Johnson Controls Ifc 640 Users Manual Intelligent Addressable Fire Alarm System Catalog Page

IFC-640 JCI_6856

IFC-640 to the manual 53b80411-3061-4df1-b153-aaca0519d316

: Johnson-Controls Johnson-Controls-Ifc-640-Users-Manual-567035 johnson-controls-ifc-640-users-manual-567035 johnson-controls pdf

Open the PDF directly: View PDF .
Page Count: 9

JCI-6856:A • 12/01/06 — Page 1 of 9

IFC-640

Intelligent Addressable

Fire Alarm System

JCI-6856:A

IFC-640 shown in CAB-4 with

JNCA 640-character display

General

As a stand-alone small-to-large system, or as a large network,

the IFC-640 meets virtually every application requirement.

Designed with modularity and for ease of system planning, the

IFC-640 can be configured with just a few devices for small

building applications, or for a large campus or high-rise applica-

tion. Simply add additional peripheral equipment to suit the

application.

Features

• One, expandable to two, isolated intelligent Signaling Line

Circuit (SLC) Style 4, 6 or 7.

• Up to 159 detectors (any mix of ion, photo, thermal, or multi-

sensor) and 159 modules (N.O. manual stations, two-wire

smoke, notification, or relay) per SLC. 318 devices per loop/

636 per FACP or network node.

• Standard 80-character display, 640-character large display,

or display-less (a node on a network).

• Network option – 103 nodes supported (IFC-640, JNCA Net-

work Annunciator, or IFW Network Control Station).

• 6.0 amp switch mode power supply with four Class A/B built-

in Notification Appliance Circuits (NAC). Selectable System

Sensor strobe synchronization.

• Built-in Alarm, Trouble, and Supervisory relays.

• Up to 64 output circuits per FACP or network node; circuits

configurable online.

• Autoprogramming and Walk Test reports.

• Optional universal 636-point DACT.

• 80-character remote annunciators (up to 32).

• EIA-485 annunciators, including custom graphics.

• Printer interface (80-column and 40-column printers).

• History file with 800-event capacity in nonvolatile memory,

plus separate 200-event alarm-only file.

• Alarm Verification selection per point, with tally.

• Autoprogramming and Walk Test reports.

• Positive Alarm Sequence (PAS) Presignal.

• Silence inhibit and Auto Silence timer options.

• March time / temporal / California two-stage coding / strobe

synchronization.

• Field-programmable on panel or on PC

• Full QWERTY keypad.

• Charger for up to 90 hours of standby power.

• Non-alarm points for lower priority functions.

• Remote ACK/Signal Silence/System Reset/Drill via monitor

modules.

• Automatic time control functions, with holiday exceptions.

• Surface Mount Technology (SMT) electronics.

• Extensive, built-in transient protection.

• Powerful Boolean logic equations.

JNCA 640-CHARACTER DISPLAY FEATURES:

• Backlit, 640-character display.

• Supports SCS Series smoke control system in both HVAC or

FSCS modes .

• Printer and CRT EIA-232 ports.

• EIA-485 annunciator and terminal mode ports.

• Alarm, Trouble, Supervisory, and Security relays.

FLASHSCAN® INTELLIGENT FEATURES:

• Poll 318 devices in less than two seconds.

• Activate up to 159 outputs in less than five seconds.

• Multicolor LEDs blink device address during Walk Test.

• Fully digital, high-precision protocol (U.S. Patent 5,539,389).

• Manual sensitivity adjustment — nine levels.

• Pre-alarm AWACS — nine levels.

• Day/Night automatic sensitivity adjustment.

• Sensitivity windows:

–Ion – 0.5 to 2.5%/foot obscuration.

–Photo – 0.5 to 2.35%/foot obscuration.

– Laser (VIEW®) – 0.02 to 2.0%/foot obscuration.

–Acclimate – 0.5 to 4.0%/foot obscuration.

–HARSH™ – 0.5 to 2.35%/foot obscuration.

• Drift compensation (U.S. Patent 5,764,142).

• Degraded mode — in the unlikely event that the JCPU-640

microprocessor fails, FlashScan® detectors revert to

degraded operation and can activate the JCPU-640 NAC cir-

cuits and alarm relay. Each of the four built-in panel circuits

includes a Disable/Enable switch for this feature.

Page 2 of 9 — JCI-6856:A • 12/01/06

• Multi-detector algorithm involves nearby detectors in alarm

decision (U.S. Patent 5,627,515).

• Automatic detector sensitivity testing.

• Maintenance alert (two levels).

• Self-optimizing pre-alarm.

VIEW® (VERY INTELLIGENT EARLY WARNING)

SMOKE DETECTION TECHNOLOGY:

• Revolutionary spot laser design.

• Advanced AWACS algorithms differentiate between smoke

and non-smoke signals (U.S. Patent 5,831,524).

• Addressable operation pinpoints the fire location.

• No moving parts to fail or filters to change.

• Early warning performance comparable to the best aspiration

systems at a fraction of the lifetime cost.

ACCLIMATE

LOW-PROFILE INTELLIGENT MULTI-SENSOR:

• Detector automatically adjusts sensitivity levels without oper-

ator intervention or programming. Sensitivity increases with

heat.

• Microprocessor-based technology; combination photo and

thermal technology.

• FlashScan® or classic mode compatible with IFC-640.

• Low-temperature warning signal at 40°F ± 5°F (4.44°C ±

2.77°C).

RFX WIRELESS INTERFACE SYSTEM:

• Allows protection in areas where the use of wire is uneco-

nomical or unpractical.

• Allows communication with wireless smoke detectors and

wireless monitor modules; each RFX unit and detector is

assigned an address.

• Requires 24 VDC from SLC or system auxiliary power.

HARSH™ HOSTILE-AREA SMOKE HEAD:

• Provides early warning of smoke detection in environment

where traditional smoke detectors are not practical.

• The detector's filters remove particulates down to 30 microns

in size.

• Intake fan draws air into photo chamber, while airborne parti-

cles and water mist are removed.

• Requires auxiliary 24 VDC from system or remote power

supply.

RELEASING FEATURES:

• Ten independent hazards.

• Sophisticated cross-zone (three options).

• Delay timer and Discharge timers (adjustable).

• Abort (four options).

• Low-pressure CO2 listed.

VOICE AND TELEPHONE FEATURES:

• Solid state message generation.

• Hard-wired voice control module options.

• Firefighter telephone option.

• 30- to 120-watt high-efficiency amplifiers (AA Series).

• Backup tone generator and amplifier option.

• Multichannel voice transponder (XPIQ).

HIGH-EFFICIENCY OFFLINE SWITCHING

3.0 AMP POWER SUPPLY (6.0 A IN ALARM):

• 120 or 220/240 VAC.

• Displays battery current/voltage on panel (with display).

Sample

System

Options

JCI-6856:A • 12/01/06 — Page 3 of 9

FlashScan®

Exclusive World-Leading Detector Pro-

tocol

At the heart of the IFC-640 is a set of detection devices and

device protocol — FlashScan® (U.S. Patent 5,539,389). Flash-

Scan® is an all-digital protocol that gives superior precision and

high noise immunity.

In addition to providing quick identification of an active input

device, this protocol can also activate many output devices in a

fraction of the time required by competitive protocols. This high

speed also allows the IFC-640 to have the largest device per

loop capacity in the industry — 318 points — yet every input and

output device is sampled in less than two seconds. The micro-

processor-based FlashScan® detectors have bicolor LEDs that

can be coded to provide diagnostic information, such as device

address during Walk Test.

AWACS™ Advanced Warning Address-

able Combustion Sensing

AWACS is a set of software algorithms that provide the IFC-640

with industry-leading smoke detection capability. These complex

algorithms require many calculations on each reading of each

detector, and are made possible by the very-high-speed micro-

computer used by the IFC-640.

Drift Compensation and Smoothing: Drift compensation

allows the detector to retain its original ability to detect actual

smoke, and resist false alarms, even as dirt accumulates. It

reduces maintenance requirements by allowing the system to

automatically perform the periodic sensitivity measurements

required by NFPA 72. Smoothing filters are also provided by

software to remove transient noise signals, such as those

caused by electrical interference.

Maintenance Warnings: When the drift compensation per-

formed for a detector reaches a certain level, the performance of

the detector may be compromised, and special warnings are

given. There are three warning levels: (1) Low Chamber value,

usually indicative of a hardware problem in the detector; (2)

Maintenance Alert, indicative of dust accumulation that is near

but below the allowed limit; (3) Maintenance Urgent, indicative of

dust accumulation above the allowed limit.

Sensitivity Adjust: Nine sensitivity levels are provided for

alarm detection. These levels can be set manually, or can

change automatically between day and night. Nine levels of pre-

alarm sensitivity can also be selected, based on predetermined

levels of alarm. Pre-alarm operation can be latching or self-

restoring, and can be used to activate special control functions.

Self-Optimizing Pre-Alarm: Each detector may be set for

“Self-Optimizing” pre-alarm. In this special mode, the detector

“learns” its normal environment, measuring the peak analog

readings over a long period of time, and setting the pre-alarm

level just above these normal peaks.

