Jiangmen Dascom Computer Peripherals DL2101 Label & Barcode Printer User Manual Tally Dascom DT 210 230
Jiangmen Dascom Computer Peripherals Co.,Ltd. Label & Barcode Printer Tally Dascom DT 210 230
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3171843 |
| Application ID | 35knDMlzZNFp+pVgkg0Obg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 412.03kB (5150424 bits) |
| Date Submitted | 2016-10-24 00:00:00 |
| Date Available | 2016-10-24 00:00:00 |
| Creation Date | 2016-10-21 11:52:17 |
| Producing Software | Microsoft® Word 2010 |
| Document Lastmod | 2016-10-21 13:57:21 |
| Document Title | Tally Dascom DT-210/230 |
| Document Creator | Microsoft® Word 2010 |
| Document Author: | WORK |
User Manual DL-210 Label & Barcode Printer
Tally Dascom DL-210
User Guide V1.3
Important Safety Instructions (English)
Read the following instructions thoroughly before starting up your printer.
•
The device and mains-socket must all times be easily accessible.
•
Never carry out maintenance or repair work yourself. Always contact a qualified service
technician.
•
Keep this user guide in a place which is easily accessible at all times.
•
Place the printer on a solid and even base so that it cannot fall.
•
Never place the printer in the vicinity of inflammable gas or explosive substances.
•
Ensure the printer is connected to a socket with the correct voltage.
•
Always disconnect the printer from the power before opening the device to perform
maintenance work or remedy errors.
•
Do not expose the printer to high temperatures, direct sunlight or dust.
•
Keep all liquids away from the printer.
•
Protect the printer from shock, impact and vibration.
•
Make sure that both the printer and the computer is switched off before connecting the data
cable.
•
The print head will become very hot during printing; avoid contact with the print head after
printing has finished.
•
Do not perform any operation or action in any way other than those provided in this manual.
When in doubt, contact your dealer or your customer support.
Tally Dascom DL-210
User Guide V1.3
Wichtige Sicherheitshinweise (German)
Lesen Sie bitte diese Sicherheitshinweise durch, bevor Sie den Drucker in Betrieb nehmen.
Das Gerät und die Netzsteckdose müssen jeder Zeit leicht zugänglich sein.
Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie
immer einen qualifizierten Servicetechniker.
Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf.
Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen
kann.
Stellen Sie den Drucker keinesfalls in der Nähe von leicht entzündlichen Gasen oder explosiven
Stoffen auf.
Den Drucker nur an eine Steckdose mit der richtigen Spannung anschließen.
Wenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den
Netzstecker an der Steckdose ziehen.
Den Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen.
Keine Flüssigkeiten mit dem Drucker in Berührung bringen.
Den Drucker keinen Erschütterungen, Stößen oder Vibrationen aussetzen.
Sicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel
angeschlossen wird.
Der Druckkopf wird während des Druckens heiß. Vor dem Berühren deshalb einige Zeit abkühlen
lassen.
Weichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation
ab. Bei Unklarheiten wenden Sie sich bitte an Ihren Händler oder Ihren Kundendienst.
II
Tally Dascom DL-210
User Guide V1.3
Consignes importantes de sécurité (French)
Lire attentivement les instructions suivantes avant de mettre l’imprimante en service.
Le dispositif et la prise principale doivent toujours être accessibles facilement.
Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un
dépanneur qualifié.
Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber.
Ne jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de
substances explosives.
Ne connecter l’imprimante à une prise que lorsque la tension est correcte.
Pour déconnecter l’imprimante de l’alimentation principale, mettre l’imprimante hors tension et
toujours débrancher le connecteur secteur de la prise murale.
Ne pas exposer l’imprimante à des températures élevées, à la lumière directe du soleil ou à la
poussière.
Ne pas mettre l’imprimante en contact avec des liquides.
Ne pas exposer l’imprimante à des chocs, impacts ou vibrations.
S’assurer que l’imprimante et l’ordinateur sont hors tension avant de connecter le câble de
données.
La tête d’impression est brûlante pendant l’impression. C’est pourquoi laissez-la refroidir
quelques instants avant d’y toucher.
N'exécutez aucune opération ni action d'une autre manière que celle indiquée dans ce manuel.
En cas de doute, veuillez contacter votre distributeur ou service après-vente.
III
Tally Dascom DL-210
User Guide V1.3
Indicazioni di sicurezza importanti (Italian)
Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni.
Il dispositivo e la presa di corrente devono essere sempre facilmente accessibili.
Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un
tecnico di assistenza qualificato.
Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile.
Collocare la stampante su una superficie stabile, per evitare che cada a terra.
Non collocare la stampante in prossimità di gas facilmente infiammabili o di sostanze esplosive.
Collegare la stampante a una presa di corrente con tensione adeguata.
Per scollegare la stampante dalla rete di alimentazione, spegnere la stampante e disinserire
sempre il connettore di rete dalla presa.
Non esporre la stampante ad elevate temperature né alla luce solare diretta e alla polvere.
Evitare il contatto della stampante con liquidi.
Non esporre la stampante a colpi, scosse o vibrazioni.
Verificare che la stampante e il computer siano spenti prima di collegare il cavo di trasmissione
dati.
Durante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessario
opportuno quindi lasciarla raffreddare qualche istante.
Non eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale.
In caso di dubbio, contattare il rivenditore o dalla società incaricata dell’assistenza.
IV
Tally Dascom DL-210
User Guide V1.3
Instrucciones de seguridad importantes (Spanish)
Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio.
El dispositivo y la toma de corriente deben estar ubicados de forma que sea fácil acceder a ellos.
Nunca lleve a cabo trabajos de mantenimiento o reparación Ud. mismo, sino consulte a un
técnico de servicio calificado.
Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento.
Ponga la impresora sobre un base estable de manera que no pueda caer al suelo.
Nunca coloque la impresora en la vecindad de gases de fácil inflamabilidad o sunstancias
explosivas.
Asegure conectar la impresora sólo a un enchufe con un voltaje correcto.
Cuando quiera desconectar la impresora de la red, apague la impresora y siempre tire la clavija
de alimentación del enchufe.
No exponga la impresora a temperaturas altas, a la luz solar directa y al polvo.
No ponga la impresora en contacto con fluidos.
Nunca exponga la impresora a sacudidas, choques o vibraciones.
Asegúrese de que la impresora y el ordenador estén apagdos antes de conectar el cable de
datos.
La cabeza de impresión se pone muy caliente durante la impresión. Por lo tanto, deje enfriarlo
algún tiempo antes de tocarla.
No permita que se realice cualquier operación o acción de una forma diferente a lo que se señala
en el manual. En caso de duda, póngase en contacto con su comerciante o con su servicio
post-venta.
Tally Dascom DL-210
User Guide V1.3
Правила по технике безопасности. (Russian)
Прочитайте, пожалуйста, инструкцию по технике безопасности перед включением в работу
принтера.
Устройство и розетка должны быть всегда легко доступна.
Не выполняйте технические работы и ремонт техники самостоятельно, но сообщайте о
неисправностях квалифицированным сервисным техникам.
Данная инструкция должна быть всегда доступна каждому пользователю.
Установите принтер на ровном и стабильном месте так, чтобы он не смог упасть на пол.
Ни в коем случае не ставьте принтер вблизи легко воспламеняющихся газов и взрывчатых
веществ.
Включайте принтер в розетку только с соответствующим
Если Вы хотите отключить принтер от напряжения, сначала выключите принтер сам и затем
выньте штекер из розетки.
Берегите принтер от нагревания, от попадания на него прямых солнечных лучей и пыли.
Не допускайте попадания жидкости на принтер.
Нельзя подвергать принтер тряске, ударам и вибрации.
Убедитесь, что принтер и компьютер выключены, только после этого соедините принтер с
компьютером.
Печатающая головка нагревается во время работы принтера. Поэтому подождите какое-то
время, прежде чем дотронуться до нее.
Пользуйтесь принтером так, как это написано в документации. Если у Вас возникают
неясности, обращайтесь с вопросами к Вашим продавцам или в сервисный центр.
VI
напряжением.
Tally Dascom DL-210
User Guide V1.3
Instruções Importantes sobre Segurança (Portuguese)
Leia as instruções de segurança antes de usar a impressora.
A impressora e a tomada devem ser facilmente em todos os momentos acessíveis.
Consulte sempre um técnico qualificado para executar uma reparação .
Coloque a impressora sobre uma base sólida e nivelada, para que ela não sofra quedas.
Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias
explosivas.
Assegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada.
Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da tomada.
Não exponha a impressora a temperaturas altas ou luz solar direta.
Não aproxime substâncias líquidas da impressora.
Proteja a impressora de choques, impactos e vibrações.
Desligue a impressora e o computador antes de conectar o cabo da rede.
A cabeça da impressora pode ficar muito quente . Portanto, espere algum tempo antes de
tocá-la.
Não faça nenhuma operação ou ação além das recomendadas neste manual. Em caso de dúvida,
contate seu revendedor ou companhia de serviço.
VII
Tally Dascom DL-210
User Guide V1.3
Önemli Güvenlik Talimatları (Turkish)
Lütfen, yazıcıyı işletime geçirmeden önce bu güvenlik talimatlarını bütünüyle dikkatle okuyun.
Cihaz ve elektrik prizinin her zaman kolayca erişilebilir olması gerekir.
Bakım ve tamir çalışmalarını kesinlikle ve hiçbir surette kendi başınıza yapmayın; her zaman
kalifiye bir uzman servis-teknisyenine haber verin.
Yazıcıyı, üzerinden yere düşmesi mümkün olmayacak sabit ve düz bir zemine yerleştirin.
Yazıcıyı kesinlikle ve hiçbir surette kolayca yanabilecek gaz veya patlayıcı maddeler içeren
nesnelerin yakınına koymayın.
Yazıcı akım kablosunu sadece doğru gerilime sahip bir prize takın.
Yazıcıyı şebeke ağından ayırmak istediğinizde, yazıcıyı kapatın ve ağ-fişini her zaman prizden
çıkartın.
Yazıcıyı ne yüksek ısılı ne de doğrudan güneş ışığına ve toza mâruz kalan mekânlarda bulundurun.
Yazıcı hiçbir sıvı maddeyle temasta olmamalıdır.
Yazıcı hiçbir sarsıntıya, darbeye veya titreşime mâruz kalmamalıdır.
Veri kablosu bağlanmadan önce hem yazıcının hem de bilgisayarın kapalı olduklarından emin
olmalısınız.
Yazıcının başı basma esnasında yüksek ısıya ulaşıyor. Bu yüzden lütfen dokunmadan önce kısa
süre soğumasını bekleyin.
Yazıcının işletimi ve kullanımında bu dokümantasyondaki talimatların hiç dışına çıkmayın. Sorunlu
görünen hususlarda lütfen imâlatçınıza veya müşteri hizmetleri servisinize başvurun.
VIII
Tally Dascom DL-210
User Guide V1.3
TRADEMARK ACKNOWLEDGEMENTS
“IBM” is a trademark of International Business Machines Corporation.
“EPSON” is a trademark of Epson America I
ncorporated.
“DEC” is a trademark of Digital Equipment Corporation.
“Centronics” is a trademark of Centronics Data Computer Corporation.
“DOS” is a trademark of Microsoft Corporation.
“SAP” is a trademark of SAP AG.
