JVC UX G375B G377/375 User Manual LVT2110 001A

User Manual: JVC UX-G375B UX-G375B English,

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

ENGLISH

MICRO COMPONENT SYSTEM

UX-G375
—Consists of CA-UXG375 and SP-UXG375

INSTRUCTIONS

CAUTION: Proper Ventilation
To avoid risk of electric shock and fire,
and to prevent damage, locate the
apparatus as follows:
1. Front: No obstructions and open
spacing.
2. Sides/Top/Back: No obstructions
should be placed in the areas shown
by the dimensions on the right.
3. Bottom: Place on the level surface.
Maintain an adequate air path for
ventilation by placing on a stand
with a height of 10 cm or more.

Getting started

Front view

❍ Supplied Accessories

SP-UXG375

SP-UXG375

After unpacking, check to be sure that you have all
the following items.
• Remote control, RM-SUXG355R (× 1)
• Lithium coin battery CR2025 (× 1)
– The battery has been installed in the remote
control when shipped from the factory.
• FM antenna (× 1)
If anything is missing, consult your dealer
immediately.

CA-UXG375
Side view

❍ Prepare the Remote Control

When you use the remote control for the first time, pull out the insulation sheet.
To Replace the Battery in the Remote Control
Lithium coin battery
(product number: CR2025)

CA-UXG375

CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

Specifications
Thank you for purchasing a JVC product.

For turning off the demonstration display, see
“Canceling the display demonstration”.
LVT2110-001A[B]
1209NYMCRECDT

©2010 Victor Company of Japan, Limited

Precautions
Notes on the power cord
• When you are away on travel or otherwise for an
extended period of time, remove the plug from the wall
outlet.
• When unplugging the System from the wall outlet,
always pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System
or moving the System.
• Do not alter, twist or pull the power cord, or put
anything heavy on it, which may cause fire, electric
shock, or other accidents.
• If the cord is damaged, consult a dealer and have the
power cord replaced with a new one.

Notes on installation
• Select a place which is level, dry and neither too hot nor
too cold—between 5˚C and 35˚C.
• Do not install the System in a place subject to
vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires,
hairpins, coins, etc. into the System.
• Do not block the vents.

Amplifier section
OUTPUT POWER: 60 W (30 W + 30 W) at 6 Ω (10% THD)
Speakers/Impedance:
6 Ω – 16 Ω
Audio input
AUDIO IN:
500 mV/47 kΩ (at “LEVEL 1”)
250 mV/47 kΩ (at “LEVEL 2”)
125 mV/47 kΩ (at “LEVEL 3”)
Digital input:
USB MEMORY
Tuner section
FM tuning range:

NOTES:
• Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately.
• To prevent the battery from overheating, cracking, or starting a fire:
– Do not recharge, short, disassemble or heat the battery or dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal, state, and local regulations.

87.50 MHz - 108.00 MHz

CD player section
Dynamic range:
Signal-to-noise ratio:
Wow and flutter:

88 dB
85 dB
Immeasurable

USB section
USB specification:
Compatible with USB 2.0 Full Speed
Compatible device:
Mass storage class
Compatible file system:
FAT16, FAT32
Output power:
DC 5 V 500 mA

General
Power requirements:
Power consumption:
Dimensions (W x H x D):
Mass:
Speakers
Speaker units:
Impedance:
Dimensions (approx.):
Mass (approx.):

Connections

AC 230 V , 50 Hz
30 W (power on)
1.00 W or less (standby)
165 mm x 251 mm x 245 mm
1.9 kg

Do not connect the AC power cord until all other connections have been made.

NOTES:
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep
the antennas away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor
reception.
• Make sure both the speakers are connected correctly and firmly.
• When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.

10 cm cone x 1
6Ω
140 mm x 251 mm x 141 mm
(W/H/D)
1.3 kg each

To connect the speaker cords
To connect the FM antenna (supplied)
Extend it so that you can obtain the best
reception.

