Jogtek TM-007-MINI NFC Reader User Manual User s manualx

Jogtek Corp. NFC Reader User s manualx

user manual

1 TM-007-Mini User’ manual
TM-007-Mini User’s manual Jogtek Corp. 2 Table of Contents Chapter 1 – Product overview……………………………………………3 Chapter 2 – Mechanical Characteristics………………………………...4 Chapter 3 – Software application………………………………………...5 Chapter 4 –Safety Statements…………………………………………….6
TM-007-Mini User’s manual Jogtek Corp. 3 1. Product overview 1. General Description The TM-007-Mini is an OEM NFC module for integration into Tablet, Notebook, Smartphone, label printers, handheld devices and in general any fixed or mobile short and medium range device requiring NFC technology. TM-007-Mini supports Near Field Communication Standards NFCIP-1 (ISO/IEC 18092) and NFCIP-2 (ISO/IEC21481) which defines the selection of any of the four possible communication modes (NFC peer-to-peer, card emulation, proximity reader/writer, ISO14443A/B or FeliCa and Vicinity reader/writer – ISO15693). TM-007-Mini , Its simplified UART interface, low power consumption and superior performance, make it easy to integrate any device with NFC technology.
TM-007-Mini User’s manual Jogtek Corp. 4 2. Mechanical Characteristics 2.1 Dimensions: 10 x 20 x 2.35 mm
TM-007-Mini User’s manual Jogtek Corp. 5 3. Software application 1.Open Program: 2.Press “open” 3. If the port communication is successful, the window below will display “Version : TM-007 V1.0”.
TM-007-Mini User’s manual Jogtek Corp. 6 4. Safety Statements Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
TM-007-Mini User’s manual Jogtek Corp. 7 IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g. Verification , Doc) of the host device to be addressed by the integrator/manufacturer. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following "FCCID: VZPTM-007-MINI ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu