JVC UX G37B G37/UX G38 User Manual GNT0080 001A

UX-G38B UX-G38B GNT0080-001A English,

User Manual: JVC UX-G37B UX-G37B English,

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

IMPORTANT for the U.K.

MICRO COMPONENT SYSTEM

UX-G37
—Consists of CA-UXG37 and SP-UXG38

UX-G38
—Consists of CA-UXG38 and SP-UXG38

Thank you for purchasing a JVC product.

INSTRUCTIONS
GNT0080-001A[B]
0107JSKMDWJEM

©2007 Victor Company of Japan, Limited

Warnings, Cautions and Others
Caution —
button!
Disconnect the mains plug to shut the power off completely
(the STANDBY lamp goes off ). When installing the apparatus,
ensure that the plug is easily accessible. The
button in
any position does not disconnect the mains line.
• When the system is on standby, the STANDBY lamp lights
red.
• When the system is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
CAUTION:
• Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws governing the
disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.

CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of
10 cm or more.
Front view
Side view

DO NOT cut off the mains plug from this equipment. If
the plug fitted is not suitable for the power points in your
home or the cable is too short to reach a power point,
then obtain an appropriate safety approved extension lead
or consult your dealer.
BE SURE to replace the fuse only with an identical
approved type, as originally fitted.
If nonetheless the mains plug is cut off ensure to remove
the fuse and dispose of the plug immediately, to avoid a
possible shock hazard by inadvertent connection to the
mains supply.
If this product is not supplied fitted with a mains plug then
follow the instructions given below:

Basic and Common Operations
Operating on the System
To
Turn on or off (standby)
the power
Changing the display
brightness

Press
The STANDBY lamp on the System turns off/on.

Set the Save mode
Emphasize the sound
(Sound Turbo function)

IMPORTANT:
DO NOT make any connection to the terminal which is
marked with the letter E or by the safety earth symbol or
coloured green or green-and-yellow.
The wires in the mains lead on this product are coloured in
accordance with the following code:
Blue:
Neutral
Brown:
Live
As these colours may not correspond with the coloured
markings identifying the terminals in your plug proceed
as follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or coloured
black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or coloured
red.
IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.

STANDBY lamp

Press when the System is turned on.
To cancel this function, press again.
Press and hold for more than 2 seconds when the System is on standby.
• Setting the Save mode allows you to reduce power consumption by
turning the display off while on standby.
To cancel this function, press and hold for more than 2 seconds again.

Point at the remote
sensor on the front panel.
(The operating range is
approx. 7 m.)

To cancel this function, press again.

See “Playing Back a Disc/USB Mass Storage Class Device” on page 4.

CAUTION:
Excessive sound pressure from earphones or headphones
can cause hearing loss.

Select a source*
See “Listening to FM and AM Broadcasts” on page 5.

Information for Users on Disposal of Old Equipment
[European Union only]
This symbol indicates that the product with this symbol should not be disposed as general household
waste. If you want to dispose of this equipment, please do not use the ordinary dust bin! There is a separate
collection System for these products.

Notes on the power cord
• When you are away on travel or otherwise for an extended period of time, remove the plug from the wall outlet. A small
amount of power (3.0 W) is always consumed while the power cord is connected to the wall outlet.
• When unplugging the System from the wall outlet, always pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or moving the System.
• Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power cord replaced with a new one.
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and remove the plug from the wall outlet, then consult your dealer. Using
the System in this state may cause a fire or electrical shock.
• Do not expose the System to direct sunlight or place it near a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot nor too cold between 5˚C and 35˚C.
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the System.
• Do not block the vents.

Dear Customer,
This apparatus is in conformance with the valid European
directives and standards regarding electromagnetic
compatibility and electrical safety.
European representative of Victor Company of Japan,
Limited is:
JVC Technology Centre Europe GmbH
Postfach 10 05 52
61145 Friedberg
Germany

You can adjust the volume level from level 0 (“VOL MIN”) to level 31
(“VOL MAX”).

Adjust the volume

Operating on the Remote Control

Precautions

IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user
serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.

