Jasco 45138 Signal Repeater (318MHz Transceiver) User Manual rp j01 ui

Download:
Mirror Download [FCC.gov]
Document ID	889492
Application ID	uPximzfNrdLfFYxqpsfIgw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	0.9kB (11245 bits)
Date Submitted	2008-01-16 00:00:00
Date Available	2008-01-16 00:00:00
Creation Date	2007-12-13 10:58:44
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2007-12-13 10:58:44
Document Title	Microsoft Word - rp-j01_ui.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	Joe Ng

REPEATER Model 45138
1. INTRODUCTION
The Repeater model 45138 is designed to increase the range of the sensors by boosting and
repeating signal from sensors to receiver unit.
In this package, you should find a Repeater and user’s instruction.
Please follow the instructions below to setup your Repeater.
2. INSTALLATION
POWER UP
i) Plug the repeater into an electrical outlet. The red light on the receiver should be off after being
plugged into an electrical outlet.
ii) Straight up the antenna in vertical position.
LOCATION
Put the repeater in your desired location, preferably at least 3 feet above the ground and centrally
located between the furthest sensors and the receiver unit in which it communicates. To obtain
the best performance, the environment around the repeater you placed should not be near any
other wireless devices in order to avoid interference.
PROGRAMMING
You need to do the programming in order to add the sensor to communicate with the receiver.
i) With the repeater is plugged into an electrical outlet.
ii) Press and hold the learn button on the left hand side of the repeater for approx. 15 seconds.
The red LED on the repeater will flash slowly.
iii) Activate the assigned sensor you want to program to the repeater.
iv) The repeater red LED will go off indicates the programming is completed.
TESTING
Activate your existing sensor to transmit the signal in front of the repeater. The distance between
the sensor and the repeater should be at least 1 to 2 feet. When the repeater receives and
repeats the signal, the red LED light on the repeater will flash.
CAUTION
RISK OF ELECTRICAL SHOCK, FOR INDOOR USE ONLY.
CAUTION : DISCONNECT POWER BEFORE SERVICING.
Maximum Rating:
Input : 120VAC 60Hz 2W
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This is device must
accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARRANTY
If, within one year from date of purchase, this product should become defective (except battery),
due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of
purchase and a Return Authorization are required.
CUSTOMER SERVICE
If you would like to order other products or have difficult getting them to work, please:
CUSTOMER SERVICE
JASCO PRODUCTS COMPANY
10E, Memorial, Oklahoma City, OK 73114 USA
Tel:405-302-2370

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2007:12:13 10:58:44+08:00
Create Date                     : 2007:12:13 10:58:44+08:00
Format                          : application/pdf
Title                           : Microsoft Word - rp-j01_ui.doc
Creator                         : Joe Ng
Document ID                     : uuid:5dc9034d-24fb-43cc-be86-20282f475ee5
Instance ID                     : uuid:6029a96f-82dd-4141-b523-ab2a58a8cbed
Page Count                      : 2
Author                          : Joe Ng

EXIF Metadata provided by EXIF.tools