“Windows”, “Windows 7”,”Windows 8”, “Windows 95”, “Windows 98“, “Windows NT”, “Windows
2000”, “Windows 2003/2008/2012/2012R2 Server”, “Windows XP” and “Windows Vista” are
trademarks of Microsoft Corporation.
All other product names and company names appearing in this manual are the registered
trademarks or trademarks of the individual companies.
IX
Tally Dascom DL-210
User Guide V1.3
About This Manual
This manual provides information to operators of the DL-210 to describe basic operations to enable safe and
correct use of the printer.
Symbols Description
The symbols in this manual are identified by their level of importance, as defined below. Read the following
carefully before handling the product.
CAUTION: Provides information that must be observed to prevent damage to the
equipment or loss of date.
NOTE: Advises you of information that is essential to complete a task.
Related Software and Documents
Related Software and Documents
Software/document name
Description
DL-210 User Manual
This manual.
DL-210 Maintenance Manual
This manual provides developer/ engineers
with all the necessary information.
Tally Dascom DL-210
User Guide V1.3
TABLE OF CONTENTS
About This Manual .................................................................................................................... X
1 INTRODUCTION ...................................................................................................................... 1
1.1 Features...................................................................................................................................... 1
1.2 Printer specification ................................................................................................................... 2
1.3 Print Media Types ...................................................................................................................... 3
1.4 External Dimension and Mass.................................................................................................... 5
1.5 Unpacking .................................................................................................................................. 6
1.6 Product Configuration ................................................................................................................ 8
1.7 Printer Components ................................................................................................................... 9
1.8 Control Panel ............................................................................................................................ 12
1.8.1 LEDs Behavior......................................................................................................................... 12
1.8.2 Feed Key Operation ................................................................................................................ 12
2 SETUP .................................................................................................................................... 13
2.1 Flow of Setup ........................................................................................................................... 13
2.2 Placing the Printer.................................................................................................................... 13
2.3 Attaching Power ....................................................................................................................... 14
2.4 Calibrate Sensor ....................................................................................................................... 15
2.4.1 Calibrate Gap Sensor ............................................................................................................ 15
2.4.2 Calibrate Reflective Sensor ................................................................................................... 15
2.5 Loading Roll Media................................................................................................................... 16
2.6 Loading Transfer Ribbon .......................................................................................................... 18
2.7 Connecting to Computer.......................................................................................................... 21
2.7.1 Connecting USB interface ...................................................................................................... 22
2.7.2 Connecting serial interface .................................................................................................... 22
2.7.3 Connecting parallel interface ................................................................................................. 23
2.7.4 Connecting Ethernet interface ............................................................................................... 23
2.7.5 Connecting Wlan Interface .................................................................................................... 24
3 NETWORK SETUP AND CONFIGURATION................................................................................. 25
3.1 Installing Driver............................................................................................................................. 25
3.2 Installing Setup Tool...................................................................................................................... 31
3.3 Setup Tool Application .................................................................................................................. 35
3.3.1 Model and Interface Setting .................................................................................................. 35
3.3.2 Configuring Printer ................................................................................................................. 36
3.4 LAN Interface Setup ...................................................................................................................... 38
3.5 Update Firmware .......................................................................................................................... 42
4 SETTING/CHECKING MODES ................................................................................................... 44
4.1 Print a Parameter Setting Page (Self-test Page) ........................................................................... 44
4.2 Hexadecimal Dumping Mode ....................................................................................................... 46
4.3 Auto Calibrate Label ..................................................................................................................... 47
5 TROUBLESHOOTING AND MAINTENANCE ............................................................................... 48
5.1 Common Issues ............................................................................................................................ 48
Tally Dascom DL-210
User Guide V1.3
5.2 Resetting the Factory Default Values ........................................................................................... 49
5.3 Removing Jammed Label .............................................................................................................. 49
5.4 Cleaning Thermal Print Head ........................................................................................................ 50
5.5 Maintenance................................................................................................................................. 50
6 COMMUNICATION INTERFACES SPECIFICATIONS ..................................................................... 51
6.1 USB interface ................................................................................................................................ 51
6.2 Wi-Fi interface .............................................................................................................................. 51
6.4 Ethernet interface......................................................................................................................... 51
6.5 Serial interface .............................................................................................................................. 52
6.6 Parallel interface ........................................................................................................................... 53
6.7 Power Supply ................................................................................................................................ 54
7 CHARACTER CODE PAGES ....................................................................................................... 55
7.1 Common to all pages (International Character Set: USA) ............................................................ 55
7.2 International Character Sets ......................................................................................................... 56
7.3 [User-defined page] ...................................................................................................................... 57
7.4 [PC437: USA, Standard Europe] .................................................................................................... 58
7.5 [PC850: Multilingual] .................................................................................................................... 59
7.6 [PC852: Latin2] ............................................................................................................................. 60
7.7 [PC858: Euro] ................................................................................................................................ 61
7.8 [PC860: Portuguese] ..................................................................................................................... 62
7.9 [PC863: Canadian-French] ............................................................................................................ 63
7.10 [PC865: Nordic]........................................................................................................................... 64
7.11 [PC866: Cyrillic #2] ...................................................................................................................... 65
7.12 [PC720: Arabic] ........................................................................................................................... 66
8 COMMAND SETS .................................................................................................................... 67
8.1 ESC/POS Command Sets ............................................................................................................... 67
8.2 ZPL Command Sets ....................................................................................................................... 69
8.3 EPL Command Sets ....................................................................................................................... 75
Appendix: Installing the Cutter .................................................................................................. 76
Removing the Tear Bar ....................................................................................................................... 76
Installing the Auto Cutter ................................................................................................................... 77
Appendix: FCC STATEMENT ........................................................................................................ 80
Appendix: DASCOM REPRESENTATIVES ...................................................................................... 81
Tally Dascom DL-210
User Guide V1.3
1 INTRODUCTION
The Dascom® DL-210 model is the best value in a desktop thermal printer. The DL-210 printer
provides thermal transfer and direct thermal printing at speeds up to 6 ips (inches per second) at a
203 dpi (dots per inch) print density.
1.1
Features
• Easy to switch printer language between ZPL, EPL and TSC programming and label formats.
• Easy operation. With open structure users can easily change paper roll and ribbon.
• Large media compartment. Ribbon as long as 300m and paper roll of Max. OD φ127mm can be
used. Therefore users can change the ribbon and paper roll less often so as to work more efficiently.
•Wide range of connectivity. The USB interface is standard interface. Serial/parallel/Ethernet/ Wi-Fi
are optional interfaces. Various interface choices suit all needs.
The DL-210 printers offer these basic printer options:
• Auto cutter.
This user guide provides all the information you need to operate your printer on a daily basis.
Tally Dascom DL-210
1.2
User Guide V1.3
Printer specification
Print
Parameter
Print method
Print width
Print speed
Print head
Resolution
Chinese
Alphanumeric
User-defined
Fonts
Code Pages
Scalable/Rotation
Graphics
1D
Direct thermal/Thermal transfer printing
108mm
6IPS
Dot pitch: 0.125mm
203DPIx203DPI
GB18030 24×24 (Simplified/Traditional Chinese)
Resident single byte (ZPL): Font A, Font B, Font D, Font E, Font F, Font G, Font
H, Font V0, Font GS, Font P, Font Q, Font R, Font S, Font T, Font U, Font V
User-defined fonts can be downloaded into FLASH, SDRAM.
EPL:
PC437;PC850;PC852;PC860;PC863;PC865;PC857;PC861;PC862;PC855;PC866;
PC737;PC851;PC869;Windows 1252;Windows 1250;Windows 1251; Windows
1253;Windows 1254;Windows 1255
ZPL:
PC850, windows 1250, windows 1252, windows 1251, windows 1253,
windows 1254, windows 1256
Zoom in 1~8 times in vertical or horizontal, rotate by 00, 900, 1800, 2700.
Graphics (Monochrome PCX, BMP) can be downloaded into SDRAM.
ZPL:
Code11;Interleaved 2 of 5;Code 39;Code 49;Planet Code;
EAN-8;EAN-13;UPC-E;UPC-A;Code 93;Code 128;
Industrial 2 of 5;Standard 2 of 5;Codabar;MSI;Plessey
EPL:
EAN-8;EAN-13;UPC-E;UPC-A;Code 39;Code 93;Code 128; Interleaved 2 of 5
ZPL:
PDF417;CODABLOCK;Maxicode;Aztec;QR Code; Data Matrix;
Barcodes
2D
Ribbon
ID
OD
Length
Width
Media Spec.
Media
Handling
Media cut
Media type
Control Panel
Detect
Function
Emulation
Key
LED indicator
Standard sensors
Optional kit sensor
Zebra, EPSON
EPL:
PDF417;Maxicode;QR Code; Data Matrix;
φ25.4mm
φ68mm
300m
33~110mm
Thickness 0.06~0.18mm
Width 25~118mm
Length 8.9~400mm
Max. OD ∮127mm
Min. ID φ25.4/38.1mm
Tear bar, auto-cutter, peeler
Roll paper, fold paper
(continuous, non-continuous, continuous tag, wrist-band, normal media and
all sorts of receipts )
One key: Feed
Three LEDs: Power, Error, Status (Paper out/Ribbon out)
Black mark sensor, Media sensor, Ribbon sensor, Machinery sensor
Label taken sensor
ZPL, EPL, TSC
Tally Dascom DL-210
Power Supply
Memory
Interface
Input
Output
SDRAM
FLASH
Standard
Optional
Software
Physical Spec.
Safety
Standard
Dimensions
Casing Color
Weight
Operating
condition
Storage condition
Safety
EMC
Certificate
Optional kit
Reliability
1.3
TPH lifetime
User Guide V1.3
External power adapter
AC 100V-240V, 50-60Hz
24V DC, 3A
8MB
8MB
USB (2.0 Full-Speed)
Serial (RS-232, DB25)
Parallel Centronics (IEEE-1284)
Ethernet: 10M/100M
Wi-Fi (802.11b/g)
Driver (Windows 32bit/64bit), Bartender, SDK system
230(W)×290(D)×176(H)mm
Black
Approx 3kg
5～40℃/20～95%RH (non-condensing)
-20～60℃/≤95%RH (non-condensing)
UL, CE, FCC, CCC
Class B
CCC, CE, FCC, UL, Energy star
Cutter, Peeler
150km
(Condition: use specific thermal roll paper and the print rate is 12%)
Print Media Types
Important •Dascom strongly recommends the use of Dascom-brand supplies for
continuous high-quality printing.
Your printer can use various types of media:
• Standard media—Most standard (non-continuous) media uses an adhesive backing that sticks
individual labels or a continuous length of labels to a liner.
• Continuous roll media—Most continuous roll media is direct thermal media (similar to FAX paper)
and is used for receipt or ticket style printing.
• Linerless media—Linerless labels have an adhesive backing, but they are wound onto a core
without a liner. The media typically is perforated and may have black marks on the bottom surface of
the media to indicate label separations. The top surface of linerless media labels have a special
coating that keeps the labels from sticking to each other. The printer must be equipped with a
special Linerless option to be able to use linerless media to keep the media from sticking to the
printer.
• Tag stock—Tags are usually made from a heavy paper (up to 0.0075in./0.19mm thick). Tag stock
does not have adhesive or a liner, and it is typically perforated between tags.
For more information on basic media types, see the following table.
