Jakks Pacific 87374RX XPV/MARVEL - RC HULK SMASH User Manual 87374 CAN HulkSmashIS0206rev

Download:
Mirror Download [FCC.gov]
Document ID	2577118
Application ID	tZ8RR09CLaGt5uaajTPpeA==
Document Description	User Manual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	56.88kB (710996 bits)
Date Submitted	2015-04-07 00:00:00
Date Available	2015-04-07 00:00:00
Creation Date	2015-03-30 13:43:56
Producing Software	Adobe PDF library 11.00
Document Lastmod	2015-03-30 13:43:56
Document Title	87374_CAN_HulkSmashIS0206rev
Document Creator	Adobe Illustrator CC 2014 (Macintosh)

87374-CAN XVP Hulk Smash IS
size:22” W x 8.5”H x 2
Color: Grayscale
®
4+
#87374
2.4GHz
HULK SMASH RC
INSTRUCTIONS
* Please remove try-me cable from
VEHICLE and REMOTE CONTROL
before use.
CAUTION:
ALWAYS PLAY IN SAFE SURROUNDINGS,
AWAY FROM STREETS OR MOVING VEHICLES.
REMOTE CONTROL:
X2 1.5V AA (LR6)
ALKALINE BATTERIES
REQUIRED
OPERATION
SPIN MODE
4. Press SPIN BUTTON to have the vehicle spin for 10 seconds. Hold down the SPIN BUTTON
to keep the vehicle spinning.
NOTE: Hulk’s arms need to be in the same position on each side.Rotate left arm FORWARD/
BACKWARD if necessary to match right arm position.
NOTE: Wheelie SPIN is un-achieveable if fist’s
starting position is at front of toe.
Low Speed
High Speed
2. Plug Hulk’s left arm in and
push until the arm is completely
attached with the body.
TRY ME
FORWARD
CORRECTION
If the VEHICLE flips over, first try to continue pushing the joystick FORWARD. When Hulk’s arms are
not in the same position on each side, the vehicle may not always self-right.
Tips: Try to lower down the forward speed if the vehicle keep flipping over continously.
OFF / ON SWITCH
1. Locate and open BATTERY COVER as shown.
Use a Philips/cross head screwdriver (not included)
to loosen screws. Screws remain attached to the cover.
2. Install 2 – 1.5V AA (LR6) ALKALINE BATTERIES in the
orientation shown.
3. Replace BATTERY COVER and tighten screws.
BATTERY SAFETY INFORMATION
WARNING!
Battery acid leakage can cause personal injury and cause damage to the product and
battery acid away from eyes, ears, nose and mouth. Immediately wash any clothing or other surface that
comes in contact with leaked battery acid. Leaking batteries may make "popping" sounds. Dispose
according to Local, State or Federal Battery Laws.
VEHICLE
2. Locate and open BATTERY COVERS
on BACK and BOTTOM of the vehicle as
shown.
Use a Phillips/cross head screwdriver
(not included) to loosen screws. Screws
remain attached to cover.
TO AVOID BATTERY PROBLEMS:
NEVER mix old and new batteries or different brands of batteries.
NEVER mix alkaline, standard (carbon-zinc), rechargeable (nickel-cadmium) batteries with this product.
NEVER dispose of batteries in fire, as they may leak and explode.
NEVER use rechargeable batteries.
ALWAYS remove exhausted batteries from toy.
ALWAYS have an adult install batteries consistent with installation instructions.
ONLY use batteries specified by manufacturer.
Batteries are to be inserted with the correct polarity.
The supply terminals are not to be short-circuited.
Non-rechargeable batteries are not to be recharged.
3. Replace / install 4 - 1.5V AA (LR6)
ALKALINE BATTERIES in the back and
2 - 1.5V AA (LR6) ALKALINE BATTERIES in
the BOTTOM in the orientation shown.
4. Replace BATTERY COVERS and tighten
screws.
Note: Always replace all 6 batteries at the
same time.
BACK
3. Press SPIN BUTTON to move SMASHING ARMS into WHEELIE position. Vehicle will
SPIN for five seconds. Keep pressing the SPIN BUTTON for longer spinning time.