Specifications and appearance are subject to change
without prior notice.

Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries.

For better FM reception

FM antenna (supplied)

Outdoor FM antenna
(not supplied)

Disconnect the supplied FM antenna, and
connect to an outdoor FM antenna using
a 75 Ω wire with coaxial type connector
(IEC or DIN45325).

Red

There are no user-serviceable parts inside. If anything
goes wrong, unplug the power cord and consult your
dealer.

Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and
remove the plug from the wall outlet, then consult your
dealer. Using the System in this state may cause a fire or
electrical shock.
• Do not expose the System to direct sunlight or place it
near a heating device.

From right
speaker

Black

From left
speaker

To a wall outlet
Plug the AC power cord only after all connections are complete.

Sound and other adjustments
Maintenance

Troubleshooting

To get the best performance of the System, keep your discs and mechanism clean.

If you are having a problem with your System, check this list for a possible solution before calling for service.

Handling discs
• Remove the disc from its case by holding it at the edge
while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the
disc.
• Put the disc back in its case after use.
• Be careful not to scratch the surface of the disc when
placing it back in its case.
• Avoid exposure to direct sunlight, temperature
extremes, and moisture.
To clean the disc:
• Wipe the disc with a soft cloth in a straight line from
center to edge.

Cleaning the System
• Stains should be wiped off with a soft cloth. If the
System is heavily stained, wipe it with a cloth soaked in
water-diluted neutral detergent and wrung well, then
wipe clean with a dry cloth.
• Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about
the following:
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it hard.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as
insecticides to it.
– DO NOT allow any rubber or plastic to remain in
contact for a long time.

General
Power does not turn on.
Adjustments or settings are suddenly
canceled before you finish.
Operations are disabled.

Initial settings

\ Power plug is not inserted securely. Plug in securely.
\ There is a time limit. Repeat the procedure again.

\ The built-in microprocessor may malfunction due to external
electrical interference. Unplug the AC power cord and then plug it
back in.
Unable to operate the System from the
\ The path between the remote control and the remote sensor on
remote control.
the System is blocked.
\ The batteries are exhausted.
No sound is heard.
\ Speaker connections are incorrect or loose.
\ Headphones are connected.
Disc/USB Mass Storage Class Device Operations
The disc/USB mass storage class device does
\ The disc is placed upside down. Place the disc with the label side
not play.
up.
\ The disc is recorded with the “packet writing (UDF file system)”. It
cannot be played. Check the files you want to play back.
\ The USB mass storage class device is not connected properly.
MP3/WMA groups and tracks are not played
\ Playing order is determined when the groups and tracks were
back in order as you expect.
recorded. It depends on the writing application.
The disc/USB mass storage class device
\ The disc is scratched or dirty.
sound is discontinuous.
\ MP3/WMA files have not been properly copied into the USB mass
storage class device.
Sound from USB mass storage class device is
\ Static electricity may stop the sound. In this case, disconnect and
interrupted.
connect the USB mass storage class device again after turning off
the System.
The disc tray does not open or close.
\ The AC power cord is not plugged in.
\ Disc ejection is prohibited (see page 2).
Radio Operations
Hard to listen to broadcasts because of noise.
\ Antennas connections are incorrect or loose.
\ The FM antenna is not properly extended and positioned.
Daily Timer Operations
Daily Timer does not work.
\ The System has been turned on when the on-time comes. Timer
starts working only when the System is turned off.
\ There might have been a power failure, set the clock first, then the
time again.

Timers

Canceling the display demonstration

Setting the clock

Setting the Sleep Timer

Setting the Daily Timer

When the System is turned on and no operation is
done for about 2 minutes, the display demonstration
automatically starts.
To cancel the display demonstration temporarily, press
and hold DEMO while the System is turned on, until
“DEMO OFF” appears.

Set the built-in clock before using Daily timer or Sleep
Timer.
1. Press and hold CLOCK/TIMER.