The printer typically uses roll media, but you can use fan-fold or other continuous media too. Use the
correct media for the type of printing you require. You must use direct thermal media. When
printing without a ribbon, you must use direct thermal media. When using ribbon, you must use
thermal transfer media.
Media Type
How it looks
Description
Tally Dascom DL-210
Non-Continuous
Roll Media
User Guide V1.3
Roll media is wound on a core that can be 0.5 to 1.5
in. (12.7 to 38.1 mm) in diameter. Labels have
adhesive backing that sticks them to a liner, and
they are separated by gaps, holes, notches, or black
marks. Tags are separated by perforations.
Individual labels
are separated by one or more of the following
methods:
• Web media separates labels by gaps, holes, or
notches.
• Black mark media uses pre-printed black marks on
the back side of the media to indicate label
separations.
• Perforated media has perforations that allow the
labels or tags to be separated from each other
easily. The media may also have black marks or
other separations between labels or tags.
Non-Continuous
Fanfold Media
Fan-Fold media is folded in a zigzag pattern. Fanfold
media can have the same label separations as
non-continuous roll media.
The separations would fall on or near the folds.
Continuous Roll
Media
Roll media is wound on a core that can be 0.5 to 1.5
in. (12.7 to 38.1 mm) in diameter. Continuous roll
media does not have gaps, holes, notches, or black
marks to indicate label separations. This allows the
image to be printed anywhere on the label. A cutter
can be used to cut apart individual labels. With
continuous media, use the transmissive (gap)
sensor so the printer can detect when the media
runs out.
Tally Dascom DL-210
1.4
User Guide V1.3
External Dimension and Mass
Width: Approximately 230 mm
Depth: Approximately 290 mm
Height: Approximately 179.5 mm
Mass: Approx. 3 kg (excluding power adapter)
Front View
Back view
Side view
Tally Dascom DL-210
1.5
User Guide V1.3
Unpacking
When you receive the printer, please check for possible shipping damage:
1. Inspect the outside of both the box and the printer for possible damage.
2. Open the top cover of the printer to see if the media compartments are in order.
If you discover shipping damage upon inspection:
Immediately notify the shipping company and file a damage report.
Keep all packaging material for shipping company inspection.
Notify your authorized Tally Dascom reseller.
DL-210 printer
Ribbon
Power cord
Media
CD-ROM
Power Adapter
Ribbon Rewind Paper Core
The package contents vary with different customized order requirements.
Tally Dascom DL-210
User Guide V1.3
Package Contents:
Standard
Optional
Printer
1 unit
Ribbon rewind paper core
1 piece
Ribbon sample
1 piece
Ribbon spindle
2 pieces
Media sample
1 piece
Media fixer
2 pieces
Media spindle
1 piece
Power adapter
1 piece
Power cord
1 piece
Graphic installation guide
1 piece
CD-ROM
1 piece
Peeler
1 set
Cutter
1 set
Wax
Thermal transfer
EU/UK/US
Including user guide, Driver, setup
tool, graphic installation guide
Tally Dascom DL-210
1.6
User Guide V1.3
Product Configuration
Interface Types
Optional Interface
(Serial/ Parallel/
Ethernet/
Wi-Fi）
USB interface
USB interface (USB2.0, Full speed)
Serial interface: Serial port (RS-232, DB25)
Parallel interface: Bidirectional parallel port (IEEE1284)
LAN interface: Ethernet (10Base-T, 100Base-TX)
Wireless LAN interface: Wi-Fi (802.11b/g)
Interfaces
Power
Cord
Model
DL-210
Paper Cut
Sensor
USB
PAR
SER
ETH
Wi-Fi
EN/UK/EU
Cutter
Tear
Bar
Black
Mark
√
√
√
√
Remarks: “√” indicates standard configuration, “O” indicates optional configuration.
PAR=Parallel interface; SER= Serial interface; ETH=Ethernet interface.
Tally Dascom DL-210
1.7
User Guide V1.3
Printer Components
Printer components and their functions are shown as below:
Media Window
Top Cover
Control Panel
Optional Interface
(Serial/ Parallel/
Ethernet/
Wi-Fi）
Power Switch
Power Socket
USB interface
Component Name
Function
Media window
Monitor the media status via this window
Top cover
Open this cover for loading ribbon and media
Control Panel
Power LED
Indicate the power status
Status LED
Indicate the status of media, ribbon and label-taken
Error LED
Indicate print head temperature and Print head
mechanism open or not
Feed key
Press this key for feeding media
Power socket
Connect power cord to the printer
Power switch
For switching on/off printer
USB interface
Connect USB interface cable from host
Optional interface
(Serial/ Parallel/ Ethernet/ Wi-Fi)
Connect optional interface cable from host
(interface type is on request)
Tally Dascom DL-210
User Guide V1.3
Ribbon Pick-up Holder
Print Head Mechanism
Ribbon Holder
Media Holder
Print Head Locking
Button
Print Head Locking
Button
Print Head
Ribbon Pick-up
Holder
Tear Bar
Rotatable Board
Component Name
Print Head Ribbon Holder
Mechanism Print Head
Ribbon Pick-up Holder
Media Holder
Print Head Locking Button
Function
For placing ribbon, lower seat for new ribbon, top seat for used ribbon.
Heat the ribbon and transfer imaging components to the media
Turn the adjustor for stretching ribbon
For placing media
For closing or opening the print head mechanism
Tear Bar
For tearing the media
Rotatable Board
Disassemble the rotatable board for installing optional kit: peeler or
cutter
10
Tally Dascom DL-210
User Guide V1.3
Media Guide
Media Guide
Adjuster
Black Mark Sensor
Platen Roller
Component Name
Media Guide
Media Guide Adjustor
Black Mark Sensor
Platen Roller
Function
Align the media in the center of media path
Adjust the space between the two media guides
For detecting black mark. The sensor position can be adjusted
according to the black mark position.
For feeding paper
Ribbon
Rewind
Paper Core
Media Fixer
Ribbon Spindle
Media Spindle
Component Name
Media Spindle
Media Fixer
Ribbon Spindle
Ribbon Rewind Paper Core
Function
Insert it into media core for supporting media
For fixing media (as the above figure shown)
Install it in ribbon holder for supporting ribbon or ribbon
rewind pipe
Stick the used end of ribbon to the pipe, rewind ribbon while
the pipe is turning
11
Tally Dascom DL-210
1.8
User Guide V1.3
Control Panel
1.8.1 LEDs Behavior
LEDs
Power
Status
LEDs’ behavior
Status
On ○
Power on.
Off ●
Error or power off.
On ○
Paper end.
Off ●
Normal.
Fast blink
Error
○●○●○●○
Label remains in peeler.
Slow blink ○●●○●●○
Ribbon end.
On ○
Print head mechanism is opened.
Off ●
Normal.
Fast blink
○●○●○●○
Print head is over-heated.
1.8.2 Feed Key Operation
Feed Paper
Under ZPL/EPL mode, press Feed Key once, feed one piece of label;
Under ZPL/EPL mode, hold down Feed Key without release, feed labels continuously.
12
Tally Dascom DL-210
User Guide V1.3
2 SETUP
1.1
Flow of Setup
This chapter consists of the following sections along with the setup flow of the product and
peripherals.
1. Placing the Printer (page 13)
2. Adjusting Sensor (page 15)
3. Loading Paper Roll (page 16)
(page
4. Loading Ribbon (optional) (page 18)
(page
5. Attaching Power (page 14)
6. Printing Self-test (page 42)
7. Connecting the Printer to the Host Computer (page 23)
2.1 Placing the Printer
You can install this printer horizontally. Place the printer on a solid, flat, stable surface; ensure the
printer is placed in a stable position and there is easy access for users to the control panel and roll
paper holder. Also ensure there is enough space for sufficient ventilation and for the printout.
When selecting the placement position, be aware of the following advice:
Never place the printer near to any flammable gas or explosive substances.
Do not expose the printer to direct sunlight. If you cannot avoid placing the printer near a
window, protect it from the sunlight with a curtain.
When connecting a computer to the printer, make sure the maximum recommended cable
length is not exceeded.
Ensure sufficient distance between the printer and any heating devices or radiators.
Avoid exposing the printer to extreme temperature or air humidity fluctuations. Avoid exposure
to dusty environments.
It is recommended the printer is installed in a position which reduces noise exposure to the work
place during printing.
13
Tally Dascom DL-210
User Guide V1.3
2.2 Attaching Power
Checking the voltage of the power adapter
Before you connect the power adapter to the power socket check if the voltage is
correct. If you connect the power adapter to power with incorrect voltage this may
result in electrical damage to adapter and printer.
1. Make sure the printer and the computer are powered off.
2. Connect the power cord to the power adapter.
3. Connect the power adapter to the power supply interface at the rear of the
printer.
4. Ensure the power cord is securely connected. Connect the power cord plug to a
mains socket on the wall.
1) Please only use the power adapter are recommended by supplied or
equivalent products;
2) When disconnecting the AC adapter plug, handheld plug connector housing, to
avoid the pulling on the cable in force;
3) Avoid drag the power adapter cable, otherwise it will damage the cables,
causing fire and shock;
4) Avoid put power adapter around a heating device, otherwise the cable may
melt, causing fire and shock;
5) If you do not use the printer in a long time, disconnect the power supply of
printer power adapter.
14
Tally Dascom DL-210
User Guide V1.3
2.3 Calibrate Sensor
Gap sensor and reflective sensor should be calibrated separately.
First of all, please open the setup tool, enter “Printer Setup”, choose paper sensor: gap sensor by
default. You could switch to reflective sensor according to your need.
2.3.1 Calibrate Gap Sensor
(1) Make sure gap sensor is selected through the setup tool.
(2) Lift the top cover to expose the media holder and the print head mechanism.
(3) Move around the sensor support so as to align its triangle with another triangle on the center
housing. As it is shown below:
2.3.2 Calibrate Reflective Sensor
(1) Select Reflective Sensor in the setup tool.
(2) Lift the top cover to expose the media holder and the print head mechanism.
(3) Align the black mark sign with the black mark sensor.
Black Mark Sign
Black Mark Sensor
15
Tally Dascom DL-210
User Guide V1.3
Label
Black Mark Sign
liner
Lower Sensor
(4) Put the media between the media compartment and the tear bar. And then close the mechanism
and the top cover.
2.4 Loading Roll Media
Must use thermal media in case of no ribbon in the printer. If using ribbon, you
have to use thermal transfer media.
Tips for avoiding media jam: Make sure the media is aligned in the center of the
printer and the media fixers are firmly pressed against both sides of the roll.
Before printing, it is necessary to check whether the media you use is appropriate or not. You can
scratch the media surface, if the scratch turns black, it is direct thermal media. In this case, you do
not need to load ribbon. Otherwise, it is thermal transfer media, you have to use a ribbon.
(1) Lift the top cover to expose the media
holder and the print head mechanism.
(2) Load the media roll onto the spindle from
left to right.
(3) Put the fixers on and move from right to left
until they lean against the media.
(4) Click the media spindle back into the media
holder.
Print surface must be upward.
16
Tally Dascom DL-210
User Guide V1.3
(5) Unlatch the print head mechanism by
pushing the two blue locking buttons on the
sides toward the rear.
(6) Lead the media under the print head
mechanism through the media guides.
(7) Control the blue media guide adjustor so as
to align the media in the central path.
(8) Lead the media over the platen roller and
through the tear bar.
(9) Put the print head mechanism down and
press down firmly until you hear a snap.