VEHICLE
1. VEHICLE: Move the ON/OFF/TRY-ME SWITCH
to the ON position.
2. REMOTE CONTROL: Move the OFF / ON SWITCH
to the ON position.
NOTE: Wheelie SPIN does not success all of the time due to a combination of fist position/floor
friction/battery power factors. If wheelie SPIN does not success, repeat SPIN mode one or more times.
3. Place the VEHICLE on ground and point the
REMOTE CONTROL directly at the VEHICLE.
The LED light on REMOTE CONTROL will flash
when pairing with the VEHICLE. Pairing process
is completed when the LED light is solid on and
the VEHICLE is ready to go.
Use the FORWARD/ROTATE to maneuver
the VEHICLE.
CUSTOM SMASH MODE
There are EIGHT different positions for the SMASHING ARMS.
Each position gives different forward driving actions based on
when the FISTS hit the ground.
ON/OFF/TRY-ME SWITCH
- NEVER drive near traffic, buildings, trees,
people or other obstructions.
- NEVER operate during storms or other
adverse weather conditions.
- ALWAYS point away from face, eyes, people,
animals and property when driving.
- ALWAYS use alkaline batteries only.
PROBLEM
Vehicle won’t move.
2. Drive VEHICLE forward, SMASHING ARMS will
nudge the VEHICLE left or right in different
combinations to find new results.
Note: When LED light on REMOTE CONTROL
is keep flashing, switch off both VEHICLE
and REMOTE CONTROL and repeat
pairing process.
- Never use in water or mud.
- Never use near glass and other fragile objects.
TROUBLESHOOTING
1.To change arm position, rotate LEFT ARM forward or
backwards the desired number of clicks.
Pairing is required every time the VEHICLE/
REMOTE CONTROL is turn ON.
TRY ME
JAKKS Pacific® Battery, Solar or Electrically-Operated Product 90 DAY LIMITED WARRANTY
Pour produit à fonctionnement électrique, solaire ou à piles de JAKKS Pacific® GARANTIE LIMITÉE DE 90 JOURS
IMPORTANT SAFETY INFORMATION
1. Push joystick FORWARD to drive VEHICLE forward with powered SMASHING ARMS.
The more the joystick push FORWARD, the higher the VEHICLE speed.
2. Pull joystick BACKWARDS to spin VEHICLE without powering SMASHING ARMS.
This will TURN and change direction of the VEHICLE.
The more the joystick push BACKWARD, the higher the VEHICLE speed.
Tips: Keep hand position over the floor to have the best performance.
POSSIBLE CAUSE
Vehicle / Remote Control switch is
switched OFF.
Move switch to ON position.
Weak Remote Control batteries.
Press any direction button.
If indicator light does not activate,
replace batteries in the Remote
Control.
Vehicle is stuck.
Weak vehicle batteries.
SLOT FOR TRY-ME CABLE
Vehicle won’t do high
speed wheelie spins
after pressed spin
button.
SOLUTION
Move vehicle to a smoother
surface, clean tires, make sure
surface or floor is clean as well.
Replace batteries.
Remote Control is not close enough
to vehicle.
Make sure the Remote Control is
placed within the signal receiving
range.
Large friction between tires and floor.
Use on tile, hardwood floor and
other smooth hard surfaces.
Hulk’s arms are not in the same position
on each side.
Rotate left arm forward or
backwards the desired number
of clicks.
weak vehicle batteries.
Replace batteries.
TRY ME
BOTTOM
Note: This vehicle is for indoor use only. Works best
on tile, hardwood floor and other smooth hard surfaces.
Not recommended for use on carpets, grass, loose dirt,
wet surface or concrete. Never use in water or mud.
Never use near glass and other fragile objects.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil répond aux exigences du chapitre 15 de la FCC. Son utilisation respecte les deux conditions suivantes :
(1) Cet appareil ne risque pas de causer d’interférences dangereuses et (2) Cet appareil supporte tout type d’interférences, y compris celles pouvant altérer son fonctionnement.
MISE EN GARDE : tout changement ou modification non approuvés expressément par le fabricant responsable de la conformité pourrait annuler le droit d’usage lié au fonctionnement
de l’appareil.
