Jiangmen Dascom Computer Peripherals TD11250 Dot Matrix Printer User Manual 1125 UG 2011 06 22

Jiangmen Dascom Computer Peripherals Co.,Ltd. Dot Matrix Printer 1125 UG 2011 06 22

User Manual

User Guide 1125 Matrix Printer
Tally Dascom 1125 I Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. • Never carry out maintenance or repair work yourself. Always contact a qualified service technician. • Keep this Operator’s Manual in a place which is easily accessible at all times. • Place the printer on a solid and even base so that it cannot fall. • Never place the printer in the vicinity of inflammable gas or explosive substances. • Ensure the printer is connected to a socket with the correct mains voltage. • Always disconnect the printer from the mains before opening the device to perform maintenance work or remedy errors. • Do not expose the printer to high temperatures, direct sunlight or dust. • Keep all liquids away from the printer. • Protect the printer from shock, impact and vibration. • Make sure that the printer and computer are switched off before connecting the data cable. • The print head will become very hot during printing; avoid contact with the print head after printing has finished. • Do not perform any operation or action in any way other than those provided in this manual. When in doubt, contact your dealer or your customer support.
Tally Dascom 1125 II Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen. xFühren Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie immer einen qualifizierten Servicetechniker. xBewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf. xDen Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann. xStellen Sie den Drucker keinesfalls in der Nähe von leicht entzündlichen Gasen oder explosiven Stoffen auf. xDen Drucker nur an eine Steckdose mit der richtigen Spannung anschließen. xWenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den Netzstecker an der Steckdose ziehen. xDen Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen. xKeine Flüssigkeiten mit dem Drucker in Berührung bringen. xDen Drucker keinen Erschütterungen, Stößen oder Vibrationen aussetzen. xSicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel angeschlossen wird. xDer Druckkopf wird während des Druckens heiß. Vor dem Berühren deshalb einige Zeit abkühlen lassen. xWeichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation ab. Bei Unklarheiten wenden Sie sich bitte an Ihren Händler oder Ihren Kundendienst.
Tally Dascom 1125 III Consignes importantes de sécurité (French) Lire attentivement les instructions suivantes avant de mettre l’imprimante en service. xNe jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un dépanneur qualifié. xPlacer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber. xNe jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de substances explosives. xNe connecter l’imprimante à une prise que lorsque la tension est correcte. xPour déconnecter l’imprimante de l’alimentation principale, mettre l’imprimante hors tension et toujours débrancher le connecteur secteur de la prise murale. xNe pas exposer l’imprimante à des températures élevées, à la lumière directe du soleil ou à la poussière. xNe pas mettre l’imprimante en contact avec des liquides. xNe pas exposer l’imprimante à des chocs, impacts ou vibrations. xS’assurer que l’imprimante et l’ordinateur sont hors tension avant de connecter le câble de données. xLa tête d’impression est brûlante pendant l’impression. C’est pourquoi laissez-la refroidir quelques instants avant d’y toucher. xN'exécutez aucune opération ni action d'une autre manière que celle indiquée dans ce manuel. En cas de doute, veuillez contacter votre distributeur ou service après-vente.
Tally Dascom 1125 IV Indicazioni di sicurezza importanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di assistenza qualificato. xConservare le presenti istruzioni per l’uso in un luogo sempre accessibile. xCollocare la stampante su una superficie stabile, per evitare che cada a terra. xNon collocare la stampante in prossimità di gas facilmente infiammabili o di sostanze esplosive. xCollegare la stampante a una presa di corrente con tensione adeguata. xPer scollegare la stampante dalla rete di alimentazione, spegnere la stampante e disinserire sempre il connettore di rete dalla presa. xNon esporre la stampante ad elevate temperature né alla luce solare diretta e alla polvere. xEvitare il contatto della stampante con liquidi. xNon esporre la stampante a colpi, scosse o vibrazioni. xVerificare che la stampante e il computer siano spenti prima di collegare il cavo di trasmissione dati. xDurante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessario opportuno quindi lasciarla raffreddare qualche istante. xNon eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale. In caso di dubbio, contattare il rivenditore o dalla società incaricata dell’assistenza.
Tally Dascom 1125 V Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. Nunca lleve a cabo trabajos de mantenimiento o reparación Ud. mismo, sino consulte a un técnico de servicio calificado. xGuarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento. xPonga la impresora sobre un base estable de manera que no pueda caer al suelo. xNunca coloque la impresora en la vecindad de gases de fácil inflamabilidad o sunstancias explosivas. xAsegure conectar la impresora sólo a un enchufe con un voltaje correcto. xCuando quiera desconectar la impresora de la red, apague la impresora y siempre tire la clavija de alimentación del enchufe. xNo exponga la impresora a temperaturas altas, a la luz solar directa y al polvo. xNo ponga la impresora en contacto con fluidos. xNunca exponga la impresora a sacudidas, choques o vibraciones. xAsegúrese de que la impresora y el ordenador estén apagdos antes de conectar el cable de datos. xLa cabeza de impresión se pone muy caliente durante la impresión. Por lo tanto, deje enfriarlo algún tiempo antes de tocarla. xNo permita que se realice cualquier operación o acción de una forma diferente a lo que se señala en el manual. En caso de duda, póngase en contacto con su comerciante o con su servicio post-venta.
Tally Dascom 1125 VI ɉɪɚɜɢɥɚ ɩɨ ɬɟɯɧɢɤɟ ɛɟɡɨɩɚɫɧɨɫɬɢ. (Russian) ɉɪɨɱɢɬɚɣɬɟ,ɩɨɠɚɥɭɣɫɬɚ,ɢɧɫɬɪɭɤɰɢɸ ɩɨ ɬɟɯɧɢɤɟ ɛɟɡɨɩɚɫɧɨɫɬɢ ɩɟɪɟɞ ɜɤɥɸɱɟɧɢɟɦ ɜ ɪɚɛɨɬɭ ɩɪɢɧɬɟɪɚ.xɇɟ ɜɵɩɨɥɧɹɣɬɟ ɬɟɯɧɢɱɟɫɤɢɟ ɪɚɛɨɬɵ ɢ ɪɟɦɨɧɬ ɬɟɯɧɢɤɢ ɫɚɦɨɫɬɨɹɬɟɥɶɧɨ,ɧɨ ɫɨɨɛɳɚɣɬɟ ɨɧɟɢɫɩɪɚɜɧɨɫɬɹɯ ɤɜɚɥɢɮɢɰɢɪɨɜɚɧɧɵɦ ɫɟɪɜɢɫɧɵɦ ɬɟɯɧɢɤɚɦ.xȾɚɧɧɚɹ ɢɧɫɬɪɭɤɰɢɹ ɞɨɥɠɧɚ ɛɵɬɶ ɜɫɟɝɞɚ ɞɨɫɬɭɩɧɚ ɤɚɠɞɨɦɭ ɩɨɥɶɡɨɜɚɬɟɥɸ.xɍɫɬɚɧɨɜɢɬɟ ɩɪɢɧɬɟɪ ɧɚ ɪɨɜɧɨɦ ɢ ɫɬɚɛɢɥɶɧɨɦ ɦɟɫɬɟ ɬɚɤ,ɱɬɨɛɵ ɨɧ ɧɟ ɫɦɨɝ ɭɩɚɫɬɶ ɧɚ ɩɨɥ.xɇɢ ɜ ɤɨɟɦ ɫɥɭɱɚɟ ɧɟ ɫɬɚɜɶɬɟ ɩɪɢɧɬɟɪ ɜɛɥɢɡɢ ɥɟɝɤɨ ɜɨɫɩɥɚɦɟɧɹɸɳɢɯɫɹ ɝɚɡɨɜ ɢ ɜɡɪɵɜɱɚɬɵɯɜɟɳɟɫɬɜ.xȼɤɥɸɱɚɣɬɟ ɩɪɢɧɬɟɪ ɜ ɪɨɡɟɬɤɭ ɬɨɥɶɤɨ ɫ ɫɨɨɬɜɟɬɫɬɜɭɸɳɢɦ ɧɚɩɪɹɠɟɧɢɟɦ.xȿɫɥɢ ȼɵ ɯɨɬɢɬɟ ɨɬɤɥɸɱɢɬɶ ɩɪɢɧɬɟɪ ɨɬ ɧɚɩɪɹɠɟɧɢɹ,ɫɧɚɱɚɥɚ ɜɵɤɥɸɱɢɬɟ ɩɪɢɧɬɟɪ ɫɚɦ ɢ ɡɚɬɟɦɜɵɧɶɬɟ ɲɬɟɤɟɪ ɢɡ ɪɨɡɟɬɤɢ. xȻɟɪɟɝɢɬɟ ɩɪɢɧɬɟɪ ɨɬ ɧɚɝɪɟɜɚɧɢɹ,ɨɬ ɩɨɩɚɞɚɧɢɹ ɧɚ ɧɟɝɨ ɩɪɹɦɵɯ ɫɨɥɧɟɱɧɵɯ ɥɭɱɟɣ ɢ ɩɵɥɢ.xɇɟ ɞɨɩɭɫɤɚɣɬɟ ɩɨɩɚɞɚɧɢɹ ɠɢɞɤɨɫɬɢ ɧɚ ɩɪɢɧɬɟɪ.xɇɟɥɶɡɹ ɩɨɞɜɟɪɝɚɬɶ ɩɪɢɧɬɟɪ ɬɪɹɫɤɟ,ɭɞɚɪɚɦ ɢ ɜɢɛɪɚɰɢɢ.xɍɛɟɞɢɬɟɫɶ,ɱɬɨ ɩɪɢɧɬɟɪ ɢ ɤɨɦɩɶɸɬɟɪ ɜɵɤɥɸɱɟɧɵ,ɬɨɥɶɤɨ ɩɨɫɥɟ ɷɬɨɝɨ ɫɨɟɞɢɧɢɬɟ ɩɪɢɧɬɟɪ ɫɤɨɦɩɶɸɬɟɪɨɦ.xɉɟɱɚɬɚɸɳɚɹ ɝɨɥɨɜɤɚ ɧɚɝɪɟɜɚɟɬɫɹ ɜɨ ɜɪɟɦɹ ɪɚɛɨɬɵ ɩɪɢɧɬɟɪɚ.ɉɨɷɬɨɦɭ ɩɨɞɨɠɞɢɬɟ ɤɚɤɨɟ-ɬɨɜɪɟɦɹ,ɩɪɟɠɞɟ ɱɟɦ ɞɨɬɪɨɧɭɬɶɫɹ ɞɨ ɧɟɟ.xɉɨɥɶɡɭɣɬɟɫɶ ɩɪɢɧɬɟɪɨɦ ɬɚɤ,ɤɚɤ ɷɬɨ ɧɚɩɢɫɚɧɨ ɜ ɞɨɤɭɦɟɧɬɚɰɢɢ.ȿɫɥɢ ɭ ȼɚɫ ɜɨɡɧɢɤɚɸɬ ɧɟɹɫɧɨɫɬɢ,ɨɛɪɚɳɚɣɬɟɫɶ ɫ ɜɨɩɪɨɫɚɦɢ ɤ ȼɚɲɢɦ ɩɪɨɞɚɜɰɚɦ ɢɥɢ ɜ ɫɟɪɜɢɫɧɵɣ ɰɟɧɬɪ.
Tally Dascom 1125 VII Instruções Importantes sobre Segurança (Portuguese) Leia as instruções de segurança antes de usar a impressora. xConsulte sempre um técnico qualificado para executar uma reparação . xColoque a impressora sobre uma base sólida e nivelada, para que ela não sofra quedas. xJamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias explosivas. xAssegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada. x Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da tomada. xNão exponha a impressora a temperaturas altas ou luz solar direta. xNão aproxime substâncias líquidas da impressora. xProteja a impressora de choques, impactos e vibrações. xDesligue a impressora e o computador antes de conectar o cabo da rede. xA cabeça da impressora pode ficar muito quente . Portanto, espere algum tempo antes de tocá-la. xNão faça nenhuma operação ou ação além das recomendadas neste manual. Em caso de dúvida, contate seu revendedor ou companhia de serviço.
