Janam Technologies P30M60W JANAM XP30W User Manual Eng QSG 4reg indd

Janam Technologies LLC JANAM XP30W Eng QSG 4reg indd

Contents

users manual

XP Series Quick Start Guide™
Janam TechnologiesThe contents of this guide are confi dential.Copyright 2006 Janam Technologies LLC. All rights reserved.XP Series Quick Start GuideJanam Technologies LLC assumes no responsibility for any damage or loss resulting from the use of this guide. Janam Technologies LLC assumes no responsibility for any loss or claims by third parties which may arise through the use of this product. Janam Technologies LLC assumes no responsibility for any damage or loss caused by deletion of data as a result of malfunction, dead battery or repairs. Be sure to make backup copies of all important data on other media to protect against data loss.Important: Please read the End User Software License Agreement with this product before using the accompanying software program(s). Using any part of the software indicates that you accept the terms of the End User Software License Agreement.XP Series, XP20, XP30, Janam and the Janam logo are trademarks of Janam Technologies LLC. Other product and brand names may be trademarks or registered trademarks of their respective owners.
XP Series Quick Start GuideTo help you get started with your XP Series mobile computer, this guide features:- Hardware Overview- Installing the Battery- Getting StartedFor additional product details visit www.janam.comFor Palm OS® software updates and information visit www.palmsource.comContent and Additional Resources
Janam TechnologiesHardware Overview1. Power2. Indicator LED3. LCD4. Connector5. Scan Trigger6. Right Trigger7. Left Trigger8. Navigation9. Home10. Enter11. Brightness/Contrast12. Programmable13. Function14. Backspace15. Alpha/Numeric Shift16. Space17. Shift 2345678989106471011121123PDA Keypad Numeric Keypad1312 1416171512
XP Series Quick Start GuideHardware Overview1. Battery Door2. Battery Screw3. Reset4. Microphone (XP30 Series)5a. Speaker (XP30 Series)5b. Buzzer (XP20 Series)6. IrDA Window7. Stylus8. Stylus Slot9. Lanyard Connector74235a/5b6891Battery Compartment
Janam TechnologiesInstalling the BatteryINSTALLING THE BATTERY1. To access the battery compartment, turn the battery-screw counterclockwise to open the latch and remove battery cover.2. Position the battery-lift strap, place the Lithium-ion battery and snap into place.3. Replace the battery cover by positioning the top prongs fi rst and sliding cover into place. Tighten battery-screw by turning clockwise.
XP Series Quick Start GuideGetting StartedCALIBRATING THE SCREENThe fi rst time the device is turned on, the Welcome Utility appears. To set up the device, follow the on-screen instructions using the stylus to tap the exact center of each targetNote - If your XP Series device came pre-loaded with a custom software application, the Welcome Utility may not appear.BRIGHTNESS/CONTRAST/BACKLIGHT ADJUSTMENTControl PDA Keypad Numeric KeypadBrightness(XP30 Series)Press the brightness/contrast control on the keypad. Use stylus to adjust brightness by sliding the on-screen control left/right. Press and hold the yellow function key and press left/right navigation keys. Use stylus to adjust brightness by sliding the on-screen control left/right.Contrast(XP20 Series)Press the brightness/contrast control on the keypad. Use stylus to adjust contrast by sliding the on-screen control left/right. Press and hold the yellow function key and press left/right navigation keys. Use stylus to adjust contrast by sliding the on-screen control left/right.Backlight On/Off Press and hold the power button to toggle backlight on/off.Press and hold the power button to toggle backlight on/off.
Janam Technologies The CE Mark on the product indicates that the system has been tested to and conforms with the provisions noted within the 89/336/EEC Electromagnetic Compatibility Directive and the 73/23/EEC Low Voltage Directive.For further information, please contact:Janam Technologies40 Goosehill RoadCold Spring Harbor, NY 11724Janam Technologies shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive.FCC and Canadian ComplianceXP Series mobile computers meet or exceed all applicable standards and have been manufactured to the highest level of quality. To see the specifi c labels associated with RF terminals confi gurations, visit www.janam.com.Warning: Changes or modifi cations to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.XP Series Batch TerminalRegulatory and Safety ApprovalsParameter Specifi cationU.S.A. FCC Part 15, Class BCanada ICES-003European Community EN55022:1998 (CISPR 22) Class B EN55024:1998 EN60950 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
