Jablotron RC88 Wireless wall button User Manual Exhibit 7 Instruction manual RC88

Download:
Mirror Download [FCC.gov]
Document ID	878592
Application ID	8t1K1VHsY3VYJlQ5lUF2iw==
Document Description	Users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.98kB (49794 bits)
Date Submitted	2007-12-12 00:00:00
Date Available	2007-12-12 00:00:00
Creation Date	2007-11-23 12:43:51
Producing Software	AFPL Ghostscript 8.53
Document Lastmod	2007-11-23 12:43:51
Document Title	Exhibit 7 Instruction manual RC88
Document Creator	FreePDF XP 3.05 - http://shbox.de
Document Author:	eschlemmer

The RC-88 wireless wall button
The RC-88 is a component of Jablotron’s Oasis 80 alarm system. It is
designed to be a remote control for setting/unsetting (arming/disarming)
an alarm system, triggering panic alarms or remotely controlling other
appliances. The battery-powered wireless button communicates via
OASIS radio protocol.
Using the button with an Oasis JA-80K panel
When used with a control panel, the tamper contacts should be switched
on (DIP switch # 1 in the ON position).
1. Enter enrollment mode on the control panel by keying in “1” in Service
mode (the desired device address can be chosen by the arrow keys).
Installation
2. Install a battery into the RC-88 to activate enrollment.
If it is to be used as a panic button, then it must be installed together with
the bottom part of its housing and the tamper contacts must be switched on.
Do not install the button on a metal surface (it adversely affects the range of
its transmitter).
• Remove the top part of the housing (using a screwdriver from the right/left
side).
• Release the bottom part of the housing by pressing the 4 tabs in the
corners.
• Install the bottom part to the desired place.
• Reunite the housing containing the electronics with the installed part of the
housing (the tamper spring should press against the wall where the unit is
to be installed, via the hole in the bottom housing).
• Configure the functionality using the DIP switches (see the below section
called ‘Setting the DIP switches’).
• Enroll the RC-88 button to its receiver or control panel according to the
relevant manual.
• Reunite the top housing with the rest of the housing to complete
installation.
3. Exit enrollment mode by pressing “#”.
If DIP switch # 2 is OFF, the Natural reaction of the control panel is
remote control - button A = set and button B = unset. If any other
reaction is set in the control panel, it will only be valid for button A.
If DIP switch # 2 is ON, then the natural reaction of the control panel is a
panic alarm – triggered by pressing button A or B.
Testing the RC-88 using a control panel
In service mode, an Oasis control panel can check the radio signal
strength of an enrolled RC-88 button (see control panel manual).
Using the RC-88 as a doorbell button
If the RC-88 is to be used with a JA-80L indoor siren as a door bell
button, set DIP switches #1 and #2 to the OFF position. Enrollment is
described in the JA-80L manual.
Using the RC-88 to control electrical appliances
The RC-88 button can also be used with other Jablotron products which
communicate via Oasis radio protocol, e.g. relay receiving modules series
UC-8x and AC-8x (see the manuals of these particular products for
details). For these applications we recommend switching DIP switches #1
and #2 OFF.
Note: The RC-88 can be enrolled to several receivers at once.
If the button is used with an Oasis control panel and DIP switch # 1 is ON,
then the control panel monitors the voltage of the RC-88’s battery and if too
low, the control panel informs the installer or user. The button continues to
function but battery replacement should not be delayed by more than two
weeks. This should be done by a qualified technician with the control panel
in Service mode.
Expired batteries should not be thrown into the garbage, but disposed of
according to local regulations.
Always test the proper functioning of the RC-88 after battery replacement.
TOP
LITHIUM
3V 1/2 AA
TOP
Battery replacement
Technical Specifications
ON
Voltage:
Lithium battery type CR14250SL (1/2AA 3.0V)
Typical battery lifetime:
- approximately 3 years (DIP switch #1 ON, 20 daily activations)
- approximately 5 years (DIP switch #1 OFF, 20 daily activations)
Communication band:
868 MHz, Oasis protocol
Communication range
approx. 300 metres (open area)
Dimensions
80 x 80 x 29 mm
Operational environment according to EN 50131-1
class II. Indoor general
Operational temperature range
-10 to + 40 °C
Complies with EN 50131-1, EN 50131-5-3
grade 2
ANSI C63.4
Can be operated according to
EKC REC 70-03, FCC Part 15
Setting the DIP switches
Set DIP switches #1 and #2 before finally closing the RC-88 unit as below:
OFF
Tamper contacts, radio
communication and low battery
supervision switched OFF
Remote control function - button
A (push the button’s top)= set, B
(push the button’s bottom) =
unset
ON
Tamper contacts, radio
communication and low battery
supervision switched ON
Panic button function (button A or B
sends a panic signal, i.e. any
pushing)
FCC ID VL6RC88
Jablotron Ltd. hereby declares that the RC-88 is in compliance
with the essential requirements and other relevant provisions of
Directive 1999/5/EC and complies with part 15 of the FCC rules.
Operation is subject the the following two conditions: 1. This
device may not cause harmful interference, and 2. this device
must accept any interference received, including interference
that may cause undesired operation.
The original of the conformity assessment can be found at
www.jablotron.com, Technical Support section CAUTION: Changes or
modifications no expressly approved by Jablotron could void the user´s
authority to operate the equipment
Note:
Although
this
product does not contain
any harmful materials we
suggest you return the
product to the dealer or
directly to the producer after
use.
The RC-88 wireless wall button
MKD51100FCC

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 1
Producer                        : AFPL Ghostscript 8.53
Create Date                     : 2007:11:23 12:43:51
Modify Date                     : 2007:11:23 12:43:51
Title                           : Exhibit 7 Instruction manual RC88
Creator                         : FreePDF XP 3.05 - http://shbox.de
Author                          : eschlemmer

EXIF Metadata provided by EXIF.tools