Cooperating Multi-Detector Sensing: A patented feature of

AWACS is the ability of a smoke sensor to consider readings

from nearby sensors in making alarm or pre-alarm decisions.

Without statistical sacrifice in the ability to resist false alarms, it

allows a sensor to increase its sensitivity to actual smoke by a

factor of almost two to one.

Field Programming Options

Autoprogram is a timesaving feature of the IFC-640. It is a spe-

cial software routine that allows the IFC-640 to “learn” what

devices are physically connected and automatically load them in

the program with default values for all parameters. Requiring

less than one minute to run, this routine allows the user to have

almost immediate fire protection in a new installation, even if

only a portion of the detectors are installed.

Keypad Program Edit (with KDM-2) The IFC-640 has the

exclusive feature of program creation and editing capability from

the front panel keypad, while continuing to provide fire pro-

tection. The architecture of the IFC-640 software is such that

each point entry carries its own program, including control-by-

event links to other points. This allows the program to be

entered with independent per-point segments, while the IFC-

640 simultaneously monitors other (already installed) points for

alarm conditions.

VeriFire® Tools is an offline programming and test utility that

can greatly reduce installation programming time, and increase

confidence in the site-specific software. It is Windows® based

and provides technologically advanced capabilities to aid the

installer. The installer may create the entire program for the IFC-

640 in the comfort of the office, test it, store a backup file, then

bring it to the site and download from a laptop into the panel.

ENTER PROG OR STAT PASSWORD, THEN ENTER

<ESCAPE TO ABORT> *****

Above: Keypad program editing.

Below: Autoprogram function.

VeriFire ToolsSystem Programming screen

0=CLR 1= AUTO 2=POINT 3=PASSWORD 4=MESSAGE

AUTOPROGRAM PLEASE WAIT

L1:80 DETS, 15 MODS L2:93 DETS, 35 MODS

PANEL OUTPUTS:24 BELLS: 04

Page 4 of 9 — JCI-6856:A • 12/01/06

TOP, LEFT to RIGHT: J8 Zone Code Input; TB7 DC Power (24 VDC power-limited, both resettable and non-resettable available); TB8

Alarm Relay; TB9 Trouble Relay; TB10 Supervisory Relay; TB11 Security Relay; SW1, SW5 Relay Switches; JP13 General Board

Earth Fault Jumper; TB12 EIA-485 Terminal Mode (supervised); TB13 EIA-485 ACS Mode (supervised); TB14 EIA-232 Printer; TB15

EIA-232 PC Terminal; J1 NUP (network/service connection: power-limited, supervised); TB16 SLC #1 Connections (detectors,

modules; supervised); D55 Main SLC Ground Fault LED; JP7 Charger Disable Jumper; JP12 200MA Jumper; JP6 Earth Fault Jumper

(SLC #1).

JCPU-640 shown with

KDM-2 Display

LEFT SIDE, TOP to BOTTOM: TB6 NAC #1, TB5 NAC #2, TB4 NAC #3, TB3 NAC #4 (all NAC circuits power-limited and supervised,

and each NAC TB has an NAC LED to the right of it); J7 Accessory Power; Disable/Enable Switches for Degraded Mode; TB2 AC

Power Connection; TB1 Battery Connection (overcurrent protected). BOTTOM, LEFT to RIGHT: D54 AC On LED; System Status

Indicator LEDs for “No-Keyboard Operation”; System Switches SW2 (Acknowledge), SW3 (Silence), SW4 (Reset) for “No-Keyboard

Operation”; J4 KDM-2 Connector; J5, J6 Panel Circuits (Panel Output Modules, supervised); D72 General Board Ground Fault LED;

J10 Security Tamper Switch; J11 Auxiliary Trouble Input; D82 AC Power LED; J3 LEM-320 Connector (SLC Loop #2).

IFW

IFC-640

IFC-640

IFW

JNCA

Network Diagram

JCI-6856:A • 12/01/06 — Page 5 of 9

Placement of Equipment

in Chassis and Cabinet

The following guidelines outline the IFC-640’s flexible system

design.

Rows: The first row of equipment in the cabinet mounts in

chassis CHS-M2. Mount the second, third, or fourth rows of

equipment in chassis CHS-4MB (see IFC-640 Installation Man-

ual regarding panel output modules) or CHS-4L (for voice com-

ponents, see Voice Alarm System Manual).

Wiring: When designing the cabinet layout, consider separa-

tion of power-limited and non-power-limited wiring as discussed

in the IFC-640 Installation Manual.

Positions: A chassis offers four basic side-by-side positions for

components; the number of modules that can be mounted in

each position depends on the chassis model and the size of the

individual module. There are a variety of standoffs and hardware

items available for different combinations and configurations of

components.

It is critical that all mounting holes of the IFC-640 are secured

with a screw or standoff to ensure continuity of Earth Ground.

Layers: The CHS-M2 accepts four layers of equipment, includ-

ing the control panel. The JCPU-640 fills three positions (left to

right) in the first-installed layer (the back of the chassis); its inte-

gral power supply occupies (the left) two positions in the next

two layers; the optional display occupies (the left) two positions

at the front, flush with the door. Panel output modules can be

mounted in several layers with standoffs or an L-bracket as

required. Some equipment, such as the JNCA, may be door-

mounted directly in front of the control panel. The JNCA mounts

onto the DP-DISP or ADP-4B. The JNCA can be used as a pri-

mary display for the IFC-640 by directly connecting their network

ports (required in Canadian stand-alone applications).

Expansion: Installing an LEM-320 Loop Expander Module

adds a second SLC loop to the control panel. The LEM-320 is

mounted onto the JCPU-640, occupying the middle-right, sec-

ond (back) slot on the chassis. If networking two or more control

panels, each unit requires a NCM-W (wire) or NCM-F (fiber)

Network Control Module. The NCM-W/-F can be installed in any

panel output module position (see manual); the default position

is at the back of the chassis next to the control panel. Option

boards can be mounted in front of the LEM-320 or NCM mod-

ules; for ease of access, complete installation of those devices

before mounting another layer.

KDM-2 Controls and Indicators

Program Keypad: QWERTY type (keyboard layout).

8 LED indicators: Power; Fire Alarm; Pre-Alarm; Security;

Supervisory; System Trouble; Signals Silenced; Points Dis-

abled.

Membrane Switch Controls: Acknowledge/Scroll Display;

Signal Silence; Drill; System Reset; Lamp Test.

LCD Display: 80 characters (2 x 40) with long-life LED back-

light.

Configuration Guidelines

Stand-alone and network systems require a main display. On

single-CPU systems (one JCPU-640/-640E), display options are

the KDM-2 or the JNCA. On network systems (two or more

JCPU-640/-640Es), at least one JNCA or IFW annunciation

device is required. Other options listed as follows:

KDM-2: 80-character backlit LCD display with QWERTY pro-

gramming and control keypad. Order two BMP-1 blank modules

and DP-DISP mounting plate separately. Requires top row of a

cabinet. Required for each stand-alone 80-character display

system. The KDM-2 may mount in network nodes to display

“local” node information as long as at least one JNCA or IFW

network display is on the system to display network information.

JNCA: Network Control Annunciator, 640 characters. On single

CPU-640/-640E systems, the JNCA is the Primary Display for

the panel and connects directly to the CPU-640/-640E. On net-

work systems (two or more CPU-640/-640Es), one network dis-

play (either JNCA or IFW) is required for every system. On

network systems, the JNCA connects (and requires) an NCM

network communications module. Mounts in a row of FACP

node or in two annunciator positions. Mounting options include

the DP-DISP, ADP-4B, or in an annunciator box, such as the

JABS-2D. In CAB-4 top-row applications, a DP-DISP and two

BMP-1 blank modules are required for mounting. See JNCA

technical bulletin.

JCPU-640: Central processing unit with integral 3.0 amp (6.0 A

in alarm) power supply for an IFC-640 system. Includes CPU;

one Signaling Line Circuit expandable to two; installation, pro-

gramming and operating manuals. Order one per system or as

necessary (up to 103 network nodes) on a network system.

JCPU-640E: Same as JCPU-640 but requires 220 VAC, 1.5

amp, (3.0 A in alarm).

JCPU-640

KDM-2 shown with dress

plate, or JNCA at front, flush

with door.

Page 6 of 9 — JCI-6856:A • 12/01/06

CHS-M2: Mounting chassis for JCPU-640. One required for

each CPU-640/-640E.

DP-DISP: Dress panel for top row in cabinet with CPU-640/-

640E installed.

BMP-1: Blank module for unused module positions.

System Modules

The IFC-640 includes the ability to communicate with up to eight

conventional modules each with up to eight circuits. Any mix of

notification, relay, speaker, or telephone may be used. Choose

any combination of up to eight output modules: ICM/ICE, CRM/

CRE, DCM-4 or VCM/VCE. Panel modules mount on either: the

two far-right positions of the DP-DISP (next to the primary dis-

play); or on any of the four positions on the CHS-4N chassis

(CHS-4MN kit required).

NOTES: 1) These modules/expanders are NOT to be used for

releasing applications. 2) For additional information on these panel

output modules and expanders, see technical bulletin.

CHS-4MB: Expansion Chassis. Mounts up to four modules.

Includes CHS-4N, MP-1B (Module Dress Panel), and Expander

Ribbon Cable.

