Jablotron JA80A Wireless outdoor siren User Manual Exhibit 7 Instruction manual JA 80A

Jablotron Ltd Wireless outdoor siren Exhibit 7 Instruction manual JA 80A

Instruction Manual

JA-80A wireless outdoor siren MHV51101_c1 1 The JA-80A wireless outdoor siren The JA-80A is a component of Jablotron’s Oasis 80 system. It is designed to sound an external alarm and to indicate any tampering it experiences. It is powered by a long-life lithium battery and communicates wireless using Jablotron Oasis protocol. BAT - 80100158160230 Installation The siren should be installed by a certified installer. It should be located on a vertical wall with its flashing light facing downwards. The siren should not be shielded by any metal which could block radio communication. 1. Open the siren cover (2 screws on the bottom side) 2. Remove the internal transparent cover (release its screw and push it to the right) 3. Attach the siren to the desired location (3 screws) 4. Select the desired optional features via the internal jumpers (see the following description) 5. Enroll the siren to the control panel as follows: a) Set the control panel to Service mode and key in 1 to enter enrollment mode (the desired address can be selected by using the arrow keys) b) Connect up the battery cable in the siren – (the light will flash and after a while it will turn off = enrollment finished) c) Exit enrollment mode by pressing the # key 6. Reinstall the internal and external covers Notes: • Multiple sirens can be enrolled to the control panel • If the siren continues flashing it has not been enrolled – check if the control panel is in enrollment mode and if it has its antenna connected. The siren should be at least 2 meters away from the control panel during enrollment. Jumpers 50 / 25 selects how often the siren checks the status of the system. In normal operation the siren saves battery power by turning its receiver off. It then turns on again periodically to check for alarms in the system approximately every 25 or 60 seconds (selectable). The 60 second period not only extends the siren’s maximum reaction delay but also its battery life. LED ON / OFF enables short flashes of the siren every 60 seconds (= position ON). If OFF is selected, the siren will flash only while indicating an alarm. Siren connector(beware of high voltages)LEDs Top cover sensor Siren removal sensor Battery connectorenableddisabledcommunicationinterval 25sinterval 60sLED indicationantenna Function If there is an external alarm in the control panel, the siren will start sounding and flashing (can be delayed – see the 50/25 jumper). The siren will sound for a maximum of 3 minutes (unless the control panel alarm period is shorter) and its light will flash 30 minutes longer. Siren indication can also be stopped by ending the alarm in the control panel. If tampered with, the siren will send a tamper signal to the system Warning – beware of electrical shocks when the siren sounds (it generates a high AC voltage – do not touch any internal parts). Switch the system to Service mode before performing any maintenance on the siren. Remember, that the siren can start sounding and flashing anytime when its battery is connected. Testing If you trigger an external alarm in the system, the siren should start working within 25 (or 60) seconds. To measure the siren’s signal strength select signal measurement mode in the control panel and activate the siren tamper sensor by opening its cover. Battery replacement The siren checks its battery status and if it is going to be discharged soon it will inform the system (which will notify the user and service technician). The siren will continue to work, but its battery should be replaced within 2 weeks. Only use a Jablotron BAT-80 battery as a replacement. Never try to charge the battery. When disposing of the used battery always follow local regulations. Removing the siren from the system If you want to uninstall the siren, do not forget to erase it in the control panel to avoid any indication of lost communication with the siren. Specifications power lithium battery BAT-80 Jablotron battery life time calculated for max 5 years (60 sec supervision) communication band 868 MHz, Oasis protocol communicating distance up to 300m (open area) siren piezo electric, 112 dB/1m max. duration of the audible alarm 3 minutes max. duration of flashing during alarms 30 minutes enclosure IP34D EN 50131-1 grade 2 dimensions 230 x 158 x 75 mm working temperature -25 to +60°C operating environment class IV. can be operated according to ERC REC 70-03 FCC ID: VL6JA80A Jablotron Ltd. hereby declares that the JA-80A is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC and complies with part 15 of the FCC rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired operation, and 3 the jumper 25/50 must be set to 50. CAUTION: Changes or modifications no expressly approved by Jablotron could void the user´s authority to operate the equipment. The original of the conformity assessment can be found at www.jablotron.com, Technical Support section Note: Although this product does not contain any harmful materials we suggest you return the product to the dealer or directly to the producer after use.

Navigation menu