Johnson and Johnson Surgical Vision SIGREMM3 WHITESTAR Signature Pro System User Manual signature users manual

Abbott Medical Optics WHITESTAR Signature Pro System signature users manual

User Manual

Download: Johnson and Johnson Surgical Vision SIGREMM3 WHITESTAR Signature Pro System User Manual signature users manual
Mirror Download [FCC.gov]Johnson and Johnson Surgical Vision SIGREMM3 WHITESTAR Signature Pro System User Manual signature users manual
Document ID3204356
Application IDV6OYy3nxh8SJurUTIf+OvQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize163.63kB (2045398 bits)
Date Submitted2016-11-22 00:00:00
Date Available2017-01-07 00:00:00
Creation Date2016-11-22 09:17:27
Producing SoftwareAdobe PDF Library 10.0
Document Lastmod2016-11-22 13:43:32
Document Titlesignature users manual.book
Document CreatorAcrobat PDFMaker 10.1 for Word
Document Author: trippek

WHITESTAR SIGNATURE PRO System
8 • Error Messages Troubleshooting and Diagnostics
513 IV Pole communications error.
Probable cause: Communication error.
Corrective action:
1. Prime the system.
2. If the error still does not clear or if the error continues to occur, document the
error message and contact AMO for technical service.
514 IV Pole error.
Probable cause: Communication error.
Corrective action:
1. Prime the system.
2. If the error still does not clear or if the error continues to occur, document the
error message and contact AMO for technical service.
515 IV Pole calibration error.
Probable cause: Communication error.
Corrective action:
1. Run Self Test.
2. If the error still does not clear or if the error continues to occur, document the
error message and contact AMO for technical service.
516 IV Pole communication error.
Probable cause: Communication error.
Corrective action:
1. Prime the system.
2. If the error still does not clear or if the error continues to occur, document the
error message and contact AMO for technical service.
RX Only –NGP Z370500 Rev. B 1116
8-38
WHITESTAR SIGNATURE PRO System
8 • Error Messages Troubleshooting and Diagnostics
517 IV Pole is jammed.
Probable cause:
• IV Pole motor failure.
• There is an obstruction that does not allow the IV pole to move.
Corrective action:
1. Check the IV pole for obstructions.
2. Prime the system.
3. If the error still does not clear or if the error continues to occur, document the
error message and contact AMO for technical service.
601 Tune excessive vacuum error.
Probable cause: There is too much vacuum.
Corrective action:
1. Check tubing connections.
2. Check the handpiece. Replace the tip if needed.
3. Retune the handpiece.
4. If the error still does not clear, replace the handpiece with a new handpiece, and
tune the handpiece.
5. If the error still does not clear or if the error continues to occur, document the
error message and contact AMO for technical service.
605 Tune no handpiece error.
Probable cause: Hardware failure.
Corrective action:
1. Attach handpiece to the system.
2. Retune the handpiece.
3. If the error still does not clear, replace the handpiece with a new handpiece, and
tune the handpiece.
4. If the error still does not clear or if the error continues to occur, document the
error message and contact AMO for technical service.
RX Only –NGP Z370500 Rev. B 1116
8-39
9
WARRANTY AND MAINTENANCE
Warranty Statement
RX Only –NGP Z370500 Rev. B 1116
9-1
WHITESTAR SIGNATURE PRO System
Warranty Statement
9 • Warranty and Maintenance
Abbott Medical Optics Inc. warrants for a period of one year (12 months) from the
date of installation of the WHITESTAR SIGNATURE PRO System console, foot
pedal, wireless remote control, the programmable power pole, and the phaco
handpiece to be free from defects in materials and workmanship when properly
installed, maintained, and used for the intended purpose. In no event shall the date
of installation be deemed to occur later than six months from the date of delivery of
the WHITESTAR SIGNATURE PRO System by Abbott Medical Optics Inc. to
the common carrier.
You are required to provide AMO with prompt written notice of any defect or
defects and permit AMO to have access to the WHITESTAR SIGNATURE PRO
System within a reasonable time after notification of any defect. In the event that
you do not provide AMO with prompt notification of a defect or permit access to
the WHITESTAR SIGNATURE PRO System within a reasonable time after
notification, AMO is hereby released from all liability with reference to such defect
and subsequent damage, if any, resulting from the inability of AMO to correct such
defect.
MISUSE AND MISHANDLING ARE NOT COVERED UNDER WARRANTY.
AMO’s sole obligation is to repair or replace, at AMO’s option, the defective
part(s), which shall be returned freight prepaid to AMO by you and then returned to
you freight collect once repaired or replaced.
The irrigation/aspiration handpiece set, diathermy forceps and diathermy cord are
warranted for ninety (90) days.
