Jensen Car Amplifier Lxa300 Users Manual 5528Eamp.p65
LXA300 to the manual 4bcc2285-4e5c-4d12-bd3f-2e63a451e67f
2015-01-24
: Jensen Jensen-Car-Amplifier-Lxa300-Users-Manual-341629 jensen-car-amplifier-lxa300-users-manual-341629 jensen pdf
Open the PDF directly: View PDF 
.
Page Count: 12
| Download | |
| Open PDF In Browser | View PDF |
® How to Install and Operate the LXA300 Amplifier Contents ® L VE LE AX M PO W IN F M SSST BA OO -B ER LP F 0 OF 25 ON HI 50 F HP 0 25 IN PU ER 50 OV T X- F LP LL F FU HP L LO W IN R PU T L PA SS R PR OT E CT Welcome! What you're holding in your hands is no ordinary owner's manual. We've tried to make the instructions in this book clear and easy to follow. For your Jensen amplifier to work right, it must be installed correctly. This manual will show you how to install your new amplifier like a pro. It's a good idea to read all of these instructions before you begin the installation. Most installations are straightforward and can be handled by a do-it-yourselfer with the right tools, patience, and the ability to follow instructions. But, do-it-yourself installation isn't for everyone. If you still don't feel confident after reading this book, consider turning the installation job over to someone better suited to it. Warranty Service If your Jensen amplifier should ever require service, you will need to have the original dated receipt. If you ever need to return the unit for any reason, always include the receipt with the product. Technical Assistance For technical assistance with the operation or installation of the LXA300, call 1-800-323-0221. Features ........................................ 2 Installation ................................... 2 Before You Begin Installation ..................................... 2 Amplifier Location .......................... 2 Disconnect Battery ........................ 2 • Amplifier Installation Kit ............. 2 Supplies and Tools Needed .......................................... 3 Routing Wires ................................ 3 • Bigger is Better .......................... 3 Wiring ............................................. 4 Power and Outputs ........................ 4 Power Terminal (BATT +12V) ........ 4 Ground Terminal (GND) ................. 4 Remote Terminal (RMT +12V) ....... 4 Fuses ............................................. 4 Inputs and Controls ....................... 5 Input Wiring .................................... 5 Pass Output ................................... 5 Power Light .................................... 5 Protect Light .................................. 5 Input Level Control ........................ 6 Bass Boost ..................................... 6 Crossover ...................................... 6 Speaker Wiring .............................. 7 Testing .......................................... 9 Reconnect Battery ......................... 9 Test Power Wiring .......................... 9 Test Speaker Connections ............ 9 • Dealing with Alternator Noise .......................................... 9 • Installing in Trunk ..................... 10 • Crimp Connections .................. 10 • Securing Wires ........................ 10 • Speaker and Power Wires ............................ 10 Troubleshooting ....................... 11 Specifications and Warranty ............................. 12 ® LXA300 Features The Jensen LXA300 power amplifier is a twochannel 300-watt total system power automotive amplifier. The LXA300 includes: • RCA inputs • High level inputs • Continuously variable low pass or high pass crossover • Bass boost feature • Remote turn on/off • Electronic protection circuitry to protect the amplifier from short circuit, DC offset and thermal overload • Unique, super-efficient heat sink design • 2 x 75 watts RMS per channel (2 x 150 watts peak) • Pass through connectors for adding other amps • 150 watts RMS bridged into a 4 ohm load • Bridgeable design to direct full power to one speaker Audio Amplifiers Amplification offers two advantages: • The LXA300 amplifier can make the sound of your receiver fuller and richer, even at low volume levels. • Many automotive receivers provide four to 10 watts at maximum power. At 75 watts RMS per channel (200 watts bridged), the LXA300 can be played substantially louder, permitting the use of more powerful speakers. Installation Before You Begin Installation Before you begin, you will need tools, supplies and adapters. It is best to make sure you have everything you need before you start. There is a list