(10) Close the top cover and turn on the
printer or press the “FEED” button if the
printer is already on.
(11) In order to make sure the data is printed within the label area, it is necessary to execute
Label Calibration: Hold down Feed Key and switch on printer simultaneously, release Feed
Key after the buzzer beeps twice. Then the label will be positioned automatically.
Label calibration should be executed in the following situations:
Use printer for printing label first time.
Replace different size of labels.
Printer skips labels
Printer feeds blank labels.
Refill with new roll of labels.
17
Tally Dascom DL-210
User Guide V1.3
2.5 Loading Transfer Ribbon
Transfer ribbons come in several varieties and in some cases colors to match your application needs.
The media and ribbon types should be matched to provide you with optimal print results. Always use
ribbon that is wider than the media to protect the printhead from wear.
For direct thermal printing, do not load ribbon in the printer.
Do not use ribbon while using direct thermal media. Otherwise, barcode
and graph will be distorted.
(1) Lift the top cover to expose the media holder
and the print head mechanism.
(2) Unlatch the print head mechanism by pushing
the two blue locking buttons on the sides toward
the rear.
(3) Unwrap the ribbon roll pack and separate the
ribbon roll and the bare paper core.
(4) Insert the spindles into the core and the ribbon
respectively.
(5) Attach the edge of the ribbon on the bare paper
core and wind it a little onto the core.
Do not rip the ribbon leader on
ribbon rewind pipe.
Do observe the direction of
hexagon.
18
Tally Dascom DL-210
User Guide V1.3
(6) Open the sensor support.
(7) Insert the ribbon roll into the ribbon holder
(lower seat of the print head mechanism): Insert
the hexagon end onto the ribbon adjustor (blue
gear), then insert the other end into the slot of the
ribbon holder.
(8) Turn back the print head mechanism and then
insert the ribbon rewind paper core into the
pick-up holder (top seat): Wind the ribbon through
print head, and insert the spindle hexagon end
onto the ribbon adjustor (blue gear), then insert
the other end into the slot of the pick-up holder.
Keep the brighter surface of
ribbon inside while winding the
print head.
19
Tally Dascom DL-210
User Guide V1.3
(9) Turn the wheel of the print head mechanism to
ensure the ribbon is tightly wound.
(10) Close the sensor support.
(11) Press down the print head mechanism on both
sides firmly until you hear a snap.
20
Tally Dascom DL-210
User Guide V1.3
2.6 Connecting to Computer
NOTE!
Be sure to install the driver before connecting the printer to the host computer.
Before installing, disconnect the Power Unit from the printer (as well as turning the power switch
off). Even when the power switch is off, voltage is still present at some points on the circuit board.
Changing components while the power unit is connected can cause damage to the interface board
and the printer.
Optional Interface
(Serial/ Parallel/
Ethernet/
Wi-Fi）
Power Switch
USB interface
Power Socket
Component Name
Function
Power socket
Connect power cord to the printer
Power switch
For switching on/off printer
USB interface
Connect USB interface cable from host
Optional interface
(Serial/ Parallel/ Ethernet/ Wi-Fi)
Connect optional interface cable from host
(interface type is on request)
Connection cable must comply with the following requirements:
Connection Type
USB
Serial
Parallel
Ethernet
Specifications
USB 1.1/2.0 compatible
RS232
IEEE 1284.4
10 Base-T/100 Base-TX compatible
21
Tally Dascom DL-210
User Guide V1.3
2.7.1 Connecting USB interface
CAUTION!
Be careful not to insert the USB interface cable into the cash drawer kick-out connector.
2.7.2 Connecting serial interface
WARNING!
Be sure to turn off the power supply for both the printer and host computer before
connecting the cables.
1. Insert the interface cable connector firmly into the interface connector on the
connector panel.
2. When using the connectors equipped with screws, tighten them to secure the
connectors firmly.
22
Tally Dascom DL-210
User Guide V1.3
3. When using interface cables equipped with a grounding line, attach the ground
line to the screw hole marked “FG” on the printer.
4. Connect the other end of the interface cable to the host computer.
2.7.3 Connecting parallel interface
1. Insert the interface cable connector firmly into the interface connector on the
connector panel.
2. Press down the clips on either side of the connector to lock it in place.
3. When using interface cables equipped with a grounding line, attach the ground
line to the screw hole marked “FG” on the printer.
4. Connect the other end of the interface cable to the host computer.
2.7.4 Connecting Ethernet interface
23
Tally Dascom DL-210
User Guide V1.3
Before installation, make you have installed the driver and the driver for Ethernet
interface (see Installing Driver on page 17)
When LAN cables are installed outdoors, make sure devices without proper surge
protection are cushioned by being connected through devices that do have surge
protection.
Otherwise, the devices can be damaged by lightning.
Never attempt to connect the customer display cable, drawer kick-out cable, or the
standard telephone line cable to the 10/100BASE-T LAN connector.
Connect the printer to a network by a LAN cable via a switch.
Connect a 10/100BASE-T cable to the 10/100BASE-T LAN connector by pressing firmly until the
connector clicks into place.
2.7.5 Connecting Wlan Interface
24
Tally Dascom DL-210
User Guide V1.3
3 NETWORK SETUP AND CONFIGURATION
3.1 Installing Driver
Switch off the printer before running the printer driver setup.
Your printer CD-ROM comes with Windows Driver. Go to the Driver folder and run the installer.
Please check the website www.dascom.com for the latest version of driver.
(1) Click “Next”.
25
Tally Dascom DL-210
User Guide V1.3
(3) Select the installation path to the Driver.
(3) Click “Finish”.
26
Tally Dascom DL-210
User Guide V1.3
(4) Click “Yes”.
(5) Click “Next”.
27
Tally Dascom DL-210
User Guide V1.3
(6) Choose interface.
(7) Choose printer model “Tally Dascom DL-210Z” or “Tally Dascom DL-210E”, and the installation
path. Then click “Next”.
28
Tally Dascom DL-210
User Guide V1.3
(8) Click “Next”.
(9) Enter printer name. Click “Next”.
29
Tally Dascom DL-210
User Guide V1.3
(10) Click “Finish”.
(11)Then the driver is installed successfully.
30
Tally Dascom DL-210
User Guide V1.3
3.2 Installing Setup Tool
Your printer CD-ROM comes with Tally Dascom Setup Tool. Go to the folder and run the installer.
Please check the website www.dascom.com for the latest version of setup tool.
(1) Choose setup language.
(2) Click next.
31
Tally Dascom DL-210
User Guide V1.3
(3) Select the installation path to the tool.
(4) Click “Finish”.
32
Tally Dascom DL-210
User Guide V1.3
(5) Click “Install”.
(6) Click “Install”.
33
Tally Dascom DL-210
User Guide V1.3
(7) Installation complete. Click “Finish”.
34
Tally Dascom DL-210
User Guide V1.3
3.3 Setup Tool Application
A CD comes along with printer. The CD contains POS & label printer setup tool for configuring printer.
Or, please find the latest setup tool on Dascom website: www.dascom.com
Read the help file carefully before using the setup tool. Please click “Help” button below for more
information.
3.3.1 Model and Interface Setting
Select the printer model and the suitable interface before configuring printer.
Click “setting” for setting serial interface or parallel interface. For serial interface and emulation
setting, the setting won’t be valid unless you restart the printer.
35
Tally Dascom DL-210
User Guide V1.3
3.3.2 Configuring Printer
After model and interface setting, select “Printer Setup” tab for configurations.
Setup Items Explanation
Setup Items
Options
Default
Page Mode
On, Off
On
Print Density
1, 2, 3, 4, 5, 6
Print Media
Label Paper,
Continuous Paper
Label
Paper
Printer Language
English, Chinese
English
Print Method
Thermal Transfer,
Direct Thermal
Thermal
Transfer
Set the printer’s system language, Chinese or
English.
Use ribbon select thermal transfer; Use thermal
paper select direct thermal
Peeler
Off, On
Off
Enable peeler or not
Print Speed
1, 2, 3, 4
Emulation
ESC/POS, ZPL,
EPL
ZPL
Cut Mode
Off, Full Cut,
Partial Cut
Off
Set the printer’s cutting mode.
Paper Out
Detection
On, Off
On
On: Detect the printer's paper is empty or not.
Off: Disable paper end detection.
Description
Use un-continuous paper set to on; Use continuous
paper set to off.
Adjust print density. Level 1 is lowest, Level 6 is
highest.
Select the actual media type.
Adjust the print speed. Level 1 is lowest, Level 4 is
highest.
Select ZPL/EPL while using un-continuous paper;
Select ESC/POS while using continuous paper.
36
Tally Dascom DL-210
User Guide V1.3
Print Position
Detection
On, Off
Off
Auto Calibrate
Label
On, Off
Off
Top Form Sensing
On. Off
Off
Paper Sensor
Selection
Gap sensor,
Reference sensor
Gap
sensor
Print Home Offset
User-defined
Cutting position
offset
User-defined
Black mark AD
value
User-defined
Enable print position detection or not
On: It will auto calibrate the label when you use a
different size/format of label.
Off: Disable auto calibrate label
Before the printer begins to detect the label length,
it will feed and print based on the printing data so
as to avoid unnecessary waste of media during
length detection.
Choose between the gap sensor and the reference
sensor.
Set the vertical distance between print home
position and the top of black mark. When the value
is positive, the media moves inward towards the
printer, and vice versa.
Range: -5~+5 (mm)
Set the vertical distance of the tearing position.
When the value is positive, the media moves inward
towards the printer, and vice versa.
Range: -5~+5 (mm)
Adjust the black mark detection accuracy.
Explanation for Buttons
Button
Description
When printer is powering on, click this button for acquiring the current setup menu. It
Get Printer Setting
will display on the screen.
Print Self-test
Click this button for printing current settings for the printer.
Restore All Setting
Click this button for restore to default setting.
Send Setting
Make the new settings effective.
Calibrate label
Click this button to calibrate label.
After setting, the printer will beep once, then the setting become valid.
In order to enhance print head lifetime, it is recommended that set the low print
density if the printing quality is acceptable.
37
Tally Dascom DL-210
User Guide V1.3
3.4 LAN Interface Setup
(1) Select Network interface in the setup tool. And then click “Setting”.
(2) Click “Setup Printer”.
38
Tally Dascom DL-210
User Guide V1.3
(3) You could change DHCP, IP address or other settings. And then enter OK.
(4) At the end, click OK to implement the change.
39
Tally Dascom DL-210
User Guide V1.3
3.5 WLAN Interface Setup
If your printer connected to the computer with Wireless Ethernet, there are two kinds of modes: AP
mode and STA mode.
AP means Access Point (AdHoc Mode). When the printer is working under AP mode, it works as
an access point to the cable network for the user.
STA means Station mode (Infra Structure Mode). When the printer is working under STA mode, it
works as a wireless terminal device. It is discoverable and choose access point.
We would suggest you use AP mode for your initial usage. Factory setting: AP mode, at the
convenience of users to change Wi-Fi parameters. Users can get access via setup tool to change
Wi-Fi parameters, such as IP address, network name, or switching to STA mode.
(1) Connect the PC to the printer with a USB cable. Turn on the printer.
Select USB interface in the setup tool. And then click “Wi-Fi Setup”.
40
Tally Dascom DL-210
User Guide V1.3
(2) You could change the working mode, SSID, DHCP, IP address or other settings. And then enter
Confirm to save the new setting.