Press repeatedly to specify the time (in minutes) as
follows:

Using Daily Timer, you can wake up with your favorite
music.
• You can store three Daily Timer settings.
• Tune into a station, place a CD, or connect a USB mass
storage class device to the System beforehand.

CLOCK/
TIMER

AUTO STBY
SLEEP

10

20

30 60 90 120
OFF 180 150

• The SLEEP indicator lights up.
• To check the remaining time until the System shuts
off, press once.

2. Press SET.
DEMO

SET

Turning Off the System Automatically
—AUTO STANDBY (only for CD/USB)
3. Adjust the hour, then the minute.
UP

or

DOWN

SET

Press and hold until the A.STBY indicator lights on the
display.

1. Press CLOCK/TIMER repeatedly to display the
desired Daily Timer number ( 1/ 2/ 3 lights
up), then press SET during DAILY 1, DAILY 2 or
DAILY 3 is displayed.
CLOCK/
TIMER

AUTO STBY

• To go back to the previous step, press CANCEL.
• If you have already adjusted the clock before,
perform steps 1 to 3.

Display settings
Dim the display
You can dim the display window and illumination
lamp.
While the System is turned on...
DIMMER

Change the display information

Sound adjustments
Drop the volume in a moment

SLEEP
SET

• The A.STBY indicator starts flashing after playback
stops. If no operation is done for about 3 minutes, the
System turns off.
• To cancel this function, press and hold again.

2. 1 Adjust the hour then the minute for on-time.
2 Adjust the hour then the minute for off-time.
3 Select the playback source—“CD”, “USB”,
“TUNER FM”.
4 Select the volume.
UP

FADE
MUTING

• To restore the volume, press again, or adjust the
volume level.

Emphasize the sound (Sound Turbo)
SOUND TURBO

or

DOWN

SET

• You can select the volume level –“VOLUME 0”
(VOL MIN) to “VOLUME 40” (VOL MAX) and
“VOLUME – –”. If you select “VOLUME – –”, the
volume is set to the last level when the System is
turned off.

3. Turn off the System (on standby).

DISPLAY

The display information changes as follows:
• FM: Frequency = (PS)* = (PTY)* = (RT)* = Clock
• CD: Current track elapsed time = Clock
• MP3/WMA: Current track elapsed time = ID3 tag
= Current group/track = Clock
* Only when Radio Data System is received.

JVC bears no responsibility for any loss of data in USB mass storage class device while using this System.

• The S.TURBO indicator lights up.
• To cancel this function, press again.

Reinforce the bass sound (Hyper Bass Sound)
HBS

• The BASS indicator lights up.
• When Sound Turbo function is activated (see
above), the BASS indicator goes off and HBS
button does not work.
• To cancel this function, press again.

Adjust the tone (Bass/Treble)
Press once for adjusting the bass level; twice for
treble level, then, press VOLUME +/–.
Adjustable range: –3 to +3.
BASS/TREBLE
VOLUME

• When the on-time comes, the System sets the
volume gradually to the preset level.
• After you have set the Daily Timer and turn off
(standby) the system, the STANDBY lamp will start
flashing. (While on standby, indicator will not be
displayed.)
• To exit from the timer setting, press CANCEL as
required.
• To correct a misentry during the process, press
CANCEL. You can return to the previous step.
To Turn Off the Daily Timer
Press CANCEL when “DAILY” is lit up.
NOTE:
The operations are explained using the remote control, unless mentioned otherwise. However, if the System has the
same or similar button names, they can also be used for the operations.

1
EN1_UX-G375_[B].indd 1

11/25/2009 4:19:37 PM

Playing Back a Disc/USB Mass Storage Class
Device
This System can play back...
– Audio CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA
files in ISO 9660 format.
– USB mass storage class device containing MP3/WMA files.
• When playing back an MP3 or WMA track, MP3 or WMA indicator lights up.