Tally Dascom 1125 VIII Önemli Güvenlik Talimatları (Turkish) Lütfen, yazıcıyı iúletime geçirmeden önce bu güvenlik talimatlarını bütünüyle dikkatle okuyun. xBakım ve tamir çalıúmalarını kesinlikle ve hiçbir surette kendi baúınıza yapmayın; her zaman kalifiye bir uzman servis-teknisyenine haber verin. xYazıcıyı, üzerinden yere düúmesi mümkün olmayacak sabit ve düz bir zemine yerleútirin. xYazıcıyı kesinlikle ve hiçbir surette kolayca yanabilecek gaz veya patlayıcı maddeler içeren nesnelerin yakınına koymayın. xYazıcı akım kablosunu sadece do÷ru gerilime sahip bir prize takın. xYazıcıyı úebeke a÷ından ayırmak istedi÷inizde, yazıcıyı kapatın ve a÷-fiúini her zaman prizden çıkartın. xYazıcıyı ne yüksek ısılı ne de do÷rudan güneú ıúı÷ına ve toza mâruz kalan mekânlarda bulundurun. xYazıcı hiçbir sıvı maddeyle temasta olmamalıdır. xYazıcı hiçbir sarsıntıya, darbeye veya titreúime mâruz kalmamalıdır. xVeri kablosu ba÷lanmadan önce hem yazıcının hem de bilgisayarın kapalı olduklarından emin olmalısınız. xYazıcının baúı basma esnasında yüksek ısıya ulaúıyor. Bu yüzden lütfen dokunmadan önce kısa süre so÷umasını bekleyin. xYazıcının iúletimi ve kullanımında bu dokümantasyondaki talimatların hiç dıúına çıkmayın. Sorunlu görünen hususlarda lütfen imâlatçınıza veya müúteri hizmetleri servisinize baúvurun.
Tally Dascom 1125 IX TRADEMARK ACKNOWLEDGEMENTS “IBM” is a trademark of International Business Machines Corporation. “EPSON” is a trademark of Epson America Incorporated. “DEC” is a trademark of Digital Equipment Corporation. “Centronics” is a trademark of Centronics Data Computer Corporation. “DOS” is a trademark of Microsoft Corporation. “SAP” is a trademark of SAP AG. “Windows”, “Windows 7”, “Windows 95”, “Windows 98“, “Windows NT”, “Windows 2000”, “Windows 2003/2008 Server”, “Windows XP” and “Windows Vista” are trademarks of Microsoft Corporation. All other product names and company names appearing in this manual are the registered trademarks or trademarks of the individual companies.
Tally Dascom 1125 X
Tally Dascom 1125 XI TABLE OF CONTENTS 1 UNPACKING GUIDE ........................................................................................................................................ 1PLACING THE PRINTER .......................................................................................................................................... 2PRINTER COMPONENTS ........................................................................................................................................ 22 SETTING UP PRINTER .................................................................................................................................... 4INSTALL RIBBON .................................................................................................................................................. 4INSTALL THE SINGLE SHEET FEEDER....................................................................................................................... 5CONNECTING THE INTERFACE CABLE ...................................................................................................................... 5CONNECTING THE MAINS POWER .......................................................................................................................... 6INSTALLING THE WINDOWS DRIVER ........................................................................................................................ 73 PAPER INSTALLATION GUIDE ..................................................................................................................... 10ADJUSTING THE PRINT GAP LEVER ....................................................................................................................... 10FRICTION FEED HANDLING.................................................................................................................................. 11TRACTOR FEED HANDLING .................................................................................................................................. 12CONTINUOUS PAPER PLACEMENT ........................................................................................................................ 124 CONTROL PANEL OPERATION .................................................................................................................... 14PANEL OPERATION ............................................................................................................................................. 16Online State ............................................................................................................................................................ 17Setup State ............................................................................................................................................................. 18Power-On State ...................................................................................................................................................... 19LANGUAGE SETUP .............................................................................................................................................. 205 PRINTER SETTING CHANGES ..................................................................................................................... 21SYSTEM SETUP .................................................................................................................................................. 21PRINT SETUP ..................................................................................................................................................... 21PAGE SETUP ...................................................................................................................................................... 23INTERFACE SETUP .............................................................................................................................................. 24ADVANCED SETUP.............................................................................................................................................. 24VERTICAL ALIGNMENT ........................................................................................................................................ 34CHANGE PIN FUNCTION...................................................................................................................................... 35ADJUST PHYSICAL MARGINS ............................................................................................................................... 36DASCOM PRINTER SETUP TOOL ........................................................................................................................... 386 MAINTENANCE ............................................................................................................................................. 39CLEANING AND VACUUMING THE PRINTER ............................................................................................................. 39CLEANING THE PAPER ROLLERS ........................................................................................................................... 397 TROUBLESHOOTING .................................................................................................................................... 41PRINT QUALITY PROBLEMS AND SOLUTIONS ........................................................................................................ 41PAPER HANDLING PROBLEMS AND SOLUTIONS ..................................................................................................... 42OPERATING PROBLEMS AND SOLUTIONS .............................................................................................................. 42
Tally Dascom 1125 XII ERROR INDICATIONS ON LEDS ............................................................................................................................ 43DIAGNOSTIC FUNCTIONS .................................................................................................................................... 44FIRMWARE UPDATE ........................................................................................................................................... 458 GENERAL SPECIFICATIONS ......................................................................................................................... 469 INTERFACES .................................................................................................................................................. 51PARALLEL INTERFACE ......................................................................................................................................... 51USB INTERFACE ................................................................................................................................................ 52SERIAL INTERFACE ............................................................................................................................................. 5210 CHARACTER SETS & CODE PAGES .......................................................................................................... 53CHARACTER SETS .............................................................................................................................................. 53INTERNATIONAL CHARACTER SETS ........................................................................................................................ 55INTERNATIONAL CHARACTER SET COMMANDS ...................................................................................................... 55CHARACTER TABLES ........................................................................................................................................... 56CODE PAGE COMMANDS .................................................................................................................................... 58CODE PAGE TABLES ........................................................................................................................................... 6011 CONTROL CODES SUMMARY ................................................................................................................... 84EPSON EMULATION COMMAND LIST.................................................................................................................... 84IBM EMULATION COMMAND LIST ....................................................................................................................... 86FCC STATEMENT ............................................................................................................................................. 88
Tally Dascom 1125 11 Unpacking Guide xPlace your packaged printer on a solid base. xMake sure that the “Up” symbols point in the correct direction. xOpen the packaging, lift the printer out of the cardboard box and remove the remaining packaging material. xCheck the printer for any visible transport damage and missing items. If you find any transport damage or if any accessories are missing, please contact your dealer. The following items should be included: oPrinter oPaper feed knob oPaper feed tray oPower cord oRibbon cartridge oCD-ROM oInstallation Guide Remove the packaging materials from the printer as follows: 1. Remove the tape on the paper feed lever. 2. Remove other visible tape on the printer. 3. Open and remove the top cover of the printer. 4. Remove the shipping cardboard from around the print head. 5. Install the paper feed knob.
Tally Dascom 1125 2Placing the Printer Place the printer on a solid, flat, stable surface; ensuring that the printer is positioned in such a way that it cannot move, and that there is easy access to the control panel and paper input devices. Also ensure that there is enough space for sufficient ventilation and for the printed output. When selecting the printer location, observe the following additional instructions: xNever place the printer near to any flammable gas or explosive substances. xDo not expose the printer to direct sunlight. If you cannot avoid placing the printer near a window, protect it from the sunlight with a curtain. xWhen connecting a computer to the printer, make sure the maximum recommended cable length is not exceeded. xEnsure sufficient distance between the printer and any heating devices/radiators. xAvoid exposing the printer to extreme temperature or air humidity fluctuations. Avoid exposure to dusty environments. xIt is recommended the printer is installed in a position which reduces noise exposure to the work place during printing. Printer Components
Tally Dascom 1125 3 Component Function Gap Lever Controls printing impact or density. Adjusts the print gap lever according to the thickness of paper. Paper Guides Adjusts positioning of single sheet paper. Print Head 24-pin printing mechanism Top Cover Protects print head and other components inside, and reduce noise. Control Panel Shows printer status, for printer setup. Paper Feed Lever Two positions: = continuous forms; = single sheet paperPaper Feed Knob Manual feed or vertical positioning of paper Power Switch Power printer ON or OFF Ribbon Cartridge Install ribbon in the printer. Ribbon Frame For guiding ribbon installation on print head. Tractors For feeding and adjustment of continuous forms. Power Receptacle Connects power cord to the printer. Interface Connects interface cables from the host.
Tally Dascom 1125 42 Setting Up Printer Install Ribbon 1. Ensure the power to the printer is off and the print gap lever “A” is set to the furthest open position. Move the carriage to the centre of the print platen. 2. Install the recess positions c on the ribbon cassette into the printer mounting. 3. Press the ribbon frame d onto the print head. 4. Turn the ribbon knob e in clockwise direction until the ribbon fabric is taut. Move the carriage left and right to ensure the carriage and ribbon fabric can move smoothly. 5. Ensure the print gap lever “A” is set to the original position. 6. Close the printer’s top cover. When printer is in operation, ensure the printer’s top cover is closed to keep the noise level to a minimum. Notes on Ribbon Cartridge Removal: 1. Eject any paper loaded in the printer. 2. Turn off the printer power. 3. Open and remove the top cover. 4. Lift up the tear bar. 5. Set the gap lever to the most open position labeled “RIBBON”. 6. Move the carriage to the middle. Be careful not to touch the print head if printing had just been performed, as the print head may be hot. 7. Remove the blue ribbon frame from the print head. 8. Use fingers to take hold of the handle on the ribbon cartridge firmly, and lift the cartridge upwards to unlatch it. Some force may be needed to unlatch the cartridge.
Tally Dascom 1125 5Install the Single Sheet Feeder Install the single sheet feeder into the rear of the printer. Connecting the Interface Cable The 36-pin Centronics parallel, 25-pin serial RS-232C and USB ports are located at the rear of the printer. IMPORTANT: Make sure the printer and the computer are switched off before connecting or disconnecting the interface cable to prevent electrical damage to the interface ports.
Tally Dascom 1125 6Connecting the Mains Power Checking the printer voltage Make sure that the device has been set according to your country’s power supply voltage. To do this, check the rating plate at the back of the printer. Contact your dealer if the setting is incorrect. Never switch on the printer if the voltage setting is incorrect; this may result in electrical damage to the printer. Make sure that the power switch “A”, located to the right side of the printer, is in the “O” (off) position. Connect the power cord to the power inlet of the printer. Connect the power cord plug to a mains socket. Switch on the printer.
Tally Dascom 1125 7Installing the Windows Driver (Windows 2000/2003/2008 Server/XP/Vista/7) 1. Your printer CDROM comes with Windows drivers. Go to the Drivers folder and run the Installer “DriverSetup.exe”. You will see the screen on the right. Click “Next” to continue. 2. A list of ports available on your system will be displayed as shown on the right. Choose the desired port to use. Click “Next” to continue. 3. Select the desired printer model as shown on the right. Click “Next” to continue.
Tally Dascom 1125 8 4. Here you can choose whether to set the driver as the system default driver, and whether you want to print the Test Page after installation is completed. If the driver had been installed before, it would be listed in the white box on the right. Select the listed driver (if any) if you want to replace it; otherwise a copy of the driver will be installed. Click “Next” to continue. 5. Click “Finish” to start the installation process. 6. If the driver is not yet Microsoft Certified, the message on the right would appear. Click “Continue Anyway”. (As we continue to expand our product portfolio, not all of our drivers may be certified yet. Please check our website www.dascom.com for the latest certified drivers.)
Tally Dascom 1125 9 7. Installation in progress. 8. After installation is completed successfully, you will see the message on the right.