41
Tally Dascom DL-210
User Guide V1.3
3.6 Update Firmware
Dascom is not liable if customers are doing a firmware update by themselves. If
power is switched off during the process, the printer may be damaged afterwards.
(1) Preparation
USB cable, 24V power adapter, DL-210 setup tool, firmware file.
(2) Connection
Connect printer and host with USB cable firmly. Check the Device Manager, if connection is
successful, “USB printing support” will display under “universal serial Bus Controllers” directory.
Otherwise, please check the connection between printer and USB interface, please check
whether the Driver installation is successful or not.
(3) Enter Update Mode
① Lift up top cover and turn up print head mechanism
Print head mechanism
42
Tally Dascom DL-210
User Guide V1.3
② Hold down Feed Key and switch on printer simultaneously. Release Feed Key once powering
on, the printer will beep once.
③ Status LED on, printer enter upgrade mode.
(4) Upgrade Firmware
① Run Dascom setup tool, select model Label Printer and USB interface.
② Select “Update Firmware” tab, then click “Browse” to locate the firmware/CG file, and then
click “Update”. May take about 20 seconds.
③ After loading the firmware, the Power LED, Error LED and Status LED blink.
④ When the printer beeps twice, and the three LEDs are on, turn the printer off.
⑤ Mission complete.
43
Tally Dascom DL-210
User Guide V1.3
4 SETTING/CHECKING MODES
Besides the ordinary print mode, the printer has the following modes to set or to check
settings of the printer.
Self-test Mode
Hexadecimal Dumping Mode
4.1 Print a Parameter Setting Page (Self-test Page)
Before you connect the printer to the computer, make sure that the printer is in proper
working order.
You can do this by printing a configuration status label.
1. Make sure the media is properly loaded, the top cover of the printer is closed and the
printer is power off. Then, press and hold the Feed button once you are ready.
2. Hold down Feed Key and then switch on printer till Power LED blinks once, buzzer beeps
once.
3. The printer will print out a parameter setting page.
44
Tally Dascom DL-210
User Guide V1.3
Here is the self-test status page and its explanation. The printout is an example. It may differ
depending of installed options or interfaces:
Parameter settings
Model
DL-210
SN NO
XXXXXXXXXXXX
ID NO
28.904.XX
Firmware version...........................40.XX.XX
Interface....................................USB+Parallel
Serial interface…..9600bps 8bitD/1bits/None
Emulation..............................................ZPLII
Media.....................................................Label
Print Type................................Direct Thermal
Print Sensor……………………..……Reflect
Print count..................................................0m
Label size…………………….……100.0mm
Gap size………………………………2.0mm
Sensor AD…….G3 D_300 B_0 1.09V 0.28V
Memory................................................8192K
Print Density..................................................2
Peeler.........................................................Off
Black Mark................................................Off
Cutter..........................................................On
Cut mode…………………..…………full cut
Home position adjust……………….…0 mm
Tear position adjust…...…………….…0 mm
Paper end detection....................................On
Auto Calibrate Label.................................Off
Print Position Detection.............................Off
Page mode..................................................On
Print Speed.......................................150mm/s
Print Width........................108mm (8dot.mm)
Model
Serial Number
ID Number
F/W
Interface type
Serial setting
Emulation type
Media info and
Printing method
Current memory size
Density
Peeler status
Black mark status
Cutter status
Detect lack of media
Auto verify label status
Detect postion status
Page mode status
Current printing speed
Current printing width
Complete
Tally Dascom
45
Tally Dascom DL-210
User Guide V1.3
4.2 Hexadecimal Dumping Mode
Hold down Feed Key and switch on printer till Power LED blinks three times, buzzer beeps
three times.
When self-test is OK but on-line printing error occurs, you can check the communication
between PC and program via Hexadecimal Dump mode. In Hexadecimal Dump mode, the
printer will print out hexadecimal data once it receives the signal from host. You can ask
technical service for analysis.
The printer starts printing “HEX DUMP PRINT MODE” followed by the received data printed in
hexadecimal numbers and some characters.
CAUTION!
The printer prints “.” if there is no characters corresponding to data.
During hexadecimal dump, functions except some command will be disabled.
If print data does not cover a line, press the FEED switch to print the line.
Printing example:
0123456789abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ
Press the FEED button one time to feed the last line after the printer stops printing so as to
return to the normal mode.
46
Tally Dascom DL-210
User Guide V1.3
4.3 Auto Calibrate Label
DL-210 can calibrate label automatically. Hold down Feed Key and switch on printer till Power
LED blinks twice, buzzer beeps twice.
Label calibration should be executed in the following situations:
Use printer for printing label first time.
Replace different size of labels.
Printer skips labels
Printer feeds blank labels.
Refill with new roll of labels.
47
Tally Dascom DL-210
User Guide V1.3
5 TROUBLESHOOTING AND MAINTENANCE
Your printer is extremely reliable, but occasionally problems may occur. This chapter provides
information on some of the common problems you may encounter and how you may solve
them. If you encounter problems that you cannot resolve, please contact your dealer for
assistance.
Read the following instructions before maintenance and avoid incorrect operation, so as to
prevent injury to you and damage to the printer.
5.1 Common Issues
LED Indication and Buzzer Alarm
Condition
No LEDs on
Possible Cause
What to do?
Unplug power cord
Check power cord and plug it properly
Turn off printer
Turn on printer
PCB damaged
Contact service representatives
Check the cable and adapter, or change another
cable or/and adapter.
Check the cable and adapter, or change another
cable or/and adapter.
Power source unavailable
Shut down
Status LED always on
Media end
Re-load media
Error LED always on
Print head mechanism open
Close the print head mechanism
Label remains in peeler
Remove label
Ribbon end
Replace ribbon
Thermal print head
overheated
Turn the printer off and wait some minutes before
resume
Over-voltage
Print with specified voltage
Low-voltage
Print with specified voltage
Power LED and Error
LED fast blink three
time, buzzer alarms
three times
Gap sensor error alarm. The
black mark sensor does not
align with the receiving
sensor, that it, two triangles
do not align.
Move around the black mark sensor, so that the its
triangle aligns with another on the center housing.
Press feed button after
power on, Error LED
slowly blinks once and
then fast blinks three
times; buzzer alarms
four times
Cutter error alarm. Enable
cutter function but without
cutter installation.
Disable the cutter in the tool.
Gap detection error.
1. Use continuous paper but set label in the tool.
Change to “label paper” in the tool.
2. Due to sensor error or other problems, the
sensor could not detect the gap. Clean or/and
adjust the media sensor.
Status LED blinks
Error LED blinks and
buzzer alarms
Error LED fast blinks
48
Tally Dascom DL-210
User Guide V1.3
Printing Error
Condition
Possible Cause
What to do?
Incorrect media roll installation
Check media roll and re-load it properly
Media is out of specification
Use recommended media
Dirty thermal print head or platen
Clean print head or platen
Ribbon is out of specification
Use recommended ribbon
Low print density
Increase the print density (heat)
Print with Ribbon on Direct
Thermal paper
Remove ribbon
Self-test fail
Hardware problem
Contact service representatives
Media jam
Label stuck
Blurred or spot printing
Check media path and clean jammed label,
refer to Chapter 5 Section 5.3
Label positioning problem or label
Execute label calibration (refer to Chapter 4
size setting exceeds the physical
section 4.3).If it doesn’t work, you have to
size.
verify the label size setting is correct or not.
Printer feeds blank labels
Print without ribbon on transfer
thermal paper
Install ribbon
Paper size setting correct
but the printout is
crooked, skewed, or
off-center.
Label did not calibrate correctly
Execute label calibration (refer to Chapter 4
section 4.3).
Printer skips labels
5.2 Resetting the Factory Default Values
Sometimes, resetting the printer to the factory defaults may solve some problems.
There are two methods to set to factory setting:
Method one: Hold down Feed Key and switch on printer till Power LED blinks four times,
buzzer beeps four times.
Method two: through setup tool, choose restore all setting on printer setup page.
5.3 Removing Jammed Label
Printhead may be hot, please do not touch!
(1) Turn printer off, open top cover and turn up print head mechanism.
(2) Remove the jammed label and ribbon, clean the print head with a cotton swab with alcohol
in case of ribbon paste on print head and cause poor print quality.
(3) Reload media.
(4) Reload ribbon and turn the ribbon adjustor for rewinding the sticky part.
49
Tally Dascom DL-210
User Guide V1.3
5.4 Cleaning Thermal Print Head
After printing, the print head becomes very hot. Be careful not to touch it and
to let it cool before you clean it.
Do not damage the print head by touching it with your fingers or any hard
object.
Turn off the printer, open the top cover and remove ribbon, clean the thermal elements of
the print head with a cotton swab moistened with alcohol solvent (ethanol, methanol, or
isopropyl).
Be gentle with the cleaning so as not to damage the printhead.
We recommend cleaning the thermal print head periodically (generally every 3 months) to
maintain print quality.
5.5 Maintenance
DL-210 is designed for a long and reliable lifetime. But periodic maintenance is recommended
in order to assure error free working. This also would guarantee the good print quality over the
life time. It is recommended to clean the printer once every six months or after 300 hours duty.
Before cleaning, switch off the printer, wait a few seconds and unplug the power cord.
Open the cover and remove the dust, paper shreds and other debris from inside by using a
soft vacuum cleaner or a brush.
In order to remove the dirt, you can wipe clean the machine with a soft cloth dipped in
alcohol instead of the ketone or TEC solvent which may cause damage to the plastic parts.
Please be aware that excessive moisture will lead to the improper functioning of electronic
parts.
Clean the platen roller with soft cloth.
While you are cleaning the printer, in order to avoid short circuit, do not damage or loose the
cable or electronic parts, do not drop metal material inside, such as Paper Clips or Pins.
50
Tally Dascom DL-210
User Guide V1.3
6 COMMUNICATION INTERFACES SPECIFICATIONS
6.1 USB interface
USB interface pin assignment
PIN No.
Description
VBUS
DD+
GND
Classic wire color
Red
White
Green
Black
USB interface connector diagram
6.2 Wi-Fi interface
Wi-Fi interface supports 2.4 GHz, IEEE Std. 802.11b/g standard.
6.4 Ethernet interface
Ethernet interface pin assignment
Pin. No.
Name
TX+
Description
Tranceive Data+
TXRX+
n/c
n/c
RXn/c
n/c
Tranceive DataReceive Data+
Not connected
Not connected
Receive DataNot connected
Not connected
51
Tally Dascom DL-210
User Guide V1.3
Ethernet interface connector diagram
6.5 Serial interface
Serial interface pin assignment
Serial interface compatible with RS-232 standard, with 25 pin (D hole type) socket.
PIN No.
PIN 1
PIN 2
PIN 3
PIN 4
PIN 5
PIN 6
PIN 7
PIN 8~19
PIN 20
PIN 21~25
Description
Frame Ground
TXD
RXD
RTS
Unconnected
DSR
Signal Ground
Unconnected
DTR
Unconnected
User can view the setting of interface via printing configuration sample.
The default setting of serial interface is as follow, 38400 bps (baud rates), 8 bit (data bit), 1 bit
(stop bit), no parity, support RTS/CTS handshaking protocol.
Serial interface connector diagram
52
Tally Dascom DL-210
User Guide V1.3
6.6 Parallel interface
Parallel interface pin assignment
Parallel interface with 36 pin CENTRONICS socket.
