Jenn Air JS42PPDBDA User Manual BUILT IN REFRIGERATOR Manuals And Guides L0410282
JENN-AIR Side by Side Refrigerator Manual L0410282 JENN-AIR Side by Side Refrigerator Owner's Manual, JENN-AIR Side by Side Refrigerator installation guides
User Manual: Jenn-Air JS42PPDBDA JS42PPDBDA JENN-AIR BUILT-IN REFRIGERATOR - Manuals and Guides View the owners manual for your JENN-AIR BUILT-IN REFRIGERATOR #JS42PPDBDA. Home:Kitchen Appliance Parts:Jenn-Air Parts:Jenn-Air BUILT-IN REFRIGERATOR Manual
Open the PDF directly: View PDF 
.
Page Count: 6
| Download | |
| Open PDF In Browser | View PDF |
Installation Instructions Installation Tool Requirements: Tape measure Level Stud finder INSTALLER Doors Drill with various bits [] [] [] [] [] Socket set Utility knife Magnetic extended screwdriver Phillips screwdriver Torx Bit Cardboard, Checklist: carpet remnant Handles are solidly attached to doors. Doors seal completely to refrigerator cabinet. Assure correct door handle alignment. Frame models. Assure door seals are not pinched. Do not drive screws / sharp objects into the doors. Leveling or other [] L Brackets are secure to 2x4 wood block. [] Stabilizing legs are against floor. Cabinet is secure. [] Toe kickplate is properly attached to refrigerator and aligned with floor. protective material for flooring Steel Hanger Strap Icemaker [] Water supply to refrigerator is turned on and lines flushed. [] Water leaks are not present at connection between household water supply and refrigerator. [] lcemaker arm is down for ice production. [] PuriClean ® Ice and Water Filtration System is installed correctly, if applicable. [] Purge water from the fountain on dispenser models. Preparing the Space: Front View IX (48"/121.9) (42"/106.7) 47 41 1/2"/120.7 112"1105.4 Electrical supply needs _. to be located in this area. Make sure the opening where the unit will be installed, is properly prepared for "Cut Out" dimension. Check placement for electrical outlet and water line. (Fig. 1) Side View NOTE: ,L ""_ For the door to open properly, it must be able to open at least 90 degrees. For installation in a corner, a 2" filler strip is required to ensure the 90 degree opening. The floor under the refrigerator is to be level with the surrounding floor. To protect the floor when moving the refrigerator, place cardboard, or preferably a carpet remnant (backing up) on the floor. 17.78 _ 9_--2 '1 10,1_ 5.08 _WARNING: (48"/121.9 42"/106.7' 83 3/4" 212.7 Front Rear 75 1/2" 191.8 Plumbing 3 1/2"--_ I Water supply )eels to _'49_ located in the shaded area. Fig. I Electrical Connection: This appliance is designed to operate on a normal 115 volt, 15 amp, 60 cycle line. There should be a separate, grounded circuit serving this appliance only. Do not use an extension cord. Do not use any device that will alter the electrical performance of this appliance. For the placement of the electrical outlet refer to Fig. 1. *Do not use a ground fault circuit interupter. Connection: Rough in the water line for the location (Fig. 1). Connect a 1/4" copper line to the house supply. Use a shut off valve between the refrigerator and supply. The shut off should be a drilled saddle valve. Do not use a self-tapping valve. The icemaker operates on 30 to 120 PSI. Route the water line within a 1/2" of the wall and no higher than 3" from the floor. Allow at least 3' of excess copper tubing outside the wall or 3'-'_'_.62 floor for easy connection to the water valve. * Prior to connection assure that the water supply and the copper t tubes have been flushed until the water runs clear. Reverse Osmosis: the 'Yellow' valve Remove the water inlet connector from and attach to the 'Blue' valve. Assure that the water filter bypass plug is in place (See Disconnect wires from Yellow Valve. Fig. 3). Uncrating the Unit: Uncrate the unit. Remove the lower shipping bolts and brackets. Slide the unit off of the crate base. Remove and save the lower kick plate, anti-tipping brackets and mounting hardware. (Fig. 2a) Remove the grille, this will help when moving the unit. (Fig. 2b) GRILLEPANEL TOOLS NEEDED SWITCH 3/8" _ REMOVE KICKPLATE_ lr REMOVE SCREWS Fig. 2b Fig. 2a Water