Loading a Disc (on the System only)
1. Press to open the disc tray.
3. Press to close the disc tray.

2.
NOTE:
When using an 8 cm disc,
place it on the inner circle of
the disc tray.

Function of each part

Listening to FM Broadcasts

Stop playback

Basic Tuner Operations
1.

While playback is stopped, total track number and total playing time (for
MP3/WMA files, group number and track number) appear.

2. Select a frequency
Press and hold for more than 2 seconds.

RESUME Play
Press RESUME to activate RESUME Play so that the RESUME indicator
lights up.
When you stop the playback by one of the following operations,
“RESUME” appears and this System stores the beginning of the stopped
track on the disc or USB mass storage class device.
– Pressing 7 once
– Changing the source
When you start playback again, playback starts from the beginning of
the stopped track.
To clear the memory, open the disc tray, disconnect the USB mass
storage class device or press 7 twice.
• When you clear the memory and start playback, playback starts from
the first track.
To deactivate RESUME Play, press RESUME again.

or

1 Turn on or off
the power
STANDBY lamp

2 Select a
source

Select the next tracks.

CD

Connecting a USB Mass Storage Class Device
You can connect a USB mass storage class device such as a USB flash
memory device, MP3 player, multimedia card reader, etc. to the System.
USB memory
(not supplied)

3 Adjust the

• The (mono) indicator lights up.
• Stereo effect will be lost.
• To restore the stereo effect, press again.

Select a group (MP3/WMA only)

PROGRAM

• Finish the following steps while the indication on the display is flashing.

DOWN

Select the next groups.

3. Press to select a preset number for the station you want to store.
UP

Select the previous groups.

or

Forward search

SET

Press and hold to fast-forward the track during playback.
To stop searching, release the button.

USB

Tune in to a preset station
UP

Press and hold to fast-reverse the track during playback.
To stop searching, release the button.
Press to fast-reverse the track during playback.
To stop searching, press 6.
NOTES:
• If no disc is inserted or no USB mass storage class device is connected,
“NO DISC” or “NO USB” appears on the main display.
• If MP3/WMA files are not recorded on the disc or in the USB mass storage
class device, “NO PLAY” or “NO DATA” appears on the main display.

Stereo mini plug cord
(not supplied)

2. Select a PTY code.
UP

or

DOWN

3. “SEARCH” appears and the System searches for 30 preset FM stations,
stops when it finds the one you have selected, and tunes in to that
station.
PTY

• To stop searching any time during search, press PTY.
• To continue searching after it stops on an unwanted station, press PTY
while the indications on the display are flashing.
NOTE:
If no program is found, “NO PTY” appears.

or

DOWN

1. Turn the volume to minimum.
Digital Audio Player

Programming the Playing Order—Program Play

Playing at Random—Random Play

1. During stops, press so that the PRGM (program) indicator lights up.

1. Press so that the RND (random) indicator lights up and random play

LAY
DISP

AT
REPE

PROG

VOLUME

OM
RAND

the power

RAM

AUDIO

IN

ER
DIMM

USB

DE
R MO
TUNE

CD

ME
RESU

2. Select a track number.
or

3. Press to program the selected track.

RANDOM

Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track, press 4.
• To exit from random play, press RANDOM so that the RND (random)
indicator disappears during playback.

SET

4. Repeat steps 2 and 3 to program other tracks you want.
• If you try to program a 33rd track, “PRG FULL” will appear.

5. The tracks are played back in the programmed order.
or

Prohibiting Disc Ejection (on the System only)
You can lock the disc tray so that no one can eject the loaded disc while the
System is on standby.

S

• To cancel the prohibition, repeat the same procedure.