Tally Dascom 1125 10 3 Paper Installation Guide The printer can handle either single sheets or continuous forms. Single sheets, also called cut sheets, include envelopes and non-continuous, multipart forms. Continuous forms include labels and multipart forms fed into the printer using the forms tractors. The printer is able to print 1~5 plies multipart paper. Do not load paper that has been folded or is damaged, wrinkled, or curled. Adjusting the Print Gap Lever The print gap lever is on the left side of the printer inside the top cover. Take care to adjust the print gap lever to a suitable position whenever you change the number of copies being printed. Using the wrong print gap may cause print head damage or paper jams. Paper type Weight (g/m2) / ply Thickness (mm) Gap lever position Single sheet 52̚100 0.06̚0.12 1PЊ2P 2-ply 40̚52 0.12̚0.14 3-ply 40̚52 0.17̚0.22 3PЊ4P 4-ply 40̚52 0.23̚0.27 5-ply 40̚52 0.28̚0.33 5P Change ribbon --- Above 0.45
Tally Dascom 1125 11 There are 2 paper feed modes: friction feed and tractor feed. Friction Feed Handling 1. Move the paper-feed lever forward to “ ” for friction feed mode. 2. Adjust the print gap lever if necessary. 3. Raise the single sheet feeder until it locks into its mounting. Align the left paper guide with the mark on the left of the single sheet feeder. Adjust the right paper guide to the width of the paper used. 4. Insert a sheet of paper. Make sure that the bottom edge of the paper engages snugly with the platen. 5. The paper should advance automatically to the print position. The printer is now ready to print in the online state.
Tally Dascom 1125 12 Tractor Feed Handling 1. Move the paper-feed lever backward to “ ” for continuous paper position. 2. Adjust the print gap lever if necessary. 3. Raise the tractor doors and fit the first 3 paper holes onto the left tractor pins. Close the left tractor door. In the same way, install the paper on the right tractor. 4. Adjust the right tractor to the width of the paper until the paper is flat. Do not stretch the paper too taut. Push the right lock lever down to secure the right tractor in place. 5. Press theǏLoad/Ejectǐkey to load the paper to the starting print position. The printer is now ready to print in the online state.
Tally Dascom 1125 13 Continuous Paper Placement 1. Place the printer on a solid base. The minimum suitable height of the solid base is 75 cm. 2. Left and right positioning: The direction of continuous paper should be parallel with the paper guide. The tolerance should be less than 3 cm. 3. Front and back positioning: The distance between the rear of printer and the wall should be more than 60 cm. To avoid paper jam, the distance between the continuous paper and the edge of desk should be 10~15 cm.
Tally Dascom 1125 14 4 Control Panel Operation There are 4 switches S1~S4 and 4 LEDs L1~L4. The meaning and application of each switch and LED are described below. LED Indicators “Power/Paper Out” LED: On: Power on Flashing: Paper out Flashing + buzzer: Paper jam “Online” LED: On: The printer is in online state and ready to receive data from the computer. Off: The printer is in offline state and cannot receive data. Flashing: The printer is in setup state and cannot receive data. “Tear Off” LEDs: Flashing: Indicates continuous paper is at tear-off position; otherwise it indicates the selected font. Control Panel Keys “Online” Key: This key switches the printer between online and offline states. Printing is stopped when the printer is switched to offline state. When printer is switched to online state again, printing will resume. When printer is offline, pressing it for 3 seconds or longer will enter the setup state. This is indicated by a beep sound and the flashing Online LED. By pressing the Online key again will exit the setup state back to offline state. “Load/Eject” Key: When paper is loaded, pressing this key will eject the paper (single sheet mode) or park the paper (continuous paper mode). When paper is not loaded, pressing this key will load the paper to the starting print position. In the setup state, this key performs a forward micro feed.
Tally Dascom 1125 15 “LF/FF” Key: Pressing this key will feed paper one line forward. By holding down this key, the printer will initially feed a few lines, then perform a form feed (continuous paper mode) or eject the form (single sheet mode). In the setup state, this key performs a reverse micro feed. “Tear Off” Key: When online, this key will move any loaded continuous paper to the tear-off position. When in setup state, this key is used to select the desired font. Table 4.1 Font Selection Label L1 State L2 State Draft Off Off Draft Condensed Off Flash Roman Off On Sans Serif On Off Courier On Flash Prestige On On Script Flash Off Others (see Menu setting) Flash ON Tear Off Flash Flash Table 4.2 Switch Top Label Bottom Label S1 Tear Off Font S2 LF/FF Micro Feed S3 Load/Eject Micro Feed S4 Online 3sec Table 4.3 LED Label L3 Power/Paper Out L4 Online
Tally Dascom 1125 16 Panel Operation There are 3 states of operation: Online, Setup and Power On. In the Online state, the keys provide the following functions: Go to Tear Off position, Line Feed/Form feed, Load/Eject, clear buffer and switch to offline state for access to Setup state. In the Setup state, the keys provide font selection and micro feed functions. To enter the Power On state, the user holds down a key or a combination of keys while powering up the printer. This state provides the following functions: Language Setup, Main Menu setup, Hex-dump, print Main Menu, access Service Menu, adjust page margins, restore factory defaults, and firmware update. The followings describe the 3 states in details. Legend: [A] = press and hold switch A {B} = press and then release switch B [A]+ {B} = press switch B while holding A
Tally Dascom 1125 17 Online State Function Name Switch Operation LED Function Description Tear Off {S1} L1, L2 flash This is valid for tractor mode only. It feeds the form to the tear-off position. After tearing off the form, printing starts on the next TOF by: xpressing S1 once, or xreceiving print data from the host. LF {S2} - Feeds a line with every press of S2. FF [S2] - By holding S2, the printer initially feeds a few lines; then feeds the form to the next TOF for rear tractor or ejects the form for cut sheets. Load/Eject {S3} - xLoad: Automatically loads the paper (according to path selection) when no paper is on the platen. xEject: For rear tractor, it retracts the form from the platen to allow users to install cut sheets. (NOTE: Users have to toggle the path selection lever.) For cut sheets, it ejects the form on the platen. Setup state [S4] > 3 secs L4 Toggles to Setup state. Indicated by flashing L4. Clear Buffer [S4]+{S1} - Clears the print buffer and beeps once when completed. Reset [S4]+[S1] for longer time - Initializes the printer to the factory default settings. Beeps 3 times when completed.
Tally Dascom 1125 18 Setup State Function Name Switch Operation LED Function Description Online state {S4} L4 Toggling to the Online state will cause the printer to go into a ready-to-print state. Any changes made in Setup state will be saved permanently. Lighting up L4 indicates the Online state. Micro Up {S3} - Feeds up in 1/360” steps until the release of S3. Micro Down {S2} - Feeds down in 1/360” steps until the release of S2. Font Select {S1} L1, L2 Refer to Table 4.1 for details.
Tally Dascom 1125 19 Power-On State Function Name Switch Operation LED Function Description Status Page / Self Test [S4] - Prints the printer settings and self-test pattern. Pressing S1 can change the font. Hex Dump [S3] L4 Beeps once to indicate going into hex dump mode: xPrints data from host in hexadecimal representation. xLights up L4. xPressing S4 suspends the printing. xWhen the hex dump has finished, pressing S4 forces the printing of the last line of data, as any line termination control code from host has no function. xPressing S1 can change the font. xSwitch off the power to terminate the hex dump. Firmware Update [S1]+[S2]+ [S3]+[S4] L1, L2, L3, L4 xAlternate flashing of L3 and L4 indicates printer is ready for firmware update. L1 and L2 are ON and OFF respectively. xWhen new firmware is being received, L3 and L4 are set to ON. L1 flashes a few times and then sets to ON. L2 flashing indicates downloading in progress. xWhen downloading is completed, the carriage returns to home position. Printer initializes normally.
Tally Dascom 1125 20 Adjust Physical Margins [S3]+[S4] L1, L2, L3, L4 xFlashing of L3. xLights up L4.and L3. xLights up L1 or L2 according to current fonts. xIncludes Adjust Fanfold Top Margin, Adjust Single Top Margin, Adjust Fanfold Left Margin, Adjust Single Left Margin and Adjust Tear-Off position Service Menu [S1]+[S2] xFlashing of L3. xLights up L4.and L3. xLights up L1 or L2 according to current fonts. xFunctions are: Vertical Alignment, Change Pin, and Endless Self-Test. Restore Factory Defaults [S2]+[S3]+[S4] L1, L2, L3, L4 xFlashing of L3 then extinguish. xLights up L4. xLights up L1 or L2 according to current fonts. xRestore Factory Defaults parameters except Change Pin, Vertical Alignment and Adjust Page Margin Parameters Menu Setup / EDS [S1] Allows for Main Menu setting changes. Please read the instructions printed on how to change settings when this mode is activated. (EDS: Electronic DIP Switch) Language Setup [S2]+[S3] Allows user to select one of the following languages: English, German, Russian, Italian, French, Spanish and Turkish. Factory default is English. Refer to Language Setup section below for details. Language Setup The panel menu can display the following languages: English, German, Russian, Italian, French, Spanish and Turkish. Factory default setting is English. To change it to another language, hold down the [LF/FF] and [Load/Eject] keys on the panel and power-on. Upon exiting the Language Setup Menu, a listing of the current configuration is printed, and this is followed by Main Menu Setup. Below is an example of changing from English to German language:
Tally Dascom 1125 21 5 Printer Setting Changes To meet your own print requirements, the printer configurations may be changed as follows: Hold down the Tear Off key while powering on the printer, release the Tear Off key when the print head starts to move. The printer will print out the current settings and then enter Main Menu setup state. Follow the instructions printed on how to make setting changes. When a new setting is saved, it is retained after the printer has been powered off. The Main Menu is grouped into 5 sub-menus: System Setup, Page Setup, Print Setup, Interface Setup and Advanced Setup. A detailed description of the sub-menus is given below. The settings in bold and italic refer to the default settings. The settings below are provided in the following order of languages: English, German, Russian, Italian, French, Spanish and Turkish. System Setup System Setup Valid Settings Function Emulation ESC/P2, IBM 2390 Plus Selects the printer emulation. This should be the same as the host printer driver. Auto CR (IBM) Yes, No Yes: LF = LF+CR; No: LF = LF (Applies to IBM emulation only) Auto LF Yes, No Yes: CR = CR+LF; No: CR = CR Print Dir Bi-Dir, Uni-Dir, Auto Auto: Text & graphics in bi-direction; double height in uni-direction. Uni-Dir: Prints everything in uni-direction. Bi-dir: Prints everything in bi-direction. Note: Top position print direction may be affected by Top Print Dir setting. Top Print Dir Bi-Dir, Uni-Dir Bi-dir: Prints top position according to Print Dir setting. Uni-dir: Prints top position in uni-direction regardless of Print Dir setting. Impact Normal, Heavy Heavy: Higher impact force for multipart printing IBM AGM Yes, No Selects the IBM graphic mode. Applies to IBM emulation only Print Setup Print Setup Valid Settings Function Font (Others) OCR-B, OCR-A, ORATOR, GOTHIC, SOUVENIR The setting here will only be active when “Font” is set to “Others” on control panel, Pitch 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Controls the characters per inch setting. Zero 0,Ø Selects slashed or no-slash zero.
Tally Dascom 1125 22 HS-Draft On, Off On: Prints High Speed Draft when Draft font is selected. Graphic Speed Normal, Fast, Ultra When printing 180x180 DPI graphics: Normal – prints in 180x180 DPI, Fast – prints in 90x180 DPI, Ultra – prints in 60x180 DPI. IBM Set 1/2 Set 1, Set 2 Selects the IBM character set. 1: Normal; 2: Extended Int'l Char Set USA, France, Germany, UK, Denmark, Sweden, Italy, Spain, Japan, Norway, Denmark II, Spain II, Latin AM, Korea, Legal 14+1 international character set selections. Code Page 1. CP 437 2. CP 737 3. CP 850 4. CP 851 5. CP 852 6. CP 857 7. CP 858 8. CP 860 9. CP 861 10. CP 863 11. CP 864 12. CP 864 Extended 13. CP 865 14. CP 866 Cyrillic 15. CP 866 Bulgaria 16. CP 1250 17. CP 1251 18. CP 1252 19. CP 1253 20. CP 1254 21. 8859-1 22. 8859-1 (SAP) 23. 8859-2 24. 8859-5 25. 8859-7 26. 8859-9 27. 8859-15 28. BRASCII 29. Abicomp National code page selections.
Tally Dascom 1125 23 30. Roman8 31. Coax/Twinax 32. New-437 33. New-Dig 850 34. Old-Code 860 35. Flarro 863 36. 865 Hebrew 37. CP 1257 38. 866 Ukraine 39. 866 Kazakhstan 40. Kamenicky 41. Mazovia 42. CP 775 43. CRO-ASCII 44. Arabic Farsi 45. Arabic Urdo 46. Greek DEC 47. Greek ELOT 928 Character Table Graphic Table, Italic Table Character table type selection. Page Setup Page Setup Valid Settings Function Line Per Inch 1, 2, 3, 4, 5, 6, 7, 8 Sets the line spacing Fanfold Form Length 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Sets the page length for tractor mode Fanfold Top Margin 0/60" … 10/60"…99/60" Sets the top margin for tractor mode. Due to mechanical tolerance, 0/60” is not guaranteed. Fanfold Bottom Margin 0/60"…10/60"...30/60" Sets the bottom margin for tractor mode. Due to mechanical tolerance, 0/60” is not guaranteed. Single Form Length 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17" Sets the page length for friction mode Single Top Margin 0/60" … 10/60"…99/60" Sets the top margin for friction mode. Due to mechanical tolerance, 0/60” is not guaranteed. Single Bottom Margin 0/60"…10/60"...30/60" Sets the bottom margin for friction mode. Due to mechanical tolerance, 0/60” is not guaranteed. Roll Paper Yes, No In friction mode, [LF/FF] will not eject the paper and feed to next page. (Assume roll paper) Perforation Skip Yes, No Skips printing on perforation area
Tally Dascom 1125 24 Auto Tear Manual, 0.5s, 1s, 2s, 3s, 4s, 5sView1s, View2s, View3s Specifies the waiting time before feeding the page to tear-off position automatically. Manual: Auto tear mode is off. View1s, View2s, View3s: After printing is completed, the printer will feed the paper until the last printed line is at the tear-off position. (Applies to tractor mode only) Interface Setup Interface Setup Valid Settings Function Interface Auto, Parallel, USB, Serial For multi-host connection. Auto: First come first served; Parallel/USB/Serial: Serves the designated host only. RAM Usage User Font, Buffer User Font: Part of RAM is used for user download characters; Buffer: Disables user character download function; uses RAM for expanded buffer size up to 68KB. I-PRIME Yes, No Yes: Host I-Prime signal resets the printer. Protocol Xon/Xoff, DTR Serial RS-232C communication protocol selection. Data Length 8, 7 Number of data bits per data byte selection. Stop Bit 1, 2 Number of stop bits per data byte selection. Parity None, Odd, Even Selects the parity check mode. Baud Rate 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 Selects the baud rate (transmission speed). Auto IF Delay 10s, 30s Determines the waiting time before receiving data from another interface. CX Bid Yes, No Yes: Sets the parallel interface of the printer to bidirectional mode (IEEE 1284, Nibble mode), e.g. for Windows Plug & Play. No: Sets the interface to compatibility mode in order to ensure reliable operation with special external boxes. Advanced Setup Advanced Setup Valid Settings Function Auto Load Manual, 0.5s, 1s, 1.5s, 2s Specifies the waiting time before loading a cut sheet automatically. Manual: Auto load mode is off. (Applies to friction mode only.) Paper Jam Prevention Yes, No Flattens paper edges by carriage movement before printing starts. Paper End Detect Yes, No Yes: Detects paper out and halts printing; otherwise, ignores paper out and continues
Tally Dascom 1125 25 printing. Form Length Ctrl Software, Ignore Ignore: Ignores form length commands Pitch Ctrl Software, Ignore Ignore: Ignores CPI commands Font Ctrl Software, Ignore Ignore: Ignores font select commands Quality Ctrl Software, Ignore Ignore: Ignores print quality commands Buzzer Yes, No Yes: Sounds buzzer on all hardware errors German (Deutsch) System Setup Valid Settings Emulation ESC/P2, IBM 2390 Plus Auto CR (IBM) Ja, Nein Auto LF Ja, Nein Druck Dir Bi-Dir, Uni-Dir, Auto Top Druck Dir Bi-Dir, Uni-Dir Anschlag Normal, Stark IBM AGM Ja, Nein Druck Setup Valid Settings Font (Andere) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Zeichenteilung 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Null 0,Ø HS-Draft An, Aus Graphikgeschw. Normal, Schnell, Ultra IBM Set ½ Set 1, Set 2 Land USA, Frankreich, Deutschland, UK, Dänemark, Schweden, Italien, Spanien, Japan, Norwegen, Dänemark II, Spanien II, Latein-Amerika, Korea, Legal Zeichensatz CP 437, CP 857… Zeichentabelle Graphik, Italic Seiten Setup Valid Settings Zeilen Pro Zoll 1, 2, 3, 4, 5, 6, 7, 8 Endlos Formularlänge 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Endlos Oberer Rand 0/60" … 10/60"…99/60" Endlos Unterer Rand 0/60"…10/60"...30/60" Einzel Formularlänge 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"Einzel Oberer Rand 0/60" … 10/60"…99/60" Einzel Unterer Rand 0/60"…10/60"...30/60" Rollenpapier Ja, Nein
Tally Dascom 1125 26 Perforationssprung Ja, Nein Abreissen Manuell, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s Schnittstellen Setup Valid Settings Schnittstelle Auto, Parallel, USB, Serial I-PRIME Ja, Nein Protokoll Xon/Xoff, DTR Datenlänge 8, 7 Stopp Bit 1, 2 Parity None, Odd, Even Baud Rate 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 Auto IF Delay 10s, 30s RAM Nutzung Ladbarer Font, Puffer CX Bid Ja, Nein Erweitertes Setup Valid Settings Auto Laden Manuell, 0.5s, 1s, 1.5s, 2s Papierstau Vorbeugung Ja, Nein Papierende Detekt Ja, Nein Formularlänge Strg Software, Ignoriere Zeichenteilung Strg Software, Ignoriere Font Strg Software, Ignoriere Qualität Strg Software, Ignoriere Summer Ja, Nein Russian (Ɋɨɫɫɢɹ) ɋɢɫɬɟɦɧɵɟ ɭɫɬɚɧɨɜɤɢ Valid Settingsɗɦɭɥɹɰɢɹ ESC/P2, IBM 2390 Plus Ⱥɜɬɨ CR (IBM) Ⱦɚ,ɇɟɬȺɜɬɨ LF Ⱦɚ,ɇɟɬɇɚɩɪɚɜɥɟɧɢɟ ɩɟɱɚɬɢ Ⱦɜɭɧɚɩɪɚɜɥɟɧɧɚɹ,Ɉɞɧɨɧɚɩɪɚɜɥɟɧɧɚɹ,Ⱥɜɬɨɇɚɩɪɚɜɥɟɧɢɟ ɩɟɱɚɬɢ ɡɚɝɥ.ɛɭɤɜ Ⱦɜɭɧɚɩɪɚɜɥɟɧɧɚɹ,Ɉɞɧɨɧɚɩɪɚɜɥɟɧɧɚɹɍɞɚɪ ɇɨɪɦɚɥɶɧɵɣ,ɋɢɥɶɧɵɣIBM AGM Ⱦɚ,ɇɟɬ ɇɚɫɬɪɨɣɤɚ ɩɟɱɚɬɢ Valid Settings Ⱦɨɩɨɥɧɢɬɟɥɶɧɵɣ ɲɪɢɮɬ OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIRɡɧɚɤɨɜ/ɞɸɣɦ 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS ɉɟɪɟɱɟɪɤɧɭɬɵɣ ɧɨɥɶ 0,Øȼɵɫɨɤɚɹ ɫɤɨɪɨɫɬɶ ȼɤɥ,ȼɵɤɥ
Tally Dascom 1125 27 ɋɤɨɪɨɫɬɶ ɝɪɚɮɢɤɢ ɇɨɪɦɚɥɶɧɚɹ,Ȼɵɫɬɪɚɹ,Ɉɱɟɧɶ ɛɵɫɬɪɚɹɋɢɦɜɨɥɵ IBM 1/2 ɍɫɬ. 1, ɍɫɬ. 2ɇɚɛɨɪ ɡɧɚɤɨɜUSA, France, Germany, UK, ¿Ûèãú, Sweden, Italy, Spain, Japan, ÈéëÝàÞãú,¿Ûèãú II, Spain II, ÆÛíãèìåÛú Ⱥɦɟɪɢɤɚ, Korea, Legal Ʉɨɞɨɜɚɹ ɬɚɛɥɢɰɚ CP 437, CP 857… Ɍɚɛɥɢɰɚ ɡɧɚɤɨɜ Ƚɪɚɮɢɤɚ,Ʉɭɪɫɢɜ ɉɚɪɚɦɟɬɪɵ ɫɬɪɚɧɢɰɵ Valid Settings ɋɬɪɨɤ ɧɚ ɞɸɣɦ 1, 2, 3, 4, 5, 6, 7, 8 Ⱦɥɢɧɚ ɮɨɪɦɵ ɞɥɹ ɧɟɩɪɟɪɵɜɧɨɣɛɭɦɚɝɢ 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Ɉɬɫɬɭɩ ɫɜɟɪɯɭ ɞɥɹ ɧɟɩɪɟɪɵɜɧɨɣɛɭɦɚɝɢ 0/60" … 10/60"…99/60" Ɉɬɫɬɭɩ ɫɧɢɡɭ ɞɥɹ ɧɟɩɪɟɪɵɜɧɨɣ ɛɭɦɚɝɢ 0/60"…10/60"...30/60"Ⱦɥɢɧɚ ɮɨɪɦɵ ɞɥɹ ɨɬɞɟɥɶɧɵɯ ɥɢɫɬɨɜ 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"Ɉɬɫɬɭɩ ɫɜɟɪɯɭ ɞɥɹ ɨɬɞɟɥɶɧɵɯ ɥɢɫɬɨɜ 0/60" … 10/60"…99/60" Ɉɬɫɬɭɩ ɫɧɢɡɭ ɞɥɹ ɨɬɞɟɥɶɧɵɯ ɥɢɫɬɨɜ 0/60"…10/60"...30/60"Ɋɭɥɨɧɧɚɹ ɛɭɦɚɝɚ Ⱦɚ,ɇɟɬɉɪɨɩɭɫɤ ɩɟɪɮɨɪɚɰɢɢ Ⱦɚ,ɇɟɬȺɜɬɨ ɩɪɨɝɨɧ Ɋɭɱɧɨɣ, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s ɍɫɬɚɧɨɜɤɢ ɢɧɬɟɪɮɟɣɫɚ Valid Settings ɂɧɬɟɪɮɟɣɫ Ⱥɜɬɨ,ɉɚɪɚɥɟɥ, USB, RS-232 ɉɚɪɚɥɟɥ.ɩɨɪɬ Ⱦɚ,ɇɟɬɉɪɨɬɨɤɨɥ RS-232 Xon/Xoff, DTRɄɨɥ-ɜɨ ɛɢɬ 8, 7 ɋɬɨɩ ɛɢɬ 1, 2 ɑɟɬɧɨɫɬɶ ɇɟɬ,ɑɟɬ,ɇɟɱɟɬɋɤɨɪɨɫɬɶ ɩɟɪɟɞɚɱɢ ɞɚɧɧɵɯ 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 ȼɪɟɦɹ ɨɠɢɞɚɧɢɹ 10s, 30s ɇɚɡɧɚɱɟɧɢɟ RAM ɉɨɥɶɡɨɜ.ɲɪɢɮɬ,ȻɭɮɟɪCX Bid Ⱦɚ,ɇɟɬ Ⱦɨɩɨɥɧɢɬɟɥɶɧɵɟ ɭɫɬɚɧɨɜɤɢ Valid Settings Ⱥɜɬɨɡɚɝɪɭɡɤɚ Ɋɭɱɧɚɹ, 0.5s, 1s, 1.5s, 2s Ⱦɚɬɱɢɤ ɞɜɢɠ.ɛɭɦɚɝɢ Ⱦɚ,ɇɟɬȾɚɬɱɢɤ ɤɨɧɰɚ ɛɭɦɚɝɢ Ⱦɚ,ɇɟɬ
Tally Dascom 1125 28 Ʉɨɧɬɨɥɶ ɞɥɢɧɵ ɮɨɪɦɵ ɉɪɨɝɪɚɦɧɵɣ,ɂɝɧɨɪ.Ʉɨɧɬɪɨɥɶ ɡɧɚɤɨɜ/ɞɸɣɦ ɉɪɨɝɪɚɦɧɵɣ,ɂɝɧɨɪ.Ʉɨɧɬɪɨɥɶ ɲɪɢɮɬɚ ɉɪɨɝɪɚɦɧɵɣ,ɂɝɧɨɪ.Ʉɨɧɬɪɨɥɶ ɤɚɱɟɫɬɜɚ ɉɪɨɝɪɚɦɧɵɣ,ɂɝɧɨɪ.Ɂɜɭɤ Ⱦɚ,ɇɟɬ Italian (Italiano) Menu Sistema Valid Settings Emulazione ESC/P2, IBM 2390 Plus Auto CR (IBM) Si, No Auto LF Si, No Direz. Stampa Bi-Dir, Uni-Dir, Auto Top Print Dir Bi-Dir, Uni-Dir Impatto Normale, Pesante IBM AGM Si, No Menù Stampa Valid Settings Fonte (Altre) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Spaziatura 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Zero 0,Ø HS-Bozza Si, No Veloc. Grafica Normale, Veloce, Ultra IBM Set 1/2 Set 1, Set 2 Set Carat. Int. USA, Francia, Germania, Regno Unito, Danimarca, Svezia, Italia, Spagna, Giappone, Norvegia, Danimarca II, Spagna II, America Latina, Korea, Legal Code Page CP 437, CP 857… Tab.Carattere Tab. Grafica, Italico Menù Pagina Valid Settings Interlinea 1, 2, 3, 4, 5, 6, 7, 8 Lungh. Mod. Continuo 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Margine Sup. Continuo 0/60" … 10/60"…99/60" Margine Inf. Continuo 0/60"…10/60"...30/60" Lunghezza Foglio 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17" Margine Sup. Foglio 0/60" … 10/60"…99/60" Margine Infer. Foglio 0/60"…10/60"...30/60" Rullo Carta Si, No Salto Perforazione Si, No Autostrappo Manuale, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s