Line Installation: Connect the water supply to the water valve. Turn the water on and check for leaks. Plug the unit in. (Fig. 3) Biu!Valve :ves _ 1 C°P_I:wa:lve Fig. 3 Leveling: Slide the unit in place and raise the front and rear levelers until the unit touches the brackets. Use a 3/8" socket for raising and lowering the unit. On each wheel housing there are two 3/8" hex bolts. On the left side, the outside bolt will move the rear leveler and the inside bolt will move the front leveler. On the right side, the outside bolt adjusts leveler and the inside bolt will move the rear leveler The front levelers must be in contact with the floor. the leveling direction. legs, turn the hex screw Place compartment. in the counter the front (Fig. 4). To raise Front Leveler clockwise a level on lower ledge of the machine Level the unit front to back and side to side. This is to prevent tipping kickplate. the main power switch Locate compartment and toggle of the unit (See the switch "On". Fig. 7). Install the in the machine Install the grille panel. Fig. 4 90 ° Door Stop Both doors are designed doors to a 90 With the doors of the lower to open 135 °. To restrict supplied one or both opening use the door stops closed, screw a door stop into the underside in this kit. %,, pOOe ' ]) hinge plate (Fig. 5). Lower Hinge Plate _...._/f_ ____/ .!/ 9toDO°r ____H°Ie _Door Stop _4ounting Fig. 5 Blocking the Unit: If there More is a solid soffit above the unit and the clearance or less you will not need to block the unit. clearances of more and brackets than provided is 1" For installations 1" clearance: Use the anti-tipping kit provided with the shipping crate. Locate and mark the 2 wall studs behind the unit. Mark where the "L" brackets with 1", you must use the anti-tipping than 2x4 and 2x4 will be located (Fig. 6). and drill 2 pilot holes 1/8". Locate the proper height to clear the unit. The space between the top of the unit and bottom of the wood block must not exceed 1/4". Secure the "L" brackets, using the provided screws, into the wall studs (,_1)). Make sure the screws will extend 7/8" into the wall studs. Align the pilot holes with the "L" brackets and secure the 2x4 with the screws provided(,_,5_). More than aR 1" -Wall Studs._ i I/ I I I I I Fig. 6 / Fi8. 7 Installing Backer Panels: Remove the door handle adhesive phillips or trim piece on overlay side of the packaging screwdriver Replace (Fig. 8b). the molding (Fig 8d). of the upper If the thickness Cardboard cover screws Do not pinch door seal when molding The backer backed hides the handle to pull it away from door (Fig. 8a). panel molding. DO NOT REMOVE needs to be under To install the foam. objects reinstalling the backer Slide the backer is less than a 1/4", back it up with a sheet Steel application. or sharp backed molding panel into position. (Fig 8c). panel for Stainless Do not drive A magnetic backed and reset the magnetic of the backer is recommended _&,CAUTION: Slide the backer in the channel, on the top and bottom models. tape on the magnetic panel or overlay Remove the trim. to obtain For panel size refer to Fig. 10. into the doors. handle. Grille Panel PhillipsScrewdriver Use Tape to Pul! Magnetic Molding Away from Door / :! r Fig. 8c For Screws _, CAUTION: J Fig. 8a Fig. 8b When attaching a raised wood panel of 1/2" or thicker secure the raised panel to the back of the grille cover frame. Use 4 #8 or similar screws. See illustration for approximate locations. Use the with a Install the handle. on the grille panel into place of shim material trim screws. the screws remove the screws and replace screws a 1t4" thickness. Panel Installation See section removal. panels With in post!on. Reinsert To replace Backer handle Torx screw for handle removed dispenser 2 Torx screws second Models: Panels" / trim piece To replace grille and remove panel. Dispenser for "installing panels, (see inset). and reinstall dispenser panel, / trim piece slide upper and lower I Grille Pane! I 8T43/4 '' slide out Spill Tray Insert handle I [ replacement 461/4" 40 1/4" I I / trim piece. open freezer door until 4 phillips screws that hold the door trim in place are accessible. Remove screws and slide out door trim. Close door and insert replacement panel. Reinsert Torx screw and reinstall door trim. T I Upper Freezer 20T" I Door Panel (48)2 (42)2 9/16" 7/16" b-..t (48)3 (42)1 7/16" 5/16" -I F.Refrigerator Door Panel Side Pane! (Dimensions Typ.) iiil 34" Lower Freezer Door Panel I_' 3/8" / _-(48)f7 (42)15 Spill Tray Grille J 26 1/16" 22 5116" / 5/16"-_ I 1/16"-- '-H t.