1. Press repeatedly to specify the repeat mode as follows:
1:
:

Repeats the current (or specified) track.
Repeats all tracks in the current group
(MP3/WMA only).
ALL:
Repeats all tracks.
No indicator (Off ): Normal playback
or

BLE
/TRE
BASS

RM-

Playing Repeatedly—Repeat Play

REPEAT

HBS

ME
VOLU

L
TRO
CON
OTE
355R
REM
UXG

USB

Operations for Program Play (while program stop mode)
• To check the programmed contents, press SET repeatedly.
• To add tracks, repeat steps 2 and 3 above.
• To erase or exit the program, press 7.
– The stored program is not kept.

PTY

SOUB

Press these buttons for 2 seconds while the System is on standby.

USB

SET

• As the number increases, the sound becomes louder.

Learning More about This System

N

RBO
D TU

You can select one of three levels as follows:

source

DOW

STBY
AUTO
P
SLEE

NOTE:
DO NOT turn off (standby) the System with the volume set to an
extremely high level; otherwise, the sudden blast of sound can damage
your hearing, speakers and headphones when you turn on the System or
start playback.

TUNER

Press and hold for more than 2 seconds while “AUDIO IN” is selected as
the source.

E
FAD G
IN
MUT

SET

CK/
CLO ER
TIM

AUDIO IN

To Adjust the Audio Input Level
If the sound from the other equipment connected to the AUDIO IN jack is
too loud or too quiet, you can change the audio input level through the
AUDIO IN jack (without changing the volume level).

2 Select a

UP

EL
CANC

Using Headphones
Be sure to turn down the volume before connecting or putting on the
headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.

2. Press repeatedly to select “AUDIO IN”.

3. Start playing the connected equipment.
4. Adjust the volume.

ER

TUN

starts.

PROGRAM

Listening to Other Equipment

Headphones
(not supplied)

1 Turn on or off

CD

PTY

Reverse search

NOTES:
• Always set volume to the minimum level when connecting or
disconnecting the USB mass storage class device.
• When connecting with a USB cable, use the USB 2.0 cable whose length is
less than 1 m.
• You cannot connect a computer to the USB MEMORY terminal of the
System.
• Do not disconnect the USB mass storage class device while playing back a
file. It may cause malfunction of both this System and the device.
• Electrostatic shock at connecting a USB device may cause abnormal
playback of the device. In this case, disconnect the USB device then reset
this unit and the USB device.

2.

1. Press to enter the PTY code setting mode.

Press to select its preset number.

Press to fast-forward the track during playback.
To stop searching, press 6.

• Current track number and elapsed playing time appear.
• During playback, press again to pause.

CD

You can locate a particular kind of program from the preset stations by
specifying the PTY codes.

DOWN

4. Press to store the station.

Play back the USB mass storage class device

DISPLAY

Presetting Stations
1. Tune in to a station you want to preset.
2. Press to activate the preset number entry mode.

volume

UP

Changing the Radio Data System Information

Searching for Programs by PTY Codes (PTY Search)

You can preset 30 FM stations manually.
To go back to the beginning of the current or previous tracks.

NOTE:
If you want to know more about Radio Data System, visit .

Each time you press the button, the information changes as follows:

Change the FM reception mode (When an FM stereo
broadcast is hard to receive)
TUNER MODE

Select a track

• Current track number and elapsed playing time appear.
• During playback, press again to pause.

Radio Data System allows FM stations to send an additional signal along
with their regular program signals.
With the System, you can receive the following types of Radio Data System
signals.
PS (Program Service): Shows commonly known station names.
PTY (Program Type):
Shows types of broadcast programs.
RT (Radio Text):
Shows text messages the station sends.

Press to improve reception.
Remote sensor

Play back the disc

The System starts searching for stations and stops when a station of
sufficient signal strength is tuned in.
• If an FM program is broadcast in stereo, the (stereo) indicator lights up
(only when the reception is good).
• Press during searching to stop.
• Press repeatedly to change the frequency step by step.