Pin No.
Signal From
10
11
12
13
14
15
16
17
18
19~30
31
32
Description
Strobe Signal; Data latch pulse, latch the data to the printer
at the rising edge of the negative pulse.
Data 0 (The lowest bit)
Data 1
Data 2
Data 3
Data 4
Data 5
Data 6
Data 7 (The highest bit)
ACK Signal; Printer response signal, indicates that the
printer has received a Data byte.
Busy Signal; The printer is busy; High level indicates that
the printer can’t receive data.
PE Signal; Paper end signal; High level indicates that the
printer is out of paper.
Unconnected
Unconnected
Unconnected
－
－
－
Logic Ground
Frame Ground, separated from logic ground.
5V/500mA power output
－
Logic Ground
Initialization signal
－
Printer error signal. Low level indicates that an error occurs
in the printer. It will come with paper end.
Logic Ground
Unconnected
－
Unconnected
33
34~35
36
Remarks:
H indicates that signal comes from Host computer; P indicates that signal comes from Printer.
Parallel interface connector diagram
53
Tally Dascom DL-210
User Guide V1.3
6.7 Power Supply
(1) Power adapter
Input: AC 100V-240V~ 1.5A 50-60Hz
Output: DC 24V±5%, 2.1A, A-1009-3P interface
(2) Power Supply connector diagram
(3) Power Socket pin assignment
Pin Number
Signal Name
+24 V
GND
N.C
SHELL
F.G.
(4) Power Supply interface type
Printer - Unetop DC-002 or similar products
Computer - Unetop DP-002 or similar products
54
Tally Dascom DL-210
User Guide V1.3
7 CHARACTER CODE PAGES
The character code tables show only character configurations. They do
not show the actual print pattern.
“SP” in the table shows a space.
7.1 Common to all pages (International Character Set: USA)
HEX
NUL
DLE
00
16
XON
01
18
XOFF
03
EOT
04
ENQ
07
38
‘
23
08
39
24
40
09
25
41
10
26
ESC
11
FF
FS
CR
13
43
29
45
30
31
61
46
62
47
55
79
109
94
125
110
95
124
123
108
93
78
63
122
107
92
77
106
91
121
105
90
76
120
75
60
104
89
74
59
44
15
58
119
118
103
88
73
RS
14
42
28
GS
57
102
117
87
72
27
12
56
116
101
86
71
115
100
85
70
55
99
84
114
LF
54
98
83
69
HT
113
68
53
97
82
67
112
52
37
22
CAN
06
51
96
81
66
36
21
ACK
NAK
50
35
80
65
20
05
34
19
64
49
DC4
48
33
“
02
32
17
SP
126
SP
111
127
Tally Dascom DL-210
User Guide V1.3
7.2 International Character Sets
ASCII code (Hex)
Country
23
24
40
5B
5C
5D
5E
60
7B
7C
7D
7E
USA
France
à
°
ç
§
é
ù
è
¨
Germany
§
Ä
Ö
Ü
ä
ö
ü
β
U.K.
£
Denmark I
Æ
Ø
Å
æ
ø
å
Sweden
¤
É
Ä
Ö
Å
Ü
é
ä
ö
å
ü
Italy
°
é
ù
à
ò
è
ì
Spain I
Pt
¡
Ñ
¿
¨
ñ
Japan
¥
Norway
¤
É
Æ
Ø
Å
Ü
é
æ
ø
å
ü
Denmark II
É
Æ
Ø
Å
Ü
é
æ
ø
å
ü
Spain II
á
¡
Ñ
¿
é
í
ñ
ó
ú
Latin America
á
¡
Ñ
¿
é
ü
í
ñ
ó
ú
Korea
Slovenia/ Croatia
Ž
Š
Đ
Ć
Č
š
đ
ć
č
China
Ұ
56
ž
Tally Dascom DL-210
User Guide V1.3
7.3 [User-defined page]
HEX
SP
SP
128
SP
144
SP
129
SP
130
146
131
132
SP
148
133
SP
137
SP
156
141
SP
173
158
189
174
190
SP
175
57
237
222
253
SP
238
SP
223
252
SP
SP
SP
207
236
221
206
251
SP
SP
SP
SP
191
235
220
205
SP
250
SP
SP
SP
249
SP
234
219
204
SP
SP
SP
159
188
233
SP
SP
248
SP
SP
218
203
SP
SP
SP
SP
143
172
157
142
187
SP
SP
SP
247
232
217
202
SP
SP
SP
SP
SP
171
SP
SP
246
SP
231
216
201
186
230
215
SP
245
SP
SP
SP
SP
SP
SP
SP
185
229
214
200
SP
SP
170
155
140
SP
169
SP
SP
SP
244
SP
SP
SP
199
184
SP
SP
154
139
SP
228
213
198
243
SP
SP
SP
SP
183
168
SP
SP
SP
167
153
138
182
227
212
197
242
SP
SP
SP
SP
SP
SP
SP
SP
166
152
SP
181
226
211
196
241
SP
SP
SP
SP
SP
SP
151
136
SP
165
150
135
180
225
210
195
240
SP
SP
SP
SP
SP
SP
SP
SP
164
149
134
SP
179
224
209
194
SP
SP
SP
SP
SP
SP
SP
178
163
208
193
SP
SP
SP
SP
SP
SP
SP
162
147
192
177
SP
SP
SP
SP
SP
176
161
SP
SP
SP
SP
SP
160
145
SP
SP
SP
SP
SP
254
SP
239
255
Tally Dascom DL-210
User Guide V1.3
7.4 [PC437: USA, Standard Europe]
HEX
Ç
128
ü
é
145
Æ
130
â
ä
ö
à
148
133
å
150
135
ê
Ü
Ä
157
142
173
╛
158
174
159
╬
190
┐
»
175
205
191
58
207
Φ
222
²
253
■
238
∩
223
252
237
ε
▀
251
236
221
206
250
√
∞
▐
╧
·
235
220
▌
249
234
δ
▄
═
189
Ω
219
204
248
•
233
218
█
╠
188
╜
«
ƒ
143
╝
232
217
203
247
°
Θ
┌
╦
231
216
202
187
172
¡
Pt
Å
╗
¼
¥
╩
246
≈
Ф
┘
201
186
171
156
141
║
230
215
200
245
÷
τ
╪
╔
185
170
½
£
ì
169
155
140
184
229
214
199
244
⌡
μ
╫
╚
╣
¬
¢
î
168
154
139
183
228
213
198
243
⌠
σ
╓
╟
╕
┌
153
138
ï
167
152
137
182
227
212
197
242
≤
Σ
╒
╞
╖
¿
Ö
è
166
151
136
181
226
211
196
241
≥
π
╘
┼
╢
ÿ
ë
165
ù
180
225
210
195
240
±
Γ
╙
─
╡
Ñ
û
ç
┤
β
╥
├
≡
224
209
194
179
164
149
134
163
ñ
ò
178
│
ú
208
193
┬
α
╤
┴
▓
╨
192
177
162
147
132
▒
ó
ô
└
176
161
146
131
160
í
æ
░
á
144
129
É
254
SP
239
255
Tally Dascom DL-210
User Guide V1.3
7.5 [PC850: Multilingual]
HEX
Ç
128
ü
é
145
Æ
130
â
ä
à
ò
å
149
134
ç
ù
ê
ï
¡
×
142
143
189
190
┐
»
175
206
191
59
207
¹
252
²
237
253
■
¯
222
238
´
223
251
³
Ý
▀
¤
250
236
221
Ì
╬
¥
174
·
ý
¦
249
235
220
205
¨
Ù
▄
248
234
219
204
═
¢
«
159
╠
°
Û
█
247
233
218
203
188
173
158
ƒ
Å
172
157
╦
¸
Ú
┌
246
232
217
202
187
╝
¼
Ø
Ä
171
156
╩
÷
Þ
┘
245
231
216
201
186
╗
½
£
140
ì
170
155
╔
§
þ
Ï
244
230
215
200
185
║
¬
ø
î
169
154
139
╣
®
Ü
138
184
243
¶
μ
Î
╚
©
¾
229
214
199
242
Õ
Í
Ã
226
228
213
198
183
168
153
141
¿
Ö
è
167
152
137
182
241
227
212
197
225
õ
ı
ã
À
ÿ
ë
166
151
136
181
Â
211
196
±
Ò
È
┼
Á
Ë
─
240
Ô
210
195
180
165
150
135
164
Ñ
û
179
224
209
194
β
Ê
├
┤
ñ
148
133
163
208
193
178
Ó
Ð
┬
│
ú
ö
┴
▓
ð
192
177
162
147
132
▒
ó
ô
└
176
161
146
131
160
í
æ
░
á
144
129
É
254
SP
239
255
Tally Dascom DL-210
User Guide V1.3
7.6 [PC852: Latin2]
HEX
Ç
É
128
ĺ
é
130
â
ô
ä
ů
ć
149
135
ł
ë
137
Ő
î
Ź
141
Ä
173
174
═
175
60
ř
ţ
253
■
238
´
223
252
237
222
▀
207
251
Ř
Ý
Ů
¤
191
ű
236
221
206
250
235
ý
Ţ
╬
•
Ű
220
205
190
┐
»
159
204
189
ż
«
158
č
143
188
249
234
219
▄
248
¨
ŕ
█
╠
Ż
ş
×
Ć
╝
°
233
218
203
247
232
Ú
┌
╦
¸
Ŕ
217
202
187
172
157
142
171
Č
Ł
╩
246
231
216
┘
245
÷
š
ě
201
186
╗
ź
156
140
170
155
ť
185
§
230
215
200
╔
║
SP
Ť
139
169
154
╚
184
╣
ę
Ü
ő
168
214
199
244
229
Š
Î
ă
˘
ň
Í
243
228
213
198
183
Ş
Ę
153
138
Ě
167
152
Ö
182
ˇ
ń
Ň
242
227
212
197
Ă
Â
ž
ś
136
181
˛
Ń
ď
241
226
211
196
┼
Á
166
151
─
˝
Ô
Ë
240
225
210
195
180
165
150
Ś
ç
┤
Ž
ľ
179
164
ą
Ľ
134
Ą
148
133
163
Ď
├
224
209
194
β
Ð
┬
Ó
208
193
178
│
ú
ö
┴
▓
đ
192
177
162
147
132
▒
ó
└
176
161
146
131
160
145
░
í
Ĺ
ü
á
144
129
254
SP
239
255
Tally Dascom DL-210
User Guide V1.3
7.7 [PC858: Euro]
HEX
Ç
É
128
ü
é
145
Æ
130
â
ä
ö
132
à
148
133
å
ù
ê
Ö
138
ï
Ø
Ä
¡
×
142
158
143
189
174
190
┐
175
61
207
³
252
²
237
222
253
■
¯
238
´
223
251
236
Ý
▀
¤
191
¹
ý
Ì
250
235
221
206
·
Ù
¦
249
234
220
205
╬
¥
»
159
═
¢
¨
Û
▄
248
233
219
204
247
°
Ú
█
╠
¸
232
218
203
188
173
«
ƒ
Å
172
157
╦
187
╝
¼
202
246
231
217
┌
245
÷
Þ
┘
╩
§
þ
216
201
186
171
156
╔
╗
½
£
140
ì
170
155
200
185
║
¬
ø
î
169
154
139
╣
®
Ü
184
244
230
215
Ï
╚
©
¶
μ
Î
243
229
214
199
¾
Õ
Í
Ã
183
168
153
141
¿
152
137
è
167
242
228
213
198
226
õ
€
ã
241
227
212
197
182
À
ÿ
ë
166
151
136
181
Â
È
┼
Á
±
225
Ò
211
196
240
Ô
Ë
─
180
165
150
135
Ñ
û
ç
┤
β
210
195
224
209
Ê
├
Ó
Ð
194
179
164
149
134
163
ñ
ò
178
208
193
┬
│
ú
ð
┴
▓
192
177
162
147
└
▒
ó
ô
176
161
146
131
160
í
æ
░
á
144
129
254
SP
239
255
Tally Dascom DL-210
User Guide V1.3
7.8 [PC860: Portuguese]
HEX
Ç
128
ü
é
145
È
130
â
ã
õ
à
148
133
Á
150
135
Ê
Ü
Ã
157
142
173
╛
158
174
159
╬
190
┐
»
175
205
191
62
207
Φ
222
²
253
■
238
∩
223
252
237
ε
▀
251
236
221
206
250
√
∞
▐
╧
·
235
220
▌
249
234
δ
▄
═
189
Ω
219
204
248
•
233
218
█
╠
188
╜
«
Ó
143
╝
232
217
203
247
°
Θ
┌
╦
231
216
202
187
172
¡
Pt
Å
╗
¼
Ù
╩
246
≈
Ф
┘
201
186
171
156
141
║
230
215
200
245
÷
τ
╪
╔
185
170
½
£
ì
169
155
140
184
229
214
199
244
⌡
μ
╫
╚
╣
¬
¢
Ô
168
154
139
183
228
213
198
243
⌠
σ
╓
╟
╕
Ò
