Jensen Vx7020 Installation Manual 128 9293 Guide 03 25 14

2014-12-11

: Jensen Jensen-Vx7020-Installation-Manual-120330 jensen-vx7020-installation-manual-120330 jensen pdf

Open the PDF directly: View PDF PDF.
Page Count: 6

What’s in the Box
The following items are supplied with
the VX7020:
• VX7020 Head Unit
• Trim Ring
• Hardware Bag
• Power/Speaker Output Harness
• Remote Control
• External Microphone
• GPS Antenna
• Owners Manual & Warranty Card
• Installation Guide
Tools and Supplies
The following tools and supplies are
needed to install the VX7020:
• Torx type,  at-head and Philips
screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screw
driver, socket wrench set or other
tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
WARNING! Never install this unit where operation and viewing could interfere with
safe driving conditions.
INSTALLATION GUIDE
VX7020
6.2” Double DIN Multimedia Receiver
DVD / NAV / SiriusXM-Ready®/ Built-in Bluetooth / Pandora Link
Compatible with iPhone /Compatible with iPod / USB / Aux In
1
Optional Equipment
• Steering Wheel Control (SWC)- The VX7020 is SWC ready for vehicles equipped with the option. See wiring diagram for
installation details. For SWC programming details, please see the operation manual.
• Rear Camera- The VX7020 is Rear Camera ready for vehicles equipped with the option. See wiring diagram for installation
details.
Disconnect the Battery
• To prevent a short circuit, be sure to turn o the ignition and remove the negative (-) battery cable prior to installation.
NOTE: If the VX7020 is to be installed in a car equipped with an on-board drive or navigation computer, do not disconnect the
battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution
during installation to avoid causing a short circuit.
Replacing the Fuse
• When replacing the vehicles Radio fuse always use the proper rated replacement fuse. Using a fuse with an improper rating
could damage the unit and cause a  re.
ISO-DIN Installation
The VX7020 is designed to  t into a 2.0 DIN dashboard opening. The unit has threaded holes in the chassis side panels which may be
used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount
the radio to the dashboard. Please consult with your local car stereo specialty shop for assistance on this type of installation.
NOTE: It is the end-users responsibility to install and operate this unit in a manner in accordance with local, state and federal laws.
The PARKING BRAKE wire MUST BE CONNECTED as directed in the manual.
Using the Cosmetic Trim Ring
A cosmetic trim ring is supplied with the head unit for installation
exibility. This unit will  t into most import dashes with little or no
modi cation to the dash board/cavity. Some US domestic vehicle
dashes will accept a Double-DIN chassis, but there is usually a
small gap between the radio and dash piece after installation is
complete. In this case, use the trim ring to conceal any gaps that
may be present.
1. Remove the existing factory radio from the dashboard or
center console mounting. Save all hardware and brackets as
they will be used to mount the new radio.
2. Remove the factory mounting brackets and hardware from the
existing radio and attach them to the new radio.
CAUTION! Do not exceed M5 X 6MM screw size. Longer screws
may damage components inside the chassis.
3. Place the radio in front of the dashboard opening so the wiring
can be brought through the mounting sleeve. Follow the
wiring diagram carefully and make certain all connections are
secure and insulated with wire nuts or electrical tape. After
completing the wiring connections, plug the ISO connectors
into the mating sockets on the rear of the chassis. Turn the
unit on to con rm operation (vehicle ignition switch must be
“ON”). If the unit does not operate, re-check all wiring until the
problem is corrected.
4. Mount the new radio assembly to the dashboard or center
console using the reverse procedure in step 1 above.
CAUTION! Be careful not to damage the car wiring.
NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 30° of horizontal. Make sure the unit is
mounted within this limitation.
Wiring Diagram
CAUTION! IMPORTANT: Incorrect wiring connections can damage the unit. Follow the wiring instructions carefully,
or have the installation handled by an experienced technician.
Need Help? For technical assistance, call the Jensen customer support line at 1-800-323-4815.
The VX7020 has a built-in SWC Interface compatible with most resistive type OE steering wheel controls. In most installations, only two of the three wires will be needed to
interface the OE steering wheel controls to the VX7020.
SWC A - Primary SWC Wire
SWC B - Secondary SWC Wire
SWC Ground - Chassis ground
Initial wiring of the SWC interface should include the SWC A and SWC Ground wire. If this combination of wiring does not support your vehicle functions, then try the SWC B
and SWC Ground wire combination. Do not use only SWC A and SWC B. The SWC Ground must be connected.
Some vehicles may not support all SWC functions. Professional Installation is recommended.
2
Black/SiriusXM
Black/MICROPHONE
BT Antenna
)
SPEAKER (-)
SPEAKER (+)
GROUND
BATTERY 12V (+)
ACC / IGNITION
BRAKE
REVERSE
POWER ANT & AMP. CONT
ILLUMINATION
LEFT FRONT SPEAKER (-)
LEFT FRONT SPEAKER (+)
RIGHT FRONT SPEAKER (-)
RIGHT FRONT SPEAKER (+)
LEFT REAR SPEAKER (-)
LEFT REAR SPEAKER (+)
RIGHT REAR SPEAKER (-)
RIGHT REAR SPEAKER (+)
BLACK
YELLOW
RED
PINK
GREEN/WHITE
BLUE
GRAY/BLACK
GRAY
GREEN/BLACK
GREEN
PURPLE/BLACK
ORANGE
PURPLE
KEY A
KEY B
WHITE/PURPLE
WHITE/BROWN
KEY GNDBROWN/BLACK
WHITE/BLACK
WHITE
SWC (BLACK)
NOTES:
3
128-9293
Voxx Electronics Corporation
Hauppauge, NY 11788
Technical Assistance: 1-800-323-4815
www.jensenmobile.com
© 2014
Printed in China
Installation Guide

Navigation menu