REMARQUE : cet appareil a été testé et vérifié conforme aux normes du chapitre 15 de la FCC relatives aux appareils numériques de classe B. Ces normes visent à offrir une protection
acceptable contre les interférences dangereuses dans une installation résidentielle. Cet appareil génère, utilise et peut émettre des ondes radio. Il peut altérer les communications
radio s’il n’est pas installé et utilisé conformément aux instructions. Cependant, rien ne peut garantir l’absence d’interférences dans une installation particulière. Les interférences
avec la radio ou la télévision hertzienne peuvent être mises en évidence en allumant et en éteignant l’appareil. Les manipulations suivantes permettent de corriger de telles
interférences :
- Changer l’emplacement ou l’orientation de l’antenne de réception.
- Augmenter la distance entre les appareils en cause.
- Brancher les appareils sur deux prises électriques distinctes.
- Consulter le revendeur ou un technicien radio/TV expérimenté si nécessaire.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter dout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre
le fonctionnement.
CAN ICES-3 (B)/NMB-3(B)
ROTATE
REMOTE CONTROL
NOT INCLUDED
© MARVEL
REMO TE CON TROL
ADULT ASSEMBLY REQUIRED
1. Take Hulk’s left arm and locate
the junction on the left of Hulk’s
body.
Align the rib on arm to the slot of
hexagonal junction.
1. Unplug the Try-me cable at the back
of vehicle and remote control.
TM & © 2015 MANUFACTURED BY JAKKS PACIFIC, INC., 2951 28TH STREET, SANTA MONICA, CA 90405 U.S.A.
All other symbols, marks, logos, and designs (collectively “Trademarks”) are Trademarks of and proprietary to their respective owners
and used under license. Contents may vary in style, color, shape and decoration from images shown on package or in advertising.
Questions or comments? www.jakks.com, consumers@jakks.com, or 1-877-875-2557 in North America.
Retain packaging and instructions since they contain important information. MADE IN CHINA.
High Speed
Low Speed
SPIN BUTTON
ADULT INSTALLATION REQUIRED
Requires 6 “AA” (LR6) ALKALINE BATTERIES
for vehicle and 2 “AA” (LR6) ALKALINE
BATTERIES for remote control.
Batteries for the vehicle are included.
When performance diminishes,
replace with fresh batteries.
CONTENTS:
- RC VEHICLE
- REMOTE CONTROL
- HULK’S LEFT ARM
CONTROLS
SLOT FOR TRY-ME CABLE
BATTERY REPLACEMENT / INSTALLATION
ADULT SUPERVISION REQUIRED
VEHICLE:
X6 1.5V AA (LR6)
ALKALINE BATTERIES
INCLUDED
ARM ASSEMBLY INSTRUCTION
Thanks for purchasing a great JAKKS Pacific® product! Please immediately register your product online at www.jakks.com/warranty. Registration is not required
for the effectiveness of this limited warranty.
IMPORTANT NOTICE TO CONSUMER:
This 90 DAY LIMITED WARRANTY applies to the original product purchaser, provided the product: 1) was purchased from an authorized JAKKS™
distributor/dealer/retailer, and 2) is returned at your expense, postage pre-paid and insured, along with the original dated sales receipt to the address noted below.
Please save a copy of your original sales receipt, as the original receipt will not be returned to you.
If you return the product to us without the original dated sales receipt, this warranty coverage will not apply. If the product is determined by JAKKS to be defective
and returned to JAKKS within the 90 day warranty period, we will (at our option) repair or replace it. Return shipment to you may take up to
6 weeks, depending upon your location. If your product is repaired or replaced, it will be warranted for the longer of the original warranty or for 30 days after
warranty service.
SCOPE OF LIMITED WARRANTY: The product is warranted to be: a) tested and inspected before shipment, and b) free of defects in material and workmanship
for 90 days from date of purchase. If a covered defect occurs within the warranty period, then at our sole option, we will repair or replace the product or provide
you with another product of equal value.
WHAT IS NOT COVERED BY LIMITED WARRANTY:
THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN MODIFIED OR REPAIRED BY USER OR OTHERS OR IF IT HAS BEEN DAMAGED AS A RESULT
OF ACCIDENT, IMMERSION IN WATER, NEGLECT, ABUSE, MISUSE, BATTERY LEAKAGE, IMPROPER BATTERY
INSTALLATION, UNAUTHORIZED SERVICE, LOSS OF PARTS, WEATHER, ACTS OF GOD, ANY ACTION OR OMISSION WHICH CONSTITUTES A
DEVIATION FROM THE OPERATING INSTRUCTIONS, OR ANY OTHER CAUSES NOT ARISING OUT OF DEFECTS IN
WORKMANSHIP OR MATERIALS.
EXCLUSIONS FROM LIMITED WARRANTY: THIS WARRANTY IS EXCLUSIVE OF AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES
RELATED TO THIS PRODUCT, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SPECIAL, INCIDENTAL AND CONSEQUENTIAL DAMAGES ARISING
FROM POSSESSION, USE, OR MALFUNCTION OF THIS PRODUCT ARE EXCLUDED BOTH FOR PROPERTY DAMAGE AND PERSONAL INJURY TO THE
EXTENT LEGALLY PERMITTED.
ADDITIONAL LEGAL RIGHTS: This warranty provides specific legal rights. You may have other or different rights in your state or country.
QUESTIONS OR COMMENTS: If you experience product difficulties or have questions or comments, you may contact our Consumer Relations department as
follows:
Phone: 877-875-2557 (toll-free, North America only) or 909-594-7771 (Monday-Friday, 7:30AM-4:30PM Pacific/
GMT -8).
Mail: JAKKS Consumer Relations, 21749 Baker Parkway, Walnut, California USA 91789.
Email: consumers@jakks.com
WHEN WRITING TO US: Please include: 1) product name; 2) item number; 3) purchase date; 4) description of the problem being experienced; and 5) your name,
address and phone number. Additionally, if eligible under the warranty and so advised by JAKKS Consumer Relations, also include the defective product and the
ORIGINAL dated sales receipt evidencing product purchase. Please retain a copy of your receipt.
Nous vous remercions d’avoir fait l’acquisition de cet article de JAKKS Pacific® !
Veuillez enregistrer immédiatement votre article en ligne à www.jakks.com/warranty. L’enregistrement n’est pas requis pour bénéficier de cette garantie limitée.
AVIS IMPORTANT AU CONSOMMATEUR :
Cette GARANTIE LIMITÉE DE 90 JOURS est cédée à l'acheteur original du produit, à condition que ce dernier : 1) ait été acheté auprès d’un revendeur/distributeur/détaillant agréé de JAKKS™ et
2) soit renvoyé à vos frais, sous pli préaffranchi et assuré,
accompagné du reçu daté d’achat original à l’adresse indiquée plus bas.
Veuillez conserver une copie du reçu d’achat original car celui-ci ne vous sera pas renvoyé. Si vous nous renvoyez le produit sans le reçu d’achat original, l’article
ne sera pas couvert. Si le produit est jugé défaillant par JAKKS et nous a été renvoyé dans le délai de garantie de 90 jours, nous nous réservons l’option de le
réparer ou le remplacer. L’expédition de retour peut prendre jusqu’à 6 semaines en fonction de la localité d’envoi. Si l'article est réparé ou remplacé, il sera sous
garantie pendant la période de garantie d'origine ou pendant 30 jours après l’intervention sous garantie, à savoir la période la plus longue.
ÉTENDUE DE LA GARANTIE LIMITÉE : Il est garanti que ce produit a été : a) testé et inspecté avant l’expédition et b) jugé exempt de vice de matière et de
fabrication pendant 90 jours à compter de la date d’achat. Si un vice couvert aux présentes vient à se déclarer pendant la période sous garantie, nous nous
réservons l'option de réparer ou remplacer l'article ou d'offrir un autre produit à valeur équivalente.
CE QUE LA GARANTIE LIMITÉE NE COUVRE PAS :
LA PRÉSENTE GARANTIE EST NULLE SI LE PRODUIT A FAIT L'OBJET DE MODIFICATIONS OU DE RÉPARATIONS PAR L’UTILISATEUR OU AUTRUI OU
S'IL A ÉTÉ ENDOMMAGÉ À LA SUITE D'UN ACCIDENT, D'IMMERSION DANS L'EAU, DE
NÉGLIGENCE, D'UTILISATION ABUSIVE, D’UTILISATION INCORRECTE, DE PILE(S) AYANT COULÉ, D'INSTALLATION INCORRECTE DE PILE(S),
D'INTERVENTION NON AUTORISÉE, DE PERTE DE PIÈCES, D'INTEMPÉRIES, DE CATASTROPHES NATURELLES, DE TOUTE ACTION OU OMISSION QUI
CONSTITUE UN ÉCART PAR RAPPORT AUX DIRECTIVES D’EMPLOI OU TOUTE AUTRE RAISON AUTRE QUE CAUSÉE PAR UN VICE DE MATIÈRE OU
DE FABRICATION.
EXCLUSIONS DE LA GARANTIE LIMITÉE : CETTE GARANTIE EXCLUT ET REMPLACE TOUTE AUTRE GARANTIE EXPRESSE OU TACITE CONCERNANT
CET ARTICLE, Y COMPRIS TOUTE GARANTIE TACITE DE QUALITÉ MARCHANDE OU D'ADAPTATION À L’EMPLOI DANS UN BUT SPÉCIFIQUE. LES
DOMMAGES PARTICULIERS, ACCESSOIRES OU IMMATÉRIELS AYANT POUR ORIGINE LA POSSESSION, L’UTILISATION OU LE FONCTIONNEMENT
DÉFECTUEUX DE CET ARTICLE SONT EXCLUS TANT POUR LES DOMMAGES MATÉRIELS QUE LES BLESSURES CORPORELLES, ET CE DANS LA
MESURE PERMISE PAR LA LOI.
DROITS SUPPLÉMENTAIRES : Cette garantie fournit des droits spécifiques. Ils peuvent être différents selon les états, les provinces ou les pays.
QUESTIONS OU COMMENTAIRES : Si cet article présente des problèmes de fonctionnement ou pour toute question ou commentaire, veuillez contacter notre
Service à la clientèle comme suit :
par téléphone : 877-875-2557 (appel sans frais à partir de l'Amérique du Nord uniquement) ou le 909-594-7771 (du lundi au vendredi,
7 h 30 à 16 h 30, heure du Pacifique / GMT - 8).
par courrier : JAKKS Pacific, Inc. Consumer Relations, 21749 Baker Parkway, Walnut, California USA 91789.
Par courriel : consumers@jakks.com
LORSQUE VOUS NOUS ÉCRIVEZ : Veuillez inclure : 1) le nom du produit, 2) le numéro d'article; 3) la date d'achat; 4) la description du problème; et 5) vos
coordonnées et numéro de téléphone. En outre, si l’article est couvert par la présente garantie et si vous en êtes ainsi avisé par notre service à la clientèle,
joignez le produit défectueux et l’ORIGINAL du reçu daté faisant preuve de l’achat. Veuillez conserver une copie de votre reçu d’achat.
080309

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c014 79.156821, 2014/08/29-03:07:50
Format                          : application/pdf
Title                           : 87374_CAN_HulkSmashIS0206rev
Metadata Date                   : 2015:03:30 13:43:56+08:00
Modify Date                     : 2015:03:30 13:43:56+08:00
Create Date                     : 2015:03:30 13:43:56+08:00
Creator Tool                    : Adobe Illustrator CC 2014 (Macintosh)
Thumbnail Width                 : 256
Thumbnail Height                : 76
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 8100 bytes, use -b option to extract)
Instance ID                     : uuid:910a544c-e9e7-6b44-b079-76e47237a12b
Document ID                     : xmp.did:7048be5d-ba5a-4574-b3e6-2071e51579b2
Original Document ID            : uuid:5D20892493BFDB11914A8590D31508C8
Rendition Class                 : proof:pdf
Derived From Instance ID        : uuid:a190f582-1f1d-614a-b3f8-548ad542d4aa
Derived From Document ID        : xmp.did:FB7F1174072068118A6DD2DF5593B59D
Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8
Derived From Rendition Class    : default
History Action                  : saved, saved
History Instance ID             : xmp.iid:F77F1174072068118C14AAA2E9D09DEC, xmp.iid:7048be5d-ba5a-4574-b3e6-2071e51579b2
History When                    : 2015:01:08 10:38:32-08:00, 2015:03:30 13:43:44+08:00
History Software Agent          : Adobe Illustrator CS5, Adobe Illustrator CC 2014 (Macintosh)
History Changed                 : /, /
Startup Profile                 : Print
Has Visible Overprint           : True
Has Visible Transparency        : True
N Pages                         : 1
Max Page Size W                 : 46.277778
Max Page Size H                 : 11.000000
Max Page Size Unit              : Inches
Font Name                       : ArialMT, Arial-BoldMT, Helvetica-Condensed-Bold, Helvetica-Condensed-Black, Helvetica-Light, HelveticaNeue-LightCond, HelveticaNeue-BoldCond, HelveticaNeue-CondensedBlack, HelveticaNeue-Light, HelveticaNeue, HelveticaNeueLTPro-MdCn, MyriadPro-BoldCond, MyriadPro-Regular, MyriadPro-Bold
Font Family                     : Arial, Arial, Helvetica, Helvetica, Helvetica, Helvetica Neue, Helvetica Neue, Helvetica Neue, Helvetica Neue, Helvetica Neue, Helvetica Neue LT Pro, Myriad Pro, Myriad Pro, Myriad Pro
Font Face                       : Regular, Bold, Bold Condensed, Black Condensed, Light, 47 Light Condensed, 77 Bold Condensed, Condensed Black, Light, Regular, 67 Medium Condensed, Bold Condensed, Regular, Bold
Font Type                       : Open Type, Open Type, Type 1, Type 1, TrueType, Type 1, Type 1, TrueType, TrueType, TrueType, Open Type, Open Type, Open Type, Open Type
Font Version                    : Version 5.06, Version 5.06, 001.002, 001.002, 7.0d20e1, 001.000, 001.000, 7.0d27e1, 7.0d27e1, 1.1d4, Version 1.000;PS 001.000;Core 1.0.38, Version 2.006;PS 002.000;Core 1.0.38;makeotf.lib1.6.6565, Version 2.007;PS 002.000;Core 1.0.38;makeotf.lib1.7.9032, Version 2.062;PS 2.000;hotconv 1.0.57;makeotf.lib2.0.21895
Font Composite                  : False, False, False, False, False, False, False, False, False, False, False, False, False, False
Font File Name                  : Arial.ttf, Arial Bold.ttf, HelveConBol; Helvetica Cond.Agency, HelveConBla; Helvetica-Condensed-Black, Helvetica.dfont, HelveNeuLigCon; HelveticaNeue-LightCond, HelveNeuBolCon; HelveticaNeue-BoldCond, HelveticaNeue.dfont, HelveticaNeue.dfont, HelveticaNeue.dfont, HelveticaNeueLTPro-MdCn.otf, MyriadPro-BoldCond.otf, MyriadPro-Regular.otf, MyriadPro-Bold.otf
Plate Names                     : Cyan, Magenta, Yellow, Black, PANTONE Cool Gray 7 C, PANTONE Black C
Swatch Groups Colorants Tint    : 100.000000
Swatch Groups Group Name        : Brights
Swatch Groups Group Type        : 1
Swatch Groups Colorants Swatch Name: C=60 M=90 Y=0 K=0
Swatch Groups Colorants Mode    : CMYK
Swatch Groups Colorants Type    : PROCESS
Swatch Groups Colorants Cyan    : 60.000000
Swatch Groups Colorants Magenta : 90.000000
Swatch Groups Colorants Yellow  : 0.003100
Swatch Groups Colorants Black   : 0.003100
Producer                        : Adobe PDF library 11.00
Slug Checksum                   : 2812661010
Slug Post Script Name           : Helvetica-Light
Slug Foundry                    : Apple Computer
Slug Version                    : 7.0
Slug Outline File Size          : 0
Slug Family                     : Helvetica
Slug Font Sense 12 Checksum     : 2812661010
Slug Font Kind                  : TrueType
Slug Kerning Checksum           : 0
Page Count                      : 1
Creator                         : Adobe Illustrator CC 2014 (Macintosh)

EXIF Metadata provided by EXIF.tools