Japan Radio Co NKE1125 Marine Radar User Manual JMA 9100 series RADAR Instruction Manual

Download:
Mirror Download [FCC.gov]
Document ID	993941
Application ID	rbZy8EM6kzwEM9+RFJZXCQ==
Document Description	Users Manual 3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	345.99kB (4324928 bits)
Date Submitted	2008-09-02 00:00:00
Date Available	2008-09-02 00:00:00
Creation Date	2008-09-02 14:33:09
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2008-09-02 14:34:25
Document Title	JMA-9100 series RADAR Instruction Manual
Document Creator	FrameMaker 8.0
Document Author:	Japan Radio Co.,Ltd Marine Radar Group

JMA-9100 Instruction Manual
8.4.4
8.COUNTERMEASURE FOR TROUBLE ...
8.4 REPLACEMENT OF MAJOR PARTS
Replacement of LCD Monitor
Replacement of LCD monitor must be made by specialized
service personnel.
For details, refer to Service Manual.
8.4.4.1
Display Unit NCD-4990
Do not touch the LCD screen directly with your fingers.
Do not touch the AR filter directly with your fingers.
Perform the replacement work on a soft cloth to avoid damage to the LCD screen and
other parts.
[Required tools]
• A Phillips screwdriver for 4 mm screws
• A Phillips screwdriver for 6 mm screws
[Disassembly]
1)
Remove the tilt fixing handle (standalone type
only).
2)
Tilt up the screen as much as you can
(standalone type only).
8－ 33
JMA-9100 Instruction Manual
3)
8.COUNTERMEASURE FOR TROUBLE ...
8.4 REPLACEMENT OF MAJOR PARTS
Remove the screws (M6) from the four
corners and displace the face cover.
Remove
4)
LRemove the LCD operation circuit
cables and remove the face cover.
Remove
5)
Remove six M4 screws.
Remove
Remove
8－ 34
JMA-9100 Instruction Manual
8.COUNTERMEASURE FOR TROUBLE ...
6)
Displace the module and remove the three
cables.
7)
Remove the LCD module.
8.4 REPLACEMENT OF MAJOR PARTS
Remove
[Assembly]
1)
Tighten the lower three M4 screws halfway.
2)
Connect the cables to the LCD module.
3)
Align the module to the lower three screws
and insert it downward.
4)
Check the positions of the two bosses and
ensure that appropriate space is maintained
under the LCD module. Tighten the six
screws evenly.
5)
Connect the LCD operation circuit cables
and attach the face cover.
6)
Tighten the screws at the four corners.
7)
Attach the tilt fixing handle.
Temporary
tightening
Positions of the
two bosses
[Operation Check]
1)
After completing the replacement
procedures, start the system to make sure that images are displayed properly.
2)
Turn the brightness knob to make sure the brightness can be changed between the
minimum and the maximum levels.
8－ 35
JMA-9100 Instruction Manual
8.4.5
8.COUNTERMEASURE FOR TROUBLE ...
8.4 REPLACEMENT OF MAJOR PARTS
Replacement of Backup Battery
Replacement of backup battery must be made by specialized
service personnel.
For details, refer to Service Manual.
A coin-cell battery maintains radar system configuration, date, and time
information while power off condition. Radar system configuration is saving to
non-volatile memory at fixed intervals.
8.4.5.1
About the Battery Alarm
If Battery Low
is appeared at the lower-right of the display when start up the
radar system, the battery has not enough time left to live. We recommend to
replace the battery.
If Battery Dead
is appeared at the lower-right of the display when start up the
radar system, the battery has no time left to live. There is a necessary to replace
the battery. In This condition, this radar system is restored configuration
information from flash memory and normal operation is available. However, you
turned of the radar system before saving to flash memory, the configuration
information is maybe lost. In this case, you must setup the configuration again.
About disposal of used battery, refer to Section 10.2.
8.4.5.2
How to Replacement of Backup Battery
[Required tools]
• A flat tip screwdriver for 6 mm screws
• A Phillips screwdriver for 4 mm screws
• A flat tip nonconductive screwdriver for 3 mm screws
8－ 36
JMA-9100 Instruction Manual
8.COUNTERMEASURE FOR TROUBLE ...
8.4 REPLACEMENT OF MAJOR PARTS
[Disassembly]
1)
Remove the four fixing screws to remove
the cover from the display unit (NCD4990).
（A flat tip screwdriver for 6 mm screws）
Remove
For standalone type NCD-4990
For tabletop type: NDC-1399-9
Remove
2)
Remove the cable connected to the radar
processing circuit board.
The radar processing circuit is the first board
from the left.
3) Remove the two fixing screws (M4).
4) Pull out the board to the front.
5)
Insert the flat tip nonconductive screwdriver
for adjustment or some stick between the
battery and the battery holder and lift the
battery up.
8－ 37
Remove
JMA-9100 Instruction Manual
6)
8.COUNTERMEASURE FOR TROUBLE ...
8.4 REPLACEMENT OF MAJOR PARTS
Insert the flat tip nonconductive sscrewdriver
for adjustment or some stick to the location
shown in the figure below and slide the battery
sideways to remove the battery.
[Assembly]
1)
Check the polarity of the battery. Make sure
that the battery's positive (+) side is facing up.
2)
Slide the battery sideways into the battery
holder.
3)
Make sure that the battery is inserted fully.
[Check Item]
1)
Check that no error message comes up.
2)
Check that the system starts up normally.
[Notes]
8－ 38
JMA-9100 Instruction Manual
8.COUNTERMEASURE FOR TROUBLE ...
8.4 REPLACEMENT OF MAJOR PARTS
If you installed the battery with the wrong polarity, remove the battery immediately and
do not use the same battery again.
During the procedures, do not put the battery on any circuit board or conductive item.
To dispose of a used battery, follow the instructions provided in Section 10.2 "DISPOSAL
OF USED BATTERIES".
To disassemble of a used battery, have to use non-conductive tool.
8－ 39
JMA-9100 Instruction Manual
8.COUNTERMEASURE FOR TROUBLE ...
8－ 40
8.4 REPLACEMENT OF MAJOR PARTS
SECTION 9
TROUBLE SHOOTING AND
AFTER-SALES SERVICE
TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.1
FAULT FINDING .....................................................................................9-1
9.1.1
List of Alarms and other Indications .............................................9-1
9.1.2
Operation Checking ........................................................................9-5
9.1.3
Fuse Checking .................................................................................9-5
9.2
TROUBLE SHOOTING ...........................................................................9-6
9.2.1
Special Parts ....................................................................................9-7
9.2.2
Circuit Block to be Repaired ..........................................................9-8
9.3
AFTER-SALES SERVICE ....................................................................9-14
9.3.1
Keeping period of maintenance parts .........................................9-14
9.3.2
When you Request for Repair ......................................................9-14
9.3.3
Recommended Maintenance ........................................................9-14
JMA-9100 Instruction Manual
9.1
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.1 FAULT FINDING
FAULT FINDING
In case of semiconductor circuits, it is deemed that there are few cases in which
the used semiconductor devices have inferior quality or performance deterioration
except due to insufficient design or inspection or by other external and artificial
causes. In general, the relatively many causes are disconnection in a high-value
resistor due to moisture, a defective variable resistor and poor contact of a switch
or relay.
Some troubles are caused by defective parts, imperfect adjustment (such as tuning
adjustment) or insufficient service (such as poor cable contact). It will also be
effective to check and readjust these points.
9.1.1
List of Alarms and other Indications
The system automatically recognizes an internal alarm and displays the alarm
message. If an event which is not trouble but must be reported to the operator
occurs, the system notifies the operator of the event.
Error message and alarm are displayed in the lower right of the display. For more
details refer to page2-31 Alarm.
This section gives the list of alarms displayed by the system and other display
lists.
Table9-1： List of System Error Message
Message
Description
TXRX (SSW Off)
Scanner: Safety switch OFF.
TXRX (AZI)
Scanner: BP error.
TXRX (HL)
Scanner: HL error.
TXRX (MHV)
Scanner: Modulator's high voltage alarm.
TXRX (Data)
Scanner: No communication, communication mismatched,
checksum error, or collision.
TXRX (Heater)
Scanner: Magnetron heater voltage error.
TXRX (Reverse)
Scanner: Reverse rotation.
9－ 1
JMA-9100 Instruction Manual
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.1 FAULT FINDING
Table9-1： List of System Error Message
Message
Description
TXRX (Video)
Scanner: VIDEO error.
TXRX (Trigger)
Scanner: TRIGGER error..
TXRX (Fan 1)
Scanner: FAN 1 error.
TXRX (Fan 2)
Scanner: FAN 2 error.
TXRX (Motor)
Scanner: Motor current error.
Keyboard (Data)
Operation unit: Communication error or checksum error.
Keyboard2 (Data)
Second operation unit: Communication error or checksum error.
GYRO I/F (Data)
GYRO I/F: No communication or checksum error.
GYRO I/F (GYRO)
GYRO I/F: GYRO error (error bit detected).
GYRO I/F (Log)
GYRO I/F: Log error (error bit detected).
GPS (Status)
GPS status error.
Position (Data)
Latitude / longitude data: No communication or data error.
Date (Data)
Date data: No communication or data error.
Speed (Log)
1-axis log: No communication or data error.
Speed (2AXW)
2-axis log (speed over water): No communication or data error.
Speed (2AXG)
2-axis log (speed over ground): No communication or data error.
Speed (GPS)
GPS speed: No communication or data error.
PROC (Interrupt)
Process unit: Interrupt error.
PROC (AZI)
Process unit: AZI error.
PROC (HL)
Process unit: HL error.Error during interrupt from ASIC1 to
RADAR DSP.
ASIC1 to RADAR
VIDEO error.
PROC (Video)
Trigger error.
PROC (Trigger)
Heading data: No communication or data error.
Heading (Data)
Water depth: No communication or data error.
Depth (Data)
Water temperature: No communication or data error.
TEMP. (Data)
Wind direction/velocity: No communication or data error.
Wind (Data)
Tidal current: No communication or data error.
Current (Data)
Rate of Turn: No communication or data error.
ROT (Data)
Rudder Sensor Angle: No communication or data error.
RSA (Data)
APB: No communication or data error.
Autopilot (Data)
LCD monitor: Fan error.
Fan (LCD)
RADAR Process Unit Interconnection: Fan error.
Fan (Power)
Power Supply: Fan error.
Fan (PROC)
Scanner: Safety switch OFF.
Table9-2： List of Notification
Message
Description
CCRP Changed
CCRP is automatic changed.
Weather INFO
Weather information is received.
Copying
Display is capturing to file.
9－ 2
JMA-9100 Instruction Manual
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.1 FAULT FINDING
Table9-2： List of Notification
Set GYRO
Requires setting of true bearing.
TM Reset
Use care of resetting TM.
POSN Reset
Change the latitude and longitude sentence.
Table9-3： List of Target Tracking Alarms and AIS Function Alarms
メッセージ
CPA/TCPA
内
容
There is a dangerous target.
Trial
There is a dangerous target, when trial maneuver is active.
New Target
Acquisition or activation of a target in the automatic acquisition
/ activation zone.
Lost
Failure in tracking the target that has been under tracking.
Failure in receiving AIS target data for a specified time.
REF Target
Decrease in the reference target accuracy.
MAX Target
The maximum number of targets is under acquisition.
95% Capacity
Over 95% of the maximum number of targets to be tracked.
AIS Max Target
Maximum number of AIS targets.
AIS 95% Capacity
Over 95% of the maximum number of AIS targets.
AIS ACT MAX
Maximum number of AIS targets to be activated.
AIS ACT 95%
Capacity
Over 95% of the maximum number of AIS targets to be
activated.
TT (Boot)
Target tracking unit start failure.
TT (Data)
The target tracking unit is malfunctioning.
AIS (Data)
AIS: No communication or communication error.
AIS PROC (Data)
AIS Alarm ***
i.
AIS processing circuit: No communication or communication error.
AIS alarm (Up to 10 alarm messages can be displayed.).
*** is a 3-digit number which is Local Alarm No in the ALR sentence.
Table9-4： List of Route Messages and Warnings
Message
Description
Arrival
Arrive at way point.
Break Off(WPT)
Out of the way point.
Approach
Approach the route.
Cross Track Error
Go off the route.
Table9-5： List of Operational Error Messages and Warnings
Message
Description
No Position Data
Mark or line input when the latitude and longitude is invalid.
No Heading Data
Target tracking operation or TM selection when bearing data is
invalid.
Out of Range
Out of target acquisition range.
9－ 3
JMA-9100 Instruction Manual
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.1 FAULT FINDING
Table9-5： List of Operational Error Messages and Warnings
Invalid Range
TM selection due to TM-disabled range (96 nm).
Zooming in a ZOOM-disabled range (0.125 nm).
MAX Point
Tried to enter navigation information beyond the specified.
Can't Transmit
Tried to transmit within 5 second after standby or when the
transmitter-receiver has any trouble.
Invalid Data
Tried to enter any data beyond its range.
Invalid Connection
The operator set performance monitor to on without selecting
straight.
No Card
Card not detected yet.
Card Full
Card capacity insufficient.
Format Card
Unformatted card.
Invalid Card
Invalid card.
Read Failed
Read failure.
Write Failed
Write failure.
Delete Failed
Deletion failure.
Format Failed
Format failure.
Copy Failed
Copy failure.
Not Allowed
General operation error.
No Object
No object at the cursor-specified position.
Slave Mode
Operation of a menu for the scanner unit when the slave mode
is active.
Table9-6： List of Conditions Messages
Message
Description
GPS (HDOP)
The HDOP level is increased (Decrease in the GPS accuracy.).
MON Test
Performance monitor is active.
Scanner Rotating
The scanner is rotating (When transmitter is standby state.).
Battery Low
battery is weakening.
Battery Dead
The battery is dead.
Table9-7： List of Interswitch Alarms and Messages
Message
Description
Master Range CHG
The range of the own display unit has changed due to
change in the range of the master display unit.
ISW Complete
The switchover of the Interswitch ended normally.
ISW Busy
Access to the ISW menu was made during interswitching.
TXRX Standby
The scanner unit is in the standby mode.
ISW Straight
Failed in straight connection when the Interswitch
system stops operating.
ISW Standby
The Interswitch recovered normally.
ISW Time Out
Failed in switching.
ISW Error
The interswitch is disabled.
9－ 4
JMA-9100 Instruction Manual
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.1 FAULT FINDING
Table9-7： List of Interswitch Alarms and Messages
9.1.2
Pattern CHG Failed
Connection change failed.
Connection Masked
Inhibition of control / connection is set.
Master Standby
The master display unit does not transmit any signals.
ISW (Data)
No communication, data mismatched, or checksum error.
Update ISW Software
Tried to enter new TXRX function, when interswitch
software used old version.
Operation Checking
When the system is operating, the operation status (located at the upper right of
the screen) is changing pictures.
If picture freeze occurred, turn off the system and restart the system.
Operation Status
9.1.3
Fuse Checking
Melted fuses are caused by any clear cause. When a fuse is replaced, it is
necessary to check the related circuits even if there is no trouble. In checking, note
that there is some dispersion in the fusing characteristics. Table 9-8 shows a list of
fuses used in the equipment.
Table9-8： Fuse List
Location
Parts#
C u r r e n t P r o t e c t i o n Type
Rating
Circuit
AC/DC Converter F501
10A
Motor
ST6-10AN1
GYRO Interface
circuit
0.5A
GYRO
Interface
circuit
MF60NR250V0.5
F1 ～ F4
9－ 5
JMA-9100 Instruction Manual
9.2
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.2 TROUBLE SHOOTING
TROUBLE SHOOTING
As this radar equipment includes complicated circuits, it is necessary to request a
specialist engineer for repair or instructions for remedy if any circuit is defective.
There are also troubles by the following causes, which should be referred to in
checking or repair work.
１ Poor Contact in Terminal Board of Inter-Unit Cables
a. Poor contact in terminal board
b. The cable end is not fully connected, that it, contacted with earthed another
terminal.
c. Disconnected cable wire
２
Poor Contact of Connector within Unit
This radar equipment is provided with Table 9-9 standard
spares.
Table9-9： 7ZXRD0025
Name
Type/Code
Fuse
MF60NR250V0.5
Shape (mm)
In
use
Spare
Parts #
Location
12
F1 ～ F4
GYRO I/F
(5ZFGD00006)
CMJ-462E
Φ6.4
30
Fuse
ST6-10AN1
(5ZFCA00053)
F501
AC/DC Converter
NBA-5135
Φ6.35
31.8
9－ 6
JMA-9100 Instruction Manual
9.2.1
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.2 TROUBLE SHOOTING
Special Parts
NKE-2103
Table9-10： NKE-2103 (JMA-9110-6XA/6XAH、JMA-7110-6XA/6XAH)
Parts No.
Name
Type
Manufacture
Location
Code
V101
Magnetron
MAF1565N
NJRC
Scanner Unit
5VMAA00102
A101/A102
Circulator
FCX68
Toshiba
Scanner Unit
6AJRD00001
A301
Diode Limiter
NJS6930
NJRC
Scanner Unit
5ATBT00006
NKE-1125/2254
Table9-11： NKE-1125/2254
(JMA-9122-6XAH/9XA/6XAH、JMA-7122-6XA/9XA/6XAH)
Parts No.
Name
Type
Manufacture
Location
Code
V101
Magnetron
M1568BS
NJRC
Scanner Unit
5VMAA00106
A101/A102
Circulator
NJC3901M
NJRC
Scanner Unit
5AJBV00007
A301
Diode Limiter
NJS6930
NJRC
Scanner Unit
5ATBT00006
NTG-3225
Table9-12： NTG-3225
(JMA-9123-7XA/9XA、JMA-7123-7XA/9XA)
Parts No.
Name
Type
Manufacture
Location
Code
V101
Magnetron
M1568BS
NJRC
Transmitter
Receiver Unit
5VMAA00106
A101/A102
Circulator
NJC3901M
NJRC
Transmitter
Receiver Unit
5AJBV00007
A301
Diode Limiter
NJS6930
NJRC
Transmitter
Receiver Unit
5ATBT00006
NKE-1130
Table9-13： NKE-1130
(JMA-9132-SA、JMA-7132-SA)
Parts No.
Name
Type
Manufacture
Location
Code
V101
Magnetron
M1555
NJRC
Scanner Unit
5VMAA00106
A101/A102
Circulator
NJC3316
NJRC
Scanner Unit
5AJBV00007
A301
Diode Limiter
NJS6318
NJRC
Scanner Unit
5ATBT00006
NTG-3230
Table9-14： NTG-3230
(JMA-9133-SA、JMA-7133-SA)
Parts No.
Name
Type
Manufacture
Location
Code
V101
Magnetron
M1555
NJRC
Transmitter
Receiver Unit
5VMAA00104
A101
Circulator
NJC3317
NJRC
Transmitter
Receiver Unit
5AJBV00009
A301
TR Limiter
TL378A
NJRC
Transmitter
Receiver Unit
5VLAA00037
9－ 7
JMA-9100 Instruction Manual
9.2.2
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.2 TROUBLE SHOOTING
Circuit Block to be Repaired
Table9-15： Circuit Block to be Repaired (JMA-9110-6XA/6XAH)
Location
Circuit Block
Type
Remarks
SCANNER UNIT
GEARED MOTOR
7BDRD0048
DC brushless motor (common
with HS)
SCANNER UNIT
MODULATOR CIRCUIT
CME-363
Excluding Magnetron
SCANNER UNIT
RECEIVER UNIT
NRG-610
Including CAE-529-1
SCANNER UNIT
POWER SUPPLY CIRCUIT
CBD-1783
SCANNER UNIT
ENCODER
CHT-71A
SCANNER UNIT
MOTOR CONTROL POWER
SUPPLY
CBD-1779
SCANNER UNIT
FAN
7BFRD0002
RADAR
PROCESS UNIT
RADAR PROCESS CIRCUIT
MDLW11900
RADAR
PROCESS UNIT
AIS PROCESS CIRCUIT
CDC-1325
RADAR
PROCESS UNIT
ARPA PROCESS CIRCUIT
CDC-1186D
RADAR
PROCESS UNIT
GYRO I/F CIRCUIT
CMJ-462E
RADAR
PROCESS UNIT
TERMINALBOARD CIRCUIT
CQD-2097
RADAR
PROCESS UNIT
MOTHERBOARD CIRCUIT
CQC-1192
RADAR
PROCESS UNIT
FAN (RPU)
109R0612S4D13
RADAR
PROCESS UNIT
POWER SUPPLY
CBD-1661
RADAR
PROCESS UNIT
FAN (PSU)
7BFRD0006
OPERATION
UNIT
OPERATION CIRCUIT A
CCK-973
OPERATION
UNIT
OPERATION CIRCUIT B
CCK-974
OPERATION
UNIT
OPERATION CIRCUIT D
CCK-976
OPERATION
UNIT
TRACKBALL
5EZLY00003
OPERATION
UNIT
LCD PANEL
7WSRD0002A
OPERATION
UNIT
LCD OPERATION CIRCUIT
CCK-972
9－ 8
With mounting bracket
23.1-inch LCD
JMA-9100 Instruction Manual
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.2 TROUBLE SHOOTING
Table9-16： Circuit Block to be Repaired (JMA-9122-6XA/9XA)
Location
Circuit Block
Type
Remarks
SCANNER UNIT
GEARED MOTOR
MDBW10822
For 100/220VAC
SCANNER UNIT
ENCODER
CHT-71A
SCANNER UNIT
AC220V MOTOR DRIVER
7EPRD0034
For 220VAC
SCANNER UNIT
AC100V MOTOR DRIVER
7EPRD0035
For 100VAC
SCANNER UNIT
PERFORMANCE MONITOR
NJU-85
SCANNER UNIT
HEATER CONTROL PART
CHG-216
SCANNER UNIT
BREAK CIRCUIT
CFA-253
SCANNER UNIT
BREAK CONTROL CIRCUIT
CCB-655
SCANNER UNIT
BREAK CIRCUIT A
CFA-259
SCANNER UNIT
BREAK CIRCUIT B
CFA-260
SCANNER UNIT
T/R CONTROL CIRCUIT
CMC-1205R
SCANNER UNIT
MODULATOR UNIT
NMA-550
SCANNER UNIT
MODULATOR CIRCUIT
CPA-264
SCANNER UNIT
RECEIVER UNIT
NRG-162A
SCANNER UNIT
POWER SUPPLY CIRCUIT
CBD-1682A
SCANNER UNIT
RELAY FILTER CIRCUIT
CSC-656
SCANNER UNIT
FAN
7BFRD0002
RADAR PROCESS UNIT
RADAR PROCESS CIRCUIT
MDLW11900
RADAR PROCESS UNIT
AIS PROCESS CIRCUIT
CDC-1325
RADAR PROCESS UNIT
ARPA PROCESS CIRCUIT
CDC-1186D
RADAR PROCESS UNIT
GYRO I/F CIRCUIT
CMJ-462E
RADAR PROCESS UNIT
TERMINALBOARD CIRCUIT
CQD-2097
RADAR PROCESS UNIT
MOTHERBOARD CIRCUIT
CQC-1192
RADAR PROCESS UNIT
FAN (RPU)
109R0612S4D13
RADAR PROCESS UNIT
POWER SUPPLY
CBD-1661
RADAR PROCESS UNIT
FAN (PSU)
7BFRD0006
OPERATION UNIT
OPERATION CIRCUIT A
CCK-973
OPERATION UNIT
OPERATION CIRCUIT B
CCK-974
OPERATION UNIT
OPERATION CIRCUIT D
CCK-976
OPERATION UNIT
TRACKBALL
5EZLY00003
MONITOR UNIT
LCD PANEL
7WSRD0002A
MONITOR UNIT
LCD OPERATION CIRCUIT
CCK-972
9－ 9
Option (AC100V)
Including CPA-264
Including CMB-404
Including CFR-229
Excluding Magnetron
Including CMA-866A
With mounting bracket
23.1-inch LCD
JMA-9100 Instruction Manual
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.2 TROUBLE SHOOTING
Table9-17： Circuit Block to be Repaired (JMA-9122-6XAH)
Location
Circuit Block
Type
Remarks
SCANNER UNIT
GEARED MOTOR
7BDRD0045A
For 100/220VAC
SCANNER UNIT
ENCODER
CHT-71A
SCANNER UNIT
MOTOR CONTROL POWER
CIRCUIT
CBD-1779
SCANNER UNIT
BREAK CIRCUIT
CFA-257
SCANNER UNIT
PERFORMANCE MONITOR
NJU-85
SCANNER UNIT
HEATER CONTROL PART
CHG-216
SCANNER UNIT
POWER SUPPLY CIRCUIT
CBD-1682A
SCANNER UNIT
T/R CONTROL CIRCUIT
CMC-1205R
SCANNER UNIT
MODULATOR UNIT
NMA-550
SCANNER UNIT
MODULATOR CIRCUIT
CPA-264
SCANNER UNIT
RECEIVER UNIT
NRG-162A
SCANNER UNIT
FAN
7BFRD0002
RADAR PROCESS UNIT
RADAR PROCESS CIRCUIT
MDLW11900
RADAR PROCESS UNIT
AIS PROCESS CIRCUIT
CDC-1325
RADAR PROCESS UNIT
ARPA PROCESS CIRCUIT
CDC-1186D
RADAR PROCESS UNIT
GYRO I/F CIRCUIT
CMJ-462E
RADAR PROCESS UNIT
TERMINALBOARD CIRCUIT
CQD-2097
RADAR PROCESS UNIT
MOTHERBOARD CIRCUIT
CQC-1192
RADAR PROCESS UNIT
FAN (RPU)
109R0612S4D13
RADAR PROCESS UNIT
POWER SUPPLY
CBD-1661
RADAR PROCESS UNIT
FAN (PSU)
7BFRD0006
OPERATION UNIT
OPERATION CIRCUIT A
CCK-973
OPERATION UNIT
OPERATION CIRCUIT B
CCK-974
OPERATION UNIT
OPERATION CIRCUIT D
CCK-976
OPERATION UNIT
TRACKBALL
5EZLY00003
MONITOR UNIT
LCD PANEL
7WSRD0002A
MONITOR UNIT
LCD OPERATION CIRCUIT
CCK-972
9－ 10
Option (AC100V)
Including CPA-264
Including CMB-404
Including CFR-229
Excluding Magnetron
Including CMA-866A
With mounting bracket
23.1-inch LCD
JMA-9100 Instruction Manual
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.2 TROUBLE SHOOTING
Table9-18： Circuit Block to be Repaired (JMA-9123-7XA/9XA)
Location
Circuit Block
Type
Remarks
SCANNER UNIT
GEARED MOTOR
MDBW10822
For 100/220VAC
SCANNER UNIT
ENCODER
CHT-71A
SCANNER UNIT
AC220V MOTOR DRIVER
7EPRD0034
For 220VAC
SCANNER UNIT
AC100V MOTOR DRIVER
7EPRD0035
For 100VAC
SCANNER UNIT
PERFORMANCE MONITOR
NJU-85
SCANNER UNIT
HEATER CONTROL PART
CHG-216
SCANNER UNIT
BREAK CIRCUIT
CFA-253
SCANNER UNIT
BREAK CONTROL CIRCUIT
CCB-655
SCANNER UNIT
BREAK CIRCUIT A
CFA-259
SCANNER UNIT
BREAK CIRCUIT B
CFA-260
TRANSMITTER
RECEIVER UNIT
T/R CONTROL CIRCUIT
CMC-1205R
TRANSMITTER
RECEIVER UNIT
MODULATOR UNIT
NMA-552
TRANSMITTER
RECEIVER UNIT
MODULATOR CIRCUIT
CPA-264
TRANSMITTER
RECEIVER UNIT
RECEIVER UNIT
NRG-162A
TRANSMITTER
RECEIVER UNIT
POWER SUPPLY CIRCUIT
CBD-1682A
TRANSMITTER
RECEIVER UNIT
RELAY FILTER CIRCUIT
CSC-656
RADAR PROCESS UNIT
RADAR PROCESS CIRCUIT
MDLW11900
RADAR PROCESS UNIT
AIS PROCESS CIRCUIT
CDC-1325
RADAR PROCESS UNIT
ARPA PROCESS CIRCUIT
CDC-1186D
RADAR PROCESS UNIT
GYRO I/F CIRCUIT
CMJ-462E
RADAR PROCESS UNIT
TERMINALBOARD CIRCUIT
CQD-2097
RADAR PROCESS UNIT
MOTHERBOARD CIRCUIT
CQC-1192
RADAR PROCESS UNIT
FAN (RPU)
109R0612S4D13
RADAR PROCESS UNIT
POWER SUPPLY
CBD-1661
RADAR PROCESS UNIT
FAN (PSU)
7BFRD0006
OPERATION UNIT
OPERATION CIRCUIT A
CCK-973
OPERATION UNIT
OPERATION CIRCUIT B
CCK-974
OPERATION UNIT
OPERATION CIRCUIT D
CCK-976
OPERATION UNIT
TRACKBALL
5EZLY00003
MONITOR UNIT
LCD PANEL
7WSRD0002A
MONITOR UNIT
LCD OPERATION CIRCUIT
CCK-972
9－ 11
Option (AC100V)
Including CPA-264
Including CMB-405
Including CFR-229
Excluding Magnetron
Including CMA-866A
With mounting bracket
23.1-inch LCD
JMA-9100 Instruction Manual
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.2 TROUBLE SHOOTING
Table9-19： Circuit Block to be Repaired (JMA-9132-SA)
Location
Circuit Block
Type
Remarks
SCANNER UNIT
GEARED MOTOR
MDBW10823
For 100/220VAC
SCANNER UNIT
ENCODER
CHT-71A1
SCANNER UNIT
AC220V MOTOR DRIVER
7EPRD0034
For 220VAC
SCANNER UNIT
AC100V MOTOR DRIVER
7EPRD0035
For 100VAC
SCANNER UNIT
PERFORMANCE MONITOR
NJU-84
SCANNER UNIT
HEATER CONTROL PART
CHG-215
SCANNER UNIT
BREAK CIRCUIT
CFA-255
SCANNER UNIT
BREAK CONTROL CIRCUIT
CCB-655
SCANNER UNIT
BREAK CIRCUIT A
CFA-261
SCANNER UNIT
BREAK CIRCUIT B
CFA-262
SCANNER UNIT
T/R CONTROL CIRCUIT
CMC-1205R
SCANNER UNIT
MODULATOR UNIT
NMA-551
SCANNER UNIT
MODULATOR CIRCUIT
CPA-264
SCANNER UNIT
RECEIVER UNIT
NRG-229
SCANNER UNIT
POWER SUPPLY CIRCUIT
CBD-1682A
SCANNER UNIT
RELAY FILTER CIRCUIT
CSC-656
SCANNER UNIT
FAN
7BFRD0002
RADAR PROCESS UNIT
RADAR PROCESS CIRCUIT
MDLW11900
RADAR PROCESS UNIT
AIS PROCESS CIRCUIT
CDC-1325
RADAR PROCESS UNIT
ARPA PROCESS CIRCUIT
CDC-1186D
RADAR PROCESS UNIT
GYRO I/F CIRCUIT
CMJ-462E
RADAR PROCESS UNIT
TERMINALBOARD CIRCUIT
CQD-2097
RADAR PROCESS UNIT
MOTHERBOARD CIRCUIT
CQC-1192
RADAR PROCESS UNIT
FAN (RPU)
109R0612S4D13
RADAR PROCESS UNIT
POWER SUPPLY
CBD-1661
RADAR PROCESS UNIT
FAN (PSU)
7BFRD0006
OPERATION UNIT
OPERATION CIRCUIT A
CCK-973
OPERATION UNIT
OPERATION CIRCUIT B
CCK-974
OPERATION UNIT
OPERATION CIRCUIT D
CCK-976
OPERATION UNIT
TRACKBALL
5EZLY00003
MONITOR UNIT
LCD PANEL
7WSRD0002A
MONITOR UNIT
LCD OPERATION CIRCUIT
CCK-972
9－ 12
Option (AC100V)
Including CPA-264
Including CMB-406
Including CFR-229
Exluding Magnetron
With mounting bracket
23.1-inch LCD
JMA-9100 Instruction Manual
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.2 TROUBLE SHOOTING
Table9-20： Circuit Block to be Repaired (JMA-9133-SA)
Location
Circuit Block
Type
Remarks
SCANNER UNIT
GEARED MOTOR
MDBW10823
For 100/220VAC
SCANNER UNIT
ENCODER
CHT-71A1
SCANNER UNIT
AC220V MOTOR DRIVER
7EPRD0034
For 220VAC
SCANNER UNIT
AC100V MOTOR DRIVER
7EPRD0035
For 100VAC
SCANNER UNIT
PERFORMANCE MONITOR
NJU-84
SCANNER UNIT
HEATER CONTROL PART
CHG-215
SCANNER UNIT
BREAK CIRCUIT
CFA-255
SCANNER UNIT
BREAK CONTROL CIRCUIT
CCB-655
SCANNER UNIT
BREAK CIRCUIT A
CFA-261
SCANNER UNIT
BREAK CIRCUIT B
CFA-262
TRANSMITTER
RECEIVER UNIT
T/R CONTROL CIRCUIT
CMC-1205R
TRANSMITTER
RECEIVER UNIT
MODULATOR UNIT
NMA-553
TRANSMITTER
RECEIVER UNIT
MODULATOR CIRCUIT
CPA-264
TRANSMITTER
RECEIVER UNIT
RECEIVER UNIT
NRG-229
TRANSMITTER
RECEIVER UNIT
POWER SUPPLY CIRCUIT
CBD-1682A
TRANSMITTER
RECEIVER UNIT
RELAY FILTER CIRCUIT
CSC-656
RADAR PROCESS UNIT
RADAR PROCESS CIRCUIT
MDLW11900
RADAR PROCESS UNIT
AIS PROCESS CIRCUIT
CDC-1325
RADAR PROCESS UNIT
ARPA PROCESS CIRCUIT
CDC-1186D
RADAR PROCESS UNIT
GYRO I/F CIRCUIT
CMJ-462E
RADAR PROCESS UNIT
TERMINALBOARD CIRCUIT
CQD-2097
RADAR PROCESS UNIT
MOTHERBOARD CIRCUIT
CQC-1192
RADAR PROCESS UNIT
FAN (RPU)
109R0612S4D13
RADAR PROCESS UNIT
POWER SUPPLY
CBD-1661
RADAR PROCESS UNIT
FAN (PSU)
7BFRD0006
OPERATION UNIT
OPERATION CIRCUIT A
CCK-973
OPERATION UNIT
OPERATION CIRCUIT B
CCK-974
OPERATION UNIT
OPERATION CIRCUIT D
CCK-976
OPERATION UNIT
TRACKBALL
5EZLY00003
MONITOR UNIT
LCD PANEL
7WSRD0002A
MONITOR UNIT
LCD OPERATION CIRCUIT
CCK-972
9－ 13
Option (AC100V)
Including CPA-264
Including CMB-407
Including CFR-229
Exluding Magnetron
With mounting bracket
23.1-inch LCD
JMA-9100 Instruction Manual
9.3
9.3.1
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.3 AFTER-SALES SERVICE
AFTER-SALES SERVICE
Keeping period of maintenance parts
Keeping period of maintenance parts is ten years from the production is
discontinued.
9.3.2
When you Request for Repair
If you suppose the product may be out of order, read the description in Section 9
carefully and check the suspected point again.
If it is still out of order, you are recommended to stop operation of the equipment
and consult with the dealer from whom you purchased the product, or our branch
office in your country or district, the sales department in our main office in Tokyo.
Repair within the Warranty Period
If any failure occurs in the product during its normal operation in accordance with
the instruction manual, the dealer or JRC will repair free of charge. In case that
any failure is caused due to misuse, faulty operation, negligence or force major
such as natural disaster and fire, the product will be repaired with charges.
Repair after the Warranty Period
If any defective function of the product is recoverable by repair, the repair of it
will be made at your own charge upon your request.
Necessary Information for Repair
• Product name, model, manufacturing date and serial number
• Trouble conditions (as detailed as possible. Refer to "Radar Failure Check
List" on page 9-15
• Name of company/organization, address and telephone number
9.3.3
Recommended Maintenance
The performance of the product may deteriorate due to the secular change of the
parts used in it, though such deterioration depends upon the conditions of
operation. So checkup and maintenance is recommendable for the product in
addition to your daily care.
For maintenance, consult with the near-by dealer or our sales department.Such
maintenance will be made with charges.
For further details of after-sale service, contact the JRC Offices.
9－ 14
JMA-9100 Instruction Manual
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.3 AFTER-SALES SERVICE
Radar Failure Check List
When placing an order for repair of the product, it is requested that you could
confirm the check items and fill the results and sent the sheet to our contact.
If there is any unclear items, contact the ship on which the product is
installed, and give the correct information on the product.
Ship name:
Radar general model name
i.
Phone:
Fax:
:JMA-
Serial No. :
Write the full model name correctly
Check the following items in the order of the number, and check the applicable
answer between YES or NO.
If the item cannot be determined as YES or NO, explain in detail in the item (18),
others.
No.
Check Item
Result
(1)
Power can be turned on. (The lamp on the Operation unit is lit)
YES
NO
A few minutes after powering-on, it will become standby status.
YES
NO
(2)
(3)i
When powering-on (or TX ON), LCD monitor something is lit.
YES
NO
(4)
i,ii
The antenna rotates at the transmission (TX) ON.
YES
NO
(5)
i,ii
Current is supplied to the magnetron. (Refer to the instruction manual)
YES
NO
(6)ii
Turning is enabled. (Check with the range of 6 NM or more)
YES
NO
(7)
ii
Fixed marker is displayed.
YES
NO
(8)
ii
VRM is displayed.
YES
NO
While noise is displayed while set at SEA and RAIN minimum, GAIN YES
maximum, IR-OFF and range 48 NM.
NO
Target reflection echo is displayed.
YES
NO
Sensitivity of reflection echo is normal.
YES
NO
(9)ii
(10)ii
(11)
ii
(12)ii
EBL is displayed.
YES
NO
(13)
ii
Cursor mark moves.
YES
NO
(14)
ii,iii
GYRO course can be set and normally displayed.
YES
NO
(15)ii,iii
LOG speed can be normally displayed.
