Japan Radio Co NCR-333 Marine NAVTEX Receiver User Manual

Japan Radio Co Ltd. Marine NAVTEX Receiver

Instruction Manual

Download: Japan Radio Co NCR-333 Marine NAVTEX Receiver User Manual
Mirror Download [FCC.gov]Japan Radio Co NCR-333 Marine NAVTEX Receiver User Manual
Document ID571910
Application IDnXtvuCXCj8Shh2smsIa42w==
Document DescriptionInstruction Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize86.02kB (1075219 bits)
Date Submitted2005-08-16 00:00:00
Date Available2005-09-16 00:00:00
Creation Date2005-07-01 17:16:02
Producing SoftwareAcrobat Distiller 6.0 (Windows)
Document Lastmod2005-07-01 18:05:43
Document Titleuntitled

NAVTEX Receiver
NCR-333
Instruction Manual
7ZPJD0304
Preface
Thank you for purchasing NCR-333 NAVTEX Receiver.
The NAVTEX receiver automatically receives NAVTEX service broadcasts supplied in English
and other optional languages.
• Be sure to read this manual for full comprehension before using the equipment.
• Save this manual near at hand for quick reference in the future.
Make use of this manual when experiencing operation difficulties.
Before Operation
Concerning the symbols
This manual uses the following symbols to explain correct operation and to prevent
injury or damage to property.
The symbols and descriptions are as follows. Understand them before proceeding with
this manual.
WARNING
CAUTION
Indicates a warning that, if ignored, may
result in serious injury or even death.
Indicates a caution that, if ignored, may
result in injury or damage to property.
Examples of symbols
The △ symbol indicates caution (including DANGER and WARNING).
The illustration inside the △ symbol specifies the content of the caution
more accurately. (This example warns of possible electrical shock.)
The
symbol indicates that performing an action is prohibited.
The illustration inside the
symbol specifies the contents of the
prohibited operation. (In this example disassembly is prohibited.)
The ● symbol indicates operations that must be performed.
The illustration inside the ● symbol specifies obligatory instructions. (In
this example unplugging is the obligatory instruction.)
ii
Handling Precautions
WARNING
Do not disassemble or customize this unit.
electrical shock or malfunction.
Doing so may cause fire,
Do not get this equipment wet or spill any liquids on or near this equipment.
Doing so causes electrical shock or malfunction.
Do not use a voltage other than specified.
electrical shock or malfunction.
Doing so may cause fire,
Do not attempt to inspect or repair the inside of this equipment with the
exception of qualified service personnel, as doing so may cause fire, electric
shock or malfunction. If any malfunctions are detected, contact our service
center or agents.
iii
Handling Precautions
CAUTION
Do not use this equipment for anything other than specified.
Doing so may cause malfunction or damage to persons.
Do not adjust the trimmer resistors or the trimmer capacitors on the PCB
unit.
Doing so may cause malfunction or damage to persons. They are preset at
the factory.
Do not install this equipment in a place other than specified or in one with
excessive humidity, steam, dust or soot. Doing so may cause fire, electric
shock, malfunction or damage to persons.
Do not place this equipment anywhere vibration or impact is likely to occur.
Doing so may cause a fall or damage to property and persons.
Do not place any objects on this equipment.
Doing so may cause a fall, malfunction or damage to property and persons.
Leave installation of this equipment to our service center or agents.
Installation by an unauthorized person may lead to malfunction.
iv
External Views
NCR-333 NAVTEX Receiver
NAW-333 NAVTEX Antenna
NBG-319 Power Supply Unit
NBG-320 Power Supply Unit
vi
CONTENTS
Preface .................................................................................................................. i
Before Operation .................................................................................................. ii
Handling Precautions ........................................................................................... iii
External Views ...................................................................................................... v
1. GENERAL .....................................................................................................
1.1 Outlines ....................................................................................................
1.2 Features ...................................................................................................
1.3 Components .............................................................................................
1.3.1 Standard Components ..........................................................................
1.3.2 Options .................................................................................................
1.3.3 Configuration .........................................................................................
1.4 Outline .....................................................................................................
1-1
1-1
1-1
1-2
1-2
1-2
1-3
1-4
2. INSTALLATION DIAGRAM ............................................................................ 2-1
3. PART NAMES AND FUNCTIONS ................................................................. 3-1
3.1 NCR-333 NAVTEX Receiver .................................................................... 3-1
4. DISPLAYS .....................................................................................................
4.1 Displays ...................................................................................................
4.1.1 Message text screen .............................................................................
4.1.2 Message list 1 screen ...........................................................................
4.1.3 Message list 2 screen ...........................................................................
4.1.4 Save message list screen .....................................................................
4.1.5 Position/date screen .............................................................................
4.1.6 Setup screen .........................................................................................
4-1
4-1
4-1
4-2
4-2
4-3
4-3
4-4
5. INSTALLATION .............................................................................................
5.1 Installation ................................................................................................
5.1.1 Selection of location ..............................................................................
5.1.2 Mounting ...............................................................................................
5-1
5-1
5-1
5-1
6. OPERATION .................................................................................................. 6-1
6.1 Menu Tree ................................................................................................ 6-1
6.2 Basic Operation ....................................................................................... 6-2
6.2.1 Turning ON the power............................................................................. 6-2
6.2.1.1 Start up (Normal) ................................................................................ 6-2
6.2.1.2 Start up (Abnormal-1) ......................................................................... 6-3
6.2.1.3 Start up (Abnormal-2) ......................................................................... 6-3
6.2.1.4 Start up (Abnormal-3) ......................................................................... 6-4
6.2.2 Turning OFF the power........................................................................... 6-4
6.2.3 Backlight adjustment............................................................................... 6-5
6.2.4 Contrast adjustment .............................................................................. 6-5
6.2.5 Alarm ...................................................................................................... 6-6
6.2.6 Screen switching..................................................................................... 6-6
6.2.7 Displaying the message.......................................................................... 6-7
6.2.7.1 Message text ...................................................................................... 6-7
6.2.7.2 Message list 1 .................................................................................. 6-13
6.2.7.3 Message list 2 .................................................................................. 6-21
6.2.7.4 Save message list ............................................................................ 6-22
vii
6.3 MAIN MENU ..........................................................................................
6.3.1 RX STATION screen ...........................................................................
6.3.1.1 Receiving mode setting (RX MODE).................................................
6.3.1.2 Receiving channel setting (OPERATING FREQ.) .............................
6.3.1.3 Automatic receiving station selection (AUTO MODE SETTING) .......
6.3.1.4 Manual receiving station selection (MANUAL MODE SETTING) ......
6.3.2 Receiving message type settings (MESSAGE TYPE SETTING) .........
6.3.3 DISPLAY setting menu (DISPLAY SET) .............................................
6.3.3.1 Contrast adjustment (CONTRAST) .................................................
6.3.3.2 Brightness settings (DIMMER) ........................................................
6.3.3.3 Buzzer settings (BUZZER) ..............................................................
6.3.3.4 Time Difference setting (LOCAL TIME) ...........................................
6.3.3.5 Assigning to the USER key (USER KEY SETTING) .......................
6.3.3.6 POSITION/TIME screen settings (POS/TIME DISP.SET) ...............
6.3.4 NAVTEX setting menu (NAVTEX) ......................................................
6.3.4.1 Character size setting (CHARACTER SIZE) ...................................
6.3.4.2 CER setting (CER DISP.SETTING) .................................................
6.3.4.3 Automatic scrolling setting (MESSAGE SCROLL) ............................
6.3.4.4 Scrolling speed adjustment (MESSAGE SPEED) .............................
6.3.4.5 External printer settings (PRINTER PROPERTY) .............................
6.3.5 MAINTENANCE menu (MAINTENANCE)............................................
6.3.5.1 Self Diagnosis (SELF DIAGNOSIS) ..................................................
6.3.5.2 NAVTEX alarms (NAVTEX ALARM)..................................................
6.3.5.3 Setting status of the NAVTEX Receiver (STATUS) ...........................
6.3.5.4 Port monitor (PORT MONITOR)........................................................
6.3.5.5 Software version (SOFTWARE VERSION) .......................................
6.3.6 The display language setting (LANGUAGE) ........................................
6-24
6-25
6-26
6-26
6-27
6-31
6-32
6-33
6-34
6-34
6-34
6-35
6-36
6-37
6-38
6-39
6-39
6-40
6-40
6-41
6-42
6-43
6-46
6-48
6-49
6-52
6-52
7. MAINTENANCE AND INSPECTION .............................................................
7.1 General Maintenance and Inspection ......................................................
7.2 Periodic Inspection ..................................................................................
7.2.1 Confirming the Rx station and Message type ......................................
7.2.2 Confirming the Alarm Status...................................................................
7.3 Trouble Shootings .....................................................................................
7.3.1 Trouble Shootings ..................................................................................
7.3.2 Maintenance Units .................................................................................
7.3.3 Spear parts for periodic maintenance.....................................................
7-1
7-1
7-2
7-2
7-2
7-3
7-3
7-4
7-4
8. AFTER-SALES SERVICE ............................................................................. 8-1
Before returning repair .................................................................................. 8-1
Periodical maintenance recommended ......................................................... 8-1
9. SPECIFICATIONS ........................................................................................
9.1 General (NCR-333) .................................................................................
9.1.1 Receiver ...............................................................................................
9.1.2 Operation panel ....................................................................................
9.1.3 Power supply ........................................................................................
9.1.4 External interfaces ................................................................................
9.1.5 Environmental condition .......................................................................
9.1.6 Supported interface sentences .............................................................
9.1.7 Received message log .........................................................................
9.2 NAVTEX ANTENNA (NAW-333 - Option) ................................................
9.2.1 Electrical characteristics .......................................................................
9.2.2 Environmental condition .......................................................................
viii
9-1
9-1
9-1
9-1
9-1
9-1
9-2
9-2
9-2
9-3
9-3
9-3
9.3 POWER SUPPLY UNIT (NBG-320 - Option) ........................................... 9-3
9.4 POWER SUPPLY UNIT (NBG-319 - Option) ........................................... 9-3
ix
x
1.
1.1
GENERAL
Outlines
The NAVTEX NCR-333 function receives and displays the various types of information broadcast
at frequencies of 518 kHz, 490 kHz and 4209.5 kHz, such as: navigational warning,
meteorological warning, search and rescue information, and other types of information. NCR-333
also provides the function that selects information type and coast station for intended uses.
1.2
Features
● Receiving NAVTEX broadcasts
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
NCR-333 receives NAVTEX broadcasts automatically on 518 kHz, 490 kHz, and 4209.5 kHz.
● Large screen allows comfortable visibility
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
NCR-333 has a 5.7-inch LCD screen display with clear visibility.
It also provides three different character sizes of display, and can be selected at your
convenience.
● Message saving function
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
NCR-333 can store up to 200 message identification codes for 70 hours. Moreover, the stored
message of each channel can be saved up to 50 messages permanently.
● Automatically receiving station setting function
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
NCR-333 can select receiving stations automatically on GPS position data is valid.
● Permanent storage of data settings
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
NCR-333 can set and store the message type and seashore station that receive to internal
memory. The data, therefore, does not need to be re-set, even after power has been turned off.
● Dual voltage supply input
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
NCR-333 can be used on wither 24 VDC or 12 VDC vessels.
● Self-diagnosis Function
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
NCR-333 has automatic self-diagnosis function. This function allows easy maintenance and high
system reliability.
● Connection to external equipment
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
NCR-333 can be used with the JRC Total Navigator (ECDIS) and external serial printers.
1-1
1.3
Components
1.3.1 Standard Components
No.
Name
NAVTEX Receiver
Tapping screws
Instruction manual
Operation card
Antenna cable
Type
NCR-333
MPTG31659
7ZPJD0304
7ZPJD0306
7ZCJD0251
Quantity
Remarks
4 tapping screws
Present volume
0.5 m
Options
NAVTEX Antenna
Power supply unit
Power supply unit
External printer
Printer cable
Printer cable
Printer power cable
Type
NAW-333
NBG-319
NBG-320
DPU-414
7ZCJD0254
7ZCJD0270
7ZCJD0257B
Quantity
Printer connection kit
7ZXJD0076
10
11
Printer paper
NAVTEX buzzer
DMC
External buzzer
connection kit
6ZCAF00252A
CGC-300A
NCH-321A
7ZXJD0074
13
Data connection kit
7ZXJD0075
14
Console mount kit
MPBC39314
1.3.2 Options
No.
12
1-2
Remarks
Whip antenna for NCR-333
12 / 24VDC input
100/220VAC Manual Setting
D-sub 9-pin 1.5 m
D-sub 9-pin 10 m
1.5 m
7ZCJD0257B and
2-pin terminal block
112mm x φ50mm 25m x1
External buzzer
Distress Message Controller
1.5 m cable and
2-pin terminal block
1.5 m cable and
3-pin terminal block
1.3.3 Configuration
• System Block Diagram
NAW-333
NAVTEX ANTENNA
(OPTION)
NCR-333
NAVTEX RECEIVER
DPU-414
PRINTER
(OPTION)
NBG-320
POWER SUPPLY
(OPTION)
DC +12V
DC +6.5V
NBG-319
POWER SUPPLY
(OPTION)
AC 110/220V
DC +12/24V
1-3
1.4
Outline
• Outline Drawing of NCR-333 NAVTEX Receiver
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
Unit: mm
Mass: approx. 2.1 kg
1-4
• Outline Drawing of NAW-333 NAVTEX Antenna
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
Unit: mm
Mass: approx. 0.3 kg
1-5
15±0.7
70±0.5
• Outline Drawing of NBG-319 Power Supply Unit
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
6±0.5
1.5
1.5
Unit: mm
Mass: approx. 0.9 kg
20±0.7
70±0.5
• Outline Drawing of NBG-320 Power Supply Unit
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
6±0.5
1.5
1.5
Unit: mm
Mass: approx. 3.3 kg
1-6
• Outline Drawing of DPU-414 Printer
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
Unit: mm
Mass: approx. 0.7 kg
1-7
1-8
NAW-333
NAVTEX ANTENNA
MF/HF RADIO EQUIPMENTS
Connector: N-P-10U
(JRC Supply)
*1 x 2 x 0.75mm (JIS TTYCS-1)
*1 x 2 x 0.75mm 2 (JIS TTYCS-1)
*1 x 2 x 0.75mm 2 (JIS TTYCS-1)
7ZCJD0251
(Cable Length = 0.5m)
Note1: * marked cables are supplied by dock yard
Note2:
marked components are optional
INS / ECDIS (IEC61162-1)
INS / (D)GPS RECEIVER (IEC61162-1)
BELOW DECK
ABOVE DECK
*RG-10UY
50m max.
Connector: N-P-10U
(JRC Supply)
RG-58A/U
0.42m Typ.
+ANT
-ANT
+BK
-BK
RX-A
RX-B
GND-ISO
TX-A
TX-B
GND-ISO
DC+
DC GND
*2 x 1.5mm2 (JIS DPYC-1.5)
13
31
DC12/24V
OUT
DC6.5V
OUT
DC12V
OUT
GND
DC12/24V
IN
DC24V IN
AC IN
NBG-320
POWER SUPPLY
DC6.5V
OUT
GND
J502
NBG-319
POWER SUPPLY
31
J2
EXT ALM
J3
DISP
CMN-2333
RX UNIT
J1
DATA OUT2
DATA Connection KIT
NAVTEX
ANTENNA
J153
DATA Connection KIT
TX-A
TX-B
GND-ISO
7ZXJD0075
(Cable Length = 1.5m)
TX-A
TX-B
GND-ISO
7ZXJD0075
(Cable Length = 1.5m)
EXT ALM+
EXT ALM-
50ohm
J152
PRINTER / MAINTENANCE
*2 x 1.5mm2 (JIS DPYC-1.5)
*2 x 1.5mm2 (JIS DPYC-1.5)
*2 x 1.5mm2 (JIS DPYC-1.5)
*2 x 1.5mm2 (JIS DPYC-1.5)
*1 x 2 x 0.75mm 2 (JIS TTYCS-1)
*1 x 2 x 0.75mm 2 (JIS TTYCS-1)
*2 x 1.5mm2 (JIS DPYC-1.5)
*2 x 1.5mm2 (JIS DPYC-1.5)
* POWER SOURCE
DC+12/24V
GND
EXT ALMEXT ALM+
EXT ALM+
EXT ALM-
CGC-300A
NAVTEX
BUZZER
NCH-321A
DMC
TB10
27 DAL
28 S-GND
29 DAL
30 DAL +
Maximum cable length between
NBG-319/320 and DPU-414 is 10m
DPU-414
PRINTER
EMERGENCY
POWER SOURCE
DC+24V
EMERGENCY
POWER SOURCE
AC110/220V
EMERGENCY
POWER SOURCE
DC+12/24V
REMOTE MAINTENANCE
SERVER
EMERGENCY
POWER SOURCE
DC+12/24V
MULTI PURPOSE DISPLAY
Printer Connection KIT
7ZXJD0076
(Cable Length = 1.5m)
7ZCJD0257B: Cable only
(Cable Length = 1.5m)
7ZCJD0254
(Cable Length = 1.5m)
or
7ZCJD0270
(Cable Length = 10m)
2.
COAXIAL CABLE
AND CONNECTOR
(ATTACHMENT)
WLH-30/0/18-U-5
(ATTACHMENT)
Hi-Z
J151
7ZXJD0074
(Cable Length = 1.5m)
EXT ALM Connection KIT
NCR-333
NAVTEX RECEIVER
Notes:
INSTALLATION DIAGRAM
CAUTION
Leave installation of this system to our service center or agents.
Installation by an unauthorized person may result in malfunction.
2-1
2-2
3. PART NAMES AND FUNCTIONS
3.1
NCR-333 NAVTEX Receiver
● Front view
LCD Panel
For further information, refer to “● Display indicators” and “4. DISPLAY”.
A: Key Panel
USER Key
Displays the screen assigned to this key.
Refer to "6.3.3.5 USER KEY" about the
setting of USER key.
MENU Key
Displays the “Main Menu”.
DISP Key
Changes the screen, refer to “4. DISPLAY”.
Up, Down, Left, Right Key
Moves the cursor, scrolls the display
screen, and selects the item.
Buzzer
CLR Key
Clears input errors or cancel operations.
Turns off the buzzer sound.
ENTER Key
Determines selection of an item and fixes
a setup.
＊ Key
DIMMER Key
Displays the small window.
Adjusts the back light brightness of the
LCD.
POWER/CONTRAST Key
Power Off
Turns the power off with pressing the
PWR/CONT key and the DIM key at the
same time.
Turns the power ON. Adjusts the contrast
of the LCD while power is turned on.
3-1
● Rear view
Protective cover
To connect the antenna cable and the power cable, remove this cover.
External equipments connector
ECDIS, external buzzer, and MPD (Multi purpose display) cables are connected to the connector.
Printer/Maintenance connector
Serial printer and Maintenance PC cables are connected to the connector.
3-2
● Rear panel (Terminal)
―
Terminal Number and Name
ANT +
ANT
ANT 3
BK +
BK
BK 5
RXA
RXB
DATA IN
GND ISO
TXA
DATA OUT
10
11
TXB
GND ISO
12
12/24V
DC IN
13
GND
―
―
Description
Connect an antenna cable.
Connect the key lines leading from the
transmitter.
Connect the INS / External GPS cable for serial
communication.
Connect the isolated signal ground cable for
serial communication.
Connect the INS cable for serial communication
with INS.
Connect the isolated signal ground cable for
serial communication.
Connect the power supply cable.
The voltage range of the power supply between
10.8 and 35.0 VDC.
This terminal is for electrical grounding to the
vessel.
3-3
● Display indicators
ⅤⅢ
Station selection mode
NAVAREA No.
The NAVAREA number is displayed with
position data input.
: "AUTO MODE" is selected for coast station
selection.
: "MANUAL MODE" is selected for coast station
selection.
SORT
Displays the sorting order of the message list.
Refer to “6.2.7.2 Message list 1”.
Display title
The title of the current screen
Save message
This message has been saved.
Unread message
Unread message is stored.
Check mark
Refer to ”6.2.7.2 Message list 1”.
Arrow mark
‘▲’ ‘▼’marks are displayed on the top/ bottom
line when the display screen is able to scroll
upward/downward.
Status bar
Displays alarm, received message
type and other status
MSG LIST
SORT:MSG TYPE
ⅤⅢ
ID
FREQ LINES
DATE
TIME
IA01 4209.5
15 04/06/09 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10 04/06/09 10:34
STATION : KUSIRO
MSG TYPE: NAVIGATIONAL WARNINGS
IA07
490
20 04/06/09 09:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KC10
490
12 04/06/09 05:34
STATION : KUSIRO
MSG TYPE: ICE REPORTS
KH13
518
5 04/06/09 05:34
STATION : KUSIRO
MSG TYPE: LORAN MESSAGE
KP16
518
9 04/06/09 01:34
STATION : KUSIRO
DATA:321/342
Receiving message
The channel number is displayed while receiving message on the channel.
: 518kHz
: 490kHz
: 4209.5kHz
NAVTEX Alarm
‘ALR’ is displayed while NAVTEX alarm has occurred.
Refer to “6.3.5.2 NAVTEX alarm”.
SAR message
When a search and rescue (SAR) message is received
with the buzzer sound.
Alarm message
When an alarm message (MSG TYP: A,B,L) is received
with the buzzer sound.
Unread message
Unread messages exist.
GPS position data
"GPS" is displayed while external GPS position data has input.
3-4
4. DISPLAYS
4.1 Displays
Each time the DISP key is pressed, the screen is switched in the order below:
Message text -> Message list 1 -> Message list 2 -> Save message list -> Position/date -> ...
After NCR-333 is started, a message text screen is displayed.
4.1.1 Message text screen
Message text screen displays the text of the received message.
This screen is displayed after NCR-333 is turned on, or after receiving a message.
Title Bar
The following items are displayed.
ID: ID number of the message text
FREQ: Received channel frequency
LINES: The total line of the message text
DATE: Received date （DD/MM/YY）
TIME: Received time (UTC)
IA01 4209.5
18 31/10/06 12:34
123400 UTC JUNE 04
JAPAN NAVTEX N.W. NR 1260/2004
KEIHIN KO, TOKYO WEST PASSAGE.
DAYTIME DAILY UNTIL 28 JUNE 2004
AREA BOUNDED BY
35-35-37.9N 139-47-18.4E
35-34-58.9N 139-48-08.6E
35-34-53.9N 139-48-03.1E
35-35-02.0N 139-47-55.3E
35-35-32.3N 139-47-16.6E
35-35-35.0N 139-47-15.1E
35-33-37.9N 139-46-18.4E
35-33-58.9N 139-46-16.6E
35-33-32.3N 139-45-16.6E
35-35-35.0N 139-44-15.1E, WGS-84
LINE: 10/ 18
Cursor position
LINE: 10 / 18
(a)
(b)
(a) Cursor line position
(b) Total line
Scroll Bar
The cursor position on the message
text is indicated.
4-1
4.1.2 Message list 1 screen
Message list 1 screen displays the list of the stored messages.
This screen is displayed by indicating ID, FREQ, LINES, DATE (DD/MM/YY), TIME, STATION and
Message Type of each message.
Move the cursor up/down to select the message, and press the ENT key to display the message
text.
MSG LIST 1 SORT:MSG TYPE
ⅤⅢ
ID
FREQ LINES
DATE
TIME
IA01 4209.5
15 04/06/09 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10 04/06/09 10:34
STATION : KUSIRO
MSG TYPE: NAVIGATIONAL WARNINGS
IA07
490
20 04/06/09 09:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KC10
490
12 04/06/09 05:34
STATION : KUSIRO
MSG TYPE: ICE REPORTS
KH13
518
5 04/06/09 05:34
STATION : KUSIRO
MSG TYPE: LORAN MESSAGE
DATA:321/600
Cursor position
DATA: 321 / 600
(a) (b)
(a) Cursor data position
(b) Total data
Scroll bar
The cursor position on the total
message data is indicated.
4.1.3 Message list 2 screen
The message list 2 displays more message indexes than the message list 1, by indicating only ID,
FREQ, LINES, DATE (DD/MM/YY), and TIME of each message.
Move the cursor up/down to select the message, and press the ENT key to display the message
text.
MSG LIST 2 SORT:MSG TYPE
ID
FREQ LINES
DATE
IA01 4209.5
15 09/06/04
IB02 490
20 09/06/04
IC03 4209.5
12 09/06/04
ID04 518
5 09/06/04
IE05 518
30 09/06/04
IF06 518
12 09/06/04
IG07 490
15 09/06/04
IH08 490
11 09/06/04
II09 4209.5
10 09/06/04
KJ10 490
20 09/06/04
KK11 518
20 04/06/04
KL12 518
14 03/06/04
KH13 518
10 02/06/04
KN14 518
7 01/06/04
KO15 518
12 28/05/04
DATA:321/600
4-2
ⅤⅢ
TIME
12:34
11:34
10:34
10:34
10:34
09:34
09:34
09:34
09:34
05:34
05:34
05:34
05:34
05:34
01:34
4.1.4 Save message list screen
Save message list screen displays the list of the saved messages.
This screen is displayed by indicating ID, FREQ, LINES, DATE (DD/MM/YY), TIME, STATION and
Message Type of each message.
Move the cursor up/down to select the message, and press the ENT key to display the saved
message text.
SAVE MSG
SORT:MSG TYPE
ⅤⅢ
ID
FREQ LINES
DATE
TIME
IA01 4209.5
15 04/06/09 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10 04/06/09 10:34
STATION : KUSIRO
MSG TYPE: NAVIGATIONAL WARNINGS
IA07
490
20 04/06/09 09:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KC10
490
12 04/06/09 05:34
STATION : KUSIRO
MSG TYPE: ICE REPORTS
KH13
518
5 04/06/09 05:34
STATION : KUSIRO
MSG TYPE: LORAN MESSAGE
DATA: 21/ 93
4.1.5 Position/date screen
Position/date screen displays time, position, navigational data (SOG, COG, HDG, and ROT) when
GPS data is valid.
These parameters are not displayed when no GPS data.
POS/TIME
Position
SORT:MSG TYPE
ⅤⅢ
89°59.999’N
179°59.999’E
TIME 23:59(UTC)
DATE 31/12/04
(DD/MM/YY)
Date / time
SOG: 102.2KT
COG: 359.9°
Navigational
HDT: 359.9°
data
ROT:+127.1°/MIN
4-3
4.1.6 Setup screen
To display “Main menu”, press the MENU key.
Refer to “6.3 MAIN MENU” for NCR-333 settings
MAIN MENU
1.RX STATION_
2.MESSAGE TYPE
3.DISPLAY
4.NAVTEX
5.MAINTENANCE
6.LANGUAGE: ENGLISH
[EXIT]
4-4
ⅤⅢ
5. INSTALLATION
5.1 Installation
5.1.1 Selection of location
The NAVTEX NCR-333 is designed so that it can be installed on either a desk, a wall, or the ceiling of the
vessel. Select an installation location that satisfies the criteria listed on the followings.
WARNING
The installation location should be free from direct sunlight.
The length of the grounding wire should be minimized.
The installation location should also be: free from excessive heat, moisture, and vibration; in
case of installation on the ceiling, free from the stagnant heat as well as the above, and; in case
of installation near a window, free from salt water spray as well as the above.
The distance from the magnetic compass should be at least 1 meter.
The antenna cable, power cable, and grounding wire should be routed so as not to be in close
proximity with transmitter, radar, and other sources of electronic noise, as well as the cables of
these external units.
5.1.2 Mounting
Mount the NCR-333 on a table top, a bulkhead, or a ceiling by using the mounting base. Opening the case
is not necessary for mounting.
And keep a clearance for the maintenance (refer to figure below).
The mounting procedure is as follows;
- Loose the two knobs to remove the mounting base.
- Mount the mounting base on the selected location.
- Install the case on the mounting base by securing the two knobs.
4 -φ6.5
MOUNTING BASE (BOTTOM VIEW)
Wall
CLEARANCE
(Unit: mm)
Space required for receiver installation
5-1
5-2
6.
OPERATION
6.1 Menu Tree
[DSPL] Key
POS/TIME
[ENT
SAVE MSG LIST
MSG LIST 2
MSG LIST 1
[DSPL] key
(Power ON)
MSG VIEW
[MENU]
], [ENT] Key
], [ENT] Key
], [ENT] Key
], [ENT] Key
], [CLR] Key
], [CLR] Key
], [CLR] Key
], [CLR] Key
[CLR]
[MENU]
[MENU] Key
MAIN MENU
1. RX STATION
1. RX MODE
2. OPERATING FREQ.
3. AUTO MODE SETTING
4. MANUAL MODE SETTING
2. MESSAGE TYPE
1. MSG TYPE
3. DISPLAY
1. CONTRAST
2. DIMMER
- MAXIMUM
- TYPICAL
- MINIMUM
3. BUZZER
- ALARM MSG
- RECEIVED MSG
- NAVTEX ALARM
- CLICK
4. LOCAL TIME
5. USER KEY SETTING
6. POS/TIME DISP. SET
1. STATION (AUTO)
1. STATION (MANUAL)
1. USER KEY
4. NAVTEX
1. CHARACTER SIZE
2. CER DISP.SETTING
3. MESSAGE SCROLL
4. MESSAGE SPEED
5. PRINTER PROPERTY
- DATA OUT
- DATA FORMAT
- BAUDRATE
- FLOW CONTROL
- PRINT DIRECTION
5. MAINTENANCE
1. SELF DIAGNOSIS
1. SELF DIAGNOSIS
2. LCD DIAGNOSIS
3. SELF DIAGNOSIS LOG
2. NAVTEX ALARM
1. ALARM HISTORY
3. STATUS
1. STATUS
4. PORT MONITOR
1. PORT SELECTION
2. PORT LOG
1. MONITOR screen
1. LOG screen
5. SOFTWARE VERSION
- PROGRAM
- LANGUAGE
- OPTION
6. LANGUAGE
6-1
6.2 Basic Operation
6.2.1 Turning ON the power
Holding down the PWR/CONT key turns on the power, the starting screen appears, and then the
self-diagnosis screen appears for 15 seconds later. After diagnosis is finished, message text screen appears.
Caution
Check the main power supply of a switchboard, and a cable connection of NCR-333 NAVTEX
Receiver when the power cannot be turned on.
* SELF-DIAGNOSING...
* NOW LOADING...
ROM CHECK: OK
NCR-333
RAM CHECK: OK
NAVTEX RECEIVER
ANT CHECK: OK
VERSION 1.00
LOOP TEST:
- PRESS ‘CLR’ KEY TO EXIT -
Starting screen
Self-diagnosis screen
Note
Self diagnosis can be canceled when the CLR key is pressed. A message text screen is displayed.
6.2.1.1 Start up (Normal)
When all the results of self-diagnosis are 'OK', the result screen is displayed for about 5 seconds. And then
the result screen changes to the latest message test screen automatically.
* SELF-DIAGNOSING...
ROM CHECK: OK
RAM CHECK: OK
ANT CHECK: OK
LOOP TEST:
- PRESS ‘CLR’ KEY TO EXIT -
Self-diagnosis screen
6-2
5 sec.
later
IA01 4209.5
15
04/06/09 12:34
123400 UTC JUNE 04
JAPAN NAVTEX N.W. NR 1260/2004
KEIHIN KO, TOKYO WEST PASSAGE.
DAYTIME DAILY UNTIL 28 JUNE 2004
AREA BOUNDED BY
35-35-37.9N 139-47-18.4E
35-34-58.9N 139-48-08.6E
35-34-53.9N 139-48-03.1E
35-35-02.0N 139-47-55.3E
35-35-32.3N 139-47-16.6E
35-35-35.0N 139-47-15.1E
35-33-37.9N 139-46-18.4E
35-33-58.9N 139-46-16.6E
35-33-32.3N 139-45-16.6E
35-35-35.0N 139-44-15.1E, WGS-84
LINE: 10/ 18
The latest message text screen
6.2.1.2 Start up (Abnormal-1)
When any result of self-diagnosis is “NG”, a message text screen does not change automatically. And the
caution sentence as shown in the following figure is displayed on the self-diagnostic screen. In this case,
press the CLR key. The latest message text screen appears.
Caution
When “NG” is in a result, be sure to carry out self diagnosis in the “MAIN MENU” after displaying the
message text screen. Check the detailed result of the “NG” item. (Refer to “6.3.5.1 Self diagnosis”)
* SELF-DIAGNOSING...
ROM CHECK: OK
RAM CHECK: OK
ANT CHECK: OK
LOOP TEST: NG
PLEASE CARRY OUT ‘SELF-DIAGNOSIS’
IN MAINTENANCE MENU.
[PRESS ‘CLR’ KEY]
6.2.1.3 Start up (Abnormal-2)
When the result of “ROM CHECK” is “NG”, the sub screen may be displayed as shown in the following
figure.
Be sure to select "[START]" on the sub screen. In this case, although NCR-333 operates, the screen cannot
display in languages other than English.
[START]: The latest message text screen is displayed.
[INST]:
The software installation screen is displayed.
When the installation screen is displayed, press and hold the PWR/CONT and DIM keys simultaneously until
the power is turned off. Turn on the power, and restart the NCR-333.
Caution
Contact our service center or agents.
* SELF-DIAGNOSING...
ROM CHECK: NG
*LANGUAGE DAT.ERR*
RAM CHECK: OK
STARTING NAVTEX?
OR
ANT
CHECK: OK
RE-INSTALL
[START] [INST]
LOOP TEST: OK
[Option language data error]
PLEASE CARRY OUT ‘SELF-DIAGNOSIS’
*OPTION DAT.ERR*
IN MAINTENANCE MENU.
[PRESS ‘CLR’ KEY]
STARTING NAVTEX?
OR
RE-INSTALL
[START] [INST]
6-3
6.2.1.4 Start up (Abnorma-3)
When the following screen is displayed, press and hold the PWR/CONT and DIM keys simultaneously until
the power is turned off.
Caution
Contact our service center or agents.
_ CHECK SUM
COMPARING ERROR !
_ PLEASE RE-INSTALL
THE PROGRAM.
PLEASE RESTART AFTER
SOFTWARE UPDATE
PRESS AND HOLD [DIM]+[PWR]
6.2.2 Turning OFF the power
Press and hold the PWR/CONT and DIM keys simultaneously for one second until the power is turned off.
DIM
6-4
PWR
CONT
6.2.3 Backlight adjustment
Brightness of display can be adjusted in 4 levels.
The display is medium-intensity brightness at starting.
To change the britness, press the DIM key.
Maximum -> Medium -> Minimum -> Turn off the light -> Maximum ->...
DIM
Notes
PWR
CONT
The brightness becomes the brightest in the following case;
- Failure alarm is occurred. (“NAVTEX ALARM” screen appears.)
- After reception of “Navigational warnings” message (Message type “A”)
- After reception of “Meteorological warnings” message (Message type “B”))
- After reception of “Search and rescue information, and pirate attack warnings” (Message type
“D”)
- After reception of “Navigational warnings (Additional to letter “A”)” message (Message type “L”)
6.2.4 Contrast adjustment
Contrast of view area can be adjusted in 13 levels.
To change the contrast, press the PWR/CONT key. Contrast of View area is changed each time the
PWR/CONT key is pressed.
DIM
PWR
CONT
6-5
6.2.5 Alarm
To stop the buzzer sound, press the CLR key. Similarly, to stop the external buzzer sound (option:
CGC-300A), press the CLR key.
An alarm buzzer beeps in the following case;
- Failure alarm is occurred. (“NAVTEX ALARM” screen appears.)
- After reception of “Search and rescue information, and pirate attack warnings” (Message type “D”)
- After reception of “Navigational warnings” message (Message type “A”)
- After reception of “Meteorological warnings” message (Message type “B”))
- After reception of “Navigational warnings (Additional to letter “A”)” message (Message type “L”)
- After reception of other messages
Refer to “6.3.3.3 Buzzer settings” for a setup of alarm buzzer.
6.2.6 Screen switching
To change the display screen, press the DISP key.
DISP
DISP
DISP
DISP
DISP
6-6
6.2.7 Displaying the message
6.2.7.1 Message text
After starting this equipment, the latest message text screen is displayed.
