Japan Radio Co NKE1066 MARINE RADAR User Manual 4

Japan Radio Co Ltd. MARINE RADAR 4

User Manual 4

  Chapter 8   DETAIL PERFORMANCE SETTING 100  8-1-1 MAIN BANG SUPPRESSION  (Usually, doesn’t need set up. adjust if necessary)  This adjustment is decrease the transmitted signal which appears as a circular echo around the center. Adjustment is done so as to main bang is observe slightly seen. Excess adjusting is danger for nearest small target observation.   If the main bang is not so big, use as factory setting.
  Chapter 8    DETAIL RFORMANCE SETTING 101  8-1-2 TARGET EXPANSION Level setting. The level which can be set up is level 1, the level 2, the level 3, and the level 4. Expansion and the magnifying the observation target size.. Tap the “Level1, Level2, Level3, Level4“ icon.                 8-1-3 GAIN LEVEL (Important adjustment. Since adjusted in factory, adjustment is not necessary in the field.)
  Chapter 8   DETAIL PERFORMANCE SETTING 102  8-1-4 SEA CLUTTER LEVEL (Important adjustment. Since adjusted in factory, adjustment is not necessary in the field.)
  Chapter 8    DETAIL RFORMANCE SETTING 103  8-1-5 RAIN AND SNOW CLUTTER LEVEL (Important adjustment. Since adjusted in factory, adjustment is not necessary in the field.)
  Chapter 8   DETAIL PERFORMANCE SETTING 104  8-1-6 RADAR Alarm LEVEL                                  Set up Alarm 1 Level Set up Alarm 2 Level
  Chapter 8    DETAIL RFORMANCE SETTING 105  8-2 TT(TARGET TRACKING) FUNCTION (Important adjustment. Since adjusted in factory, adjustment is not necessary in the field.)          Vector shows the movement of the target.   Vector Constant large. Vector is stable, but the response is slow.   Vector Constant small. Vector is unstable, but the response is quick..                Tap Vector Constant, setting Bar appears lower part of    screen. Set up by flick or tap + -. Rotary knob adjusting is possible. Click and set.        Gate Display:      The region automatically search target moving area.   ON: Confirmation is possible under green searching area. OFF: Doesn’t display automatically searching area.
  Chapter 8   DETAIL PERFORMANCE SETTING 106  Gate Size:  Set up the region size which can search the moving target automatically.             Wide region:    Possible to track fast moving target, but many clutters are include.     Sometime do miss tracking because of much noise. Narrow region    Possible to track stable, but fast moving target are tend to lost. Because of first target soon goes outside of the region.
  Chapter 8    DETAIL RFORMANCE SETTING 107  8-3 SCANNER FUNCTION                8-3-1 PULSE REPETITION FREQUENCY FINE TUNING (PRF ADJUST)  When existing the same frequency radar, in the same area, they interfere each other. If p.r.f.(pulse reputation frequency)is the same, Interference can’t reject on the screen. In that case shift the p.r.f. a little may decrease the radar interference.  PRF Fine Tuning: If radar interference cannot reject completely, it is effective way to shift the PRF.            Watching the screen echo, rotate the Rotary knob and stop when radar interference are fade out from screen.
  Chapter 8   DETAIL PERFORMANCE SETTING 108  8-3-2 STAGGER TRIGGER  When existing the same frequency radar, in the same area, they interfere each other. If p.r.f.(pulse reputation frequency)is the same, Interference can’t reject on the screen. Another way to decease interference is shift the transmitting time randomly. Not synchronize signal which transmit randomly is eliminate. So decrease the other radar interference echo on screen.    ON Stagger: Stagger trigger is generated   OFF Stagger: Stagger trigger stop. (Normal trigger timing) Select and Tap   .          Watching the screen echo, select off or on when heavy radar interference on screen.  return to the menu
  Chapter 8    DETAIL RFORMANCE SETTING 109  8-3-3 SCANNER ROTATIONAL SPEED The rotational speed of inside microwave radiator is possible to change.  The sensitivity of radar are low speed is more higher. So scanner rotation speed is possible to change according observing range.                                    Every pulse length can select the Antenna rotation speed. Short range uses short pulse (SP). Medium range uses medium pulse (MP) Long range uses Long pulse (LP) Shorter range requires the High speed refresh screen. Longer range requires the Low speed for High sensitivity. User can select rotational speed according to his request.