See “Listening to Digital Audio Player” on page 6.

There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult
your dealer.

To
Turn on or off
(standby) the power

To

Press
The STANDBY lamp on the System turns
off/on.
See “Playing Back a Disc/USB Mass Storage
Class Device” on page 4.

Select a source*

Press repeatedly to select “FM,” “AM,” or “LINE.”
• For “FM/AM,” see “Listening to FM and AM
Broadcasts” on page 5.
• For “LINE,” see “Listening to Digital Audio
Player” on page 6.
You can adjust the volume level from level 0
(“VOL MIN”) to level 31 (“VOL MAX”).

Adjust the volume

PHONES jack
The illustration of the unit
above is UX-G38.
• UX-G37 is in black color.
Press
• Once: for the bass level
• Twice: for the treble level
Then, press VOLUME + to increase the level or
press VOLUME – to decrease it.
• You can adjust the bass and/or treble level
from –3 to +3.

Adjust the tone (Bass/
Treble)

Press briefly (not applicable for FM mode).
For setting the clock, see “Setting the Clock
and Daily Timer” on page 6.
Press repeatedly to specify the time (in
minutes) as follows (The SLEEP indicator lights
on the display):

Changing the display
information (Clock
and Source)

Turn off the System by
using the sleep timer

Canceled
• To check the remaining time to turn off after
setting the sleep timer, press once.

To restore the volume, press again, or adjust
the volume level.

Drop the volume in a
moment
Emphasize the sound
(Sound Turbo
function)
Reinforce the bass
sound (Active Hyper
Bass Pro function)

The S.TURBO indicator lights on the display.
To cancel this function, press again.

* The corresponding source indicator lights on the display (except when selecting
“LINE”).

Press and hold until the AHB indicator lights
on the display.
• When Sound Turbo function is activated (see
above), this function cannot be activated.
To cancel this function, press and hold again.

NOTE
DO NOT turn off (standby) the System with the volume set to an extremely high level;
otherwise, the sudden blast of sound can damage your hearing, speakers and/or
headphones when you turn on the System or start playback.

Connections

Attaching the Core Filter
Attach the provided core filter to the power cord, then the
core filter reduces interference.

1

Do not connect the AC power cord until all other connections have been made.
NOTES
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the
antennas away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception.
• If the cords are covered with vinyl, remove the vinyl to expose the tip of the cord by twisting the vinyl.

Release the stopper of the core
filter.

This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/
WMA files in ISO 9660 format.
– USB mass storage class device which contains MP3/WMA files.
• When playing back an MP3 or WMA track, MP3 or WMA indicator lights
on the display.

Loading a Disc

Stopper

2

Prepare the Remote Control

3

Run the power cord through the
core filter, leaving approx. 5 cm
between the rear of the unit and
the core filter.
Wind firmly the power cord twice
inside the cutout of the core filter
as shown in the illustration.

1
To connect the AM loop antenna

FM antenna (supplied)
Extend it so that you can obtain the best reception.

Close the core filter until you hear
a clicking sound.

AM loop antenna (supplied)
Turn it until the best reception
is obtained.

Press to open the disc tray.

or

• When using an 8 cm disc, place it on
the inner circle of the disc tray.

2

Main Display

Basic Disc/USB Mass Storage Class Device Operations

Radio Data System indicators (See page 5.)
A.STBY (Auto Standby) indicator (See page 4.)
SLEEP indicator (See the left table.)
Timer mode indicators (See page 6.)

3

To

On the
System

On the
remote
• Current track number and elapsed playing time appear on the
main display.
For MP3/WMA files: Before current track number and elapsed
playing time appear, the tag information is scrolled if it is recorded.
• During playback, press again to pause.
• While playback is stopped, total track number and total playing
time (for MP3/WMA files, group number and track number)
appear on the main display.

Play back the disc
Play back the USB
mass storage
class device
Stop playback

To a wall outlet
Plug the AC power cord only after all
connections are complete.
For better FM reception

NOTES
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in
touch with the metallic parts of the System.