ICM-4RK: Notification Appliance Circuit Module, provides four

Style Y (Class B) or Style Z (Class A) alarm Notification Appli-

ance Circuits. Maximum signaling current is 3.0 amps per circuit

or 6.0 amps per module, subject to power supply limitations

(includes auxiliary power harness, ELRs and slide-in labels).

Includes ON/OFF controls and ON/OFF LEDs.

ICE-4: Notification Appliance Circuit Expander, expands ICM-4

to provide a total of eight Style Y or Style Z alarm Notification

Appliance Circuits. Circuit ratings are same as ICM-4.

NOTE: Maximum of one per ICM-4RK. May also be used to add

four Notification Appliance Circuits to VCM-4.

CRM-4RK: Control Relay Module, four Form-C relay contacts,

rated at 5.0 A, 120 VAC or 28 VDC (resistive) per circuit.

Includes manual ON/OFF controls and LEDs.

CRE-4: Control Relay Expander, expands CRM-4 to provide a

total of eight Form-C relay contacts. Note: maximum of one per

CRM-4RK. May also be connected to add four relays to ICM-4,

TCM-2, TCM-4, or VCM-4.

VCM-4RK: Voice Control Module provides four Style Y (25 and

70 Vrms) and Style Z (25 Vrms only) speaker circuits, eight

manual select switches and indicators, slide-in labels, and plug-

in terminal blocks. Move jumper to convert to telephone circuits

with remote ring signal and local call-in flash. May be expanded

to eight circuits with VCE-4, ICE-4, or CRE-4.

VCE-4: Voice Control Expander adds four circuits to VCM-4.

Note: VCM-4/ VCE-4 combination must be eight speaker or

eight phone circuits.

DCM-4RK: Dual Channel Module pro-vides four Class B (Style

Y, 25 & 70 Vrms) or Class A (Style Z, 25 Vrms only) speaker cir-

cuits plus four channel A/B select relays. Not expandable.

OTHER OPTION MODULES

ARM-4: Auxiliary Relay Module, four Form-C relays controlled

by a relay module (CRM-4 or CRE-4). N.O. contacts rated 20

amps; N.C. contacts rated 10 amps at 125 VAC and 30 VDC.

NOTE: Maximum of one for each CRM-4 or CRE-4.

JVCC-1B: Voice Control Center. Provides a variety of user-

selectable tones on a single channel. Up to two different tones

or messages may be selected on a single channel. Also pro-

vides optional digital voice message capability and on-site pro-

grammable voice messages. Includes Audio Message

Generator (AMG-1) microphone, cables, dress panels, and

instructions.

JVTCC-1B: Voice/Telephone Control Center. Provides all that

the JVCC-1 provides plus two-way Fire Fighters Telephone

(FFT-7) capability.

JTCC-1B: Telephone Control Center. Provides a stand-alone

two-way Fire Fighters telephone (FFT-7S).

Includes cables, dress panel and instructions.

RM-1/RM-1SA: Remote microphone assemblies, mount on

ADP-4 (RM-1) dress panel or CAB-RM/-RMR (RM-1SA) stand-

alone cabinets. See DN-6728.

AMG-E: Audio Message Generator (without microphone).

Order in addition to JVCC-1 or JVTCC-1 if two-channel system

is required.

FFT-7/FFT-7S: Fire Fighters Telephone control with master

handset.

FTM-1: Firephone Control Module connects a remote firefighter

telephone to a centralized telephone console. Reports status to

panel. Wiring to jacks and handsets is supervised.

AA-30: Audio Amplifier, 30 watts. Switch-mode power. Includes

amplifier and audio input supervision, backup input, and auto-

matic switchover, power supply, cables. See AA Series technical

bulletin.

AA-120/AA-100: Audio Amplifier provides up to 120 watts of 25

Vrms audio power for the IFC-640. The amplifier contains an

integral chassis for mounting to a CAB-B4, -C4, or -D4 backbox

(consumes one row). Switch-mode power. Includes audio input

and amplified output supervision, backup input, and automatic

switchover to backup tone. Order the AA-100 for 70.7 Vrms sys-

tems and 100 watts of power. See AA Series technical bulletin.

VROM-(n): Factory-programmed message for installation in

AMG-1. Provides up to 24 seconds of evacuation message on

nonvolatile memory chip. Choose one of many standard mes-

sages available. Up to two of these messages may be installed

in one AMG. Includes VROM, instructions for installation and

operation, and written text of message. See VROM technical

bulletin.

VRAM-1: Field-programmed memory to be installed in AMG-1.