  Chapter 8   DETAIL PERFORMANCE SETTING 110  8-3-4 ECONOMY MAGNETRON SETUP (PRF , PULSE LENGTH) The life of magnetron proportion to the total transmitting pulse power. Low power transmission makes magnetron life more longer.  Selection Normal:      It is the usual factory setup. Usually, this is chosen. Economy: Selected the shorter pulse, repeat frequency is also selected lowest 650 Hz.   The life of a magnetron keeps more longer time. Sensitivity is decrease somewhat from Normal. High Power: High sensitivity high performance.                 8-3-5 TIMED TX The life of magnetron proportion to the total transmitting pulse power. Timed TX can save magnetron life longer.                  return to the menu Select and Tap
  Chapter 8    DETAIL RFORMANCE SETTING 111  8-3-6 TUNE PEAK LEVEL Normally, adjustment is not necessary. (In case of adjustment the tuning peak point is shifted from maximum echo point.)   This adjustment must be done with (8-3-7 Tuning indicator) alternately.  Set RANGE at 24NM Display tuning level indicator menu. Tune maximum echo point. At this point adjust tuning level, so as to seen within the green bar. Adjusting data is 0 to 127   .           8-3-7 TUNE INDICATOR LEVEL Normally, adjustment is not necessary. (Adjust ,in case of tuning level is too low.)   Set RANGE at 24NM Display the Tune Indicator menu. Tuning region is 0 to 127 NOTE!  If tuning level is too excess setting, can’t work automatic tuning function.      Adjust the tuning level bar moves within 80 to 90%.
  Chapter 8   DETAIL PERFORMANCE SETTING 112  8-4 CONTROL                8-4-1 BEARING REFERENCE            8-4-2 BUZZER            Select Bearing Mode True or Relative Set up the Buzzer sound Level.
  Chapter 8    DETAIL RFORMANCE SETTING 113                                     Set up the Every sound Level.
  Chapter 8   DETAIL PERFORMANCE SETTING 114  8-5 MAINTENANCE SETTING   8-5-1 SYSTEM TIME CLEAR  8-5-2 SCANNER TIME CLEAR                                  Clear System time  Clear Scanner time.
  Chapter 8    DETAIL RFORMANCE SETTING 115
  Chapter 8   DETAIL PERFORMANCE SETTING 116  8-6 SYSTEM SETTING                  8-6-1 MASTER/SLAVE/DEMO           8-6-2 Own Ship Outline               Set up the operating mode. Mode selection of display. Master: control scanner.(Stand alone.). Slave: Receive another radar signal and display. can’t control scanner. Demo: When use as carrying out the demonstration    Select Master Set up the Own ship’s Outline, length and scanner position.
  Chapter 8    DETAIL RFORMANCE SETTING 117                          8-6-3 UNIT Display units, such as distance, speed, depth of water, water temperature, and wind velocity. “NM”,” km”,” ktn”, etc. are possible to set up.
  Chapter 8   DETAIL PERFORMANCE SETTING 118
  Chapter 8    DETAIL RFORMANCE SETTING 119  8-6-4 MOVE OWN SHIP Means of Moving own ship. Select GPS, LOG, Dead Reckoning (dead-reckoning navigation), etc.
  Chapter 8   DETAIL PERFORMANCE SETTING 120  8-6-5 USE RANGE SELECT                                         Select the using unit. “NM”,”KM”,”SM”. Select the using NM range “ON”. Not using range, set up “OFF”.