Outdoor FM antenna
(not supplied)

Disconnect the supplied FM antenna,
and connect to an outdoor FM antenna
using a 75 Ω wire with coaxial type
connector (IEC or DIN45325).

Select a group
(MP3/WMA only)
Forward search/
Reverse search

Front view

NOTES
• When connecting with a USB cable, use the cable whose length is less
than 1 m.
• USB mass storage class device is charged through the USB MEMORY
terminal when the System is turned on and the source is “USB.”
• You cannot connect a computer to the USB MEMORY terminal of the
System.
• Do not disconnect the USB mass storage class device when the System is
turned on. It may cause malfunction of both this System and the device.
• Noise and static electricity may stop the USB mass storage class device
sound. In this case, disconnect and connect the USB mass storage class
device again after turning off the System.

Turning Off the System Automatically
—AUTO STANDBY function
Press and hold until the A.STBY indicator lights on the display.
• The A.STBY indicator starts flashing after playback stops.
If no operation is done for about 3 minutes, the System
turns off.
To cancel this function, press and hold again.

Press to select the next groups while playback is stopped.

—

Press to select the previous groups while playback is stopped.
Press once or twice to fast-forward the track during playback.
To stop searching, press 6.
Press once or twice to fast-reverse the track during playback.
To stop searching, press 6.

—
—

RESUME Play
When you stop the playback by one of the following
operations, this System stores the beginning of the
stopped track on the disc or stores the stopped
position of the file on the USB mass storage class
device.
– Pressing 7 once (The RESUME indicator lights on the
display.)
– Changing the source
– Turning off the System
When you start playback again, playback starts from
the stored position.
To clear the stored position, press 7 while playback
is stopped.

• Opening the disc tray or disconnecting the USB
mass storage class device also clears the stored
position.
• When you clear the stored position and start
playback, playback starts...
– For disc: From the beginning of the first track
– For USB mass storage class device: From the
beginning of the current file
If you disconnect the USB mass storage class
device, connect it again, and start playback,
playback starts from the beginning of the first file.
NOTE
This function does not work in program play and
random play (see the right tables).

Playing Repeatedly—Repeat Play
Press repeatedly before you start playback to specify the repeat mode
as follows:
REP 1
Repeats the current (or specified) track.
Repeats all tracks in the current group (MP3/
REP GRP
WMA only).
ALL REP ALL Repeats all tracks.
REP OFF Normal playback

1

You can lock the disc tray so that no one can eject the loaded disc.
• This is possible while the System is on standby.

To cancel the prohibition, repeat the
same procedure.

—

NOTES
• If no disc is inserted, “NO DISC” appears on the main display.
• If no USB mass storage class device is connected, “NO USB” appears on the main display.
• If MP3/WMA files are not recorded on the disc or in the USB mass storage class device, “NO FILE” appears on the
main display.

Prohibiting Disc Ejection
On the System only
Press and hold

2

3
4

or

Select a track number to program.

Press to program the selected
track.
Repeat steps 2 and 3 to program other tracks you want.
• If you try to program a 33rd track, “FULL” will appear on
the main display.

5

USB cable (not supplied)

To connect the speaker cords
Make sure the both speakers are connected correctly and
firmly.
• Before connecting the speaker cords, twist and pull the
insulation coat off and remove.
When connecting the speaker cords, match the polarity of
the speaker terminals: gray cord to (+) and gray cord with
black stripe to (–).

2

The tracks are played back in the
programmed order.

or

To Operate on the Program Play Mode

You can connect a USB mass storage class device such as a USB flash
memory device, MP3 player, multimedia card reader, etc. to the System.
To assemble the
AM loop antenna

Press repeatedly until the PRGM
(program) indicator lights on the
display before playback.

1

Press to go back to the beginning of the current or previous tracks.

Press to close the disc tray.

or

Programming the Playing Order—
Program Play (not Applicable for MP3/
WMA Discs)

Press

Select a track

Connecting a USB Mass Storage Class Device

NOTE
Do not damage the power cord by applying excessive
power when winding.