Provides up to 24 seconds of field-programmable evacuation

message on nonvolatile memory chip. Message is programmed

from microphone or cassette tape. Up to two of these nonvolatile

memory chips may be installed in one AMG. Includes VRAM

and instructions for installation and operation.

APS-6R: Auxiliary Power Supply (expander). Provides up to 6.0

amperes of regulated power for compatible Notification appli-

ance circuits. Includes battery input and transfer relay, and over-

current protection. Mounts on one of four positions on a CHS-4L

or CHS-4 chassis. See APS-6R technical bulletin.

ACPS-2406: 6.0 amp addressable charger power supply. See

ACPS-2406 technical bulletin.

FCPS-24: The FCPS-24 is a remote six-amp (four-amp contin-

uous) repeater/power supply. See FCPS-24 technical bulletin.

FCPS-24S6/-24S8: Remote six-amp and eight-amp power sup-

plies with battery charger. See FCPS-24S6/-24S8 technical bul-

letin.

UZC-256: Programmable Universal Zone Coder provides posi-

tive non-interfering successive zone coding. Microprocessor-

controlled, field-programmable from IBM®-compatible PCs

(requires optional programming kit). See UZC-256 technical bul-

letin.

LCD-80/LCD-80TM/FDU-80: 80-character, backlit LCD dis-

play. Mounts up to 6,000 ft. (1828.8 m) from panel. Up to 32 per

IFC-640. See LCD-80/-80TM and FDU-80 technical bulletins.

ACS: Annunciator Control Modules ACM-16AT, AEM-16AT,

ACM-32A, and AEM-32A. See ACS technical bulletin and ACM/

AEM-24AT and ACM/AEM-48A technical bulletin.

AFM: Annunciator Fixed Modules AFM-16A, AFM-16AT, and

AFM-32A. See AFM technical bulletin.

JCI-6856:A • 12/01/06 — Page 7 of 9

LDM: Lamp Driver Modules LDM-32, LDM-E32, and LDM-R32.

See LDM technical bulletin.

ACM-8R: Remote Relay Module with eight Form-C contacts.

Can be located up to 6,000 ft. (1828.8 m) from panel on four

wires. See ACM-8R technical bulletin.

SCS: Smoke control station; eight (expandable to 16) circuits.

See SCS technical bulletin.

RPT-485: Repeats EIA-485 over twisted pair or converts to

fiber-optic medium. See RPT technical bulletin.

XP5: The XP5-M and XP5-C provide FlashScan® transponder

points. See XP5 technical bulletin.

XP: The XP Series Transponder provides conventional monitor

and control points (CLIP mode only). See XP Series technical

bulletin.

XPIQ: The XPIQ quad intelligent voice transponder for distrib-

uted multichannel voice evacuation systems, an integrated

audio amplification and distribution subsystem controlled by

FACP. Capable of playing up to four simultaneous messages.

Accepts up to four 25-watt amplifiers. See XPIQ technical bulle-

tin.

CHS-4: Chassis for mounting up to four APS-6Rs.

CHS-4L: Low-profile four-position Chassis. Mounts two AA-30

amplifiers or one AMG-E and one AA-30.

DP-1B: Blank Dress panel. Provides dead-front panel for

unused tiers or to cover AA-30, AA-120, or one AMG-E and one

AA-30.

CAB-4 Series: The CAB-4 Series cabinets are fabricated from

16-gauge steel. The cabinet assembly consists of two basic

parts: a Backbox (SBB-_4), and a Locking Door (DR-_4) that

may hinge right or left. Cabinets are available in four sizes, “A”

through “D”, with one to four tiers. A trim ring option is available

for semi-flush mounting. See CAB-4 Series technical bulletin.

COMPATIBLE DEVICES, EIA-232 PORTS

JPRN-5: 80-column printer.

JPRN-6: 80-column printer.

VS4095/S2: Printer, 40-column, 24 V. Mounted in external

backbox. Order from Keltron, Inc.

CRT-2: Video display terminal.

COMPATIBLE DEVICES, EIA-485 PORTS

ACS Series: Remote serial annunciator/control systems.

FDU-80: Remote LCD display, 80 characters, with LEDs.

LCD-80: Remote LCD display, 80 characters.

LCD-80TM: Remote LCD display, 80 characters, terminal

mode.

LDM Series: Remote custom graphic driver modules.

ACM-8R: Remote relay module. 8 Form-C relays.

RPT-485 Series: Repeater, isolator and/or fiber-optic modem.

UDACT: Universal Digital Alarm Communicator Transmitter,

636 channel.

UZC-256: Zone Coder. Up to 256 programmable codes.

COMPATIBLE INTELLIGENT DEVICES

BEAMHK: Heating kit for transmitter/receiver unit of FSB-

200(S) below.

