Jablotron JA80H Outdoor keypad and RFID card reader User Manual Exhibit 7 Instruction manual JA80H

Download:
Mirror Download [FCC.gov]
Document ID	877183
Application ID	Bj58Z/ZnZbWa45jWrtwbqg==
Document Description	Instruction Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.53kB (44124 bits)
Date Submitted	2007-12-07 00:00:00
Date Available	2007-12-07 00:00:00
Creation Date	2007-11-23 11:50:28
Producing Software	AFPL Ghostscript 8.53
Document Lastmod	2007-11-23 11:50:28
Document Title	Exhibit 7 Instruction manual JA80H
Document Creator	FreePDF XP 3.05 - http://shbox.de
Document Author:	eschlemmer

The JA-80H outdoor keypad and RFID card reader
Housing
IP65 (EN 60529)
Mechanical resistance
IK08 (EN 50102)
Working environment
class IV(EN 50131-1)
Operational temperature
-25 to +60°C
RFID card
Jablotron PC-01 or PC-02 (EM UNIQUE 125 kHz)
Dimensions
46 x 150.5 x 22.5mm
Length of the connection cable
1m
Complies with grade 2 (EN 50131-1, TS 50131-3)
Complies with
ANSI C63.4
Can be operated according to ERC REC 70-03, FCC Part 15
The JA-80H is a component of Jablotron’s Oasis
80 alarm system. It is designed to control access
(door lock) or to control a security system and
connects to the Oasis control panel via a WJ-80
interface.
Alternatively it can be connected to an AS-80 unit
as a part of a stand-alone access system.
The keypad sends data in Wiegand 26b format.
Installation
Installation shall only be undertaken by
technicians holding a certificate issued by an
authorized distributor. It is usually placed near an
entrance door (equipped with an electric lock). The
keypad can be used outdoors (conforms to IP-65).
1. Open the rear cover by unscrewing the screw
2. Prepare a hole in the wall for the keypad cable to
pass through, where the keypad will be located.
3. Attach the rear cover to the desired location (the
tamper spring must be properly pressed)
4. Pull the keypad cable through the wall hole and to the
interface unit’s box (WJ-80, AS-80)
5. Attach the keypad to the rear cover and secure it
using the screw
6. Connecting and setting up the keypad is described in
the WJ-80 or AS-80 manuals.
FCC ID VL6JA80H
Jablotron Ltd. hereby declares that the JA-80H is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC and complies with part 15 of
the FCC rules. Operation is subject the the following two
conditions: 1. This device may not cause harmful interference,
and 2. this device must accept any interference received,
including interference that may cause undesired operation.
The original of the conformity assessment can be found at
www.jablotron.com, Technical Support section CAUTION:
Changes or modifications no expressly approved by Jablotron
could void the user´s authority to operate the equipment
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the producer after use.
Cabling
wire
red
green
brown
white
grey
yellow
blue
pink
cca 1 m
signal
+12V (power supply, 60mA)
D0 (Wiegand 26b data output)
D1 (Wiegand 26b data output)
TMP (normally closed tamper contact)
TMP (normally closed tamper contact)
BZR (input controlling keypad sound – connecting to GND
generates a beep on the keypad)
GND (common ground)
not connected
Configuring the keypad for operation with the WJ-80
151,5
Technical specifications
Power supply
Stand-by consumption
45
10 to 16V
typically 60mA
87,5
TAMPER
If the JA-80H keypad is connected to an Oasis control panel via a WJ-80
and it does not work as described in the manual, then it is not set to the
correct (factory default) operational mode. In such a case:
1. Switch the Oasis control panel to service mode
2. Disconnect the power from the control panel (mains and battery)
3. Disconnect the yellow and brown keypad wires from the terminals
and connect them together.
4. Power-up the control panel (keypad starts beeping)
5. Disconnect the yellow and brown wires (beeping will terminate)
6. On the JA-80H keypad, press button 4 (beeps once) and then button 3
(beeps several times)
7. Disconnect the power from the control panel, connect the yellow and brown
wires back up, power-up the control panel and check the proper functioning
of the JA-80H keypad
22,5
Note: The red LED is lit in Oasis normal operating mode. Pressing a button
is confirmed by a flash from the orange LED.
How to set up the JA-80H keypad for the AS-80 access system is described in the AS-80 manual.
The JA-80H outdoor keypad and RFID card reader
MKM51100FCC

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 1
Producer                        : AFPL Ghostscript 8.53
Create Date                     : 2007:11:23 11:50:28
Modify Date                     : 2007:11:23 11:50:28
Title                           : Exhibit 7 Instruction manual JA80H
Creator                         : FreePDF XP 3.05 - http://shbox.de
Author                          : eschlemmer

EXIF Metadata provided by EXIF.tools