Jeckson Electric 547-47-1012-R 433MHz Mid Line Remote (433.92MHz Rx) User Manual

Download:
Mirror Download [FCC.gov]
Document ID	711640
Application ID	Q1jGYHglPR9PlUgjE4B37w==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	185.09kB (2313674 bits)
Date Submitted	2006-10-03 00:00:00
Date Available	2006-10-03 00:00:00
Creation Date	2006-09-14 11:54:12
Document Lastmod	2006-10-03 10:03:11
Document Title	User Manual

Owner's Manual
Mid Line Remote
MODEL: 47—1012—T, 47—1012—R
Transmitter: FCC ID: ELY547-47-1012-T IC 1492A-471012T
Receiver: FCC ID: ELY547-47-1012-R IC 1492A-471012R
REMOTE CONTROL
The remote control has a range of approximately 50 ft. (15.25m), it does not have to be
pointed at the fireplace and can pass through most obstacles (including walls). It is
supplied with 243 independent frequencies to prevent interference with other units.
BATTERY lNSTALLATlON
1. Depress tab on the battery cover on the back of the remote transmitter and remove
batten/ cover.
2. Install 2 AAA batteries into the remote control. (included)
3. Replace the battery cover.
NOTE
The remote transmitter has a battery backup time of 24 hours. The batteries can be
removed for up to 24 hours before the transmitter will require re-initialization.
RECEIVER BOARD
1. Locate and connect the correct the input and output terminals to the correct terminals.
REMOTE CONTROL FUNCTION
FLAME/HEAT ONIOFF BUTTON 6
Press the Flame/Heat On/Of‘f button to turn the Flame/Heat function ON or OFF. When the
heater function is ON, the icon is displayed on the remote control in the upper left hand
corner. When this icon is displayed, the red indicator light is activated on the firebox.
NOTE
When using the remote control the heater runs on a thermostat. Press the or direction
keys to adjust the set temperature. Once the desired set temperature is reached the
heater will turn OFF. The heater will cycle ON and OFF to maintain the desired set
temperature.
PURIFIRE ONIOFF BUTTON D
Press the F'urifireTM On/Off button to turn the PurifireTM function ON or OFF. When the
PurifireW function is ON and the Heater icon is NOT displayed on the remote control, the
green indicator light is activated on the firebox.
NOTE
To turn the Flame/Heat and PurifireTM ON or OFF at the same time, press both control
buttons simultaneously.
DIMMER g
Press the left “—“ or right “+" direction button to decrease or increase the brightness of the
upper lights.
NOTE
The bar graph located on the display screen indicates the upper light brightness range.
FLAME SPEED “g-
Press the left “—“ or right “+" direction buttons to decrease or increase the flame speed.
NOTE
The bar graph located on the display screen indicates the speed range of the flame.
"OE
COUNTDOWN TIMER REP
To set the Countdown timer, press the left -“ or right “+” direction buttons to decrease or
increase by 30 minute decrements or increments. The countdown timer can be set from 30
minutes to 8 hours. The fireplace will automatically turn OFF when the sleep timer reaches
0 minutes.
PURIFIRE SPEED
The F’urifireTM includes a high efficiency filter to help improve the quality of air. When the
F’urifireTM function is ON, the green indicator light is activated on the firebox. Press the left
“e“ or right “+” direction buttons to select LOW or HIGH.
NOTE
The PurifireiM can also be turned On/Off by pressing the PurifireTM On/Off button.
SET TEMPERATURE ‘l:
Press the or right “+” direction button together of i J to select between °F and “C.
Press the “—“ or right + direction button to decrease orto increase temperature.
INITIALIZING THE REMOTE CONTROL
1. Plug cord into 120 volt wall outlet.
2. Set the 3 position manual control to Position 1 (left position).
3. Press and hold the initialization button on the Switch Power.
4. While holding the initialization button, press the flame ON/OFF button or the
F’urifire’M ON/OFF button ' on the remote control transmitter,
5. Release the initialization button on the Switch Board. The remote control is now ready
for operation.
0 0 _
z inoicator 3 POStIiOH
Light Manual
Control
CAUTION
1, For indoor use in dry areas only.
2. 120 volt AC supply.
Switch Board Panel
mm: are
WARNING
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on. the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
l Increase the separation between the equipment and receiver.
l Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
iii Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation issubject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
SPECIFICATIONS
Input Rating .........................
Output Rating ......................
Resistive Load ........
Incandescent Lamp.
Operation Temperature. .. 0 - 40°C
Storage Temperature ............................................................................ -25 — 60°C
.AC 120V, 60HZ
.. AC 120V, GOHZ
................................................................... 1200W

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
XMP Toolkit                     : 3.1-701
Create Date                     : 2006:09:14 11:54:12Z
Modify Date                     : 2006:10:03 10:03:11+08:00
Metadata Date                   : 2006:10:03 10:03:11+08:00
Format                          : application/pdf
Document ID                     : uuid:bac7161e-bcaa-4554-a2a4-5d72e3715719
Instance ID                     : uuid:19c02eab-8d58-41a6-a88f-b95d6b79c183
Has XFA                         : No
Page Count                      : 5

EXIF Metadata provided by EXIF.tools