Additionally, the latest message text screen is displayed just after reception of message while opening any
screen.
IA01
518
15
31/12/05 18:20
JAPAN NAVTEX N.W. NR 1260/2005
KEIHIN KO, TOKYO EAST PASSAGE.
DAYTIME DAILY UNTIL 08 JULY 2006
AREA BOUDED BY
35-35-37.9N 139-47-18.4E
35-34-58.9N 139-48-08.6E
35-34-53.9N 139-48-03.1E
35-35-02.0N 139-47-55.3E
35-35-32.3N 139-47-16.6E
35-35-35.0N 139-47-15.1E
35-33-37.9N 139-46-18.4E
35-33-58.9N 139-46-16.6E
35-33-32.3 N 139-45-16.6E
35-35-35.0N 139-44-15.1E, WGS-84
LINE: 10/ 18
The number on the left side of DATA shows the line number of
the present cursor position. The right side number shows the
total number of lines.
(Character size: Normal)
IA01 4209.5
18 31/12/05 18:20
JAPAN NAVTEX N.W. NR 1260/2005
KEIHIN KO, TOKYO EAST PASSAGE.
DAYTIME DAILY UNTIL 08 JULY 2006
AREA BOUDED BY
35-35-37.9N 139-47-18.4E
35-34-58.9N 139-48-08.6E
35-34-53.9N 139-48-03.1E
35-35-02.0N 139-47-55.3E
35-35-32.3N 139-47-16.6E
35-35-35.0N 139-47-15.1E
35-33-37.9N 139-46-18.4E
35-33-58.9N 139-46-16.6E
LINE: 13/ 18
(Character size: Medium)
IA01 4.2 31/12/05
JAPAN NAVTEX N.W.
NR 1260/2005
KEIHIN KO, TOKYO
EAST PASSAGE.
DAYTIME DAILY
UNTIL 08 JULY 2006
AREA BOUDED BY
35-35-37.9N 139-47
-18.4E
L:
9/ 18
(Character size: Large)
Fig.6-1 Message text screen
Notes
The number of lines of the message text screen is changed as follows;
- Character size “Normal”:
The message text of 16 lines is displayed at the maximum.
- Character size “Medium”: The message text of 13 lines
- Character size “Large”:
The message text of 10 lines
Refer to “6.3.4.1 Character size setting” about change of character size.
6-7
The message type and the message identification codes are as follows.
The message identification codes displayed on upper-left side of the message text screen (“lA01” in the
above example) indicates the message type.
These codes consist of four alpha-numeric characters which denote the coast station originating the
message, the message type and the report number.
a. First character
The coast station that has transmitted the message is assigned by a character from A to Z.
b. Second character
This charactger identifies the type of message.
[A]
Navigational warnings
[B]
Meteorological warnings
[C]
Ice reports
[D]
Search and rescue information, and pirate attack warnings
[E]
Meteorological forecasts
[F]
Pilot service messages
[G]
AIS
[H]
LORAN-C messages
[J]
SATNAV messages
[K]
Other electronic navaid messages
[L]
Navigational warnings (Additional to letter “A”)
[V - Y] Special services
[Z]
QRU (No messages on hand)
c. Third and fourth characters
These characters denote the report number assigned to the message by the coast station where the
message originated.
The four-character identification code is stored in memory only when the message is received at a
character error rate (CER) of 33 % or less. When an incoming message has the same identification code
as one already stored message at CER of 4 % or less in memory (about 70 hours), it will not be displayed
and stored. The above, however, does not apply to report number ‘00’. For report number ‘00’, the
code is not held in memory and messages are displayed and stored each time they are received.
a. Clear the unread mark
The message text is displayed after the message has been received.
Unread mark on the status bar shows unread messages has been received.
Procedures
1) If the ENT key is pressed, the caution sentence
disappears, and this message changes to read
message. If all messages are read messages, the “ ”
mark of status bar is cleared.
Notes
- Unread messages can also be checked on the
message list 1 or 2.
(Refer to “6.2.7.2” or “6.2.7.3”)
Be sure to clear the unread mark after reading a
message.
6-8
IA01
518
15
31/12/05 18:20
JAPAN NAVTEX N.W. NR 1260/2005
KEIHIN KO, TOKYO EAST PASSAGE.
DAYTIME DAILY UNTIL 08 JULY 2006
AREA BOUDED BY
35-35-37.9N 139-47-18.4E
35-34-58.9N 139-48-08.6E
35-34-53.9N 139-48-03.1E
35-35-02.0N 139-47-55.3E
35-35-32.3N 139-47-16.6E
35-35-35.0N 139-47-15.1E
35-33-37.9N 139-46-18.4E
35-33-58.9N 139-46-16.6E
35-33-32.3 N 139-45-16.6E
35-35-35.0N 139-44-15.1E, WGS-84
THE MSG WAS RECEIVED. PRESS[ENT]KEY
LINE: 10/ 18
Caution sentence
Unread mark
b. Read the message
Screen scrolling 1
The ‘ ‘ (‘ ‘) mark is displayed when the message text
scroll downward (upward) is available.
Procedures
1) To move the cursor up/down to the next line, press
the ▲ ▼ key. (Cursor scrolls one by one in the
message text.)
2) To scroll the next page of the message text
downward (upward) when cursor is on the bottom
(top) line, press the ▼ (▲) key.
IA01
518
15
31/12/05 18:20
JAPAN NAVTEX N.W. NR 1260/2005
KEIHIN KO, TOKYO EAST PASSAGE.
DAYTIME DAILY UNTIL 08 JULY 2006
AREA BOUDED BY
35-35-37.9N 139-47-18.4E
35-34-58.9N 139-48-08.6E
35-34-53.9N 139-48-03.1E
35-35-02.0N 139-47-55.3E
35-35-32.3N 139-47-16.6E
35-35-35.0N 139-47-15.1E
35-33-37.9N 139-46-18.4E
35-33-58.9N 139-46-16.6E
35-33-32.3 N 139-45-16.6E
35-35-35.0N 139-44-15.1E, WGS-84
LINE: 10/ 18
Screen scrolling 2
To skip to the next / previous message text screen is available.
Procedures
1) To display to the previous / next screen, press the
key.
c. Read the other message
Read the new message
The new message can be displayed on the message
text screen.
Procedures
1) Press the * key. The sub screen appears.
2) Select the “[NEXT MSG]”, and press the ENT key.
3) The new message is displayed.
Notes
IA01
518
15
31/12/05 18:20
JAPAN NAVTEX N.W. NR 1260/2005
KEIHIN KO, TOKYO EAST PASSAGE.
DAYTIME DAILY UNTIL 08 JULY 2006
AREA BOUDED BY
* SET139-47-18.4E
UP *
35-35-37.9N
MSG]
35-34-58.9N [NEXT
139-48-08.6E
MSG]
35-34-53.9N [PREV.
139-48-03.1E
MSG]
35-35-02.0N [SAVE
139-47-55.3E
OUT]
35-35-32.3N [PRINT
139-47-16.6E
DATA
OUT
35-35-35.0N 139-47-15.1E
35-33-37.9N 139-46-18.4E
35-33-58.9N 139-46-16.6E
35-33-32.3 N 139-45-16.6E
35-35-35.0N 139-44-15.1E, WGS-84
LINE: 10/ 18
- “[NEXT MSG]” can be selected when there is new message.
Read the old message
The old message can be displayed on the message text screen.
Procedures
1) Press the * key. The sub screen appears.
2) Select the “[PREV. MSG]”, and press the ENT key.
3) The old message is displayed.
Notes
- “[PREV.MSG]” can be selected when there is old message.
6-9
d. Save the message
Save the message
The currently open message can be saved.
The saved message is permanently stored in the data
memory.
Procedures
1) Press the * key. The sub screen appears.
2) Select the “[SAVE MSG]”, and press the ENT key.
3) “ARE YOU SURE?” is displayed. Select the “[OK]”,
and press the ENT key. (“NOW SAVING...” is
displayes on the sub screen.)
To return to the sub screen (SET UP), select
“[CANCEL]” and press the ENT key.
4) After message saving has been completed, press
the ENT key or the CLR key.
IA01
518
15
31/12/05 18:20
JAPAN NAVTEX N.W. NR 1260/2005
KEIHIN KO, TOKYO EAST PASSAGE.
DAYTIME DAILY UNTIL 08 JULY 2006
AREA BOUDED BY
* SET139-47-18.4E
UP *
35-35-37.9N
MSG]
35-34-58.9N [NEXT
139-48-08.6E
MSG]
35-34-53.9N [PREV.
139-48-03.1E
MSG]
35-35-02.0N [SAVE
139-47-55.3E
OUT]
35-35-32.3N [PRINT
139-47-16.6E
DATA
OUT
35-35-35.0N 139-47-15.1E
35-33-37.9N 139-46-18.4E
35-33-58.9N 139-46-16.6E
35-33-32.3 N 139-45-16.6E
35-35-35.0N 139-44-15.1E, WGS-84
*SAVE MSG*
LINE: 10/ 18
ARE YOU SURE?
[OK]
[CANCEL]
*SAVE MSG*
SAVE OK
[OK]
[CANCEL]
Notes
- The message that is not saved (the stored message) is automatically erased from the data memory
about 70 hours after receiving.
- 50 messages of an average length of 500 characters can be saved in each channel.
The message cannot be saved
When the saved message in the data memory is full, the
sub screen is displayed as shown in the following figure,
and the status bar shows which channel cannot be
saved (
mark).
Refer to “c. Put a check mark” (6.2.7.2 Message list 1)
for explanation of the display of the status bar.
Save again after deleting the message in save message
list when unable to save a message.
6-10
IA01
518
15
31/12/05 18:20
JAPAN NAVTEX N.W. NR 1260/2005
KEIHIN KO, TOKYO EAST PASSAGE.
DAYTIME DAILY UNTIL 08 JULY 2006
AREA BOUDED BY
35-35-37.9N
139-47-18.4E
*SAVE
MSG*
35-34-58.9N
TO 139-48-08.6E
ADD A NEW MSG,
35-34-53.9N
139-48-03.1E
DELETE A MSG
35-35-02.0N
IN 139-47-55.3E
THE SAVE LIST.
35-35-32.3N 139-47-16.6E
35-35-35.0N
139-47-15.1E
[OK]
35-33-37.9N 139-46-18.4E
35-33-58.9N 139-46-16.6E
35-33-32.3 N 139-45-16.6E
35-35-35.0N 139-44-15.1E, WGS-84
LINE: 10/ 18
RX1--OV
e. Print the message
Print the message
The currently open message can be printed when
having connected the external printer.
Procedures
1) Press the * key. The sub screen appears.
2) Select the “[PRINT OUT]”, and press the ENT key.
3) “ARE YOU SURE?” is displayed. Select the “[OK]”,
and press the ENT key. (“NOW PRINTING...” is
displayed on the sub screen.)
To return to the sub screen (SET UP), select
“[CANCEL]” and press the ENT key.
IA01
518
15
31/12/05 18:20
JAPAN NAVTEX N.W. NR 1260/2005
KEIHIN KO, TOKYO EAST PASSAGE.
DAYTIME DAILY UNTIL 08 JULY 2006
AREA BOUDED BY
* SET139-47-18.4E
UP *
35-35-37.9N
MSG]
35-34-58.9N [NEXT
139-48-08.6E
MSG]
35-34-53.9N [PREV.
139-48-03.1E
MSG]
35-35-02.0N [SAVE
139-47-55.3E
OUT]
35-35-32.3N [PRINT
139-47-16.6E
DATA
OUT
35-35-35.0N 139-47-15.1E
35-33-37.9N 139-46-18.4E
35-33-58.9N 139-46-16.6E
35-33-32.3 N 139-45-16.6E
35-35-35.0N 139-44-15.1E, WGS-84
*PRINT OUT*
LINE: 10/ 18
ARE YOU SURE?
[OK]
4) After message printing has been completed, press
the ENT key or the CLR key.
[CANCEL]
*PRINT OUT*
PRINT OUT OK
[OK]
[CANCEL]
Notes
- To stop printing, press the CLR key while printing.
- "[PRINT OUT]" cannot be selected when "DATA OUT" of "PRINTER PROPERTY" has set up "OFF".
Refer to “6.3.4.5 External printer settings”.
The message cannot be printed
When printing is unable, the sub screen is displayed as
shown in the following figure.
In this case, check the followings;
- The connection between the external printer
and NCR-333.
- “PRINTER PROPERTY” settings. (Refer
to “6.3.4.5 External printer settings”)
- Confirm the external printer. (Paper out, etc...)
IA01
518
15
31/12/05 18:20
JAPAN NAVTEX N.W. NR 1260/2005
KEIHIN KO, TOKYO EAST PASSAGE.
DAYTIME DAILY UNTIL 08 JULY 2006
AREA BOUDED BY
35-35-37.9N
139-47-18.4E
* PRINTER
ERROR *
35-34-58.9N
139-48-08.6E
PLEASE
CHECK THE
35-34-53.9N
139-48-03.1E
“ PRINTER
35-35-02.0N 139-47-55.3E
PROPERTY ”
35-35-32.3N
139-47-16.6E
SETTING.
35-35-35.0N
139-47-15.1E
[OK]
35-33-37.9N 139-46-18.4E
35-33-58.9N 139-46-16.6E
35-33-32.3 N 139-45-16.6E
35-35-35.0N 139-44-15.1E, WGS-84
LINE: 10/ 18
6-11
f. Output the message from an external port
The data of currently open message text can be output
with connection the external equipment (ECDIS, MPD).
Procedures
1) Press the * key. The sub screen appears.
2) Select the “[DATA OUT]”, and press the ENT key.
3) Select the port which outputs message data.
- SEL-DATA OUT: The message data is outputted
from a "DATA OUT" port.
- SEL- DISP OUT: The message data is outputted
from a "DISP" port.
IA01
518
15
31/12/05 18:20
JAPAN NAVTEX N.W. NR 1260/2005
KEIHIN KO, TOKYO EAST PASSAGE.
DAYTIME DAILY UNTIL 08 JULY 2006
AREA BOUDED BY
* SET139-47-18.4E
UP *
35-35-37.9N
MSG]
35-34-58.9N [NEXT
139-48-08.6E
MSG]
35-34-53.9N [PREV.
139-48-03.1E
MSG]
35-35-02.0N [SAVE
139-47-55.3E
OUT]
35-35-32.3N [PRINT
139-47-16.6E
DATA
OUT
35-35-35.0N 139-47-15.1E
35-33-37.9N 139-46-18.4E
35-33-58.9N 139-46-16.6E
35-33-32.3 N 139-45-16.6E
35-35-35.0N 139-44-15.1E, WGS-84
*DATA OUT*
[SEL-ECDIS OUT]
LINE: 10/ 18
[SEL-DISP
OUT]
4) “ARE YOU SURE?” is displayed. Select the “[OK]”,
and press the ENT key. (“NOW OUTPUTTING...” is
displayed on the sub screen.)
To return to the sub screen (SET UP), select
“[CANCEL]” and press the ENT key.
[CANCEL]
*DATA OUT*
ARE YOU SURE?
[OK]
[CANCEL]
5) After message outputting has been completed,
press the ENT key or the CLR key.
*DATA OUT*
DATA OUT OK
[OK]
Notes
- To stop outputting, press the CLR key while outputting.
6-12
[CANCEL]
6.2.7.2 Message list 1
Press the DISP key several times. The list of the currently stored messages appears.
This list shows a receiving station and a message type for each message.
MSG LIST1
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION : KUSIRO
MSG TYPE: NAVIGATIONAL WARNINGS
IA07
490
20
04/06/09 09:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KC10
490
12
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/04 05:34
STATION : KUSIRO
MSG TYPE: LORAN
MESSAGE
DATA:329/438
The number on the left side of DATA shows the
message number of the present cursor position. The
right side number shows the total number of messages.
(Character size: Normal)
MSG LIST1
SORT:DATE
Ⅵ
ID
FREQ LINES
DATE
TIME
IA01 4209.5
15 28/12/05 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10 28/12/05 12:33
STATION : KOSHIRO
MSG TYPE: NAVIGATIONAL WARNINGS
IA07
490
20 28/12/05 12:32
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KC10
490
12 27/12/05 18:30
STATION : KUSHIRO
MSG TYPE: ICE REPORTS
DATA:321/429
(Character size: Medium)
MSG LIST1
Ⅵ
ID
FREQ
DATE
IA01 4.2 28/12/05
STN:YOKOHAMA
MT :NAV WARNINGS
KA04 518 28/12/05
STN:KUSHIRO
MT :NAV WARNINGS
IA07 490 28/12/05
STN:YOKOHAMA
MT :NAV WARNINGS
D:321/429
(Character size: Large)
Fig.6-2 Message list 1
Notes
- "LINES" and "TIME" are not displayed when character size has selected "LARGE".
(Same applies to the message list 2 and a save message list)
6-13
a. Select a message
Screen scrolling 1
The ‘ ‘ (‘ ‘) mark is displayed when the message list 1
scroll downward (upward) is available.
Procedures
1) To meve the cursor up/down to the next line, press
the ▲ ▼ key. (Cursor scrolls one by one in the
message list 1.)
2) To scroll the next page of the message List 1
downward (upward) when cursor is on the bottom
(top) line, press the ▼ (▲) key.
MSG LIST1
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION : KUSIRO
MSG TYPE: NAVIGATIONAL WARNINGS
IA07
490
20
04/06/09 09:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KC10
490
12
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/04 05:34
STATION : KUSIRO
MSG TYPE: LORAN
MESSAGE
DATA:329/438
3) To read a message text, move the cursor to the
message and press the ENT key.
Screen scrolling 2
To skip to the next / previous message text screen is available.
Procedures
1) To display to the previous / next screen, press the
key.
Notes
Selecting "[PGUP]"or "[PGDN]" of the sub screen can also scroll the message list 1 screen similarly to
the above procedures. To display the sub screen, press the * key.
- [PGDN]: Previous screen
- [PGUP]: Next screen
6-14
b. Sort messages
To search message quickly, messages can be sorted.
Procedures
1) Press the * key. The sub screen appears.
2) Select the “LIST”, and press the ENT key.
The items of “LIST” appear.