Tally Dascom 1125 29 Menù Interfacc. Valid Settings Interfaccia Auto, Parallela, USB, Seriale I-PRIME Si, No Protocollo Xon/Xoff, DTR Lunghezza dati 8, 7 Stop Bit 1, 2 Parità No, Dispari, Pari Velocità 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 Ritardo Auto IF 10s, 30s Uso RAM Fonti utente, Memoria CX Bid Si, No Menù Avanzato Valid Settings Autocaricamento Manuale, 0.5s, 1s, 1.5s, 2s Previene Inceppamento Si, No Rileva Fine Carta Si, No Control. Lungh. Carta Software, Ignora Control. Spaziatura Software, Ignora Controllo Fonti Software, Ignora Controllo Qualità Software, Ignora Cicalino Si, No French (Français) Setup système Valid Settings Emulation ESC/P2, IBM 2390 Plus RC-Auto (IBM) Oui, Non SL-Auto Oui, Non Dir Impr. Bidir, Unidir, Auto Sup. Dir Impr. Bidir, Unidir Frappe Normal, Forte IBM AGM Oui, Non Setup impression Valid Settings Polices (Autres) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Densités caract. 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Zéro 0,Ø HS-Draft Oui, Non Vitesse graphiq. Normal, Rapide, Ultra IBM Set 1/2 Set 1, Set 2 Pays USA, France, Allemagne, Royaume-Uni, Denmark, Suède, Italie,
Tally Dascom 1125 30 Espagne, Japon, Norvège, Denmark II, Espagne II, Amerique latine, Korea, Legal Jeu de caractèr. CP 437, CP 857… Tabl.de caract. Graphque, Italique Setup page Valid Settings Lignes par pouce 1, 2, 3, 4, 5, 6, 7, 8 Papier continu Longueur formulaire 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Papier continu Bord supérieure 0/60" … 10/60"…99/60" Papier continu Bord inférieure 0/60"…10/60"...30/60" Feuille à feuille Longueur formulaire 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17" Feuille à feuille Bord supérieur 0/60" … 10/60"…99/60" Feuille à feuille Bord inférieur 0/60"…10/60"...30/60" Papier du rouleau Oui, Non Sauter la perforation Oui, Non Coupe Auto Manuel, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s Setup interface Valid Settings Interface Auto, Parallel, USB, Serial I-PRIME Oui, Non Protocole Xon/Xoff, DTR Long. de données 8, 7 Bits d’arrêt 1, 2 Parité None, Odd, Even Vitesse baud 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 Auto IF Delay 10s, 30s Utilisation RAM User Font, Buffer CX Bid Oui, Non Setup élargi Valid Settings Chargem. Autom. Manuel, 0.5s, 1s, 1.5s, 2s Prévention bourrage Qui, Non Détec.fin de pap Qui, Non Long.formul.Strg Software, Ignorer Densi.caract.Strg Software, Ignorer Police Strg Software, Ignorer Qualité Strg Software, Ignorer Vibrateur Qui, Non
Tally Dascom 1125 31 Spanish (Español) System Setup Valid Settings Emulación ESC/P2, IBM 2390 Plus Auto CR(IBM) Si, No Auto LF Si, No ModoImpresión Bi-Dir, Uni-Dir, Auto ModoImp.Borde Bi-Dir, Uni-Dir Impacto Normal, Fuerte IBM AGM Si, No Print Setup Valid Settings Fuente (Otros) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Tamaño Letra 10cpp, 12cpp, 15cpp, 17cpp, 20cpp, PS Cero 0,Ø Alta Velocidad Activado, Desactivado Imp. Grafica Normal, Rápido, Ultra IBM Juego 1/2 Juego 1, Juego 2 Carácter Local USA, Francia, Alemania, Reino Unido, Dinamarca, Suecia, Italia, España, Japón, Noruega, Dinamarca II, España II, AméricaLatina, Corea, Legal Tabla Carácter CP 437, CP 857… Tipo Tabla Tabla Gráfica, Italica Page Setup Valid Settings Lineas Por Pulgada 1, 2, 3, 4, 5, 6, 7, 8 Tamaño Papel Continuo 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Margen Sup. Pap Cont. 0/60" … 10/60"…99/60" Margen Inf. Pap.Cont. 0/60"…10/60"...30/60" Tamaño Hojas Sueltas 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17" Margen Sup. Folios 0/60" … 10/60"…99/60" Margen Inf. Folios 0/60"…10/60"...30/60" Rollo de Papel Si, No Salto perforación Si, No Mover a PosiciónCorte Manual, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s Interface Setup Valid Settings Interface Auto, Paralelo, USB, Serie I-Prime Si, No
Tally Dascom 1125 32 Protocolo Xon/Xoff, DTR LongitudDatos 8, 7 Bit Parada 1, 2 Paridad Ninguna, Impar, Par Tasa Baudios 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 Auto retraso 10s, 30s Uso de RAM Font Usuario, Buffer CX Bid Si, No Advanced Setup Valid Settings Auto Carga Manual, 0.5s, 1s, 1.5s, 2s Prevención Atascos Si, No Detección Fin Papel Si, No Control Tamaño Papel Software, Ignorar Control Tamaño Letra Software, Ignorar Control Fuente Software, Ignorar Control Calidad Software, Ignorar Alarma Si, No Turkish (Türkce) Sistem Ayarı Valid Settings Benzetim/Emulation ESC/P2, IBM 2390 Plus Otom. Satırbaġı (IBM) Evet, Hayır Otom. Satır besleme Evet, Hayır Yazdırma yönü òki-Yöne, Tek-Yöne, Otom. Üstte yazdırma yönü òki-Yöne, Tek-Yöne Vuruġ Normal, Güçlü IBM AGM Evet, Hayır Yazdırma Ayarları Valid Settings Yazı Tipi (Diáer) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Karakter Sıklıáı 10cpi, 12cpi, 15cpi, 17cpi, 20cpi, PS Sıfır 0,Ø Yük.Hız-Taslak On, Off Grafik Hızı Normal, Hızlı, Ultra IBM Karakter Seti 1/2 Set 1, Set 2 Uluslararası Kar. Seti Amerika Bir.Devleti, Fransa, Almanya, øngiltere, Danimarka, øsveç, øtalya, øspanya, Japonya, Norveç, Danimarka II, øspanyaII, Latin Amerika, Korea, Legal Kod Sayfası CP 437, CP 857…
Tally Dascom 1125 33 Karakter Tablosu Grafik Tablosu, òtalik Sayfa Düzeni Ayarı Valid Settings ònç baġına satır 1, 2, 3, 4, 5, 6, 7, 8 Sürekli-kaáıt Form Uzunluáu 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Sürekli-kaáıt Üst kenar boġluáu 0/60" … 10/60"…99/60" Sürekli-kaáıt Alt kenar boġluáu 0/60"…10/60"...30/60" Tek-kaáıt Form uzunluáu 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"Tek-kaáıt Üst kenar boġluáu 0/60" … 10/60"…99/60" Tek-kaáıt Alt kenar boġluáu 0/60"…10/60"...30/60" Rulo kaáıt Evet, Hayır Delik atlama Evet, Hayır Otom. Koparma Elle/Manuel, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s Arabirim Ayarları Valid Settings Arabirim Otom., Paralel, USB, Seri I-Prime Evet, Hayır òletiġim Kuralları Xon/Xoff, DTR Veri Uzunluáu 8, 7 Durma Biti 1,2 Eġlik Yok, Çift, Tek Baud Hızı 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 Otom. Arabirim gecikmesi 10s, 30s RAM Kullanımı Kullanıcı Yazı Tipi, Arabellek CX Bid Evet, Hayır Geliġtirilmiġ Ayarlar Valid Settings Otom. Yükleme Elle/Manuel, 0.5s, 1s, 1.5s, 2s Kaáıt Sıkıġmasını Önleme Evet, Hayır Kaáıt Sonunu Algılama Evet, Hayır Form Uzunl. Kont. Yazılım, Yoksay Karak.Sıkl. Kont. Yazılım, Yoksay Yazı Tipi Kont. Yazılım, Yoksay Kalite Kont. Yazılım, Yoksay Alarm Zili Evet, Hayır
Tally Dascom 1125 34 Vertical Alignment The vertical alignment function is used to resolve any vertical line misalignments in bi-directional printing. Adjust Vertical Alignment Procedure: 1. Enter the Service Menu by holding down theɋTear/OffɌandɋLF/FFɌkeys while powering up. 2. Load paper. 3. The printer will print as follows: Service Menu ɋLF/FFɌ= OK ɋTear/OffɌ= Back ɋLoad/EjectɌ= Next ɋOnlineɌ= Exit Current SettingφVertical Alignment 4. PressɋLF/FFɌkey to select the current setting. The printer will print as follows: Vertical Alignment ɋLF/FFɌ= OK ɋTear/OffɌ= Back ɋLoad/EjectɌ= Next ɋOnlineɌ= Exit Please select Paper TypeφSingle Ply For single ply paper, pressɋLF/FFɌkey to select. For multipart paper, press ɋLoad/EjectɌkey to go to “Multipart”ˈthen pressɋLF/FFɌkey to select. 5. If single ply is selected for paper type, the following will print: Single Ply Current Print Mode: LQ Press ɋLoad/EjectɌkey to scroll to other print modes if required. 6. If LQ is selected, the following will print: LQ ɋLF/FFɌ= lower ½ to left ɋLoad/EjectɌ= lower ½ to right ɋOnlineɌ= Exit LQ -2: |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| Pressing ǏLF/FFǐor ǏLoad/Ejectǐ key will allow you to adjust the alignment of the vertical lines
Tally Dascom 1125 35 printed above. 7. Once the setting which gives the best alignment is found, press ɋOnlineɌ key to exit current level. Printer will print “Save settings? Yes”. Press ɋLF/FFɌ key to save setting. Press ǏOnlineǐ key a few times until the printer exits the Service Menu. Change Pin Function When printer has been used for a long time or the print volume is high, the frequently used print head pins may fail. The Change Pin function enables the user to continue using the printer for a while without compromise in print quality until a suitable print head replacement is available. This function will reduce the print speed if activated. Change Pin Procedure: 1. Enter the Service Menu by holding down theɋTear/OffɌandɋLF/FFɌkeys while powering up. 2. Load paper. 3. The printer will print as below: Service Menu ɋLF/FFɌ=OK ɋTear/OffɌ= Back ɋLoad/EjectɌ= Next ɋOnlineɌ= Exit Current MenuφVertical Alignment Press ǏLoad/Ejectǐ key to scroll to “Change Pin”ˈthen press ɋLF/FFɌ key to select. The status of each pin will be printed as follows: Change Pin 1 ---------- Is this pin OK? Yes / No 2 ---------- Is this pin OK? Yes / No 3 ---------- Is this pin OK? Yes / No : 24 ---------- Is this pin OK? Yes / No Press ɋLoad/EjectɌ key to choose whether the pin is Ye s or Noˈthen press ɋLF/FFɌ key to confirm selection. 4. When all the 24 pins are evaluated, press ɋOnlineɌ. The printer will print “Save settings? Yes”. Press ɋLF/FFɌ key to confirm selection. Press ǏOnlineǐ key a few times until the printer exits the Service Menu.
Tally Dascom 1125 36 Adjust Physical Margins Adjust Page Margins allows for adjustments of physical left, top margins and tear-off position. Warning: Once these settings are changed, resetting the printer to factory defaults will not initialize these settings back to the original settings; so it is not advisable to perform this adjustment unless it is absolutely necessary. Adjust Top Margin Procedure: 1. Enter the Adjust Page Margins function by holding down theɋLoad/EjectɌandɋOnlineɌkeys while powering up until the printer beeps twice. 2. Load paper. 3. The printer will print as below: Adjust Page Margins: ɋLF/FFɌ=OK ɋTear/OffɌ= Back ɋLoad/EjectɌ= Next ɋOnlineɌ= Exit Current Setting: Adjust Fanfold Top Margin PressǏLF/FFǐkey to confirm selection if the paper used is fanfold type. The printer will print as follows: Procedure˖ Install fanfold paper to tractors ǏLF/FFǐ = Add ǏLoad/Ejectǐ = Reduce ǏOnlineǐ = Exit Each step is 0.5 mm Function of keys: ǏTe a r O f fǐkey: Decrease 0.5mm ǏLoad/Ejectǐkey: Increase 0.5mm 4. Press ǏLF/FFǐ key, printer will print “Save settings˛Ye s ”. Press ǏLoad/Ejectǐ key to choose Yes or Noˈthen press ǏLF/FFǐ key to confirm selection and exit “Adjust Page Margins” mode by pressing ǏOnlineǐ. The print head moves to the left side and the printer beeps twice, then the print head moves to the middle position. Adjust Left Margin Procedure: 1. Enter the Adjust Page Margins function by holding down theɋLoad/EjectɌandɋOnlineɌkeys while powering up until the printer beeps twice. 2. Load paper. 3. The printer will print as below: Adjust Page Margins: ɋLF/FFɌ=OK ɋTear/OffɌ= Back ɋLoad/EjectɌ= Next ɋOnlineɌ= Exit Current Setting: Adjust Fanfold Top Margin 4. PressǏLoad/Ejectǐkey until the current setting is “Adjust Fanfold Left Margin”. PressǏLF/FFǐkey to confirm selection if the paper used is fanfold type. The printer will print as follows: Adjust Fanfold Left Margin 0
Tally Dascom 1125 37 Function of keys: ǏTe a r O f fǐkey: Decrease 0.5mm ǏLoad/Ejectǐkey: Increase 0.5mm 5. Press ǏLF/FFǐ key, printer will print “Save settings˛Ye s ”. Press ǏLoad/Ejectǐ key to choose Yes or Noˈthen press ǏLF/FFǐ key to confirm selection and exit “Adjust Page Margins” mode by pressing ǏOnlineǐ. The print head moves to the left side and the printer beeps twice, then the print head moves to the middle position. Adjust Tear-Off Position Procedure: 1. Enter the Adjust Page Margins function by holding down theɋLoad/EjectɌandɋOnlineɌkeys while powering up until the printer beeps twice. 2. Load fanfold paper. 3. The printer will print as below: Adjust Page Margins: ɋLF/FFɌ=OK ɋTear/OffɌ= Back ɋLoad/EjectɌ= Next ɋOnlineɌ= Exit Current Setting: Adjust Fanfold Top Margin 4. PressǏLoad/Ejectǐkey until the current setting is “Adjust Tear-Off Position”. PressǏLF/FFǐkey to confirm selection. The printer will print as follows: Procedure˖ Install fanfold paper to tractors ǏLF/FFǐ = Add ǏLoad/Ejectǐ = Reduce ǏOnlineǐ = Exit Each step is 0.5 mm Function of keys: ǏTe a r O f fǐkey: Decrease 0.5mm ǏLoad/Ejectǐkey: Increase 0.5mm 5. Press ǏLF/FFǐ key, printer will print “Save settings˛Ye s ”. Press ǏLoad/Ejectǐ key to choose Yes or Noˈthen press ǏLF/FFǐ key to confirm selection and exit “Adjust Page Margins” mode by pressing ǏOnlineǐ. The print head moves to the left side and the printer beeps twice, then the print head moves to the middle position.
Tally Dascom 1125 38 Dascom Printer Setup Tool In the CDROM is a software utility called “Dascom Printer Setup”. This application enables a convenient, simple and fast way to control your printer without touching any keys on the operation panel. 1. Start the tool installation by double clicking the “Dascom Printer Setup.exe”. 2. Connect the printer to the system using USB cable 3. Power up the printer. 4. Load paper into the printer. (Note: The tool cannot get connected to the printer when the printer is offline.) 5. Run the tool from the Windows Start menu by selecting All Programs, then Dascom Printer Setup, and then Tally Dascom Printer Setup. 6. For more information on how to use the tool, go to the Help menu and select User Guide.
Tally Dascom 1125 39 6 Maintenance Your printer requires very little care. Occasional cleaning and replacement of the ribbon cartridge are all that is required. Cleaning is recommended approximately every 6 months or 300 hours of operation, whichever is sooner. Lubrication of the printer is not usually necessary. If the print head carriage does not move smoothly back and forth, clean the printer in the manner described in this chapter. If the problem continues, contact your dealer to determine whether lubrication may be necessary. Switch printer off and unplug the power cord from the mains before doing any maintenance work. Cleaning The housing and the top cover of the printer help protect it against dust, dirt, and other contaminants. However, paper produces small particles that accumulate inside the printer. This section explains how to clean and vacuum the printer and how to clean the paper bail rollers. It is easier to clean the printer when the cover is open. Cleaning and Vacuuming the Printer If the print head carriage does not move smoothly back and forth or paper particles have accumulated in the printer, clean the printer. To clean and vacuum the printer: 1. Remove any paper from the printer. Make sure that the power is off, and then disconnect the printer power cord. 2. Using a soft vacuum brush, vacuum the exterior of the printer. Also vacuum the cut sheet edge. 3. Use a soft, damp cloth to wipe the exterior of the printer, including the cover. A mild detergent may be used. Do not use solvents, kerosene, or abrasive cleaning materials that may damage the printer. 4. Open the cover of the printer and remove the ribbon cartridge. Using a soft vacuum brush, gently vacuum the platen, the print head carriage and shaft, and surrounding areas. You can easily slide the print head to the left or right when the power is off. Be careful not to press too hard on the flat head cable that extends from the print head carriage. 5. Re-install the ribbon cartridge. 6. Remove the single sheet feeder and clean the form tractors and the surrounding areas. 7. Re-install the single sheet feeder. Cleaning the Paper Rollers Clean the platen and paper bail rollers occasionally or when stains or smudges appear on the paper. Use a mild detergent as appropriate. Do not use alcohol to clean the platen or the rollers. Alcohol may cause the rubber to harden. To clean the rollers and the platen: 1. Apply a small amount of water to a soft cloth. Avoid spilling liquid inside the printer. 2. Place the cloth against the platen and manually rotate the paper feed knob. 3. Repeat this procedure for each roller.
Tally Dascom 1125 40 4. To dry the platen, place a dry cloth against the platen and the rollers and manually rotate the paper feed knob.
Tally Dascom 1125 41 7 Troubleshooting Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you cannot resolve, contact your dealer or service partner for assistance. Print Quality Problems and Solutions Problem Solution Printing is too light or too dark. • Make sure that the ribbon cartridge is properly installed and that the ribbon feeds smoothly. • Replace the ribbon if necessary. • Make sure that the print gap lever is set for the thickness of your paper. Smears and stains appear on the page. • Make sure that the print gap lever is set for the thickness of your paper. • Check for ribbon wear. Replace the ribbon if necessary. • Check whether the tip of the print head is dirty. Clean the head with a soft cloth if necessary. • The print head may need to be replaced. Printing is erratic or the wrong characters are printed. Many “?” or unexpected characters are printed. • Make sure that the interface cable is securely connected to both the printer and computer. • Make sure that the printer driver selected in your software is the same as the emulation selected on the printer. • Check the length of the interface cable. (Maximum Parallel & USB: 2 meters, Serial: 15 meters) • Try another interface cable. The page is blank. • Make sure that the ribbon cartridge is properly installed. • Make sure the gap lever is set correctly. Printing is vertically misaligned (jagged). Use the printer's vertical alignment function to check the vertical print alignment. If necessary, adjust the print alignment. The top margin is wrong. • Check the application top margin setting. • Adjust the Top Margin setting in Page Setup menu if necessary. Lines are double spaced instead of single spaced. Change the Auto LF setting in the System Setup menu to No. The printer overprints on the same line. Change the Auto CR setting in the System Setup menu to No. The next print line starts where the previous line ended instead of at the left margin. Change the Auto CR setting in the System Setup menu to Yes.
Tally Dascom 1125 42 Paper Handling Problems and Solutions Problem Solution Paper cannot be loaded or fed. • Make sure that the paper select lever located on the top right of the printer is set correctly. Move the lever to the front for single sheets or to the rear for continuous forms. • Make sure that the paper covers the paper-out sensor. Paper jams while loading. • Turn off the printer and remove the jammed paper. Remove any obstructions from the paper path. • Make sure that the Print Gap lever is set for the thickness of your paper. • Make sure that the paper is not folded, creased, or torn. • Make sure that the left and right tractors are set so that the continuous forms are stretched taut. Paper jams while printing. • Turn off the printer and remove the jammed paper. Remove any obstructions from the paper path. • Make sure that the Print Gap lever is set for the thickness of your paper. • For continuous forms, make sure that the incoming and outgoing paper stacks are correctly placed. Paper should feed straight. Paper slips off the forms tractors or the perforated holes of the paper tear during printing. Make sure that the forms tractors are positioned correctly for the width of your paper and that the perforated holes of the paper fit directly over the tractor pins. Operating Problems and Solutions Problem Solution The power does not turn on. • Check whether the mains voltage is correct. • Make sure that the power cord is securely connected to both the printer and the mains power outlet. • Make sure that the power outlet is functional. If not so, use other outlet. • Turn the power off. Wait a minute and then turn the printer on again. If the printer still has no power, contact your dealer.
Tally Dascom 1125 43 The printer is on but it will not print. • Make sure that the Online indicator is lit. • If you use the interface cable, make sure it is securely connected to both the printer and the computer. • Make sure paper is loaded. • Run the printer Status Page. If printing executes normally, the problem is caused by: the interface, the computer, incorrect printer settings, or incorrect software settings. • Make sure that the printer driver selected in your software is the same as the emulation selected on the printer. Paper select lever error If paper is loaded and the paper select lever is moved to the incorrect position, the printer turns offline, and the buzzer sounds continuously. Switch the paper select lever back to its correct position. Printer Failures A user cannot generally resolve a problem involving defective printer hardware. Power off and on again the printer to recover any fatal error. If the problem cannot be resolved, contact your dealer or service partner. Error Indications on LEDs Error Description OperationStatus Paper Out LED Online LED Tear Off LED Buzzer Sound Paper out Normal Flash Off No change Once Paper jammed Suspend Flash Off Flash Once Friction feed /Tractor feed Suspend On Off Flash Continuously Print head hot Normal On Flash No change -- Carriage initial position Stop Off Off Flash Once Memory Stop Off Off Flash -- EEPROM Normal Off Flash No change Once CMOS chip Stop Off Flash Flash --
Tally Dascom 1125 44 Diagnostic Functions The printer diagnostic functions are Self-Test page, hex-dump mode and print alignment adjustment. xSelf-Test page: Tells you whether the printer hardware is functioning correctly. If the printer hardware is functional, any problems you are having are probably caused by incorrect printer settings, incorrect software settings, the interface, or the computer. xHEX-DUMP MODE: Allows you to determine whether the computer is sending the correct commands to the printer, and whether the printer is executing the commands correctly. This function is useful to programmers or others who understand how to interpret hex dumps. xPRINTING ALIGNMENT ADJUSTMENT: Allows you to check and, if necessary, correct the printer’s vertical line print alignment in bi-directional mode. For details on using these functions, please refer to chapters 4 and 5.
Tally Dascom 1125 45 Firmware Update Sometimes it is necessary update the firmware to solve a problem. The latest firmware file may be obtained from your dealer or downloaded from our website www.dascom.com. Before upgrading firmware, it is strongly recommended to print the Main Menu page to keep a record of the old settings. Note: Firmware update should only be performed by an authorized service person. We disclaim any responsibility for any damage caused if it is performed by any other person. To load new firmware, proceed as follows: 1. Switch off the printer. Connect your PC to the parallel port on the printer. 2. Press and hold down all 4 keys (S1, S2, S3, S4) while powering on the printer. 3. Alternate flashing of L3 and L4 LEDs indicates printer is ready for firmware update. L1 and L2 LEDs are ON and OFF respectively. 4. Go to the DOS prompt window. Copy the firmware file (with extension .MOT) to your printer as follows: COPY /B <filename>.mot PRN 5. When new firmware is being received, L3 and L4 LEDs are set to ON. L1 LED flashes a few times, then sets to ON. L2 LED flashing indicates downloading in progress. Note: Do not interrupt the downloading process to prevent possible flash memory corruption. 6. When downloading is completed, the carriage returns to home position. Printer initializes normally. Alternatively, you can use the Firmware Flash Tool version 3.5 or higher which is available in the CDROM and our website as well. Upon starting up the tool, choose the correct file and press "Update".
Tally Dascom 1125 46 8 General Specifications Print System Mono-chrome serial impact dot matrix Print Technology Uni-/bi-directional logic seeking for text and graphics Print Speed Pitch HS Draft Draft LQ (CPS/DPI) 10 CPI 375/80H 250/120H 83/360H 12 CPI 300/120H 300/120H 100/360H 15 CPI 375/120H 375/120H 125/360H 17.1 CPI 426/120H 426/120H 142/360H 20 CPI 498/120H 498/120H 166/360H Font Matrix Pitch HS Draft Draft LQ (Matrix/DPI) 10 CPI 8x24/80H 12x24/120H 36x24/360H 12 CPI 10x24/120H 10x24/120H 30x24/360H 15 CPI 8x16/120H 8x16/120H 24x16/360H 17.1 CPI 7x24/120H 7x24/120H 21x24/360H 20 CPI 6x24/120H 6x24/120H 18x24/360H Proportional Nx24/360H Nx24/360H Nx24/360H Print Head Number of pins: 24 pins Firing frequency: Normal mode: 1500 Hz Pin diameter: 0.2 mm Life: 400 million strokes/pin @ Draft mode Graphics 8-bit mode: 8V x 60H, 80H, 90H, 120H, 240H (DPI) 24-bit mode: 24V x 60H, 90H, 120H, 180H, 360H (DPI) Paper Feed Speed Continuous feed: 5.0 IPS (inches per second) Resolution 360 x 360 DPI maximum Printable Columns Characters per line (CPL) 10 CPI: 80 CPL 12 CPI: 96 CPL 15 CPI: 120 CPL 17.1 CPI: 137 CPL 20 CPI: 160 CPL
Tally Dascom 1125 47 Built-In Fonts Bitmap Fonts: 1. Draft 10, 12, 15, 17, 20 CPI 2. Roman 10, 12, 15, 17, 20 CPI, Proportional 3. Sans Serif 10, 12, 15, 17, 20 CPI, Proportional 4. Courier 10, 12, 15, 17, 20 CPI, Proportional 5. Prestige 10, 12, 15, 17, 20 CPI 6. OCR-B 10, 12, 17, 20 CPI 7. OCR-A 10, 12, 17, 20 CPI 8. Orator 10, 12, 15, 17, 20 CPI, Proportional 9. SOUVENIR 10, 12, 15, 17, 20 CPI, Proportional 10. GOTHIC 10, 12, 15, 17, 20 CPI, Proportional 11. Script 10, 12, 15, 17, 20 CPI Barcodes 1. EAN-13 2. EAN-8 3. Interleaved 2 of 5 4. UPC-A 5. UPC-E 6. Code 39 7. Code 128 8. POSTNET 9. Codabar 10. Industrial 2 of 5 Code Pages 1. CP 437 2. CP 737 3. CP 850 4. CP 851 5. CP 852 6. CP 857 7. CP 858 8. CP 860 9. CP 861 10. CP 863 11. CP 864 12. CP 864 Extended 13. CP 865 14. CP 866 Cyrillic 15. CP 866 Bulgaria 16. CP 1250 17. CP 1251 18. CP 1252 19. CP 1253 20. CP 1254
Tally Dascom 1125 48 Code Pages 21. 8859-1 22. 8859-1 (SAP) 23. 8859-2 24. 8859-5 25. 8859-7 26. 8859-9 27. 8859-15 28. BRASCII 29. Abicomp 30. Roman8 31. Coax/Twinax 32. New-437 33. New-Dig 850 34. Old-Code 860 35. Flarro 863 36. 865 Hebrew 37. CP 1257 38. 866 Ukraine 39. 866 Kazakhstan 40. Kamenicky 41. Mazovia 42. CP 775 43. CRO-ASCII 44. Arabic Farsi 45. Arabic Urdo 46. Greek DEC 47. Greek ELOT 928 International Character Sets 1. USA 2. France 3. Germany 4. UK 5. Denmark I 6. Sweden 7. Italy 8. Spain I 9. Japan 10. Norway 11. Denmark II 12. Spain II 13. Latin America 14. Korea 15. Legal
Tally Dascom 1125 49 Line Spacing 1/6", 1/8", n/60", n/180", n/360" Paper Specifications Paper Specifications Cut Sheet Fanfold Paper Single ply Multi-part Width: 76.2mm̚256.5mm ˄3"̚10.1"˅ Length: 101.6mm̚363.2mm ˄3.9"̚14.3"˅ Width: 76.2mm̚254mm (3"̚10"˅ Length: 101.6mm min (4" min) Weight: 52̚100g/΃ Thickness: 0.065̚0.14mm (0.0026"̚0.0055”) Weight: 52̚100 g/΃ Thickness: 0.065̚0.14mm (0.0026"̚0.0055") Weight: 40̚58g/΃ Thickness: 0.45 mm max (0.0177” max) Paper Handling Feeding method: Friction and Tractor Paper path: Cut sheets: Top load and top out Fanfold: Rear in and top out Copy Capability Original + 4 copies Emulation ESC/P2, IBM 2390 Plus Ribbon Type Cartridge; Monochrome Ribbon Life 7 million characters (rolling Draft 10 CPI) Input Data Buffer Up to 68KB Windows Drivers Windows Server 2000/2003/2008 Windows Vista Windows XP Windows 98 Windows 7 Interface Parallel (Bi-directional IEEE-1284 nibble mode) USB 2.0 (B type connector) Serial RS-232C Operation Panel Switches: 4 pcs LED indicators: 4 pcs Noise Level < 51 dBA in 10CPI draft ASCII (Conforming to ISO7779) Ambient Conditions Temperature Operating: +5 to +40 °C. Stand-by: -20 to +55 °C Humidity Operating: 10 to 80%RH (No condensation) Stand-by: 5 to 85%RH (No condensation) Dimensions 359 mm (W) x 285 mm (D) x 159 mm (H)
Tally Dascom 1125 50 Weight 5 kg Power Supply Unit type: Switching mode power supply Power cord: Detachable Voltage rating: AC 230V (180V~264V), 50Hz to 60Hz AC 110V/120V, 60Hz (factory option) Stand by: Less than 3.8W ESD: Comply with IEC801-2 Contact discharge: 4kV Air discharge: 8kV Power consumption 28.2 W (standard ECMA-132) MTTR < 20 minutes MTBF 10000 hours @ 25% duty cycle Certification CE, UL, FCC, ES, ISTA, RoHS, WEEE, REACH, ChemVerbotsV, Microsoft Certified for Windows 7
Tally Dascom 1125 51 9 Interfaces Parallel Interface Parallel Interface Pin Assignment Pin Signal Name Signal Tr a n s m i s s i o n 1 STROBE¯¯¯¯¯¯ Printer I Computer 2~9 DATA Printer I Computer 10 ACK¯¯¯ Printer J Computer 11 BUSY Printer J Computer 12 PE Printer J Computer 13 SELECT Printer J Computer 14 AFXT¯¯¯¯ Printer I Computer 15 Unused Unused 16 GND Printer Q Computer 17 F-GND Printer Q Computer 18 +5V Printer J Computer 19~30 GND Printer Q Computer 31 INIT¯¯¯¯ Printer I Computer 32 FAULT¯¯¯¯¯ Printer J Computer 33 GND Printer Q Computer 34 Unused Unused 35 FUSE Printer J Computer 36 SLCTIN¯¯¯¯¯¯ Printer I Computer Parallel Interface Connector Diagram Note: Any external devices connected to the parallel port should not draw current exceeding 200 mA from pin 18; otherwise it may affect the printer operation.