Lithium coin battery
(product number: CR2025)

NOTES
• Store the battery in a place where children cannot reach. If
a child accidentally swallows the battery, consult a doctor
immediately.
• Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire. Doing any of these things may cause
the battery to give off heat, crack, or start a fire.
• Do not leave the battery with other metallic materials.
Doing this may cause the battery to give off heat, crack, or
start a fire.
• When throwing away or saving the battery, wrap it in tape
and insulate; otherwise, the battery may start to give off
heat, crack, or start a fire.
• Do not poke the battery with tweezers or similar tools.
Doing this may cause the battery to give off heat, crack, or
start a fire.
• Dispose of battery in the proper manner, according to
federal, state, and local regulations.
• The batteries (battery pack or batteries installed ) shall not
be exposed to excessive heat source such as sunshine, fire
or the like.
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.

QPL indicator
(See page 6.)

Press to select the next tracks.

To Replace the Battery in the Remote Control
Insert the battery into the remote control by matching the
polarity (+ and –) correctly.

Source indicators (See the left table.)
AHB indicator (See the left table.)
S.TURBO (Sound Turbo) indicator (See the left table.)
RESUME indicator (See page 4.)
FM reception
File type indicators (See page 4.)
indicators
Source indicators (See the left table.)
(See page 5.)

Playing Back a Disc/USB Mass Storage Class Device

Supplied Accessories

Insulation sheet

Display Information

3

Getting Started

When you use the remote control for
the first time, pull out the insulation
sheet.

Using Headphones
Be sure to turn down the volume before connecting or putting on
the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.

Play mode indicators
(See page 4.)

1

After unpacking, check to be sure that you have all the
following items. The number in parentheses indicates the
quantity of each piece supplied.
• Remote control (x 1)
• Lithium coin battery CR2025 (x 1) (The battery has been
installed when shipped from the factory.)
• AM loop antenna (x 1)
• FM antenna (x 1)
• Core filter (x 1)
If anything is missing, consult your dealer immediately.

Stereo mini plug cord

2

or

4

To

Press

Check the
programmed
contents

or

Press while playback is
stopped.

Repeat steps 2 and 3 above while playback
is stopped.
1 Press UP or DOWN to select the track you
want to erase while playback is stopped.

Add tracks
Erase tracks

2

Erase the
entire program
Exit from
program play

Press to erase the track.
Press while playback is
stopped.
Press twice while playback is
stopped.
• The stored program is
erased.

Playing at Random—Random Play

1
2

or

Press repeatedly until the RND
(random) indicator lights on the
display before you start playback.
Playback starts in random order.
Random Play ends when all
tracks are played back.

To Operate on the Random Play Mode
To
Skip a track
Go back to the
beginning of
the current
track
Exit from
random play

Press
Press to skip the current track.

Press to go back to the
beginning of the current track.
Press once while playback is
stopped.

Listening to FM and AM Broadcasts

Learning More about This System

Basic Tuner Operations

Receiving FM Stations with Radio Data System
Radio Data System allows FM stations to send an additional signal along with their regular program signals.
With the System, you can receive the following types of Radio Data System signals.
PS (Program Service):
Shows commonly known station names.
PTY (Program Type):
Shows types of broadcast programs.
RT (Radio Text):
Shows text messages the station sends.
Enhanced Other Networks: Provides the information about the types of the programs broadcast by the Radio Data System
stations of the different networks.
NOTE
If you want to know more about Radio Data System, visit .

Press

To

On the System

On the remote
Press repeatedly to select “FM” or “AM.”
• The selected frequency appear on the
main display.
Press and hold for more than 2 seconds.
The System starts searching for stations and
stops when a station of sufficient signal
strength is tuned in.
• If an FM program is broadcast in stereo, the
ST (stereo) indicator lights on the display
(only when the reception is good).
• Press during searching to stop.
• Press repeatedly to change the frequency
step by step.