YES
NO
(16)
ii
Target tracking function works normally.
YES
NO
(17)
ii,iii
If equipped with an interswitch, when switching from the straight mode (II) to YES
(X), the failures (items marked NO) in the above (1) to (16), are switched over
to the other unit.
NO
（18） Others (Error message, etc. )
i.
If result is NO, then check the fuse. (Refer to Section 9.1.2 "Operation Checking" and Section 9.2 "TROUBLE
SHOOTING")
ii. Check these items while transmission is ON.
iii. Functions mentioned in the items (14), (15) and (17) may be optional, answer is not necessary.
9－ 15
JMA-9100 Instruction Manual
9.TROUBLE SHOOTING AND AFTER-SALES SERVICE
9－ 16
9.3 AFTER-SALES SERVICE
SECTION 10
DISPOSAL
DISPOSAL
10.1
DISPOSAL OF THE UNIT ....................................................................10-1
10.2
DISPOSAL OF USED BATTERIES .....................................................10-1
10.3
DISPOSAL OF USED MAGNETRON ..................................................10-2
10.4
DISPOSAL OF TR-TUBE .....................................................................10-2
10.5
ABOUT THE CHINA ROHS .................................................................10-3
JMA-9100 Instruction Manual
10.1
10.DISPOSAL
10.1 DISPOSAL OF THE UNIT
DISPOSAL OF THE UNIT
When disposing of this unit, be sure to follow the local laws and regulations for
the place of disposal.
10.2
DISPOSAL OF USED BATTERIES
When disposing of used lithium batteries, be sure to
insulate the batteries by taping the + - terminals.
Otherwise, heat generation, explosion or a fire may
occur.
In this unit, Lithium batteries are used for the following parts:
Radar Processing circuit (CDC-1324): BT1 (Maxell: CR2032)
• Do not store used lithium batteries. Dispose of them in accordance with
regulations of local government.
• When disposing of used lithium batteries be sure to insulate the batteries by
taping the + - terminals. For disposal of batteries, be sure to follow the local
laws and regulations. For detail, consult with the dealer you purchased the
product our business office, or local government.
10－ 1
10
JMA-9100 Instruction Manual
10.3
10.DISPOSAL
10.3 DISPOSAL OF USED MAGNETRON
DISPOSAL OF USED MAGNETRON
Magnetron is used in the Scanner （NKE－ 2103/2254/1125/1130）and
Transmitter Receiver Unit (NTG-3225/3230).
• When the magnetron is replaced with a new one, return the used magnetron to
our dealer or business office.
For detail, consult with our dealer or business office.
10.4
DISPOSAL OF TR-TUBE
In the case that either mark shown in Fig 10-1 is on the expired TR-tube,
Radioisotopes are in the TR-tube.
• Disposal of TR-tube with these marks must be done in accordance with the
laws and regulations of the pertaining country. For detail, consult with our
dealer or business office.
• Radiation from TR-tube has no effect on the human body.
• Don't take apart TR-tube.
Fig 10-1: Radioisotopes Marks
10－ 2
10
JMA-9100 Instruction Manual
10.5
10.DISPOSAL
10.5 ABOUT THE CHINA ROHS
ABOUT THE CHINA ROHS
有毒有害物质或元素的名称及含量
(Names & Content of toxic and hazardous substances or elements）
形式名(Type): JMA-9100 Series, JMA-7100Series
名称(Name): RADAR
有毒有害物质或元素
部件名称
(Part name)
(Toxic and Hazardous Substances and Elements)
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr6+)
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
雷达天线单元
(Scanner Unit)
×
×
○
×
×
×
收发信单元
(Transmitter-receiver Unit)
×
×
×
×
×
×
主船内装置 (Inboard Unit)
・显示装置 (Display Unit)
・键盘装置 (OperationUnit)
・信号处理装置
(RADAR Process Unit)
×
×
×
×
×
×
外部设备 (Peripherals)
・选择 (Options)
・电线类 (Cables)
・手册 (Documennts)
×
×
×
×
×
×
○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11306-2006 标准规定的限量要求以下。
(Indicates that this toxic, or hazardous substance contained in all of the homogeneous materials for this
part is below the requirement in SJ/T11363-2006.)
×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006 标准规定的限量要求。
(Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials
used for this part is above the limit requirement in SJ/T 11363-2006.)
10
10－ 3
JMA-9100 Instruction Manual
10.DISPOSAL
10.5 ABOUT THE CHINA ROHS
10－ 4
SECTION 11
SPECIFICATION
SPECIFICATION
11.1
JMA-9133-SA TYPE RADAR ...............................................................11-1
11.2
JMA-9132-SA TYPE RADAR ............................................................... 11-2
11.3
JMA-9123-7XA/9XA TYPE RADAR ....................................................11-3
11.4
JMA-9122-6XA/9XA TYPE RADAR ....................................................11-4
11.5
JMA-9122-6XAH TYPE RADAR .........................................................11-5
11.6
JMA-9110-6XA TYPE RADAR ............................................................11-6
11.7
JMA-9110-6XAH TYPE RADAR .........................................................11-7
11.8
SCANNER UNIT (NKE-1139) ...............................................................11-8
11.9
SCANNER UNIT (NKE-1130) ...............................................................11-9
11.10 SCANNER UNIT (NKE-1129-7/9) ......................................................11-10
11.11 SCANNER UNIT (NKE-1125-6/9) .......................................................11-11
11.12 SCANNER UNIT (NKE-2254-6HS) .....................................................11-12
11.13 SCANNER UNIT (NKE-2103-6) ..........................................................11-13
11.14 SCANNER UNIT (NKE-2103-6HS) .....................................................11-14
11.15 TRANSMITTER RECEIVER UNIT (NTG-3230) .................................11-15
11.16 TRANSMITTER RECEIVER UNIT (NTG-3225) .................................11-16
11.17 DISPLAY UNIT (NCD-4990) ...............................................................11-17
11.18
11.19
11.20
11.21
11.22
Target Tracking Function .................................................................11-20
AIS FUNCTION ...................................................................................11-21
PERFORMANCE MONITOR (NJU-84) ..............................................11-22
PERFORMANCE MONITOR (NJU-85) ..............................................11-22
AC-DC CONVERTER (NBA-5135) .....................................................11-22
JMA-9100 Instruction Manual
11.1
11.SPECIFICATION
11.1 JMA-9133-SA TYPE RADAR
JMA-9133-SA TYPE RADAR
GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125、0.25、0.5、0.75、1.5、3、6、12、24、48、96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70 ℃ )
Other Unit
-15 to +55 ℃
Relative humidity 93% at +40 ℃
Vibration 2 to 13.2Hz
Amplitude
+/-1mm +/-10%
13.2 to 100Hz Acceleration
7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.400VA typical
Approx. 2000VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-1139)
See 11.8
TRANSMITTER RECEIVER UNIT (NTG-3230)
See 11.15
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR (NJU-84)
See 11.20
OPTION
Scanner with Deicing Heater NKE-1139-D (Only heater collar)
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT to
TRANSMITTER RECEIVER UNIT
30m
DISPLAY UNIT to
TRANSMITTER RECEIVER UNIT
35m
11
SAFE DISTANCE FOR STANDARD COMPASS
SCANNER UNIT 1.4m
TRANSMITTER RECEIVER UNIT 3.9m
DISPLAY UNIT 4.0m
11－ 1
JMA-9100 Instruction Manual
11.2
11.SPECIFICATION
11.2 JMA-9132-SA TYPE RADAR
JMA-9132-SA TYPE RADAR
GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70 ℃ )
Other Unit
-15 to +55 ℃
Relative humidity 93% at +40 ℃
Vibration 2 to 13.2Hz
Amplitude
+/-1mm +/-10%
13.2 to 100Hz Acceleration
7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.400VA typical
Approx. 2000VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-1130)
See 11.9
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR (NJU-84)
See 11.20
OPTION
Scanner with Deicing Heater NKE-1139-D (Only heater collar)
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT to
TRANSMITTER RECEIVER UNIT
65m
SAFE DISTANCE FOR STANDARD COMPASS
SCANNER UNIT 5.1m
DISPLAY UNIT 4.0m
11－ 2
JMA-9100 Instruction Manual
11.3
11.SPECIFICATION
11.3 JMA-9123-7XA/9XA TYPE RADAR
JMA-9123-7XA/9XA TYPE RADAR
GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70 ℃ )
Other Unit
-15 to +55 ℃
Relative humidity 93% at +40 ℃
Vibration 2 to 13.2Hz
Amplitude
+/-1mm +/-10%
13.2 to 100Hz Acceleration
7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.350VA typical
Approx. 1700VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-1129-7/9)
See 11.10
TRANSMITTER RECEIVER UNIT (NTG-3225)
See 11.16
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR (NJU-85)
See 11.21
OPTION
Scanner with Deicing Heater NKE-1139-D (Only heater collar)
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT to
TRANSMITTER RECEIVER UNIT
30m
DISPLAY UNIT to
TRANSMITTER RECEIVER UNIT
35m
11
SAFE DISTANCE FOR STANDARD COMPASS
SCANNER UNIT 1.05m
TRANSMITTER RECEIVER UNIT 2.8m
DISPLAY UNIT 4.0m
11－ 3
JMA-9100 Instruction Manual
11.4
11.SPECIFICATION
11.4 JMA-9122-6XA/9XA TYPE RADAR
JMA-9122-6XA/9XA TYPE RADAR
GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70 ℃ )
Other Unit
-15 to +55 ℃
Relative humidity 93% at +40 ℃
Vibration 2 to 13.2Hz
Amplitude
+/-1mm +/-10%
13.2 to 100Hz Acceleration
7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.350VA typical
Approx. 1700VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-1125-6/9)
See 11.11
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR (NJU-85)
See 11.21
OPTION
Scanner with Deicing Heater NKE-1139-D (Only heater collar)
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT to
TRANSMITTER RECEIVER UNIT
65m
SAFE DISTANCE FOR STANDARD COMPASS
SCANNER UNIT 2.4m
DISPLAY UNIT 4.0m
11－ 4
JMA-9100 Instruction Manual
11.5
11.SPECIFICATION
11.5 JMA-9122-6XAH TYPE RADAR
JMA-9122-6XAH TYPE RADAR
GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70 ℃ )
Other Unit
-15 to +55 ℃
Relative humidity 93% at +40 ℃
Vibration 2 to 13.2Hz
Amplitude
+/-1mm +/-10%
13.2 to 100Hz Acceleration
7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.350VA typical
Approx. 1000VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-2254-6HS)
See 11.11
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR (NJU-85)
See 11.21
AC-DC CONVERTER (NBA-5135)
See 11.22
OPTION
Scanner with Deicing Heater None
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT to
TRANSMITTER RECEIVER UNIT
65m
11
SAFE DISTANCE FOR STANDARD COMPASS
SCANNER UNIT 2.4m
DISPLAY UNIT 4.0m
11－ 5
JMA-9100 Instruction Manual
11.6
11.SPECIFICATION
11.6 JMA-9110-6XA TYPE RADAR
JMA-9110-6XA TYPE RADAR
GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70 ℃ )
Other Unit
-15 to +55 ℃
Relative humidity 93% at +40 ℃
Vibration 2 to 13.2Hz
Amplitude
+/-1mm +/-10%
13.2 to 100Hz Acceleration
7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.350VA typical
Approx. 1000VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-2103-6)
See 11.13
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR
(NJU-85)
See 11.21
AC-DC CONVERTER (NBA5135)
See 11.22
OPTION
Scanner with Deicing Heater None
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT to
TRANSMITTER RECEIVER UNIT
65m
SAFE DISTANCE FOR
STANDARD COMPASS
SCANNER UNIT 2.4m
DISPLAY UNIT 4.0m
11－ 6
JMA-9100 Instruction Manual
11.7
11.SPECIFICATION
11.7 JMA-9110-6XAH TYPE RADAR
JMA-9110-6XAH TYPE RADAR
GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70 ℃ )
Other Unit
-15 to +55 ℃
Relative humidity 93% at +40 ℃
Vibration 2 to 13.2Hz
Amplitude
+/-1mm +/-10%
13.2 to 100Hz Acceleration
7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.350VA typical
Approx. 1000VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-2103-6HS)
See 11.14
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR (NJU-85)
See 11.21
AC-DC CONVERTER (NBA-5135)
See 11.22
OPTION
Scanner with Deicing Heater None
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT～ DISPLAY 65m
UNIT
11
SAFE DISTANCE FOR STANDARD COMPASS
SCANNER UNIT 2.4m
DISPLAY UNIT 4.0m
11－ 7
JMA-9100 Instruction Manual
11.8
SCANNER UNIT
11.SPECIFICATION
11.8 SCANNER UNIT (NKE-1139)
SCANNER UNIT (NKE-1139)
NKE-1139
Dimension Height 791 x Swing Circle 4000 (mm)
Mass Approx.150kg
Polarization Horizontal
Directional Characteristics
Horizontal beam width : 1.9°
Vertical beam width : 25°
Side lobe Level : below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor AC100 - 115V、50/60Hz、1φ or
AC220 - 240V、50/60Hz、1φ
Maximum Wind Velocity 51.5m/s (100knots)
11－ 8
JMA-9100 Instruction Manual
11.9
11.SPECIFICATION
11.9 SCANNER UNIT (NKE-1130)
SCANNER UNIT (NKE-1130)
SCANNER UNIT
NKE-1130
Dimension Height 791 x Swing Circle 4000 (mm)
Mass Approx.180kg
Polarization Horizontal
Directional Characteristics
Horizontal beam width : 1.9°
Vertical beam width : 25°
Side lobe Level : below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor AC100 - 115V、50/60Hz、1φ or
AC220 - 240V、50/60Hz、1φ
Maximum Wind Velocity 51.5m/s (100knots)
Transmitting Frequency 3050 ± 20MHz
Transmitting Power 30kW
Transmitting Tube Magnetron[M1555]
TX Pulse width / Repetition SP1：0.07μs/2250Hz
Frequency MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2/MP3
3NM ：MP1/MP2/MP3/LP1
6NM ：MP1/MP2/MP3/LP1/LP2
12NM ：MP1/MP2/MP3/LP1/LP2
24NM ：MP3/LP1/LP2
48NM ：LP2
96NM ：LP3
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier
Intermediate Frequency
Band Width
Gain
Amplifying Characteristics
60MHz
25/8/3MHz
more than 90dB
Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO
11
11－ 9
JMA-9100 Instruction Manual
11.10
SCANNER UNIT
11.SPECIFICATION
11.10 SCANNER UNIT (NKE-1129-7/9)
SCANNER UNIT (NKE-1129-7/9)
NKE-1129-7/9
Dimension 7ft
9ft
Mass 7ft
9ft
Height 536 x Swing Circle 2270 (mm)
Height 536 x Swing Circle 2825 (mm)
Approx.51kg
Approx.53kg
Polarization Horizontal
Directional Characteristics
Horizontal beam width :
Vertical beam width :
Side lobe Level :
1.0° (7ft)
0.8° (9ft)
20°
below -26dB (within +/-10°)
below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor AC100 - 115V、50/60Hz、1φ or
AC220 - 240V、50/60Hz、1φ
Maximum Wind Velocity 51.5m/s (100knots)
11 －10
JMA-9100 Instruction Manual
11.11
SCANNER UNIT
11.SPECIFICATION
11.11 SCANNER UNIT (NKE-1125-6/9)
SCANNER UNIT (NKE-1125-6/9)
NKE-1125-6/9
Dimension 6ft
9ft
Mass 6ft
9ft
Height 536 x Swing Circle 1910 (mm)
Height 536 x Swing Circle 2825 (mm)
Approx. 55kg
Approx. 60kg
Polarization Horizontal
Directional Characteristics
Horizontal beam width :
Vertical beam width :
Side lobe Level :
1.2° (6ft)
0.8° (9ft)
20°
below -26dB (within +/-10°)
below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor AC100 - 115V、50/60Hz、1φ or
AC220 - 240V、50/60Hz、1φ
Maximum Wind Velocity 51.5m/s (100knots)
Transmitting Frequency 9410 ± 30MHz
Transmitting Power 25kW
Transmitting Tube Magnetron[M1568BS]
TX Pulse width / Repetition SP1：0.07μs/2250Hz
Frequency MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2/MP3
3NM ：MP1/MP2/MP3/LP1
6NM ：MP1/MP2/MP3/LP1/LP2
12NM ：MP1/MP2/MP3/LP1/LP2
24NM ：MP3/LP1/LP2
48NM ：LP2
96NM ：LP3
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier
Intermediate Frequency
Band Width
Gain
Amplifying Characteristics
60MHz
25/8/3MHz
more than 90dB
Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO
11
11－ 11
JMA-9100 Instruction Manual
11.12
SCANNER UNIT
11.SPECIFICATION
11.12 SCANNER UNIT (NKE-2254-6HS)
SCANNER UNIT (NKE-2254-6HS)
NKE-2254-6HS
Dimension Height 536 x Swing Circle 1910 (mm)
Mass Approx. 55kg
Polarization Horizontal
Directional Characteristics
Horizontal beam width : 1.2°
Vertical beam width : 20°
Side lobe Level : below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor DC24V
Maximum Wind Velocity 51.5m/s (100knots)
Transmitting Frequency 9410 ± 30MHz
Transmitting Power 25kW
Transmitting Tube Magnetron[M1568BS]
TX Pulse width / Repetition SP1：0.07μs/2250Hz
Frequency MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2/MP3
3NM ：MP1/MP2/MP3/LP1
6NM ：MP1/MP2/MP3/LP1/LP2
12NM ：MP1/MP2/MP3/LP1/LP2
24NM ：MP3/LP1/LP2
48NM ：LP2
96NM ：LP3
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier
Intermediate Frequency
Band Width
Gain
Amplifying Characteristics
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO
11 －12
60MHz
25/8/3MHz
more than 90dB
Logarithmic Amplifier
JMA-9100 Instruction Manual
11.13
SCANNER UNIT
11.SPECIFICATION
11.13 SCANNER UNIT (NKE-2103-6)
SCANNER UNIT (NKE-2103-6)
NKE-2103-6HS
Dimension Height 458 x Swing Circle 1910 (mm)
Mass Approx. 40kg
Polarization Horizontal
Directional Characteristics
Horizontal beam width : 1.2°
Vertical beam width : 20°
Side lobe Level : below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor DC24V
Maximum Wind Velocity 51.5m/s (100knots)
Transmitting Frequency 9410 ± 30MHz
Transmitting Power 10kW
Transmitting Tube Magnetron[MAF1565N]
TX Pulse width / Repetition SP1：0.08μs/2250Hz
Frequency MP1：0.25μs/1700Hz MP2：0.5μs/1200Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2
3NM ：MP1/MP2LP1
6NM ：MP1/MP2/LP1/LP2
12NM ：MP1/MP2/LP1/LP2
24NM ：MP2/LP1/LP2
48NM ：LP2
96NM ：LP2
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier
Intermediate Frequency
Band Width
Gain
Amplifying Characteristics
60MHz
20/6/3MHz
more than 90dB
Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO
11
11 －13
JMA-9100 Instruction Manual
11.14
SCANNER UNIT
11.SPECIFICATION
11.14 SCANNER UNIT (NKE-2103-6HS)
SCANNER UNIT (NKE-2103-6HS)
NKE-2103-6HS
Dimension Height 458 x Swing Circle 1910 (mm)
Mass Approx. 40kg
Polarization Horizontal
Directional Characteristics
Horizontal beam width : 1.2°
Vertical beam width : 20°
Side lobe Level : below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor DC24V
Maximum Wind Velocity 51.5m/s (100knots)
Transmitting Frequency 9410 ± 30MHz
Transmitting Power 10kW
Transmitting Tube Magnetron[MAF1565N]
TX Pulse width / Repetition SP1：0.08μs/2250Hz
Frequency MP1：0.25μs/1700Hz MP2：0.5μs/1200Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2
3NM ：MP1/MP2LP1
6NM ：MP1/MP2/LP1/LP2
12NM ：MP1/MP2/LP1/LP2
24NM ：MP2/LP1/LP2
48NM ：LP2
96NM ：LP2
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier
Intermediate Frequency
Band Width
Gain
Amplifying Characteristics
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO
11 －14
60MHz
20/6/3MHz
more than 90dB
Logarithmic Amplifier
JMA-9100 Instruction Manual
11.15
11.SPECIFICATION
11.15 TRANSMITTER RECEIVER UNIT (NTG-3230)
TRANSMITTER RECEIVER UNIT
(NTG-3230)
SCANNER UNIT
NTG-3230
Dimension :Width 615 x Depth 365 x Height 615 (mm)
構造 Wall Mount, Drip Proof
Mass Approx.33kg
Transmitting Frequency 3050 ± 20MHz
Transmitting Power 30kW
Transmitting Tube Magnetron [M1555]
TX Pulse width / Repetition SP1：0.07μs/2250Hz
Frequency MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2/MP3
3NM ：MP1/MP2/MP3/LP1
6NM ：MP1/MP2/MP3/LP1/LP2
12NM ：MP1/MP2/MP3/LP1/LP2
24NM ：MP3/LP1/LP2
48NM ：LP2
96NM ：LP3
Modulator Solid State Modulator Circuit
Duplexer Circulator + TRHPL
Front End Module Built-in
Intermediate Frequency Amplifier
Intermediate Frequency
Band Width
Gain
Amplifying Characteristics
60MHz
25/8/3MHz
more than 90dB
Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO
11
11 －15
JMA-9100 Instruction Manual
11.16
11.SPECIFICATION
11.16 TRANSMITTER RECEIVER UNIT (NTG-3225)
TRANSMITTER RECEIVER UNIT
(NTG-3225)
SCANNER UNIT
NTG-3225
Dimension :Width 460 x Depth 227 x Height 461 (mm)
構造 Wall Mount, Drip Proof
Mass Approx.15kg
Transmitting Frequency 9410 ± 30MHz
Transmitting Power 25kW
Transmitting Tube Magnetron[M1568BS]
TX Pulse width / Repetition SP1：0.07μs/2250Hz
Frequency MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2/MP3
3NM ：MP1/MP2/MP3/LP1
6NM ：MP1/MP2/MP3/LP1/LP2
12NM ：MP1/MP2/MP3/LP1/LP2
24NM ：MP3/LP1/LP2
48NM ：LP2
96NM ：LP3
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier
Intermediate Frequency
Band Width
Gain
Amplifying Characteristics
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO
11 －16
60MHz
25/8/3MHz
more than 90dB
Logarithmic Amplifier
JMA-9100 Instruction Manual
11.17
11.SPECIFICATION
11.17 DISPLAY UNIT (NCD-4990)
DISPLAY UNIT (NCD-4990)
DISPLAY UNIT NCD-4990
Dimension Width 700 x Depth 850 x Height 1100 (mm)
Structure Self-Standing, Drip Proof
Mass Approx.130kg
Screen 23.1inch Color LCD (Effective Diameter, more than 320mm)
Viewing Distance 1m from the center of Display
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Marker 0.025, 0.05, 0.1, 0.25, 0.5, 1, 2, 4, 8, 16NM
Range Accuracyr Less than 1% of the Range Scale in use, or 30m whichever is larger
Variable Range Marker 2 (VRM1/VRM2)
VRM Scale 0.000 to 100.0nm, Numerical Indication in 4 digits
Bearing Scale 360° in 1° step
Off Center Within 66% of Radius, except 96nm range
Trackball Cursor Built-in (Target Range, Relative/True bearing Presentation)
Electronic Bearing Lines 2 (EBL1/EBL2) (on Center/Floating)
EBLBearing Indication 000.0° to 359.9°Numerical Indication in 4 digits
Tuning Indication Bar graph
Marking Function Electronic Mark (Maximum 20 points)
Heading Line Indication Electronic
True Motion Unit Built in (0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24 and 48nm)
Anti Sea Clutter (SEA) Manual/AUTO
Anti Rain Clutter (SEA) Manual/AUTO
Display mode North-up / Head-up / Course-up
Trails Indication Off/0.25/0.5/1/3/6/10/15min and Continues
Video Process (PROC) Built in (Scan correlation / Remain)
Interference Rejection (IR) Built in ( Off / Low / Middle / High)
Auto-acquisition Zone (AZ) Sector (2)
User Mapi Built in, Mark and Line (20,000 points)
Self diagnostic function Built in
Own Ship's Track Indicationi
Built in
Parallel Index Line (PI) Built in
AIS Indication Built in
Display 300
Activate 100
Association function:Built in
Interfacing Slave Display (TRG, VD, BP, BZ)
GPS
IEC61162-1(NMEA0183)
LOG
GYRO
AIS
IEC61162-2
Inter Switch (OPTION)
Radar Buoy
External Alarm output
Receivable Signal
11 －17
11
JMA-9100 Instruction Manual
11.SPECIFICATION
11.17 DISPLAY UNIT (NCD-4990)
Receive capability NAV1/ALM/ARPA/JARPA at terminal board TB4501
Port:
COM port (D-Sub 9 PIN)
Navigation equipment
IEC61162-1/2
Longitude/Latitude GGA>RMC>RMA>GNS>GLL
Waypoint RMB>BWC(BWR)
COG/SOG RMC ＞ RMA ＞ VTG
SPEED VBW
Day/Time information ZDA
Alarm acknowledge ACK
Rate of Turn ROT
Rudder RSA
Bearing signal
GYRO-SYNC 360x, 180x, 90x, 36x(GYRO I/F)
GYRO-STEP 360x, 180x, 90x, 36x(GYRO I/F)
IEC61162-2
38400bps
THS>HDT
over 40Hz
(HDG port at terminal board TB4501)
IEC61162-1ii HDT>HDG>HDM>VHW
(HDG port at terminal board TB4501)
Speed signal
LOG-SYNC 360x, 180x, 90x, 30x(GYRO I/F)
LOG-PULSE 800, 400, 200, 100(GYRO I/F)
External event mark Contact input (EVENT port at terminal board TB4601)
Radar buoy
Negative input (RBVD port at terminal board TB4401)
Depth
IEC61162-1/JRC DPT>DBS>DBT>DBK,
JRC format
Water temperature
IEC61162-1/JRC MTW, JRC format
Tendency
IEC61162-1/JRC CUR, JRC format
Wind
IEC61162-1 MWV>MWD
AIS
IEC61162-2 VDM,VDO (AIS port at terminal
board TB 4601 )
Acknowledge
Contact input (SYSACK, ARPAACK, PWRACK port
at terminal board TB4601)
Slave video
Radar video: TIY, VD, BP(2048p), BZ
(Terminal board TB4401)
Send capability
Port
NAV1, NAV2, ALM, ARPA, JARPA port
at terminal board TB4303. COM port (D-Sub 9 PIN)
Sendable Signal
Navigation information
Radar system data RSD
IEC61162-1/2
Own ship data OSD
Tracking target data TTM,TLL,TTD,TLB,JRC-ARPA
AIS target data TTM,TLL,TTD,TLB
Alarm ALR
Auto pilot APB
Bearing of destination BOD
Latitude/Longitude data
GGA,GLL,RMC
Waypoint RMB,BWC
COG/SOG VTG
Cross track error XTE
Heading data HDT,THS
External alarm
Default setting normally closed contact
11 －18
JMA-9100 Instruction Manual
11.SPECIFICATION
11.17 DISPLAY UNIT (NCD-4990)
Maximum current 200mA (SYSALM, ALPAALM, PWRALM
port at terminal board TB4601)
i.
Acknowledge
Contact output (ACKOUT port at terminal board TB4401)
Watchman reset
Contact output (WMRST port at terminal board TB4401)
Remote maintenance
JRC format (MNT port at terminal board TB4601)
AIS alarm acknowledge
ACK (AIS port at terminal board TB4601)
External monitor
Multi scan monitor
Analog RGB, HD15pin Connector 2 port
Only with Navigation Equipment is connected.
The Speed measuring accuracy of speed sensor shall confirm to IMO Resolution MSC.96(72).
The measuring accuracy of GPS shall confirm to IMO Resolution MSC.112(73).
ii. Can't be use for target tracking.
11
11 －19
JMA-9100 Instruction Manual
11.18
11.SPECIFICATION
11.18 Target Tracking Function
Target Tracking Function
Target Tracking
Function
Available range scale
Acquisition
All range
Acquisition mode Manual/AUTO（AUTO mode uses Auto-acquisition Zone）
Manual Cancellation Any one Target or All targets at once
Tracking
Number of Target 100 Targets (AUTO Tracking)
Maximum tracking range 32nm (Available all range scale)
Presentation
Display mode TM (True Motion) / RM (Relative Motion)
Azimuth mode North-up / Head-up / Course-up
Vector mode True/Relative Display
Vector Length Variable, 1 to 60 min. (1min. step)
Past Position True/Relative Display
Number of Dots…10 points
Display Interval Time…0.5 / 1 / 2/ 4 min
Time to Display Vector Within 1min
Time to Stabilize Vector Within 3min
Alarm
Auto-acquisition Zone 2 (sector)
Setting Range AZ1 (0.5 ～ 32NM),AZ2 (0.5 ～ 32NM)
Alarm Indication Symbol on Display, Visible / Audible Alarm
Safe Limits
Setting Condition CPA LIMIT
TCPA LIMIT
（CPA ／ TCPA）
Setting Condition Safe Target
0.1 to 9.9NM
1 to 99 minute
CPA ＞ CPA LIMIT
0 ＞ TCPA
TCPA ＞ TCPA LIMIT
Danger Target
CPA ≦ CPA LIMIT
0 ≦ TCPA ≦ TCPA LIMIT
Status Symbol
Alarm
Audible
Alarm Indication
Safe Target 〇 (wht)
Danger Target ○ (red)
OFF
OFF
CPA/TCPA
ON
Lost Target Symbol on Display
Visible / Audible Alarm
Data Indication
Target Data Simultaneous and Continuous Display for 4 Targets
True Bearing, Range, True Course, True Speed,CPA,TCPA,BCR,BCT
Own Ship's Data Course and Speed
Trial Maneuver Manual Setting
Trial Course 0°to 359.9°
Trial Speed 0 to 100 kn
Accuracy of Display Complied with IMO Requirement
System Failure Alarm
Visible / Audible Alarm
Speed Input Manual/AUTO (LOG)
11 －20
JMA-9100 Instruction Manual
11.19
11.SPECIFICATION
11.19 AIS FUNCTION
AIS FUNCTION
AIS 機能
Available range scale
Activation
All range
Activation mode Manual/AUTO（AUTO mode uses Auto-activation Zone）
Manual Cancellation Any one Target
Presentation Number of Activated Target 100 Targets
Number of Target 300 Targets (sleeping target and activated target)
Past Position True/Relative Display
Number of Dots…10 points
Display Interval Time…0.5 / 1 / 2/ 4 min
Display Interval distance…0.1 / 0.2 / 0.5/ 1 NM
Message Broadcast Message, Addressed Message
Display mode TM (True Motion) / RM (Relative Motion)
Azimuth mode North-up / Head-up / Course-up
Vector mode True/Relative Display
Vector Length Variable, 1 to 60 min. (1min. step)
Alarm
Auto-activation Zone 2 (Sector)
Setting Range AZ1(0.5 to 32nm), AZ2(0.5 to 32nm)
Alarm Indication Symbol on Display, Visible / Audible Alarm
Safe Limits
Setting Condition
CPA LIMIT 0.1 to 9.9NM
TCPA LIMIT 1 to 99min
（CPA ／ TCPA）
Alarm Condition Safe Target
CPA ＞ CPA LIMIT
0 ＞ TCPA
TCPA ＞ TCPA LIMIT
Danger Target
CPA ≦ CPA LIMIT
0 ≦ TCPA ≦ TCPA LIMIT
Status Symbol
Alarm
Audible
Alarm Indication
Safe Target △ (wht)
Danger Target △ (red)
OFF
OFF
CPA/TCPA
ON
Lost Target Symbol on Display
Visible / Audible Alarm
Data Indication
Target Data Simultaneous and Continuous Display for 2 Targets
simple display Ship's Name, Call Sign, MMSI, Course, Speed,
CPA and TCPA
detail display Ship's Name, Call Sign, MMSI, Course, Speed, CPA,
TCPA, Bearing, Range, Ship's Heading Bearing,
Rate of Turn, Latitude, Longitude, Destination
and Navigation Status
Own Ship's Data The ship's name, call sign, MMSI, course, speed,
ship's heading bearing, rate of turn, latitude,
longitude, destination and navigation status of own ship
Trial Maneuver Manual Setting
Trial Course 0° to 360°
Trial Speed 0 to 100 kn
11 －21
11
JMA-9100 Instruction Manual
11.SPECIFICATION
11.20 PERFORMANCE MONITOR (NJU-84)
Accuracy of Display Complied with IMO Requirement
System Failure Alarm
Visible / Audible Alarm
Speed Input Auto (LOG)
11.20
PERFORMANCE MONITOR (NJU-84)
PERFORMANCE MONITORNJU-84
Dimension Width 130 x Depth 180 x Height 70 (mm)
Mass Approx.0.7kg
Operating Frequency 3050 ± 30MHz
11.21
PERFORMANCE MONITOR (NJU-85)
PERFORMANCE MONITORNJU-85
Dimension Width 130 x Depth 149 x Height 70 (mm)
Mass Approx.0.7kg
Operating Frequency 9410 ± 30MHz
11.22
AC-DC CONVERTER (NBA-5135)
AC-DC CONVERTERNBA-5135
Dimension Width 315 x Depth 385 x Height 99 (mm)
Mass Approx.5kg
Power supply Input AC100 to 240V, 50/60Hz, 1φ
Output Voltage DC24V +/-5%
Output Current 12A max
11 －22
Appendix A
NQE-3141 Interswitch Unit
NQE-3141 Interswitch Unit
A.1
OVERVIEW ............................................................................................ A-1
A.1.1
Overview ......................................................................................... A-1
A.1.2
Interswitch Setup ........................................................................... A-1
A.2
INTERSWITCH OPERATION ................................................................ A-3
A.2.1
Operation Flow ............................................................................... A-3
A.2.2
Inter Switch Menu ........................................................................... A-4
A.2.3
Change of Connection Pattern (with 2 Display Units) ................ A-6
A.2.4
Change of Connection Pattern (with 3 or More Display Units) .. A-7
A.2.5
Operating Connection Pattern Files (File Operations) ............... A-8
A.2.6
Names of Display Units and Scanner Units ................................. A-9
A.3
REFERENCE ....................................................................................... A-10
A.3.1
Preheat Time after Change of Connection Pattern ................... A-10
A.3.2
Notes on Changing Connection Pattern .................................... A-10
A.3.3
Notes on Connecting Slave Display Unit ................................... A-10
A.3.4
Setting at Installation ................................................................... A-11
JMA-9100 Instruction Manual
A.1
A.1.1
A.NQE-3141 Interswitch Unit
A.1 OVERVIEW
OVERVIEW
Overview
Interswitch NQE-3141 is equipment that enables free changeover between radar
display units installed on the bridge and antenna units having different
characteristics.
If display unit is turned off or malfunctioned, the scanner unit can be controlled by
other display unit.
If interswitch unit had malfunctioned, the radar system is switched to standalone
mode.
Up to 8 units can be changed over.
When the connected scanner is changed, following setting values are
automatically loaded.
Tune Adjustment Section 7.1.3 "Tuning (Tune Adjustment)"
Bearing Adjustment Section 7.1.4 "Bearing Adjustment"
Range Adjustment Section 7.1.5 "Range Adjustment"
Antenna Height Section 7.1.8 "Antenna Height Setting (Antenna
Height)"
Antenna installation location Section 7.1.9 "Setting of CCRP (CCRP Setting)"
Sector Blank Section 7.2.2 "Sector Blank Setting (Sector Blank)"
TNI Blank Section 7.2.3 "TNI Blank Setting (TNI Blank)"
Performance monitor Section 7.3.4 "Adjustment of Performance Monitor"
adjustment
PRF Fine Tuning Section 3.8.3 "Set Scanner Unit (TXRX Setting)"
A.1.2
Interswitch Setup
Connection modes can be changed simply by changing the interswitch connection
(upper left of the display).
A master display unit is always necessary for establishing a slave
connection.
Before a slave display unit can be placed in transmission state, the
master display unit must be placed in transmission state.
A－ 1
JMA-9100 Instruction Manual
A.NQE-3141 Interswitch Unit
A.1 OVERVIEW
upper left of the display
Connected
Scanner
Unit
Connection
Mode
Connection Switch
The upper stand indicates the number of the connected scanner unit.
The lower stand indicates the connection mode.
i.
Master
:Mode in which the scanner unit can be controlled by the
display unit
Slave
:Mode in which the scanner unit cannot be controlledi
When Slave is selected, transmission / standby and pulse length cannot be changed.
The available range is also limited.
A－ 2
JMA-9100 Instruction Manual
A.2
A.NQE-3141 Interswitch Unit
A.2 INTERSWITCH OPERATION
INTERSWITCH OPERATION
Follow the flowchart below to change the current interswitch connection pattern.
A.2.1
Operation Flow
Place the transmission standby state .
Open the Inter Switch Menu .
Change the connection pattern .
Close the Inter Switch Menu .
A－ 3
JMA-9100 Instruction Manual
A.2.2
A.NQE-3141 Interswitch Unit
A.2 INTERSWITCH OPERATION
Inter Switch Menu
The Inter Switch Menu can be opened only when the transmission standby state.
Procedures
1)
Press the [TX/STBY] key to stop transmitting.
The transmission standby state will be placed.
2)
Move the cursor onto the Interswitch connection change (upper
left of the display), and left-click.
The Inter Switch Menu will appear.
Exit
1)
Left-click the
0.Exit
button.
The Inter Switch Menu will close.
Inter Switch Menu (with 2 Display Units)
Current
connection
status
a. Connection
pattern
Display unit
in operation
b. Set
A－ 4
c.Exit
JMA-9100 Instruction Manual
A.NQE-3141 Interswitch Unit
A.2 INTERSWITCH OPERATION
a. Connection pattern
If this button is clicked, the connection pattern is selected.
The display unit in operation is enclosed in a square □ .
The background of the current connection pattern display is highlighted.
b. Set
If this button is clicked, the change of connection is determined.
c. Exit
If this button is clicked, the Inter Switch Menu is closed .
If only 2 display units are installed but the interswitch is set for 3
or more display units, the Inter Switch Menu for 3 or more
display units will appear.