153
138
Í
167
152
137
182
227
212
197
242
≤
Σ
╒
╞
╖
¿
Õ
è
166
151
136
181
226
211
196
241
≥
π
╘
┼
╢
Ì
ê
165
ù
180
225
210
195
240
±
Γ
╙
─
╡
Ñ
Ú
ç
┤
β
╥
├
≡
224
209
194
179
164
149
134
163
ñ
ò
178
│
ú
208
193
┬
α
╤
┴
▓
╨
192
177
162
147
132
▒
ó
ô
└
176
161
146
131
160
í
À
░
á
144
129
É
254
SP
239
255
Tally Dascom DL-210
User Guide V1.3
7.9 [PC863: Canadian-French]
HEX
Ç
128
ü
é
145
â
131
Â
147
132
148
Ï
à
133
¶
150
135
ê
ë
153
138
ï
î
140
141
142
143
╜
═
174
╬
190
┐
175
╧
191
63
222
²
253
■
238
∩
223
252
237
ε
▀
207
Φ
▐
251
236
221
206
√
∞
▌
250
235
220
205
·
δ
▄
249
234
219
204
189
╛
»
159
╠
•
Ω
█
248
233
218
203
188
173
«
ƒ
§
╝
¾
158
╦
°
Θ
┌
247
232
217
202
187
172
157
Û
À
171
156
╩
≈
Ф
┘
246
231
216
201
186
╗
¼
Ù
║
½
£
╔
÷
τ
╪
245
230
215
200
185
170
155
╚
⌡
μ
╫
244
229
214
199
184
╣
¬
¢
139
╕
169
154
╟
⌠
σ
╓
243
228
213
198
183
168
┌
Ü
è
╖
Î
Ô
╞
≤
Σ
╒
242
227
212
197
182
167
152
137
╢
¯
¤
┼
≥
π
╘
241
226
211
196
181
166
151
136
165
³
ù
180
225
210
195
240
±
Γ
╙
─
╡
¸
û
ç
┤
β
╥
├
≡
224
209
194
179
164
149
134
163
208
193
178
α
╤
┬
│
¨
Ë
192
177
162
╨
┴
▓
ú
ô
176
161
146
└
▒
ó
Ê
130
160
´
È
░
¦
144
129
É
254
SP
239
255
Tally Dascom DL-210
User Guide V1.3
7.10 [PC865: Nordic]
HEX
Ç
128
ü
æ
é
131
ä
147
à
148
ò
133
å
149
134
ç
ù
ê
ë
è
ï
î
ì
Ä
143
╜
═
174
╬
190
┐
¤
175
╧
191
64
Φ
▐
²
ε
253
■
238
∩
223
252
237
222
▀
207
251
236
221
206
√
∞
▌
250
235
220
205
·
δ
▄
249
234
219
204
189
╛
«
159
╠
•
Ω
█
248
233
218
203
188
173
158
ƒ
Å
╝
¡
Pt
╦
°
Θ
┌
247
232
217
202
187
172
157
142
╗
¼
Ø
╩
≈
Ф
┘
246
231
216
201
186
171
156
141
║
½
£
╔
÷
τ
╪
245
230
215
200
185
170
155
140
╣
¬
ø
╚
⌡
μ
╫
244
229
214
199
184
169
154
139
╕
┌
Ü
╟
⌠
σ
╓
243
228
213
198
183
168
153
138
182
227
212
197
242
≤
Σ
╒
╞
╖
¿
Ö
137
╢
167
152
┼
≥
π
╘
241
226
211
196
181
166
151
136
165
ÿ
180
225
210
195
240
±
Γ
╙
─
╡
150
135
164
Ñ
û
179
224
209
194
≡
β
╥
├
┤
ñ
ö
132
163
208
193
178
α
╤
┬
│
ú
192
177
162
╨
┴
▓
ó
ô
176
161
146
└
▒
í
Æ
â
160
145
130
░
á
144
129
É
254
SP
239
255
Tally Dascom DL-210
User Guide V1.3
7.11 [PC866: Cyrillic #2]
HEX
А
Р
128
Б
С
В
Г
147
Ф
132
Е
Х
133
Ж
И
Й
К
Л
М
Н
О
П
╜
╛
190
175
╧
191
65
222
¤
253
■
254
238
я
223
252
237
ю
▀
207
№
э
▐
251
236
221
206
√
ь
▌
250
235
220
205
╬
┐
п
159
═
·
ы
▄
249
234
219
204
189
174
158
╠
•
ъ
█
248
233
218
203
188
173
о
Я
143
╝
н
Ю
╦
°
щ
┌
247
232
217
202
187
172
157
142
╗
м
Э
╩
ў
ш
┘
246
231
216
201
186
171
156
141
║
л
Ь
╔
Ў
ч
╪
245
230
215
200
185
170
155
140
╣
к
Ы
╚
ї
ц
╫
244
229
214
199
184
169
154
139
╕
й
Ъ
╟
Ї
х
╓
243
228
213
198
183
168
153
138
╖
и
Щ
╞
є
ф
╒
242
227
212
197
182
167
152
137
╢
з
Ш
┼
Є
у
╘
241
226
211
196
181
166
151
136
╡
ж
Ч
─
ё
т
╙
240
225
210
195
180
165
150
135
е
Ц
З
┤
с
╥
├
Ё
224
209
194
179
164
149
134
│
д
╤
┬
р
208
193
178
163
148
┴
▓
╨
192
177
162
г
У
Д
▒
в
└
176
161
146
131
б
Т
░
160
145
130
а
144
129
SP
239
255
Tally Dascom DL-210
User Guide V1.3
7.12 [PC720: Arabic]
HEX
SP
ب
SP
128
144
129
145
160
ة
SP
130
146
▒
ث
ô
131
147
SP
132
à
148
SP
149
ç
150
135
151
ء
136
153
138
139
س
140
156
141
142
143
╜
╛
174
┐
»
159
190
175
66
207
250
√
251
ⁿ
236
252
237
222
253
■
238
ي
223
249
·
ى
▀
SP
191
248
·
و
▐
247
°
235
221
206
≈
ه
▌
╧
246
ن
220
205
230
234
219
▄
╬
189
245
233
218
204
229
م
█
╠
244
232
217
203
188
173
«
ا
SP
╝
ص
158
╦
228
ل
┌
202
187
172
157
ئ
SP
186
243
231
216
201
227
ك
┘
╩
╗
ش
إ
SP
185
171
215
200
242
ق
╪
╔
║
170
155
￡
î
184
169
154
199
226
μ
214
╫
╚
╣
ز
ؤ
ï
168
ر
أ
183
241
ف
213
╓
╟
╕
212
198
225
غ
╒
╞
╖
211
197
182
167
152
137
è
╢
ذ
آ
ë
┼
240
ع
╘
196
181
166
د
ù
ê
╡
210
╙
─
224
ظ
╥
195
180
165
خ
û
134
179
164
209
194
≡
ط
╤
├
┤
ح
133
178
163
208
193
┬
│
ج
¤
┴
▓
ض
╨
192
177
162
└
176
161
ت
é
░
254
SP
239
255
Tally Dascom DL-210
User Guide V1.3
8 COMMAND SETS
8.1 ESC/POS Command Sets
Category
Print commands
Print position
commands
Miscellaneous
Function
Commands
Chinese Character
control commands
Commands
Function
LF
Print and line feed
FF
Print and feed paper to the head of
next page (in page mode)
CR
Print and carriage return
ESC J n
Print and feed paper
HT
Horizontal tab
ESC $ nL nH
Set absolute print position
ESC D n1...nk NUL
Set horizontal tab positions
ESC \ nL nH
Set relative print position
ESC a n
Select justification
ESC d n
Print and feed n lines
ESC t n
Select character code table
GS L nL nH
Set left margin
GS W nL nH
Set print area width
ESC = n
Select printer
ESC @
Initialize printer
GS P x y
Set horizontal and vertical motion
units
FS ! n
Set Chinese character mode
FS &
Select Chinese character mode
FS - n
Turn on/off Chinese character
underline mode
FS
Cancel Chinese character mode
FS 2 c1 c2 d1...dk
Define user-defined Chinese character
FS C n
Select Chinese character code system
Set Chinese character left and right
FS S n1 n2
spacing
Turn on/off Chinese double height and
FS W n
Space commands
Control panel
commands
double width
ESC 2
Select default line spacing
ESC 3 n
Set line spacing
ESC c 5 n
Enable/disable panel buttons
67
Tally Dascom DL-210
Category
User Guide V1.3
Commands
Function
ESC SP n
Set right-side character spacing
ESC ! n
Select print mode(s)
ESC % n
Select/cancel user-defined character
set
ESC & y c1 c2 [x1 d1...d(y ×
x1)]...[xk d1...d(y × xk)]
Define user-defined characters
ESC - n
Turn on/off underline mode
ESC ? n
Cancel user-defined characters
Character control
ESC E n
Turn emphasized mode on/off
commands
ESC G n
Turn double-strike mode on/off
ESC M n
Select character font
ESC R n
Select an international character set
Turn on/off 90 degrees clockwise
ESC V n
Barcode
commands
rotation mode
ESC { n
Turn on/off upside-down print mode
GS ! n
Select character size
GS B n
Turn white/black reverse print mode
on/off
GS H n
Select print position of HRI
characters
GS f n
Select font for HRI characters
GS h n
Set bar code height
①GS k m d1...dk NUL
Print bar code
②GS k m n d1...dn
GS w n
Set barcode width
ESC Z m n k dL dH d1 …dn
Print 2D barcode
GS Z n
Select 2D barcode type
①GS k m v r d1...dn NUL
②GS k m v r nL nH d1...dn
Bit image
commands
Print 2D barcode
ESC * m nL nH d1... Dk
Select bit-image mode
FS P n
Print NV bit image
GS * x y d1...d(x × y × 8)
Define downloaded bit image
68
Tally Dascom DL-210
User Guide V1.3
8.2 ZPL Command Sets
Commands
Function
^A
Scalable/Bitmapped Font
^A@
Use Font Name to Call Font
^B0
Aztec Bar Code Parameters
^B1
Code 11 Bar Code
^B2
Interleaved 2 of 5 Bar Code
^B3
Code 39 Bar Code
^B4
Code 49 Bar Code
^B5
Planet Code bar code
^B7
PDF417 Bar Code
^B8
EAN-8 Bar Code
^B9
UPC-E Bar Code
^BA
Code 93 Bar Code
^BB
CODABLOCK Bar Code
^BC
Code 128 Bar Code (Subsets A, B, and C)
^BD
UPS MaxiCode Bar Code
^BE
EAN-13 Bar Code
^BF
MicroPDF417 Bar Code
^BI
Industrial 2 of 5 Bar Codes
^BJ
Standard 2 of 5 Bar Code
^BK
ANSI Codabar Bar Code
^BL
LOGMARS Bar Code
^BM
MSI Bar Code
^BO
Aztec Bar Code Parameters
^BP
Plessey Bar Code
^BQ
QR Code Bar Code
^BR
GS1 Databar (formerly Reduced Space Symbology)
^BS
UPC/EAN Extensions
^BT
TLC39 Bar Code
^BU
UPC-A Bar Code
^BX
Data Matrix Bar Code
^BY
Bar Code Field Default
^CC ~CC
Change Caret
^BZ
POSTAL Bar Code
69
Tally Dascom DL-210
User Guide V1.3
Commands
Function
^CD
~CD Change Delimiter
^CF
Change Alphanumeric Default Font
^CI
Change International Font/Encoding
^CM
Change Memory Letter Designation
^CO
Cache On
^CP
Remove Label
^CV
Code Validation
^CW
Font Identifier
~DB
Download Bitmap Font
~DE
Download Encoding
^DF
Download Format
~DG
Download Graphics
~DN
Abort Download Graphic
~DS
Download Intellifont (Scalable Font)
~DT