Select FM or AM

Select a frequency

or

Tune in to a preset station

Change the FM reception mode
(When an FM stereo broadcast
is hard to receive or noisy)

—

or

Changing the Radio Data System
Information
Each time you press the button, the main display
changes as follows:

Press to select a preset number for the
station you store.
• For presetting stations, see below.

or

Frequency
(Non-Radio Data System signal)

NOTES
• If the System takes time to show the Radio Data System
information—PS, PTY, RT signals, “PS,” “PTY,” or “RT” will appear
while searching.
• If no Radio Data System signals are sent by a station, “NO PS,”
“NO PTY,” or “NO RT” appears on the main display.

Press to improve reception.
The MONO indicator lights on the display.
Reception will improve though the stereo
effect is lost.
To restore the stereo effect, press again.

—

Searching for Programs by PTY Codes
(PTY Search)

You can preset 30 FM and 15 AM stations manually.
Tune in to a station you want to preset.
• You can also store the monaural reception mode for FM preset stations if selected.
Press to activate the preset number entry mode.
• Finish the following steps while the indication on the display is flashing.
or

You can locate a particular kind of program from the preset
stations (see the left column) by specifying the PTY codes.
Press to enter the PTY code setting
mode.
“PTY” and “SELECT” appear alternately on
the main display.

1

Press to select a preset number for the station you store.

2

4

The Enhanced Other Networks function allows the System
to switch temporarily to a preset FM station broadcasting a
program of your choice (TA, NEWS, or INFO).
• This function works while listening to an FM station
providing the required signals.
Press repeatedly to select the program type as
follows:

TA
NEWS
INFO

Presetting Stations

1
2
3

Switching Temporarily to a Program
of Your Choice Automatically

or

Press to store the station.

How the Enhanced Other Networks function actually
works:
When a station starts broadcasting the program of your
choice, the System automatically switches to the station.
The program type indicator starts flashing.
After the program is over, the System goes back to the
previously tuned station, but the function still remains
active (the indicator stops flashing and remains lit).

Select a PTY code.
The System searches 30 preset FM
stations, stops when it finds the one
you have selected, and tunes in to that
station.

3

NOTE
When you unplug the AC power cord or if a power failure occurs, the preset stations will be
erased in a few hours.

Traffic announcement in your area.
News
Program the purpose of which is
impart advice in the widest sense.

NOTES
• To stop searching any time during search, press PTY SEARCH.
• To continue searching after it stops on an unwanted station,
press PTY SEARCH while the indications on the display are
flashing.
• If no program is found, “NOTFOUND” appears on the main
display.

Basic and Common Operations (see page 3)
• Pressing one of the source buttons also turns on the System
and starts playing back.
Playing Back a Disc/USB Mass Storage Class Device
(see page 4)
• This System cannot play “packet write” discs.
• For MP3/WMA playback...
– In this manual, “file” and “track” are interchangeably used
for MP3/WMA operations.
– This System can show the Tag data (Version 1).
– MP3/WMA discs are required a longer readout time than
regular CDs. (It depends on the complexity of the group/
file configuration.)
– Some MP3/WMA files cannot be played back and will be
skipped. This result from their recording processes and
conditions.
– When making MP3/WMA discs, use ISO 9660 Level 1 or
Level 2 for the disc format.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of the
letter case—upper/lower).
– It is recommended that you make each MP3/WMA file at a
sampling rate of 44.1 kHz and at bit rate of 128 kbps. This
System cannot play back files made at bit rate of less than
64 kbps.
– Playback order of MP3/WMA tracks may be different from
the one you have intended while recording. If a folder
does not include MP3/WMA tracks, they are ignored.
• For the USB mass storage class device playback...
– When connecting a USB mass storage class device, also
refer to its manual.
– Connect one USB mass storage class device to the System
at a time. Do not use a USB hub.
– This System is compatible with USB 2.0 Full Speed.
– You can play back MP3/WMA files in a USB mass storage
class device (maximum data transfer rate: 2 Mbps).
– You cannot play back a file larger than 2 Gigabyte.
– This System cannot recognize a USB mass storage class
device whose rating is other than 5 V and does not exceed
500 mA.
– This System may not play back some USB mass storage
class devices and does not support DRM (Digital Rights
Management).
• This System can recognize up to 511 tracks in a disc/USB
mass storage class device. Also, the System can recognize
up to 150 tracks per group and up to 99 groups in a disc/
USB mass storage class device (for MP3/WMA).
– Playable files which do not belong to any groups are
handled as Group 1.