Inter Switch Menu (with 3 or More Display Units)
a. Connected
scanner unit
b. Display unit
connected as
master
c. Display unit
connected as
slave
f. Set
d. Name
e. File
Operations
a.
g. Exit
Connected scanner unit
In mode for naming a display unit or antenna unit, clicking on a unit opens the name input
window.
A－ 5
JMA-9100 Instruction Manual
A.NQE-3141 Interswitch Unit
A.2 INTERSWITCH OPERATION
b. Display unit connected as master
c. Display unit connected as slave
If this button is clicked, select / cancel the display unit.
If this button is clicked in the naming a display unit or scanner unit mode , the name input
window is opened .
d. Name
If this button is clicked, set to the display or scanner unit rename mode.
e. File Operations
If this button is clicked, the File Operations menu is opened.。
f. Set
If this button is clicked, the change of connection is determined.
g. Exit
If this button is clicked, the Inter Switch Menu is closed .
A.2.3
Change of Connection Pattern (with 2 Display Units)
If two display units are installed, a connection pattern needs to be selected.
Procedures
1)
Open the Inter Switch menu (with 2 Display Units).
2)
Move the cursor onto the Connection pattern (see Section A.2.2 "Inter
Switch Menu" and Section a. "Connection pattern") to be changed , and left-click.
The connection pattern will be selected, and
3)
Left-click the
3. Set
3. Set
button.
The connection pattern will be changed.
A－ 6
(Section b. "Set") will blink.
JMA-9100 Instruction Manual
A.2.4
A.NQE-3141 Interswitch Unit
A.2 INTERSWITCH OPERATION
Change of Connection Pattern (with 3 or More Display
Units)
If three or more display units are installed, the layout of connection patterns needs
to be set.
Procedures
1)
Open the Inter Switch Menu (with 3 or More Display Units).
2)
Move the cursor onto the display unit
(Section b. "Display unit connected as
master" or Section c. "Display unit connected as slave")
to be changed , and left-
click.
The selected display unit will be highlighted.
To deselect the display unit, left-click key again.
3)
Move the cursor to the change-destination display unit, and leftclick.
he selected display unit in step 2 will be switched to the change-destination display unit, and
3. Set
(Section f. "Set") will blink.
If the change destination is empty, control will move and 3. Set
4)
Left-click the
3. Set
will blink.
button.
The connection pattern will be changed.
A master display unit is always necessary for establishing a
slave connection.
A－ 7
JMA-9100 Instruction Manual
A.2.5
A.NQE-3141 Interswitch Unit
A.2 INTERSWITCH OPERATION
Operating Connection Pattern Files (File Operations)
Frequently used connection patterns can be read easily by saving interswitch
connection patterns.
[1] Loading connection patterns (Load)
Procedures
1)
Open the Inter Switch Menu (with 3 or More Display Units).
2)
Left-click the
button.
2. File Operation
The File Operations menu will appear.
3)
Left-click the
3. Load
button.
Currently saved connection patterns in memory will be listed.
4)
Left-click the button corresponding to the file to be loaded.
Confirmation Window will appear.
5)
Left-click the
1. Yes
to load.
The connection pattern will be changed.
[2] Saving connection patterns (Save)
Procedures
1)
Open the Inter Switch Menu (with 3 or More Display Units).
2)
Left-click the
2. File Operation
button.
The File Operations window will appear.
3)
Left-click the
2. Save
button.
The Save menu will appear.
Currently saved connection patterns in memory will be listed.
4)
Left-click the button corresponding to the file to be saved.
The Input File Name window will appear.
5)
Enter the file name to be saved.
Up to 8 characters can be entered.For the input method on the character input screen, see
Section 3.3.4.7 "Entering a character".
The connection pattern will be saved when the name is input.
A－ 8
JMA-9100 Instruction Manual
A.NQE-3141 Interswitch Unit
A.2 INTERSWITCH OPERATION
[3] Erasing a connection pattern (Erase)
Procedures
1)
Open the Inter Switch Menu (with 3 or More Display Units).
2)
Left-click the
2. File Operation
button.
The File Operations window will appear.
3)
Left-click the
button.
3. Erase
The Erase menu will appear.
The list of connection patterns stored in the memory will be displayed.
4)
Left-click the button corresponding to the file to be erased.
Confirmation Window will appear.
5)
Left-click the
1. Yes
to load.
The selected connection pattern is erased and the file name is deleted from the list.
A.2.6
Names of Display Units and Scanner Units
The display units and antenna units can be named.
Procedures
1)
Open the Inter Switch Menu (with 3 or More Display Units).
2)
Left-click the
1. Name
button.
"Name" will be highlighted, indicating that the rename mode is activated.
3)
Move the cursor to the display unit
(Section b. "Display unit connected as
or scanner unit (Section a.
to be renamed , and left-click.
master" or Section c. "Display unit connected as slave")
"Connected scanner unit")
he Input IND Name or the Input TXRX Name window will appear.
4)
Input a new unit name.
Up to 8 characters can be input as a unit name. For the input method on the character input
menu, see Section 3.3.4.7 "Entering a character".
The selected display unit or antenna unit will be renamed when the new name is input.
A－ 9
JMA-9100 Instruction Manual
A.3
A.3.1
A.NQE-3141 Interswitch Unit
A.3 REFERENCE
REFERENCE
Preheat Time after Change of Connection Pattern
After the current interswitch connection pattern has been changed, operation
needs to wait until the system is ready. This is because the preheat time varies
depending on the previous connection of the scanner unit and display unit.
The wait time is necessary for protecting the electronic tubes that emit radio
waves.
A.3.2
a) When not changed to a new connection pattern
Preheating not
required
b) When changed to a new connection pattern and an
scanner unit had been used before the change
Preheating not
required
c) When changed to a new connection pattern and an
scanner unit had not been used before the change
Preheating
required
Notes on Changing Connection Pattern
An attempt to change to another connection pattern immediately after the
completion of connection pattern change may fail.
This is because internal processing still needs some preparation time upon
completion of connection pattern change. Let several seconds pass between
connection pattern change operations.
A.3.3
Notes on Connecting Slave Display Unit
Before a slave display unit can be placed in transmission state, the master display
unit must be placed in transmission state. If the master display unit is moved from
the transmission state to the transmission standby state, the slave display unit is
forcibly placed in transmission standby state. When they are in transmission
standby state, TXRX Standby is shown in the alarm indication (lower right of the
display), and the alarm sounds.
A slave display unit cannot control tune. Tune is controlled by the master display
unit. Slave is shown in the transmitter pulse length (upper left of the display).
Range change for a slave display unit is limited by the range and pulse length /
repetition frequency of the master display unit. As a rule, a greater range than the
range of the master display unit cannot be set for a slave display unit. However, if
the transmitter pulse length of a slave display unit is identical to the master
display unit's and the repetition frequency is within the master display unit's, a
greater range than the master display unit's can be selected for the slave display
unit. When the master display unit narrows the range or changes the transmitter
A －10
JMA-9100 Instruction Manual
A.NQE-3141 Interswitch Unit
A.3 REFERENCE
pulse length, the range of the slave display unit may be forcibly changed. In this
case, Master Range CHG is shown in the alarm indication (lower right of the
display), and the alarm sounds.
A.3.4
Setting at Installation
Setting of the interswitch circuit (CCL-304*)
The settings of the DIP switches SW11 to SW13 are shown below.
SW 11
SW 13 SW 12
Interswitch circuit PCB
CCL-304*
1)
SW11 setting (extension mode and master/slave settings)
ON
OFF
Extension mode setting
Description
ON
Extension mode
OFF
Normal mode
Set the switch to OFF if the
number of connected display
units is four or less.
Master/slave setting
Description
ON
Slave
OFF
Master
Set the switch to ON if the
slave ISW PCB is selected in
extension mode.
Unused
1, 2
Description
ON
Unused
OFF
Unused
Set the switch to OFF in
normal state.
A－ 11
JMA-9100 Instruction Manual
2)
A.NQE-3141 Interswitch Unit
A.3 REFERENCE
SW12 setting (radar connection settings)
ON
OFF
Radar connection settings
ON
No.8 display unit connected
OFF
No.8 display unit not connected
ON
No.7 display unit connected
OFF
No.7 display unit not connected
ON
No.6 display unit connected
OFF
No.6 display unit not connected
ON
No.5 display unit connected
OFF
No.5 display unit not connected
ON
No.4 display unit connected
OFF
No.4 display unit not connected
ON
No.3 display unit connected
OFF
No.3 display unit not connected
ON
No.2 display unit connected
OFF
No.2 display unit not connected
ON
No.1 display unit connected
OFF
No.1 display unit not connected
3)
SW13 (unused)
ON
OFF
1,2,3,4
Unused (All OFF)
Before the DIP switches of the interswitch circuit can be set, the
interswitch breaker must be turned off in order to ensure safety
operation.
A －12
Appendix B
DRAWINGS
DRAWINGS
B.1
Interconnection Diagram of Display Unit ........................................... B-1
B.1.1
NCD-4990 ........................................................................................ B-2
B.1.2
NCD-4990 w/NBA-5135 ................................................................... B-3
B.1.3
NCD-4990T ...................................................................................... B-4
B.1.4
NCD-4990T w/NBA-5135 ................................................................ B-5
B.1.5
NWZ-170-R ...................................................................................... B-6
B.1.6
NWZ-170-RT .................................................................................... B-7
B.1.7
NCE-5163-R ..................................................................................... B-8
B.1.8
NCE-5163-RT ................................................................................... B-9
B.1.9
NBA-5135 ...................................................................................... B-10
B.2
Power System Daigram of Display Unit ........................................... B-11
B.3
Signal Flow Diagram of Display Unit ................................................ B-12
B.4
Primary Power System Diagram ....................................................... B-13
B.5
Block Diagram of Scanner Unit ........................................................ B-14
B.5.1
NKE-2103 ...................................................................................... B-15
B.5.2
NKE-2254 ...................................................................................... B-16
B.5.3
NKE-1125/NKE-1130 ..................................................................... B-17
B.5.4
NKE-1129, NTG-3225 / NKE-1139, NTG-3230 ............................. B-18
B.6
Interconnection Diagram of Scanner Unit ....................................... B-19
B.6.1
NKE-2103 ...................................................................................... B-20
B.6.2
NKE-2254 ...................................................................................... B-21
B.6.3
NKE-1125 (AC110V) ...................................................................... B-22
B.6.4
NKE-1125 (AC220V) ...................................................................... B-23
B.6.5
NKE-1129 (AC110V) ...................................................................... B-24
B.6.6
NKE-1129 (AC220V) ...................................................................... B-25
B.6.7
NTG-3225 ...................................................................................... B-26
B.6.8
NKE-1130 (AC110V) ...................................................................... B-27
B.6.9
NKE-1130 (AC220V) ...................................................................... B-28
B.6.10 NKE-1139 (AC110V) ...................................................................... B-29
B.6.11 NKE-1139 (AC220V) ...................................................................... B-30
B.6.12 NTG-3230 ...................................................................................... B-31
B.7
Terminal Board Connection Diagram ............................................... B-32
B.7.1
JMA-9110-6XA/JMA-9110-6XAH .................................................. B-33
B.7.2
JMA-9110-6XA/JMA-9110-6XAH (desktop) ................................. B-34
B.7.3
JMA-9122-6XAH ............................................................................ B-35
B.7.4
JMA-9122-6XAH (desktop) ........................................................... B-36
B.7.5
JMA-9122-6XA/9XA ...................................................................... B-37
B.7.6
JMA-9123-7XA/9XA ...................................................................... B-38
B.7.7
JMA-9132-SA ................................................................................ B-39
B.7.8
JMA-9133-SA ................................................................................ B-40
B.7.9
NCD-4990T .................................................................................... B-41
B.8
GYRO I/F ............................................................................................. B-42
B.9
Inter Switch Unit ................................................................................. B-44
B.9.1
Terminal Board Connection Diagram ......................................... B-44
B.9.2
Interconnection Diagram ............................................................. B-46
JMA-9100 Instruction Manual
B.1
B.DRAWINGS
B.1 Interconnection Diagram of Display Unit
Interconnection Diagram of Display Unit
B－ 1
NCD-4990
B.1.1
RADAR PROCESS UNIT
NDC-1399-9
SCA NN ER MOTOR
POW ER
R ED
WHT
BL U
R ED
BL U
WHT
AC O UT2
B ATTERY
IN
AC O UT2
2P
2P
20P
18P
8P
8P
J711
8P
H-7ZCR D1328
64P
J4401
64P
J4101
64P
J4403
64P
J4404
RADAR PROCESS
CIRCUIT
CDC-1324
PC440
64P
J 4402
64P
J 4102
64P
J4104
MOTHERBOARD
CQC-1192
PC410
64P
J4601
64P
J4501
AIS PROCESS
CIRCUIT
CDC-1325
PC460
ARPA PROCESS
CIRCUIT
CDC-1186D
PC450
GYRO INTERFACE
CIRCUIT
CMJ-462E
PC420
64P
J1
64P
J4103
2P
TB905
15P
TB911
11P
TB912
15P
TB913
11P
TB914
*OPTION
PC900
50P
J4105
50P
J4106
50P
J4107
*OPTION
(USER SUPPLY)
B102
B101
*PS/2 EX TENSION CA BLE
(U SER SU PPLY )
*PS/2 MOUSE/TRK BAL L
(U SER SUPPL Y)
CH1
CH2
W 401 H -7ZCRD 1339
W 402 H -7ZCRD 1339
W 403 H -7ZCRD 1339
6P
J6408
SP1
6P
J 6411
6P
J6409
14P
J6404
OPERATION
CIRCUIT B
CCK-974
PC620
7P
J6201
2P
7P
J6406 J6405
14P
J6101
15P
J6402
15P
J6102
OPERATION
CIRCUIT A
CCK-973
PC610
14P
J6403
30P
J4311
TO O PU
30P
J4312
TO SUB O PU
TO TRU
14P
TB4101
TO ISW
26P
TB4201
T O EXT-RA DAR
30P
TB4401
TO SEN SOR
22P
TB4501
TO PC
9P
J4310
T O L OG
12P
TB4801
TO G YRO
6P
TB4701
TO A LAR M SYSTEM
22P
TB4601
TERMINAL BOARD
CQD-2097
PC430
2m H -7ZC RD 1337 (N CE-5163-R )
JR C SU PPLY
OPERATION CIRCUIT D
CCK-976
30P
J 6401
PC640
6P
J 6410
A1
OPERATION UNIT
NCE-5163-R
9P
J4309
3P
J4313
26P
J4306
3P
J4314
26P
J4307
2P
J4308
50P
J4301
50P
J4302
50P
J4303
18P
J4304
8P
J4305
Fig B-1: Interconnection Diagram of NCD-4990
LCD
OPERATION
CIRCUIT
CCK -972 PC710
9P 2m H -7ZCRD 1329A (N W Z-170-R )
15P
J 4409
V GA
15P
J 4405
V GA
28P
J 4406
D VI-D
8P
J 4407
R J-45
50P
J 4408
C F-c ard
20P
J4108
AC 100-115V 50/60H z
AC 220-240V 50/60H z
NCD-4990（自立型） 機内接続図
JMA-9122-6/9XA,JMA-9123-7/9XA,JMA-9132-SA,JMA-9133-SA
Interconnection diagram of DISPLAY UNIT type NCD-4990(self standing)
B－ 2
LCD PANEL
H-7WSRD0002A
D VI 2m H -7ZCRD 1345 (N W Z-170-R)
POWER SUPPLY
CBD-1661
4351A07335 FILTER
IN W
INTERSWITCH UNIT
NQE-3141-2A
MONITOR UNIT
NWZ-170-R
ー
AC 2m 5ZCG H 00285 (N WZ-170-R)
W OU T
AC IN
B.1 Interconnection Diagram of Display Unit
B.DRAWINGS
JMA-9100 Instruction Manual
NCD-4990 w/NBA-5135
B.1.2
FG
FG
R ED
WHT
R ED
W406 H-7ZCRD 1342A
AC OUT2
B ATTERY
IN
AC OUT2
LCD PANEL
H-7WSRD0002A
2P
2P
20P
IN W
8P
18P
4351A07335 FIL TER
8P
J711
8P
H-7ZCR D1328
64P
J4401
64P
J4101
CDC-1324
PC440
64P
J4403
64P
J4404
CQC-1192
PC410
64P
J4104
MOTHERBOARD
64P
J 4102
64P
J 4402
RADAR PROCESS
CIRCUIT
L CD
OPERATION
CIRCUIT
CCK -972 PC710
9P 2m H -7ZCRD 1329A (N W Z-170-R )
15P
J 4409
V GA
15P
J 4405
V GA
28P
J 4406
D VI-D
8P
J 4407
R J-45
50P
J 4408
C F-c ard
20P
J4108
AC 100-115V 50/60H z
AC 220-240V 50/60H z
64P
J4601
64P
J4501
AIS PROCESS
CIRCUIT
CDC-1325
PC460
ARPA PROCESS
CIRCUIT
CDC-1186D
PC450
GYRO INTERFACE
CIRCUIT
CMJ-462E
PC420
64P
J1
64P
J4103
*OPTION
15P
TB913
11P
TB914
11P
TB912
15P
TB911
2P
PC900 TB905
50P
J4105
50P
J4106
50P
J4107
*OPTION
(USER SUPPLY)
B102
B101
*PS/2 EX TENSION CA BLE
(U SER SU PPLY )
*PS/2 MOUSE/TRK BAL L
(U SER SUPPL Y)
CH1
CH2
W 401 H -7ZCRD 1339
W 402 H -7ZCRD 1339
W 403 H -7ZCRD 1339
6P
J6408
A1
6P
J 6411
6P
J6409
14P
J6404
OPERATION
CIRCUIT B
CCK-974
PC620
7P
J6201
2P
7P
J6406 J6405
14P
J6101
15P
J6402
15P
J6102
OPERATION
CIRCUIT A
CCK-973
PC610
14P
J6403
30P
J4311
TO OPU
30P
J4312
TO SUB OPU
TO TRU
14P
TB4101
TO ISW
26P
TB4201
T O EXT-RA DAR
30P
TB4401
TO SEN SOR
22P
TB4501
TO PC
9P
J4310
T O L OG
12P
TB4801
TO G YRO
6P
TB4701
TO A LAR M SYSTEM
22P
TB4601
TERMINAL BOARD
CQD-2097
PC430
2m H -7ZC RD 1337 (N CE-5163-R )
JR C SU PPLY
OPERATION CIRCUIT D
CCK-976
30P
J 6401
PC640
6P
J 6410
SP1
OPERATION UNIT
NCE-5163-R
9P
J4309
3P
J4313
26P
J4306
3P
J4314
26P
J4307
2P
J4308
50P
J4301
50P
J4302
50P
J4303
18P
J4304
8P
J4305
NCD-4990（自立型） 機内接続図
JMA-9110-6XA,JMA-9110-6XAH,JMA-9122-6XAH
Interconnection diagram of DISPLAY UNIT type NCD-4990(self standing)
B－ 3
Fig B-2: Interconnection Diagram of NCD-4990 w/NBA-5135
MONITOR UNIT
NWZ-170-R
ー
D VI 2m H -7ZCRD 1345 (N WZ-170-R)
POWER SUPPLY
CBD-1661
RADAR PROCESS UNIT
NDC-1399-9
TB522
AC IN
ー
TB521
DC24V OUT
WHT
BL U
AC 2m 5ZCG H 00285 (N WZ-170-R)
W OU T
INTERSWITCH UNIT
NQE-3141-2A
RED
SCAN NER MO TOR
POWER D C24V
R ED
BL U
WHT
AC IN
WHT
AC/DC
CONVERTER UNIT
NBA-5135
B.1 Interconnection Diagram of Display Unit
B.DRAWINGS
JMA-9100 Instruction Manual
NCD-4990T
B.1.3
TB 402
BL U
BL U
R ED
WHT
R ED
BL U
WHT
AC OUT2
B ATTERY
IN
AC OUT2
2P
2P
20P
18P
8P
IN W
8P
J711
8P
H-7ZCR D1328
64P
J4401
64P
J4101
64P
J4403
64P
J4404
RADAR PROCESS
CIRCUIT
CDC-1324
PC440
64P
J 4402
64P
J 4102
64P
J4104
MOTHERBOARD
CQC-1192
PC410
64P
J4601
64P
J4501
AIS PROCESS
CIRCUIT
CDC-1325
PC460
ARPA PROCESS
CIRCUIT
CDC-1186D
PC450
GYRO INTERFACE
CIRCUIT
CMJ-462E
PC420
64P
J1
64P
J4103
*OPTION
15P
TB913
11P
TB914
11P
TB912
15P
TB911
2P
PC900 TB905
50P
J4105
50P
J4106
50P
J4107
*OPTION
(USER SUPPLY)
B102
B101
*PS/2 EX TENSION CA BLE
(U SER SU PPLY )
*PS/2 MOUSE/TRK BAL L
(U SER SUPPL Y)
CH1
CH2
W 401 H -7ZCRD 1339
W 402 H -7ZCRD 1339
W 403 H -7ZCRD 1339
6P
J6408
A1
6P
J 6411
6P
J6409
14P
J6404
OPERATION
CIRCUIT B
CCK-974
PC620
7P
J6201
2P
7P
J6406 J6405
14P
J6101
15P
J6402
15P
J6102
OPERATION
CIRCUIT A
CCK-973
PC610
14P
J6403
30P
J4311
TO OPU
30P
J4312
TO SUB OPU
TO TRU
14P
TB4101
TO ISW
26P
TB4201
T O EXT-RA DAR
30P
TB4401
TO SEN SOR
22P
TB4501
TO PC
9P
J4310
T O L OG
12P
TB4801
TO G YRO
6P
TB4701
TO A LAR M SYSTEM
22P
TB4601
TERMINAL BOARD
CQD-2097
PC430
5m H -7ZC RD 1338 (N CE-5163-R T)
JR C SU PPLY
OPERATION CIRCUIT D
CCK-976
30P
J 6401
PC640
6P
J 6410
SP1
OPERATION UNIT
NCE-5163-RT
9P
J4309
3P
J4313
26P
J4306
3P
J4314
26P
J4307
2P
J4308
50P
J4301
50P
J4302
50P
J4303
18P
J4304
8P
J4305
Fig B-3: Interconnection Diagram of NCD-4990T
L CD
OPERATION
CIRCUIT
CCK -972 PC710
9P 5m H -7ZCRD 1330A (N W Z-170-R T)
15P
J 4409
V GA
15P
J 4405
V GA
28P
J 4406
D VI-D
8P
J 4407
R J-45
50P
J 4408
C F-c ard
20P
J4108
AC 100-115V 50/60H z
AC 220-240V 50/60H z
NCD-4990T（卓上型） 機内接続図
JMA-9122-6/9XA,JMA-9123-7/9XA,JMA-9132-SA,JMA-9133-SA
Interconnection diagram of DISPLAY UNIT type NCD-4990T(desktop)
B－ 4
LCD PANEL
H-7WSRD0002A
D VI 5m H -7ZCRD 1346 (N WZ-170-RT)
POWER SUPPLY
CBD-1661
4351A07335 FIL TER
INTERSWITCH UNIT
NQE-3141-2A
MONITOR UNIT
NWZ-170-RT
ー
AC 5m 5ZCG H 00364 (N WZ-170-RT)
W OU T
AC IN
RADAR PROCESS UNIT
NDC-1399-9T
SCAN NER MOTO R
POW ER
RED
W 405 H -7ZC RD1341A
WH T
B.1 Interconnection Diagram of Display Unit
B.DRAWINGS
JMA-9100 Instruction Manual
NCD-4990T w/NBA-5135
B.1.4
FG
TB 402
WHT
B LK
G RN
BL U
R ED
WHT
AC OUT2
B ATTERY
IN
AC OUT2
LCD PANEL
H-7WSRD0002A
2P
2P
20P
IN W
8P
18P
4351A07335 FIL TER
8P
J711
8P
H-7ZCR D1328
64P
J4401
64P
J4101
CDC-1324
PC440
64P
J4403
64P
J4404
CQC-1192
PC410
64P
J4104
MOTHERBOARD
64P
J 4102
64P
J 4402
RADAR PROCESS
CIRCUIT
L CD
OPERATION
CIRCUIT
CCK -972 PC710
9P 5m H -7ZCRD 1330A (N W Z-170-R T)
15P
J 4409
V GA
15P
J 4405
V GA
28P
J 4406
D VI-D
8P
J 4407
R J-45
50P
J 4408
C F-c ard
20P
J4108
AC 100-115V 50/60H z
AC 220-240V 50/60H z
64P
J4601
64P
J4501
AIS PROCESS
CIRCUIT
CDC-1325
PC460
ARPA PROCESS
CIRCUIT
CDC-1186D
PC450
GYRO INTERFACE
CIRCUIT
CMJ-462E
PC420
64P
J1
64P
J4103
*OPTION
15P
TB913
11P
TB914
11P
TB912
15P
TB911
2P
PC900 TB905
50P
J4105
50P
J4106
50P
J4107
*OPTION
(USER SUPPLY)
B102
B101
*PS/2 EX TENSION CA BLE
(U SER SU PPLY )
*PS/2 MOUSE/TRK BAL L
(U SER SUPPL Y)
CH1
CH2
W 401 H -7ZCRD 1339
W 402 H -7ZCRD 1339
W 403 H -7ZCRD 1339
6P
J6408
A1
6P
J 6411
6P
J6409
14P
J6404
OPERATION
CIRCUIT B
CCK-974
PC620
7P
J6201
2P
7P
J6406 J6405
14P
J6101
15P
J6402
15P
J6102
OPERATION
CIRCUIT A
CCK-973
PC610
14P
J6403
30P
J4311
TO OPU
30P
J4312
TO SUB OPU
TO TRU
14P
TB4101
TO ISW
26P
TB4201
T O EXT-RA DAR
30P
TB4401
TO SEN SOR
22P
TB4501
TO PC
9P
J4310
T O L OG
12P
TB4801
TO G YRO
6P
TB4701
TO A LAR M SYSTEM
22P
TB4601
TERMINAL BOARD
CQD-2097
PC430
5m H -7ZC RD 1338 (N CE-5163-R T)
JR C SU PPLY
OPERATION CIRCUIT D
CCK-976
30P
J 6401
PC640
6P
J 6410
SP1
OPERATION UNIT
NCE-5163-RT
9P
J4309
3P
J4313
26P
J4306
3P
J4314
26P
J4307
2P
J4308
50P
J4301
50P
J4302
50P
J4303
18P
J4304
8P
J4305
NCD-4990T（卓上型） 機内接続図
JMA-9110-6XA,JMA-9110-6XAH,JMA-9122-6XAH
Interconnection diagram of DISPLAY UNIT type NCD-4990T(desktop)
B－ 5
Fig B-4: Interconnection Diagram of NCD-4990T w/NBA-5135
MONITOR UNIT
NWZ-170-RT
ー
D VI 5m H -7ZCRD 1346 (N WZ-170-RT)
POWER SUPPLY
CBD-1661
RADAR PROCESS UNIT
NDC-1399-9T
GR N
FG
GR N
AC 5m 5ZCG H 00364 (N WZ-170-RT)
W OU T
INTERSWITCH UNIT
NQE-3141-2A
TB522
AC IN
ー
TB521
DC24V OUT
R ED
BL U
WHT
AC IN
BL K
TB401
W408 H -7ZC RD 1344A
RED
W 405 H -7ZC RD1341A
BL U
G RN
SCAN NER MO TOR
POWER D C24V
W407 H-7ZCRD 1343A
WH T
WH T
AC/DC
CONVERTER UNIT
NBA-5135
B.1 Interconnection Diagram of Display Unit
B.DRAWINGS
JMA-9100 Instruction Manual
JMA-9100 Instruction Manual
B.DRAWINGS
B.1 Interconnection Diagram of Display Unit
NWZ-170-R
H-7WSRD0002A
LCD
CCK-972
PC710
AC 2m VM0301-VM0303B2Mｸﾛ
CBD-1661
OUTLET
AC 1 00V
24 0V
9P 2m H-7ZCRD1329A
FAN
ALM
CQD-2097
J4309
DVI
DVI 2m H-7ZCRD1345
RGB
CDC-1324
J4406
B.1.5
J7101
BRILL
FL1
8P
H-7ZCRD1328
CML-764-R (NWZ-170-R)
Monitor Unit Interconnection
Fig B-5: Interconnection Diagram of NWZ-170-R
B－ 6
JMA-9100 Instruction Manual
B.DRAWINGS
B.1 Interconnection Diagram of Display Unit
NWZ-170-RT
H-7WSRD0002A
LCD
CCK-972
PC710
AC 5m VM0301-VM0303B5Mｸﾛ
CBD-1661
OUTLET
AC 1 00V
24 0V
9P 5m H-7ZCRD1330A
FAN
ALM
CQD-2097
J4309
DVI
DVI 5m H-7ZCRD1346
RGB
CDC-1324
J4406
B.1.6
J7101
BRILL
FL1
8P
H-7ZCRD1328
CML-764-RT (NWZ-170-RT)
Monitor Unit Interconnection
Fig B-6: Interconnection Diagram of NWZ-170-RT
B－ 7
JMA-9100 Instruction Manual
B.DRAWINGS
B.1 Interconnection Diagram of Display Unit
NCE-5163-R
OPERATION UNIT
NCE-5163-R
OPERATION
CIRCUIT B
CCK-974
PC620
OPERATION
CIRCUIT A
CCK-973
PC610
A1
7P
J6201
14P
J6101
15P
J6102
6P
J6411
6P
J6408
2P
7P
J6406 J6405
14P
J6404
W64 H-7ZCRD1334
W65 H-7ZCRD1335
W63 H-7ZCRD1333A
SP1
W62 H-7ZCRD1332
B.1.7
14P
J6403
15P
J6402
OPERATION CIRCUIT D
CCK -976
PC 640
6P
J6410
6P
J6409
2P
J6407
30P
J6401
FL1
W67 2m H-7ZCRD1337
CMD-996-R (NCE-5163-R)
Operation Unit Interconnection
Fig B-7: Interconnection Diagram of NCE-5163-R
B－ 8
JMA-9100 Instruction Manual
B.DRAWINGS
B.1 Interconnection Diagram of Display Unit
NCE-5163-RT
OPERATION UNIT
NCE-5163-RT
OPERATION
CIRCUIT B
CCK-974
PC620
OPERATION
CIRCUIT A
CCK-973
PC610
A1
7P
J6201
14P
J6101
15P
J6102
6P
J6411
6P
J6408
2P
7P
J6406 J6405
14P
J6404
W64 H-7ZCRD1334
W65 H-7ZCRD1335
W63 H-7ZCRD1333A
SP1
W62 H-7ZCRD1332
B.1.8
14P
J6403
15P
J6402
OPERATION CIRCUIT D
CCK -976
PC 640
6P
J6410
6P
J6409
2P
J6407
30P
J6401
FL1
W68 5m H-7ZCRD1338
CMD-996-RT (NCE-5163-RT)
Operation Unit Interconnection
Fig B-8: Interconnection Diagram of NCE-5163-RT
B－ 9
JMA-9100 Instruction Manual
B.DRAWINGS
B.1 Interconnection Diagram of Display Unit
NBA-5135
W6 H-7ZCRD1499
FS1
TB521
RED
BLK
W1 H-7ZCRD1495
WHT
TB 522
BLK
WHT
WHT
W5 H-7ZCRD1499
W2 H-7ZCRD1496
Twisted
RED
W4 H-7ZCRD1498
WHT
BLK
+ + + -
FL1
LF-210
A1
AES300-24B
W3 H-7ZCRD1497
RED
BLK WHT
FG
BLK
u FG v
RED
WHT
B.1.9
Twisted
BLK
CBD-1684A (NBA-5135)
AC/DC Converter Interconnection
Fig B-9: Interconnection Diagram of NBA-5135
B －10
Power System Daigram of Display Unit
B.2
FG
U,V
DC+24V
U,V
R ED
W HT
BL U
W HT
AC OUT2
B ATTERY
IN
AC OUT2
LCD PANEL
H-7WSRD0002A
2P
2P
20P
3.3V,5V,
12V,-12V
18P
3.3V,5V,12V,-12V
+48V,DC+24V
8P
4351A07335 FIL TER
8P
J711
8P
H-7ZCR D1328
9P 2m H -7ZCRD 1329A (N WZ-170-R )
15P
J 4409
V GA
15P
J 4405
V GA
28P
J 4406
D VI-D
8P
J 4407
R J-45
64P
J4401
64P
J4101
5V
64P
J4403
64P
J4404
3.3V
64P
J4104
MOTHERBOARD
64P
J 4102
64P
J 4402
CDC-1324
PC440
RADAR PROCESS
CIRCUIT
L CD
OPERATION
CIRCUIT
CCK -972 PC710
CQC-1192
3.3V,5V,12V,-12V
PC410
50P
J 4408
C F-c ard
20P
J4108
AC 100-115V 50/60H z
AC 220-240V 50/60H z
64P
J4601
64P
J4501
AIS PROCESS
CIRCUIT
CDC-1325
PC460
ARPA PROCESS
CIRCUIT
CDC-1186D
PC450
64P
J1
GYRO INTERFACE
CIRCUIT
CMJ-462E
PC420
P+5V
64P
J4103
*OPTION
11P
TB914
15P
TB913
11P
TB912
15P
TB911
2P
TB905
*OPTION
(USER SUPPLY)
W403 H -7ZCRD 1339
W402 H -7ZCRD 1339
W401 H -7ZCRD 1339
B102
B101
*PS/2 EX TENSION CA BLE
(U SER SU PPLY )
*PS/2 MOUSE/TRK BAL L
(U SER SUPPL Y)
CH1
CH2
P+12V
PC900
50P
J4105
50P
J4106
50P
J4107
7P
J6201
2P
7P
J6406 J6405
14P
J6404
OPERATION
CIRCUIT B
CCK-974
PC620
OPERATION UNIT
NCE-5163-R
A1
6P
J6408
SP1
6P
J 6411
6P
J6409
14P
J6101
15P
J6402
15P
J6102
OPERATION
CIRCUIT A
CCK-973
PC610
14P
J6403
2m H -7ZC RD 1337 (N CE-5163-R )
5m H -7ZC RD 1338 (N CE-5163-R T)
JR C SU PPLY
P+12V
DC+24V
TO OPU
30P
J4311
+48V
30P
TO SUB OPU
J4312
(to SCANNER
UNIT)
TO TRU
14P
TB4101
TO ISW
26P
TB4201
T O EXT-RA DAR
30P
TB4401
TO SEN SOR
22P
TB4501
TO PC
9P
J4310
T O L OG
12P
TB4701
TO G YRO
6P
TB4701
TO A LAR M SYSTEM
22P
TB4601
TERMINAL BOARD
CQD-2097
PC430
P+5V
OPERATION CIRCUIT D
CCK-976
30P
J 6401
PC640
6P
J 6410
+5V
9P
J4309
3P
J4313
26P
J4306
3P
J4314
26P
J4307
2P
J4308
50P
J4301
50P
J4302
50P
J4303
3.3V,5V,12V,-12V
+48V,DC+24V
18P
J4304
8P
J4305
NCD-4990 電源系統図
Fig B-10: Power System Diagram of NCD-4990/T
MONITOR UNIT
NWZ-170-R
ー
IN W
Power supply system diagram of DISPLAY UNIT type NCD-4990(self standing)
B－ 11
AC100-115V
AC220-240V
50/60H z,1φ
RADAR PROCESS UNIT
NDC-1399-9
FG
W 406 H-7ZCRD 1342A
AC100-115V
AC220-240V
50/60Hz,1φR ED
R ED
AC 2m 5ZCG H00285 (N WZ-170-R )
W OU T
D VI 2m H-7ZCRD 1345 (N W Z-170-R)
POWER SUPPLY
CBD-1661
JMA-9110-6XA
JMA-9110-6XAH
JMA-9122-6XAH
only
U,V
TB522
AC IN
AC100-115V
AC220-240V
50/60Hz,1φ
ー
TB521
DC24V OUT
+24V
SCAN NER MOTOR
POWER D C24V
BL U
W HT
INTERSWITCH UNIT
NQE-3141-2
RED
INPUT VOLTAGE
SELECT SWITCH
AC IN
WHT
AC/DC
CONVERTER UNIT
NBA-5135
B.2 Power System Daigram of Display Unit
B.DRAWINGS
JMA-9100 Instruction Manual
Signal Flow Diagram of Display Unit
B.3
FG
FG
TB521
DC24V OUT
ー
R ED
W HT
BL U
W 406 H-7ZCRD 1342A
AC OUT2
AC OUT2
B ATTERY
IN
8P
8P
J711
Dimmer
H-7ZCR D1328
9P 2m H -7ZCRD 1329A (N WZ-170-R )
15P
J 4409
V GA
Analog RGB
J 4405
V GA
Analog
RGB
15P
J 4406
D VI-D
De28P
gital Video Inte rface
Ethernet
8P
J 4407
R J-45
50P
J 4408
C F-c ard
64P
J4101
64P
J4403
64P
J4404
CQC-1192
PC410
64P
J4104
MOTHERBOARD
64P
J 4102
J 4402
64P
Serial,GPIO
CDC-1324
PC440
RADAR PROCESS
CIRCUIT
L CD
OPERATION
CIRCUIT
CCK -972 PC710
Radar video,
64P
Trigger,Rotation
J4401
20P
J4108
AC 100-115V 50/60H z
AC 220-240V 50/60H z
64P
J4601
64P
J4501
AIS PROCESS
CIRCUIT
CDC-1325
PC460
ARPA PROCESS
CIRCUIT
CDC-1186D
PC450
64P
J1
GYRO INTERFACE
CIRCUIT
CMJ-462E
PC420
GYRO/LOG
64P
J4103
2P
TB905
15P
TB911
11P
TB912
15P
TB913
11P
TB914
*OPTION
PC900
50P
J4105
50P
J4106
50P
J4107
*OPTION
(USER SUPPLY)
*PS/2 MOUSE/TRK BAL L
(U SER SUPPL Y)
PS/2
I/F
3P
J4313
3P
J4314
26P
J4306
26P
J4307
2P
J4308
50P
J4301
50P
J4302
50P
J4303
18P
J4304
8P
J4305
A1
6P
J6408
PS/2
I/F
6P
J 6411
6P
J6409
14P
J6404
15P
J6402
KEY matrix
Encoder
15P
J6102
OPERATION
CIRCUIT A
CCK-973
PC610
14P
J6101
14P
J6403
Power SW
7P
J6201
OPERATION
CIRCUIT B
CCK-974
PC620
Audio
2P
7P
J6406 J6405
TO OPU
30P
J4311
TO SUB OPU
30P
J4312
TO TRU
14P
TB4101
TO ISW
26P
TB4201
Se rial
Ra dar video
Trigger,Rota
Dry Contact
Serial
Radar video,
Trigger,Rotatio
Rada r video,
Trigger,Rotatio
Serial
T O EXT-RA DAR
30P
TB4401
TO SEN SOR
22P
TB4501
GYRO
(STEP/SYN
LOG
(PULSE/SYN
Serial
NCD-4990 信号系統図
TO PC
9P
J4310
T O L OG
12P
TB4701
TO G YRO
6P
TB4701
TO A LAR M SYSTEM
22P
TB4601
TERMINAL BOARD
CQD-2097
PC430
2m H -7ZC RD 1337 (N CE-5163-R )
5m H -7ZC RD 1338 (N CE-5163-R T)
JR C SU PPLY
OPERATION CIRCUIT D
CCK-976
30P
J 6401
PC640
6P
J 6410
SP1
OPERATION UNIT
NCE-5163-R
9P
J4309
LCD Fan Alarm
*PS/2 EX TENSION CA BLE
(U SER SU PPLY )
B101
B102
Rada r video,
Trigger,Rotation
CH1
Rada r video,
CH2
Trigger,Rotation
W401
-7ZCRD 1339
Rada
r Hvideo,
Trigger,Rotation
W402 H -7ZCRD 1339
Serial,GPIO
W403 H -7ZCRD 1339
GYRO/LOG
Powe r supply Control
Powe r supply Fan alarm
B －12
LCD PANEL
H-7WSRD0002A
2P
2P
20P
18P
8P
Power supply Control
Power supply Fa n alarm
4351A07335 FIL TER
IN W
Signal flow diagram of DISPLAY UNIT type NCD-4990
Fig B-11: Signal Flow Diagram of NCD-4990/T
MONITOR UNIT
NWZ-170-R
ー
D VI 2m H-7ZCRD 1345 (N W Z-170-R)
POWER SUPPLY
CBD-1661
RADAR PROCESS UNIT
NDC-1399-9
TB522
AC IN
RED
R ED
W HT
R ED
AC 2m 5ZCG H00285 (N WZ-170-R )
W OU T
INTERSWITCH UNIT
NQE-3141-2
WHT
AC/DC
CONVERTER UNIT
NBA-5135
SCAN NER MOTOR
POWER D C24V
BL U
W HT
AC IN
B.3 Signal Flow Diagram of Display Unit
B.DRAWINGS
JMA-9100 Instruction Manual
Primary Power System Diagram
B.4
AC100-115V
AC220-240V
50/60Hz,1φ
OVER VOLTAGE
PROTECTION
LINE FILTER
P+12V
SCANNER
X BAND_2.5A, S BAND_3.0A
INTERSWITCH=1A
OPERATION UNIT=0.5A(typ)
GYRO I/F CIRCUIT=0.1A(typ)
RADAR PROCESS CIRCUIT = 1.2A(typ)
ARPA PROCESS CIRCUIT = 0.15A(typ)
AIS PROCESS CIRCUIT = 0.15(typ)
TERMINAL BOARD = 1.0A(typ)
+48V±3V
+5.0V
+3.3V
RADAR PROCESS CIRCUIT = 2.2A(typ)
ARPA PROCESS CIRCUIT = 0.1A(typ)
AIS PROCESS CIRCUIT = 0.1(typ)
TERMINAL BOARD = 0.2A(typ)
RADAR PROCESS CIRCUIT = 0.1A(typ)
TERMINAL BOARD = 0.4A(typ)
RADAR PROCESS CIRCUIT = 0.1A(typ)
TERMINAL BOARD = 0.1A(typ)
Fig B-12: Primary Power System Diagram
CIRCUIT
BREAKER
VOLTAGE SELCT
SWITCH
MONITOR UNIT
POWER
SCAN NER MOTOR
POWER
POWER CONTROL
CIRCUIT
+12V
-12V
OPERATION UNIT = 0.1A
B －13
AC100-115V
AC220-240V
50/60Hz,1φ
SCANNER
MOTOR
POWER
AC100/230V
1φ
BATTRY
DC24V
FAN ALM POWER CONTROL
B.4 Primary Power System Diagram
B.DRAWINGS
JMA-9100 Instruction Manual
JMA-9100 Instruction Manual
B.5
B.DRAWINGS
B.5 Block Diagram of Scanner Unit
Block Diagram of Scanner Unit
B －14
JMA-9100 Instruction Manual
B.5.1
B.DRAWINGS
B.5 Block Diagram of Scanner Unit
NKE-2103
NKE-2103 Scanner Unit
SLOT ANTENNA
ROTARY
JOINT
MOTOR
B101
ENCODER
ΦA,ΦB,ΦZ
FILTER
DIODE
LIMITER
MAG
V101
RECEIVER
PULSE
TRANS
Tune Control
DUMMY
LOAD
Receiver
Bandwidth
Control
SWITCHING
CIRCUIT
MIC
IF AMP
PC 201
Tx Trigger/Pulse Width
VIDEO
AMP
MH
GENERATOR
POWER
SUPPLY
CIRCUIT
INTERFACE
CIRCUIT
AVR
PC 1001
Status
Rotation Control
Serial Com, BP, BZ, VD, TRIG
DC +24V
DC +24V
Speed control
MOTOR CONTROL
POWER
SAFETY SWITCH
DC +24V
S101
PC1501
Fig B-13: Block Diagram of NKE-2103
B －15
>
JMA-9100 Instruction Manual
B.5.2
B.DRAWINGS
B.5 Block Diagram of Scanner Unit
NKE-2254
NKE-2254 Scanner Unit
SLOT ANTENNA
ROTARY
JOINT
MOTOR
B101
ΦA,ΦB,ΦZ
ENCODER
FILTER
DIODE
LIMITER
MAG
V101
RECEIVER
PULSE
TRANS
Tune Control
DUMMY
LOAD
Receiver
Bandwidth
Control
SWITCHING
CIRCUIT
RF AMP
IF AMP
PC 201
Tx Trigger/Pulse Width
VIDEO
AMP
MH
GENERATOR
POWER
SUPPLY
CIRCUIT
INTERFACE CIRCUIT
PC1101
AVR
PC 1001
Status
Rotation Control
Serial Com, BP, BZ, VD, TRIG
DC +24V
DC +24V
Speed control
MOTOR CONTROL
POWER
SAFETY SWITCH
S101
PC1501
Fig B-14: Block Diagram of NKE-2254
B －16
DC +24V
JMA-9100 Instruction Manual
B.5.3
B.DRAWINGS
B.5 Block Diagram of Scanner Unit
NKE-1125/NKE-1130
NKE-1130/NKE-1125 Scanner Unit
SLOT ANTENNA
ROTARY
JOINT
MOTOR
B101
ERROR
MOTOR
DRIVER
ΦA,ΦB,ΦZ
ENCODER
FILTER
PC1501
DIODE
LIMITER
MAG
V101
RECEIVER
PULSE
TRANS
Tune Control
DUMMY
LOAD
Receiver
Bandwidth
Control
SWITCHING
CIRCUIT
RF AMP
IF AMP
PC 201
Tx Trigger/Pulse Width
VIDEO
AMP
MH
GENERATOR
POWER
SUPPLY
CIRCUIT
INTERFACE CIRCUIT
PC1101
AVR
PC 1001
Relay Control
Status
Serial Com, BP, BZ, VD, TRIG
DC+48V
MOTOR RELAY
SAFETY SWITCH
PC1201
S101
AC100/110/220 /230V
50/60Hz,1φ
Fig B-15: Block Diagram of NKE-1125/NKE-1130
B －17
JMA-9100 Instruction Manual
B.5.4
B.DRAWINGS
B.5 Block Diagram of Scanner Unit
NKE-1129, NTG-3225 / NKE-1139, NTG-3230
NKE-1139/NKE-1129 Scanner Unit
SLOT ANTENNA
MOTOR
DRIVER
ROTARY
JOINT
MOTOR
B101
PC1501
ENCODER
ΦA,ΦB,ΦZ
DIODE LIMITER
/ TRHPL
PIN ATT
AC100/110/220/230V
50/60Hz,1φ
ERROR
SAFETY SWITCH
Status
S101
NTG-3230 /NTG-3225
Transceiver Unit
FILTER
MAG
V101
(X-band)
RECEIVER
PULSE
TRANS
Tune Control
DUMMY
LOAD
Receiver
Bandwidth
Control
SWITCHING
CIRCUIT
RF AMP
IF AMP
PC 201
Tx Trigger/Pulse Width
VIDEO
AMP
MH
GENERATOR
POWER
SUPPLY
CIRCUIT
INTERFACE CIRCUIT
PC1101
AVR
Serial Com, BP, BZ, VD, TRIG
PC1001
Relay Control
DC+48V
AC100/110 /220/230V
50/ 60Hz,1φ
MOTOR RELAY
PC1201
Fig B-16: Block Diagram of NKE-1129, NTG-3225 / NKE-1139, NTG-3230
B －18
JMA-9100 Instruction Manual
B.6
B.DRAWINGS
B.6 Interconnection Diagram of Scanner Unit
Interconnection Diagram of Scanner Unit
B －19
NKE-2103
B.6.1
S.G.