BEAMHRK: Heating kit for use with the reflector of FSB-200(S)

below.

BEAMLRK: Long-range accessory kit, FSB-200(S) below.

BEAMMRK: Multi-mount kit, FSB-200(S) below.

BEAMSMK: Surface-mount kit, FSB-200(S) below.

FSB-200: Intelligent beam smoke detector.

FSB-200S: Intelligent beam smoke detector with integral sensi-

tivity test.

1951J: Low-profile FlashScan® ionization detector, will replace

1351J.

1351J: Low-profile FlashScan® ionization detector.

2951J: Low-profile FlashScan® photoelectric detector, will

replace 2351J.

2351J: Low-profile FlashScan® photoelectric detector.

2951TJ: Low-profile FlashScan® photoelectric detector with

135°F (57°C) thermal, will replace 2351TJ.

2351TJ: Low-profile FlashScan® photoelectric detector with

135°F (57°C) thermal.

5951J: FlashScan® thermal detector 135°F (57°C), will replace

5351J.

5351J: FlashScan® thermal detector 135°F (57°C).

5951RJ: FlashScan® thermal detector 135°F (57°C) with rate-

of-rise, will replace 5351RJ.

5351RJ: FlashScan® thermal detector 135°F (57°C) with rate-

of-rise.

5951HJ: FlashScan® 190°F (88°C) high-temperature thermal

detector.

DH300PL: Low-flow FlashScan® photo duct detector with

housing.

DH300RPL: Low-flow FlashScan® photo duct detector with

relay and housing.

2951TMJ: FlashScan® Acclimate low-profile multi-sensor

detector.

FTX-P2J: FlashScan® HARSH™ Hostile Area Smoke Head.

7351J: FlashScan® VIEW® laser photo detector, will replace

7251J.

7251J: Low-profile VIEW® laser photo detector.

B224RB: Low-profile relay base.

B224BI: Isolator base for low-profile detectors.

B210LPJ: Low-profile base. Standard U.S. style.

B501J: European-style, 4" (10.16 cm) base.

B501BH: Sounder base, includes B501J base above. Constant

tone.

B501BHT: Sounder base, includes B501J base above. Tempo-

ral three tone.

M300MJ: FlashScan® monitor module.

M300DJ: FlashScan® dual monitor module.

M302MJ: FlashScan® two-wire detector monitor module.

M301MJ: FlashScan® miniature monitor module.

M300CJ: FlashScan® NAC control module.

M300RJ: FlashScan® relay module.

M300SMJ: FlashScan® pull station monitor module.

JBG-12LX: Manual fire alarm station, addressable.

M500XJ: Isolator module.

XP6-C: FlashScan® six-circuit supervised control module.

XP6-MA: FlashScan® six-zone interface module; connects

intelligent alarm system to two-wire conventional detection

zone.

XP6-R: FlashScan® six-relay (Form-C) control module.

XP10-M: FlashScan® ten-input monitor module.

XPIQ: Intelligent quad transponder.

OTHER OPTIONS

DPI-232: Direct Panel Interface, specialized modem for extend-

ing serial data links to remotely located FACPs and/or peripher-

als.

LEM-320: Loop Expander Module. Expands each 640 to two

Signaling Line Circuits.

Page 8 of 9 — JCI-6856:A • 12/01/06

TM-4: Transmitter Module. Includes three reverse-polarity cir-

cuits and one municipal box circuit. Mounts in panel module

position (single-address-style) or in CHS-M2 position.

NCM-W: Network Communications Module, Wire. Order one

NCM per network node (JCPU-640 or JNCA).

NCM-F: Network Communications Module, Fiber. Order one

NCM per network node (JCPU-640 or JNCA).

IFW-W: Intelligent Fire Workstation (network control station),

Wire. UL-Listed graphics PC with mouse, 17" color flat-screen

LCD monitor. Order as necessary for network systems. Each

IFW consumes one of 103 network addresses.

IFW-F: Intelligent Fire Workstation (network control station),

Fiber. UL-Listed graphics PC with mouse, 17" color flat-screen

LCD monitor. Order as necessary for network systems. Each

IFW consumes one of 103 network addresses.

JVeriFire-TCD: VeriFire® Tools CD-ROM. Contains program-

ming software for the IFC-640, JNCA, and XPIQ. Includes local

panel connection cable. Programming PC requires a serial port

connection.

ACM-24AT: ACS annunciator – up to 96 points of annunciation

with Alarm or Active LED, Trouble LED, and switch per circuit.

Active/Alarm LEDs can be programmed (by powered-up switch

selection) by point to be red, green, or yellow; the Trouble LED is

always yellow.