Troubleshooting

IMPORTANT:
It should be noted that it may be unlawful to rerecord pre-recorded tapes, records, or discs without
the consent of the owner of copyright in the sound
or video recording, broadcast or cable program and
in any literary, dramatic, musical, or artistic work
embodied therein.

To Play Back Digital Audio Player Easily

Setting the Clock

1

• If you have already adjusted the clock before, press the button repeatedly
until the clock setting mode is selected.

2

When QP Link is activated, connecting a Digital Audio Player to
the LINE IN jack and starting playback performs the following:
– While listening to another source...
Changes the source to “LINE” automatically.
– While the System is on standby...
Turns on the System and changes the source to “LINE”
automatically (not applicable when the display is turned
off ).
NOTE
See “Learning More about This System” on page 7.

• To exit from the clock setting, press CLOCK/TIMER as required.
• To go back to the previous step, press CANCEL.

Setting the Daily Timer
Using Daily Timer, you can wake up with your favorite music.
• You can store three Daily Timer settings; however, you can activate only one of Daily Timers.
Press repeatedly to select one of the timer setting modes you want to set—DAILY 1 ON time, DAILY 2 ON
time, or DAILY 3 ON time—as follows:

1

Digital Audio Player
equipped with the
audio input

Listening to Digital Audio Player

1
2
3
4

Turn the volume to minimum.

Press repeatedly to select “LINE.”
Start playing the Digital Audio Player connected.
Adjust the volume level to the level you want to
listen to.

To Adjust the Audio Input Level
If the sound from the Digital Audio Player connected to the
LINE IN jack is too loud or too quiet, you can change the
audio input level through the LINE IN jack (without changing
the volume level).
Press and hold for more than 2 seconds while
“LINE” is selected as the source.
You can select one of three levels as follows:

ON (Time)

DAILY 2 Timer

ON (Time)

DAILY 3 Timer

ON (Time)
Clock setting mode

To audio input

1
2

2

Stereo mini plug
cord (not supplied)

Front view

Stereo mini plug cord (not supplied)

DAILY 1 Timer

Canceled

Digital Audio Player

Front view

Adjust the hour, then the minute.

or

Recording on Digital Audio Player

To audio output (or
headphone out, etc.)

Maintenance

Without setting the built-in clock, you cannot use Daily Timer and Sleep Timer.
• “0:00” flashes on the main display until you set the clock.
Press to activate the clock setting mode.

Press and hold for more than 2 seconds to
activate QP Link.
The QPL indicator lights on the display.
To cancel this function, press and hold for more
than 2 seconds again.

or

Start recording or standby recording on the Digital
Audio Player.
,

,or

Start playing the disc or USB mass storage class
device, or tune in to the station you want to
recording.

3

NOTES
• Before recording on a Digital Audio Player, deactivate QP
Link or do not connect the Digital Audio Player to the LINE
IN jack; otherwise, “LINE” will be selected as the source and
the recording will stop.
• Sound adjustments (see page 3) do not affect recording on
the Digital Audio Player.

Power does not come on.
\ Power plug is not inserted securely. Plug in securely.
Adjustments or settings are suddenly canceled before you
finish.
\ There is a time limit. Repeat the procedure again.
Operations are disabled.
\ The built-in microprocessor may malfunction due to
external electrical interference. Unplug the AC power
cord and then plug it back in.
Unable to operate the System from the remote control.
\ The path between the remote control and the remote
sensor on the System is blocked.
\ The batteries are exhausted.
No sound is heard.
\ Speaker connections are incorrect or loose.
\ Headphones are connected.
The System does not work properly.
\ Many functions of this System are implemented by
microcomputers. If pressing any button does not result
in the normal action, disconnect the AC power cord
from the wall outlet, wait for a while, and connect the
cord again.