S.G.
100pF× 3
MAG
GRN
A103
NJC 4002
DUMMY
NJC9952
A104
ANTENNA NAX-16B-4/6
FILTER
DISPLAY
UNIT
6.TXI
7.TXE
8.NC
1.PTI
2.PTE
3.LVR
4.PMS
5.E
J8
1.ΦZ
2.E
3.ΦA
4.ΦB
5.+12V
6.F.G.
J208
P8
YEL
BLK
BLU
WHT
RED
SHIELD
(W108)
Z CRD1305※
SE
B102
(RECEIVER UNIT INTERCONNECTION CMA-823)
TRANSMITTER/RECEIVER UNIT ＮZT－２１０３
TRANSMITTER/RECEIVER UNIT
INTERCONNECTION
CMK-599
RECEIVER UNIT ＮＲＧ－６１０
CAE-529-1
IF AMP CIRCUIT (PC301)
3.E
P81
WHT
BLK
WHT
BRN
PM
NJU-85 (OPTION）
S.G.
J82 P82
1.LVR
BLU
2.PMS
RED
BLK
J81
1.PTI
2.PTE
3.TXI
4.TXE
DISPLAY
UNIT
1.VD
2.VDE
3.COM+
4.COM-
3.GND
H-7ZCRD####*:
“#” means specification document No.
“*” means revision of the specfication document.
1.HMCNT
2.+15V
3.GND
1.TUNE
2.+5V
4.NC
5.IF
J18
A301
E101
NJS6930 NJT1969
MIC
T201-15
T201-16
1.MH
J206
3.MN
TB1
1-2short : Nomal Speed
2-3short : High Speed
MODULATOR CIRCUIT
(PC201)
CME-３６３
6.C2
7.BZ
SAFETY SWITCH
WS101
ZCRD1306※
DISPLAY
UNIT
J2
NKE-2103 / 2103HS
空中線機内接続図
Fig B-17: Interconnection Diagram of NKE-2103
A102
F CX68
(W204)
ZCRD1312※
(W103)
ZCRD1300※
(W104)
ZCRD1301※
J205
1.+15V
2.+12V
3.+8V
4.AGND
5.-15V
6.X1
7.X2
8.+5V
9.HTER
10.HVER
J204
1.2A
2.1A
(W107)
ZCRD1304※
J1504
1.MS1
2.NC
3.MS2
J1505
1.HMCNT
2.+15V
3.AGND
J5
1.2A
2.1A
7ZCRD 1280※
A101
F CX68
WV101
J1003
3.MN
1.MH
J1002
(W105)
ZCRD1302※
J1503
1.2A
2.1A
1.MPS
2.PW3
3.PW2
4.PW1
5.MCT
6.MBK
7.+15V
8.AGND
9.-7V
10.BP
MOTOR CONTROL POWER CIRCUIT J4
1.2A
(PC1501)
2.1A
CBD-1779
1.MCNT+
2.MCNT3.NC
J125
J1502
1.M+
2.NC
3.M4.NC
6.C2
7.BZ
MAGNETRON
V101
MAF1565N
YEL
CFR-234
MAG FILTER
CIRCUIT
POWER SUPPLY
CIRCUIT
(PC1001)
CBD-1783
1.+15V
2.+12V
3.+8V
4.AGN D
5.-15V
6.X1
7.X2
8.+5V
9.HTER
10.HV ER
J1001
1.2A
2.1A
(W110) ZCRD1307※
BREAK CIRCUIT CFA-252
MOTOR
B101
H-7BDRD0048
MORTOR CBP-202
CAX-10
3.LVR
4.PMS
5.GND
6.TXI
7.TXE
1.ETIY
2.AGND
3.EXBP
4.AGND
5.ＥＸＢＺ
D.L
SCANNER UNIT INTERCONNECTION
1.TIY
2.AGND
3.MAG.I
4.HTER
5.HVER
J1
B －20
1.PTI
2.PTE
3.LVR
4.PMS
5.GND
6.TXI
7.TXE
J3
1.2A
2.1A
1.TIY
2.AGND
3.MAG.I
4.HTER
5.HVER
J210
1.C2G
2.C2
(W111)
ZCRD1308※
ENCODER CHT -71A
1.PTI
2.PTE
6.AGND
J303
(W10６)
ZCRD1303※
J203
J302
(W102)
ZCRD1290※
J202
11.HSP
12.TI
13.+8V
14.MOD ID
15.NC
11.HSP
12.TI
13.+8V
14.MOD ID
15.NC
J301
(W101)
ZCRD1289※
J201
1.MPS
2.PW3
3.PW2
4.PW1
5.MCT
6.MBK
7.+15V
8.AGND
9.-7V
10.BP
J209
1.MPS
2.MCT
3.MBK
J1501
1.MPS
2.MCT
3.MBK
B.6 Interconnection Diagram of Scanner Unit
B.DRAWINGS
JMA-9100 Instruction Manual
NKE-2254
B.6.2
RECEIVER CIRCUIT
CMA-866A
BM15B-XASS-TE
J101
RECEIVER UNIT NRG-162A
P3001
(W001)
ZCRD1251※
P1110
J1110
IL-4P
J1191
IL-G -11P
Ａ301
NJS6930
P1111
②
②
Ａ104
NJC 9952
ANTENNA
FILTER
Ａ103
NJC4002
DUMMY
①
③
①
J2102
(W107)
ZCRD1259※
P2101
IL-10P
1.SHORT
2.MAG I
No.2
3.X1
MODULATOR No.1
4.X2
5.TI
CIRCUIT
6.TIE
CPA-264
7.+15V
J2103
8.G ND
350209-2
J2101
9.NC
1.X1
1586514-2
10.NC
2.X2
P1002
DISPLAY UNIT
(W106)
ZC RD1258※
MAG
T1
C201
0.01UF 1KV
H-7LPRD0122
C202
0.22UF 200V
IL-3P-S3EN2
IL-G-3P-S3T2-SA
J1501
Ｖ101
M1568BS
S.G.
S.G.
MOTOR CONTROL
POWER CIRCUIT
CBD-1779
1.HMC NT
2.+15V
3.E
J1505
S.G.
PULSE TANS
ｱｵ
ｼﾛ
ｸﾛ
P1505
(W201)
ZCRD1260※
CMB-404
MODULATOR UNIT
INTERCONNECTION
(W104)
ZCRD1256※
(W103)
ZCRD1255※
MODULATOR UNIT NMA-550
Ａ102
NJ C3901M
③
Ａ101
NJC 3901M
(W003)
ZCRD1252※
P2102
P1003
10
P1004
10
(W004)
ZCRD1253※
(W207)
Z CRD1448※
1 BLU
2 WHT
3 BLK
P1118
BLU
WHT
BLK
P1103
P1104
1.+15V
2.+12V
3.+8V
J1002
4.GND
1586514-2
5.-15V
6.X1
7.X2
POWER SUPPLY J1001
350428-1
8.+5V
CIRCUIT
1.M+
1.MC T
2.MCBD-1682A
2.MBK
3.HSP
4.HTER
5.TISTOP
6.C 2
J4
J5
J3
350209-1 350209-1 B02P-NV(LF)(SN ）
7.G ND
8.MPS
9.MIER
WHT
RED
ZCRD1449※
(W302)
S.G.
220pF× 5
CFR-229
MAG FILTER
CIRCUIT
J1503
IL-2P-S3E N2
J125
B3P-SHF-1AA
1.MCNT2.MCNT+
3.NC
P1502
B4P-VH
1.M+
2.NC
3.M4.NC
BREAK C IRCUIT
CFA-257
GRN
YEL
BRN
(W307)
ZC RD 1450※
(W305)
BLU.T
BLK.T
(W301)
MOTOR
B101
(W401)
ZCRD1508※
※NKE-2254HS
・MOTOR CBP-182
MOTOR CBP-168A / CBP-182
HEATER CONTROL
PART
CHG-216
（OPTION）
TB105
Fig B-18: Interconnection Diagram of NKE-2254
B102
P1109
J1109
IL-G-8P
1.SHORT
2.MAG I
3.X1
4.X2
5.TI
6.TIE
7.+15V
8.GND
9.NC
10.NC
11.NC
12.NC
1.HMC NT
2.+15V
3.GND
1.+15V
2.+12V
3.G ND
4.GND
5.-15V
6.10V
7.10VE
8.+5V
1.MC T
2.MBK
3.TISTOP
4.G ND
5.MPS
6.MIER
J1105
P2103
SE
J13
P13 IL-6P
YEL
1.φZ
BLK
2.φZE
BLU
3.φ A
WHT
4.φB
RED
5.+12V
SHIELD
6.GND
IL-G -6P
IL-G-3P
J1114
1 2 3
J1
1.TIY
2.TIYE
3.BP
4.BPE
5.BZ
6.BZE
T/R CONTROL CIRCUIT
CMC-1205R
IL-G-3P
J1113
IL-G-2P
P1105
(W206)
ZCRD1447※
WHT.T
B －21
IL-G -4P
MSTBA2.5/11-G
IL-G-9P
J1112
P1114
(W006)
ZCRD1254※
R1
10Ω ,10W
J2
1.VD
2.VDE
3.MTR+
4.MTR-
50/60ｋW
J1106
IL-G-5P
P1113
FAN
P1503
P125
P1502
P1303
R201 CD202 CD 201
150Ω MD-12N1 MD-12N1
8W
J4
SAFETY SWITCH
CSD-653
350209-1
NKE-2254 / 2254HS
空中線機内接続図
1.2A
2.1A
J5
(W105)
ZCRD1257※
350209-1
BLK.T
1.MH
2.NC
3.MN
2.1A
1.2A
R202
2.7KΩ
1/2W
1.MS1
2.NC
3.MS2
TB101
J8
1.BP+
2.BP3.BZ+
4.BZ5.TRIG+
6.TRIG7.MTR+
8.MTR9.MTRE
10.VD+
11.VD-
IL-8P
B201
FAN
H-7BFRD0002
B202
S101
S-32
TH101
1.2A
2.1A
(W308
ZCRD 1494※
B3P-VH
1 2 3
ﾐﾄﾞﾘ
(W208)
ZCRD1451※
J1303
2.1A
1.2A
1.MH
2.NC
3.MN
BLK.T
ｷ
J1504
P1504
ｱｶ太
J1003
J1004
C 203
0.22UF
200V
1.MPS
2.MCT
3.MBK
B8P-SHF
B9P-SHF
2.1A
1.2A
D.L
SCANNER UNIT INTERCONNECTION
CAX-15
P1501
P1301
P1302
IL -G -12P
J1118
J1103
1.+12V
2.GND
3.FAN _ERR 2
J1301
J1302
J1111
B3P-SHF
B8P-SHF
B6P-SHF
(W009)
H-7ZCRD####*:
“#” means specification document No.
“*” means revision of the specfication document.
H-7BF RD0002
(W010)
1.HTER1
2.HVGATE1
3.TISTOP1
4.GND
5.CNT
6.+5V
7.+15V
8.STABY_REQ
9.NC
J1104
1.RXD
2.TXD
3.+5V
4.GND
RED
BLU
YEL
1.+12V
2.GND
3.FAN_ERR1
RED
BLU
YEL
1.+12V
2.C 2
RED
WHT
1.MONI
2.GS
3.GSE
4.TGT
5.TGTE
6.TNL
7.-15V
8.TNI
9.+15V
10.GND
11.TRG2
1.PW1
2.PW2
3.PW3
4.+24V
5.GND
S.G.
ｼﾛ太
TR101
（100W）
UTH
UTH
(W018)
ZCRD1277※
PM
ZCRD1280※
P81 J81
1.PTI
2.PTE
3.TXI
4.TXE
NJU-85
WHT
CHT-71A
ENCODER
1.BS3
2.BS2
3.BS1
4.TNC
5.+5V
6.-15V
7.+15V
8.GND
9.TGT
10.TGTE
11.TNI
12.VD_DC
13.TNL
14.VDE
15.VD
P82 J 82
1.LVR
BLU
2.PMS
RED
3.E
BLK
(W017)
DISPLAY UNIT
1.BS3
2.BS2
3.BS1
4.TNC
5.MicPS
6.VDINE
7.VDIN
8.+5V
1.PTI
2.PTE
3.LVR
4.PMS
5.GND
6.TXI
7.TXE
8.NC
BLK
WHT
BRN
B.6 Interconnection Diagram of Scanner Unit
B.DRAWINGS
JMA-9100 Instruction Manual
NKE-1125 (AC110V)
B102
RECEIVER UNIT NRG-162A
J101
RECEIVER CIRCUIT CMA-866A
BM15B-XASS-TE
IL-G-8P
J1109
P1110
IL-4P
J1191
IL-G -11P
J1110
IL-G-3P
J1114
1.SHORT
2.MAGI
3.X1
4.X2
5.TI
6.TIE
7.+15V
8.GND
9.NC
10.NC
11.NC
12.NC
1.HMC NT
2.+15V
3.GND
1.+15V
2.+12V
3.G ND
4.GND
5.-15V
6.10V
7.10VE
8.+5V
1.MC T
2.MBK
3.TISTOP
4.G ND
5.MPS
6.MIER
IL-G-2P
J1105
A301
NJS6930
P1111
②
②
Ａ104
NJC9952
ANTENNA
FILTER
A103
NJC4002
DUMMY
①
③
①
J2102
(W107)
ZCRD1259※
P2101
IL-10P
1.SHORT
2.MAG I
3.X1
MODULATOR No.2
No.1
4.X2
CIRCUIT
5.TI
6.TIE
CPA-264
7.+15V
J2103
350209-2
8.GND
9.NC
J2101
1.X1
1586514-2
10.NC
2.X2
(W206)
ZC RD 1262※
(W308)
ZC RD 1537※
W 101
P3
to CCB-655 J1941
(W203)
ZCRD1261※
(W106)
ZC RD1258※
(W104)
ZCRD1256※
BLU
WHT
BLK
MAG
T1
C201
0.01UF 1KV
PULSE
TRANS
H-7LPRD 0122
C202
0.22UF 200V
S.G.
S.G.
Ｖ101
M1568BS
S.G.
(W308)
ZC RD1537※
to TB102
S.G.
CFR-229
MAG FILTER
CIRCUIT
220pF ×5
P1941 J1941
1.+12V
2.NC
3.+12VE
S3B-XH-A
B2PS-VH
R4
R3
R2
120Ω
×4
30W
R1
330Ω
30W ×1
R1
1-350209-0
(W309)
ZCRD1538※
P1911
J1911
BRAKE CIRCUIT B
CFA-260
BRAKE CIRCUIT A
CFA-259
(W310)
ZC RD1539※
P1921
J1921
1-350210-0
IL-2P
B3P-VH
1.R1
2.NC
3.R2
PC 1501
B201 H-7EPRD0035
B2P-VH
J1505
(W307)
ZCRD1536※
P1505
CCB-655
1.MU2
2.NC
3.MV2
4.N C
5.N C
6.G ND
P1503
H-7BDRD0050
CBP-203
MOTOR
J1905
P1905
BRAKE CONTROL CIRCUIT
1-480700-0
CBD-2001
AC100V
MOTOR DRIVER
J1903
P1903
(W303)
ZCRD1452※
1.VERR1
2.E
(W305)
Z CRD1454※ J1912 P1912
J1212 P1212
IL-2P
1.VERR1
2.E
J1201
B4P-VH
P1201
(W302)
ZC RD1265※
(W301)
ZCRD1264※
SAFETY SWITCH
CSD-654
1 0 P1
UTH
UTH
B3P-NV
2.+15V RELAY FILTER
J1202 P1202
3.G ND
CIRCUIT 1.MU2
CSC-656 2.GND
3.MV2
PC1201
1.HMCNT
IL-3P
(W201)
ZCRD1260※
CMB-404
MODULATOR UNIT
INTERCONNECTION
1.+15V
2.+12V
3.+8V
J1002
4.GND
1586514-2
5.-15V
6.X1
J1001
7.X2
POWER
SUPPLY
350428-1
8.+5V
1.M+
CIRCUIT
1.MC T
2.MCBD-1682A
2.MBK
3.HSP
4.HTER
5.TISTOP
6.C 2
J4
J5
J3
350209-1 350209-1 B02P-NV(LF)(SN ）
7.G ND
8.MPS
9.MIER
P1002
(W103)
ZCRD1255※
MODULATOR UNIT NMA-550
Ａ102
NJ C3901M
③
Ａ101
NJC3901M
(W003)
ZCRD1252※
P2102
1 BL U
2 WHT
3 BLK
(W207)
ZCRD1263※
P1003
10
WHT
RED
P1004
10
(W004)
ZCRD1253※
P1118
BLU
WHT
BLK
P1103
P1104
TH101
W401 7ZCRD1508※
B 101
MOTOR
P1502
WC1
(W304)
ZCRD1314※
R1
R2
1.2kΩ
30W ×2
BRAKE CIRCUIT
CFA-253
Fig B-19: Interconnection Diagram of NKE-1125 (AC110V)
P3001
(W001)
Z CRD1251※
P1109
IL-G -6P
IL-G-3P
J1113
T/R CONTROL CIRCUIT
CMC-1205R
IL-G-9P
J1112
P1114
HEATER
CONTROL PART
TR101 WHT.T
（100W）
TB105 U
R201 CD202 CD201
150Ω MD-12N1 MD-12N1
8W
(W105)
ZCRD1257※
SE
J13
J1
P13 IL-6P
YEL
1.φZ
BLK
2.φZE
BLU
3.φ A
WHT
4.φB
RED
5.+12V
SHIELD
6.GND
IL-G -4P
MSTBA2.5/11-G
50/60ｋW
P1113
P1105
1 2 3
D.L
(W006)
ZCRD1254※
TB102
P1303
CHG-216
（OPTION）
NKE-1125PM (AC100V) X25kW,2ﾕﾆｯﾄ
空中線機内接続図
B －22
1.TIY
2.TIYE
3.BP
4.BPE
5.BZ
6.BZE
J2
1.VD
2.VDE
3.MTR+
4.MTR-
TB101
1.BP+
2.BP3.BZ+
4.BZ5.TRIG+
6.TRIG7.MTR+
8.MTR9.MTRE
10.VD+
11.VD-
IL-G-5P
J1106
B201
FAN
FAN
H-7BF RD0002
H-7BFRD0002
B202
DISPLAY UNIT
J1504
P1504
1.BKS1
2.BKS2
1.VERR
2.E
1.VERR
2.E
1.M1
2.NC
3.M2
4.NC
5.M3
J 1502
BLK
2.N
1 2 3
P2103
1.MH
2.NC
3.MN
2.1A
1.2A
1.BKH1
2.NC
3.BKH1
B6P-VH
1.P
2.NC
3.N
RED
1.P
BLK.T
R202
2.7KΩ
1/2W
BLK.T
BLK.T
1.MH
2.NC
3.MN
W101
YEL
1.U1
2.NC
3.V1
4.NC
RED.T
BLK.T
RED.T
J1303
2.1A
1.2A
IL -G -12P
J1118
J1103
SCANNER UNIT INTERCONNECTION
CAX-11
WHT.T
1.S1
2.S2
3.S3
4.S4
5.S5
6.S6
J1503
C 203
0.22UF
200V
S101
S-32F
J1003
J1111
B3P-SHF
B8P-SHF
B6P-SHF
GRN
P1211
J1211
B8P-SHF
J1004
W1
IL-8P
S.G.
+12V
B9P-SHF
V1
W1
P1301
+48V
+48VG
P1302
+48V
+48VG
2.1A
1.2A
V1
J1301
J1302
1.HTER1
2.HVGATE1
3.TISTOP1
4.GND
5.CNT
6.+5V
7.+15V
8.STABY_REQ
9.NC
J1104
1.RXD
2.TXD
3.+5V
4.GND
1.+12V
2.GND
3.FAN _ERR 2
RED
BLU
YEL
1.+12V
2.GND
3.FAN_ERR1
RED
BLU
YEL
1.+12V
2.C 2
ｱｶ
ｼﾛ
1.MONI
2.GS
3.GSE
4.TGT
5.TGTE
6.TNL
7.-15V
8.TNI
9.+15V
10.GND
11.TRG2
1.PW1
2.PW2
3.PW3
4.+24V
5.GND
J8
ZCRD1280※
P82 J 82
BLU
1.LVR
RED
2.PMS
BLK
3.E
PM
U1
U1
(W018)
ZCRD1277※
NJU-85
P81 J81
1.PTI
2.PTE
3.TXI
4.TXE
CHT-71A
ENCODER
1.BS3
2.BS2
3.BS1
4.TNC
5.+5V
6.-15V
7.+15V
8.GND
9.TGT
10.TGTE
11.TNI
12.VD_DC
13.TNL
14.VDE
15.VD
BLK
WHT
BRN
(W017)
DISPLAY UNIT
1.BS3
2.BS2
3.BS1
4.TNC
5.MicPS
6.VDINE
7.VDIN
8.+5V
1.PTI
2.PTE
3.LVR
4.PMS
5.GND
6.TXI
7.TXE
8.NC
WHT
1 0J5 1
B.6.3
B.6 Interconnection Diagram of Scanner Unit
B.DRAWINGS
JMA-9100 Instruction Manual
NKE-1125 (AC220V)
B102
RECEIVER UNIT NRG-162A
J101
RECEIVER CIRCUIT CMA-866A
BM15B-XASS-TE
IL-G-8P
J1109
P1110
IL-4P
J1191
IL-G -11P
J1110
IL-G-3P
J1114
1.SHORT
2.MAGI
3.X1
4.X2
5.TI
6.TIE
7.+15V
8.GND
9.NC
10.NC
11.NC
12.NC
1.HMC NT
2.+15V
3.GND
1.+15V
2.+12V
3.G ND
4.GND
5.-15V
6.10V
7.10VE
8.+5V
1.MC T
2.MBK
3.TISTOP
4.G ND
5.MPS
6.MIER
IL-G-2P
J1105
A301
NJS6930
P1111
②
②
Ａ104
NJC9952
ANTENNA
FILTER
A103
NJC4002
DUMMY
①
③
①
J2102
(W107)
ZCRD1259※
P2101
IL-10P
1.SHORT
2.MAG I
3.X1
MODULATOR No.2
No.1
4.X2
CIRCUIT
5.TI
6.TIE
CPA-264
7.+15V
J2103
350209-2
8.GND
9.NC
J2101
1.X1
1586514-2
10.NC
2.X2
(W206)
ZC RD 1262※
(W308)
ZC RD 1537※
W 101
P3
to CCB-655 J1941
(W203)
ZCRD1261※
(W106)
ZC RD1258※
(W104)
ZCRD1256※
BLU
WHT
BLK
MAG
T1
C201
0.01UF 1KV
PULSE
TRANS
H-7LPRD 0122
C202
0.22UF 200V
S.G.
S.G.
Ｖ101
M1568BS
S.G.
(W308)
ZC RD1537※
to TB102
S.G.
CFR-229
MAG FILTER
CIRCUIT
220pF ×5
P1941 J1941
1.+12V
2.NC
3.+12VE
S3B-XH -A
B2PS-VH
R4
R3
R2
120Ω
×4
30W
R1
330Ω
30W ×1
R1
1-350209-0
(W309)
ZCRD1538※
P1911
J1911
BRAKE CIRCUIT B
CFA-260
BRAKE CIRCUIT A
CFA-259
(W310)
ZC RD1539※
P1921
J1921
1-350210-0
IL-2P
B3P-VH
1.R1
2.NC
3.R2
PC 1501
B201 H-7EPRD0034
B2P-VH
J1505
(W307)
ZCRD1536※
P1505
CCB-655
1.MU2
2.NC
3.MV2
4.N C
5.N C
6.G ND
P1503
H-7BDRD0050
CBP-203
MOTOR
J1905
P1905
BRAKE CONTROL CIRCUIT
1-480700-0
CBD-2000
AC220V
MOTOR DRIVER
J1903
P1903
(W303)
ZCRD1452※
1.VERR1
2.E
(W305)
Z CRD1454※ J1912 P1912
J1212 P1212
IL-2P
1.VERR1
2.E
J1201
B4P-VH
P1201
(W302)
ZC RD1265※
(W301)
ZCRD1264※
SAFETY SWITCH
CSD-654
1 0 P1
UTH
UTH
B3P-NV
2.+15V RELAY FILTER
J1202 P1202
3.G ND
CIRCUIT 1.MU2
CSC-656 2.GND
3.MV2
PC1201
1.HMCNT
IL-3P
(W201)
ZCRD1260※
CMB-404
MODULATOR UNIT
INTERCONNECTION
1.+15V
2.+12V
3.+8V
J1002
4.GND
1586514-2
5.-15V
6.X1
J1001
7.X2
POWER
SUPPLY
350428-1
8.+5V
1.M+
CIRCUIT
1.MC T
2.MCBD-1682A
2.MBK
3.HSP
4.HTER
5.TISTOP
6.C 2
J4
J5
J3
350209-1 350209-1 B02P-NV(LF)(SN ）
7.G ND
8.MPS
9.MIER
P1002
(W103)
ZCRD1255※
MODULATOR UNIT NMA-550
Ａ102
NJ C3901M
③
Ａ101
NJC3901M
(W003)
ZCRD1252※
P2102
1 BL U
2 WHT
3 BLK
(W207)
ZCRD1263※
P1003
10
WHT
RED
P1004
10
(W004)
ZCRD1253※
P1118
BLU
WHT
BLK
P1103
P1104
TH101
W401 7ZCRD1508※
B 101
MOTOR
P1502
WC1
(W304)
ZCRD1314※
R1
R2
1.2kΩ
30W ×2
BRAKE CIRCUIT
CFA-253
Fig B-20: Interconnection Diagram of NKE-1125 (AC220V)
P3001
(W001)
Z CRD1251※
P1109
IL-G -6P
IL-G-3P
J1113
T/R CONTROL CIRCUIT
CMC-1205R
IL-G-9P
J1112
P1114
HEATER
CONTROL PART
TR101 WHT.T
（100W）
TB105 U
R201 CD202 CD201
150Ω MD-12N1 MD-12N1
8W
(W105)
ZCRD1257※
SE
J13
J1
P13 IL-6P
YEL
1.φZ
BLK
2.φZE
BLU
3.φ A
WHT
4.φB
RED
5.+12V
SHIELD
6.GND
IL-G -4P
MSTBA2.5/11-G
50/60ｋW
P1113
P1105
1 2 3
D.L
(W006)
ZCRD1254※
TB102
P1303
CHG-216
（OPTION）
NKE-1125PM (AC220V) X25kW,2ﾕﾆｯﾄ
空中線機内接続図
B －23
1.TIY
2.TIYE
3.BP
4.BPE
5.BZ
6.BZE
J2
1.VD
2.VDE
3.MTR+
4.MTR-
TB101
1.BP+
2.BP3.BZ+
4.BZ5.TRIG+
6.TRIG7.MTR+
8.MTR9.MTRE
10.VD+
11.VD-
IL-G-5P
J1106
B201
FAN
FAN
H-7BF RD0002
H-7BFRD0002
B202
DISPLAY UNIT
J1504
P1504
1.BKS1
2.BKS2
1.VERR
2.E
1.VERR
2.E
1.M1
2.NC
3.M2
4.NC
5.M3
J 1502
BLK
2.N
1 2 3
P2103
1.MH
2.NC
3.MN
2.1A
1.2A
1.BKH1
2.NC
3.BKH2
B6P-VH
1.P
2.NC
3.N
RED
1.P
BLK.T
R202
2.7KΩ
1/2W
BLK.T
BLK.T
1.MH
2.NC
3.MN
W101
YEL
1.U1
2.NC
3.V1
4.NC
RED.T
BLK.T
RED.T
J1303
2.1A
1.2A
IL -G -12P
J1118
J1103
SCANNER UNIT INTERCONNECTION
CAX-11
WHT.T
1.S1
2.S2
3.S3
4.S4
5.S5
6.S6
J1503
C 203
0.22UF
200V
S101
S-32F
J1003
J1111
B3P-SHF
B8P-SHF
B6P-SHF
GRN
P1211
J1211
B8P-SHF
J1004
W1
IL-8P
S.G.
+12V
B9P-SHF
V1
W1
P1301
+48V
+48VG
P1302
+48V
+48VG
2.1A
1.2A
V1
J1301
J1302
1.HTER1
2.HVGATE1
3.TISTOP1
4.GND
5.CNT
6.+5V
7.+15V
8.STABY_REQ
9.NC
J1104
1.RXD
2.TXD
3.+5V
4.GND
1.+12V
2.GND
3.FAN _ERR 2
RED
BLU
YEL
1.+12V
2.GND
3.FAN_ERR1
RED
BLU
YEL
1.+12V
2.C 2
ｱｶ
ｼﾛ
1.MONI
2.GS
3.GSE
4.TGT
5.TGTE
6.TNL
7.-15V
8.TNI
9.+15V
10.GND
11.TRG2
1.PW1
2.PW2
3.PW3
4.+24V
5.GND
J8
ZCRD1280※
P82 J 82
BLU
1.LVR
RED
2.PMS
BLK
3.E
PM
U1
U1
(W018)
ZCRD1277※
NJU-85
P81 J81
1.PTI
2.PTE
3.TXI
4.TXE
CHT-71A
ENCODER
1.BS3
2.BS2
3.BS1
4.TNC
5.+5V
6.-15V
7.+15V
8.GND
9.TGT
10.TGTE
11.TNI
12.VD_DC
13.TNL
14.VDE
15.VD
BLK
WHT
BRN
(W017)
DISPLAY UNIT
1.BS3
2.BS2
3.BS1
4.TNC
5.MicPS
6.VDINE
7.VDIN
8.+5V
1.PTI
2.PTE
3.LVR
4.PMS
5.GND
6.TXI
7.TXE
8.NC
WHT
1 0J5 1
B.6.4
B.6 Interconnection Diagram of Scanner Unit
B.DRAWINGS
JMA-9100 Instruction Manual
NKE-1129 (AC110V)
TB103
U1
V1
W1
+12V
C2
ΦZE
ΦZ
ΦA
ΦB
（W301) ZCRD1285※
RED.T
S101
S-32
RED
S.G.
C102
2200p
50V
RED.T
S.G.
C101 +
1000μ
16V
BLK.T
SE
B102
RED
ENCORDER CHT-71A1
J81 P81
AC100V
（W302) ZCRD1286※
HEATER CONTROL PART
CHG-216
(OPTION)
W401 7Z CRD1508※
WHT.T
R4
R3
R2
120Ω
×4
30W
R1
330Ω
30W ×1
R1
B101
1 0 J1
MOTOR
B3P-VH
P1502
WC1
R2
1.2kΩ
30W
AC100V
MOTOR DRIVER
CBD-2001
R1
1.2kΩ
30W
CFA-253
BRAKE CIRCUIT
(W304)
ZCRD1314※
(W307)
ZCRD1547※
J 1905
P1905
1-350209-0
P1911
J 1911
(W309)
ZCRD1538※
BRAKE CIRCUIT B
CFA-260
BRAKE CIRCUIT A
CFA-259
1-350210-0
P1921
J1921
(W310)
ZCRD1539※
CCB-655
J1903
P1903
J 1505
1.R1
PC1501
2.NC
B201 H-7EPRD 0035 3.R2
B2P-VH
IL-2P
BRAKE CONTROL CIRCUIT
P1503
MOTOR
H-7B DRD0050
CBP-203
Xﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄ
Fig B-21: Interconnection Diagram of NKE-1129 (AC110V)
TB105
UTH
（100W）
(W308)
ZCRD1548※
P1941 J 1941
1.+12V
2.NC
3.+12VE
S3B-XH-A
1.VERR1
2.E
J1912
P1912
（W305)
ZCRD1455※
1.MU2
2.NC
3.MV2
4.NC
5.NC
6.GND
2.N
WHT
BLK
WHT
BRN
P82
BLU
RED
BLK
NJU-85
BLK.T
WHT
SAFETY SWITCH CSD-655
YEL
BLU
SHIELD
WHT
BLK BLK
（W303) ZCRD1278※
S.G .
J82
BLU 1
RED
BLK
S.G.
PM
NKE-1129PM (AC100V)
空中線機内接続図
B －24
WHT.T TH101
CAX-12
3.BLK
TR101
WHT.T
SCANNER UNIT INTERCONNECTION
J1504
P1504
1.BKS1
2.BKS2
1.VERR
2.E
1.VERR
2.E
1.M1
2.NC
3.M2
4.NC
5.M3
J1502
TB104
PTI
PTE
LVR
PMS
TXI
TXE
VERR1
ZCRD1280※
1.BKH1
2.NC
3.BKH2
B6P-VH
1.S1
2.S2
3.S3
4.S4
5.S5
6.S6
J1503
TRANSCEIVER UNIT
TRANSCEIVER UNIT TRANSCEIVER UNIT
1.P
2.NC
3.N
1.RED
1.P
B.6.5
B.6 Interconnection Diagram of Scanner Unit
B.DRAWINGS
JMA-9100 Instruction Manual
1 0P1
NKE-1129 (AC220V)
TB103
U1
V1
W1
+12V
C2
ΦZE
ΦZ
ΦA
ΦB
（W301) ZCRD1285※
RED.T
S101
S-32
RED
S.G.
C102
2200p
50V
RED.T
S.G.
C101 +
1000μ
16V
BLK.T
SE
B102
RED
ENCORDER CHT-71A1
J81 P81
AC100V
（W302) ZCRD1286※
HEATER CONTROL PART
CHG-216
(OPTION)
W401 7Z CRD1508※
WHT.T
R4
R3
R2
120Ω
×4
30W
R1
330Ω
30W ×1
R1
B101
1 0 J1
MOTOR
B3P-VH
P1502
WC1
R2
1.2kΩ
30W
AC220V
MOTOR DRIVER
CBD-2000
R1
1.2kΩ
30W
CFA-253
BRAKE CIRCUIT
(W304)
ZCRD1314※
(W307)
ZCRD1547※
J 1905
P1905
1-350209-0
P1911
J 1911
(W309)
ZCRD1538※
BRAKE CIRCUIT B
CFA-260
BRAKE CIRCUIT A
CFA-259
1-350210-0
P1921
J1921
(W310)
ZCRD1539※
CCB-655
J1903
P1903
J 1505
1.R1
PC1501
2.NC
B201 H-7EPRD 0034 3.R2
B2P-VH
IL-2P
BRAKE CONTROL CIRCUIT
P1503
MOTOR
H-7B DRD0050
CBP-203
Xﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄ
Fig B-22: Interconnection Diagram of NKE-1129 (AC220V)
TB105
UTH
（100W）
(W308)
ZCRD1548※
P1941 J 1941
1.+12V
2.NC
3.+12VE
S3B-XH-A
1.VERR1
2.E
J1912
P1912
（W305)
ZCRD1455※
1.MU2
2.NC
3.MV2
4.NC
5.NC
6.GND
2.N
WHT
BLK
WHT
BRN
P82
BLU
RED
BLK
NJU-85
BLK.T
WHT
SAFETY SWITCH CSD-655
YEL
BLU
SHIELD
WHT
BLK BLK
（W303) ZCRD1278※
S.G .
J82
BLU 1
RED
BLK
S.G.
PM
NKE-1129PM (AC220V)
空中線機内接続図
B －25
WHT.T TH101
CAX-12
3.BLK
TR101
WHT.T
SCANNER UNIT INTERCONNECTION
J1504
P1504
1.BKS1
2.BKS2
1.VERR
2.E
1.VERR
2.E
1.M1
2.NC
3.M2
4.NC
5.M3
J1502
TB104
PTI
PTE
LVR
PMS
TXI
TXE
VERR1
ZCRD1280※
1.BKH1
2.NC
3.BKH2
B6P-VH
1.S1
2.S2
3.S3
4.S4
5.S5
6.S6
J1503
TRANSCEIVER UNIT
TRANSCEIVER UNIT TRANSCEIVER UNIT
1.P
2.NC
3.N
1.RED
1.P
B.6.6
B.6 Interconnection Diagram of Scanner Unit
B.DRAWINGS
JMA-9100 Instruction Manual
1 0P1
NTG-3225
B.6.7
(W014)
ZCRD1241※
BM15B-XASS-TE
J101
RECEIVER CIRCUIT
CMA-866A
RECEIVER UNIT NRG-162A
P3001
P1109
P1110
IL-4P
J1109
IL-G -11P
J1191
IL-G-8P
J1110
IL-G-6P
T/R CONTROL CIRCUIT
CMC-1205R
Ａ302
NJS6926
1.SHORT
2.MAGI
3.X1
4.X2
5.TI
6.TIE
7.+15V
8.GND
9.NC
10.NC
11.NC
12.NC
1.HMCNT
2.+15V
3.GND
1.+15V
2.+12V
3.G ND
4.GND
5.-15V
6.10V
7.10VE
8.+5V
J13
1.MCT
2.MBK
3.TISTOP
4.GND
5.MPS
6.MIER
IL-G-2P
J1105
NJS6930
Ａ301
P1111
P1118
P1103
P1104
②
②
Ａ104
NJC9952
ANTENNA
FILTER
A103
NJC4002
DUMMY
①
③
①
Ａ102
NJC 3901M
③
Ａ101
NJC 3901M
MODULATOR UNIT
NMA-552
J2102
P2101
W201
ZCRD1246※
P1002
350209-1
J4
J1002
1586514-2
350209-1
J5
P3
(W106)
ZC RD1245※
(W103)
ZCRD1242※
(W104)
ZCRD1243※
CMB-405
MAG
T1
S.G.
Ｖ101
M1568BS
H-7LPRD0122
C201
0.01UF 1KV
C 202
0.22UF 200V
S.G.
PULSE TRANS
P1202
J 1202
B3P-NV
(W302)
ZCRD1249※
TB202
S.G.
P1201
B4P-VH
J1201
J1212
1.HMCNT
1.VERR
2.+15V
2.E
3.GND
RE LAY FILTER CIRCUIT
CSC-656
PC1201
IL-3P
MODULATOR UNIT
INTERCONNECTION
J1001
B02P-NV(LF)(SN）
J3
POWER SUPPLY CIRCUIT
CBD-1682A
350428-1
1.M+
2.M-
IL-10P
1.SHORT
2.MAG I
No.2
3.X1
MODULATOR
No.1
4.X2
CIRCUIT
5.TI
6.TIE
CPA-264
7.+15V
J2103
8.G ND
350209-2
J2101
9.NC
1.X1
1586514-2 2.X2
10.NC
1.+15V
2.+12V
3.+8V
4.GND
5.-15V
6.10V
7.10VE
8.+5V
(W003)
ZC RD 1234※
P2102
(W004)
ZC RD 1235※
P1004
P1003
(W005)
ZCRD1236※
(W006)
ZCRD1237※
1.MCT
2.MBK
3.HSP
4.HTER
5.TISTOP
6.C2
7.G ND
8.MPS
9.MIER
S.G.
220pF×5
CFR-229
MAG FILTER
CIRCUIT
S.G.
(W301)
ZC RD 1248※
(W303) ZCRD1483※
NTG-3225
送受信機機内接続図
Fig B-23: Interconnection Diagram of NTG-3225
(W001)
ZCRD1233※
J1
MSTBA2.5/11-G
IL-G-4P
1.TIY
2.TIYE
3.BP
4.BPE
5.BZ
6.BZE
J2
1.VD
2.VDE
3.MTR+
4.MTR-
TB101
J1113 J1114
IL-G -3P
DISPLAY
UNIT
V0
J1112
IL-G-3P
ANTENNA
U0
V0
1.BP+
2.BP3.BZ +
4.BZ 5.TRIG +
6.TRIG 7.MTR+
8.MTR9.MTRE
10.VD+
11.VD-
IL-G-9P
(W007) ZCRD1238※
HC3L2
(W203) ZCRD1247※
DISPLAY UNIT
TRANSCEIVER UNIT INTERCONNECTION
CMK-593
BLK
U0
IL-3P
B －26
CD201
CD202
MD-12N1 MD-12N1
IL-2P
R202
2.7KΩ
1/2W
(W105)
ZCRD1244※
P1212
ｷ
1.MU2
2.GND
3.MV2
1.U1
2.NC
3.V1
4.NC
RED
ﾐﾄﾞﾘ
P1211
J 1211
1.MH
2.NC
3.MN
BLK.T
1.MH
2.NC
3.MN
2.1A
1.2A
D.L
(W008) ZC RD1239※
IL-6P
1.φ Z
2.φ ZE
3.φA
4.φ B
5.+12V
6.G ND
3L1
2.1A
1.2A
IL -G-12P
J1118
J1103
PIN
P1105
TB203
ANTENNA
+48VG
J1003
J1004
B8P-SHF
B9P-SHF
+48V
J1111
B3P-SHF
B8P-SHF
R201
150Ω
8W
V1
BLK
V1
IL-G -5P
1.+12V
2.GND
3.FAN_ERR2
C 203
0.22UF
200V
U1
RED
U1
J1106
1.+12V
2.GND
3.FAN _ERR1
P2103
2.1A
1.2A
RED.T +48V
WHT.T +48VG
50/60ｋW
3L1
J8
(W013) ZCRD1240※
TB204
VERR
I L-8P
3L2
ANTENNA
PTI
PTE
LVR
PMS
TXI
TXE
P101
P8
TB201
1.HTER1
2.HVGATE1
3.TISTOP1
4.GND
5.CNT
6.+5V
7.+15V
8.STABY_REQ
9.NC
H-7ZCRD####*:
“#” means specification document No.
“*” means revision of the specfication document.
+12V
C2
φZE
φZ
φA
φB
1.PW1
2.PW2
3.PW3
4.+24V
5.GND
BZ+
MTR+
MTRMTRE
J1104
1.RXD
2.TXD
3.+5V
4.GND
BP+
B6P-SHF
1.MONI
2.GS
3.GSE
4.TGT
5.TGTE
6.TNL
7.-15V
8.TNI
9.+15V
10.GND
11.TRG2
BP -/ BZ-
DISPLAY UNIT
VD+
VD-
1.+12V
2.C 2
RED
WHT
1.BS3
2.BS2
3.BS1
4.TNC
5.+5V
6.-15V
7.+15V
8.GND
9.TGT
10.TGTE
11.TNI
12.VD_DC
13.TNL
14.VDE
15.VD
1.BS3
2.BS2
3.BS1
4.TNC
5.MicPS
6.VDINE
7.VDIN
8.+5V
1.PTI
2.PTE
3.LVR
4.PMS
5.GND
6.TXI
7.TXE
8.NC
TRIG+
TRIG-
B.6 Interconnection Diagram of Scanner Unit
B.DRAWINGS
JMA-9100 Instruction Manual
NKE-1130 (AC110V)
SE
B102
IL-7P
J102
IF CIRCUIT CAE-499
IL-9P
J101
P3002
P1110
CAF-595
RF CIRCUIT
CMA-902
R ECEIRVER UNIT
INTERCONN ECTION
IL-G -3P
J1114
IL-4P
1.SHORT
2.MAGI
3.X1
4.X2
5.TI
6.TIE
7.+15V
8.G ND
9.NC
10.NC
11.NC
12.NC
1.HMCNT
2.+15V
3.G ND
J1113
1.MCT
2.MBK
3.TISTOP
4.GND
5.MPS
6.MIE R
1.+15V
2.+12V
3.G ND
4.G ND
5.-15V
6.10V
7.10VE
8.+5V
IL -G-3P
Ａ301
NJS6318
P1111
P1118
P1103
P1104
②
ANTTENA
FILTER
DUMMY
③
①
③
J2102
J4
350209-1
P1002
②
Ａ102
H-7ANRD0018
P2101
J3
(W106)
Z CRD1321※
MAG
T201
C 201
0.01UF 1KV
PULSE
TRANS
S.G.
Ｖ101
M1555
S.G.
(W308)
ZC RD1542※
H-7LPRD0122
C202
0.22UF 200V
CSD-656
SAFETY SWITCH
IL-2P
(W305)
ZC RD 1456※
J1212
1.VERR1
2.E
P1201
B4P-VH
J1201
3.MV2
S.G.
330 Ω
3 0W ×1
R1
J 1505
P1911
J1911
1-350209-0
B3P-VH
1.R1
2.NC
3.R2
PC 1501
B201 H-7EPRD0035
B2P-VH
B101
MOTOR
R2
R1
1.2kΩ
30W
CFA-255
BRAKE CIRCUIT
CBD-2001
MOTOR DRIVER
AC100V
P1502
WC1
(W304)
ZCRD1316※
(W309)
ZCRD1543※
BLAKE CIRCUIT B
CFA-262
BRAKE CIRCUIT A
CFA-261
R1
120Ω
30W ×4
S.G.
220pF ×5
R2
R3
R4
CCB-655
1-480700-0
1. P
2. N
J1903
IL-2P
P1903
(W307)
ZCRD1541※
(W311)
ZCRD1545※
P1505
J1905
P1905
BRAKE CONTROL CIRCUIT
1-350210-0
(W310)
ZCRD1544※
P1921
J1921
CFR-229
MAG FILTER
CIRCUIT
P1941 J1941
1.+15V
2.NC
3.+15VE
S3B-XH-A
1.VERR1
2.E
J1912
P1511
P1212
P1912
1.HMCNT RELAY FILTER
CIRCUIT B3P-NV
2.+15V
J1202 P1202
CSC-656
3.GND
1.MU2
J1511
PC1201 2.G ND
IL-3P
CMB-406
BLU
WHT
BLK
to CMC-1205R J1112
MODULATOR UNIT
INTERCONNECTION
J1001
J5
B02P-NV(LF)(SN）
1.M+
2.M-
350428-1
350209-1
POWER SUPPLY
CIRCUIT
CBD-1682A
1586514-2
J1002
（W201)
ZCRD1273※
IL-10P
(W103)
1.SHORT
ZCRD1318※
2.MAG I
3.X1
MODULATOR No.2
No.1
4.X2
CIRCUIT
5.TI
CPA-264
6.TIE
(W104)
7.+15V
J2103
ZCRD 1319※
350209-2
8.GND
J2101
9.NC
1.X1
1586514-2 2.X2
10.NC
MODULATOR UNIT
NMA-551
①
Ａ101
NJC3316
(W003)
ZC RD 1268※
P2102
1.+15V
2.+12V
3.+8V
4.GND
5.-15V
6.10V
7.10VE
8.+5V
（W004）
ZCRD1269※
P1004
P1003
(W005)
Z CRD1270※
(W006)
ZCRD1271※
P3
1.MU2
2.NC
3.MV2
4.NC
5.NC
6.G ND
H-7BD RD0049
Fig B-24: Interconnection Diagram of NKE-1130 (AC110V)
RECEIVER UNIT NRG-229
P3001
(W002)
ZCRD1267※
IL-G-9P
J1112
T/R CONTROL CIRCUIT
CMC-1205R
IL-G-11P
J1110
IL -G -8P
J1109
IL-G-6P
J1191
(W001)
ZCRD1266※
P1109
J13
J1
IL-G-4P
MSTBA2.5/11-G
50/60ｋW
1.MCT
2.MBK
3.HSP
4.HTER
5.TISTOP
6.C2
7.GND
8.MPS
9.MIER
(W303)
ZC RD1284※
P1503
MOTOR
CBP-205
B －27
1.TIY
2.TIYE
3.BP
4.BPE
5.BZ
6.BZE
J2
1.VD
2.VDE
3.MTR+
4.MTR-
TB101
1.BP+
2.BP3.BZ +
4.BZ 5.TRIG +
6.TRIG 7.MTR+
8.MTR9.MTRE
10.VD+
11.VD-
J1105
(W302)
Z CRD1453※
(W301)
ZCRD1322※
1.P
2.NC
3.N
NKE-1130PM （AC100V) S30kw, 2ﾕﾆｯﾄ
空中線機内接続図
HEATER CONTROL PART
CHG-215
(OPTION)
1.BKS1
2.BKS2
1.VERR
2.E
1.VERR
2.E
1.M1
2.NC
3.M2
4.NC
5.M3
J1502
J1504
P1504
1.BKH1
2.NC
3.BKH2
B6P-VH
1.S1
2.S2
3.S3
4.S4
5.S5
6.S6
J1503
IL-G-2P
(W203)
ZCRD1274※
W401 7ZCRD1509
WHT.T
TR101
（200W）
BLK.T
P2103
WHT.T
3.BLK
YEL
RED .T
BLK.T
1.RED
CD202
CD 201
MD-12N1 MD-12N1
R202
2.7KΩ
1/2W
R２01
(W105)
150Ω
ZCRD 1320※ 8W
GRN
IL-3P
P1211
J1211
C 203
0.22UF
200V
1.U1
2.NC
3.V1
4.NC
RED.T
IL-G -5P
J1106
(W008)
ZCRD1283※
P1105
UTH
WHT
RED
UTH
P1114
TB102
P1113
(W010)
ZCRD1272※
J 1112
P1112
DISPLAY UNIT
J8
FAN
FAN
SCANNER INTERCONNECTION
CAX-13
S101
S-32F
2.1A
1.2A
IL-G-12P
J1118
B8P-SHF
1.MH
2.NC
3.MN
BLK.T
1.MH
2.NC
3.MN
2.1A
1.2A
J1003
W1
2.1A
1.2A
B8P-SHF
J1004
V1
W1
to CCB-655 J1941
B103
B104
(W308)
ZCRD1542※
S.G.
U1
B9P-SHF
V1
J1111
B3P-SHF
J1103
1.+12V
2.C2
I L-8P
7ZCRD1279※
HT1 0 1
PM
U1
1.+12V
2.GND
3.FAN_ERR1
RED
BLU
YEL
P13
IL-6P
YEL
1.φZ
BLK
2.φZE
BLU
3.φ A
WHT
4.φB
RED
5.+12V
SHIELD
6.GND
(W018)
ZCRD1275※
NJU-84
+48V
+48VG
1.HTER1
2.HVGATE1
3.TISTOP1
4.GND
5.CNT
6.+5V
7.+15V
8.STABY_REQ
9.NC
D.L
+48V
+48VG
1.PW1
2.PW2
3.PW3
4.+24V
5.GND
J1104
1.+12V
2.GND
3.FAN_ERR2
RED
BLU
YEL
B6P-SHF
1.RXD
2.TXD
3.+5V
4.GND
1.TGT
2.TGTE
3.TNL
4.-15V
5.TNI
6.+15V
7.GND
1.MONI
2.GS
3.GSE
4.TGT
5.TGTE
6.TNL
7.-15V
8.TNI
9.+15V
10.GND
11.TRG2
P82 J 82
BLU
1.LVR
RED
2.PMS
BLK
3.E
CHT-71A
ENCODER
1.BS3
2.BS2
3.BS1
4.TNC
5.MPS
6.VDE
7.VD
8.+5V
9.NC
BLK
WHT
BRN
(W017)
DISPLAY UNIT
1.BS3
2.BS2
3.BS1
4.TNC
5.MicPS
6.VDINE
7.VDIN
8.+5V
1.PTI
2.PTE
3.LVR
4.PMS
5.GND
6.TXI
7.TXE
8.NC
WHT
P81 J81
1.PTI
2.PTE
3.TXI
4.TXE
1 0 J1
1 0P1
B.6.8
B.6 Interconnection Diagram of Scanner Unit
B.DRAWINGS
JMA-9100 Instruction Manual
NKE-1130 (AC220V)
SE
B102
IL-7P
J102
IF CIRCUIT CAE-499
IL-9P
J101
P3002
P1110
CAF-595
RF CIRCUIT
CMA-902
R ECEIRVER UNIT
INTERCONN ECTION
IL-G -3P
J1114
IL-4P
1.SHORT
2.MAGI
3.X1
4.X2
5.TI
6.TIE
7.+15V
8.G ND
9.NC
10.NC
11.NC
12.NC
1.HMCNT
2.+15V
3.G ND
J1113
1.MCT
2.MBK
3.TISTOP
4.GND
5.MPS
6.MIE R
1.+15V
2.+12V
3.G ND
4.G ND
5.-15V
6.10V
7.10VE
8.+5V
IL -G-3P
Ａ301
NJS6318
P1111
P1118
P1103
P1104
②
ANTTENA
FILTER
DUMMY
③
①
③
J2102
J4
350209-1
P1002
②
Ａ102
H-7ANRD0018
P2101
J3
(W106)
Z CRD1321※
MAG
T201
C 201
0.01UF 1KV
PULSE
TRANS
S.G.
Ｖ101
M1555
S.G.
(W308)
ZC RD1542※
H-7LPRD0122
C202
0.22UF 200V
CSD-656
SAFETY SWITCH
IL-2P
(W305)
ZC RD 1456※
J1212
1.VERR1
2.E
P1201
B4P-VH
J1201
3.MV2
S.G.
330 Ω
3 0W ×1
R1
J 1505
P1911
J1911
1-350209-0
B3P-VH
1.R1
2.NC
3.R2
PC 1501
B201 H-7EPRD0034
B2P-VH
B101
MOTOR
R2
R1
1.2kΩ
30W
CFA-255
BRAKE CIRCUIT
CBD-2000
MOTOR DRIVER
AC220V
P1502
WC1
(W304)
ZCRD1316※
(W309)
ZCRD1543※
BLAKE CIRCUIT B
CFA-262
BRAKE CIRCUIT A
CFA-261
R1
120Ω
30W ×4
S.G.
220pF ×5
R2
R3
R4
CCB-655
1-480700-0
1. P
2. N
J1903
IL-2P
P1903
(W307)
ZCRD1541※
(W311)
ZCRD1545※
P1505
J1905
P1905
BRAKE CONTROL CIRCUIT
1-350210-0
(W310)
ZCRD1544※
P1921
J1921
CFR-229
MAG FILTER
CIRCUIT
P1941 J1941
1.+15V
2.NC
3.+15VE
S3B-XH-A
1.VERR1
2.E
J1912
P1511
P1212
P1912
1.HMCNT RELAY FILTER
CIRCUIT B3P-NV
2.+15V
J1202 P1202
CSC-656
3.GND
1.MU2
J1511
PC1201 2.G ND
IL-3P
CMB-406
BLU
WHT
BLK
to CMC-1205R J1112
MODULATOR UNIT
INTERCONNECTION
J1001
J5
B02P-NV(LF)(SN）
1.M+
2.M-
350428-1
350209-1
POWER SUPPLY
CIRCUIT
CBD-1682A
1586514-2
J1002
（W201)
ZCRD1273※
IL-10P
(W103)
1.SHORT
ZCRD1318※
2.MAG I
3.X1
MODULATOR No.2
No.1
4.X2
CIRCUIT
5.TI
CPA-264
6.TIE
(W104)
7.+15V
J2103
ZCRD 1319※
350209-2
8.GND
J2101
9.NC
1.X1
1586514-2 2.X2
10.NC
MODULATOR UNIT
NMA-551
①
Ａ101
NJC3316
(W003)
ZC RD 1268※
P2102
1.+15V
2.+12V
3.+8V
4.GND
5.-15V
6.10V
7.10VE
8.+5V
（W004）
ZCRD1269※
P1004
P1003
(W005)
Z CRD1270※
(W006)
ZCRD1271※
P3
1.MU2
2.NC
3.MV2
4.NC
5.NC
6.G ND
H-7BD RD0049
Fig B-25: Interconnection Diagram of NKE-1130 (AC220V)
RECEIVER UNIT NRG-229
P3001
(W002)
ZCRD1267※
IL-G-9P
J1112
T/R CONTROL CIRCUIT
CMC-1205R
IL-G-11P
J1110
IL -G -8P
J1109
IL-G-6P
J1191
(W001)
ZCRD1266※
P1109
J13
J1
IL-G-4P
MSTBA2.5/11-G
50/60ｋW
1.MCT
2.MBK
3.HSP
4.HTER
5.TISTOP
6.C2
7.GND
8.MPS
9.MIER
(W303)
ZC RD1284※
P1503
MOTOR
CBP-205
B －28
1.TIY
2.TIYE
3.BP
4.BPE
5.BZ
6.BZE
J2
1.VD
2.VDE
3.MTR+
4.MTR-
TB101
1.BP+
2.BP3.BZ +
4.BZ 5.TRIG +
6.TRIG 7.MTR+
8.MTR9.MTRE
10.VD+
11.VD-
J1105
(W302)
Z CRD1453※
(W301)
ZCRD1322※
1.P
2.NC
3.N
NKE-1130PM （AC220V) S30kw, 2ﾕﾆｯﾄ
空中線機内接続図
HEATER CONTROL PART
CHG-215
(OPTION)
1.BKS1
2.BKS2
1.VERR
2.E
1.VERR
2.E
1.M1
2.NC
3.M2
4.NC
5.M3
J1502
J1504
P1504
1.BKH1
2.NC
3.BKH2
B6P-VH
1.S1
2.S2
3.S3
4.S4
5.S5
6.S6
J1503
IL-G-2P
(W203)
ZCRD1274※
W401 7ZCRD1509
WHT.T
TR101
（200W）
BLK.T
P2103
WHT.T
3.BLK
YEL
RED .T
BLK.T
1.RED
CD202
CD 201
MD-12N1 MD-12N1
R202
2.7KΩ
1/2W
R２01
(W105)
150Ω
ZCRD 1320※ 8W
GRN
IL-3P
P1211
J1211
C 203
0.22UF
200V
1.U1
2.NC
3.V1
4.NC
RED.T
IL-G -5P
J1106
(W008)
ZCRD1283※
P1105
UTH
WHT
RED
UTH
P1114
TB102
P1113
(W010)
ZCRD1272※
J 1112
P1112
DISPLAY UNIT
J8
FAN
FAN
SCANNER INTERCONNECTION
CAX-13
S101
S-32F
2.1A
1.2A
IL-G-12P
J1118
B8P-SHF
1.MH
2.NC
3.MN
BLK.T
1.MH
2.NC
3.MN
2.1A
1.2A
J1003
W1
2.1A
1.2A
B8P-SHF
J1004
V1
W1
to CCB-655 J1941
B103
(W308) B104
ZCRD1542※
S.G.
U1
B9P-SHF
V1
J1111
B3P-SHF
J1103
1.+12V
2.C2
I L-8P
7ZCRD1279※
HT1 0 1
PM
U1
1.+12V
2.GND
3.FAN_ERR1
RED
BLU
YEL
P13
IL-6P
YEL
1.φZ
BLK
2.φZE
BLU
3.φ A
WHT
4.φB
RED
5.+12V
SHIELD
6.GND
(W018)
ZCRD1275※
NJU-84
+48V
+48VG
1.HTER1
2.HVGATE1
3.TISTOP1
4.GND
5.CNT
6.+5V
7.+15V
8.STABY_REQ
9.NC
D.L
+48V
+48VG
1.PW1
2.PW2
3.PW3
4.+24V
5.GND
J1104
1.+12V
2.GND
3.FAN_ERR2
RED
BLU
YEL
B6P-SHF
1.RXD
2.TXD
3.+5V
4.GND
1.TGT
2.TGTE
3.TNL
4.-15V
5.TNI
6.+15V
7.GND
1.MONI
2.GS
3.GSE
4.TGT
5.TGTE
6.TNL
7.-15V
8.TNI
9.+15V
10.GND
11.TRG2
P82 J 82
BLU
1.LVR
RED
2.PMS
BLK
3.E
CHT-71A
ENCODER
1.BS3
2.BS2
3.BS1
4.TNC
5.MPS
6.VDE
7.VD
8.+5V
9.NC
BLK
WHT
BRN
(W017)
DISPLAY UNIT
1.BS3
2.BS2
3.BS1
4.TNC
5.MicPS
6.VDINE
7.VDIN
8.+5V
1.PTI
2.PTE
3.LVR
4.PMS
5.GND
6.TXI
7.TXE
8.NC
WHT
P81 J81
1.PTI
2.PTE
3.TXI
4.TXE
1 0 J1
1 0P1
B.6.9
B.6 Interconnection Diagram of Scanner Unit
B.DRAWINGS
JMA-9100 Instruction Manual
NKE-1139 (AC110V)
S101
S-32
C102
2200p
50V
WHT.T
（100W）
WHT.T TR101
C101 +
1000μ
16V
TH101
W401 7ZCRD1509
（W301) ZCRD1287※ RED
RED.T
BLK.T
RED
WHT
RED.T
BLK.T
（W305) ZCRD1457※
（W302) ZCRD1288※
HEATER CONTROL
PART
CHG -215
(OPTION)
(W308)
ZCRD1553※
P1941 J1941
1.+12V
2.NC
3.+12VE
S3B-XH-A
B2PS-VH
1.VE RR1
2.E
J1912
P1912
R4
R3
R2
120Ω
×4
30W
R1
330Ω
30W ×1
R1
P1911
J1911
1-350209-0
J1905
P1905
B3P-VH
PC1501
1.R1
B201 H-7EPRD0035 2.NC
3.R2
1 0 J1
H-7BDRD0049
B101
MOTOR
P1502
WC1
R2
R1
1.2kΩ 1.2kΩ
30W
30W
AC100V
MOTOR DRIVER
CBD-2001
CFA-255
BRAKE CIRCUIT
(W304)
ZCRD1316※
(W309)
ZCRD1543※
BRAKE CIRCUIT B
CFA-262
BRAKE CIRCUIT A
CFA-261
P1921
J1921
(W310)
ZCRD1544※
1-350210-0
CCB-655
J1903
P1903
J1505
B2P-VH
(W307)
ZCRD1552※
IL-2P
BRAKE CONTROL CIRCUIT
2.N
SE
B102
S.G.
1.MU2
2.NC
3.MV2
4.NC
5.NC
6.GND
P1503
MOTOR
CBP-205
Fig B-26: Interconnection Diagram of NKE-1139 (AC110V)
SAFETY SWITCH CSD-657
WHT
RED
S.G.
SCANNER INTERCONNECTION
CAX-14
1.RED
TB103
U1
V1
UTH
BLK
YEL
ENCODER CHT-71A1
J81 P81
WHT
BLK
WHT
BRN
P82
BL U
RE D
BLK
NJU-84
NKE-1139PM (AC100V) Sﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄ
空中線機内接続図
B －29
1.BKS1
2.BKS2
1.VERR
2.E
1.VERR
2.E
1.M1
2.NC
3.M2
4.NC
5.M3
J1502
BLU
SHIELD
WHT
S.G.
（W303) ZCRD1276※
J82
S.G.
PM
J 1504
P1504
1.BKH1
2.NC
3.BKH2
1.P
2.NC
3.N
3.BLK
1.S1
2.S2
3.S3
4.S4 B6P-VH
5.S5
6.S6
J1503
+12V
C2
ΦZE
ΦZ
ΦA
ΦB
TB104
PTI
PTE
LVR
PMS
TXI
TXE
VERR1
ZCRD1179※
AC100V
TRANSCEIVER UNIT
TRANSCEIVER UNIT
TRANSCEIVER UNIT
1.P
B.6.10
B.6 Interconnection Diagram of Scanner Unit
B.DRAWINGS
JMA-9100 Instruction Manual
BLK
BLK
1 0P1
NKE-1139 (AC220V)
S101
S-32
C102
2200p
50V
WHT.T
（100W）
WHT.T TR101
C101 +
1000μ
16V
TH101
W401 7ZCRD1509
（W301) ZCRD1287※ RED
RED.T
BLK.T
RED
WHT
RED.T
BLK.T
（W305) ZCRD1457※
（W302) ZCRD1288※
HEATER CONTROL
PART
CHG -215
(OPTION)
(W308)
ZCRD1553※
P1941 J1941
1.+12V
2.NC
3.+12VE
S3B-XH-A
B2PS-VH
1.VERR
2.E
J1912
P1912
R4
R3
R2
120Ω
×4
30W
R1
330Ω
30W ×1
R1
P1911
J1911
1-350209-0
J1905
P1905
B3P-VH
PC1501
1.R1
B201 H-7EPRD0034 2.NC
3.R2
1 0 J1
H-7BDRD0049
B101
MOTOR
P1502
WC1
R2
R1
1.2kΩ 1.2kΩ
30W
30W
AC220V
MOTOR DRIVER
CBD-2000
CFA-255
BRAKE CIRCUIT
(W304)
ZCRD1316※
(W309)
ZCRD1543※
BRAKE CIRCUIT B
CFA-262
BRAKE CIRCUIT A
CFA-261
P1921
J1921
(W310)
ZCRD1544※
1-350210-0
CCB-655
J1903
P1903
J1505
B2P-VH
(W307)
ZCRD1552※
IL-2P
BRAKE CONTROL CIRCUIT
2.N
SE
B102
S.G.
1.MU2
2.NC
3.MV2
4.NC
5.NC
6.GND
P1503
MOTOR
CBP-205
Fig B-27: Interconnection Diagram of NKE-1139 (AC220V)
SAFETY SWITCH CSD-657
WHT
RED
S.G.
SCANNER INTERCONNECTION
CAX-14
1.RED
TB103
U1
V1
UTH
BLK
YEL
ENCODER CHT-71A1
J81 P81
WHT
BLK
WHT
BRN
P82
BL U
RE D
BLK
NJU-84
NKE-1139PM (AC220V) Sﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄ
空中線機内接続図
B －30
1.BKS1
2.BKS2
1.VERR
2.E
1.VERR
2.E
1.M1
2.NC
3.M2
4.NC
5.M3
J1502
BLU
SHIELD
WHT
S.G.
（W303) ZCRD1276※
J82
S.G.
PM
J 1504
P1504
1.BKH1
2.NC
3.BKH2
1.P
2.NC
3.N
3.BLK
1.S1
2.S2
3.S3
4.S4 B6P-VH
5.S5
6.S6
J1503
+12V
C2
ΦZE
ΦZ
ΦA
ΦB
TB104
PTI
PTE
LVR
PMS
TXI
TXE
VERR1
ZCRD1179※
AC100V
TRANSCEIVER UNIT
TRANSCEIVER UNIT
TRANSCEIVER UNIT
1.P
B.6.11
B.6 Interconnection Diagram of Scanner Unit
B.DRAWINGS
JMA-9100 Instruction Manual
BLK
BLK
1 0P1
NTG-3230
B.6.12
(W014)
ZCRD1226※
IL-9P
J101
IL-7P
J102
IF CIRCUIT CAE-499
RECEIVER UNIT NRG-229
J1
P3001
(W002)
ZC RD1218※
P3002
P1110
IL-4P
J1191
CMA-902
RF CIRCUIT
CAF-595
IL-G-3P
J13
1.MCT
2.MBK
3.TI STOP
4.GND
5.MPS
6.MIER
1.+15V
2.+12V
3.GND
4.GND
5.-15V
6.10V
7.10VE
8.+5V
1.HMCNT
2.+15V
3.GND
1.SHORT
2.MAGI
3.X1
4.X2
5.TI
6.TI E
7.+15V
8.GND
9.N C
10.NC
11.NC
12.NC
RECEIVER UN IT
INTERCONNECTION
IL-G-3P
J1113 J1114
T/R CONTROL CIRCUIT
CMC-1205R
IL-G -11P
J1110
IL-G-8P
J1109
IL-G-6P
MSTBA2.5/11-G
IL-G -4P
1.TIY
2.TIYE
3.BP
4.BPE
5.BZ
6.BZE
J2
1.VD
2.VD E
3.MTR+
4.MTR-
TB101
IL -G -9P
J1112
Ａ203
TL378A
P1111
P1118
P1103
P1104
③
FILTER
ANTENNA
①
Ａ201
NJC 3317
②
Ａ205
DUMMY
③
①
H-7ANRD0018
②
MODULATOR UNIT
NMA-553
J2102
W201
ZCRD1231※
P1002
350209-1
J4
P2101
1586514-2
J1002
(W106)
Z CRD1230※
(W103)
ZC RD 1227※
(W104)
ZC RD 1228※
CMB-407
J5
B02P-NV(LF)(SN）
J3
P3
MAG
T1
C201
0.01UF 1KV
H-7LPRD 0122
C202
0.22UF 200V
S.G.
PULSE TRANS
P1202
J1202
B3P-NV
(W302)
Z CRD1216※
TB202
Ｖ101
M1555
S.G.
S.G.
P1201
B4P-VH
J1201
J1212
1.HMCN T
1.VERR
2.+15V
2.E
3.GND
RELAY FILTER CIRC UIT
CSC-656
PC1201
IL-3P
MODULATOR UNIT
INTERCONNECTION
J1001
350209-1
POWER SUPPLY CIRCUIT
CBD-1682A
350428-1
1.M+
2.M-
IL-10P
1.SHORT
2.MAGI
No.2
3.X1
No.1
4.X2
5.TI MODULATOR CIRCUIT
6.TIE
CPA-264 J2103
7.+15V
8.GND
350209-2
J2101
9.NC
1.X1
1586514-2 2.X2
10.NC
1.+15V
2.+12V
3.+8V
4.G ND
5.-15V
6.10V
7.10VE
8.+5V
(W003)
ZCRD1219※
P2102
（W004）
ZCRD1220※
P1004
P1003
(W005)
ZC RD1221※
(W006)
ZC RD1222※
1.MCT
2.MBK
3.HSP
4.HTER
5.TI STOP
6.C2
7.GND
8.MPS
9.MIER
S.G.
220pF×5
CFR-229
MAG FILTER CIRCUIT
(W301)
ZC RD1215※
S.G.
(W303) ZCRD1484※
B －31
(W001)
ZC RD 1217※
P1109
P101
1.BP+
2.BP3.BZ+
4.BZ5.TRIG+
6.TRIG7.MTR+
8.MTR9.MTRE
10.VD+
11.VD-
J1105
I L-G -2P
(W203) ZCRD1232※
DISPLAY
UNIT
V0
SCANNER
UNIT
V0
IL-G-5P
HC3L2
(W007) ZCRD1223※
3L1
U0
Fig B-28: Interconnection Diagram of NTG-3230
YEL
U0
TRANSCEIVER UNIT INTERCONNECTION
CMK-594
NTG-3230
送受信機機内接続図
P1212
CD201
CD202
MD-12N1 MD-12N1
IL-2P
R202
2.7KΩ
1/2W
R201
150Ω
(W105)
ZCRD 1229※ 8W
1.MU2
2.GND
3.MV2
1.U1
2.NC
3.V1
4.NC
RED
V1
BLK
IL-3P
1.MH
2.NC
3.MN
BLK.T
1.MH
2.NC
3.MN
2.1A
1.2A
J1003
J1004
DISPLAY
UNIT
2.1A
1.2A
TRHPL
(W008) ZCRD1224※
IL-6P
1.φZ
2.φZE
3.φ A
4.φB
5.+12V
6.GND
P1105
TB203
SCANNER
UNIT
+48VG
IL -G-12P
GRN
P1211
J 1211
B8P-SHF
B9P-SHF
+48V
J1111
J1118
B8P-SHF
B3P-SHF
J1103
B6P-SHF
C203
0.22UF
200V
BLK
U1
V1
RED
U1
J1106
3L1
1.+12V
2.GND
3.FAN_ERR2
P2103
2.1A
1.2A
+48V
+48VG
RED.T
WHT.T
IL-8P
(W013) ZCRD1225※
TB204
SCANNER UNIT
J8
3L2
1.HTER1
2.HVGATE1
3.TISTOP1
4.GND
5.CNT
6.+5V
7.+15V
8.STABY_REQ
9.NC
VERR
1.+12V
2.GND
3.FAN _ERR1
H-7ZCRD####*:
“#” means specification document No.
“*” means revision of the specfication document.
+12V
C2
φZE
φZ
φA
GND
φB
1.PW1
2.PW2
3.PW3
4.+24V
5.GND
PTI
PTE
LVR
PMS
TXI
TXE
P8
TB201
BP+
J1104
1.RXD
2.TXD
3.+5V
4.GND
1.TGT
2.TGTE
3.TNL
4.-15V
5.TNI
6.+15V
7.GND
1.MONI
2.GS
3.GSE
4.TGT
5.TGTE
6.TNL
7.-15V
8.TNI
9.+15V
10.GND
11.TRG2
BP -/BZ-
DISPLAY UNIT
VD+
VD-
1.+12V
2.C 2
RED
WHT
1.BS3
2.BS2
3.BS1
4.TNC
5.MPS
6.VDE
7.VD
8.+5V
9.NC
1.BS3
2.BS2
3.BS1
4.TNC
5.MicPS
6.VDINE
7.VDIN
8.+5V
BZ+
MTR+
MTRMTRE
1.PTI
2.PTE
3.LVR
4.PMS
5.GND
6.TXI
7.TXE
8.NC
TRIG+
TRIG-
B.6 Interconnection Diagram of Scanner Unit
B.DRAWINGS
JMA-9100 Instruction Manual
JMA-9100 Instruction Manual
B.7
B.DRAWINGS
B.7 Terminal Board Connection Diagram
Terminal Board Connection Diagram
B －32
B －33
Fig B-29: Terminal Board Connection Diagram of JMA-9110-6XA/JMA-9110-6XAH
250V -M PYCYS-7
0. 6/ 1kV-D PYCYS-1.5
( NEAREST AP PRO ACH)
ALARM MONITORING
SYSTEM
GYRO
(200P /NM)
0. 6/1kV-D PYCYS-1.5
B LK
5-1 P)
PWR OU T1E
VDOU T1
VDOU T1E
TRIG OU T1
TRIG OU T1E
BPOU T1
BPOU T1E
BZOUT1
BZOUT1E
MTROUT 1+
MTROUT 1MTROUT 1E
17
18
19
20
21
22
23
24
25
26
R ED
PUR
WHT
NA V2RX+
NA V2RX-
(N C)
P1+
12
10
11
(NC)
(N C)
(N C)
S2(N C)
(N C)
S1+
P1(N C)
(N C)
(N C)
TB4801(L O G)
MNTTX +
MNTTX -
HD G RX-
22
AIS_RG
21
22
AISRX+
AISRX-
AISTXAIS_TG
EXEVTAISTX+
20
S3
5/R2
NSKT XHD G RX+
20
21
18
19
JAR PA TXNSKT X+
18
19
16
17
ARPAT XJAR PA TX+
16
17
14
15
AL MRXARPAT X+
14
15
PWR ACKEXEVT+
2/S1
3/S2
AL MRX+
13
PWR ACK+
12
13
SYSACK+
SYSACK-
ARPAAC K+
ARPAAC K-
PWR AL M+
PWR AL M-
SYSALM +
SYSALM +
11
10
AL MTX+
AL MTX-
11
12
LOG RX+
LOG RX-
NA V2TX+
NA V2TX-
10
NA V1RX+
NA V1RX-
NA V1TX-
ARPAAL M-
TB4601(ALA RM)
ARPAAL M+
TB4501(OPTION)
NA V1TX+
WH T-WH T
WH T-YE L
BR N
PWR OU T1
PWR IN1
PWR IN1E
12
13
15
16
MTRIN 1MTRIN 1E
10
11
14
PNK
BLK
ORG
WH T-WH T
T B4701(G YRO)
1/R1
GR Y
BL U
GRN
RED
BPIN1E
BZIN1
BLK
WHT
RED
+48V
+48VG
MTRE
(NC)
MTR+
MTR-
BZ-
BPBZ+
TRIG BP+
FG
ー
FG
FILTER AC IN
WMRST-
ACKOU T+
ACKOU TWMRST+
(NC )
(NC )
27
30
EXφZ2
EXφZ2E
25
26
28
29
EXφB2
EXφB2E
23
24
EXφA2
EXφA2E
ETIY2E
SVD 2E
ETIY2
EXφZ1E
SVD 2
EXφB1E
EXφZ1
EXφA1E
EXφB1
EXφA1
ETIY1
ETIY1E
SVD 1
SVD 1E
ETIY3
ETIY3E
RBVD E
21
22
20
18
19
16
17
14
15
12
13
11
10
B LK
WHT
PUR .T/ BRN.T
B LU.T /GRY .T
TB4401(EXT RAD AR)
RBVD
BA TT IN +
BA TT IN -
CBD -1661 ACOU T1
CBD -1684A TB521
WHT.T/ ORN .T
B LK.T/ SK Y.T
Y EL.T/ PNK.T
WHT
Y EL
GR N
B LK
OR N
CBD -1684A TB522 R ED.T/ GR N .T
13
14
11
12
10
COA XI AL
SHI ELD
VDTRIG +
TB4101(AN T)
VD+
W406 H- 7ZC RD1342 A
( Wir ing is com pleted .)
0.6/1kV-D PYCY-6
COM-
COM+
VDE
VD
J2
1A
2A
J5
1A
2A
J4
BLK
GR N
ORN
SHIE LD
YE L.T/ PNK.T
BLK .T/ SKY .T
AGND
EXBZ
AGND
EXBP
AGND
ETIY
J1
1A
2A
J3
P81
PMS
P82
L VR
T XE
PTE
T XI
PTI
P1
NJU-85
PMS
P2
L VR
TXE
TXI
PTI
PTE
PERFORMANCE
MONITOR
B LK
R ED
B LU
B RN
WHT
(X-BAND 10kW RADAR)
B LK
R ED
B LU
B RN
WHT
W iring of PER FOR MANC E MONITOR
is com pleted .
JMA-9110-6XA/6XAH レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9110-6XA/6XAH
AC100-115V/ AC220-240V 50/60H z 1φ
SHIP’S MAINS
WHT
YEL
C OAXI AL
R ED.T/ GR N. T
PUR. T/ BRN.T
WHT .T/ ORN.T
BLU.T /GRY .T
SCANNER UNIT
NKE-2103-6/6HS
LOG
250V-T TYCS-4
250V-T TYCS-1
CQD-1891
(J RC SUPPL Y)
J4407
RJ -45 L AN
BPIN1
BZIN1E
MTRIN 1+
TRIG IN1
TRIG IN1E
VDIN 1
VDIN 1E
WH T-B LU
GRN
YE L
BLU
T B4201(ISW IN/OU T)
CQD-2097 T ERMIN AL BOARD
19-CORES COMPOSITE CABL E (J RC SUPPL Y)
C FQ-6912-**
B.DRAWINGS
AIS
(NMEA0183)
LOG
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
H -2695110006
(J RC SUPPL Y)
3C-2V x 5 (MAX 30m )
250V-T TYCS-1
H -2695111153
(J RC SUPPL Y)
ECHO
SOU NDER
DGPS
CONNING
DISPLAY
ECDIS
VDR
(INTERSWITC H)
RADAR
B.7.1
C DC4 2 3-1
9 0 4J4 BUS(D
DISPLAY UNIT NCD-4990
JMA-9100 Instruction Manual
B.7 Terminal Board Connection Diagram
JMA-9110-6XA/JMA-9110-6XAH
B －34
250V -M PYCYS-7
0. 6/1kV-D PYCYS-1.5
250V-T TYCS-4
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
0. 6/1kV-D PYCYS-1.5
( NEAREST AP PRO ACH)
ALARM MONITORING
SYSTEM
GYRO
(200P /NM)
LOG
AIS
(NMEA0183)
LOG
ECHO
SOU NDER
DGPS
CONNING
DISPLAY
250V-T TYCS-1
B LK
5-1 P)
BPIN1E
BZIN1
PWR OU T1E
VDOU T1
VDOU T1E
TRIG OU T1
TRIG OU T1E
BPOU T1
BPOU T1E
BZOUT1
BZOUT1E
MTROUT 1+
MTROUT 1MTROUT 1E
17
18
19
20
21
22
23
24
25
26
R ED
PUR
WHT
NA V2RX+
NA V2RX-
MNTTX +
MNTTX -
(N C)
P1+
12
10
11
(NC)
(N C)
(N C)
S2(N C)
(N C)
S1+
P1(N C)
(N C)
(N C)
TB4801(L O G)
AIS_RG
21
22
AISRX+
AISRX-
AISTXAIS_TG
EXEVTAISTX+
20
HD G RX-
22
S3
5/R2
NSKT XHD G RX+
20
21
18
19
JAR PA TXNSKT X+
18
19
16
17
14
15
ARPAT XJAR PA TX+
16
17
AL MRXARPAT X+
14
15
PWR ACKEXEVT+
2/S1
3/S2
AL MRX+
13
PWR ACK+
12
13
SYSACK+
SYSACK-
ARPAAC K+
ARPAAC K-
PWR AL M+
PWR AL M-
SYSALM +
SYSALM +
11
10
AL MTX+
AL MTX-
11
12
LOG RX+
LOG RX-
NA V2TX+
NA V2TX-
10
NA V1RX+
NA V1RX-
NA V1TX-
ARPAAL M-
TB4601(ALA RM)
ARPAAL M+
TB4501(OPTION)
NA V1TX+
WH T-WH T
WH T-YE L
BR N
PWR OU T1
PWR IN1
PWR IN1E
12
13
15
16
MTRIN 1MTRIN 1E
10
11
14
PNK
BLK
ORG
WH T-WH T
T B4701(G YRO)
1/R1
GR Y
BL U
GRN
RED
CQD-1891
(J RC SUPPL Y)
J4407
RJ -45 L AN
BPIN1
BZIN1E
MTRIN 1+
TRIG IN1
TRIG IN1E
VDIN 1
VDIN 1E
WH T-B LU
GRN
YE L
BLU
T B4201(ISW IN/OU T)
TB401
FG
ー
+48V
+48VG
MTRE
(NC)
MTR+
MTR-
BZ-
BPBZ+
TRIG BP+
FILTER AC IN
T B402
WMRST-
ACKOU T+
ACKOU TWMRST+
(NC )
(NC )
27
30
EXφZ2
EXφZ2E
25
26
28
29
EXφB2
EXφB2E
23
24
EXφA2
EXφA2E
ETIY2E
SVD 2E
ETIY2
EXφZ1E
SVD 2
EXφB1E
EXφZ1
EXφA1E
EXφB1
EXφA1
ETIY1
ETIY1E
SVD 1
SVD 1E
ETIY3
ETIY3E
RBVD E
21
22
20
18
19
16
17
14
15
12
13
11
10
B LK
WHT
W405 H -7ZC RD 1341A( JRC SUPPL Y)
Wiring is com pleted.
WHT
B LK
R ED
B LK
WHT
GRN
BLK
WHT
PUR .T/ BRN.T
B LU.T /GRY .T
R ED.T/ GR N .T
WHT.T/ ORN .T
B LK.T/ SK Y.T
Y EL.T/ PNK.T
WHT
Y EL
GR N
B LK
OR N
TB4401(EXT RAD AR)
RBVD
BA TT IN +
BA TT IN -
CBD -1661 ACOU T1
GR N
BLK- BLK
R ED
BLK
13
14
11
12
10
COA XI AL
SHI ELD
VDTRIG +
TB4101(AN T)
VD+
WHT- BLK
WHT
RED
CQD-2097 T ERMIN AL BOARD
W407 H- 7ZC RD1343 A
( JRC SUPPLY)
W408 H- 7ZC RD1344 A
( JRC SUPPLY)
FG
ー
FG
AC100-115V/ AC220-240V 50/60H z 1φ
SHIP’S MAINS
WHT
YEL
C OAXI AL
R ED.T/ GR N. T
PUR. T/ BRN.T
WHT .T/ ORN.T
BLU.T /GRY .T
COM-
COM+
VDE
VD
J2
1A
2A
J5
1A
2A
J4
BLK
GR N
ORN
SHIE LD
YE L.T/ PNK.T
BLK .T/ SKY .T
AGND
EXBZ
AGND
EXBP
AGND
ETIY
J1
1A
2A
J3
SCANNER UNIT
NKE-2103-6/6HS
P81
PMS
P82
L VR
T XE
PTE
T XI
PTI
P1
NJU-85
PMS
P2
L VR
TXE
TXI
PTI
PTE
PERFORMANCE
MONITOR
B LK
R ED
B LU
B RN
WHT
(X-BAND 10kW RADAR)
B LK
R ED
B LU
B RN
WHT
W iring of PER FOR MANC E MONITOR
is com pleted .
JMA-9110-6XA/6XAH レーダー（卓上型） 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9110-6XA/6XAH(desktop)
0.6/1kV-D PYCY-6
NBA-5135
CBD -1684A TB 521
CBD -1684A TB 522
AC/DC CONVERTER UNIT
GRN
B LK
WHT
GRN
B LK-B LK
WHT -B LK
19-CORES COMPOSITE CABL E (J RC SUPPL Y)
C FQ-6912-**
H -2695110006
(J RC SUPPL Y)
3C-2V x 5 (MAX 30m )
250V-T TYCS-1
H -2695111153
(J RC SUPPL Y)
B.DRAWINGS
ECDIS
VDR
(INTERSWITC H)
RADAR
DISPLAY UNIT NCD-4990T
B.7.2
C DC4 2 3-1
9 0 4J4 BUS(D
JMA-9100 Instruction Manual
B.7 Terminal Board Connection Diagram
JMA-9110-6XA/JMA-9110-6XAH (desktop)
Fig B-30: Terminal Board Connection Diagram of JMA-9110-6XA/JMA-9110-6XAH (desktop)
B －35
Fig B-31: Terminal Board Connection Diagram of JMA-9122-6XAH
250V -M PYCYS-7
0. 6/1kV-D PYCYS-1.5
( NEAREST AP PRO ACH)
ALARM MONITORING
SYSTEM
GYRO
(200P /NM)
0. 6/1kV-D PYCYS-1.5
B LK
5-1 P)
PWR OU T1E
VDOU T1
VDOU T1E
TRIG OU T1
TRIG OU T1E
BPOU T1
BPOU T1E
BZOUT1
BZOUT1E
MTROUT 1+
MTROUT 1MTROUT 1E
17
18
19
20
21
22
23
24
25
26
R ED
PUR
WHT
NA V2RX+
NA V2RX-
(N C)
P1+
12
10
11
(NC)
(N C)
(N C)
S2(N C)
(N C)
S1+
P1(N C)
(N C)
(N C)
TB4801(L O G)
MNTTX +
MNTTX -
HD G RX-
22
AIS_RG
21
22
AISRX+
AISRX-
AISTXAIS_TG
20
S3
5/R2
NSKT XHD G RX+
20
21
18
19
16
17
JAR PA TXNSKT X+
18
19
ARPAT XJAR PA TX+
16
17
PWR ACKEXEVT+
EXEVTAISTX+
PWR ACK+
14
15
12
13
SYSACK+
SYSACK-
ARPAAC K+
ARPAAC K-
PWR AL M+
PWR AL M-
SYSALM +
SYSALM +
11
AL MRXARPAT X+
14
15
2/S1
3/S2
AL MRX+
13
10
AL MTX+
AL MTX-
11
12
LOG RX+
LOG RX-
NA V2TX+
NA V2TX-
10
NA V1RX+
NA V1RX-
NA V1TX-
ARPAAL M-
TB4601(ALA RM)
ARPAAL M+
TB4501(OPTION)
NA V1TX+
WH T-WH T
WH T-YE L
BR N
PWR OU T1
PWR IN1
PWR IN1E
12
13
15
16
MTRIN 1MTRIN 1E
10
11
14
PNK
BLK
ORG
WH T-WH T
T B4701(G YRO)
1/R1
GR Y
BL U
GRN
RED
BPIN1E
BZIN1
BLK
WHT
RED
+48V
+48VG
MTRE
(NC)
MTR+
MTR-
BZ-
BPBZ+
TRIG BP+
FG
ー
FG
FILTER AC IN
WMRST-
ACKOU T+
ACKOU TWMRST+
(NC )
(NC )
27
30
EXφZ2
EXφZ2E
25
26
28
29
EXφB2
EXφB2E
23
24
EXφA2
EXφA2E
ETIY2E
SVD 2E
ETIY2
EXφZ1E
SVD 2
EXφB1E
EXφZ1
EXφA1E
EXφB1
EXφA1
ETIY1
ETIY1E
SVD 1
SVD 1E
ETIY3
ETIY3E
RBVD E
21
22
20
18
19
16
17
14
15
12
13
11
10
B LK
WHT
PUR .T/ BRN.T
B LU.T /GRY .T
TB4401(EXT RAD AR)
RBVD
BA TT IN +
BA TT IN -
CBD -1661 ACOU T1
CBD -1684A TB521
WHT.T/ ORN .T
B LK.T/ SK Y.T
Y EL.T/ PNK.T
WHT
Y EL
GR N
B LK
OR N
CBD -1684A TB522 R ED.T/ GR N .T
13
14
11
12
10
COA XI AL
SHI ELD
VDTRIG +
TB4101(AN T)
VD+
W406 H- 7ZC RD1342 A
( Wir ing is com pleted .)
0.6/1kV-D PYCY-6
S TEP- DOWN
T RA NSF OR MER
N BL -175
0.6/1kV-D PYCYS-1.5
C IRCU IT BR EAKER
5A ( SHIP YAR D SUPPLY)
BLK
GR N
ORN
SHIE LD
YE L.T/ PNK.T
BZ-
BZ+
BP-
BP+
TRIG-
TRIG+
0.6/1kV-D PYCYS-1.5
J1
1A
2A
J3
UT H
TB105
BLK .T/ SKY .T
AC220V , 1φ, fo r HEAT ER
SHIP’S MAINS
“D” HEATER OPTION
COM-
COM+
VDE
VD
J2
1A
2A
J5
1A
2A
J4
P81
PMS
P82
L VR
T XE
PTE
T XI
PTI
P1
NJU-85
PMS
P2
L VR
TXE
TXI
PTI
PTE
PERFORMANCE
MONITOR
B LK
R ED
B LU
B RN
WHT
(X-BAND 25kW RADAR)
B LK
R ED
B LU
B RN
WHT
W iring of PER FOR MANC E MONITOR
is com pleted .
JMA-9122-6XAH レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9122-6XAH
AC100-115V/ AC220-240V 50/60H z 1φ
SHIP’S MAINS
0.6/1kV-DPYCY S-1. 5
AC100V,1φ,100W
WHT
YEL
C OAXI AL
R ED.T/ GR N. T
PUR. T/ BRN.T
WHT .T/ ORN.T
BLU.T /GRY .T
SCANNER UNIT
NKE-2254-6HS
LOG
250V-T TYCS-4
250V-T TYCS-1
CQD-1891
(J RC SUPPL Y)
J4407
RJ -45 L AN
BPIN1
BZIN1E
MTRIN 1+
TRIG IN1
TRIG IN1E
VDIN 1
VDIN 1E
WH T-B LU
GRN
YE L
BLU
T B4201(ISW IN/OU T)
CQD-2097 T ERMIN AL BOARD
19-CORES COMPOSITE CABL E (J RC SUPPL Y)
C FQ-6912-**
B.DRAWINGS
AIS
(NMEA0183)
LOG
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
H -2695110006
(J RC SUPPL Y)
3C-2V x 5 (MAX 30m )
250V-T TYCS-1
H -2695111153
(J RC SUPPL Y)
ECHO
SOU NDER
DGPS
CONNING
DISPLAY
ECDIS
VDR
(INTERSWITC H)
RADAR
B.7.3
C DC4 2 3-1
9 0 4J4 BUS(D
DISPLAY UNIT NCD-4990
JMA-9100 Instruction Manual
B.7 Terminal Board Connection Diagram
JMA-9122-6XAH
B －36
Fig B-32: Terminal Board Connection Diagram of JMA-9122-6XAH (desktop)
250V -M PYCYS-7
0.6/1kV-D PYCYS-1.5
250V-T TYCS-4
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
0. 6/1kV-D PYCYS-1.5
( NEAREST AP PRO ACH)
ALARM MONITORING
SYSTEM
GYRO
(200P /NM)
LOG
AIS
(NMEA0183)
LOG
ECHO
SOU NDER
DGPS
CONNING
DISPLAY
250V-T TYCS-1
B LK
BPIN1E
BZIN1
PWR OU T1E
VDOU T1
VDOU T1E
TRIG OU T1
TRIG OU T1E
BPOU T1
BPOU T1E
BZOUT1
BZOUT1E
MTROUT 1+
MTROUT 1MTROUT 1E
17
18
19
20
21
22
23
24
25
26
R ED
PUR
WHT
NA V2RX+
NA V2RX-
(N C)
P1+
12
10
11
(NC)
(N C)
(N C)
S2(N C)
(N C)
S1+
P1(N C)
(N C)
(N C)
TB4801(L O G)
MNTTX +
MNTTX -
HD G RX-
22
AIS_RG
21
22
AISRX+
AISRX-
AISTXAIS_TG
20
S3
5/R2
NSKT XHD G RX+
20
21
18
19
16
17
JAR PA TXNSKT X+
18
19
ARPAT XJAR PA TX+
16
17
PWR ACKEXEVT+
EXEVTAISTX+
PWR ACK+
14
15
12
13
SYSACK+
SYSACK-
ARPAAC K+
ARPAAC K-
PWR AL M+
PWR AL M-
SYSALM +
SYSALM +
11
AL MRXARPAT X+
14
15
2/S1
3/S2
AL MRX+
13
10
AL MTX+
AL MTX-
11
12
LOG RX+
LOG RX-
NA V2TX+
NA V2TX-
10
NA V1RX+
NA V1RX-
NA V1TX-
ARPAAL M-
TB4601(ALA RM)
ARPAAL M+
TB4501(OPTION)
NA V1TX+
WH T-WH T
WH T-YE L
BR N
PWR OU T1
PWR IN1
PWR IN1E
12
13
15
16
MTRIN 1MTRIN 1E
10
11
14
PNK
BLK
ORG
WH T-WH T
T B4701(G YRO)
1/R1
GR Y
BL U
GRN
RED
CQD-1891
(J RC SUPPL Y)
J4407
RJ -45 L AN
BPIN1
BZIN1E
MTRIN 1+
TRIG IN1
TRIG IN1E
VDIN 1
VDIN 1E
WH T-B LU
GRN
YE L
BLU
T B4201(ISW IN/OU T)
TB401
FG
ー
+48V
+48VG
MTRE
(NC)
MTR+
MTR-
BZ-
BPBZ+
TRIG BP+
FILTER AC IN
T B402
WMRST-
ACKOU T+
ACKOU TWMRST+
(NC )
(NC )
27
30
EXφZ2
EXφZ2E
25
26
28
29
EXφB2
EXφB2E
23
24
EXφA2
EXφA2E
ETIY2E
SVD 2E
ETIY2
EXφZ1E
SVD 2
EXφB1E
EXφZ1
EXφA1E
EXφB1
EXφA1
ETIY1
ETIY1E
SVD 1
SVD 1E
ETIY3
ETIY3E
RBVD E
21
22
20
18
19
16
17
14
15
12
13
11
10
B LK
WHT
W405 H -7ZC RD 1341A( JRC SUPPL Y)
Wiring is com pleted.
WHT
B LK
R ED
B LK
WHT
GRN
BLK
WHT
PUR .T/ BRN.T
B LU.T /GRY .T
R ED.T/ GR N .T
WHT.T/ ORN .T
B LK.T/ SK Y.T
Y EL.T/ PNK.T
WHT
Y EL
GR N
B LK
OR N
TB4401(EXT RAD AR)
RBVD
BA TT IN +
BA TT IN -
CBD -1661 ACOU T1
GR N
BLK- BLK
R ED
BLK
13
14
11
12
10
C OA XI AL
SHI ELD
VDTRIG +
TB4101(AN T)
VD+
WHT- BLK
WHT
RED
CQD-2097 T ERMIN AL BOARD
W407 H- 7ZC RD1343 A
( JRC SUPPLY)
W 408 H-7ZC RD134 4A
( JRC SUPPLY)
FG
ー
FG
0.6/1kV-DPYCY S-1. 5
AC100V,1φ,100W
WHT
YEL
C OAXI AL
R ED.T/ GR N. T
PUR. T/ BRN.T
WHT .T/ ORN.T
S TEP- DOWN
T RA NSF OR MER
N BL -175
UT H
TB105
BZ-
BZ+
BP-
BP+
TRIG-
TRIG+
J1
1A
2A
J3
AC220V , 1φ, fo r HEAT ER
SHIP’S MAINS
P81
PMS
P82
L VR
T XE
PTE
T XI
PTI
P1
NJU-85
PMS
P2
L VR
TXE
TXI
PTI
PTE
PERFORMANCE
MONITOR
B LK
R ED
B LU
B RN
WHT
(X-BAND 25kW RADAR)
B LK
R ED
B LU
B RN
WHT
W iring of PER FOR MANC E MONITOR
is com pleted .
JMA-9122-6XAH レーダー（卓上型） 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9122-6XAH(desktop)
AC100-115V/ AC220-240V 50/60H z 1φ
0.6/1kV-D PYCYS-1.5
0.6/1kV-D PY CYS-1.5
BLK
GR N
ORN
SHIE LD
YE L.T/ PNK.T
BLK .T/ SKY .T
“D” HEATER OPTION
COM-
COM+
VDE
VD
J2
1A
2A
J5
1A
2A
J4
SCANNER UNIT
NKE-2254-6HS
BLU.T /GRY .T
C IRCU IT BR EAKER
5A ( SHIP YAR D SUPPLY)
SHIP’S MAINS
CBD -1684A TB 521
0.6/1kV-D PYCY-6
GRN
B LK
WHT
GRN
B LK-B LK
WHT -B LK
CBD -1684A TB 522
NBA-5135
AC/DC CONVERTER UNIT
19-CORES COMPOSITE CABL E (J RC SUPPL Y)
C FQ-6912-**
H -2695110006
(J RC SUPPL Y)
3C-2V x 5 (MAX 30m )
250V-T TYCS-1
H -2695111153
(J RC SUPPL Y)
B.DRAWINGS
ECDIS
VDR
(INTERSWITC H)
RADAR
5-1 P)
DISPLAY UNIT NCD-4990T
B.7.4
C DC4 2 3-1
9 0 4J4 BUS(D
JMA-9100 Instruction Manual
B.7 Terminal Board Connection Diagram
JMA-9122-6XAH (desktop)
B －37
Fig B-33: Terminal Board Connection Diagram of JMA-9122-6XA/9XA
250V -M PYCYS-7
0. 6/1kV-D PYCYS-1.5
( NEAREST AP PRO ACH)
ALARM MONITORING
SYSTEM
GYRO
(200P /NM)
0. 6/1kV-D PYCYS-1.5
B LK
BPIN1E
BZIN1
PWR OU T1E
VDOU T1
VDOU T1E
TRIG OU T1
TRIG OU T1E
BPOU T1
BPOU T1E
BZOUT1
BZOUT1E
MTROUT 1+
MTROUT 1MTROUT 1E
17
18
19
20
21
22
23
24
25
26
R ED
PUR
WHT
NA V2RX+
NA V2RX-
(N C)
P1+
12
10
11
(NC)
(N C)
(N C)
S2(N C)
(N C)
S1+
P1(N C)
(N C)
(N C)
TB4801(L O G)
MNTTX +
MNTTX -
HD G RX-
22
AIS_RG
21
22
AISRX+
AISRX-
AISTXAIS_TG
EXEVTAISTX+
20
S3
5/R2
NSKT XHD G RX+
20
21
18
19
JAR PA TXNSKT X+
18
19
16
17
ARPAT XJAR PA TX+
16
17
14
15
AL MRXARPAT X+
14
15
PWR ACKEXEVT+
2/S1
3/S2
AL MRX+
13
PWR ACK+
12
13
SYSACK+
SYSACK-
ARPAAC K+
ARPAAC K-
PWR AL M+
PWR AL M-
SYSALM +
SYSALM +
11
10
AL MTX+
AL MTX-
11
12
LOG RX+
LOG RX-
NA V2TX+
NA V2TX-
10
NA V1RX+
NA V1RX-
NA V1TX-
ARPAAL M-
TB4601(ALA RM)
ARPAAL M+
TB4501(OPTION)
NA V1TX+
WH T-WH T
WH T-YE L
BR N
PWR OU T1
PWR IN1
PWR IN1E
12
13
15
16
MTRIN 1MTRIN 1E
10
11
14
PNK
BLK
ORG
WH T-WH T
T B4701(G YRO)
1/R1
GR Y
BL U
GRN
RED
BPIN1
BZIN1E
MTRIN 1+
TRIG IN1
TRIG IN1E
VDIN 1
VDIN 1E
WH T-B LU
GRN
YE L
BLU
T B4201(ISW IN/OU T)
BLK
WHT
RED
CQD-2097 T ERMIN AL BOARD
+48V
+48VG
MTRE
(NC)
MTR+
MTR-
BZ-
BPBZ+
GRN
Y EL
B LU
R ED
WHT
OR N
FILTER AC IN
WMRST-
ACKOU T+
ACKOU TWMRST+
(NC )
(NC )
27
30
EXφZ2
EXφZ2E
25
26
28
29
EXφB2
EXφB2E
23
24
EXφA2
EXφA2E
ETIY2E
SVD 2E
ETIY2
EXφZ1E
SVD 2
EXφB1E
EXφZ1
EXφA1E
EXφB1
EXφA1
ETIY1
ETIY1E
SVD 1
SVD 1E
ETIY3
ETIY3E
RBVD E
21
22
20
18
19
16
17
14
15
12
13
11
10
TB4401(EXT RAD AR)
RBVD
BA TT IN +
BA TT IN -
CBD -1661 ACOU T1
13
14
11
12
10
TRIG BP+
VDTRIG +
TB4101(AN T)
VD+
B LK
WHT
0.6/1kV-D PYCY-6
H-2695110056
TRIG +
TRIG MTR+
MTRMTRE
S TEP- DOWN
T RA NSF OR MER
N BL -175
UT H
TB105
W1
V1
U1
+48V
+48VG
0.6/1kV-D PYCYS-1.5
AC220V , 1φ, fo r HEAT ER
SHIP’S MAINS
P81
PMS
P82
L VR
T XE
PTE
T XI
PTI
P1
NJU-85
PMS
P2
L VR
TXE
TXI
PTI
PTE
PERFORMANCE
MONITOR
B LK
R ED
B LU
B RN
WHT
(X-BAND 25kW RADAR)
B LK
R ED
B LU
B RN
WHT
W iring of PER FOR MANC E MONITOR
is com pleted .
JMA-9122-6XA/9XA レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9122-6XA/9XA
AC100-115V/ AC220-240V 50/60H z 1φ
GRN
YEL
BLU
RE D
TB102
“D” HEATER OPTION
VD+
VD-
BZ+
BZ-
10
11
BP+
BP-
0.6/1kV-DPYC YS-1.5
C IRCU IT BR EAKER
5A ( SHIP YAR D SUPPLY)
SHIP’S MAINS
0.6/1kV-DPYCY S-1. 5
AC100V,1φ,100W
WHT
ORN
T B101
SCANNER UNIT
NKE-1125-61/62/91/92
LOG
250V-T TYCS-4
250V-T TYCS-1
CQD-1891
(J RC SUPPL Y)
J4407
RJ -45 L AN
5-1 P)
19-C OR ES CO MPOSITE CABL E (JRC SU PPL Y)
B.DRAWINGS
AIS
(NMEA0183)
LOG
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
H -2695110006
(J RC SUPPL Y)
3C-2V x 5 (MAX 30m )
250V-T TYCS-1
H -2695111153
(J RC SUPPL Y)
ECHO
SOU NDER
DGPS
CONNING
DISPLAY
ECDIS
VDR
(INTERSWITC H)
RADAR
B.7.5
C DC4 2 3-1
9 0 4J4 BUS(D
DISPLAY UNIT NCD-4990
JMA-9100 Instruction Manual
B.7 Terminal Board Connection Diagram
JMA-9122-6XA/9XA
B －38
Fig B-34: Terminal Board Connection Diagram of JMA-9123-7XA/9XA
250V -M PYCYS-7
0. 6/1kV-D PYCYS-1.5
250V-T TYCS-4
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
0. 6/1kV-D PYCYS-1.5
( NEAREST AP PRO ACH)
ALARM MONITORING
SYSTEM
GYRO
(200P /NM)
LOG
AIS
(NMEA0183)
LOG
ECHO
SOU NDER
DGPS
CONNING
DISPLAY
B LK
BPIN1E
BZIN1
PWR OU T1E
VDOU T1
VDOU T1E
TRIG OU T1
TRIG OU T1E
BPOU T1
BPOU T1E
BZOUT1
BZOUT1E
MTROUT 1+
MTROUT 1MTROUT 1E
17
18
19
20
21
22
23
24
25
26
PUR
WHT
NA V2RX+
NA V2RX-
(N C)
P1+
12
10
11
(NC)
(N C)
(N C)
S2(N C)
(N C)
S1+
P1(N C)
(N C)
(N C)
TB4801(L O G)
MNTTX +
MNTTX -
HD G RX-
22
AIS_RG
21
22
AISRX+
AISRX-
AISTXAIS_TG
EXEVTAISTX+
20
NSKT XHD G RX+
20
21
18
19
S3
5/R2
JAR PA TXNSKT X+
18
19
16
17
2/S1
3/S2
ARPAT XJAR PA TX+
16
17
14
15
AL MRXARPAT X+
14
15
PWR ACKEXEVT+
AL MRX+
13
PWR ACK+
12
13
SYSACK+
SYSACK-
ARPAAC K+
ARPAAC K-
PWR AL M+
PWR AL M-
SYSALM +
SYSALM +
11
10
AL MTX+
AL MTX-
11
12
LOG RX+
LOG RX-
NA V2TX+
NA V2TX-
10
NA V1RX+
NA V1RX-
ARPAAL M-
NA V1TX-
TB4601(ALA RM)
ARPAAL M+
TB4501(OPTION)
NA V1TX+
WH T-WH T
WH T-YE L
R ED
PWR OU T1
PWR IN1
PWR IN1E
12
13
14
MTRIN 1MTRIN 1E
10
11
15
16
BR N
PNK
BLK
ORG
WH T-WH T
T B4701(G YRO)
1/R1
GR Y
BL U
GRN
RED
CQD-1891
(J RC SUPPL Y)
J4407
RJ -45 L AN
BPIN1
BZIN1E
MTRIN 1+
TRIG IN1
TRIG IN1E
VDIN 1
VDIN 1E
WH T-B LU
GRN
YE L
BLU
T B4201(ISW IN/OU T)
BLK
WHT
RED
CQD-2097 T ERMIN AL BOARD
+48V
+48VG
MTRE
(NC)
MTR+
MTR-
BZ-
BPBZ+
GRN
Y EL
B LU
R ED
WHT
OR N
FILTER AC IN
WMRST-
ACKOU T+
27
ACKOU TWMRST+
(NC )
(NC )
25
26
30
EXφZ2
EXφZ2E
23
24
28
29
EXφB2
EXφB2E
EXφA2
EXφA2E
ETIY2E
SVD 2E
ETIY2
EXφZ1E
SVD 2
EXφB1E
EXφZ1
EXφA1E
EXφB1
EXφA1
ETIY1
ETIY1E
SVD 1
SVD 1E
ETIY3
ETIY3E
RBVD E
21
22
20
18
19
16
17
14
15
12
13
11
10
TB4401(EXT RAD AR)
RBVD
BA TT IN +
BA TT IN -
CBD -1661 ACOU T1
13
14
11
12
10
TRIG BP+
VDTRIG +
TB4101(AN T)
VD+
B LK
WHT
0.6/1kV-D PY CY-6
H-2695110056
WHT
OR N
GR N
YEL
Φ ZE
10
MTR E
MTR +
MTR -
BP-/BZBZ+
TR IGBP+
TR IG+
VD +
VD -
TB201
VER R
(NC )
TXI
TXE
PMS
PTE
L VR
TB104
PTI
10
WHT
OR N
GR N
YEL
BLU
R ED
10
PMS
P82
L VR
T XE
PTE
T XI
V0
U0
U1
V1
T B202
+48V G
+48V
ΦB
ΦZ
ΦA
ΦZE
+12V
C2
T B203
GRN
YE L
BLK
P UR
BLU
R ED
GR Y
P1
NJU-85
PMS
P2
L VR
TXE
TXI
PTI
PTE
PERFORMANCE
MONITOR
B LK
R ED
B LU
B RN
WHT
(X-BAND 25kW RADAR)
(N C)
VER R
TXI
TXE
L VR
PMS
PTI
PTE
TB204
10
F R-9 FLEXIBLE WAVEGUIDE
(JRC SUPPLY)
AC 220V, 1φ, for H EATER
B LK
R ED
B LU
B RN
WHT
W iring of PER FOR MANC E MONITOR
is com pleted .