of supplies and tools on the next page. Disconnect Battery Before you begin, always disconnect the battery negative terminal. – + Amplifier Location Important Allow air circulation around the amplifier. The LXA300 amplifier’s compact design allows greater flexibility in mounting. It can be mounted under a seat or in the trunk. When selecting a location, remember that amplifiers generate heat. Select a location where air can circulate around the amplifier. Do not cover the LXA300 with carpets or enclose it behind interior trim panels. Do not mount the amplifier in an inverted or upside down configuration. Every installation will be a bit different based upon vehicle design. Check all locations and placements carefully before making any cuts or connections. 2 Important If wiring connections are made wrong, the unit will not operate properly and it could be damaged. Follow the installation instructions carefully, or have the installation handled by an experienced technician. Professional Tip Amplifier Installation Kit Your installation job will be much easier if you purchase an amplifier installation kit. These kits often include low-level RCA cables, extra large power and ground wires, a fuse or circuit breaker and connector for the battery. ® LXA300 Supplies and Tools Needed Routing Wires Supplies: • Speaker wire (12 gauge for subwoofers, 16-18 gauge for other speakers) • Sheet metal type screws for mounting amplifier • Electrical tape • Solderless crimp connectors • 1/2" thick plywood or particle board to mount amplifier on Battery Battery Connector Fuse or Circuit Breaker Tools: • • • • • Flat and Phillips screwdrivers Wire cutters Wire strippers Cordless or standard electric drill and drill bit set Crimping tool (if using solderless crimp connectors) • 12-volt test light or digital multimeter • Wire brush or scraper (to remove paint for a good ground connection to vehicle) • Soldering iron and rosin core solder (if you're going to solder your connections) Amplifier Installation Kit: You will need an amplifier installation kit to install your amp properly because it contains all the wire and connectors that you will need to hook up your new amp right the first time. If you want to purchase these items separately you will need the following: • 20-25 feet of 8 gauge wire • 30 amp fuse or circuit breaker (to be hooked up at the battery) • 20 feet of 18 gauge wire for the remote turn-on/ power antenna lead • RCA cable (for signal input from radio) – 20 feet for trunk installation – 12 feet for under-seat installation • Two 8 gauge ring terminals (one for the battery connection and the other for the ground connection at the amp). You may need two additional ring terminals if you are using a circuit breaker at the battery. • Two 8 gauge barrel connectors (you may need these depending on what type of fuse holder you have) • Two 8 gauge spade terminals (to hook up power at the amp) • Four 12 gauge spade terminals for subwoofers or 16-18 gauge spade terminals for other speaker connections to amp • One 18 gauge spade terminal for remote turn-on/ power antenna lead Grommet To prevent damage to power wire Receiver Power Wire (8 gauge wire or larger) Power Antenna Turn-on Wire (18 gauge wire) RCA Cables Speakers Amplifier Ground Screw Drill 1/8" hole in chassis sheet metal Use the same ground if using multiple amplifiers Professional Tip Bigger is better Stereo installation dealers sell extra thick power and speaker wires to ensure best sound. Look for 8 gauge power wire, especially if you have several amplifiers. 3 ® LXA300 Wiring Power and Outputs + 12V FUSE RMT GND L+ L– R– R+ 30A POWER Power Terminal (BATT +12V) Remote Terminal (RMT +12V) Connect directly to the vehicle battery+ terminal with 8 gauge wire (minimum). + 12V RMT SPEAKER GND Connect the radio power antenna lead from the receiver to the amplifier REMOTE terminal. This turns the amplifier on whenever the receiver is turned on. If a power antenna lead is not available, connect this wire to the radio or accessory fuse. + 12V Battery Terminal Adapter Install as close to the battery as possible RMT GND Spade Connector Not Supplied 30 amp Fuse or Circuit Breaker 8 Gauge Wire To Battery+ Terminal Spade Connector Butt Connector (not supplied) To Receiver Power Antenna Lead 18 Gauge Wire Ground Terminal (GND) Connect to a good chassis ground. The ground connection should be to clean, unpainted metal to provide a good electrical connection. + 12V RMT Fuses FUSE Use only one 30 amp blade-type fuse. GND 30A Ring Connector