Disc/USB Mass Storage Class Device
Operations
The disc/USB mass storage class device does not play.
\ The disc is placed upside down. Place the disc with the
label side up.
\ The disc is recorded with the “packet writing (UDF file
system).” It cannot be played. Check the files you want to
play back.
\ The USB mass storage class device is not connected
properly.

Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.

(See above.)

1 Adjust the hour then the minute for on-time.
2 Adjust the hour then the minute for off-time.
3 Select the playback source—“TUNER-FM,” “TUNER-AM,” “DISC,” “LINE,” or “USB.”
4 For “FM/AM”: Select a preset channel.
For “LINE”: Make the connected device ready for playback.
5 Select the volume level.
• You can select the volume level (“VOLUME 0” to “VOLUME 31” and “VOLUME – –”). If you select
“VOLUME – –,” the volume is set to the last level when the System is turned off.
Turn off the System (on standby).
• When the on-time of the daily timer comes, the System sets the volume level gradually to the preset level
after about 10 seconds.

• To exit from the timer setting, press CLOCK/TIMER as required.
• To correct a misentry during the process, press CANCEL. You can return to the previous step.

1
2

If the recorded sound on the Digital Audio Player connected
to the LINE OUT jack is too loud or too quiet, you can change
the audio output level through the LINE OUT jack (without
changing the volume level).

To get the best performance of the System, keep your discs
and mechanism clean.
Handling discs
• Remove the disc from its case by holding it at the edge
while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the disc.
• Put the disc back in its case after use.
• Be careful not to scratch the surface of the disc when
placing it back in its case.
• Avoid exposure to direct sunlight, temperature extremes,
and moisture.
To clean the disc:
• Wipe the disc with a soft cloth in a straight line from center
to edge.
Cleaning the System
• Stains should be wiped off with a soft cloth. If the System is
heavily stained, wipe it with a cloth soaked in water-diluted
neutral detergent and wrung well, then wipe clean with a
dry cloth.
• Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the
following:
– DO NOT wipe it hard.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as insecticides
to it.
– DO NOT allow any rubber or plastic to remain in contact
for a long time.

Amplifier section

Hard to listen to broadcasts because of noise.
\ Antennas connections are incorrect or loose.
\ The AM loop antenna is too close to the System.
\ The FM antenna is not properly extended and
positioned.
\ Electrostatic discharge from your body may cause noise.
If this happens, turn off and on the System again.

Timer Operations
Daily Timer does not work.
\ The System has been turned on when the on-time
comes. Timer starts working only when the System is
turned off.

OUTPUT POWER:
40 W (20 W + 20 W) at 6 Ω (10% THD)
Speakers/Impedance:
6 Ω – 16 Ω
Audio input LINE IN: 500 mV/47 kΩ (at “LINE IN LVL1”)
250 mV/47 kΩ (at “LINE IN LVL2”)
125 mV/47 kΩ (at “LINE IN LVL3”)
Audio output LINE OUT: 1.0 Vrms (47 kΩ) (at “LINE OUT LVL1”)
2.0 Vrms (47 kΩ) (at “LINE OUT LVL2”)
Digital input:
USB MEMORY

This equipment has been designed and manufactured to meet international safety standards but, like any electrical
equipment, care must be taken if you are to obtain the best results and safety is to be assured.

Tuner section

Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.

FM tuning range:
87.50 MHz - 108.00 MHz
AM (MW) tuning range: 522 kHz - 1 629 kHz

Do be careful with glass panels or doors on equipment.

Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between
pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and
withdraw the mains plug when making or changing connections.

CD player section
Dynamic range:
Signal-to-noise ratio:
Wow and flutter:

DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any
way—switch off, withdraw the mains plug and consult your dealer.

88 dB
85 dB
Immeasurable

DON’T remove any fixed cover as this may expose dangerous voltages.

USB storage
USB specification:
Compatible device:
Compatible file system:
Bus power supply:

DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for
unattended operation or has a standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.

Compatible with USB 2.0 Full Speed
Mass storage class
FAT16, FAT32
Max. 500 mA

DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic
safety. It is illegal to watch television whilst driving.