JMA-9123-7XA/9XA レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9123-7XA/9XA
AC100-115V/ AC220-240V 50/60H z 1φ
SHIP’S MAINS
P81
PTI
SHIP’S MAINS
“D” HEATER OPTION
BLK
PUR
R ED
BLU
GRY
TRANSCEIVER UNIT NTG-3225
WHT
ORN
STEP -DOWN
TRA NSFORME R
NBL -175
0.6/1kV-DPYCY S-1.5
CIRCU IT BREAKER
5A ( SHIP YA RD SUPPLY )
ΦB
19-CORES COMPOSIT E CA BLE (JR C SUPPL Y)
10
UT H
TB105
0.6/1kV -DPYCYS-1.5
+12v
C2
V1
W1
ΦZ
ΦA
TB103
U1
SCANNER UNIT
NKE-1129-71/72/91/92
0.6/1kV-D PYCYS-1.5
A C100V,1φ ,100W
H-2695110056
19-C OR ES CO MPOSITE CABL E (JRC SU PPL Y)
H -2695110006
(J RC SUPPL Y)
3C-2V x 5 (MAX 30m )
250V-T TYCS-1
H -2695111153
(J RC SUPPL Y)
B.DRAWINGS
ECDIS
VDR
(INTERSWITC H)
RADAR
5-1 P)
DISPLAY UNIT NCD-4990
B.7.6
C DC4 2 3-1
9 0 4J4 BUS(D
JMA-9100 Instruction Manual
B.7 Terminal Board Connection Diagram
JMA-9123-7XA/9XA
B －39
Fig B-35: Terminal Board Connection Diagram of JMA-9132-SA
250V -M PYCYS-7
0. 6/1kV-D PYCYS-1.5
( NEAREST AP PRO ACH)
ALARM MONITORING
SYSTEM
GYRO
(200P /NM)
0. 6/1kV-D PYCYS-1.5
B LK
VDOU T1E
TRIG OU T1
TRIG OU T1E
BPOU T1
BPOU T1E
BZOUT1
BZOUT1E
MTROUT 1+
MTROUT 1MTROUT 1E
17
18
19
20
21
22
23
24
25
26
R ED
PUR
WHT
NA V2RX+
NA V2RX-
(N C)
P1+
12
10
11
(NC)
(N C)
(N C)
S2(N C)
(N C)
S1+
P1(N C)
(N C)
(N C)
TB4801(L O G)
MNTTX +
MNTTX -
HD G RX-
22
AIS_RG
21
22
AISRX+
AISRX-
AISTXAIS_TG
EXEVTAISTX+
20
S3
5/R2
NSKT XHD G RX+
20
21
18
19
JAR PA TXNSKT X+
18
19
16
17
ARPAT XJAR PA TX+
16
17
14
15
AL MRXARPAT X+
14
15
PWR ACKEXEVT+
2/S1
3/S2
AL MRX+
13
PWR ACK+
12
13
SYSACK+
SYSACK-
ARPAAC K+
ARPAAC K-
PWR AL M+
PWR AL M-
SYSALM +
SYSALM +
11
10
AL MTX+
AL MTX-
11
12
LOG RX+
LOG RX-
NA V2TX+
NA V2TX-
10
NA V1RX+
NA V1RX-
NA V1TX-
ARPAAL M-
TB4601(ALA RM)
ARPAAL M+
TB4501(OPTION)
NA V1TX+
WH T-WH T
WH T-YE L
T B4701(G YRO)
1/R1
GR Y
BL U
GRN
RED
PWR OU T1E
VDOU T1
BR N
PWR OU T1
PWR IN1
PWR IN1E
12
13
15
16
MTRIN 1MTRIN 1E
10
11
14
PNK
BLK
ORG
WH T-WH T
BZIN1E
MTRIN 1+
BPIN1E
BZIN1
BPIN1
TRIG IN1
TRIG IN1E
VDIN 1
VDIN 1E
WH T-B LU
GRN
YE L
BLU
T B4201(ISW IN/OU T)
BLK
WHT
RED
CQD-2097 T ERMIN AL BOARD
+48V
+48VG
MTRE
(NC)
MTR+
MTR-
BZ-
BPBZ+
GRN
Y EL
B LU
R ED
WHT
OR N
FILTER AC IN
WMRST-
ACKOU T+
ACKOU TWMRST+
(NC )
(NC )
27
30
EXφZ2
EXφZ2E
25
26
28
29
EXφB2
EXφB2E
23
24
EXφA2
EXφA2E
ETIY2E
SVD 2E
ETIY2
EXφZ1E
SVD 2
EXφB1E
EXφZ1
EXφA1E
EXφB1
EXφA1
ETIY1
ETIY1E
SVD 1
SVD 1E
ETIY3
ETIY3E
RBVD E
21
22
20
18
19
16
17
14
15
12
13
11
10
TB4401(EXT RAD AR)
RBVD
BA TT IN +
BA TT IN -
CBD -1661 ACOU T1
13
14
11
12
10
TRIG BP+
VDTRIG +
TB4101(AN T)
VD+
B LK
WHT
0.6/1kV-D PYCY-6
H-2695110056
TRIG +
TRIG MTR+
MTRMTRE
S TEP- DOWN
T RA NSF OR MER
N BL -175
UT H
12
W1
U1
V1
+48V
+48VG
10
11
0.6/1kV-D PYCYS-1.5
AC220V , 1φ, fo r HEAT ER
SHIP’S MAINS
P81
PMS
P82
L VR
T XE
PTE
T XI
PTI
P1
NJU-84
PMS
P2
L VR
TXE
TXI
PTI
PTE
PERFORMANCE
MONITOR
B LK
R ED
B LU
B RN
WHT
(S-BAND 30kW RADAR)
B LK
R ED
B LU
B RN
WHT
W iring of PER FOR MANC E MONITOR
is com pleted .
JMA-9132-SA レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9132-SA
AC100-115V/ AC220-240V 50/60H z 1φ
GRN
YEL
BLU
RE D
TB102
“D” HEATER OPTION
VD+
VD-
BZ+
BZ-
10
11
BP+
BP-
0.6/1kV-D PYCYS-1.5
C IRCU IT BR EAKER
5A ( SHIP YAR D SUPPLY)
SHIP’S MAINS
0.6/1kV -DPYCY S-1.5
AC100V,1φ,100W
WHT
ORN
T B101
SCANNER UNIT
NKE-1130-1/2
LOG
250V-T TYCS-4
250V-T TYCS-1
CQD-1891
(J RC SUPPL Y)
J4407
RJ -45 L AN
5-1 P)
19-C OR ES CO MPOSITE CABL E (JRC SU PPL Y)
B.DRAWINGS
AIS
(NMEA0183)
LOG
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
H -2695110006
(J RC SUPPL Y)
3C-2V x 5 (MAX 30m )
250V-T TYCS-1
H -2695111153
(J RC SUPPL Y)
ECHO
SOU NDER
DGPS
CONNING
DISPLAY
ECDIS
VDR
(INTERSWITC H)
RADAR
B.7.7
C DC4 2 3-1
9 0 4J4 BUS(D
DISPLAY UNIT NCD-4990
JMA-9100 Instruction Manual
B.7 Terminal Board Connection Diagram
JMA-9132-SA
B －40
Fig B-36: Terminal Board Connection Diagram of JMA-9133-SA
250V -M PYCYS-7
0. 6/1kV-D PYCYS-1.5
250V-T TYCS-4
250V-T TYCS-1
250V-T TYCS-1
250V-T TYCS-1
0. 6/1kV-D PYCYS-1.5
( NEAREST AP PRO ACH)
ALARM MONITORING
SYSTEM
GYRO
(200P /NM)
LOG
AIS
(NMEA0183)
LOG
ECHO
SOU NDER
DGPS
250V-T TYCS-1
B LK
PWR OU T1E
VDOU T1
VDOU T1E
TRIG OU T1
TRIG OU T1E
BPOU T1
BPOU T1E
BZOUT1
BZOUT1E
MTROUT 1+
MTROUT 1MTROUT 1E
17
18
19
20
21
22
23
24
25
26
PUR
WHT
NA V2RX+
NA V2RX-
(N C)
P1+
12
10
11
(NC)
(N C)
(N C)
S2(N C)
(N C)
S1+
P1(N C)
(N C)
(N C)
TB4801(L O G)
MNTTX +
MNTTX -
HD G RX-
22
AIS_RG
21
22
AISRX+
AISRX-
AISTXAIS_TG
EXEVTAISTX+
20
NSKT XHD G RX+
20
21
18
19
S3
5/R2
JAR PA TXNSKT X+
18
19
16
17
2/S1
3/S2
ARPAT XJAR PA TX+
16
17
14
15
AL MRXARPAT X+
14
15
PWR ACKEXEVT+
AL MRX+
13
PWR ACK+
12
13
SYSACK+
SYSACK-
ARPAAC K+
ARPAAC K-
PWR AL M+
PWR AL M-
SYSALM +
SYSALM +
11
10
AL MTX+
AL MTX-
11
12
LOG RX+
LOG RX-
NA V2TX+
NA V2TX-
10
NA V1RX+
NA V1RX-
ARPAAL M-
NA V1TX-
TB4601(ALA RM)
ARPAAL M+
TB4501(OPTION)
NA V1TX+
WH T-WH T
WH T-YE L
R ED
PWR OU T1
PWR IN1
PWR IN1E
12
13
14
MTRIN 1MTRIN 1E
10
11
15
16
BR N
PNK
T B4701(G YRO)
1/R1
GR Y
BL U
GRN
RED
CQD-1891
(J RC SUPPL Y)
J4407
RJ -45 L AN
BLK
ORG
WH T-WH T
BZIN1E
MTRIN 1+
BPIN1E
BZIN1
BPIN1
TRIG IN1
TRIG IN1E
VDIN 1
VDIN 1E
WH T-B LU
GRN
YE L
BLU
T B4201(ISW IN/OU T)
BLK
WHT
RED
CQD-2097 T ERMIN AL BOARD
+48V
+48VG
MTRE
(NC)
MTR+
MTR-
BZ-
BPBZ+
GRN
Y EL
B LU
R ED
FILTER AC IN
WMRST-
ACKOU T+
27
ACKOU TWMRST+
(NC )
(NC )
25
26
30
EXφZ2
EXφZ2E
23
24
28
29
EXφB2
EXφB2E
EXφA2
EXφA2E
ETIY2E
SVD 2E
ETIY2
EXφZ1E
SVD 2
EXφB1E
EXφZ1
EXφA1E
EXφB1
EXφA1
ETIY1
ETIY1E
SVD 1
SVD 1E
ETIY3
ETIY3E
RBVD E
21
22
20
18
19
16
17
14
15
12
13
11
10
WHT
B LK
0.6/1kV-D PYCY-6
ΦB
12
10
MTR E
MTR +
MTR -
BP-/BZBZ+
TR IGBP+
TR IG+
VD +
VD -
TB201
STEP -DOWN
TRA NSFORME R
NBL -175
0.6/1kV -DPYCYS-1.5
BLK
PU R
11
12
VER R
(NC )
(NC )
(NC )
TXI
TXE
PMS
PTE
L VR
TB104
PTI
10
WHT
OR N
GRN
YE L
BLU
R ED
10
PMS
P82
L VR
T XE
PTE
T XI
W0
V0
W1
U0
U1
V1
T B202
+48V G
+48V
ΦB
ΦZ
ΦA
ΦZE
+12V
C2
GRN
YE L
BLK
PUR
R ED
BLU
GR Y
P1
NJU-84
PMS
P2
L VR
TXE
TXI
PTI
PTE
PERFORMANCE
MONITOR
B LK
R ED
B LU
B RN
WHT
(S-BAND 30kW RADAR)
(N C)
VERR
TXI
TXE
L VR
PMS
PTI
PTE
TB204
10
HF-20D COAXIAL CABLE
(JRC SUPPLY)
AC 220V, 1φ, for H EATER
B LK
R ED
B LU
B RN
WHT
W iring of PER FOR MANC E MONITOR
is com pleted .
JMA-9133-SA レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9133-SA
AC100-115V/ AC220-240V 50/60H z 1φ
SHIP’S MAINS
P81
PTI
SHIP’S MAINS
T B203
0.6/1kV -DPYCYS-1.5
“D” HEATER OPTION
R ED
BLU
GRY
TRANSCEIVER UNIT NTG-3230
WHT
ORN
TB103
CIRCU IT BREAKER
5A ( SHIP YA RD SUPPLY )
ΦA
10
11
19-CORES COMPOSIT E CA BLE (JR C SUPPL Y)
H-2695110056
0.6/1kV-D PYCYS-1.5
A C100V,1φ ,100W
C2
ORN
ΦZE
ΦZ
UTH
+12v
WHT
OR N
WHT
GR N
U1
V1
YE L
SCANNER UNIT
NKE-1139-1/2
TB4401(EXT RAD AR)
RBVD
BA TT IN +
BA TT IN -
CBD -1661 ACOU T1
13
14
11
12
10
TRIG BP+
VDTRIG +
TB4101(AN T)
VD+
H-2695110056
14-C OR ES CO MPOSITE CABL E (JRC SU PPL Y)
250V-T TYCS-1
H -2695110006
(J RC SUPPL Y)
3C-2V x 5 (MAX 30m )
250V-T TYCS-1
H -2695111153
(J RC SUPPL Y)
B.DRAWINGS
CONNING
DISPLAY
ECDIS
VDR
(INTERSWITC H)
RADAR
5-1 P)
DISPLAY UNIT NCD-4990
B.7.8
C DC4 2 3-1
9 0 4J4 BUS(D
JMA-9100 Instruction Manual
B.7 Terminal Board Connection Diagram
JMA-9133-SA
JMA-9100 Instruction Manual
B.7.9
B.DRAWINGS
B.7 Terminal Board Connection Diagram
NCD-4990T
DISPLAY UNIT NCD-4990T
MONITOR UNIT
NWZ-170
OPERATION UNIT
NCE-5163
J4406
DVI-D
DSUB -9P
FEMALE
J4309
RADAR PROCESS
CIRCUIT
CDC-1324
TERMINAL BOARD
CQD-2097
Option
Option for X-band 10kW and X-band 25kW-H S.
Used with N KE-2103-6,N KE-2103-6H S and N KE-
CBD -1661
AC OUT 2
2254-6H S
AC/DC
CONVERTER UNIT
POWER SUPPLY
CBD-1661
TB 402
ー
FG
FG
J4311
J4312
CBD -1684A TB522
Main
Sub
NBA-5135
CBD -1684A TB521
SUB OPERATION UNIT
NCE-5163
ー
FG
CBD -1661
AC OUT 1
RADAR PROCESS UNIT
NDC-1399-9
JMA-9100 Series RADAR
NCD-4990T 卓上型レーダー指示機 ユニット間接続図
INTERCONNECTION DIAGRAM OF DISPLAY UNIT TYPE NCD-4990 T(desktop)
Fig B-37: Inter-Unit Connection Diagram of NCD-4990T
B －41
JMA-9100 Instruction Manual
B.8
B.DRAWINGS
B.8 GYRO I/F
GYRO I/F
SERIAL SIGNAL
INDICATOR LED
シリアル信号表示LED
KEEP DEFAULT
設定不要
OPEN
プラグ無し
GYRO INPUT SIGNAL
INDICATOR LED
ジャイロ入力信号LED
GYRO LOW-VOLTAGE
ALERT LED
ジャイロ低電圧警告LED
ERROR INDICATOR LED
エラー表示LED
GYRO SIGNAL PROCESS
INDICATOR LED
ジャイロ信号処理表示LED
LOG PULSE
INDICATOR LED
ログパルス表示LED
LOW-VOLTAGE GYRO
SETTING
ジャイロ低電圧時に設定
Fig B-38: Parts Location of CMJ-462E
TableB-1： Setting Table of CMJ-462E S1/S2
S1 SETTING
OFF
ON
ON
90X
OFF
ON
180X
ON
OFF
360X
OFF
OFF
GYRO SIMULATOR
LOG SIMULATOR
逆／REV
ON
正／NOR
OFF
ON
パルス／PULSE
OFF
GYRO ALM TIME
GYRO SRC
(Heading Sensor Source)
OFF
未接続／NC
100P／30X
ON
ON
200P／90X
OFF
ON
400P／180X
ON
OFF
800P／360X
OFF
OFF
NMEA BAUDRATE
B －42
4800 BPS
OFF
OFF
9600 BPS
ON
OFF
19200 BPS
OFF
ON
38400 BPS
ON
ON
ON
OFF
ON
OFF
ON
OFF
N.C. (No Connection)
シンクロ／SYNC
パルス
PULSE/NM
S2 SETTING
BSHLOG ALM
36X
回転方向
DIRECTION
ログ信号
LOG SETTING
ON
SYNC
RATIO
ジャイロ信号
GYRO SETTING
STEP
OFF
5 SEC
ON
0.2 SEC
OFF
HDT ( NMEA (HDT/THS) )
ON
GYRO
OFF
JMA-9100 Instruction Manual
B.DRAWINGS
B.8 GYRO I/F
TableB-2： Gyro, Log Settings
B －43
JMA-9100 Instruction Manual
B.9
B.9.1
B.DRAWINGS
B.9 Inter Switch Unit
Inter Switch Unit
Terminal Board Connection Diagram
DISPLAY 1
DISPLAY 2
NCD-4990
NCD-4990
TB4201
ISW IN/OUT
TB4201
ISW IN/OUT
VDIN 1
VDIN 1E
TRIGIN 1
TRIGIN 1E
BPIN 1
BPIN 1E
BZIN 1
BZIN 1E
MTRIN 1+
MTRIN 1-
10
MTRIN 1E
11
PWRIN 1+
12
PWRIN 1E
13
PWROUT 1
14
PWROUT 1E
15
VDOUT 1
16
VDOUT 1E
17
TRIGOUT 1
18
TRIGOUT 1E
19
BPOUT 1
20
BPOUT 1E
21
BZOUT 1
22
BZOUT 1E
23
MTROUT 1+
24
MTROUT 1-
25
MTORUT 1E
26
BLUE
YELLOW
GREEN
WHITE-BLUE
WHITE-WHITE
ORANGE
BLACK
PINK
BROWN
RED
PURPLE
CLEAR
WHITE-YELLOW
WHITE-WHITE
VDIN 1
VDIN 1E
TRIGIN 1
TRIGIN 1E
BPIN 1
BPIN 1E
BZIN 1
BZIN 1E
MTRIN 1+
10
MTRIN 1-
11
MTRIN 1E
12
PWRIN 1+
13
PWRIN 1E
14
PWROUT 1
15
PWROUT 1E
16
VDOUT 1
17
VDOUT 1E
18
TRIGOUT 1
19
TRIGOUT 1E
20
BPOUT 1
21
BPOUT 1E
22
BZOUT 1
23
BZOUT 1E
24
MTROUT 1+
25
MTROUT 1-
26
MTORUT 1E
H-2695111153
(JRC SUPPLY )
Fig B-39: Terminal Board Connetion Diagram of NQE-3141-2A
B －44
B －45
Fig B-40: Terminal Board Connection Diagram of NQE-3141-4A
H-2695111153
BR N
PN K
BL K
15
14
13
12
11
VDOUT 1
VDOUT 1E
TRIGOUT 1
TRIGOUT 1E
16
17
18
19
20
MTROUT 1MTORUT 1E
25
26
WH T-WHT
WHT -YEL
CL R
PUR
RED
M TROUT 1+
24
11
10
TB912
BZOUT 1
BZOUT 1E
22
23
21
H-2695111153
ORG
PWROUT 1E
15
BR N
PN K
OR
BLK
WH T-WH T
WH T-BLU
G RN
YEL
BLU
WHT-YEL
WHT-WHT
CLR
PUR
RED
BRN
BLK
PNK
15
14
13
12
11
10
TB913
CH-2
PWRIN 1+
PWRIN 1E
PWROUT 1
PWROUT 1E
VDOUT 1
VDOUT 1E
TRIGOUT 1
TRIGOUT 1E
12
13
14
15
16
17
18
19
20
WH T-WHT
WHT-Y EL
WH T
PUR
RED
MTROUT 1MTORUT 1E
25
26
11
10
TB914
MTROUT 1+
24
NKE-3141-4
CCL-304R
BZOUT 1
BZOUT 1E
22
23
BPOUT 1
BPOUT 1E
M TRIN 1MTRIN 1E
21
MTRIN 1+
10
11
H-2695111153
10
PWRIN 1E
PWROUT 1
13
14
BR N
PN K
BLK
O RG
WH T-WH T
WH T-BLU
GR N
YEL
BLU
WHT-YEL
WHT-WHT
CLR
PUR
RED
BRN
BLK
PNK
ORG
WHT-BLU
WHT-WHT
GRN
YEL
BLU
15
14
13
12
11
10
TB915
CH-3
BPIN 1E
BZIN 1
BZIN 1E
PWRIN 1+
PW RIN 1E
PWROUT 1
PWROUT 1E
VDOUT 1
VDOUT 1E
TRIGOUT 1
TRIGOUT 1E
12
13
14
15
16
17
18
19
20
MTROUT 1MTORUT 1E
25
26
WH T-WHT
W HT-YEL
WHT
PUR
RED
MTROUT 1+
24
11
10
TB916
BZOUT 1
BZOUT 1E
22
23
BPOUT 1
BPOUT 1E
MTRIN 1MTRIN 1E
21
MTRIN 1+
10
11
TRIGIN 1
TRIGIN 1E
BPIN 1
VDIN 1
VDIN 1E
H-2695111153
WH T-WHT
WH T-BL U
G RN
PWRIN 1+
12
ORG
W HT-BLU
WHT-WHT
BPIN 1E
BZIN 1
BZIN 1E
TRIGIN 1
TRIGIN 1E
BPIN 1
VDIN 1
VDIN 1E
BRN
PN K
BLK
OR G
WH T-WH T
WH T-BLU
GR N
YEL
B LU
WHT-YEL
WHT-WHT
CLR
PUR
RED
BRN
BLK
PNK
ORG
WHT-BLU
WHT-WHT
GRN
YEL
BLU
15
14
13
12
11
10
TB915
CH-4
BPIN 1E
BZIN 1
BZIN 1E
PWRIN 1+
PWRIN 1E
PWROUT 1
PWROUT 1E
VDOUT 1
VDOUT 1E
TRIGOUT 1
TRIGOUT 1E
12
13
14
15
16
17
18
19
20
MTROUT 1MTORUT 1E
25
26
WH T-WHT
WHT-Y EL
WHT
PUR
RED
11
10
TB916
MTROUT 1+
24
BZOUT 1
BZOUT 1E
22
23
BPOUT 1
BPOUT 1E
MTRIN 1M TRIN 1E
21
MTRIN 1+
10
11
TRIGIN 1
TRIGIN 1E
BPIN 1
VDIN 1
VDIN 1E
DISPLAY4
NCD-4990
TB4201
CH-1
M TRIN 1MTRIN 1E
10
11
GRN
YEL
BLU
DISPLAY3
NCD-4990
TB4201
B.DRAWINGS
YEL
BLU
TB911
MTRIN 1+
BPOUT 1
BPOUT 1E
BPIN 1E
BZIN 1
BZIN 1E
TRIGIN 1
TRIGIN 1E
BPIN 1
VDIN 1
VDIN 1E
DISPLAY2
NCD-4990
TB4201
WHT-WHT
WHT-YEL
CLR
PUR
RED
BRN
BLK
PNK
ORG
WHT-WHT
WHT-BLU
GRN
YEL
BLU
DISPLAY1
NCD-4990
TB4201
JMA-9100 Instruction Manual
B.9 Inter Switch Unit
(JRC SUPPLY )
(JRC SUPPLY )
(JRC SUPPLY )
(JRC SUPPLY )
H-7ZCRD0971
J1
VIN
VIN
CBD-1675
5V
GND
+15V
GND
GND
H-7ZCRD0972
P903
5V
GND
+15V
GND
GND
J3
J3
CQD-1973
CH-2
CH-3
CH-4
CQD-1973
CH-1
CCL-304
B.DRAWINGS
ＴＢ914
ＴＢ913
ＴＢ911
B －46
26
H-7ZCRD0970A
26
ＴＢ912
26
H-7ZCRD0970A
26
Fig B-41: Interconnection Diagram of NQE-3141-2A
Terminal board Terminal board
J4306
J4307
(ISW-1CH)
(ISW-1CH)
J903
-15V
Terminal board
J4308 ISW
-15V
P902
B.9.2
J2
JMA-9100 Instruction Manual
B.9 Inter Switch Unit
Interconnection Diagram
ＴＢ918
ＴＢ917
ＴＢ916
ＴＢ915
TB901
LF901
AC100V-240V
C901
C902
TE901
C903
LINE
FG
CB901
LOAD
CD9
01
H-7ZCRD0919
B901
P901
FG
AC(N)
AC(L)
CN1
CBA-357
B －47
H-7ZCRD0920
J903
J909
FANP LS
FANE
FANV
J905
PO WLED
TRT
P-
TRT
P+
AC
(N)
AC
(L)
J904
5V
GND
+15V
GND
GND
-15V
6.B POUTE
7.B ZOU T
6.B PIN E
7.B ZIN
Fig B-42: Interconnection Diagram of NQE-3141-4A
TO
DISPLAY1
NCD-4990
TB4201
14.PWR OU T
15.PWR OU T
13.RWR INE
12.PWR IN
11.MTR INE
10.MTR IN-
9.MTR OU T+
10 .MTROU T
-11 .MTROU T
5.B POUT
5.B PIN
8.B ZOU TE
4.TR GOU TE
4.T RG INE
9.MT RIN +
3.TR GOU T
3.T RG IN
8.B ZIN E
2.V DOUTE
TB 912
1.V DOUT
2.V DI NE
TB 911
1.V DI N
CH-1
TB 914
TO
DISPLAY2
NCD-4990
TB4201
TB 913
CH -2
TB 916
TO
DISPLAY3
NCD-4990
TB4201
TB 915
CH-3
CCL-304
TB 917
TB 918
CH-4
B.DRAWINGS
P909
P905
10
P904
P903
R901
P902
H -7ZCRD 0921
5V
GND
+15V
GND
GND
-15V
CN2
JMA-9100 Instruction Manual
B.9 Inter Switch Unit
JMA-9100 Instruction Manual
B.DRAWINGS
B.9 Inter Switch Unit
B －48
Appendix C
Menu Index
Menu Index
C.1
Main ....................................................................................................... C-1
C.2
PI ............................................................................................................ C-5
C.3
TT ........................................................................................................... C-7
C.4
AIS ......................................................................................................... C-8
C.5
AZ .......................................................................................................... C-9
C.6
Track .................................................................................................... C-10
C.7
Route ................................................................................................... C-11
C.8
U.Map .................................................................................................. C-12
C.9
Serviceman Menu ............................................................................... C-14
JMA-9100 Instruction Manual
C.1
C.Menu Index
C.1 Main
Main
├
│
│
│
│
├
├
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
1. EBL Maneuver Setting - - - - - - - - - - - - - - - - ├ 1. EBL Maneuver
├ 2. Reach
├ 3. Turn Mode
└ 4. Turn Set
2. File Manager - - - - - - - - - - - - - - - - - - - - 3. RADAR Menu
├ 1. Process Setting - - - - - - - - - - - - - - - │
├ 1. Video Latitude - - - - - - - - - - - - │
├ 2. Video Noise Rejection - - - - - - - - │
├ 3. AUTO Dynamic Range - - - - - - - │
├ 4. Process Switch - - - - - - - - - - - │
├ 5. 2nd Process Mode- - - - - - - - - - │
├ 6. Process Switch Rrange - - - - - - - │
├ 7. Fast Target Detection - - - - - - - - │
├ 8. User Function Setting - - - - - - - - │
│
├ 1. Function1 Setting
│
│
│
├ 1. Mode - - - - - - - - │
│
│
├ 2. IR
│
│
│
├ 3. Process
│
│
│
├ 4. Target Enhance
│
│
│
├ 5. AUTO Sea/Rain
│
│
│
├ 6. Save Present State
│
│
│
├ 9. Next
│
│
│
├ 1. Pulse Length 0.75nm │
│
│
├ 2. Pulse Length 1.5nm
│
│
│
├ 3. Pulse Length 3/4nm
│
│
│
├ 4. Pulse Length 6/8nm
│
│
│
├ 5. Pulse Length 12nm
│
│
│
├ 6. Pulse Length 16nm
│
│
│
├ 9. Next
│
│
│
├ 1. Video Latitude - - - - │
│
│
├ 2. Video Noise Rejection
│
│
│
├ 3. AUTO Dynamic Range
│
│
│
├ 4. Process Switch
│
│
│
├ 5. 2nd Process Mode
│
│
│
├ 6. Process Switch Range
│
│
│
├ 7. Fast Target Detection
│
│
│
├ 9. Next
│
│
│
├ 1. Trails Interval - - - - │
│
│
├ 2. Trails Mode
│
│
│
├ 3. Trails Reference Level
│
│
│
├ 4. Trails Reduction
│
│
│
├ 6. Trails Process
│
│
│
├ 7. Max Interval
│
│
│
├ 9. Next
│
│
│
├ 1. Gain Offset - - - - - │
│
│
├ 2. PRF
│
│
│
├ 3. Small Buoy Detection
│
│
│
├ 4. Fishnet Detection
│
│
│
├ 5. Antenna Height
│
│
│
├ 8. Set Mode Default
│
│
│
└ 9. Initialize
│
│
├ 2. Function2 Setting
│
│
├ 3. Function3 Setting
│
│
└ 4. Function4 Setting
│
└ 9. SART - - - - - - - - - - - - - - - - ├ 2. RADAR Trails Setting
│
├ 1. Trails Mode - - - - - - - - - - - - - │
├ 2. Trails Ref Level - - - - - - - - - - - │
├ 3. Trails Reduction - - - - - - - - - - - │
├ 5. Trails Process - - - - - - - - - - - - -
C －1
- - - - - - - - section 4.1.5 on page 4-14
- - - - - - - section 3.11.1 on page 3-120
- section 3.8.1 on page 3-91
section 3.8.1.1 on page 3-91
section 3.8.1.2 on page 3-92
section 3.8.1.3 on page 3-92
section 3.8.1.4 on page 3-93
section 3.8.1.5 on page 3-93
section 3.8.1.6 on page 3-93
section 3.8.1.7 on page 3-94
- section 3.9.3 on page 3-113
- - - - - - - - - - - - - - - page 3-113
- - - - - - - - - - - - - - - page 3-115
- - - - - - - - - - - - - - - page 3-115
- - - - - - - - - - - - - - - page 3-115
- - - - - - - - - - - - - - - page 3-115
- - - - - - - - - section 6.5 on page 6-12
section
section
section
section
3.8.2.1
3.8.2.2
3.8.2.3
3.8.2.4
on
on
on
on
page
page
page
page
3-95
3-95
3-96
3-96
JMA-9100 Instruction Manual
│
│
│
│
│
│
├
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
├
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
├
│
│
│
│
│
│
│
│
├
│
│
│
│
│
│
│
│
│
│
│
4.
5.
6.
7.
C.Menu Index
C.1 Main
│
└ 6. Max Interval - - - - - - - └ 3. TXRX Setting
│
├ 1. PRF Fine Tuning - - - - │
├ 2. Stagger Trigger - - - - - │
├ 4. PRF - - - - - - - - - - - │
└ 5. Ice Class Standby Mode - Multi Window Setting
├ 1. DIR/DIST EXP Display- - - - - - ├ 2. Numeric NAV INFO - - - - - - - ├ 3. Depth Graph Setting - - - - - - - │
├ 1. Depth Graph Display
│
├ 2. Depth Range
│
├ 3. Time Range
│
└ 4. Depth Unit
├ 4. Wind Graph Setting - - - - - - - │
├ 1. Wind Graph Display
│
└ 2. Wind Speed Unit
├ 5. TEMP Graph Setting- - - - - - - │
├ 1. TEMP Graph Display
│
├ 2. TEMP Graph Color
│
├ 3. TEMP Range
│
│
├ 1. Temperature setting
│
│
├ 2. Temperature setting
│
│
├ 3. Temperature setting
│
│
├ 4. Temperature setting
│
│
├ 5. Temperature setting
│
│
└ 6. Temperature setting
│
└ 4. Time Range
└ 6. Course Bar Setting - - - - - - - │
├ 1. Course Bar Display
│
├ 2. Autopilot Course
│
└ 3. ROT Scale
Map Setting
├ 3. JRC/ERC Setting
│
├ 1. Day/Night
│
├ 2. Color of Land
│
├ 3. Bright of Land
│
├ 4. Color of Sea
│
├ 5. Bright of Sea
│
├ 6. Color of Name
│
├ 7. Bright of Name
│
├ 8. Bright of Track/Mark/Line
│
├ 9. Next
│
├ 1. LAT/LON Line
│
├ 2. Color of L/L Line
│
└ 3. Bright of L/L Line
├ 5. Map Display Setting
│
└ 3. LAT/LON Correction
└ 7. Map Draw AZI Mode
NAV Equipment Setting
├ 1. GYRO Setting - - - - - - - - - - ├ 2. MAG Compass Setting - - - - - │
├ 1. Heading Correction
│
└ 2. Correct Value
└ 3. Set/Drift Setting - - - - - - - - - │
├ 1. Correction
│
├ 2. Set
│
└ 3. Drift
Sub Menu
├ 1. Display Color Setting - - - - - - │
├ 1. Day/Night - - - - - - - - │
├ 2. Outer PPI
│
├ 3. Inner PPI
│
├ 4. Character
│
├ 5. RADAR Video
│
├ 6. RADAR Trails(Time)
│
├ 8. Target Symbol
│
├ 9. Next
│
├ 1. Cursor
│
├ 2. Range Rings
C －2
- - - - - - - - - - - - - section 3.8.2.5 on page 3-96
section
section
section
section
3.8.3.1
3.8.3.2
3.8.3.3
3.8.3.4
on
on
on
on
page
page
page
page
3-97
3-97
3-97
3-98
- - - - - - - - - - - - - section 3.8.8.1 on page 3-105
- - - - - - - - - - - - - section 3.8.8.2 on page 3-105
- - - - - - - - - - - - - section 3.8.8.3 on page 3-106
- - - - - - - - - - - - - section 3.8.8.4 on page 3-107
- - - - - - - - - - - - - section 3.8.8.5 on page 3-108
(MIN)
(MAX)
- - - - - - - - - - - - - section 3.8.8.6 on page 3-109
- - section 3.4.14 on page 3-36, section 7.1.7 on page 7-9
- - - - - - - - - - - - - - section 3.4.16 on page 3-37
- - - - - - - - - - - - - section 3.4.16.1 on page 3-38
- - - - - - - - - - - - - section 3.8.5.1 on page 3-99
- - - - - - - - - - - - - section 3.8.5.2 on page 3-100
JMA-9100 Instruction Manual
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
├
│
├
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
├ 3. EBL/VRM/PI
│
└ 4. Own Symbol/HL/Vector
├ 2. Brilliance Setting- - - - - - - - │
├ 1. RADAR Video - - - - - │
├ 2. RADAR Trails
│
├ 3. Target Symbol - - - - - │
├ 4. Range Rings
│
├ 5. EBL/VRM/PI
│
├ 6. Character
│
├ 7. Own Symbol/HL/Vector
│
└ 8. Keyboard
├ 3. User Setting
│
├ 1. Load User Setting - - - │
├ 2. Save User Setting - - - │
└ 3. Delete User Setting - - ├ 4. Option Key Setting
│
├ 1. Option1 - - - - - - - - │
└ 2. Option2 - - - - - - - - ├ 5. Buzzer Volume - - - - - - - - │
├ 1. Key ACK
│
├ 2. OPE Miss
│
├ 3. CPA/TCPA Alarm
│
├ 4. New Target Alarm
│
├ 5. Lost Alarm
│
├ 6. Navigation Alarm
│
├ 7. System Alarm
│
└ 8. Inter Switch
├ 6. Date/Time Setting - - - - - - - │
├ 1. UTC/LMT
│
├ 2. LMT Date
│
├ 3. LMT Time
│
├ 4. Time Zone
│
├ 5. Display Style
│
└ 6. Synchronize with GPS
├ 7. Screen Capture Setting
│
├ 1. Select Item
│
│
├ 1. Graphic
│
│
├ 2. RADAR Video
│
│
├ 3. RADAR Trails
│
│
└ 4. Map
│
├ 2. Select Card Slot
│
├ 3. File Erase
│
├ 4. AUTO Capture Interval
│
└ 5. AUTO File Erase
├ 9. EBL/Cursor Setting - - - - - - │
├ 1. EBL1 Bearing Fix
│
├ 2. EBL2 Bearing Fix
│
└ 3. Cursor Setting - - - - - │
│
├ 1. EBL/VRM Control
│
│
├ 2. Cursor Length
│
│
└ 4. Cursor Pattern
8. Plot Setting
└ 6. AUTO Backup - - - - - - - - - 9. Test Menu- - - - - - - - - - - - - - - ├ 1. Self Test - - - - - - - - - - - │
├ 1. Memory Test
│
│
├ 1. SDRAM
│
│
├ 2. SRAM
│
│
├ 3. FLASH ROM
│
│
└ 4. GRAPHIC
│
├ 2. TXRX Test
│
├ 3. Line Test
│
└ 4. Supply Voltage
├ 2. Monitor Test - - - - - - - - - - │
├ 1. Pattern 1
│
├ 2. Pattern 2
│
├ 3. Pattern 3
│
├ 4. Pattern 4
│
├ 5. Pattern 5
│
├ 6. Pattern 6
C.Menu Index
C.1 Main
- - - - - - - - - - - - - - section 3.8.5.3 on page 3-100
- - - - - - - - - - - - - - section 3.8.5.4 on page 3-101
- - - - - - - - - - - - - - section 3.8.5.5 on page 3-102
- - - - - - - - - - - - - - section 3.10.1 on page 3-118
- - - - - - - - - - - - - - section 3.10.2 on page 3-119
- - - - - - - - - - - - - - section 3.10.3 on page 3-119
- - - - - - - - - - - - - - - section 3.8.7 on page 3-103
- - - - - - - - - - - - - - - section 3.8.7 on page 3-103
- - - - - - - - - - - - - - - section 3.8.6 on page 3-102
- - - - - - - - - - - - - - - section 7.2.7 on page 7-20
- - - - - - - - - - - - - - - - section 4.1.3 on page 4-3
- - - - - - - - - - - - - - - section 4.1.3.3 on page 4-5
CURS
- - - - - - - - - - - - - - - section 3.8.9 on page 3-110
- - - - - - - - - - - - - - - - section 8.3.1 on page 8-6
- - - - - - - - - - - - - - - section 8.3.1.1 on page 8-7
- - - - - - - - - - - - - - - section 8.3.1.2 on page 8-9
C －3
JMA-9100 Instruction Manual
│
│
│
│
│
│
│
│
│
└
C.Menu Index
│
│
├ 3.