Sheet Metal Screw (supplied) Spade Connector 8 Gauge Wire Drill 1/8" hole in chassis sheet metal 4 ® LXA300 Inputs and Controls POWER PROTECT L HI INPUT R R L LOW INPUT PASS Input Wiring Pass Output Inputs may be high level (from the receiver's speaker) or low level (from special low level outputs). Low level input is preferred for best performance. R L Use pass through (PASS OUTPUT) connectors for adding other amplifiers. PASS Important Use only the low level or high level input, do not use both at one time. Power Light Low Level Input Use a pair of shielded stereo audio cables with RCA type jacks. Most trunk-mount amplifier installations require 20-foot RCA cables. Most under-seat and pickup truck installations use 12-foot cables. Connect RCA cables from your receiver to the RCA input jacks on the amplifier. High Level Input Connect left and right speaker wires coming from radio to high level input plug as shown. POWER The power light comes on when 12 volt power is available at both the battery +12 volt and RMT wires. Protect Light The red protect light comes on when the amplifier shuts down from PROTECT overheating or a short circuit (speaker failure). White-Left (+) White/Black-Left (–) Gray-Right (+) Gray/Black-Right (–) Black (ground) Radio L R L +– – + Splice (as necessary) R or POWER L HI INPUT R LOW INPUT Hi level input plug on amp 5 ® LXA300 BASSBOOST LEVEL Adjust the crossover to accommodate your chosen installation method. OFF ON MIN MAX LPF 50 250 HPF X-OVER LPF HPF FULL 250 Input Level Control The input level control matches the output of your radio to the input of the amplifier. After the installation is complete, make sure the input MIN MAX level control on the amp is turned down all the way (counterclockwise or all the way to the left). Play a tape or CD (make sure bass and treble settings or EQ are flat too) and turn the volume up slowly until you just start to hear distortion. Now back the volume down just a bit. On the amp, slowly turn up the input level control (clockwise or to the right) until you just start to hear distortion and back it down a bit. Now your radio and amplifier levels are matched. LEVEL Bass Boost OFF ON 6 • LPF–(low pass filter) only bass tones go to speakers. Use with woofers or subwoofer. X-OVER • FULL–all tones go to speakers. Use with full-range speakers. LPF HPF FULL • HPF–(high pass filter) blocks very low tones from the speakers. Use with 6" or smaller speakers. LPF 50 BASSBOOST Crossover (X-OVER) BASS BOOST increases the volume of bass by up to 6 dB at 45Hz. Use LPF and HPF to adjust from 50 to 250Hz. When using your Jensen amplifier 50 250 to run a subwoofer and two fullHPF range speakers (known as Trimode or three channel operation) you will need to purchase separate 50 250 high and low pass crossovers from your local retailer. A pair of high pass crossovers for your full range speakers and a low pass filter for the subwoofer. This will allow the amplifier to work properly when installing it in Tri-mode. Failure to install these filters may damage your amplifier and/ or your speakers. ® LXA300 Speaker Wiring 2 Speakers 2 Subwoofers RCA Cables RCA Cables 2/4Ω 2/4Ω 2/4Ω L+ L– R– R+ L+ 2/4Ω L– R– R+ X-OVER X-OVER LPF HPF FULL LPF HPF FULL 7 ® LXA300 2 Speakers + Subwoofer Bridged Subwoofer RCA Cables RCA Cables 2/4Ω 2/4Ω 4Ω 4Ω L+ L– R– L+ R+ L– R– R+ High Pass Filters X-OVER 4Ω minimum LPF HPF FULL Low Pass Filter (available at most car stereo installation stores) Important When running a subwoofer and two full-range speakers together (Tri-mode operation), high and low pass filters must be used. Failure to install these filters will damage your amp and/ or speakers. 8 X-OVER LPF HPF FULL ® LXA300 ✓ Testing Before you finish the installation, you should do the following tests to make sure the wiring is correct and everything is operating properly. Reconnect Battery When wiring is complete, reconnect the battery negative terminal. Professional Tip Dealing with Alternator Noise – + Test Power Wiring 1. Turn on the receiver but do not turn up the volume. The amplifier power light should come on. If not, check the RMT and +12V wires. 2. Turn up the receiver volume slightly. All speakers should operate. If not, check wiring connections at amplifier and speakers. The vehicle alternator can cause a “siren” sound in the speakers that changes with engine speed. To prevent alternator noise: • Do not bundle RCA cables with speaker or power wires • Do not run speaker wires parallel to power wires • If you have more than one amplifier, connect all ground wires to the same screw • Make sure all wires are as short as possible • Make sure the receiver black wire has a good connection to the vehicle chassis ground Test Speaker Connections These tests make sure the speakers are connected right. If speakers don’t play at all, one (or both) speaker wires may be disconnected. If the wrong speaker plays (you hear left speaker when you expect right speaker) make sure you connected the wires correctly. Once everything is operating correctly, reassemble vehicle trim and dashboard. 9 ® LXA300 Professional Tip Professional Tip Installing in Trunk Securing Wires When installing the amplifier in the trunk, run the power wires along the same path as the other vehicle wiring. Many cars have insulated channels for wiring. You will have to remove the door sill trim and the carpet. Be proud of your installation! Use wire ties to bundle wires together when possible. (But never bundle speaker wires and power wires together!) Professional Tip Crimp Connections Purchase crimp connectors and crimping tool. Connectors are color coded. 1. Strip 1/4 inch (6mm) of insulation from both wires. 2. Insert into connector. 3. Crimp tightly. You can make permanent splices (using butt connectors) or select connectors that can be removed and reinstalled. 1 Strip wire 1/4" (6mm) 10 2 3 Secure loose wires to the vehicle to make sure they don’t rub or rattle. Professional Tip Speaker and Power Wires Do not run speaker and power wires next to each other. Power wires can generate a “siren” sound in the speakers. Run speaker and power wires on opposite sides of the car. ® LXA300 Troubleshooting Problem Possible Cause Corrective Action Amplifier does not operate (power LED not on) when vehicle and radio are on No power to +12V terminal Repair wire or connections No power to remote wire with radio on Check connections to radio with test light Fuse blown Check fuse Radio volume needs to be turned up too high for amp to work Input level control (gain control) adjusted too low Adjust input level control (gain control) Radio volume is too sensitive Input level control adjusted too high Adjust input level control to lower setting Sound from only one speaker Defective speaker Replace speaker Poor connections to speaker (wire) Check connections Speaker wires shorting together Separate speaker wires and insulate RCA input cable defective Replace cable Sound distorted Input level control adjusted too high Adjust input level control Blows fuses Speaker wires shorting together Separate speaker wires and insulate Power wires hooked up incorrectly Check power wire connections Speakers blown or defective Check speakers Radio has poor noise immunity Disconnect audio inputs to amplifier – if noise disappears then the radio is at fault Improper ground connections Make sure radio and amplifier are grounded to the same point Loud pop in speakers when power is turned on or off Remote wire (blue) not properly connected Refer to page 4 for proper installation. If radio does not have a power antenna lead and you have connected the remote lead to an ignition source then you may get a “pop” in your speakers. This is not uncommon. You may have to put a switch in line with the remote lead to turn the amp on/off manually. Protect light comes on/ amplifier shuts down Amp is in thermal protection Let amp cool down before attempting to turn back on (some installations may require a fan to keep the amp cool, especially if you are driving subwoofers with the amp) Faulty speaker connection and/or crossover Check speakers and/or crossovers for loose or bad connections Low battery voltage Make sure you are getting between 10.8-15.6 volts to the amplifier with a digital multimeter measured at the amplifier Speaker impedance less than 2 ohms per channel If you are using 4 ohm speakers you cannot have more than two speakers wired in parallel per channel Amp will not operate into 2 ohms bridged Speaker wires not connected to speakers properly Refer to pages 5, 6 and 7 for proper installation Alternator whine in outputs (vehicle ignition noise) No output on channels Input hooked up incorrectly Can’t find cause of problem Contact Jensen Technical Assistance (1-800-323-0221) 11 Specifications LXA300 Amplifier Power output @ 14.4 VDC, 20-20 kHz ............ (4 ohms) 75 Watts per channel RMS, < 00.08% THD (2 ohms) 100 Watts per channel RMS, < 00.1% THD (4 ohms) bridged 200 Watts per channel RMS, < 00.1% THD Frequency Response .......................................................................................... 