-21t2,, / 27/16" I'1_ 24"u Fi_. I0 Fig. One-piece Overlay/Frame Panel Installation: See Owner Manual for switching "OFF O" the unit. Reference Fig. 9 for door panel removal and installation. With panels removed reattach hinge trim. Lift slide out Spill Tray grille and remove 2 Torx screws (]), (_). Remove stainless steel liner I_). Remove 2 Torx screws from dispenser control the control terminal panel inside panel to dispenser with 2 Torx screws. (_). Slide control to avoid terminal. Reinstall interfering panel down with one-piece Reattach control to remove. Disconnect panel Open door and slide one-piece I_). panel with 2 Torx screws. the Spill Tray grille and door trim. terminals Reposition on back of control stainless panel 1_) Terminals Control Panel I Stainless Steel Liner I I I O Spill Tray Grille 4 1_). Tuck Reconnect steel liner into track and secure Turn unit on. I I panel into position. Dispenser One-Piece Freezer Framed Panel ,!,1 I (D) (A) 42"Wide Cabinet 48" Wide Cabinet Inches Cm 69 1/8 175.6 69 1/8 175.6 (B) Panel Width 15 1/16 38.26 17 5/16 43.97 (C) Top of dispenser 20 5/8 52.39 20 5/8 52.39 35 7/16 90.01 35 7/16 90.01 2 7/16 6.19 2 9/16 6.51 1 5/16 3.33 3 3/8 8.57 Inches (A) Panel (D) Bottom Height cutout of dispenser (E) Left of dispenser to top of panel cutout to top of panel cutout width (F) Right of dispenser cutout width Cm ,,.(F) (B) Dispenser One-Piece Freezer Overlay Panel (D) (A) 42" Wide Cabinet 48" Wide Cabinet inches Cm Inches 69 1/8 175.6 69 1/8 175.6 (B) Panel Width 16 7/16 41.75 18 11/16 47.47 (C) Top of dispenser 21 3/16 53.82 21 3/16 53.82 34 13/16 88.42 34 13/16 88.42 2 1/16 5.24 2 3/16 5.56 2 1/4 5.72 4 3/8 11.11 (A) Panel (D) Bottom Height cutout of dispenser (E) Left of dispenser (F) Right of dispenser to top of panel cutout to top of panel cutout width cutout width Cm Installing Optional Side side panels Slide panel indicated batten Panels: and secure by the shaded is required panel (Fig. tall batten need to be 1/4-inch into position area (Fig. 1 la). between the cabinet 11 b). A 1/2-inch is required 1/4" side panel fitted up to the cabinet trim (top view) on Freezer side, A 3/16-inch and side Backside of Unit thick by 10 1/4-inch if the side panel extends into the machine compartment refrigerator (Fig. 1 lc). side thick. with screws up 1/4" side panel fitted up to the cabinet trim (top view) on Refrigerator side. Backside of Unit 1/2" area on the #8-32 Screw Screw > 3/16"/.48 Battens b----... 1/4"/.64 Side Panel of Unit Door Fig. lib 112"11.27 Battens on side of compartment (3/16"/,48 below the machine compartment) 1/4"/.64 Refrigerator Side of Unit Door Fig. I I c J Fig. I la Anchor the (Optional): Unit If you are attaching the unit to cabinetry, through both outer Install screws. Additionally: drill three trims. Drill 1/8" pilot holes If the depth/height steel hanger strap. secure cabinet. Double of opening over strap 3/16" holes into the cabinetry. is excessive at the achor use points , Drill 3 holes through vertical frame into cabinetry. Where applicable. (approx. location) to Adjust door hinges: Check to make sure the doors adjust the top hinges. movement. Remove the door hinge, which hinges by loosing after the doors adjusted magnetic and discard is located are adjusted. the small Extruded If not, for side to side phillips on the hinge. by loosening molding adjusted. are slotted the 3 large Torx screws. for alignment backed are properly The hinges screw on Adjust Tighten door handles the screws the top the screws under can be the (See fig. 8a). 111406-1 6 (060402)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 6 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Fri Apr 20 15:02:38 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools