Jetson Electronic Technologies JET-TMT-02 TIRE PRESSURE SENSOR User Manual JET TPMS FOR car

Shenzhen Jetson Electronic Technologies Co.,Ltd TIRE PRESSURE SENSOR JET TPMS FOR car

User manual

(For Car)
SENSOR 2TYRE GUARD 1TYRE GUARD JET-M-300C(MONITOR)JET-M1-300C(MONITOR)JET-M2-300C(MONITOR)1 Introduction2 FunctionThe monitor’s function is to receive the temperature and pressure information transmitted from a sensor fitted to each tyre and display this information on the screen in the specific units of measurement of your choice.The monitor will emit an alarm when a tyre pressure or temperature varies markedly from the targeted tyre pressure and/or temperature. The system will detectthigh or low air pressure as well as high temperature or rapid leakage from the tyres. The monitor will flash the red LED icon and an alarm will sound to remind the operator to check if the tyres are high or low in air pressure, leakage, high temperature or the monitor’s battery is low, or there is a problem with a sensor. This advanced tyre monitoring system offers these great features and benefits, is reliable, lightweight and compact.3 Installation & Operating InstructionsThe following instructions show the identification of operating buttons of the monitor.Units ConversionTemperature Units ConversionF=9C/5+32Note: C = Celsius; F = Fahrenheit Pressure Units Conversion 1 Bar=14.5 psi1 Bar=100 kPa21 Bar=1.02 kgf/cminstalling the tyre sensors.vehicle’s tyres to your required pressures. Note: It is recommended to set tyre pressures at those recommended by the manufacturer listed in the vehicle’s handbook.“ ” button“” buttonSET buttonCongratulations on purchasing the new TYRE PRESSURE MONITORING (TPMS).This system is a safety system for monitoring vehicle’s tyre air pressure and temperature. It consists of external mounted tyre pressure wireless sensors fitted to the vehicle’s ryre valve and a hand-held monitor.The sensor will monitor the tyre’s air pressure and temperature.The sensor transmits the tyre pressure and temperature informationto the dash-mounted/hand-held monitor.SYSTEMin standby mode,press" "button to change the pressure unit,white press" "button to change the temperature unit.NUMBER ICAL INDICATING SECT IONMONITOR iconPRESSU RE CONDIT ION iconSENSOR i conTEMPER ATUR E ico nPRESSU RE UNIT ico n Please ensure the monitor is fully charged and in the tyre alignment mode beforeBefore installing sensors and setting the monitor,make sure you have inflated theThe monitor can be placed on the dashboard,on the sun visor or mounted in any convenient place in the vehicle.
4TYRE GUARD 3TYRE GUARD Tyre alignment modeHold down the “ ” and “ ” buttons simultaneously on the monitor for 5 seconds to enter tyre alignment mode, and press either “ ” or “ ” button to select the specific tyre that needs to be aligned. Screw a sensor to the tyre valve stem and the current pressure will be displayed against the corresponding flashing tyre icon on the screen. Once the tyre is aligned successfully the green light appears on the monitor. The red LED light appears on the monitor if the sensor hasn’t been aligned and “- - -” also appears on the monitor. Note: If the sensor is to be removed from one valve and fitted to another valve, you must delete the current setting on the monitor and realign this sensor to the new tyre. To delete an aligned sensor from a tyre, hold down the SET button for 5 seconds. When you exit the alignment mode, by again holding down the “ ” and “ ”, buttons simultaneously on the monitor for 5 seconds to check the pressures and temperatures, the monitor will indicate the data of the selected tyre. Click through to ensure all tyre pressures and temperature details are in accordance with your requirements. After your checks are completed, the backlight will go out and the monitor will indicate the tyre pressure of the selected tyre.Installation of the Sensor and anti-theft deviceIt’s very simple to install the sensors. Screw a sensor to each tyre valve stem as the picture shows.Note:1. Always install the sensor when the tyre is cold2. Please check each tyre valve is not damaged.3. Check to ensure there are no leaks and the sensors are firmly secured to each tyre valve.AValve Anti-theft DevceDrivercThe sensor has an anti theft ring to prevent the sensors being stolen. Firstly, place the anti_theft ring over the valve stem,with one side of the inner hexagon facing out, place the hexagon head of the sensor into the inner hexagon and then screw down the sensor; finally,place the inner hexagon screws of the anti-theft device and tighten with the key provided. Please refer to the right graphics A,B and C when installing the rings.Standard Pressure Setting Hold down SET button for 5 seconds to exit the Standard Pressure Setting mode.Hold down the set button of the monitor for 5 seconds to enter into the setting mode, as the right graphic shows. press“ ”or “ ”button to set the required pressure,and then quickly press the SET button to scroll through to the next the tyre and repeat this sequence to set the remaining tyres. Examination of the Tyre Condition The monitor indicates " --- " when a specific sensor's alignment is lost from the monitor, as graphic A shows. refer to Tyre Alignment Mode on page 3 to realign sensor.The monitor will indicate the " noS " signal whenever a sensor is either out of range or may be faulty,as graphic B shows.Installation of the MonitorThe monitor can be mounted using the pedestal or brackets supplied. The monitor can be fixed to a suitable surface in the vehicle, sun visor, dashboard etc. It has a build-in lithium battery or you may wish to use a power source from within the vehicle’s power socket to charge or operate the monitor.