│
│
│
├ 4.
├ 5.
└ 6.
0. EXIT
C.1 Main
├ 7. Pattern 7
└ 8. Pattern 8
Keyboard Test- - ├ 1. Key Test
├ 2. Buzzer Test
└ 3. Light Test
MON Display - - System Alarm Log System Information
- - - - - - - - - - - - - - - - - - - - - - section 8.3.1.3 on page 8-9
- - - - - - - - - - - - - - - - - - - - - section 8.3.1.4 on page 8-10
- - - - - - - - - - - - - - - - - - - - - section 8.3.1.5 on page 8-10
- - - - - - - - - - - - - - - - - - - - - section 8.3.1.6 on page 8-11
C －4
JMA-9100 Instruction Manual
C.2
C.Menu Index
C.2 PI
PI
├
├
│
│
│
│
├
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
├
├
├
├
├
├
├
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
├
├
1. Display for All Lines - - - - - - - - 2. Operation Mode - - - - - - - - - - ├ All
├ Individual
├ Track
└ Equiangular
3. Control1 - - - - - - - - - - - - - - - - - ├ All:All2
├ Individual:Sequential
├ Individual:Index Line 1
├ Individual:Index Line 2
├ Individual:Index Line 3
├ Individual:Index Line 4
├ Individual:Index Line 5
├ Individual:Index Line 6
├ Individual:Index Line 7
├ Individual:Index Line 8
├ Track:Group 1
├ Track:Group 2
├ Track:Group 3
├ Track:Group 4
├ Equiangular:Group 1
├ Equiangular:Group 2
├ Equiangular:Group 3
└ Equiangular:Group 4
4. Floating - - - - - - - - - - - - - - 5. Heading Link - - - - - - - - - - - 6. Next
8. Press EBL Dial to Control PI#3
9. Press VRM Dial to Move End Point#ii
1. Range Scale Link - - - - - - - - - 2. Reference Bearingi- - - - - - - - - - - ├ All:True4
├ All:HL
├ Individual:True
├ Individual:HL
├ Individual:Index Line 1
├ Individual:Index Line 2
├ Individual:Index Line 3
├ Individual:Index Line 4
├ Individual:Index Line 5
├ Individual:Index Line 6
├ Individual:Index Line 7
├ Individual:Index Line 8
├ Track:True
├ Track:HL
├ Track:Index Line 1
├ Track:Index Line 2
├ Track:Index Line 3
├ Track:Index Line 4
├ Track:Index Line 5
├ Track:Index Line 6
├ Track:Index Line 7
└ Track:Index Line 8
3. Operation Area - - - - - - - - - - 4. Display for Individual Line - - - - - -
- - - - - - - - - - - - - - - - - section 4.1.4.3 on page 4-9
- - - - - - - - - - - - - - - - - - - - - - - - page 4-10
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-11
- - - - - - - - - - - - - - - - - - - - - - - - - page 4-11
- - - - - - - - - - - - - - - - - - - - - - - - -page 4-11
- - - - - - - - - - - - - - - - - - - - - - - - page 4-12
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-12
- - - - - - - - - - - - - - - - - - - - - - - - page 4-13
- - - - - - - - - - - - - - - - - - - - - - - - page 4-13
1.The setting items are determined by the setting of Operation Mode.
2.Operating Mode : Control
3.Displayed only when "3. Control" is Individual.
4.Operating Mode : Reference Bearing
C －5
JMA-9100 Instruction Manual
│
│
│
│
│
│
│
│
├
└
C.Menu Index
C.2 PI
├ 1. Index Line 1
├ 2. Index Line 2
├ 3. Index Line 3
├ 4. Index Line 4
├ 5. Index Line 5
├ 6. Index Line 6
├ 7. Index Line 7
└ 8. Index Line 8
8. Press EBL Dial to Control PI#ii
9. Press VRM Dial to Move End Point#ii
C －6
JMA-9100 Instruction Manual
C.3
C.Menu Index
C.3 TT
TT
├
│
│
│
│
│
│
│
├
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
├
│
│
│
│
│
│
│
│
│
│
├
└
│
│
│
│
1. Association Setting - - - - - - - ├ 1. Association
├ 2. Proprity
├ 3. Bearing
├ 4. Range
├ 5. Course
├ 6. Speed
└ 7. Applicable AIS Target
2. Target Track Setting - - - - - - - ├ 1. Target Track Function - - ├ 2. Target Track Color- - - - │
├ 1. All
│
├ 2. Target Track No.1
│
├ 3. Target Track No.2
│
├ 4. Target Track No.3
│
├ 5. Target Track No.4
│
├ 6. Target Track No.5
│
├ 7. Target Track No.6
│
├ 8. Target Track No.7
│
├ 9. Next
│
├ 1. Target Track No.8
│
├ 2. Target Track No.9
│
├ 3. Target Track No.10
│
└ 4. Other
├ 3. Target Track Display- - - │
├ 1. All
│
├ 2. Target Track No.1
│
├ 3. Target Track No.2
│
├ 4. Target Track No.3
│
├ 5. Target Track No.4
│
├ 6. Target Track No.5
│
├ 7. Target Track No.6
│
├ 8. Target Track No.7
│
├ 9. Next
│
├ 1. Target Track No.8
│
├ 2. Target Track No.9
│
├ 3. Target Track No.10
│
└ 4. Other
├ 4. Track Memory Interval - - ├ 5. Clear Track Color - - - - ├ 6. Clear Track Number
└ 7. File Operations - - - - - │
├ 1. Select Card Slot
│
├ 2. Load Mode
│
├ 3. Load - - - - - - │
├ 4. Save - - - - - - │
├ 5. Erase - - - - - - │
└ 6. Card T.TRK Display
3. Trial Maneuver - - - - - - - - - ├ 1. Trial Function
├ 2. Course(EBL)
├ 3. Speed(VRM)
├ 4. Vector Time
├ 5. Time to Maneuver
└ 6. Own Ship's Dynamic Trait
│
├ 1. Reach
│
├ 3. Turn Radius
│
├ 4. Acceleration
│
└ 5. Deceleration
4. Target Number Display - - - - - 9. TT Test Menu - - - - - - - - - - ├
├
├
└
1.
2.
3.
4.
Test Video- TT Simulator
Status - - - Gate Display
- - - - - - - - - - - - - - - - - - - section 5.4 on page 5-37
- - - - - - - - - - - - - - - - - - section 5.6.2 on page 5-44
- - - - - - - - - - - - - - - - - section 5.6.2.2 on page 5-44
- - - - - - - - - - - - - - - - - section 5.6.2.1 on page 5-44
- - - - - - - - - - - - - - - - - section 5.6.2.4 on page 5-46
- - - - - - - - - - - - - - - - - section 5.6.2.5 on page 5-47
- - - - - - - - - - - - - - - - - section 5.6.2.6 on page 5-47
- - - - - - - - - - - - - - - - - section 5.6.2.7 on page 5-48
page 5-48
page 5-49
page 5-51
page 5-52
section 5.7 on page 5-53
- - - - - - - - - - - - - - - - - - section 5.2.4 on page 5-18
- - - - - - - - - - - - - - - - - - section 5.2.7 on page 5-21
C －7
section
section
section
section
5.2.7.1
5.2.7.2
5.2.7.3
5.2.7.4
on
on
on
on
page
page
page
page
5-22
5-23
5-24
5-25
JMA-9100 Instruction Manual
C.4
C.Menu Index
C.4 AIS
AIS
├
│
│
│
│
│
│
│
├
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
├
│
│
│
│
│
│
│
│
│
│
├
│
│
1. Association Setting - - - - - - - ├ 1. Association
├ 2. Proprity
├ 3. Bearing
├ 4. Range
├ 5. Course
├ 6. Speed
└ 7. Applicable AIS Target
2. Target Track Setting - - - - - - - ├ 1. Target Track Function - - ├ 2. Target Track Color- - - - │
├ 1. All
│
├ 2. Target Track No.1
│
├ 3. Target Track No.2
│
├ 4. Target Track No.3
│
├ 5. Target Track No.4
│
├ 6. Target Track No.5
│
├ 7. Target Track No.6
│
├ 8. Target Track No.7
│
├ 9. Next
│
├ 1. Target Track No.8
│
├ 2. Target Track No.9
│
├ 3. Target Track No.10
│
└ 4. Other
├ 3. Target Track Display- - - │
├ 1. All
│
├ 2. Target Track No.1
│
├ 3. Target Track No.2
│
├ 4. Target Track No.3
│
├ 5. Target Track No.4
│
├ 6. Target Track No.5
│
├ 7. Target Track No.6
│
├ 8. Target Track No.7
│
├ 9. Next
│
├ 1. Target Track No.8
│
├ 2. Target Track No.9
│
├ 3. Target Track No.10
│
└ 4. Other
├ 4. Track Memory Interval - - ├ 5. Clear Track Color - - - - ├ 6. Clear Track Number
└ 7. File Operations - - - - - │
├ 1. Select Card Slot
│
├ 2. Load Mode
│
├ 3. Load - - - - - - │
├ 4. Save - - - - - - │
├ 5. Erase - - - - - - │
└ 6. Card T.TRK Display
3. Trial Maneuver - - - - - - - - - ├ 1. Trial Function
├ 2. Course(EBL)
├ 3. Speed(VRM)
├ 4. Vector Time
├ 5. Time to Maneuver
└ 6. Own Ship's Dynamic Trait
│
├ 1. Reach
│
├ 2. Turn Radius
│
├ 3. Acceleration
│
└ 4. Deceleration
4. AIS Filter Setting - - - - - - - - ├ 1. Filter Type - - - - - - - - ├ 2. Make AIS Filter - - - - - -
- - - - - - - - - - - - - - - - - - section 5.4.2 on page 5-37
- - - - - - - - - - - - - - - - - - section 5.6.2 on page 5-44
- - - - - - - - - - - - - - - - - section 5.6.2.2 on page 5-44
- - - - - - - - - - - - - - - - - section 5.6.2.1 on page 5-44
- - - - - - - - - - - - - - - - - section 5.6.2.4 on page 5-46
- - - - - - - - - - - - - - - - - section 5.6.2.5 on page 5-47
- - - - - - - - - - - - - - - - - section 5.6.2.6 on page 5-47
- - - - - - - - - - - - - - - - - section 5.6.2.7 on page 5-48
page 5-48
page 5-49
page 5-51
page 5-52
section 5.7 on page 5-53
- - - - - - - - - - - - - - - - - - section 5.3.7 on page 5-32
- - - - - - - - - - - - - - - - - section 5.3.7.2 on page 5-32
- - - - - - - - - - - - - - - - - section 5.3.7.3 on page 5-33
C －8
JMA-9100 Instruction Manual
│
│
│
├
├
│
│
├
│
│
├
└
C.5
5.
6.
7.
8.
9.
├ 3. Filter Display - - - ├ 4. ENT
└ 6. Filter Mode - - - - Target Number Display - - AIS Alarm Setting - - - - - ├ 1. Lost Alarm- - - - - └ 2. CPA/TCPA Alarm - Message - - - - - - - - - ├ 1. Addressed Message
└ 2. Broadcast Message
Display Lost TGT Data - - Own Ship's AIS Data - - - -
C.Menu Index
C.5 AZ
- - - - - - - - - - - - - - - - - - - - section 5.3.7.4 on page 5-34
section 5.3.7.5 on page 5-34
- section 5.3.6 on page 5-31
- section 5.3.9 on page 5-36
section 5.3.9.1 on page 5-36
section 5.3.9.2 on page 5-36
section 5.3.5.5 on page 5-29
- - - - - - - - - - - - - - - - - - - - section 5.3.5.6 on page 5-31
- - - - - - - - - - - - - - - - - - - - section 5.3.5.7 on page 5-31
AZ
├
├
├
├
└
1. AZ 1- - - 2. AZ 2- - - 3. Make AZ 1
4. Make AZ 2
5. ENT
section
section
section
section
5.2.1.1
5.2.1.1
5.2.1.1
5.2.1.1
on
on
on
on
page
page
page
page
5-14
5-14
5-14
5-14
C －9
JMA-9100 Instruction Manual
C.6
C.Menu Index
C.6 Track
Track
├
│
│
│
│
│
│
│
│
├
├
├
├
│
│
│
│
│
│
├
│
│
│
│
│
│
├
│
│
│
│
│
│
├
│
│
│
│
1. DISP Own Track Color - - - - - ├ 1. All
├ 2. White
├ 3. Cyan
├ 4. Blue
├ 5. Green
├ 6. Yellow
├ 7. Pink
└ 8. Red
2. Clear Own Track Color - - - - - 3. Track Type - - - - - - - - - - - 4. Num/Vector Display - - - - - - - 5. File Operations
├ 1. Select Card Slot
├ 2. Load Mode
├ 3. Load
├ 4. Save
├ 5. Erase
└ 6. Card Own Track Display
6. Water Depth Setting - - - - - - - ├ 1. Depth setting (MIN)
├ 2. Depth setting
├ 3. Depth setting
├ 4. Depth setting
├ 5. Depth setting
└ 6. Depth setting (MAX)
7. Water TEMP Setting - - - - - - - ├ 1. Temperature setting (MIN)
├ 2. Temperature setting
├ 3. Temperature setting
├ 4. Temperature setting
├ 5. Temperature setting
└ 6. Temperature setting (MAX)
8. Current Setting - - - - - - - - - ├ 1. Current Size
├ 2. Layer A
├ 3. Layer B
└ 4. Layer C
- - - - - - - - - - - - - - - - - - section 3.5.2 on page 3-40
- - - - - - - - - - - - - - - - - - section 3.5.5 on page 3-42
- - - - - - - - - - - - - - - - - - section 3.5.6 on page 3-42
- - - - - - - - - - - - - - - - - - section 3.5.6 on page 3-42
- - - - - - - - - - - - - - - - - - section 3.5.7 on page 3-44
- - - - - - - - - - - - - - - - - - section 3.5.8 on page 3-45
- - - - - - - - - - - - - - - - - - section 3.5.9 on page 3-46
C －10
JMA-9100 Instruction Manual
C.7
C.Menu Index
C.7 Route
Route
├
├
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
├
│
│
│
│
│
│
├
│
│
│
│
1. Select Route - - - - - - - - - - - - 2. WPT/Route Settig
├ 1. Waypoint Alarm - - - - - - - ├ 2. Route Alarm - - - - - - - - - ├ 3. Set Route Sequence- - - - - │
├ 1. Planned Speed - - - │
├ 2. Add - - - - - - - - - │
├ 3. Correct Position - - - │
├ 4. Correct Planned Speed
│
├ 5. Delete - - - - - - - - │
├ 6. Insert - - - - - - - - │
└ 7. New Monitor Route - ├ 6. Waypoint Input - - - - - - - ├ 7. Save Temporary Route
├ 8. Off-Track Limit Line - - - - - ├ 9. Next
├ 1. SEL. NUM/Comment Size - - ├ 2. Waypoint Vector - - - - - - - ├ 3. Status of Origin/DEST - - - - └ 4. WPT Number Display - - - - 3. WPT/Route Operations - - - - - - - ├ 1. Route Sequence- - - - - - - ├ 2. Waypoint Switch Mode - - - ├ 3. Waypoint Skip - - - - - - - - ├ 4. Waypoint Back Skip - - - - - ├ 5. Set/Cancel Waypoint
└ 6. Clear WPT/Route Data
4. File Operations - - - - - - - - - - - ├ 1. Select Card Slot - - - - - - - ├ 2. Load - - - - - - - - - - - - ├ 3. Save - - - - - - - - - - - - └ 4. Erase - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - section 3.7.1 on page 3-67
section 3.7.4.1
section 3.7.4.2
- section 3.7.2
section 3.7.3.5
section 3.7.2.2
section 3.7.2.3
section 3.7.2.4
section 3.7.2.5
section 3.7.2.6
section 3.7.2.1
- section 3.7.3
on
on
on
on
on
on
on
on
on
on
on
page
page
page
page
page
page
page
page
page
page
page
3-79
3-80
3-68
3-77
3-69
3-70
3-71
3-72
3-73
3-68
3-75
- - - - - - - - - - - - - - - section 3.7.6.1 on page 3-83
section 3.7.6.2
section 3.7.6.3
section 3.7.6.4
section 3.7.6.5
- section 3.7.5
section 3.7.5.1
section 3.7.6.6
section 3.7.5.2
section 3.7.5.2
- section 3.7.8 on page 3-87
section
section
section
section
3.7.8.1
3.7.8.3
3.7.8.2
3.7.8.4
on
on
on
on
on
on
on
on
on
on
on
on
on
page
page
page
page
page
page
page
page
page
page
page
page
page
3-83
3-84
3-85
3-85
3-81
3-81
3-86
3-82
3-82
3-87
3-88
3-87
3-89
C－ 11
JMA-9100 Instruction Manual
C.8
C.Menu Index
C.8 U.Map
U.Map
├
├
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
├
├
├
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
1. Own Ship Position - - - - - - - - - - - - - - - 2. Edit User Map - - - - - - - - - - - - - - - - - ├ 1. Make with Cursor - - - - - - - - - - - │
├ 1. Type
│
└ 2. Color
├ 2. Make with L/L - - - - - - - - - - - - - │
├ 1. Type
│
├ 2. Color
│
├ 3. L/L
│
├ 4. Comment
│
├ 5. Enter
│
└ 9. New Line Input/9.New Mark Input
├ 3. Move - - - - - - - - - - - - - - - - - ├ 4. Delete - - - - - - - - - - - - - - - - - ├ 5. Insert/Move Vertex - - - - - - - - - - ├ 6. Delete Vertex - - - - - - - - - - - - - └ 7. Delete by Type by Color - - - - - - - - 3. Shift - - - - - - - - - - - - - - - - - - - - - - 4. Shift Clear - - - - - - - - - - - - - - - - - - - 5. Mark Display Setting- - - - - - - - - - - - - - ├ 1. Display Mark Type- - - - - - - - - - - │
├ 1. All
│
├ 2. ○
│
├ 3. △
│
├ 4. ▽
│
├ 5. □
│
├ 6. ◇
│
├ 7. Wreck (mark)
│
├ 8. △△
│
├ 9. Next
│
├ 1. ▽▽
│
├ 2. △▽
│
├ 3. ▽△
│
├ 4. ＋
│
├ 5. ×
│
├ 6. Ｙ
│
├ 7. Hand drum (mark)
│
├ 8. Light house (mark)
│
├ 9. Next
│
├ 1. Trapezoid（mark）
│
├ 2. filled Trapezoid（mark）
│
├ 3. Hat(mark)
│
├ 4. ●●
│
├ 5. ●
│
├ 6. Filled Triangle(mark)
│
├ 7. ！
│
├ 8. anchor(mark)
│
├ 9. Next
│
├ 1. slash-anchor(mark)
│
├ 2. circle-dotted line(mark)
│
├ 3. non-dangerous wreck(mark)
│
├ 4. ◎
│
├ 5. mariner's event mark(mark)
│
├ 6. ・
│
├ 7. Wavy line (mark)
│
├ 8. Solid line (mark)
│
└ 9. Dashed-dotted line (mark)
├ 2. Display Mark Color - - - - - - - - - - │
├ 1. All
│
├ 2. White
│
├ 3. Cyan
│
├ 4. Blue
C －12
- - - - - - - - - - section 3.6.3.1 on page 3-52
- - - - - - - - - - - section 3.6.3 on page 3-52
- - - - - - - - - - section 3.6.1.1 on page 3-47
- - - - - - - - - - section 3.6.1.3 on page 3-49
section 3.6.3.2
section 3.6.3.3
section 3.6.3.4
section 3.6.3.6
section 3.6.3.7
section 3.6.4.1
section 3.6.4.2
- section 3.6.2
section 3.6.2.1
on
on
on
on
on
on
on
on
on
page
page
page
page
page
page
page
page
page
3-53
3-55
3-56
3-58
3-59
3-60
3-61
3-50
3-50
- - - - - - - - - - section 3.6.2.2 on page 3-51
JMA-9100 Instruction Manual
│
│
│
│
│
│
├
└
│
│
│
│
│
│
│
│
├ 5. Green
│
├ 6. Yellow
│
├ 7. Pink
│
└ 8. Red
├ 3. Mark Size - - - - └ 4. Comment Font Size
6. Geodetic - - - - - - - - 7. File Operations - - - - - ├
├
├
├
├
├
└
1.
2.
3.
4.
5.
6.
7.
Select Card Slot
Load Mode - - - Load - - - - - - Unload - - - - - Save - - - - - - Erase - - - - - - Card Mark Display -
C.Menu Index
C.8 U.Map
section 3.6.2.3
section 3.6.2.4
- section 3.6.6
- section 3.6.5
on
on
on
on
page
page
page
page
3-51
3-52
3-65
3-61
section
section
section
section
section
section
on
on
on
on
on
on
page
page
page
page
page
page
3-61
3-61
3-62
3-62
3-63
3-64
3.6.5.1
3.6.5.1
3.6.5.2
3.6.5.3
3.6.5.4
3.6.5.5
C －13
JMA-9100 Instruction Manual
C.9
C.Menu Index
C.9 Serviceman Menu
Serviceman Menu
├ Serviceman Menu - - - - - - - - - - - - - - - - - ├ 1. Adjust Menu
│
├ 1. Tune Adjustment - - - - - - - - - - - │
├ 2. Bearing Adjustment - - - - - - - - - - │
├ 3. Range Adjustment - - - - - - - - - - - │
└ 4. TXRX Adjustment
│
│
├ 1. Antenna Height - - - - - - - - │
│
├ 2. Tune Peak Adjustment- - - - - │
│
├ 3. Tune Indicator Adjust - - - - - │
│
├ 4. MON Adjustment - - - - - - - │
│
├ 5. MON Indicator Adjustment - - - │
│
└ 6. Output Pulse - - - - - - - - - ├ 2. Installation Menu
│
├ 1. Installation Information- - - - - - - - - │
│
├ 1. Date
│
│
├ 2. Name
│
│
└ 3. Company
│
├ 2. Master/Slave - - - - - - - - - - - - - │
├ 3. Sector Blank- - - - - - - - - - - - - - │
│
├ 1. Sector1 - - - - - - - - - - - - │
│
├ 2. Sector2 - - - - - - - - - - - - │
│
├ 3. Sector3 - - - - - - - - - - - - │
│
├ 4. Make Sector1 - - - - - - - - - │
│
├ 5. Make Sector2 - - - - - - - - - │
│
└ 6. Make Sector3 - - - - - - - - - │
├ 4. CCRP Setting - - - - - - - - - - - - - │
├ 5. COM Port Setting - - - - - - - - - - - │
│
├ 1. Baud Rate - - - - - - - - - - - │
│
│
├ 1. COMPASS
│
│
│
├ 2. MAINTENANCE/LOG
│
│
│
├ 3. NAV1
│
│
│
├ 4. NAV2
│
│
│
├ 5. ALARM
│
│
│
├ 6. JARPA
│
│
│
├ 7. AIS
│
│
│
├ 8. BRIDGE NET
│
│
│
├ 9. Next
│
│
│
├ 1. ARPA
│
│
│
└ 2. COM
│
│
├ 2. RX Port - - - - - - - - - - - - │
│
│
├ 1. GPS
│
│
│
├ 2. DLOG
│
│
│
├ 3. Alarm
│
│
│
├ 4. Depth
│
│
│
├ 5. Temperature
│
│
│
├ 6. Wind
│
│
│
├ 7. Current
│
│
│
├ 8. ROT
│
│
│
├ 9. Next
│
│
│
└ 1. RSA
│
│
├ 3. RX Sentence - - - - - - - - - │
│
│
├ 1. GPS(LL/COG/SOG)
│
│
│
├ 2. GPS(WPT/TIME)
│
│
│
├ 3. Depth
│
│
│
├ 4. Wind
│
│
│
└ 5. Current
│
│
│
│
├ 1. Data Set Number
│
│
│
│
├ 2. Layer A
│
│
│
│
├ 3. Layer B
│
│
│
│
└ 4. Layer C
│
│
├ 4. TX Port - - - - - - - - - - - - │
│
│
├ 1. TTM(TT)
C －14
- - - - - - - - - - - - section 7.1.1 on page 7-1
- - - - - - - - - - - - section 7.1.3 on page 7-5
- - - - - - - - - - - - section 7.1.4 on page 7-7
- - - - - - - - - - - - section 7.1.5 on page 7-7
- - section 7.1.8 on page 7-9
- section 7.1.3.1 on page 7-5
- section 7.1.3.2 on page 7-6
section 7.3.4.1 on page 7-31
section 7.3.4.2 on page 7-32
- section 7.2.4 on page 7-18
- - - - - - - - - - - section 7.2.8 on page 7-21
section 7.2.5.1 on page 7-19
- section 7.2.2 on page 7-16
section 7.2.2.1
section 7.2.2.1
section 7.2.2.1
section 7.2.2.2
section 7.2.2.2
section 7.2.2.2
- section 7.1.9
- section 7.2.1
section 7.2.1.1
on
on
on
on
on
on
on
on
on
page
page
page
page
page
page
page
page
page
7-16
7-16
7-16
7-16
7-16
7-16
7-10
7-12
7-12
- - - - - - - - - - section 7.2.1.2 on page 7-13
- - - - - - - - - - section 7.2.1.3 on page 7-14
- - - - - - - - - - section 7.2.1.4 on page 7-15
JMA-9100 Instruction Manual
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
├
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
├
│
├ 2. TLL(TT)
│
├ 3. TTD(TT)
│
├ 4. TLB(TT)
│
├ 5. OSD
│
├ 6. RSD
│
├ 7. ALR
│
├ 8. ACK
│
├ 9. Next
│
├ 1. TTM(AIS)
│
├ 2. TLL(AIS)
│
├ 3. TTD(AIS)
│
├ 4. TLB(AIS)
│
├ 5. Remote Maintenance
│
├ 6. JRC-ARPA
│
├ 7. NMEA0183 Output Format
│
├ 8. NMEA0183 Talker
│
├ 9. Next
│
├ 1. NMEA0183 TX Interval
│
├ 2. APB
│
├ 3. BOD
│
├ 4. GGA
│
├ 5. GLL
│
├ 6. RMC
│
├ 7. RMB
│
├ 8. VTG
│
├ 9. Next
│
├ 1. XTE
│
├ 2. BWC
│
├ 3. HDT
│
└ 4. THS
├ 7. Line Monitor
│
├ 1. COMPASS
│
├ 2. MAINTENANCE/LOG
│
├ 3. NAV1
│
├ 4. NAV2
│
├ 5. ALARM
│
├ 6. JARPA
│
├ 7. AIS
│
├ 8. BRIDGE NET
│
├ 9. Next
│
├ 1. ARPA
│
├ 2. COM
│
├ 3. TXRX/ISW
│
├ 4. KEYBOARD1
│
└ 5. KEYBOARD2
6. Alarm System - - - - - - - - - - - - - - ├ 1. Watch Alarm
│
├ 1. Reset Interval - - - - - - │
└ 2. Trackball Threshold - - - ├ 2. Relay Output - - - - - - - - - - │
├ 1. Relay Output Mode
│
├ 2. TT CPA/TCPA
│
├ 3. AIS CPA/TCPA
│
├ 4. New Target
│
├ 5. Lost
│
└ 6. RADAR Alarm
├ 3. ALR Output - - - - - - - - - - - │
├ 1. System Alarm
│
└ 2. TT/AIS Alarm
├ 4. Sound Output Mode - - - - - - - ├ 5. External ACK Setting - - - - - - │
├ 1. Critical Alarm
│
│
├ 1. Audio
│
│
├ 2Indication
│
│
└ 3. Acknowledge State
│
├ 2. Normal Alarm
│
│
├ 1. Audio
│
│
├ 2. Indication
│
│
└ 3. Acknowledge State
7. Inter Switch
C －15
C.Menu Index
C.9 Serviceman Menu
- - - - - - - - - - section 7.2.9 on page 7-22
- - - - - - - - - section 7.2.9.1 on page 7-22
- - - - - - - - - section 7.2.9.2 on page 7-22
- - - - - - - - - section 7.2.9.3 on page 7-23
- - - - - - - - - section 7.2.9.4 on page 7-23
- - - - - - - - - section 7.2.9.6 on page 7-25
- - - - - - - - - section 7.2.9.5 on page 7-24
JMA-9100 Instruction Manual
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
├
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
│
└
│
│
│
│
│
│
│
│
│
│
│
│
│
C.Menu Index
C.9 Serviceman Menu
│
├ 1. ISW Install
│
├ 2. Mask Setting
│
│
├ 1. No.1 Connection/No.1 Master
│
│
├ 2. No.2 Connection/No.2 Master
│
│
├ 3. No.3 Connection/No.3 Master
│
│
├ 4. No.4 Connection/No.4 Master
│
│
├ 5. No.5 Connection/No.5 Master1
│
│
├ 6. No.6 Connection/No.6 Masteri
│
│
├ 7. No.7 Connection/No.7 Masteri
│
│
└ 8. No.8 Connection/No.8 Masteri
│
└ 3. S-ISW TXRX Power Supply
├ 8. Language - - - - - - - - - - - - - - - - - - ├ 9. Next
├ 1. Input BP Count - - - - - - - - - - - - - - - ├ 2. TNI Blank - - - - - - - - - - - - - - - - - - │
├ 1. TNI Blank - - - - - - - - - - - - - - │
└ 2. Make Sector - - - - - - - - - - - - - ├ 3. Device Installation - - - - - - - - - - - - - - │
├ 1. Gyro
│
├ 2. Compass
│
├ 3. GPS Compass
│
├ 4. LOG
│
├ 5. 2AXW
│
├ 6. 2AXG
│
└ 7. GPS
├ 4. Network
│
├ 1. Network Function
│
└ 2. IP Address
3. Maintenance Menu
├ 1. Safety Switch - - - - - - - - - - - - - - - - ├ 2. Area Initial - - - - - - - - - - - - - - - - - - │
└ 1. Partial Master Reset - - - - - - - - - │
│
├ 1. Serviceman Menu
│
│
├ 2. Except Serviceman Menu
│
│
├ 3. User Setting
│
│
├ 4. TT Setting
│
│
├ 5. AIS Setting
│
│
├ 6. Day/Night
│
│
└ 7. JRC Card Copy Record
│
└ 2. All Master Reset - - - - - - - - - - - ├ 3. Internal To Card2 - - - - - - - - - - - - - - ├ 4. Card2 To Internal - - - - - - - - - - - - - - ├ 5. TXRX Time - - - - - - - - - - - - - - - - - │
├ 1. Clear TX Time - - - - - - - - - - - - │
├ 2. Clear Motor Time - - - - - - - - - - │
├ 3. TXRX to Display Unit - - - - - - - - │
└ 4. Display Unit to TXRX - - - - - - - - └ 6. String Data Update - - - - - - - - - - - - - 9. RADAR/TT Initial Setup
├
│
│
├
│
│
│
│
│
│
└
│
│
1. Signal Processing - - - ├ 1. Echo Noise Level
└ 2. Setting Mode - 2. TT- - - - - - - - - - - ├ 1. Vector Constant ├ 2. Video TD Level ├ 3. Video High Level
├ 4. Video Low Level
├ 5. Gate Size
└ 6. Limit Ring
3. MBS- - - - - - - - - - ├ 1. MBS Level- - - └ 2. MBS Area - - - -
- - - - - - - - section 7.2.6 on page 7-20
section 7.2.5.2 on page 7-19
- section 7.2.3 on page 7-17
section 7.2.3.1 on page 7-17
section 7.2.3.2 on page 7-17
- - section 7.1.6 on page 7-8
- - - - - - - - section 7.4.1 on page 7-33
- - - - - - - - section 7.4.2 on page 7-34
- - - - - - - section 7.4.2.1 on page 7-34
section 7.4.2.2
section 7.4.3.1
section 7.4.3.2
- section 7.4.4
section 7.4.4.1
section 7.4.4.2
section 7.4.4.3
section 7.4.4.4
- section 7.4.5
- section 7.3.1 on page 7-26
section 7.3.1.1
section 7.3.1.2
- section 7.3.2
section 7.3.2.1
section 7.3.2.2
on
on
on
on
on
on
on
on
on
on
on
on
on
on
page
page
page
page
page
page
page
page
page
page
page
page
page
page
7-34
7-35
7-35
7-36
7-36
7-36
7-37
7-37
7-38
7-26
7-27
7-27
7-27
7-28
- - - - - - - - - - - - - - - - - - - section 7.3.3 on page 7-29
- - - - - - - - - - - - - - - - - - section 7.3.3.1 on page 7-29
- - - - - - - - - - - - - - - - - - section 7.3.3.2 on page 7-30
1.Only for ISW Extended Mode
C －16
JMA-9133-SA
JMA-9132-SA
JMA-9123-7XA/9XA
JMA-9122-6XA/9XA/6XAH
JMA-9110-6XA/6XAH
MARINE RADAR
EQUIPMENT
INSTRUCTION
MANUAL
For further information,contact:
Not use the asbestos
URL
http://www.jrc.co.jp
Marine Service Department
Telephone : +81-3-3492-1305
+81-3-3779-1420
Facsimile :
tmsc@jrc.co.jp
e-mail :
AMSTERDAM Branch
Telephone : +31-20-658-0750
+31-20-658-0755
Facsimile :
service@jrcams.nl
e-mail :
SEATTLE Branch
Telephone : +1-206-654-5644
Facsimile :
+1-206-654-7030
e-mail :
service@jrcamerica.com
CODE No.7ZPRD0685
01ETM
MAY. 2008 Edition 2
ISO 9001, ISO 14001 Certified
JRC
Printed in Japan

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-702
Modify Date                     : 2008:09:02 14:34:25-04:00
Create Date                     : 2008:09:02 14:33:09-04:00
Metadata Date                   : 2008:09:02 14:34:25-04:00
Creator Tool                    : FrameMaker 8.0
Format                          : application/pdf
Title                           : JMA-9100 series RADAR Instruction Manual
Description                     : Instruction Manual
Creator                         : Japan Radio Co.,Ltd Marine Radar Group
Document ID                     : uuid:c06c7579-c9e8-434b-9a26-36fcc98d8d50
Instance ID                     : uuid:a74e4475-6ee6-4e32-a74e-5f2f8afaee46
Producer                        : Acrobat Distiller 7.0 (Windows)
Has XFA                         : No
Page Count                      : 140
Subject                         : Instruction Manual
Author                          : Japan Radio Co.,Ltd Marine Radar Group

EXIF Metadata provided by EXIF.tools