Download Bounded TrueType Font
~DU
Download Unbounded TrueType Font
~DY
Download Objects
~EG
Erase Download Graphics
^FB
Field Block
^FC
Field Clock
^FD
Field Data
^FH
Field Hexadecimal Indicator
^FL
Font Linking
^FM
Multiple Field Origin Locations
^FN
Field Number
^FO
Field Origin
^FP
Field Parameter
^FR
Field Reverse Print
^FS
Field Separator
^FT
Field Typeset
^FV
Field Variable
^FW
Field Orientation
^FX
Comment
^GB
Graphic Box
70
Tally Dascom DL-210
User Guide V1.3
Commands
Function
^GC
Graphic Circle
^GD
Graphic Diagonal Line
^GE
Graphic Ellipse
^GF
Graphic Field
^GS
Graphic Symbol
~HB
Battery Status
~HD
Head Diagnostic
^HF
Host Format
^HG
Host Graphic
^HH
Configuration Label Return
~HI
Host Identification
~HM
Host RAM Status
~HQ
Host Query
~HQ
Examples
~HS
Host Status Return
^HT
Host Linked Fonts List
~HU
Return ZebraNet Alert Configuration
^HV
Host Verification
^HW
Host Directory List
^HY
Upload Graphics
^HZ
Display Description Information
^ID
Object Delete
^IL
Image Load
^IM
Image Move
^IS
Image Save
~JA
Cancel All
^JB
Initialize Flash Memory
~JB
Reset Optional Memory
~JC
Set Media Sensor Calibration
~JD
Enable Communications Diagnostics
~JE
Disable Diagnostics
~JF
Set Battery Condition
~JG
Graphing Sensor Calibration
^JH
Early Warning Settings
71
Tally Dascom DL-210
User Guide V1.3
Commands
Function
^JI
Start ZBI (Zebra BASIC Interpreter)
~JI
Start ZBI (Zebra BASIC Interpreter)
^JJ
Set Auxiliary Port
~JL
Set Label Length
^JM
Set Dots per Millimeter
~JN
Head Test Fatal
~JO
Head Test Non-Fatal
~JP
Pause and Cancel Format
~JQ
Terminate Zebra BASIC Interpreter
~JR
Power On Reset
^JS
Sensor Select
~JS
Change Backfeed Sequence
^JT
Head Test Interval
^JU
Configuration Update
^JW
Set Ribbon Tension
~JX
Cancel Current Partially Input Format
^JZ
Reprint After Error
~KB
Kill Battery (Battery Discharge Mode)
^KD
Select Date and Time Format (for Real Time Clock)
^KL
Define Language
^KN
Define Printer Name
^KV
Kiosk Values
^LF
List Font Links
^LH
Label Home
^LL
Label Length
^LR
Label Reverse Print
^LS
Label Shift
^LT
Label Top
^MA
Set Maintenance Alerts
^MC
Map Clear
^MD
Media Darkness
^MF
Media Feed
^ML
Maximum Label Length
^MM
Print Mode
72
Tally Dascom DL-210
User Guide V1.3
Commands
Function
^MN
Media Tracking
^MP
Mode Protection
^MT
Media Type
^MU
Set Units of Measurement
^MW
Modify Head Cold Warning
^NC
Select the Primary Network Device
~NC
Network Connect
^ND
Change Network Settings
^NI
Network ID Number
~NR
Set All Network Printers Transparent
^NS
Change Wired Networking Settings
~NT
Set Currently Connected Printer Transparent
^PA
Advanced Text Properties
^PF
Slew Given Number of Dot Rows
^PH ~PH
Slew to Home Position
~PL
Present Length Addition
^PM
Printing Mirror Image of Label
^PN
Present Now
^PO
Print Orientation
^PP ~PP
Programmable Pause
^PQ
Print Quantity
^PR
Print Rate
~PR
Applicator Reprint
~PS
Print Start
^PW
Print Width
~RO
Reset Advanced Counters
^SC
Set Serial Communications
~SD
Set Darkness
^SE
Select Encoding Table
^SF
Serialization Field (with a Standard ^FD String)
^SI
Set Sensor Intensity
^SN
Serialization Data
^SP
Start Print
^SQ
Halt ZebraNet Alert
73
Tally Dascom DL-210
User Guide V1.3
Commands
Function
^SR
Set Print head Resistance
^SS
Set Media Sensors
^SZ
Set ZPL
^TB
Text Blocks
^TO
Transfer Object
~WC
Print Configuration Label
^WD
Print Directory Label
~WQ
Write Query
~WQ
Examples
^XA
Start Format
^XB
Suppress Backfeed
^XF
Recall Format
^XG
Recall Graphic
^XS
Set Dynamic Media Calibration
^XZ
End Format
^ZZ
Printer Sleep
74
Tally Dascom DL-210
User Guide V1.3
8.3 EPL Command Sets
Commands
Function
ASCII text
Bar Code (EAN-8 / EAN-13 / UPC-A / Interleaved 25 / Codabar /
UPC-E / Code39 / Code 128)
MaxCode (Data Matrix / PDF417 / QR Code)
Cut Immediate
Density
EI
Print Soft Font Info.
EK
Delete Soft Font
ES
Store Soft Font
Cut/peel position
GG
Tetrieve Graphics
GI
Print Graphics Info.
GK
Delete Graphic
GM
Store Graphic
Character Set Selection
JF
Enable Top of Form Backup
LO
Line Draw Black
LS
Line Draw Diagonal
Clear Image Buffer
Options Select
Print
Set Label Width
Set Form Width
Set Reference Point
Speed Select
Box Draw
Print Direction
；
Code Anotation
^@
Reset Printer
^default
Set Printer to Factory Defaults
75
Tally Dascom DL-210
User Guide V1.3
Appendix I: Installing the Cutter
Removing the Tear Bar
(1) Turn off the printer power and open the top cover and the print head mechanism, and then pull
the tear bar to your side.
(2) Lift the tear bar up and it can be easily removed.
76
Tally Dascom DL-210
User Guide V1.3
(3) The tear bar is removed.
Note: Do it in reverse steps so as to install the tear bar.
Installing the Auto Cutter
(1) Power down the printer before installing the cutter. Plug in the cutter connector to the printer.
77
Tally Dascom DL-210
User Guide V1.3
(2) Put the auto cutter onto the slot of the low casing.
(3) Move the auto cutter gently to the reverse board till you hear the click sound.
78
Tally Dascom DL-210
User Guide V1.3
(4) After installation you can use the auto cutter.
(5) Enable the cutter in the setup tool.
79
Tally Dascom DL-210
User Guide V1.3
Appendix: FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference. and
2) This device must accept any interference received, including interference that may cause
undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Re-orientate or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated withi minimum distance 20cm
between the radiator & your body.
80
Appendix III: DASCOM REPRESENTATIVES
GERMANY
SINGAPORE (ASIA PACIFIC)
DASCOM Europe GmbH
Heuweg 3
D-89079 Ulm
Deutschland
Tel.: +49 (0) 731 2075 0
Fax: +49 (0) 731 2075 100
www.dascom.com
DASCOM AP Pte Ltd
21 Bukit Batok Crescent
#29-81, WCEGA Tower
Singapore 658065
Phone: +65 6760 8833
Fax: +65 6760 1066
www.dascom.com
AMERICAS
UNITED KINGDOM
DASCOM Americas Corporation
34 Lakeview Court
Verona, VA 24482
USA
Phone:+1 (877) 434 13 77
Fax: +1 (540) 242 7221
www.dascom.com
DASCOM GB Ltd
Hart House, Priestley Road
Basingstoke, Hampshire
RG24 9PU, England
Phone: +44 (0) 1256 481481
Fax: +44 (0) 1256 481400
www.dascom.com
FRANCE
CHINA
DASCOM Europe GmbH
117 Avenue Victor Hugo
92100 Boulogne-Billancourt
France
Phone: +33 (1) 73 02 51 98
www.dascom.com
JIANGMEN DASCOM COMPUTER
PERIPHERALS CO., LTD
No. 399, Jinxing Road, Jianghai District,
Jiangmen, Guangdong P.R. China
www.dascom.com.cn
“All rights reserved. Translations, reprinting or copying by any means of this manual complete or in
part or in any different form requires our explicit approval. We reserve the right to make changes to
this manual without notice. All care has been taken to ensure accuracy of information contained in
this manual. However, we cannot accept responsibility for any errors or damages resulting from
errors or inaccuracies of information herein.”
© 2017 DASCOM
81
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Tagged PDF : Yes XMP Toolkit : 3.1-702 Create Date : 2016:10:21 11:52:17+08:00 Creator Tool : Microsoft® Word 2010 Modify Date : 2016:10:21 13:57:21+08:00 Metadata Date : 2016:10:21 13:57:21+08:00 Format : application/pdf Description : DT-210/230 User Guide Creator : WORK Title : Tally Dascom DT-210/230 Producer : Microsoft® Word 2010 Document ID : uuid:015df933-a5af-473e-a357-f17d5172c621 Instance ID : uuid:40f356dc-b292-408d-8a08-40e3ec06a68d Page Count : 94 Language : zh-CN Subject : DT-210/230 User Guide Author : WORKEXIF Metadata provided by EXIF.tools