TYRE GUARD5TYRE GUARD6Battery Capacity Indicator of the Monitor and SensorWhen the monitor is low on power, the battery icon and “MONITOR” icon on the screen flash, the buzzer gives a 10 second intermittent alarm. The monitor then sounds every 30 seconds within 5 minutes of total discharge. Note: Please keep the monitor in a cool environment when charging.A BmonitorSensor battery replacementReplace the corresponding sensor’s battery when the monitor indicates a low battery. Unscrew the plastic cap from the sensor, take out the battery and replace with a new button cell battery, (CR 1632). Ensure the “+” terminal is touching the upper bracket. Screw down the cover. Please refer to the right graphic A, B and CNote: 1. The battery model required for the sensors is a CR1632 button battery.2. The “+” and “-” pole of sensor battery must be placed in the correct position with the “+” terminal facing up; failure to do so may cause the sensor to burn out.3. In order to make sure that the battery is replaced correctly, enter tyre alignment mode and delete the alignment of the respective sensor and realign it again.Power upQuickly press SET button to enter into the stand-by mode at the power off state.Note: Once the monitor is turned on, the information from all tyres can take up to 4 minutes to be received in normal conditions. When the sensors are in an area of strong interference or in very cold conditions, the monitor may not receive the signal. Pull out the monitor’s antenna to increase the strength of the signal.BATTERYABSENSOR SENSOR COPING“+” POLE OF BATTERYCWhen a tyre sensor has low power,the battery icon together with the corresponding tyre icon flash on the screen and a 10 second intermittent alarm will sound.If the power of any of the sensors becomes too low,please replace the corresponding battery immediately.Charging the MonitorThe built-in lithium battery of the monitor is re-chargeable. Please connect the 12/24V DC charger into the port at base of the monitor, and then insert the adapter plug into the port of the vehicle’s 12/24V DC accessory port. The vehicle’s battery power will charge the monitor when the power supply of the vehicle is turned on. It takes approximately 6 hours to fully charge the monitor.The battery icon flashes as shown in graphic A, B and C above.The monitor will sound an alarm when fully charged. Graphic C will disappear after 1 second.A B Cmonitor monitor monitor
7TYRE GUARD 8TYRE GUARD Power offHold down SET button for at least 8 seconds, and the monitor will automatically switch off. Please note: the system will first enter into the setting mode 5 seconds after holding down SET button, continue holding down the SET button for a further 3 seconds or more to power off the monitor.Note: Whether the monitor is turned on or off, the sensor is always in standby mode.Standby TimeThe monitor is installed with an intelligent 15 minutes suspension device. The monitor turns into suspension status to save the power after the vehicles is switched off for more than 15 minutes. Once the vehicle is started, the monitor automatically turns on and connects to the vehicle’s sensors.4 Warning ConditionsThe TPMS possesses the two functions, monitoring tyre temperature and air pressure conditions of the vehicle’s tyres. .High Temperature WarningWhen the temperature inside the tyre exceeds 75°C, the system indicate the position of the tyre with abnormal temperature and its current temperature. Abnormal temperature is indicated by the flashing red LED on the monitor and the temperature icon flashing on the screen, as the right graphic shows.Low Air Pressure Warning: Level 1When the actual air pressure is equal to or falls below 85% of the set pressure the system will give an alarm and the monitor will indicate the position of the tyre with abnormal air pressure and its current air pressure. The low air pressure is indicated by the flashing red LED on the monitor and the pressure icon flashing on the screen, as the right graphic shows. will give a high temperature alarm and the monitor will