Tally Dascom 1125 52 USB Interface The USB interface conforms to the Universal Serial Bus 2.0 Specifications. It supports the Full Speed mode at 12 Mbps. It uses the “B” type USB connector. Serial Interface Serial RS-232C Interface Pin Assignment Pin Signal Symbol Signal Name Signal Transmission 1 CG Chassis Ground — 2 TXD Send Data OUT 3 RXD Receive Data IN 4 RTS Request to Send OUT 7 SG Signal Ground — 20 DTR Data Terminal Ready OUT 25 +5V Power — Serial RS-232 Connector Diagram
Tally Dascom 1125 53 10 Character sets & Code Pages Character Sets Standard Character Set 1 Standard Character Set 2
Tally Dascom 1125 54 IBM Character Set 1 IBM Character Set 2
Tally Dascom 1125 55 International character sets International Character Set Commands Country Command USA ˘ESC˚“R”CHRˀ˄0˅ France ˘ESC˚“R”CHRˀ˄1˅ Germany ˘ESC˚“R”CHRˀ˄2˅ UK ˘ESC˚“R”CHRˀ˄3˅ Denmark1 ˘ESC˚“R”CHRˀ˄4˅ Sweden ˘ESC˚“R”CHRˀ˄5˅ Italy ˘ESC˚“R”CHRˀ˄6˅ Spain1 ˘ESC˚“R”CHRˀ˄7˅ Japan ˘ESC˚“R”CHRˀ˄8˅ Norway ˘ESC˚“R”CHRˀ˄9˅ Denmark2 ˘ESC˚“R”CHRˀ˄10˅ Spain2 ˘ESC˚“R”CHRˀ˄11˅ Lat America ˘ESC˚“R”CHRˀ˄12˅ Korea ˘ESC˚“R”CHRˀ˄13˅ Legal ˘ESC˚“R”CHRˀ˄64˅
Tally Dascom 1125 56 Character Tables Italic
Tally Dascom 1125 57 Graphic 1 Graphic 2
Tally Dascom 1125 58 Code Page Commands Code Page ESC R Parameter CRO-ASCII 3C Arabic Farsi 96 Arabic Urdo 97 Greek DEC 46 Greek ELOT 928 6C CP437 Latin US 80 CP737 Greek 93 CP850 Latin 1 82 CP851 Greek 88 CP852 Latin 2 87 CP857 Turkish 8D CP858 (IBM with €) 9E CP860 Portugal 84 CP861 Icelandic 94 CP863 French Canada 85 CP864 Arabic 8C CP864 Arab. Extended 95 CP865 Nordic 86 CP866 Cyrillic 8E CP866 Bulgaria 9D Siemens Turkish 9B DEC Turkish 9C CP1250 Win Latin 2 70 CP1251 Win Cyrillic 71 CP1252 Win Latin 1 72 CP1253 Win Greek 73 CP1254 Win Turkish 74 8859-1 Latin 1 25 8859-1 Latin 1 (SAP) 2B 8859-2 Latin 2 26 8859-5 Cyrillic 2A 8859-7 Greek 2D 8859-9 Turkish 2E 8859-15 Latin 9 (Euro) 2F BRASCII 6D Abicomp 6E Roman 8 4D
Tally Dascom 1125 59 Coax/Twinax(Hebrew) 4F New-437 (Hebrew) 81 New-DIG 850 (Hebr.) 83 Old-Code 860 (Hebr.) 98 Flarro 863 (Hebrew) 99 Table 865 (Hebrew) 9A CP775 Baltic A6 CP1257 Baltic 77 Mazovia (Poland) 92 Kamenicky (Czech) 91 CP866 Ukraine 8F CP866 Kazakhstan 90
Tally Dascom 1125 60 Code Page Tables CP 437 (US) CP 737 Greek
Tally Dascom 1125 61 CP 850 (Multilingual) CP 851
Tally Dascom 1125 62 CP 852 (Eastern Europe) CP 857 (Turkish)
Tally Dascom 1125 63 CP 858 CP 860 (Portugal)
Tally Dascom 1125 64 CP 861 (Iceland) CP 863 (French-Canadian)
Tally Dascom 1125 65 CP 864 Arabic CP 864 Arabic Extended
Tally Dascom 1125 66 CP 865 (Norway) CP 866 (Cyrillic)
Tally Dascom 1125 67 CP 866 Bulgaria CP 1250 Win Latin 2
Tally Dascom 1125 68 CP 1251 Win Cyrillic CP 1252 Win Latin 1
Tally Dascom 1125 69 CP 1253 Win Greek CP 1254 Win Turkish
Tally Dascom 1125 70 8859-1 Latin 1 8859-1 Latin 1 (SAP)
Tally Dascom 1125 71 ISO 8859-2 (ISO Latin 2) ISO 8859-5 Cyrillic
Tally Dascom 1125 72 ISO 8859-7 (Latin/Greek) ISO 8859-9 (Turkish)
Tally Dascom 1125 73 ISO 8859-15 Euro (Code Page 923) BRASCII
Tally Dascom 1125 74 Abicomp Roman 8
Tally Dascom 1125 75 Coax/Twinax (Hebrew) New-437 (Hebrew)
Tally Dascom 1125 76 New-Dig 850 (Hebrew) Old-Code 860 (Hebrew)
Tally Dascom 1125 77 Flarro 863 (Hebrew) 865 Hebrew
Tally Dascom 1125 78 CP 1257 866 Ukraine
Tally Dascom 1125 79 866 Kazakhstan Kamenicky
Tally Dascom 1125 80 Mazovia CP 775
Tally Dascom 1125 81 CRO-ASCII Arabic Farsi
Tally Dascom 1125 82 Arabic Urdo Greek DEC
Tally Dascom 1125 83 Greek ELOT 928
Tally Dascom 1125 84 11 Control Codes Summary Epson Emulation Command List Command Sequence Function BEL Beeper BS Backspace HT Tab horizontally LF Line feed VT Tab vertically FF Form feed CR Carriage return SO Select double-width printing (one line) SI Select condensed mode DC1 Online DC2 Cancel condensed mode DC3 Offline DC4 Cancel double-wide mode(one line) CAN Cancel line DEL Delete character ESC SO Select double-width printing (one line) ESC SI Select condensed mode ESC SP n Set intercharacter space ESC EM n NA ESC ! n Print mode setup ESC ( - n1 n2 m d1 d2 Choose character lineation ESC $ n1 n2 Select absolute horizontal print position ESC | n Set left margin ESC % n Select user-defined set ESC & Define user-defined set ESC ( ^ n m d1 d2… Print data in character style ESC (G NUL d Select graphics mode ESC * m n1 n2… Select image mode ESC . c v h m nL nH d1 d2… Print raster graphics ESC + n Select n/360Ǝline spacing ESC – n Underline on/off ESC / n Select vertical orientation channel ESC ( C NUL n m Set page length ESC ( c NUL nt mt nb mb Page setup ESC ( U NUL n Set unit ESC 0 Set 1/8Ǝline spacing ESC 2 Set 1/6Ǝline spacing ESC 3 n Set n/180Ǝline spacing ESC 4 Set Italic ESC 5 Cancel Italic ESC 6 Enable printable characters ESC 7 Enable upper control characters
Tally Dascom 1125 85 ESC : Copy ROM to RAM ESC ˘ Unidirectional mode(1 line) ESC > Set MSB to 1 ESC = Set MSB to 0 ESC # Cancel MSB control ESC ˛n m Reassign graphics mode ESC @ Initialize printer ESC ˸n1 n2 Set relative horizontal print position ESC A n Set n/60Ǝline spacing ESC B…NUL Set/cancel vertical tabs ESC C n Set page length in lines ESC D…NUL Set/cancel horizontal tabs ESC E Select Bold ESC F Cancel Bold ESC G Select double-strike mode ESC H Cancel double-strike mode ESC J n Perform tactic n/180Ǝline feed ESC K n1 n2 … Select 8 pins single-density graphics ESC L n1 n2 … Select 8 pins double–density graphics ESC M Select ELITE˄12CPI˅ ESC N n Set bottom margin ESC O Cancel bottom margin ESC P Select PICA˄10CPI˅ ESC Q n Set right margin ESC R n International character set ESC S n Select superscript/subscript ESC T Cancel superscript/subscript ESC U n Select unidirectional/bidirectional printing mode ESC ( V NUL n m Select absolute vertical print position ESC W n Turn Double-wide mode on/off ESC X n1 n2 Select font by pitch and point ESC Y n1 n2 … Select 8 pins, high speed ,double –density graphics ESC Z n1 n2 … Select 8 pins, high speed fourfold –density graphics ESC a n Select justification ESC b n Select vertical orientation channel ESC c n m Set horizontal intercharacter space ESC g Select 15CPI ESC j n Perform reverse n/180Ǝline feed ESC k n Select typeface ESC p n Turn proportional mode on/off ESC q n Select character style ESC r n Select printing colour ESC t n Select character table ESC (t nL nH d1 d2 d3 Assign character table ESC ( v NUL n m Set relative vertical print position ESC w n Turn double-high mode on/off ESC x n Select print quality ESC( B n1 n2 k m s v1 v2 c Barcode print
Tally Dascom 1125 86 IBM Emulation Command List Command Sequence Function BEL Beeper BS Backspace HT Tab horizontally LF Line feed VT Tab vertically FF Form feed CR Enter SO Select double-wide mode SI Select condensed mode DC1 Online DC2 Select 10CPI DC3 Offline DC4 Cancel double-wide mode(one line) CAN Cancel buffer ESC BEL Beeper ESC BS Backspace ESC HT Tab horizontally ESC CR Enter ESC LF Line feed ESC SO Select double-wide mode ESC SI Select condensed mode ESC DC1 Online ESC DC2 Select 10CPI ESC DC3 Offline ESC DC4 Cancel double-wide mode(one line) ESC CAN Cancel buffer ESC FF Form feed ESC EM n Automatically Feed Paper mode ESC : Set 12CPI ESC VT Tab vertically ESC 0 Select 1/8Ǝline spacing ESC 1 Select 7/72Ǝline spacing ESC 2 Select 1/6Ǝline spacing or activate ESC A n command ESC 3 n Select n/216Ǝor 1/180Ǝline spacing ESC 4 Set top margin ESC 5 n Automatic Line Feed ESC 6 Select character set 2 ESC 7 Select character set 1 ESC = NA ESC \ Print continuously from all character chart ESC ^ Print single character from all character chart ESC A n Select n/72Ǝor n/60Ǝline spacing ESC B n Select Tab vertically ESC C n Set page length in lines
Tally Dascom 1125 87 ESC C NUL n Set page length in inches ESC D Select Tab horizontally ESC E Select bold ESC F Cancel bold ESC G Select double-strike mode ESC H Cancel double-strike mode ESC I n Select printing mode ESC J n Perform n/180Ǝor n/216Ǝsingle line feed ESC K n1 n2 V1 V2 …Vn Normal density graphics ESC L n1 n2 V1 V2 …Vn Dual-Density Bit Image Graphics (Half Speed) ESC N n Select bottom margin ESC O Cancel bottom margin ESC P n Set proportional intercharacter ESC Q n Offline ESC R Clear tab ESC S n Select superscript/subscript ESC T Cancel superscript/subscript ESC U n Select bidirectional printing on/off ESC W n Select double-wide printing mode(continuous) ESC X n m Set left and right margin ESC Y n1 n2 V1 V2 …Vn Select double -density graphics ESC Z n1 n2 V1 V2 …Vn Select fourfold -density graphics ESC [- n1 n2 m1 m2 Select line ESC [@ n1 n2 m1 m2 m3 m4 Select printing mode ESC [I n1 n2 Hf Ls Hs Lf Sm NUL Hc Lc Select font and pitch ESC [ K n1 n2 init id para1 para2 …paran Set initialization condition ESC [ T n1 n2 n3 n4 Hc Lc Set code page ESC [\ Set vertical unit ESC [d Select printing quality ESC [f n1 n2 k m s v1 v2c Set barcode parameters ESC [g n1 n2 m Select high-density graphics printing ESC [p n1 n2 Set barcode data ESC ] Feed paper in reverse direction ESC_ n Print upper-line ESC- n Print underline ESC d n m Move the current printing position ESC j Stop printing ESC r n Select printing colour ESC * m Select graphic mode If you need more details regarding the emulation commands, please contact us.
Tally Dascom 1125 88 FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: a. This device may not cause harmful interference. b. This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: xRe-orientate or relocate the receiving antenna. xIncrease the separation between the equipment and receiver. xConnect the equipment into an outlet on a circuit different from that to which the receiver is connected. xConsult the dealer or an experienced radio/TV technician for help.
DASCOM REPRESENTATIVES GERMANY DASCOM Europe GmbH Heuweg 3 D-89079 Ulm Deutschland Tel.: +49 (0) 731 2075 0 Fax: +49 (0) 731 2075 100 www.dascom.com UNITED KINGDOM DASCOM GB Ltd ViewPoint, Basing View, Basingstoke, Hampshire RG21 4RG, England Phone: +44 (0) 1256 481481 Fax: +44 (0) 1256 481400 www.dascom.com RUSSIA and CIS DASCOM Europe GmbH Representation Moscow Leninsky Prospekt 95a, Office 322 119313 Moscow, Russian Federation Phone: +7 (495) 984 70 65 Fax: +7 (495) 984 56 42 www.dascom.com SINGAPORE (ASIA PACIFIC) DASCOM AP Pte Ltd 63 Hillview Avenue #08-22, Lam Soon Industrial Building Singapore 669569 Phone: +65 6760 8833 Fax: +65 6760 1066 www.dascom.com.sg AMERICAS DASCOM Americas Corporation 421 W. Main Street, Waynesboro, VA 22980, USA Phone:+1 (877) 434 13 77 www.dascom.com FRANCE DASCOM Europe GmbH 117 Avenue Victor Hugo 92100 Boulogne-Billancourt France Phone: +33 (1) 73 02 51 98 www.dascom.com CEE DASCOM Europe GmbH Europaring F15 301 2345 Brunn a. G. Austria Phone: +43 (1) 236 01 70 10 www.dascom.com “All rights reserved. Translations, reprinting or copying by any means of this manual complete or in part or in any different form requires our explicit approval. We reserve the right to make changes to this manual without notice. All care has been taken to ensure accuracy of information contained in this manual. However, we cannot accept responsibility for any errors or damages resulting from errors or inaccuracies of information herein.” © 2011 DASCOM Part No: 21.511.800.0042

Navigation menu