  Chapter 8    DETAIL RFORMANCE SETTING 121                                          Select the using KM range “ON”. Not using range, set up “OFF”. Select the using SM range “ON”. Not using range, set up “OFF”.
  Chapter 8   DETAIL PERFORMANCE SETTING 122  8-7 DISPLAY SCREEN   Various display setting..                8-7-1 OWN VECTOR DISPLAY          8-7-2 ST-BY DISP SELECT   Selections whether at stand by state, display the numeric data on screen or not.            Select the using SM range “ON”. Not using range, set up “OFF#. Select the Own Vector display ON or OFF. Select the ST-BY Display. “Normal” “Graphical” “Numeric”.
  Chapter 8    DETAIL RFORMANCE SETTING 123                  8-7-3 OPERATION NUMERICAL DISPLAY          8-7-4DISPLAY COLOR                   “Normal”        “Graphical”          “Numeric”. Select the Display. OFF or ON Setting of screen color.
  Chapter 8   DETAIL PERFORMANCE SETTING 124                                               Black screen color. Select Brilliance Level Blue screen color. White screen color.
  Chapter 8    DETAIL RFORMANCE SETTING 125                                          Select Color Select Character Color Select Brilliance.  Select Brilliance. Level. Select Brilliance. Level. Select Echo Color
  Chapter 8   DETAIL PERFORMANCE SETTING 126                                   Select Brilliance. Level. Select Trails(Time) Color   Select Brilliance. Level. Select Trails(All) Color
  Chapter 8    DETAIL RFORMANCE SETTING 127                                       Select Brilliance. Level. Select Own Ships Color   Select Brilliance. Level. Select Target (TT/AIS) Color
  Chapter 8   DETAIL PERFORMANCE SETTING 128                                      Select Brilliance. Level. Select EBL/VRM Color   Select Brilliance. Level. Select Range Ring Color
  Chapter 8    DETAIL RFORMANCE SETTING 129                                             Select Brilliance. Level. Select Cursor Color   Select Brilliance. Level. Select AZ/Alarm Color
  Chapter 8   DETAIL PERFORMANCE SETTING 130  8-7-5WAYPOINT DISPLAY                 8-7-6AIS FILTER                      Select Waypoint Display.  Select Waypoint Display “ON” or ”OFF”. Set up AIS Filter Range. Select AIS Filter
  Chapter 8    DETAIL RFORMANCE SETTING 131  8-8 ERROR ALARM MASK Ignore the unnecessary error signal’s alarm.                   8-8-1 SCANNER     The error signal generated in the scanner.
  Chapter 8   DETAIL PERFORMANCE SETTING 132                                           Scanner(Data) Scanner(Video)  Scanner(Trigger) Scanner(Azi)  Scanner(HL)  Scanner(MHV) Scanner(Heater)
  Chapter 8    DETAIL RFORMANCE SETTING 133  8-8-2 DISPLAY UNIT     The error signal generated in the display unit.                                       Display Unit(Video) Display Unit(Trigger)  Display Unit(AZI)
  Chapter 8   DETAIL PERFORMANCE SETTING 134                              ]        Display Unit(HL)  Display Unit(DSP) COM Port
  Chapter 8    DETAIL RFORMANCE SETTING 135  8-8-3 CONNECTION DEVICE     The error signal generated about the connected device.                                 Gyro(Time Out) Log (Time Out)  GPS (Time Out) are the same method.
  Chapter 8   DETAIL PERFORMANCE SETTING 136  8-8-4 RX DATA     The error signal about receiving data from another equipment.                                        Compass data Alarm  Log data Alarm  2Axis Log data Alarm
  Chapter 8    DETAIL RFORMANCE SETTING 137                                          Course / Speed data Alarm  Depth data Alarm  Temperature data Alarm Wind data Alarm  Rate of Turn data Alarm  2Rudder data Alarm WPT data Alarm  LAT/LON data Alarm  Datum data Alarm Status data Alarm  HDOP data Alarm  AIS data Alarm

Navigation menu