187 mm

Weight : 11.5 Kg (with stand)

W xHxD (without stand): 787 mm x 514 mm x 94 mm (TV only)

Weight : 10.5 Kg (TV only)

Specifi cations

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 29A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 29 08.04.2010 08:53:2208.04.2010 08:53:22

English - 30 -

Important Instruction

For your own safety read following instruction carefully before attempting to connect this unit to the mains

supply.

MAINS (AC) OPERATION

The wires in the mains lead are coloured in accordance with the following code :

IMPORTANT

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured

markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured green and yellow must be connected to the terminal which is marked with

the letter E, or by the earth symbol, or coloured green or green and yellow.

The wire which is coloured blue or black must be connected to the terminal which is marked with the

letter N or coloured Black.

The wire which is coloured brown or red must be connected to the terminal which is marked with the

letter L or coloured Red.

For continued protection against risk of fi re, replace only with same type and rating of fuse (ASTA

approved 5A 250VAC fuse).

CAUTION

TO PREVENT ELECTRIC SHOCK DISCONNECT FROM THE MAINS BEFORE REMOVING

COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

SAFETY PRECAUTION

THIS EQUIPMENT MUST BE DISCONNECTED FROM THE MAINS WHEN NOT IN USE. DO NOT

ALLOW THIS UNIT TO BE EXPOSED TO RAIN OR MOISTURE.

GREEN

&

YELLOW

(Earth)

(if there is earth cable)

FUSE

BROWN

(Live)

BLUE

(Neutral)

A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 30A01_[GB]_MB45M_32741W_(RM-C2503-1C_UK)_IDTV_NICKEL13_10067461_50164104.indd 30 08.04.2010 08:53:2208.04.2010 08:53:22

LT-32DG20J

©2010 Victor Company of Japan, Limited 0410TMH-VT-VT

50164104

INSTRUCTIONS

WIDE LCD PANEL TV

ENGLISH

If something doesn't seem to work

If there is something about your appliance which you do

not understand and you live in the UK you can

Phone our help line during normal office hours on:

0844 8009595

Calls are charged at standard rates.

We apologise for any inconvenience caused by minor

inconsistencies in these instructions, which may occur

as a result of product improvement and development.

Kesa U.K HU1 3AU 29 / 04 / 2008

䄰ㅟ孇䉝彍䈴㕍彃佖䕒弱〰㘷㐶ㅟ㔰ㄶ㐱〴

〶⁎楳慮′〱〠卡泽‱㘺㌴㨰