TYRE GUARD 910TYRE GUARD Low Air Pressure Warning: Level 2When the actual air pressure is equal to or falls below 75% of the set pressure the system will give an alarm and the monitor will indicate the position of the tyre with abnormal air pressure and its current air pressure. The low air pressure is indicated by the flashing red LED on the monitor and the pressure icon flashing on the screen, as the right graphic shows. Low Air Pressure Warning: Level 3When the actual air pressure is equal to or falls below 50% of the set pressure the system will give an alarm and the monitor will indicate the position of the tyre with abnormal air pressure and its current air pressure. The low air pressure is indicated by the flashing red LED on the monitor and the pressure icon flashing on the screen, as the right graphic shows. High Air Pressure WarningWhen the actual air pressure is equal to or greater than 120% of the set pressure the system will give an alarm and the monitor will indicate the position of the tyre with abnormal air pressure and its current air pressure. The high air pressure is indicated by the flashing red LED on the monitor and the pressure icon flashing on the screen, as the right graphic shows. Sensor Abnormality IndicationIf the monitor can’t receive the signal from the sensors within 20 minutes in standby mode, the alarm system will sound for 15 seconds The corresponding icon of the abnormal sensor will also flash “no S” which indicates there is either a fault with sensor is damaged or the sensor is out of range. ExplanationThe monitor will give out a continuous alarm for 15 seconds with the flashing red LED and back lights for 5 minutes along with the corresponding faulty tyre icon flashing. Press the “” or “ ” button to stop this alarm. Shortly after, the back light will automatically go off. The system alarm will sound again after one hour to further remind the operator.When a sensor is removed to inflate or deflate a tyre, this will cause the sensor to detect rapid and/or slow leakage because the sensor has suddenly detected zero pressure. The monitor will return to normal and the alarm will stop after the sensor is refitted. and indicate with the sensor, the
11TYRE GUARD 12TYRE GUARD 5 Technical SpecificationsSensorWorking Temperature 14 F TO 185 F (-10°C -- 85°C)Working Humidity 0 -- 95%Dimension 24 x 21 x 21mmWeight 11g(±1g) Battery Voltage 3V DC (CR1632)Battery Life 1 yearStandby Current 500nAWorking Current 6mAPressure Measure Range 0 psi -- 72.5 psi(0 bar– 5 bar)Pressure Measure Precision ± . psi(±1 5 0.1 bar)Temperature Measure Range 14 F TO 185 F (-10°C -- 85°C)Temperature Measure Precision ±3°CSignal Transmitting Frequency 433.92 MHzOperating Distance 8.0 metresMonitorWorking Voltage 3V DCWorking Temperature -4 F TO 140 F ( )-20°C -- 60°CWorking Humidity 0 -- 90% Standby Current 0.1mAWorking Current 15 mADimensionMonitor size：82mm×55mm×23mm (JET-M-300C)Monitor size：87mm×55mm×20mm (JET-M1-300C)Monitor size：82mm×52.5mm×16.5mm (JET-M2-300C)Signal Receiving Frequency 433.92 MHzColor of Backlight White6 TPMS AssemblyDescription QuantitySensorsMonitor One (1)Bracket One (1)One (1)Sensor anti-theft security devices Four(4)Hexagon Screw Twenty(20)Hexagon Allen Key Two (2) NOTE1. This system can efficiently monitor the air pressure and temperature of the vehicle’s tyres. 2. In order to avoid damage to this equipment, please do not attempt to disassemble any assembly.3. Your has an automatic monitoring function, so there is no TPMS need to press “ ” or “ ” to read the information.4. Please contact Shenzhen Jetson Electronic Technologies Co., Ltd. E-mail:zx@tesee.com.cn or log on to our website www.tesee.com.cn should you require further information.。 。。 。。 。User Manual One (1) bookFour (4)12/24 V DC Cigarette Lighter AdapterCR 1632 Battery Four(4)
FCC Information and Copyright This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC ID Label TIRE PRESSURE SENSOR Model NO.：JET-TMT-02 JETSON Battery: 3.0V FCC ID: 2AAU3JET-TMT-02 Shenzhen Jetson Electronic Technologies Co.,Ltd Made in China This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
13TYRE GUARD 14TYRE GUARD For customer reservation Name: Model No.: Date of Purchase: Place of Purchase: Note: 1. We offer one-year warranty and free repair services for the products from the date of purchase. 2. We offer lifetime maintenance services for our products. 3 . O u r w a r r an t y e x c l ud e s t h e no r m a l a b r a si o n o f a ny subassemblies and accessories, any damages from improper use, ac ci de nt s an d d is ma n tl em en t, an d t he d am ag es o f a ny accessories. 4. Please keep this part and the commercial invoice as the guarantee for the repair and examination of the products during warranty. Distributor: (Signature and seal)(This guarantee card will become effective upon the seal of the distributor.) Thank you for choosing our products.Please carefully fill in the following form.Name:Post Code: Address: Model No.: Tel: Invoice No.: Date of Purchase:Name of the Distributor: What makes you choose our products?□Economy □Service □Advert □Other□Quality □Website □Recommendation from friends Please fill in this card and send it back to our after service department. It will be the main guarantee for your right to gain the after services during the warranty.

Navigation menu