XP Series Quick Start GuideThis Class B digital apparatus complies with the Canadian ICES-003.Cet appareil numerique de la Class B est conforme a la norm NMB-003 du Canada.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.L’utilisation de ce dispositif est autorisée seulement aux deux conditions suivantes : (1) il ne doit pas produire de brouil-lage, et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.XP Series RF Terminals with 802.11b and/or BluetoothRF, Regulatory and Safety ApprovalsParameter Specifi cationRF Approvals U.S.A. FCC Part 15.247Canada RSS 210This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Janam TechnologiesHowever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may fi nd the following booklet helpful: “Something about Interference.” This is available at FCC local regional offi ces. Our company is not responsible for any radio or television interference caused by unauthorized modifi cations of this equipment or the substitution or attachment of connective cables and equipment other than those specifi ed by our company. The correction is the responsibility of the user. Use only shielded data cables with this system.This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmit-ter. To maintain compliance with the FCC RF exposure guidelines for body-worn operation, do not use accessories that contain metallic components other than specifi ed by the manufacturer.This Class B digital apparatus complies with the Canadian ICES-003.Cet appareil numerique de la Class B est conforme a la norm NMB-003 du Canada.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.L’utilisation de ce dispositif est autorisée seulement aux deux conditions suivantes : (1) il ne doit pas produire de brouil-lage, et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from win-dows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
XP Series Quick Start GuideRF, Regulatory and Safety ApprovalsParameter Specifi cationR&TTE EN 300 328:2004 EN 301 489-17:2000 EN 60950-1:2001 EN 50371:2001This product is marked with in accordance with the Class II product requirements specifi ed in the R&TTE Directive, 1005/5/EC. The equipment is intended for use throughout the European Community. Its authorization for use in France is restricted as follows.PAN European Frequency Range: 2.402-2.480 GHzRestrictions in France: Indoor use – Maximum power (EIRP*) of 100 mW for the 2400-2483.5 MHz. Outdoor use – Maximum power (EIRP*) of 100 mW for the 2400-2454 MHz band and maxi-mum power (EIRP*) of 10 mW for the 2454-2483 MHz band.Pacemakers, Hearing Aids and Other Electrically Powered DevicesMost manufacturers of medical devices adhere to the IEC 601-1-2 standard. This standard requires devices to operate properly in an EM Field with strength of 3V/m over a frequency range of 26 to 1000MHz.The maximum allowable fi eld strength emitted by the XP Series is 0.3V/m according to Subpart B of Part 1 of the FCC rules. Therefore, the XP Series has no effect on medical devices that meet the IEC specifi cation.Microwaves. The radio in the XP Series terminal operates on the same frequency band as a microwave oven. Therefore, if you use a microwave within range of the XP Series you may notice performance degradation in your wireless network. However, both your microwave and your wireless network will continue to function. The XP Series Batch devices do not contain a radio, and therefore, are not affected by microwave ovens.
Janam TechnologiesCare and Cleaning of TerminalsWhen needed, clean the image engine window and the LCD display with a clean, non-abrasive, lint-free cloth. The terminal can be cleaned with a damp cloth.For European Community UsersJanam Technologies complies with Directive 2002/69/EC of THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 27 January 2003 on waste electrical and electronic equipment (WEEE).Waste Electrical and Electronic Equipment InformationThis product has required the extraction and use of natural resources for its production. It may contain hazardous substances that could impact health and the environment, if not properly disposed.In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems for product disposal. Those systems will reuse or recycle most of the materials of the product you are disposing in a sound way.The crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal waste and invites you to use the appropriate separate take-back systems for product disposal.If you need more information on the collection, reuse and recycling systems, please contact your local region waste administration. You may also contact your supplier for more information on the environmental performances of this product.

Navigation menu