Speakers
Speaker units:
Impedance:
Dimensions (approx.):
Mass (approx.):

10 cm cone x 1
6Ω
145 mm x 251 mm x 162 mm
(W/H/D)
1.6 kg each

DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.

General

DON’T use makeshift stands and NEVER fix legs with wood screws—to ensure complete safety always fit the
manufacturer’s approved stand or legs with the fixings provided according to the instructions.

Power requirements:
AC 230 V , 50 Hz
Power supply to USB mass storage class device:
5 V/500 mA
Power consumption:
22 W (power on)
3.0 W (standby mode)
1.5 W or less (Save Mode)
Dimensions (W x H x D): 175 mm x 251 mm x 247 mm
Mass:
2.6 kg
Specifications and appearance are subject to change without
prior notice.

DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
– NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case
—this could result in a fatal electrical shock.;
– NEVER guess or take chances with electrical equipment of any kind—it is better to be safe than sorry!

Press repeatedly to select “DAILY 1,”
“DAILY 2,” or “DAILY 3.”

To turn on the Daily Timer again, select one of the timer
settings by pressing CLOCK/TIMER, then press SET.

Press and hold to change the audio
output level when the System is turned
on.
You can select one of two levels
alternately as follows:

6

Radio Operations

SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”

Specifications

To Turn Off the Daily Timer

To Select the Audio Output Level

MP3/WMA groups and tracks are not played back as you
expect.
\ The playing order is determined when the groups
and tracks were recorded. It depends on the writing
application.
The disc/USB mass storage class device sound is
discontinuous.
\ The disc is scratched or dirty.
\ MP3/WMA files have not been properly copied into the
USB mass storage class device.
The USB mass storage class device sound stops.
\ Noise and static electricity may stop the sound. In this
case, disconnect and connect the USB mass storage
class device again after turning off the System.
The disc tray does not open or close.
\ The AC power cord is not plugged in.
\ Disc ejection is prohibited (see page 4).

7

Setting the Clock and Daily Timer
Quick Portable Link (QP Link) automatically switches the
source to LINE as the Digital Audio Player connected to the
LINE IN jack starts playback.

General

JVC bears no responsibility for any loss of data in USB mass
storage class device while using this System.

5

Listening to Digital Audio Player

If you are having a problem with your System, check this list
for a possible solution before calling for service.

Listening to Digital Audio Player (see page 6)
• When the sound signal from the Digital Audio Player is too
weak, QP Link may not function correctly.
In this case, turn up the volume of the Digital Audio Player
so that the System can detect the sound signal properly.
• Changing from “LINE” to another source while QP Link works
will deactivate QP Link temporarily.
In this case, the following reactivate QP Link:
– Pressing and holding QP LINK on the remote control.
– When no sound signal comes from the LINE IN jack for
about 30 seconds after the System is turned off.
button to turn the System off or if preset
• If you press
Timer turns the System off while QP Link works, the System
deactivates QP Link temporarily. In such cases, the following
reactivate QP Link:
– When no sound signal comes from the LINE IN jack for
about 30 seconds after the System is turned off.
– When you turn on the power again.
Setting the Clock and Daily Timer (see page 6)
• You can set the clock and Daily Timer while the Save mode
is turned on. While setting the clock or Daily Timer, the
display is turning on.
• The clock may gain or lose 1 to 2 minutes per month. If this
happens, readjust the clock.
• When you unplug the AC power cord or if a power failure
occurs, the clock and the timer will be canceled. You need
to set the clock first, then the timer again.
Timer Priority:
• If you set the Sleep Timer after Daily Timer starts playing the
selected source, Daily Timer is canceled.

8



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2007:01:26 18:38:51
Producer                        : Acrobat Distiller 4.05 for Macintosh
Author                          : JVC
Creator                         : Adobe InDesign CS (3.0.1)
Title                           : UX-G37/UX-G38
Modify Date                     : 2007:02:08 17:15:19+08:00
Subject                         : GNT0080-001A
Page Count                      : 2
Page Mode                       : UseThumbs
Page Layout                     : SinglePage

EXIF Metadata provided by EXIF.tools