20 Hz-20 kHz ± 3 dB Signal to Noise Ratio @ Rated Power .................................................................................... >100 dB Channel Separation @ Ref. Power ............................................................................... >65 dB, 1 kHz THD & IMD @ Ref. Power into 2 ohms ..................................................................................... <0.1% Speaker Impedance .............................................................................................................. 2-8 ohms Input Impedance ............................................................................................................... 20 k ohms Crossover Frequencies ...................................................................................... Low/High: 50-250 Hz Power Requirement .................................................................. 14.4 VDC (10.8-15.6 VDC allowable) Fuse Requirements ........................................................................................ 30 amp blade-type fuse Dimensions ...........................................................2.25" x 11.125" x 8" (56.5mm x 282mm x 203mm) Specifications subject to change without notice. Limited One Year Warranty–USA and Canada Length of Warranty. This warranty from Recoton Mobile Electronics shall be in effect for a period of one year from the date of the first consumer purchase. If shipment of the product is required, it should be packed securely. The original dated bill of sale must always be included with the product as proof of warranty coverage. Persons Protected. This warranty will be enforceable by the original owner and any subsequent owners during the warranty period so long as proof of date of purchase from an authorized Jensen dealer is presented whenever warranty service is required. What We Will Pay For. We will pay for all labor and material expenses required to repair the product, but you must pay any labor costs for the removal and/or installation of the product. If the product is shipped for warranty service, you must prepay the initial shipping charges, but Jensen will pay the return shipping charges if the product is returned to an address inside the USA or Canada. What is Covered. Except as otherwise specified below, this warranty covers all defects in material and workmanship in this product. The following are not covered: damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product; damage occurring during shipment (claims must be presented to the carrier); elimination of car static or other electrical interferences; any product purchased outside USA or Canada, or on which the serial number has been defaced, modified or removed. How You Can Get Service. U.S. Purchasers. Please telephone Jensen at 1-800-323-4815. We will either inform you of the name and address of an authorized Jensen repair station which will service the product or will advise you to send the product to a factory service center. Canadian Purchasers. The product should be returned to the Jensen dealer from whom it was purchased and such dealer either will service or arrange for service of the product. Limitation of Implied or Statutory Warranties and Conditions. All implied or statutory warranties and conditions, including warranties or conditions of merchantability, fitness for particular purposes and non-infringement, are limited in duration to the length of this warranty. Exclusion of Certain Damages. Jensen’s liability is limited to the repair or replacement, at our option, of any defective product and shall not include incidental or consequential economic damages of any kind. Some states and/or provinces do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state and province to province. ® Recoton Mobile Electronics A Division of Recoton Audio Corporation A RECOTON® COMPANY 1090 Emma Oaks Trail Lake Mary, Florida 32746 ©1999 Recoton Audio Corporation
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Author : Diana Laine Create Date : 1999:12:02 08:45:35Z Modify Date : 2013:10:09 12:44:06-05:00 XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Format : application/pdf Creator : Diana Laine Title : 5528Eamp.p65 Creator Tool : PageMaker 6.5 Metadata Date : 2013:10:09 12:44:06-05:00 Producer : Acrobat Distiller 3.01 for Power Macintosh Document ID : uuid:74b78afc-2486-42aa-9d14-83a0b51b7f21 Instance ID : uuid:911e9490-e111-4a34-9d20-21cdf0de161f Page Count : 12EXIF Metadata provided by EXIF.tools