3) The items of “LIST” are as follows;
SORT: The stored messages are displayed
- DATE: in the order of the date received in reverse
- STNS: in the order from the receiving station "A"
- AREA: in the order from the NAVAREA “I”
- MSGTYP: in the order from the message type “A”
- UNREAD: in the order of the date received in reverse
(unread messages)
MSG LIST1
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION
: KUSIRO
*SET
UP*
MSG TYPE: NAVIGATIONAL
WARNINGS
LIST_
IA07
490
20
04/06/09 09:34
[REVERSE]
STATION : [CHECK]
YOKOHAMA
MSG TYPE: NAVIGATIONAL
WARNINGS
SAVE MENU
KC10
490 PRINT
12 MENU
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/04 05:34
STATION : KUSIRO
MSG TYPE:
LORAN
MESSAGE
*LIST*
DATA:329/438
SORT:[DATE]
STNS
AREA
MSGTYP
UNREAD
DISP: The messages displayed on the selected channel.
- ALL: All the messages are displayed.
- 518KHZ: Only 518 kHz messages are displayed.
- 490KHZ: Only 490 kHz messages are displayed.
- 4209.5KHZ: Only 4209.5 kHz messages are displayed.
*LIST*
DISP:[ALL]
518KHZ
490KHZ
4209.5KHZ
[OK]
[CANCEL]
4) Select "SORT" item, and then select “DISP” item.
5) Select the [OK], and press the ENT key.
Sorting message starts.
6) After message sorting has been completed, press the ENT key
or the CLR key.
Rearrange the order of message conversely
Procedures
1) Press the * key. The sub screen appears.
2) Select the “REVERSE”, and press the ENT key.
3) The order of the message currently displayed is
rearranged conversely, and title of ‘SORT’ is
highlighted.
NOW SETTING...
[OK]
[CANCEL]
Highlight a title
MSG LIST1
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IB21 4209.5
15
12/05/05 11:10
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
IA33
518
10
13/05/05 22:34
STATION
: KUSIRO
*SET
UP*
MSG TYPE: NAVIGATIONAL
WARNINGS
LIST
KA67
490
20
04/06/09 02:15
[REVERSE]
STATION : [CHECK]
YOKOHAMA
MSG TYPE: NAVIGATIONAL
WARNINGS
SAVE MENU
PC01
490 PRINT
12 MENU
04/06/09 10:25
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
IA01 4209.5
15
09/06/04 12:34
STATION : KUSIRO
MSG TYPE: LORAN
MESSAGE
DATA:329/438
6-15
c. Put a check mark (Save/print/output more than one message at the same time)
Each checked message can be saved (printed or output)
MSG LIST1
SORT:DATE
at the same time.
Procedures
1) Press the * key. The sub screen appears.
2) Select the “[CHECK]”, and press the ENT key.
The sub screen is closed, and the message list 1
changes to the check screen.
The check screen highlights the "CHECK" on the
display title.
The number of check marks is displayed on the status
line.
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION
: KUSIRO
*SET
UP*
MSG TYPE: NAVIGATIONAL
WARNINGS
LIST_
IA07
490
20
04/06/09 09:34
[REVERSE]
STATION : [CHECK]
YOKOHAMA
MSG TYPE: NAVIGATIONAL
WARNINGS
SAVE MENU
KC10
490 PRINT
12 MENU
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/04 05:34
STATION : KUSIRO
MSG TYPE: LORAN
MESSAGE
DATA:329/438
Check screen
3) Select the message for checking, and press the ENT
key.
The “ “ is displayed on a line with cursor.
This mark means having checked the message.
4) Press the ENT key and put a check to other
messages.
In addition, when the following characters are
displayed,
KH13
518
09/06/04 05:34
CHECKING - PRESS [ENT] KEY
FINISHED - PRESS [*]
KEY
DATA:329/438
RX1--OV
It means that the checked number exceeded the
number which can be saved in the memory.
RX1--OV: The message of RX1 (518kHz) cannot
be saved any more to the memory.
RX2--OV: RX2 (490 kHz)
RX3--OV: RX3 (4209.5 kHz)
RX12-OV: RX1 and RX2
RX13-OV: RX1 and RX3
RX23-OV: RX2 and RX3
RX123OV: RX1, RX2 and RX3
In this case, messages still can be put a check,
however, the messages cannot be printed or data can
not be output.
5) Press the * key, to display the sub screen.
Select "SAVE MENU", "PRINT MENU", or "PORT
MENU" in the auxiliary screen.
To save, print or output messages at the same time,
refer to the procedure of d), e) and f).
If the CLR key is pressed on the sub screen, “EXIT
WITHOUT SETTING” is displayed in the sub screen. If
"O.K." is selected, the check marks are removed and
the display screen returns to the message list 1
screen.
CHECK
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION : KUSIRO
MSG TYPE: NAVIGATIONAL WARNINGS
IA07
490
20
04/06/09 09:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KC10
490
12
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/04 05:34
CHECKING - PRESS [ENT] KEY
FINISHED - PRESS [*]
KEY
DATA:329/438
Number of check marks
CHECK
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION : KUSIRO
MSG TYPE: NAVIGATIONAL WARNINGS
IA07
490
20
04/06/09 09:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KC10
490
12
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/04 05:34
CHECKING - PRESS [ENT] KEY
FINISHED - PRESS [*]
KEY
DATA:329/438
CHECK
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION
: KUSIRO
*SET
UP*
MSG TYPE: NAVIGATIONAL
WARNINGS
LIST
IA07
490
20
04/06/09 09:34
[REVERSE]
STATION : [CHECK]
YOKOHAMA
MSG TYPE: NAVIGATIONAL
WARNINGS
SAVE MENU
KC10
490 PRINT
12 MENU
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
*SET
KH13
518 UP* 5
09/06/04 05:34
EXIT
WITHOUT
CHECKING
- PRESS
[ENT] KEY
SETTING.
FINISHED - PRESS
[*]
KEY
ARE YOU
DATA:329/438
3 SURE?
[OK]
6-16
[CANCEL]
d. Save messages
Save one message
The selected message can be saved.
Procedures
1) Move cursor to the message to save.
2) Press the * key. The sub screen appears.
3) Select the “SAVE MENU”, and press the ENT key.
4) Select the “[SELECT MSG]” in the sub screen of
“SAVE MANU”.
Notes
- Select an item in the same procedure as “d. Save
the message - 3)” (p.6-10) after the above
procedure.
5) The “ “ mark on the saved message line shows the
message has saved completly.
Save messages at the same time
The messages which put the check mark can be saved at
the same time.
Procedures
1) Continued from Procedure 5) of "c. Put a check mark".
2) Select the “SAVE MENU”, and the ENT key.
3) Select the “[CHECK MSG]”, and the ENT key.
To clear to all check marks, select “[RESET CHECK]”
and press the ENT key.
Notes
- Select an item in the same procedure as “d. Save
the message - 3)” (p.6-10) after the above
procedure.
4)
The “ “ mark on the saved message line shows the
message has saved completly.
MSG LIST1
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION
: KUSIRO
*SET
UP*
MSG TYPE: NAVIGATIONAL
WARNINGS
LIST_
IA07
490
20
04/06/09 09:34
[REVERSE]
STATION : [CHECK]
YOKOHAMA
MSG TYPE: NAVIGATIONAL
WARNINGS
SAVE MENU
KC10
490 PRINT
12 MENU
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/04 05:34
STATION : KUSIRO
MSG TYPE:
LORAN
*SAVE
MENU*MESSAGE
DATA:329/438[SELECT MSG]
[CHECK
MSG]
[RESET CHECK]
[CANCEL]
To display to previous
screen, select “[CANCEL]”.
CHECK
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION
: KUSIRO
*SET
UP*
MSG TYPE: NAVIGATIONAL
WARNINGS
LIST
IA07
490
20
04/06/09 09:34
[REVERSE]
STATION : [CHECK]
YOKOHAMA
MSG TYPE: NAVIGATIONAL
WARNINGS
SAVE MENU
KC10
490 PRINT
12 MENU
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/04 05:34
CHECKING - PRESS
[ENT]
KEY
*SAVE
MENU*
FINISHED - PRESS [SELECT
[*]
KEY
MSG]
DATA:329/438
[CHECK
MSG]
[RESET CHECK]
[CANCEL]
MSG LIST1
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION : KUSIRO
MSG TYPE: NAVIGATIONAL WARNINGS
IA07
490
20
04/06/09 09:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KC10
490
12
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/04 05:34
STATION : KUSIRO
MSG TYPE: LORAN
MESSAGE
DATA:329/438
6-17
e. Print messages or the information on equipment
Print one message
The selected message can be printed.
Procedures
1) Move cursor onto the message to print.
2) Press the * key. The sub screen appears.
3) Select the “PRINT MENU”, and the ENT key.
4) Select the “[SELECT MSG]” in the sub screen of
“PRINT MENU”.
Notes
MSG LIST1
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION
: KUSIRO
*SET
UP*
MSG TYPE: NAVIGATIONAL
WARNINGS
LIST_
IA07
490
20
04/06/09 09:34
[REVERSE]
STATION : [CHECK]
YOKOHAMA
MSG TYPE: NAVIGATIONAL
WARNINGS
SAVE MENU
KC10
490 PRINT
12 MENU
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/04 05:34
STATION : KUSIRO
MSG TYPE:
LORAN
MESSAGE
*PRINT
MENU*
DATA:329/438[SELECT MSG]
[CHECK MSG]
[LIST]
[STATUS]
BATCH PRINT
- Select an item in the same procedure as “e. Print the
message - 3)” (p.6-11) after the above procedure.
Print messages at the same time
The messages which put the check mark can be printed at
the same time.
Procedures
1) Continued from Procedure 5) of "c. Put a check mark".
(The sub screen is displayed.)
2) Select the “PRINT MENU”, and the ENT key.
3) Select the “[CHECK MSG]”, and the ENT key.
To clear to all check marks, select “[RESET CHECK]”
and press the ENT key.
Notes
- Select an item in the same procedure as “e. Print the
message - 3)” (p.6-11) after the above procedure.
CHECK
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION
: KUSIRO
*SET
UP*
MSG TYPE: NAVIGATIONAL
WARNINGS
LIST
IA07
490
20
04/06/09 09:34
[REVERSE]
STATION : [CHECK]
YOKOHAMA
MSG TYPE: NAVIGATIONAL
WARNINGS
SAVE MENU
KC10
490 PRINT
12 MENU
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/04 05:34
CHECKING - PRESS [ENT] KEY
FINISHED
- PRESS
KEY
*PRINT
MENU*[*]
DATA:329/438[SELECT
MSG]
[CHECK MSG]
[LIST]
[STATUS]
BATCH PRINT
*PRINT MENU
[LIST]
[STATUS]
BATCH PRINT
[RESET CHECK]
[CANCEL]
To display to previous screen,
select “[CANCEL]”.
6-18
Print the information on equipment
The list of stored messages and the setting status can be printed.
Procedures
1) Press the * key. The sub screen appears.
*PRINT MENU*
[SELECT MSG]
[CHECK MSG]
[LIST]
[STATUS]
BATCH PRINT
2) Select the “[LIST]” or “[STATUS]”, and press the ENT key.
[LIST]:
The list of stored messages is printed.
[STATUS]: The setting status is printed. The contents of "6.3.5.3 Setting status of the NAVTEX
receiver" are printed.
3) Printing starts. After printing is completed, close the sub screen.
Print messages at the same time
The stored messages can be printed at the same time according to
type, station and channel.
Procedures
*PRINT MENU*
[SELECT MSG]
[CHECK MSG]
[LIST]
[STATUS]
BATCH PRINT
1) Press the * key. The sub screen appears.
2) Select the “BATCH PRINT”, and press the ENT key.
The sub screen of “BATCH PRINT MENU” appears.
*BATCH PRINT MENU*
[ALL STORED MSG]
3) Select the following message type for printing.
[ALL SAVE MSG]
The "SELECT MSG" can select the message printing by the
receiving channel, receiving station, message type.
*BATCH PRINT MENU*
-- SELECT MSG -[ALL STORED MSG]: All stored messages are printed.
CHANNEL:4209.5
[ALL SAVE MSG]:
All saved messages are printed.
STATION:A
MSG TYP:L
SELECT MSG:
The messages of the conditions
selected from the following three items are
printed.
- CHANNEL:
The receiving channel is selected from ‘518kHz’, ‘490kHz’, ‘4209.5kHz’ or ‘ALL’.
- STATION:
The receiving station is selected from 'A' to 'Z', or 'ALL'.
- MSG TYP:
The message type is selected from ‘A' to 'Z', or 'ALL'.
4) To start printing, select item and press the ENT key.
“ARE YOU SURE?” is displayed on the sub screen, if the ENT key is pressed after selecting “[ALL
STORED MSG]” or “[ALL SAVE MSG]”.
When in “SELECT MSG”, “ARE YOU SURE?” is displayed on the sub screen, if the ENT key is pressed
after selecting “MSG TYP”.
Notes
- Select an item in the same procedure as “e. Print the message - 3)” (p.6-10) after the above
procedure.
6-19
f. Output messages from an external port
Output one message
The external serial port output the selected message’s
data.
Procedures
1) Move cursor to the message to output.
2) Press the * key. The sub screen appears.
3) Select the “PORT MENU”, and the ENT key.
4) Select the “[SEL-DATA OUT]” or “[SEL-DISP OUT]” in
the sub screen of “PORT MENU”.
MSG LIST1
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION
: KUSIRO
*SET
UP*
MSG TYPE: [REVERSE]
NAVIGATIONAL WARNINGS
IA07
490
20
04/06/09 09:34
[CHECK]
STATION : YOKOHAMA
SAVE
MENU
MSG TYPE: NAVIGATIONAL
WARNINGS
PRINT MENU
KC10
490 PORT12 MENU
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/04 05:34
STATION : KUSIRO
MSG TYPE:
LORAN
*PORT
MENU*MESSAGE
DATA:329/438
[SEL-DATA OUT]
[SEL-DISP
OUT]
[CHK-DATA OUT]
[CHK-DISP
OUT]
[RESET CHECK]
Notes
- Select an item in the same procedure as “f. Output the message from an external port - 3)” (p.6-12)
after the above rocedure.
Output messages at the same time
The messages with the check mark can be output at the
same time.
Procedures
1) Continued from Procedure 5) of "c. Put a check mark".
(The sub screen is displayed.)
2) Select the “PORT MENU”, and the ENT key.
3) Select the “[CHK-DATA OUT]” or “CHK-DISP OUT”,
and the ENT key.
To clear to all check marks, select “[RESET CHECK]”
and press the ENT key.
- CHK-DATA OUT: Message data outgoing from
ECDIS or INS port.
- CHK-DISP OUT: Message data outgoing from DISP port.
CHECK
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION
: KUSIRO
*SET
UP*
MSG TYPE: [REVERSE]
NAVIGATIONAL WARNINGS
IA07
490
20
04/06/09 09:34
[CHECK]
STATION : YOKOHAMA
SAVE
MENU
MSG TYPE: NAVIGATIONAL
WARNINGS
PRINT MENU
KC10
490 PORT12 MENU
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/04 05:34
CHECKING - PRESS [ENT] KEY
FINISHED
- PRESS
KEY
*PORT
MENU* [*]
DATA:329/438
[SEL-DATA
OUT]
[SEL-DISP
OUT]
[CHK-DATA OUT]
[CHK-DISP
OUT]
[RESET CHECK]
Notes
- Select an item in the same procedure as “f. Output the message from an external port - 3)” (p.6-12)
after the above rocedure.
6-20
6.2.7.3 Message list 2
Press the DISP key several times. The list of the currently stored messages appears.
This list displays more messages on a screen than the message list 1 by not displaying “STATION” and
“MSG TYPE”.
MSG LIST2
SORT:DATE
ID
FREQ
LINES
DATE
IA01 4209.5
15
27/06/05
IB02
490
20
27/06/05
IC03 4209.5
10
27/06/05
ID04
518
27/06/05
IE05
518
30
27/06/05
IF06
518
12
27/06/05
IG07
490
15
27/06/05
IH08
490
11
27/06/05
II09 4209.5
10
27/06/05
KJ10
490
20
27/06/05
KK11
518
20
26/06/05
KL12
518
14
25/06/05
KH13
518
10
24/06/05
KN14
518
21/06/05
KO15
518
12
28/05/05
DATA:321/429
VI
TIME
12:34
11:34
10:34
10:34
10:34
09:34
09:34
09:34
09:34
05:34
05:34
05:34
05:34
05:34
01:34
(Character size: Normal)
MSG LIST2
SORT:DATE
ID
FREQ LINES
DATE
IA01 4209.5
15 27/06/05
IB02 490
20 27/06/05
IC03 4209.5
10 27/06/05
ID04 518
5 27/06/05
IE05 518
30 27/06/05
IF06 518
12 27/06/05
IG07 490
15 27/06/05
IH08 490
11 27/06/05
II09 4209.5
10 27/06/05
KJ10 490
20 27/06/05
KK11 518
20 26/06/05
KL12 518
14 25/06/05
DATA:321/429
(Character size: Medium)
Ⅵ
TIME
12:34
11:34
10:34
10:34
10:34
09:34
09:34
09:34
09:34
05:34
05:34
05:34
MSG LIST2
Ⅵ
ID
FREQ
DATE
IA01 4.2 27/06/05
IB02 490 27/06/05
IC03 4.2 27/06/05
ID04 518 27/06/05
IE05 518 27/06/05
IF06 518 27/06/05
IG07 490 27/06/05
IH08 490 27/06/05
II09 4.2 27/06/05
D:321/429
(Character size: Large)
Fig.6-3 Message list 2
Notes
- Selecting of each message, scrolling, saving, and the printing method are carried out in the same
procedure as the message list 1.
Refer to the operation procedure of the message list 1.
- The message list 2 does not display “ ” mark which shows the saved message. When you confirm
that the message was saved, display and check the message list 1 or the save message list.
6-21
6.2.7.4 Save message list
Press the DISP key several times. The list of the messages that is currently saved appears.
Only the list of messages saved by “Message list 1” or “Message list 2” is displayed.
SAVE MSG
SORT:DATE
Ⅵ
ID
FREQ LINES
DATE
TIME
IA01 4209.5
15 28/12/05 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10 28/12/05 12:33
STATION : KUSHIRO
MSG TYPE: NAVIGATIONAL WARNINGS
IA07
490
20 28/12/05 12:32
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KC10
490
12 27/12/05 18:30
STATION : KUSHIRO
MSG TYPE: ICE REPORTS
KH13
518
5 27/12/05 18:29
STATION : KUSHIRO
MSG TYPE: LORAN MESSAGE
DATA: 21/ 37
Notes
“
” mark is not
displayed on this
screen.
Fig.6-4 Save message list
- Selecting of each message, scrolling, saving, and the printing method are carried out in the same
procedure as the message list 1.
Refer to the operation procedure of the message list 1 about operation.
- The save message list does not display “ ” mark which shows the saved message.
6-22
a. Delete the saved message
If the message is deleted from the save message list, “ ” mark displayed on the message list 1 will also be
deleted.
Caution
The message is deleted after stored for 70 hours, and the message is deleted from the message list 1
and 2.
Delete one message
The selected message can be deleted.
Procedures
1) Move cursor onto the message to delete.
2) Press the * key. The sub screen appears.
3) Select the “DELETE MENU”, and press the ENT key.
4) Select the “[SELECT MSG]” in the sub screen of
“DELETE MANU”.
5) After message deleting has been completed, the
selected message is deleted from the save message
list and the “ “ mark is deleted from the message list
1.
In addition, the message is deleted after stored for 70
hours, and the message is deleted from the message
list 1 and 2.
Delete messages at the same time
The messages which put the check mark can be deleted at
the same time.
Procedures
1) Put check marks in the same procedure as "c.Put a
check mark" of "6.2.6.2 Message list 1."
2) Press the * key. The sub screen appears.
3) Select the “DELETE MENU”, and press the ENT key.
5) Select the “[CHECK MSG]”, and the ENT key.
4) If the ENT key is pressed after selecting “[RESET
CHECK]”, all check marks are cleared.
5) After message deleting has been completed, the
selected message has deleted from the save message
list and the “ “ mark is deleted from the message list
1.
The message is deleted after stored for 70 hours, and
the message is deleted from the message list 1 and 2.
SAVE MSG
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION
: KUSIRO
*SET
UP*
MSG TYPE: NAVIGATIONAL
WARNINGS
LIST_
IA07
490
20
04/06/09 09:34
[REVERSE]
STATION : [CHECK]
YOKOHAMA
MSG TYPE: NAVIGATIONAL
DELETE MENU WARNINGS
KC10
490 PRINT
12 MENU
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/04 05:34
STATION : KUSIRO
MSG TYPE:
LORANMENU*
MESSAGE
*DELETE
DATA: 21438 [SELECT MSG]
[CHECK
MSG]
[RESET CHECK]
[CANCEL]
To display to previous
screen, select “[CANCEL]”.
CHECK
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
IA01 4209.5
15
09/06/04 12:34
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
KA04
518
10
09/06/04 10:34
STATION
: KUSIRO
*SET
UP*
MSG TYPE: NAVIGATIONAL
WARNINGS
LIST
IA07
490
20
04/06/09 09:34
[REVERSE]
STATION : [CHECK]
YOKOHAMA
MSG TYPE: NAVIGATIONAL
DELETE MENU WARNINGS
KC10
490 PRINT
12 MENU
04/06/09 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/04 05:34
CHECKING - PRESS [ENT] KEY
FINISHED - PRESS [*]
KEY
DATA: 21/ 37
SAVE MSG
SORT:DATE
XI
ID
FREQ
LINES
DATE
TIME
KC10
490
12
09/06/05 05:34
STATION : YOKOHAMA
MSG TYPE: ICE REPORTS
KH13
518
09/06/05 05:34
STATION : KUSIRO
MSG TYPE: LORAN
MESSAGE
IA11
518
10
08/06/05 22:20
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
IA13
518
14
08/06/05 18:20
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
IA42
518
28
07/06/05 22:21
STATION : YOKOHAMA
MSG TYPE: NAVIGATIONAL WARNINGS
DATA: 18/ 34
6-23
6.3 MAIN MEMU
Main menu displays menu items for setting, and maintenance, etc.
To display the Main menu, press the MENU key during operation.
MAIN MENU
ⅤⅢ
1.RX STATION_
2.MESSAGE TYPE
3.DISPLAY
4.NAVTEX
5.MAINTENANCE
6.LANGUAGE: ENGLISH
[EXIT]
Fig.6-5 Main menu
Procedures
1. Press the ▲ ▼ key to select the menu item.
2. When the ENT key or the
key is pressed, the menu screen of selected item is displayed.
Notes
Previous screen is displayed when the CLR key is pressed. (Such as message text display or message
list 1, etc).
The outlines of menus are as follows;
1. RX STATION:
Displays the menu for selecting receiving stations (See 6.3.1)
2. MESSAGE TYPE:
Displays the menu for selecting message types (See 6.3.2)
3. DISPLAY:
Displays the menu for setting the display unit. (See 6.3.3)
4. NAVTEX:
Displays the menu for setting the NAVTEX receiver. (See 6.3.4)
5. MAINTENANCE:
Displays the maintenance menu. (See 6.3.5)
6. LANGUAGE:
Selects the menu display language. (See 6.3.6)
[EXIT]:
Return to the previous screen (Such as message text display or message list 1,
etc.)
6-24
6.3.1 RX STATION screen
To display RX STATION menu screen, select 1. RX STATION.
RX STATION
ⅤⅢ
1.RX MDOE: AUTO
2.OPERATING FREQ.:RX1/RX2/RX3
3.AUTO MODE SETTING
4.MANUAL MODE SETTING
Fig.6-6 RX STATION menu screen
Procedures
1. Press the ▲ ▼ key to select the menu item.
2. When ENT key or
key is pressed, the menu screen of selected item is displayed.
- When cursor is on the item 1 and 2, cursor moves to the right side of ":"
- When cursor is on the item 3 and 4, the menu screen of item 3 and 4 appears.
Notes
- To return to the MAIN MENU screen, press the CLR key or
key.
- If the
key is pressed when cursor is on the right side of ":" of item 1 and 2, cursor returns on the
item 1 and 2. (1.RX MODE, 2.OPERATING FREQ.)
The outlines of Menus are as follows;
1. RX MODE:
Select “AUTO” or “MANUAL” as the receiving station selection mothod.
(See 6.3.1.1)
2. OPERATING FREQ.:
Select receiving channels.
(See 6.3.1.2)
3. AUTO MODE SETTING:
Displays the menu screen by automatically selecting the receiving station
in each NAVAREA (Navigation area).
(See 6.3.1.3)
4. MANUAL MODE SETTING: Displays the menu screen for selecting the receiving station regardless of
NAVAREA.
(See 6.3.1.4)
6-25
6.3.1.1 Receiving mode setting (RX MODE)
The automatic select mode and the manual select mode for RX station :
- AUTO: Automatic select mode
When normal GPS position data is inputted, the position and NAVAREA of a ship are automatically
specified, and the message of the receiving station in the NAVAREA is received.
(The “ “ mark is displayed on the status bar.)
Notes
“AUTO” can be selected only when the GPS data is inputted.
- MANUAL: Manual select mode
Regardless of the NAVAREA, messages are received according to the station selection settings of
each channel.
Notes
The information of code number “00” is always received, displayed and stored automatically
regardless of the setting.
(Refer to “6.2.7.1 Message text”.)
6.3.1.2 Receiving channel setting (OPERATING FREQ.)
A receiving channel selection
Press the ▲ ▼ key and select the following items;
- RX1 (518 kHz)/ RX2 (490 kHz)/ RX3 (4209.5 kHz)
- RX1 / RX2
- RX1 / RX3
RX1 (518kHz) is always selected.
6-26
6.3.1.3 Automatic receiving station selection (AUTO MODE SETTING)
To display AUTO MODE SETTING screen, select 3.AUTO MODE SETTING from RX STATION menu (6.3.1).
Select the receiving station of each channel for every NAVAREA.
STATION(AUTO)
ⅩⅠ
NAVAREA :ⅩⅠ
FREQUENCY:RX1(518K)
SELECT ALL
A:JAYAPURA
N:GUANGZHOU
B:AMBON
O:FUZHOU
C:SINGAPORE
P:MEILUNG
D:MAKASSAR
Q:SHANGHAI
E:JAKARTA
R:DALIAN
F:BANGKOK RADIO
S:SANDAKAN
G:NAHA
T:MIRI
H:MOJI
U:PENANG
I:YOKOHAMA
V:CHUKPYON/GUAM
J:OTARU
W:PYONSAN
K:KUSHIRO/DANANG X:HO CHI MINH
L:HONG KONG
Y:
M:SANYA
Z:
Fig.6-7 The receiving station selection screen (Auto mode setting)
The items of the receiving station selection screen (auto mode) are as follows;
- NAVAREA:
Select the NAVAREA (I - XVI).
- FREQUENCY:
Select the channel (RX1 (518k), RX2 (490k), RX3 (4209.5k)).
SELECT ALL:
Select all the stations from A to Z.
: A message is received.
: A message is not received.
- Receiving station A – Z: Select receiving stations from A to Z
Notes
- When GPS data is inputted, the receiving station in your NAVAREA is automatically displayed in the
selection screen. Otherwise, the stations in NAVAREA1 are displayed first.
6-27
a. Select receiving stations
Select the receiving station of each channel for every NAVAREA.
All stations of initial setting are “A message is received: ”
Selection of NAVAREA
STATION(AUTO)
NAVAREA__:ⅠⅩ
FREQUENCY:RX1(518K)
SELECT ALL
A:BUSHEHR
B:HAMALA
C:
D:
E:
Procudure
1) Select NAVAREA, and press the ENT key.
Cursor moves to the right side of ":" (on a number).
ENT
2) Press the ▲ ▼ key and select the number of NAVAREA.
And then, press the ENT key.
The cursor moves to the lower line (on the “FREQUENCY”).
3) Select FREQUENCY, and press the ENT key.
Cursor moves to the right side of ":" (on the “RX1”).
STATION(AUTO)
NAVAREA
:ⅩⅠ
FREQUENCY:RX1(518K)
aa, aa
SELECT ALL
A:JAYAPURA
B:AMBON
C:SINGAPORE
D:MAKASSAR
E:JAKARTA
ENT
STATION(AUTO)
NAVAREA
:ⅩⅠ
FREQUENCY:RX1(518K)
SELECT ALL
A:JAYAPURA
B:AMBON
C:SINGAPORE
D:MAKASSAR
E:JAKARTA
4) Press the ▲ ▼ key and select a channel.
RX1 (518K): 518 kHz
RX2 (490K): 490 kHz
RX3 (4209.5K): 4209.5 kHz
5) Press the ▲ ▼
key to select a receiving station for setting.
- Pressing the ENT key switches alternately between “ “ and “ “.
- If the “SELSCT ALL” is “ ”, all station (A-Z) settings changes to “ ”.
STATION(AUTO)
NAVAREA
:ⅩⅠ
FREQUENCY:RX1(518K)
SELECT ALL
A:JAYAPURA
B:AMBON
C:SINGAPORE
D:MAKASSAR
E:JAKARTA
ENT
STATION(AUTO)
NAVAREA
:ⅩⅠ
FREQUENCY:RX1(518K)
SELECT ALL
A:JAYAPURA
B:AMBON
C:SINGAPORE
D:MAKASSAR
E:JAKARTA
(a) Selection of all stations
STATION(AUTO)
NAVAREA
:ⅩⅠ
FREQUENCY:RX1(518K)
SELECT ALL
A:JAYAPURA
B:AMBON
C:SINGAPORE
D:MAKASSAR
E:JAKARTA
ENT
STATION(AUTO)
NAVAREA
:ⅩⅠ
FREQUENCY:RX1(518K)
SELECT ALL
A:JAYAPURA
B:AMBON
C:SINGAPORE
D:MAKASSAR
E:JAKARTA
(b) Selection of each station
6-28
b. Cancel settings
When the CLR/ MENU/ DISP/ USER key is pressed while setting up “a. Select receiving stations”, the
information screen (the sub screen) as shown in the following figure is displayed.
Select “OK” or “CANCEL”.
OK:
Canceling the receiving station settings, the screen changes according to the pressed
key.
CANCEL: The information screen is closed. Continu the receiving station settings.
STATION(AUTO)
ⅩⅠ
NAVAREA
:ⅩⅠ
FREQUENCY:RX1(518K)
SELECT ALL
A:JAYAPURA
N:GUANGZHOU
B:AMBON
O:FUZHOU
*STNS(AUTO) P:MEILUNG
SET*
C:SINGAPORE
EXIT WITHOUT
D:MAKASSAR
Q:SHANGHAI
SAVING.
E:JAKARTA
R:DALIAN
F:BANGKOK
RADIO
S:SANDAKAN
ARE
YOU SURE?
G:NAHA (SAVE:PRESS’’*’’KEY)
T:MIRI
H:MOJI
U:PENANG
[OK]
[CANCEL]
I:YOKOHAMA
V:CHUKPYON/GUAM
J:OTARU
W:PYONSAN
K:KUSHIRO/DANANG
X:HO CHI MINH
L:HONG KONG
Y:
M:SANYA
Z:
c. Set up the next channel (or NAVAREA)
After a setup of a channel (or NAVAREA) finishes, the next channel (or NAVAREA) can be set up
continuously.
Procedures
1) Press the ▲ ▼
key for selecting FREQUENCY (or NAVAREA), and press the ENT key.
Cursor moves to the right side of ":"
2) Press the ▲ ▼ key and select the number of NAVAREA.
And then, press the ENT key.
3) Select a receiving station in the same procedures as “a. Select receiving stations”.
6-29
d. Save (or Clear) settings
Save (or clear) the settings on the sub screen after setting up.
Procedures
1) Press the * key. The sub screen appears.
Cursor is on the [CLEAR].
2) Press the ▼ key and select the following items.
3) Save settings
Select the [OK], and press the ENT key.
STATION(AUTO)
ⅩⅠ
NAVAREA
:ⅩⅠ
FREQUENCY:RX1(518K)
SELECT ALL
A:JAYAPURA
N:GUANGZHOU
B:AMBON
O:FUZHOU
*STNS(AUTO)P:MEILUNG
SET*
C:SINGAPORE
D:MAKASSAR
Q:SHANGHAI
SAVE CHANGES
TO
E:JAKARTA
R:DALIAN
THIS SETTING?
F:BANGKOK [CLEAR]
RADIO
S:SANDAKAN
G:NAHA
T:MIRI
[ALL CLEAR]
H:MOJI
U:PENANG
[OK]
[CANCEL]
I:YOKOHAMA
V:CHUKPYON/GUAM
J:OTARU
W:PYONSAN
K:KUSHIRO/DANANG
X:HO CHI MINH
L:HONG KONG
Y:
M:SANYA
Z:
Clear only settings of the screen that is currently open
Select the [CLEAR], and press the ENT key.
The receiving station settings of the screen that is currently open are restored to its former state, and the
cursor returns to NAVAREA.
Clear all settings
Select the [ALL CLEAR], and press the ENT key.
All the receiving station settings are restored to its former state, and the cursor returns to NAVAREA.
Continue setting up
Select the [CANCEL], and press the ENT key.
This sub screen is closed.
4) To start save precess, select [OK].
Then, “SAVE OK” is displayed on the sub screen.
Press the ENT or CLR key.
RX STATION menu screen appears.
*STNS(AUTO) SET*
SAVE CHANGES TO
THIS SETTING?
[CLEAR]
[ALL CLEAR]
[OK]
[CANCEL]
ENT
*STNS(AUTO) SET*
NOW SAVING...
[OK]
[CANCEL]
Saving is completed
*STNS(AUTO) SET*
SAVE OK
[OK]
6-30
[CANCEL]
6.3.1.4 Manual receiving station selection (MANUAL MODE SETTING)
To display MANUAL MODE SETTING screen, select 4.MANUAL MODE SETTING from RX STATION menu
(6.3.5).
Select the receiving station of each channel. There is no setup of NAVAREA.
STATION(MANUAL)
ⅩⅠ
FREQUENCY:RX1(518K)
SELECT ALL
A:
N:
B:
O:
C:
P:
D:
Q:
E:
R:
F:
S:
G:
T:
H:
U:
I:
V:
J:
W:
K:
X:
L:
Y:
M:
Z:
Fig.6-8 The receiving station selection screen (Manual mode setting)
The items of the receiving station selection screen (manual mode) are as follows;
- FREQUENCY:
Select the channel (RX1 (518k), RX2 (490k), RX3 (4209.5k)).
SELECT ALL:
Select all the stations from A to Z.
: A message is received.
: A message is not received.
- Receiving station A – Z: Select receiving stations from A to Z
Notes
When this screen is displayed, the receiving station of RX1 is displayed first.
a. Select receiving stations
Start with selection of "FREQUENCY".
Carry out the procedure from section 3) to 5) of p.6-28 “a. Select receiving stations”
b. Cancel settings
Carry out “b. Cancel settings” of p.6-29.
c. Set up the next channel (or NAVAREA)
Carry out the procedure from section 1) to 3) of p.6-29 “c. Set up the next channel (or NAVAREA)”.
d. Save (or Clear) settings
Carry out the procedure from section 1) to 4) of p.6-30 “d. Save (or Clear) settings”.
6-31
6.3.2 Receiving message type settings (MESSAGE TYPE SETTING)
To display MESSAGE TYPE SETTING menu screen, select 2. MESSAGE TYPE SETTING.
MSG TYPE
ⅩⅠ
FREQUENCY:RX1(518K)
SELECT ALL
A:NAV WARNINGS
N:[SPARE]
B:MET WARNINGS
O:[SPARE]
C:ICE REPORT
P:[SPARE]
D:SERCH & RESCUE Q:[SPARE]
E:MET FORECAST
R:[SPARE]
F:PILOT SERVICE
S:[SPARE]
G:DECCA
T:[SPARE]
H:LORAN
U:[SPARE]
I:[SPARE]
V:SPECIAL
J:SATNAV
W:SPECIAL
K:OTHER NAVAID
X:SPECIAL
L:NAV WARNINGS
Y:SPECIAL
M:[SPARE]
Z:NO MESSAGES
Fig.6-9 MESSAGE TYPE menu screen
The items of the receiving message type selection screen are as follows;
- FREQUENCY:
Select the channel (RX1 (518k), RX2 (490k), RX3 (4209.5k)).
SELECT ALL:
Select all the messages from A to Z.
: A message is received.
: A message is not received.
- Receiving message A – Z : Select receiving message from A to Z
Notes
Navigational warning [A], Meteorological warning [B], Search and rescue information/piracy and armed
robbery [D], Navigational warning (additional) [L] are obliged to receive a message. These message
types setting cannot be changed.
a. Select receiving message types
Start with selection of "FREQUENCY".
Carry out the procedure from section 3) to 5) of p.6-28 “a. Select receiving stations”.
b. Cancel settings
Carry out “b. Cancel settings” of p.6-29.
c. Save (ro Clear) settings
Carry out the procedure from section 1) to 4) of p.6-30 “d. Save (or Clear) settings”.
6-32
6.3.3 DISPLAY setting menu (DISPLAY SET)
To display DISPLAY SET menu screen, select 3.DISPLAY from MAIN MENU (6.3).
Display form, a buzzer, etc. can be set up on this screen.
DISPLAY SET
ⅩⅠ
1.CONTRAST
: 10
2.DIMMER
- MAXIMUM
: 10
- TYPICAL
: 6
- MINIMUM
: 2
3.BUZZER
: ON
- ALARM MSG
: ON
(FOR MESSAGE TYPE:A,B,L)
- RECEIVED MSG
: ON
- NAVTEX ALARM
: ON
- CLICK
: ON
4.LOCAL TIME
: ON
(TIME DIFFERENCE): -11:59
5.USER KEY SETTING
6.POS/TIME DISP.SET(1):POS
(2):TIME/NAV
Fig.6-10 DISPLAY SET menu screen
Procedures
1. Press the ▲ ▼ key to select the menu item.
2. When ENT key or
key is pressed, the menu screen of selected item is displayed.
- When cursor is on the item 1-4 and 6, cursor moves to the right side of ":"
- When cursor is on the item 5, the menu screen of item 5 appears.
Notes
- To return to the MAIN MENU screen, press the CLR key or
key.
- If the
key is pressed when cursor is on the right side of ":" of item 1-4 and 6, cursor returns on the
item 1-4 and 6. (1.CONTRAST, 2. DIMMER, ....)
The outlines of menus are as follows;
1. CONTRAST:
Adjust the contrast of this display.
2. DIMMER:
Set up the brightness level of this display.
3. BUZZER:
Select buzzer ON/OFF.
4. LOCAL TIME:
Input local time.
5. USER KEY SETTING: Assign the often used function for the USER key
6. POS/TIME DISP.SET: Set up the display of the POSITION/TIME screen.
(See 6.3.3.1)
(See 6.3.3.2)
(See 6.3.3.3)
(See 6.3.3.4)
(See 6.3.3.5)
(See 6.3.3.6)
6-33
6.3.3.1 Contrast adjustment (CONTRAST)
When 1. CONTRAST is selected, CONTRAST is ready to be entered. To adjust the contrast, press the ▲ ▼
key, and then press the ENT key.
1.CONTRAST
: 10
The adjustment of the contrast
- “1” is the darkest.
- “13” is the lightest.
The initial setting is “7”.
6.3.3.2 Brightness settings (DIMMER)
Brightness can be changed into four levels (Maximum, Typical, Minimum and off) by pressing the DIM key.
These brightness levels are set up in this item.
Select 2.DIMMER, and press the ENT key. Cursor moves to the right side of ":".
Number and brightness is changed when the ▲ ▼ key is pressed, and then press the ENT key.
Press the ENT key after setting up to "MINIMUM". All setting values are saved.
2.DIMMER
- MAXIMUM
- TYPICAL
- MINIMUM
: 10
: 8
: 4
Notes
“MAXIMUM” should enter the largest numerical value and “MINIMUM” should enter the smallest
numerical value.
6.3.3.3 Buzzer settings (BUZZER)
When 3. BUZZER is selected, each buzzer functions can be set enable (ON) or disable (OFF) as followings.
Press the ▲ ▼ key and select the “ON” or “OFF”.
Press the ENT key after setting up to "CLICK". All buzzer settings are saved.
3.BUZZER
: ON
- ALARM MSG
: ON
(FOR MESSAGE TYPE:A,B,L)
- RECEIVED MSG
: ON
- NAVTEX ALARM
: ON
- CLICK
: ON
BUZZER:
- ALARM MSG:
- RECEIVED MSG:
- NAVTEX ALARM:
- CLICK:
ON:
OFF:
A buzzer is sounded.
A buzzer is not sounded.
OFF: All buzzer functions are disabled.
ON: Each buzzer function as shown below can be enabled.
When a message (A, B and L) is received.
When a message (other than A, B and L) is received.
When a failure alarm occurs.
When a key is pressed.
Caution
When search and rescue message (D) is received, buzzer sounds. The SAR buzzer sound can not be
set to “OFF (disable)”.
6-34
6.3.3.4 Time Difference setting (LOCAL TIME)
"LOCAL TIME" can set up time difference to UTC.
When “ON” is selected, “(LOCAL)” is displayed in the POSITION/TIME screen. The time of the
POSITION/TIME screen displays the numerical value which added time difference to UTC.
When “OFF” is selected, “(UTC)” is displayed.
4.LOCAL TIME
: ON
(TIME DIFFERENCE): +09:00
Procudure
1.
Select 4.LOCAL TIME, and press the ENT key. Cursor moves to the right side of ":".
2.
Press the ▲ ▼ key and select the “ON” or “OFF”, and then press the ENT key.
The cursor moves to the lower line.
3.
Press the ▲ ▼ key and select “+ (add) “ or “- (sub)”. Next, input the numerical value within the range of
00:00 to 12:00. ( -12:00 to +12:00)
To save the "LOCAL TIME" settings, cursor should press the ENT key on the rightmost position
(minute).
Notes
The setup time difference is displayed on the POSITION/TIME screen.
6-35
6.3.3.5 Assigning to the USER key (USER KEY SETTING)
The USER key can be assigned to the often used function (screen).
Select 5. USER KEY SETTING, and press the ENT key. USER KEY SETTING screen appears.
USER KEY SETTING
ⅩⅠ
1.USER KEY: P
----------------------------------D:POSITION/TIME
E:RX STATION SETTING MENU
F:AUTO MODE SETTING
G:MANUAL MODE SETTING
H:MESSAGE TYPE SETTING MENU
I:DISPLAY SETTING MENU
J:USER KEY SETTING
K:NAVTEX SETTING MENU
L:MAINTENANCE MENU
M:SELF DIAGNOSIS
N:NAVTEX ALARM
O:STATUS
Fig.6-11 USER KEY SETTING screen
Press the ▲ ▼ key and select from “A” to “Z”, and then press the ENT key. “USER KEY” setting is saved.
“ “ mark is displayed on the bottom line when the USER KEY SETTING screen is able to scroll downward.
“ “ mark is displayed on the top line when the USER KEY SETTING screen is able to scroll upward.
To display DISPLAY menu screen, press the CLR.
Refer to the following table about selectable items;
Title
MESSAGE LIST1
MESSAGE LIST2
SAVE MESSAGE LIST
POSITION/ITME
RX STATION SETTING MENU
AUTO MODE SETTING
MANUAL MODE SETTING
MESSAGE TYPE SETTING MENU
DISPLAY SETTING MENU
USER KEY SETTING
NAVTEX SETTING MENU
MAINTENANCE MENU
SELF DIAGNOSIS
NAVTEX ALARM
STATUS
PORT MONITOR
PRINT
NON USE
6-36
Explanation
MESSAGE LIST 1 screen is displayed.
MESSAGE LIST 2 screen is displayed.
SAVE MESSAGE LIST screen is displayed.
POSITION/TIME screen is displayed.
RX STATION menu screen is displayed.
AUTO MODE SETTING screen (RX STATION menu) is
displayed.
MAMUAL MODE SETTING screen (RX STATION menu) is
displayed.
MESSAGE TYPE SETTING screen is displayed.
DISPLAY menu screen is displayed.
This screen (SER KEY SETTING) is displayed.
NAVTEX menu screen is displayed.
MAINTENANCE menu screen is displayed.
SELF DIAGNOSIS screen (MAINTENANCE menu) is displayed.
NAVTEX ALARM screen (MAINTENANCE menu) is displayed.
STATUS screen (MAINTENANCE menu) is displayed.
PORT MONITOR screen (MAINTENANCE menu) is displayed.
Printing is started if the USER key is pressed on the screen
which can print the external printer. Printing is stopped if the
CLR key is pressed during printing.
The USER key cannot be used.
6.3.3.6 POSITION/TIME screen settings (POS/TIME DISP.SET)
"POS/TIME DISP.SET" can set up the item displayed on the POSITION/TIME screen.
POSITION/TIME screen can be displayed selecting items of “position (POS)”, “time (TIME)”, and
“navigational information (NAV)”.
6.POS/TIME DISP.SET(1):POS
(2):TIME/NAV
Procudure
1. Select 6.POS/TIME DISP. SET(1), and press the ENT key. Cursor moves to the right side of ":".
2. Press the ▲ ▼ key and select the “POS”, “TIME” or “OFF”, and then press the ENT key.
This item is displayed on the upside of the POSITION/TIME screen.
Notes
The setup time difference is displayed on the POSITION/TIME screen.
When you have selected "OFF", cursor ends the setup of this item, without moving to the lower line “(2)”.
3. The cursor moves to the lower line “(2)”. Press the ▲ ▼ key, and then press the ENT key.
This item is displayed on the downside of the POSITION/TIME screen.
(1): POS, The selectable items of “(2)” are as follows.
OFF, TIME, TIME/NAV
(1): TIME, The selectable items of “(2)” are as follows.
OFF, POS, POS/TIME
- When “OFF” is selected, only the item of (1) is displayed on POSITION/TIME screen.
- When “TIME” (or “POS”) is selected, this item is displayed on the downside of the POSITION/TIME
screen.
- When “TIME/NAV” (or “POS/NAV”) is selected, time is displayed on the left side, and navigational
information is displayed on the right side of the POSITION/TIME screen.
Ex) The following figure is an example when selecting “POS” and “TIME/NAV”.
(1): POS
(2): TIME/NAV
POS/TIME
XI
The item of (1)
89°59.999’ N
139°59.999’ E
The item of (2)
TIME 23:59(UTC) SOG: 102.2KT
COG: 359.9°
DATA 31/12/05
HDT: 359.9°
(DD/MM/YY) ROT:+127.1°/MIN
6-37
6.3.4 NAVTEXsetting menu (NAVTEX)
To display NAVTEX SET menu screen, select 4.NAVTEX from MAIN MENU (6.3).
Character size, printer setting, etc. can be set up on this screen.
NAVTEX SET
1.CHARACTER SIZE
ⅩⅠ
: NORMAL
2.CER DISP.SETTING
: OFF
(CER:CHARACTER ERROR RATE)
3.MESSAGE SCROLL
: ON
4.MESSAGE SPEED
: FAST
5.PRINTER PROPERTY
- DATA OUT
- DATA FORMAT
- BAUDRATE
- FLOW CONTROL
- PRINT DIRECTION
MANUAL
ON
38.4KBPS
NONE
UPRIGHT
Fig.6-12 NAVTEX SET menu screen
Procedures
1. Press the ▲ ▼ key to select the menu item.
2. When ENT key or
key is pressed, the menu screen of selected item is displayed.
Notes
- To return to the MAIN MENU menu screen, press the CLR key or
key.
- If the
key is pressed when cursor is on the right side of ":", cursor returns on the item.
(1.CHARACTER SIZE, 2. CER DISP.SETTING, ....)
The outlines of menus are as follows;
1. CHARACTER SIZE:
Select the character size
2. CER DISP.SETTING: Add “CER” to the end of message
3. MESSAGE SCROLL: Set up the message scroll function
4. MESSAGE SPEED:
Select the scrolling speed
5. PRINTER PROPERTY: Set up the external printer connection
6-38
(See 6.3.4.1)
(See 6.3.4.2)
(See 6.3.4.3)
(See 6.3.4.4)
(See 6.3.4.5)
6.3.4.1 Character size setting (CHARACTER SIZE)
Displayed character can be changed into three sizes.
Select 1.CHARACTER SIZE, and press the ENT key. Cursor moves to the right side of ":".
Press the ▲ ▼ key, and then press the ENT key.
If the ENT key is pressed, the selected character size is saved, and the displayed character is changed.
1.CHARACTER SIZE
: NORMAL
The initial setting is “NORMAL”.
NORMAL:
The normal character size: 13x9 dots
MEDIUM:
The medium character size: 16x9 dots
LARGE:
The large character size: 20x16 dots
6.3.4.2 CER setting (CER DISP.SETTING)
A message text can add “CER(*1)“ to the end of message.
Select 2.CER DISP.SETTING, and press the ENT key. Cursor moves to the right side of ":".
Press the ▲ ▼ key and select the “ON” or “OFF”, and then press the ENT key. This setting is saved
2.CER DISP.SETTING : ON
(CER:CHARACTER ERROR RATE)
The initial setting is “OFF”.
ON: “CER” is displayed on the end of message.
OFF: “CER” is not displayed.
(*1)
: Character Error Rate
(When CER DISP.SETTING is set “ON”)
(When CER DISP.SETTING is set “OFF”)
IA01 4209.5
15
04/06/09 12:34
123400 UTC JUNE 04
JAPAN NAVTEX N.W. NR 1260/2004
KEIHIN KO, TOKYO WEST PASSAGE.
DAYTIME DAILY UNTIL 28 JUNE 2004
IA01 4209.5
15
04/06/09 12:34
123400 UTC JUNE 04
JAPAN NAVTEX N.W. NR 1260/2004
KEIHIN KO, TOKYO WEST PASSAGE.
DAYTIME DAILY UNTIL 28 JUNE 2004
35-35-02.0N 139-47-55.3E,WGS-84
(END OF MESSAGE
CER :
3.5%)
LINE: 18/ 18
35-35-02.0N 139-47-55.3E,WGS-84
(END OF MESSAGE)
LINE: 18/ 18
6-39
6.3.4.3 Automatic scrolling setting (MESSAGE SCROLL)
When character size has selected “LARGE”, a message text can be automatically scrolled on a screen.
Select 3.MESSAGE SCROLL, and press the ENT key. Cursor moves to the right side of ":".
Press the ▲ ▼ key and select the “ON” or “OFF”, and then press the ENT key. This setting is saved
3.MESSAGE SCROLL
: ON
The initial setting is “ON”
ON: A message text scroll.
OFF: A message text does not scroll.
6.3.4.4 Scrolling speed adjustment (MESSAGE SPEED)
The speed of automatic scrolling can be changed into three levels.
Select 4.MESSAGE SPEED, and press the ENT key. Cursor moves to the right side of ":".
Press the ▲ ▼ key and select the “ON” or “OFF”, and then press the ENT key. This setting is saved
4.MESSAGE SPEED
: NORMAL
The initial setting is “NORMAL”.
SLOW:
A character scrolls at the slowest speed.
NORMAL:
A character scrolls at the normal speed.
FAST:
A character scrolls at the fastest speed.
6-40
6.3.4.5 External printer settings (PRINTER PROPERTY)
Serial port (RS-232C: MAINTENANCE/PRINTER) conditions can be set up when connecting external printer.
Select 5.PRINTER PROPERTY, and press the ENT key. Cursor moves to the right side of ":".
After setting up to "FLOW CONTROL", press the ENT key. All settings are saved.
5.PRINTER PROPERTY
- DATA OUT
- DATA FORMAT
- BAUDRATE
- FLOW CONTROL
- PRINT DIRECTION
MANUAL
ON
4800BPS
NONE
UPRIGHT
The explanations of each item are as follows;
(1) DATA OUT
The data output method for printer is set up.
Press the ▲ ▼ key and select the following items. If the ENT key is pressed, Cursor moves to the lower line.
OFF:
The message is not outputted to the external printer.
AUTO:
After receiving a message, the data is automatically outputted to the external printer.
MANUAL:
The data of the selected message is outputted to the external printer.
(2) DATA FORMAT
The output data format is set up.
Press the ▲ ▼ key and select the following items. If the ENT key is pressed, Cursor moves to the lower line.
ON:
The header and footer are added to a message text.
OFF:
Only a message text is printed.
(The example of printing）
Header
---- 518kHz NAVTEX MESSAGE ---ZCZC IA01
TEST MESSAGE
NNNN
Footer
--- END OF MESSAGE CER = 0.0% --(3) BAUDRATE
Baudrate (bits/sec) is set up.
Press the ▲ ▼ key and select the following items. If the ENT key is pressed, Cursor moves to the lower line.
Baudrate can be selected from "4800", "9600", and "38.4K." BPS.
(4) FLOW CONTROL
The flow control is set up.
Press the ▲ ▼ key and select the following items. If the ENT key is pressed, Cursor moves to the lower line.
NONE:
The flow control is not performed.
HARD:
The flow control is performed.
(5) PRINT DIRECTION
Print direction is set up.
Press the ▲ ▼ key and select the following items. If the ENT key is pressed, all settings are saved.
UPRIGHT: Upright printing
INVERT:
Inverted printing
The initial settings are as follows. Set up as follows when DPU-414 is connected.
DATA OUT:
MANUAL
DATA FORMAT:
ON
BAUD RATE:
4800BPS
FLOW CONTROL:
NONE
PRINT DIRECTION:
UPRIGHT
6-41
6.3.5 MAINTENANCE menu (MAINTENANCE)
To display MAINTENANCE menu screen, select 5.MAINTENANCE from MAIN MENU (6.3).
Users can check current status of the system by the menu.
MANINTENANCE
ⅩⅠ
1.SELF DIAGNOSIS
2.NAVTEX ALARM
3.STATUS
4.PORT MONITOR
5.SOFTWARE VERSION
- PROGRAM : 12.34
- LANGUAGE: 21A
- OPTION : ---
Fig.6-13 MAINTENANCE menu screen
Procedures
1. Press the ▲ ▼ key to select the menu item.
2. When ENT key or
key is pressed, the menu screen of selected item is displayed.
- When cursor is on the item 1-4, cursor moves to the right side of ":"
- When cursor is on the item 5, the menu screen of item 5 appears.
Notes
- To return to the MAIN MENU screen, press the CLR key or
key.
- If the
key is pressed when cursor is on the right side of ":", cursor returns on the item.
(1.CHARACTER SIZE, 2. CER DISP.SETTING, ....)
The outlines of menus are as follows;
1. SELF DIAGNOSIS:
Perform self diagnosis test.
2. NAVTEX ALARM:
Display alarm logs for disorders.
3. STATUS:
Display current status of NAVTEX setting.
4. PORT MONITOR:
Display serial data of each port.
5. SOFTWARE VERSION:Display versions of software installed in NCR-333.
6-42
(See 6.3.4.1)
(See 6.3.4.2)
(See 6.3.4.3)
(See 6.3.4.4)
(See 6.3.4.5)
6.3.5.1 Self diagnosis (SELF DIAGNOSIS)
NCR-333 can be self-diagnosed.
Select 1.SELF DIAGNOSIS, and press the ENT key. SELF DIAGNOSIS screen appears.
SELF DIAGNOSIS
ⅩⅠ
1.SELF DIAGNOSIS
: START
ROM
: GOOD
RAM
: GOOD
SIO
: GOOD
PS
: GOOD
ANTENNA CHECK
: GOOD
518KHZ OVER ALL TEST
: GOOD
490KHZ OVER ALL TEST
: GOOD
4209.5KHZ OVER ALL TEST: GOOD
(THE QUICK BLOWN FOX JUMPS OVER
THE LAZY DOG.123456789,?/+-:’=)
2.LCD DIAGNOSIS
When character size has
selected “LARGE”, these
character strings are not
displayed.
:CANCEL
3.SELF DIAGNOSIS LOG
Fig.6-14 SELF DIAGNOSIS screen
Procudure
1. Press the ▲ ▼ key in order to select the item to diagnose.
2. When the ENT key is pressed, the menu screen of selected item appears.
Pressing the
key can display the same.
- When cursor is on the item 1 or 2, cursor moves to the right side of ":"
- When cursor is on the item 3, the menu screen of item 3 appears.
Notes
- To return to the MAINTENANCE screen, press the CLR key or
key.
- If the
key is pressed when cursor is on the “START” of the item 1 or 2, cursor returns on the item 1
or 2. (1.SELF DIAGNOSIS or 2.LCD DIAGNOSIS)
The outlines of menus are as follows;
1. SELF DIAGNOSIS:
NCR-333 is diagnosed. (See a))
2. LCD DIAGNOSIS:
LCD panel is diagnosed. (See b))
3. SELF DIAGNOSIS LOG:
The diagnostic result log of the item 1 is displayed. (See c))
6-43
a. The Diagnosis of equipment (SELF DIAGNOSIS)
Procudure
1) Select 1.SELF DIAGNOSIS, and press the ENT key. Cursor moves to the right side of ":".
2) Press the ▲ ▼ key and select the following items;
START:
Self diagnosis is started. However, the diagnostic results are not printed.
ST-PRTN: Self diagnosis is started. After self diagnosis is completed, the diagnosis results are
printed.
CANCEL: Self diagnosis is not started. Cursor returns to 1.SELF DIAGNOSIS.
3) Select the “START” or “ST-PRTN”, and then press the ENT key.
Self diagnosis starts by the “ROM” test and is ended by the “4209.5 kHz over all test”.
During diagnosis, “SELF DIAGNOSIS” of screen title repeats blink.
The buzzer sounds at the last of diagnosis, and check that the buzzer sounds normally. Press CLR key
to stop the beeping.
1.SELF DIAGNOSIS
: START
ROM
: GOOD
RAM
: GOOD
SIO
: GOOD
PS
: GOOD
ANTENNA CHECK
: GOOD
518KHZ
OVER ALL TEST:
490KHZ
OVER ALL TEST:
4209.5KHZ OVER ALL TEST:
“OVER ALL TEST” takes about 15 seconds per test.
Whenever one test (OVER ALL TEST) is completed, character string as shown in the following figure is
displayed. When “*“ is displayed in a character string, the test result is NG.
1.SELF DIAGNOSIS
: START
ROM
: GOOD
RAM
: GOOD
SIO
: GOOD
PS
: GOOD
ANTENNA CHECK
: GOOD
518KHZ
OVER ALL TEST: GOOD
490KHZ
OVER ALL TEST:
4209.5KHZ OVER ALL TEST:
(THE QUICK BLOWN FOX JUMPS OVER
THE LAZY DOG.123456789,?/+-:’=)
OVER ALL TEST:
"OVER ALL TEST" is the test which outputs
a test signal from the inside of the circuit,
and receives the signal from each receiver.
Test signal (Character strings):
THE QUICK BLOWN FOX JUMPS OVER
THE LAZY DOG. 123456789,?/+-:’=
Caution
When the result of the malfunction is displayed, contact our service center or an agency as soon as
possible after referring to troubleshooting of Chapter 7.
The list of diagnosis items
Diagnosis items
ROM
RAM
SIO
PS
ANTENNA CHECK
518KHZ OVER ALL TEST
490KHZ OVER ALL TEST
4209.5KHZ OVER ALL TEST
6-44
Explanation
The data memory and the program memory are checked.
When the program memory is abnormal (NG), ‘[1]’ is displayed,
and when the data memory is abnormal, ‘[2]’ is displayed.
The memory for temporarily storage is checked.
Serial interfaces are checked.
When the ‘ECDIS/GPS’ port is abnormal (NG), ‘[1]’ is displayed,
and when the ‘Maintenance/Printer’ port is abnormal, ‘[2]’ is
displayed, and when the ‘DISP’ port is abnormal, ‘[3]’ is
displayed.
The power supply part is checked.
Connection with NAVTEX antenna is checked.
Internal receiver (RX1) is checked.
Internal receiver (RX2) is checked.
Internal receiver (RX3) is checked.
Corrective Action
Replace CMJ-501N.
Replace CMN-2333.
b. The diagnosis of LCD panel (LCD DIAGNOSIS)
Procudure
1) Select 2.LCD DIAGNOSIS, and press the ENT key. Cursor moves to the right side of ":".
2) Press the ▲ ▼ key and select the following items;
START:
Diagnosis is started.
CANCEL: Diagnosis is canceled, and cursor returns to 2.LCD DIAGNOSIS.
3) Select the “START”, and press the ENT key.
This diagnosis blinks the viewing area (White -> Black -> White-> ...).
c. Self diagnosis log (SELF DIAGNOSIS LOG)
Procudure
1) Select 3.SELF DIAGNOSIS LOG, and press the ENT key. SELF DIAGNOSIS LOG screen appears.
The newest result is displayed on this screen.
2) To display the next old result, press the ▼ key. (Up to last 10 results)
The diagnosed time is displayed when external GPS receiver is connected.
”--/--/-- --:--“ is displayed when time is not able to be acquired. (External GPS receiver is not connected.)
SELF DIAGNOSIS LOG
9.RESULT 29/06/05
ROM[1][2]
RAM
SIO[1][2][3]
PS
ANTENNA CHECK
518KHZ
OVER
490KHZ
OVER
4209.5KHZ OVER
ⅩⅠ
12:34
To print a result to the external printer, press the * key
in order to display the sub screen.
Select the “[PRINT OUT]”, and press the ENT key.
Printing is started.
:NG
:GOOD
:NG
:GOOD
:GOOD
ALL TEST:GOOD
ALL TEST:GOOD
ALL TEST:GOOD
To stop printing, press the CLR key while printing.
To return to the SELF DIAGNOSIS screen, select the
“[CANCEL]” and press the ENT key.
SELF DIAGNOSIS LOG
ⅩⅠ
9.RESULT 29/06/05 12:34
ROM[1][2]
:NG
RAM
:GOOD
SIO[1][2][3]
:NG
PS *DIAGNOSIS LOG*
:GOOD
ANTENNA CHECK
:GOOD
518KHZ [PRINT
OVER
ALL TEST:GOOD
OUT]
490KHZ [CANCEL]
OVER ALL TEST:GOOD
4209.5KHZ OVER ALL TEST:GOOD
6-45
6.3.5.2 NAVTEX alarms (NAVTEX ALARM)
To display NAVTEX ALARM screen, select 2.NAVTEX ALARM from MAINTENANCE menu (6.3.5).
In the NAVTEX ALARM screen, the present alarm is displayed.
On the ALARM HISTORY screen, the alarm which occurred in operation can be displayed from the latest one
to a maximum of 20 affairs.
NAVTEX ALARM
ⅩⅠ
11/12/05 15:34
054,A,Printer err
Fig.6-15 NAVTEX ALARM screen
Notes
- To return to the MAINTENANCE screen, press the CLR key or
- "NO DATA" is displayed when NAVTEX alarm has not occurred.
key.
To print the NAVTEX alarms to the external printer, press the * key in order to display the sub screen.
Select the “[PRINT OUT]”, and press the ENT key. Printing is started.
To stop printing, press the CLR key while printing.
To return to the NAVTEX ALARM screen, select the “[CANCEL]” and press the ENT key.
NAVTEX ALARM
11/12/05 15:34
054,A,Printer err
*NAVTEX ALARM*
[HISTORY]
[PRINT OUT]
[CANCEL]
6-46
ⅩⅠ
a. Alarm history (ALARM HISTORY)
This screen displays a history of alarms which occur while the power is on. It displays the alarm history
from the most recent one maximum 20 lines.
To return to the NAVTEX ALARM screen, press the CLR key or
key.
NAVTEX ALARM
3.11/12/04 15:30 001 A
antenna malfunction
4.11/12/04 15:30 002 A
power supply error
5.02/11/04 02:31 001 V
antenna malfunction
6.02/11/04 02:19 001 A
antenna malfunction
7.23/09/04 22:15 001 V
antenna malfunction
8.23/09/04 22:15 002 V
power supply error
9.23/09/04 22:14 002 A
power supply error
10.23/09/04 22:13 001 A
antenna malfunction
ⅩⅠ
NAVTEX ALARM
3.11/12/04 15:30 001 A
antenna malfunction
4.11/12/04 15:30 002 A
power supply error
5.02/11/04 02:31 001 V
antenna
malfunction
*NAVTEX
ALARM*
6.02/11/04 02:19 001 A
antenna
malfunction
[PRINT
OUT]
7.23/09/04
22:15 001 V
[CANCEL]
antenna malfunction
8.23/09/04 22:15 002 V
power supply error
9.23/09/04 22:14 002 A
power supply error
10.23/09/04 22:13 001 A
antenna malfunction
ⅩⅠ
Fig.6-16 ALARM HISTORY screen
Procudure
1) To display the next old result, press the ▼ key.
- “ “ mark is displayed on the bottom line when the alarm history screen is able to scroll downward.
- “ “ mark is displayed on the top line when the alarm history screen is able to scroll upward.
- Press the ▲ ▼ key and scroll the viewing area.
The time of an alarm occurred and is restored is displayed when external GPS receiver is connected.
”--/--/-- --:--“ is displayed when time is not able to be acquired. (External GPS receiver is not connected.)
The display of the alarm is described.
Alarm message: 001, V, antenna malfufnction
1 2
1: The alarm number (refer to the following table)
2: The alarm condition -> “V”: Healthy status, “A”: Alarm is occurring
3: Alarm’s description text (refer to the following table)
The list of NAVTEX alarm
Alarm No.
002
003
004
005
006
051
052
053
054
055
Alarm’s description text
Receiver 1 malfunction
Receiver 2 malfunction
Receiver 3 malfunction
General failure
Built in self test failure
Antenna malfunction
Flash memory error
Rx unit modem error
Printer error
EXT SIO output error
The contents of unusual detection
Unusual detection at the RX1
Unusual detection at the RX2
Unusual detection at the RX3
Unusual detection at the power supply part
Self diagnosis failure
Unusual detection of antenna connection
The data in a memory is broken.
Unusual detection at the modem part
External printer has malfunction
Unusual detection at the “DISP” output port
2) To print the NAVTEX alarms to the external printer, press the * key in order to display the sub screen.
Select the “[PRINT OUT]”, and press the ENT key. Printing is started.
[PRINT OUT]: Printing is started.
[CANCEL]:
Diagnosis is canceled, and the sub screen is closed.
6-47
6.3.5.3 Setting status of the NAVTEX Receiver (STATUS)
To display STATUS screen, select 3.STATUS from MAINTENANCE menu (6.3.5).
The setting information of NCR-333 is displayed on the screen.
STATUS
ⅩⅠ
NAVAREA: ⅩⅠ
518KHZ DISABLED AREA:
A--D-----J----OPQR-------490KHZ DISABLED AREA:
---------J-------------XYZ
4209.5KHZ DISABLED AREA:
---D----------OPQR-------518KHZ DISABLED MESSAGE TYPE:
-----EF-----MNOPQR-------490KHZ DISABLED MESSAGE TYPE:
-----EF-----MNOPQR-------4209.5KHZ DISABLED MESSAGE TYPE:
-----EF-----MNOPQR-------N OF STORED MSG: 94: 52: 22
N OF SAVE
MSG: 39: 21:
Fig.6-17 STATUS screen
The setting information of each items are as follows;
- 518 (490, 4209.5) kHz DISABLED AREA: The alphabet of stations which does not receive is displayed.
- 518 (490, 4209.5) kHz DISABLED MESSAGE TYPE:
The alphabet of message type which does not receive is displayed.
- N OF STORED MSG: The number of the stored messages is displayed. Starting from the left, 518k,
490k, and 4209.5 kHz are displayed. When the number of the stored messages
is the maximum, it is displayed as “FULL”.
- N OF SAVE MSG:
The number of the saved messages is displayed. Starting from the left, 518k,
490k, and 4209.5 kHz are displayed. When the number of the saved messages
is the maximum, it is displayed as “FULL”.
Notes
- To return to the MAINTENANCE screen, press the CLR key or
NAVTEX ALARM
ⅩⅠ
NAVAREA: ⅩⅠ
518KHZ DISABLED AREA:
A—D-----J----OPQR-------490KHZ DISABLED AREA:
---------J-------------XYZ
*STATUS*
4209.5KHZ
DISABLED AREA:
---D----------OPQR-------[PRINT MESSAGE
OUT]
518KHZ DISABLED
TYPE:
-----EF-----MNOPQR-------[DATA
OUT]
490KHZ DISABLED
MESSAGE TYPE:
[CANCEL]
-----EF-----MNOPQR-------4209.5KHZ DISABLED MESSAGE TYPE:
-----EF-----MNOPQR-------N OF STORED MSG:
94:
52: 100
N OF SAVE
MSG:
39:
40:FULL
6-48
key.
Press the * key in order to display the sub screen.
To print the setting status to the external printer, select
the “[PRINT OUT]”, and press the ENT key.
To stop printing, press the CLR key while printing.
To output the status data to serial ports, select the
“[DATA OUT]”, and press the ENT key.
To stop outputting press the CLR key while data
outputting.
To return to the STATUS screen, select the “[CANCEL]”
and press the ENT key.
6.3.5.4 Port monitor (PORT MONITOR)
Select 4.PORT MONITOR, and press the ENT key. PORT MONITOR screen appears.
Select the port for monitoring. It can check whether data is normally outputted from the port.
In addition, the displayed data can be stored temporarily to be rechecked.
PORT MONITOR
ⅩⅠ
1.PORT SELECTION: OFF
2.PORT LOG
Fig.6-18 PORT MONITOR screen
Procudure
1. Press the ▲ ▼ key in order to select the items.
2. When the ENT key is pressed, the menu screen of selected item appears.
Pressing the
key can display the same.
- When cursor is on the item 1, cursor moves to the right side of ":"
- When cursor is on the item 2, the menu screen of item 2 appears.
Notes
- To return to the MAINTENANCE screen, press the CLR key or
key.
- If the
key is pressed when cursor is on the right side of ":" of the item 1, cursor returns on the item
1. (1.PORT SELCTION)
The outlines of menus are as follows;
1. PORT SELECTION:
Select the port to check the serial in/output data. (See a. The check of
in/output data)
2. PORT LOG:
The data stored temporarily is displayed. (See c. Port log)
6-49
a. The check of in/output data (PORT SELECTION)
Procudure
1) Select 1.PORT SELECTION, and press the ENT key. Cursor moves to the right side of ":".
2) Press the ▲ ▼
OFF:
GPS IN:
DISP IN:
DISP OUT:
key and select the following items;
The monitoring of each port does not carry out.
Input data of the GPS port
Input data of the DISP (Option) port
Output data of the DISP (Option) port
3) Example - Select the “GPS IN”, and press the ENT key.
PORT MONITOR menu screen changes to the data display screen.
PORT MONITOR
1. PORT MONITOR: GPS IN
ⅩⅠ
ENT
2. PORT LOG
CLR
PORT MONITOR
ⅩⅠ
$PRMC,012601.00,A,3541.273,N,1393
4.251,E,00.0,158.,020903,00.,W,D*2
$GPGLL,3541.273,N,13934.251,E,0126
01.0
$GPGGA,012602.00,3541.273,N,13934.
251,E,2,08,01.0,+0050,M,+039,M,05,
,0686*5C
$PRMC,012601.00,A,3541.273,N,1393
4.251,E,00.0,158.,020903,00.,W,D*2
$GPGLL,3541.273,N,13934.251,E,0126
01.0
$GPGGA,012602.00,3541.273,N,13934.
251,E,2,08,01.0,+0050,M,+039,M,05,
,0686*5C
Notes
- When neither the GPS receiver nor MPD is connected to the port of “GPS IN” and “DISP IN”, nothing is
displayed on the data display screen.
b. Store the displaying data temporarily
Procudure
1) Press the * key. The sub screen appears.
2) Select the “[START]”, and press the ENT key. Storing of
the displaying data is started.
During storing, the following is displayed on the screen
title.
“ NOW LOGGING... “
Notes
- When the MENU, DISP or USER key is pressed,
storing of the displaying data is stopped.
- Data is recordable to two screens.
- Data is stored until it turns off the power.