Receiving FM Stations with Radio Data System

3 Adjust the
volume

Basic and Common Operations
• Pressing one of the source buttons also turns on the System and starts
playing back if the source is ready or connected.
Playing Back a Disc/USB Mass Storage Class Device
• This System cannot play “packet write” discs.
• For MP3/WMA playback...
– In this manual, “file” and “track” are interchangeably used for MP3/WMA
operations.
– MP3/WMA discs are required a longer readout time than regular CDs. (It
depends on the complexity of the group/file configuration.)
– Some MP3/WMA files cannot be played back and will be skipped. This
result from their recording processes and conditions.
– When making MP3/WMA discs, use ISO 9660 Level 1 or Level 2 for the disc
format.
– This System can play back MP3/WMA files with the extension code <.mp3>
or <.wma> (regardless of the letter case—upper/lower).
– It is recommended that you make each MP3/WMA file at a sampling rate
of 44.1 kHz and at bit rate of 128 kbps. This System cannot play back files
made at bit rate of less than 64 kbps.
– Playback order of MP3/WMA tracks may be different from the one you have
intended while recording. If a folder (group) does not include MP3/WMA
tracks, they are ignored.
– Some characters or symbols will not be shown correctly on the display.
The maximum character number shown on the display is 30 for ID3 tag.
– This System can recognize a total of 999 tracks and 255 groups. Those
exceeding the maximum number cannot be recognized.
• For the USB mass storage class device playback...
– When connecting a USB mass storage class device, also refer to its manual.
– Connect one USB mass storage class device directly to the System at a time.
Do not use a USB hub.
– This System is compatible with USB 2.0 Full Speed.
– You cannot play back a file larger than 2 GB.
– This System may not play back some USB mass storage class devices and
does not support DRM (Digital Rights Management).

– Coded or encrypted tracks in a special method cannot be played on the
System.
– This System cannot recognize a USB mass storage class device whose rating
exceeds 5 V/500 mA.
– When playing a file which has a large transfer rate, sounds may be dropped
during playback.
– Some USB mass storage class devices may not be recognized or may not
work properly.
– The compatible format is FAT16/FAT32.
– JVC bears no responsibility for any loss of data in the USB mass storage
class device while using this System.
• USB mass storage class device is charged through the USB MEMORY terminal
when the System is turn on. (Some USB mass storage class device may be
charged through the USB terminal only when “USB” is selected as the source.)
Listening to Other Equipment
• If the audio output on the other equipment is not stereo mini plug type, use
a plug adapter to convert the stereo mini plug to the corresponding plug of
the audio output.
Refer to the manuals supplied with the other equipment.
Setting the Clock and Using Timers
• You can set the clock and Daily Timer while the System is turned on. While
setting the clock or Daily Timer, the display is turning on.
• The clock may gain or lose 1 to 2 minutes per month. If this happens, readjust
the clock.
• When you unplug the AC power cord or if a power failure occurs, the clock
and the timer will be canceled. You need to set the clock first, then the timer
again.
Timer Priority:
• If you activate the Sleep Timer after Daily Timer starts playing the selected
source, Daily Timer is canceled.

2
EN2_UX-G375_[B].indd 2

11/25/2009 4:21:45 PM



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2009:11:25 16:22:38+09:00
Subject                         : LVT2110-001A
Modify Date                     : 2010:01:22 13:10:07+09:00
Producer                        : Acrobat Distiller 7.0 (Windows)
Creation Date                   : 2009:11:25 16:22:38+09:00
Mod Date                        : 2010:01:22 13:10:07+09:00
Author                          : JVC
Creator Tool                    : Adobe InDesign CS2 (4.0.5)
Metadata Date                   : 2010:01:22 13:10:07+09:00
Document ID                     : uuid:0a921fb6-7ff1-4283-98b7-e8d2e5abe0f9
Instance ID                     : uuid:ffd9b8ca-f49d-4d71-b428-5800ce4259bc
Format                          : application/pdf
Creator                         : JVC
Title                           : UX-G377/375
Description                     : LVT2110-001A
Page Count                      : 2

EXIF Metadata provided by EXIF.tools