AEM-24AT: Same LED and switch capabilities as ACM-24AT,

expands the ACM-24AT to 48, 72, or 96 points.

ACM-48A: ACS annunciator – up to 96 points of annunciation

with Alarm or Active LED per circuit. Active/Alarm LEDs can be

programmed (by powered-up switch selection) in groups of 24 to

be red, green, or yellow. Expandable to 96 points with one AEM-

48A.

AEM-48A: Same LED capabilities as ACM-48A, expands the

ACM-48A to 96 points.

BAT Series: Batteries. IFC-640 utilizes two 12 volt, 12 to 55 AH

batteries. See DN-6933.

PS Series: Batteries. IFC-640 utilizes two 12 volt, 12 to 55 AH

batteries.

JCI-LBB: Battery Box (required for batteries over 25 AH).

System Capacity

• Intelligent Signaling Line Circuits ............1 expandable to 2

• Intelligent detectors .........................................159 per loop

• Addressable monitor/control modules .............. 159 per loop

• Programmable internal hardware and output circuits

(4 standard)......................................................................68

• Programmable software zones......................................... 99

• Special programming zones.............................................14

• LCD annunciators per CPU-640/-640E and JNCA

(observe power)................................................................ 32

• ACS annunciators per CPU-640/-640E

.........................................................32 address x 64 points

• ACS annunciators per JNCA

................................................32 address x 64 or 96 points

NOTE: The JNCA supports up to 96 annunciator address points

per ACM-24/48.

Specifications

• Primary input power, JCPU-640 board: 120 VAC, 50/60 Hz,

3.0 amps. JCPU-640E board: 220/240 VAC, 50/60 Hz, 1.5

Amps.

•Total output 24 V power: 6.0 A in alarm.

NOTE: The power supply has a total of 6.0 Amps of available

power. This is shared by all internal modules.

• Standard notification circuits (4): 2.5 A each.

• Four-wire detector power: 1.25 A.

• Non-resettable regulated power outputs: 1.25 A each.

• Battery charger range: 12 AH – 55 AH. Use separate cabi-

net for batteries over 25 AH.

• Optional high-capacity (25 – 120 AH) battery charger:

CHG-120 (see CHG-120 data sheet, DN-6040).

• Float rate: 27.6 V.

Temperature and Humidity Ranges

This system meets NFPA requirements for operation at 0 –

49ºC/32 – 120ºF and at a relative humidity 93% ± 2% RH

(noncondensing) at 32ºC ± 2ºC (90ºF ± 3ºF). However, the

useful life of the system's standby batteries and the electronic

components may be adversely affected by extreme tempera-

ture ranges and humidity. Therefore, it is recommended that

this system and its peripherals be installed in an environment

with a normal room temperature of 15 – 27ºC/60 – 80ºF.

Agency Listings and Approvals

The listings and approvals below apply to the basic IFC-640

control panel. In some cases, certain modules may not be listed

by certain approval agencies, or listing may be in process. Con-

sult factory for latest listing status.

•UL: S1570

•ULC: ML118

•FM APPROVED Exceptions – JCPU-640E, Proprietary

service

•CSFM: 7165-0554:143, 7170-0554:142

•MEA: 317-01-E Vol. II

•City of Chicago

Standards

The IFC-640 complies with the following UL Standards and

NFPA 72 Fire Alarm Systems requirements :

– UL 864 (Fire)

– UL 1076 (Burglary)

– LOCAL (Automatic, Manual, Waterflow and Sprinkler

Supervisory).

–AUXILIARY (Automatic, Manual and Waterflow) (requires

4XTMF).

– REMOTE STATION (Automatic, Manual and Waterflow)

(requires 4XTMF).

–PROPRIETARY (Automatic, Manual and Waterflow).

Not applicable for FM.

– EMERGENCY VOICE/ALARM.

Page 9 of 9 — JCI-6856:A • 12/01/06

AWACS™, HARSH™, NIS™, Notifier Integrated Systems™, and NO-

TI•FIRE•NET™ are all trademarks; and FlashScan®, NION®, NOTIFIER®,

ONYX®, UniNet®, VeriFire®, and VIEW® are all registered trademarks of

Honeywell International Inc.

©2006 by Johnson Controls Inc. All rights reserved. Unauthorized use of this

document is strictly prohibited.

This document is not intended to be used for installation purposes.

We try to keep our product information up-to-date and accurate.

We cannot cover all specific applications or anticipate all requirements.

All specifications are subject to change without notice.

For more information, contact Johnson Controls Field Support Center.

507 East Michigan Street, Milwaukee, WI 53202 www.johnsoncontrols.com

Made in the U.S. A.

SYSTEM SPECIFICATIONS