PORT MONITOR
ⅩⅠ
$PRMC,012601.00,A,3541.273,N,1393
4.251,E,00.0,158.,020903,00.,W,D*2
$GPGLL,3541.273,N,13934.251,E,0126
01.0
$GPGGA,012602.00,3541.273,N,13934.
*PORT MONITOR*
251,E,2,08,01.0,+0050,M,+039,M,05,
,0686*5C
[START]
$PRMC,012601.00,A,3541.273,N,1393
[STOP]
4.251,E,00.0,158.,020903,00.,W,D*2
$GPGLL,3541.273,N,13934.251,E,0126
01.0
$GPGGA,012602.00,3541.273,N,13934.
251,E,2,08,01.0,+0050,M,+039,M,05,
,0686*5C
3) For canceling, select the “[STOP]” and press the ENT key.
The sub screen is closed, and storing of the displaying data is stopped.
6-50
c. Port log（PORT LOG）
Procudure
1) Select 2.PORT LOG, and press the ENT key. PORT LOG screen appears.
The data stored in the PORT MONITOR is displayed on this screen.
2) “ “ mark is displayed on the bottom line when the PORT LOG screen is able to scroll downward.
- “ “ mark is displayed on the top line when the PORT LOG screen is able to scroll upward.
Press the ▲ ▼ key and scroll the viewing area.
PORT LOG
ⅩⅠ
1.PORT MONITOR: GPS IN
ENT
2. PORT LOG
CLR
PORT LOG
ⅩⅠ
$PRMC,012601.00,A,3541.273,N,1393
4.251,E,00.0,158.,020903,00.,W,D*2
$GPGLL,3541.273,N,13934.251,E,0126
01.0
$GPGGA,012602.00,3541.273,N,13934.
*PORT LOG*
251,E,2,08,01.0,+0050,M,+039,M,05,
,0686*5C
[PRINT OUT]
$PRMC,012601.00,A,3541.273,N,1393
[DATA
OUT]
4.251,E,00.0,158.,020903,00.,W,D*2
[CANCEL]
$GPGLL,3541.273,N,13934.251,E,0126
01.0
$GPGGA,012602.00,3541.273,N,13934.
251,E,2,08,01.0,+0050,M,+039,M,05,
,0686*5C
PORT LOG
ⅩⅠ
$PRMC,012601.00,A,3541.273,N,1393
4.251,E,00.0,158.,020903,00.,W,D*2
$GPGLL,3541.273,N,13934.251,E,0126
01.0
$GPGGA,012602.00,3541.273,N,13934.
251,E,2,08,01.0,+0050,M,+039,M,05,
,0686*5C
$PRMC,012601.00,A,3541.273,N,1393
4.251,E,00.0,158.,020903,00.,W,D*2
$GPGLL,3541.273,N,13934.251,E,0126
01.0
$GPGGA,012602.00,3541.273,N,13934.
251,E,2,08,01.0,+0050,M,+039,M,05,
,0686*5C
Press the * key. The sub screen appears.
To print the setting status to the external printer, select
the “[PRINT OUT]”, and press the ENT key.
To stop printing, press the CLR key while printing.
To output the status data to serial ports, select the
“[DATA OUT]”, and press the ENT key.
To stop outputting, press the CLR key while data
outputting.
To return to the PORT LOG screen, select
“[CANCEL]” and press the ENT key.
the
Notes
- All the character strings displayed on the PORT LOG screen are printed.
6-51
6.3.5.5 Software version (SOFTWARE VERSION)
When MAINTENANCE menu screen is displayed, the present software version is displayed on the item 5.
To display the MAIN MENU, press the CLR key.
MANINTENANCE
ⅩⅠ
1.SELF DIAGNOSIS
2.NAVTEX ALARM
3.STATUS
4.PORT MONITOR
5.SOFTWARE VERSION
- PROGRAM : 12.34
- LANGUAGE: 21A
- OPTION : ---
Fig.6-19 Maintenance manu screen
The explanations of each item are as follows;
- PROGRAM:
Program version is displayed.
- LANGUAGE:
Langage version is displayed.
- OPTION:
Option langage version is displayed.
When the option language is not installed, ”---“ is displayed.
6.3.6 The display language setting (LANGUAGE)
To select the display language, select 6.LANGUAGE from MAIN MENU (6.3).
Press the ▲ ▼ key and select the language. When the ENT key is pressed, menu screens are displayed in
the selected language.
6.LANGUAGE: ENGLISH
When the language data is already installed, the language name is displayed as follows.
- FRENCH
- PORTUGUESE
- ITALIAN
- SPANISH
When the option language is already installed, the option language name is displayed.
The initial setting is “ENGLISH”.
6-52
7.
MAINTENANCE AND INSPECTION
The performance and longevity of this equipment depend on careful maintenance. To maintain
the best performance, the following periodic inspections are highly recommended.
CAUTION
Keep the power supply voltage within the specified value (10.8 - 35Vdc).
Know the condition of normal status when the equipment is properly functioning.
Keep comparing the current status to the normal status to immediately detect any
malfunctions.
WARNING
Do not attempt to inspect or repair the inside of this equipment with the
exception of qualified service personnel, as doing so may cause fire, electric
shock or malfunction. If any malfunctions are detected, contact our service
center or agents.
Use only specified fuses.
The use of other fuse may cause fire and/or damage.
The fuses are used for NBG-319 or NBG-320.
The power switch on the power distribution panel must be turned off during
replacing a fuse. Remove the cap of the front panel, and then exchange
fuses.
7. 1 General Maintenance and Inspection
Below are listed general maintaining and inspecting items, which can be done with usual tools
and apparatus.
No.
Item
Maintenance and inspection
Cleaning
Gently clean the surface of the panel, switches, and cover with soft cloth or
silicon oil. No oil is needed because this unit has no moving mechanisms
inside.
Looseness
of parts
Inspect for looseness and correctly tighten the following:
Screws, nuts and connectors.
7-1
7. 2 Periodic Inspection
Regarding the functions for performing self-diagnosis and monitoring the system status, please
refer to “6.3.5 Maintenance Menu”
7.2.1 Confirming the RX station and Message type
To check the receiving station and message type, please refer to 6.1.3 and 6.3.2. Be sure to set
up the receiving station and message type correctly.
7.2.2 Confirming the Alarm Status
With referring 6.3.5.2, confirm that failure alarm is not occurring. If any alarm occurs, check the
cause of the alarm. NCR-333 Alarm Table is followings.
NCR-333 Alarm Table
Failure alarm list (ALR sentence output)
Alarm
Indication
No.
005
General failure
006
Built in self test failure
006
Built in self test failure
051
Antenna malfunction
002
006
Receiver 1 malfunction
Built in self test failure
003
006
Receiver 2 malfunction
Built in self test failure
004
006
Receiver 3 malfunction
Built in self test failure
002
053
003
053
004
053
051
Receiver 1 malfunction
Rx unit modem error
Receiver 2 malfunction
Rx unit modem error
Receiver 3 malfunction
Rx unit modem error
Antenna malfunction
005
054
055
General failure
Printer error
EXT SIO output error
7-2
Alarm Occurrence Conditions
After carrying out self-diagnosis, NCR-333 detected
that the input voltage was abnormal.
After carrying out self-diagnosis, NCR-333 detected
that the output voltage of antenna terminal was low
voltage.
After carrying out self-diagnosis, NCR-333 detected
that the receiver 1 (518kHz) could not receive
because of abnormalities.
After carrying out self-diagnosis, NCR-333 detected
that the receiver 2 (490kHz) could not receive
because of abnormalities.
After carrying out self-diagnosis, NCR-333 detected
that the receiver 3 (4209.5kHz) could not receive
because of abnormalities.
The receiver 1 (518kHz) could not receive because
of internal MODEM failure.
The receiver 2 (490kHz) could not receive because
of internal MODEM failure.
The receiver 3 (4209.5kHz) could not receive
because of internal MODEM failure.
The output voltage of antenna terminal is low
voltage.
The input voltage is low level.
External printer is abnormal.
“DISP” output port is abnormal.
7. 3 Trouble Shootings
7.3.1 Trouble Shootings
WARNING
Do not attempt to inspect or repair the inside of this equipment with the
exception of qualified service personnel, as doing so may cause fire, electric
shock or malfunction. If any malfunctions are detected, contact our service
center or agents.
For reference, this section presents a troubleshooting guideline for finding defective sections.
Symptom of Error
Possible Cause or Cause of Fault Countermeasures
Power is not supplied Power is not distributed from the Supply power from the distribution
when the power switch inboard distribution panel.
panel.
is pressed.
Power is not supplied from the Check that the wiring of the power
power supply unit or NCR-333.
unit is correct.
Check that the output voltage of the
power unit or NCR-333 is correct.
Power that the power unit supplies Replace the power unit.
is out of range.
The fuses in the Power Supply Unit Check that the wiring is correct and
(Option) are blown out.
replace the fuses.
The power supply cable is broken.
Replace the power supply cable.
The controller switch is broken.
Replace the CMD-953 circuit board.
Some dots are missing The LCD malfunctions.
Replace the LCD.
on the LCD.
The control unit malfunctions.
Replace the CMJ-501N circuit
board.
No alarming sound is The buzzer malfunctions.
Replace the CMD-953 circuit board.
generated.
The control unit malfunctions.
Replace the CMJ-501N circuit
board.
The illumination does The control unit malfunctions.
not light.
The LCD malfunctions.
No NAVTEX message The polarity or antenna cable is
is received.
incorrect.
Neither the receiving station nor the
message type is selected correctly.
The NAVTEX antenna (NAW-333)
is damaged.
The
following
alarm number
appears: 002, 003, or 004.
Internal receiver 1, 2 or 3 is broken.
Sensor data (external The polarity of the serial cable is
GPS,
gyro,
and incorrect.
rate-of-turn) cannot be The interface between the sensor
loaded.
and NCR-333 is incorrect.
The sentence that the sensor
generates is not supported by the
NCR-333.
The serial format (baud rate, etc.)
does not meet the setting of the
controller.
The sensor (GPS, gyro, rate-of-turn
indicator) malfunctions.
Replace the CMJ-501N circuit
board.
Replace the LCD.
Check if the polarity is correct and
connect it.
Refer to “6.3.1” or “6.3.2”.
Replace the NAW-333.
Replace the CMN-2333.
Check if the polarity is correct and
connect it.
Check if the interface is correct
before its connection.
Check the output command and the
version.
Check the serial format of the
sensor.
Replace the sensor.
7-3
Symptom of Error
Sensor data (external
GPS,
gyro,
and
rate-of-turn) cannot be
loaded.
The external printer
does not print
Possible Cause or Cause of Fault Countermeasures
The DPU (CMJ-501N) malfunctions. Replace the CMJ-501N
board.
circuit
The external printer is not ON.
Turn on the external printer.
The printer power is not turned on.
Check the printer power cable.
Printer property (printer settings) is Refer to “6.3.4.5”.
incorrect.
7.3.2 Maintenance Units
Maintenance units for repair are followings.
No.
Fuses
No.
Unit Name
RX UNIT
DPU
KEYBOARD UNIT
NAVTEX ANTENNA
POWER SUPPLY UNIT
POWER SUPPLY UNIT
Whip Antenna
Model
CMN-2333
CMJ-501N
CMD-953
NAW-333-1
NBG-319
NBG-320
5ABBE00001
Note
ANTENNA for NCR-333
DC: +12/24Vdc
AC: 110/220Vac, DC: +12/24Vdc
0.6 m
Unit Name
5A Fuse
2A Fuse
4A Fuse
Model
ULTSC 5A N1
MQ4 250V 2A
MQ2 125V 4A
Note
For NBG-319
For NBG-320
For NBG-320
7.3.3 Spear parts for periodic maintenance
Spear parts for periodic maintenance are followings.
No.
7-4
Unit Name
LCD Unit
Code
CCN-392
Decline period
40,000 hours
Printer
(Option)
DPU-414
Approx. 500,000 lines
Note
5 years in continuous operation
When the thermal paper of 25m roll
length is used, about 90 thermal
papers can be used.
8. AFTER-SALES SERVICE
Warranty
z Warranty period is one year from the purchase day.
Warranty
z Keeping period of maintenance parts is ten years from the production is discontinued.
Before returning repair
If what appears to be a malfunction is detected, refer to “7.3 Troubleshooting” to check if the
equipment is actually defective before requesting repair.
If the defect persists, immediately stop operation and call our service center or agents.
z During the warranty period, our agencies or we will repair the malfunction without any fee,
according to the specified procedure.
z After the warranty expires, we will repair the malfunction for a fee, if repair is possible. In this case,
send the parts or we’ll repair onboard in a specified port. The parts may be repaired in a plant if it’s
unrepairable onboard.
z Item for notification
Product name, type, manufactured data, serial number,
information about the malfunction (the more detailed, the better),
information about the alarm number and software version,
your company or organization name, address and phone number.
Periodical maintenance recommendation
Performance of this equipment may degrade over time because parts wear out, although degradation
depends on how this unit has been maintained.
We recommend periodic professional maintenance checks in addition to daily maintenance.
Call our service center or agents for periodic professional maintenance (This maintenance requires a
service charge).
Call our office or the nearest agency for detailed information about after-sales service.
[JRC offices or the nearest agency]
See the List of JRC offices or the nearest agency at the end of this manual.
8-1
8-2
9. SPECIFICATIONS
9.1 NAVTEX RECEIVER (NCR-333)
9.1.1 Receiver
(1)
(2)
(3)
(4)
Receiving frequency
Receiving modulation
Sensitivity
Antenna input
: 518kHz, 490kHz and 4209.5kHz
: F1B
: CER ≦ 1x10-2 at 1uV (CER: Character Error Rate)
: 50 ohms for NAVTEX antenna
50 ohms for wide-band antenna
High impedance for wire antenna
9.1.2 Operation panel
(1)
(2)
(3)
(4)
Type of display
Key board
Back-light
Dimmer control
: 5.7-inch FSTN LCD, 320×240 dots
: 12 keys
: For LCD and key board
: Bright, medium1, medium2, off (Selectable from keyboard)
9.1.3 Power supply
(1) Input voltage
(2) Power consumption
: 12 / 24Vdc (+30%, -10%)
: 9 W (at 24 Vdc input)
9.1.4 External interfaces
(1) INS (Integrated Navigation System) communication ports DATA IN / DATA OUT
One communication port meets the requirements of IEC 61162-1
- Baudrate
: 4800bps
- Data bit
: 8bits
- Parity
: none
- Stop bit
: 1bit
- Flow control
: none
(2) External printer / maintenance port PRINTER/MAINTENANCE
One communication port meets the requirements of RS-232C (D-sub 9pin).
- Baudrate
: User setting (4800 / 9600 / 38.4k bps)
- Data bit
: 8bits
- Parity
: none
- Stop bit
: 1bit
- Flow control
: User setting (Hard / None)
(3) Relay terminals BK
One port for Break in relay signal
(4) Relay terminals EXT ALR
One port for external alarm device
(5) Remote maintenance data output port DATA OUT2
One output port meets the requirements of IEC 61162-1
(6) MPD (Multi purpose display) communication port DISP
One communication port meets the requirements of RS-485
9-1
9.1.5 Environmental condition
Durability and resistance to environmental conditions: protected from the weather (IEC 60945)
(1) Operating temperature
: -15°C to +55°C (IEC 60945)
(2) Storage temperature
: -25°C to +75°C
(3) Water resistance
: IPX2
9.1.6 Supported interface sentences
Indication
DATA IN
DATA OUT
Sentence format
Supported sentence formatters
Input data
IEC61162-1
Longitude/Latitude
(NMEA Ver 1.5 - Time of Position
2.3)
Datum Reference
IEC61097-6
IEC61162-1
IEC61097-6
Speed Over Ground (SOG)
Course Over Ground (COG)
Heading
Rate of Turn
Acknowledge alarm
Request NAVTEX messages
Set NAVTEX mask
Output data
Set alarm state
New NAVTEX received message
Set NAVTEX mask
RMC, GGA,GLL
DTM
RMC, VTG
RMC, VTG
HDT
ROT
ACK
NRQ
NMK
ALR
NRX
NMK
9.1.7 Received message log
(1) Stored message : Stores the 200 last received messages (*1). (Each channel)
(2) Saved message : Stores the 50 stored messages (*1). (Each channel)
(*1)
: message ... 500 character long message
Stored messages are erased 70 hours after their reception.
The source of time for handling message ageing is RMC sentence from an external source
(DATA IN).
When the data from the external source is not inputted, it is counted by the internal timer.
9-2
9.2 NAVTEX ANTENNA (NAW-333 - Option)
9.2.1 Electrical characteristics
(1) Receiving frequency
(2) Bandwidth
(3) Consumption current
(4) Impedance
: 518kHz, 490kHz and 4209.5kHz
: 504kHz
: ±20kHz
4209.5kHz
: ±100kHz
: 7Vdc 13mA (Typ.)
: 50 ohms
9.2.2 Environmental condition
(1) Operating temperature
: -25°C to +55°C (IEC 60945)
9.3 POWER SUPPLY UNIT (NBG-320 - Option)
(1) Input voltage
(2) Output voltage
(3) Maximum current
: 100-120 / 200-220 Vdc ±10%, 50/60Hz Single phase
: 24Vdc (+30%, -10%) (Back up power supply)
: Typ. 12Vdc ±10%
6.5Vdc ±10% (for External Printer)
: 1.5 A (24V)
2.0 A (6.5V)
9.4 POWER SUPPLY UNIT (NBG-319 - Option)
(1) Input voltage
(2) Output voltage
(3) Maximum current
: 10.8 - 35Vdc
: 10.8 - 35Vdc
Typ. 6.5Vdc ±10% (for External Printer)
: 1.5 A (12 / 24V)
2.0 A (6.5V)
9-3
9-4
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 95
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:9ed5bb99-dd32-4f47-8481-9bb72a51b0c5
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2005:07:01 17:16:02+09:00
Modify Date                     : 2005:07:01 18:05:43+09:00
Metadata Date                   : 2005:07:01 18:05:43+09:00
Document ID                     : uuid:dd66df6c-97f5-46a3-b82c-5f4e4cb1c283
Format                          : application/pdf
Title                           : untitled
EXIF Metadata provided by EXIF.tools
FCC ID Filing: CKENCR-333

Navigation menu