This warranty applies only to the original purchaser/user of the device and may not
be transferred. This warrant will be void if and only so long as the equipment is
used in any country other than the country to which it was originally shipped by
AMO.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED
OR IMPLIED, INCLUDING WITHOUT LIMITATION THE WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO
EVENT SHALL AMO BE LIABLE TO THE PURCHASER/USER FOR
CONSEQUENTIAL, SPECIAL, INCIDENTAL, OR PUNITIVE DAMAGES,
LOSS OF PROFITS OR LOSS OF USE. The liability of AMO for breach of this
warranty shall, in any case, be limited to the total amount paid by you for the
WHITESTAR SIGNATURE PRO System furnished by AMO and any work
performed by AMO in connection therewith.
Extended Warranty
Extended warranty contracts (excluding the phaco handpiece) are available. Contact
AMO for information on the availability of an extended warranty contract.
Note:
If outside the United States, contact your local AMO office or
representative for warranty information.
RX Only –NGP Z370500 Rev. B 1116
9-2
WHITESTAR SIGNATURE PRO System
9 • Warranty and Maintenance
Maintenance
User maintenance of the WHITESTAR SIGNATURE PRO System is only for
those adjustments and corrective actions in the Error Messages and
Troubleshooting, and Diagnostics sections of this manual. There are no user
serviceable components within the console and you must not attempt to access the
internal components. Any attempt to do so will void the warranty.
AMO recommends, at least annually, routine or periodic maintenance of the
WHITESTAR SIGNATURE PRO System by an AMO representative. AMO
recommends the measurement of PE resistance and leakage current according to
IEC 601-1 every two years.
If a problem continues following setup, check-out and troubleshoot as per the
procedures in this manual, then contact AMO for corrective action
(1-877-AMO-4-LIFE in USA 1-877-266-4543 or 1-800-511-0911 for outside the
USA).
RX Only –NGP Z370500 Rev. B 1116
9-3
10
SPECIFICATIONS
Physical Specifications
Environmental Specifications
Electrical Specifications
Phacoemulsification Specifications
Irrigation and Aspiration Specifications
Vitrectomy Specifications
Diathermy Specifications
Diathermy Power Graphs
Diathermy Power versus Load Impedance
Phaco Power Graphs
Phaco Tip Velocity
Bottle Height Pressure
RX Only – NGP Z370500 Rev. B 1116
10-1
WHITESTAR SIGNATURE PRO System
Physical
Specifications
10 • Specifications
Table 10.1 – System Physical Specifications
English / U.S.
Metric:
Width
24 inches
61 cm
Depth
24 inches
61 cm
Height
59 inches
150 cm
Power cord length
20 feet
6 meters
Electrical enclosure current
leakage
IEC 60601-1
compliance
UL 60601-1
Weight (including IV pole)
185 pounds
84 kg
Width
12 inches
31 cm
Length
10.5 inches
27 cm
Height
5.5 inches
14 cm
10.0 pounds
4.5 kg
Width
10.5 inches
27 cm
Length
14 inches
36 cm
Height
5.5 inches
14 cm
Weight
15 pounds
7 kg
Cord Length
11.8 feet
36 cm
Width
9.82 inches
25 cm
Length
15.57 inches
39.6 cm
Height
4.88 inches
12.4 cm
Weight
13 pounds
5 kg
Cord Length
12 feet
366 cm
Maximum travel
41 inches
106 cm
Velocity
2.4 inches/sec
6 cm/sec.
Maximum lift weight
2.43 pounds
1.1 kg
WHITESTAR
SIGNATURE PRO
System Console
Console dimensions (with
display)
Foot Pedal
Single Linear Foot Pedal
Dimensions
Weight
Advanced Control Pedal
Dimensions
Advance Linear Pedal
Dimensions
Programmable IV Pole
RX Only – NGP Z370500 Rev. B 1116
10-2
WHITESTAR SIGNATURE PRO System
10 • Specifications
English / U.S.
Metric:
Width
5 inches
13 cm
Length
5 inches
13 cm
Height
1.5 inches
4 cm
Weight
2.0 pounds
.9 kg
Wireless Remote Control
Environmental
Specifications
Table 10.2 – Environmental Specifications
Environmental Specifications
Storage/Transportation Conditions
Electrical
Specifications
System
Operating Temperature
10 to 40°C
Humidity
Up to 95% RH, non-condensing
Ambient Pressure
See Vitrectomy Specifications for
additional information.
Storage Temperature
-20 to 60°C
Humidity
Up to 95% RH, non-condensing
Table 10.3 – Electrical Specifications
Voltage
Frequency
Rated Power
Fuse Rating
Enclosure
Current Leakage
100-240 Vac
50-60 Hz
750 VA
6.3A, 250V,
Bussman
GDA
<500 µA
Phacoemulsification
Specifications
Table 10.4 – Phacoemulsification Specifications
Peristaltic Pump
Venturi Pump
Phaco Power
1%-5% in 1% increments,
5-100%, in 5% increments
Vacuum Level
0–650 mmHg in 5 mmHg
increments
Pump Flow Rate
0-60 cc/minute
Vacuum Level
0-600 mmHg in 5 mmHg
increments
RX Only – NGP Z370500 Rev. B 1116
10-3
WHITESTAR SIGNATURE PRO System
Irrigation and
Aspiration
Specifications
10 • Specifications
Table 10.5 – Irrigation and Aspiration Specifications
Peristaltic Pump
Venturi Pump
Vitrectomy
Specifications
Vacuum Level
0–650 mmHg in 5 mmHg
increments
Pump Flow
0-60 cc/minute
Vacuum Level
0-600 mmHg in 5 mmHg
increments
Table 10.6 – Vitrectomy Specifications
Peristaltic Pump
Vacuum Level
0–650 mmHg in 5 mmHg
increments
Pump Flow Rate
10-60 cc/minute, in 1 cc
increments
Venturi Pump
Vacuum Level
0-600 mmHg in 5 mmHg
increments
Atmospheric
Pressure/Altitude
Density Altitude (DA) conditions are 2,500 cpm
from sea level to 3,000 feet (914.4 m) elevation and
shall be de-rated by 100cpm per 1,000ft (304.8 m)
additional elevation up to a maximum of 10,000 ft
above sea level.
Indicated Cut Rate
Actual Cut Rate
Upper Limit (cpm)
Actual Cut Rate Lower
Limit (cpm)
2500
3000
2000
RX Only – NGP Z370500 Rev. B 1116
10-4
WHITESTAR SIGNATURE PRO System
Diathermy
Specifications
10 • Specifications
Table 10.7 – Diathermy Specifications
Power Adjustment
5% to 100%, in 5% increments
Diathermy Power (maximum power
into rated load)
8.5 Watts into 350 Ohms 386 kHz
Diathermy Type
Bipolar
Rated Peak Voltage
160 Volts
Connector of diathermy forcep/
probe
Ø.072 RECEPTACLE (2)
All measurements are in inches.
RX Only – NGP Z370500 Rev. B 1116
10-5
WHITESTAR SIGNATURE PRO System
10 • Specifications
Diathermy Power
Graphs
Figure 10.1 – Diathermy Output Power (Typical) 10 Ohm
Y Axis = Watts
X Axis = Settings
Figure 10.2 – Diathermy Output Power (Typical) 50 Ohm
Y Axis = Watts
X Axis = Settings
RX Only – NGP Z370500 Rev. B 1116
10-6
WHITESTAR SIGNATURE PRO System
10 • Specifications
Figure 10.3 – Diathermy Output Power (Typical) 200 Ohm
Y Axis = Watts
X Axis = Settings
Figure 10.4 – Diathermy Output Power (Typical) 350 Ohm
Y Axis = Watts
X Axis = Settings
RX Only – NGP Z370500 Rev. B 1116
10-7
WHITESTAR SIGNATURE PRO System
10 • Specifications
Figure 10.5 – Diathermy Output Power (Typical) 500 Ohm
Y Axis = Watts
X Axis = Settings
Figure 10.6 – Diathermy Output Power (Typical) 1000 Ohm
Y Axis = Watts
X Axis = Settings
RX Only – NGP Z370500 Rev. B 1116
10-8
WHITESTAR SIGNATURE PRO System
Diathermy Power
versus Load
Impedance
10 • Specifications
Figure 10.7 – Diathermy Output Power (50% Setting)
Y Axis = Watts
X Axis = Impedance (Ohms)
Figure 10.8 – Diathermy Output Power (100% Setting)
Y Axis = Watts
X Axis = Impedance (Ohms)
RX Only – NGP Z370500 Rev. B 1116
10-9
WHITESTAR SIGNATURE PRO System
Phaco Power
Graphs
10 • Specifications
Figure 10.9 – Longitudinal Phaco Power
Y Axis = Output Power (Watts)
X Axis = GUI Settings %
Figure 10.10 – ELLIPS FX Phaco Power Linear Mode
Y Axis = Power (Watts)
X Axis = GUI Settings %
RX Only – NGP Z370500 Rev. B 1116
10-10
WHITESTAR SIGNATURE PRO System
Phaco Tip Velocity
Bottle Height
Pressure
10 • Specifications
Nominal Velocity for the ELLIPS FX handpiece and the WHITESTAR
handpiece at 100% power, continuous, with the OPOR3020L phaco tip is shown in
the following table.
Handpiece
Nominal Longitudinal Velocity (m/s)
ELLIPS FX (690880 (A))
8.85
WHITESTAR (690697 (A))
11.13
The WHITESTAR SIGNATURE PRO System has a built in IV pole to generate
positive pressure using balanced salt solution to provide positive irrigation fluid.
Measurement points:
• All measurements are taken with a pressure meter at the same height as the
pressure sensor in the WHITESTAR SIGNATURE PRO System.
• This position is defined as 41 inches or 101.6 cm from the floor.
1. Center of Drip Chamber
2. Center of pressure sensor is 41 inches or 104.2 cm from the floor
RX Only – NGP Z370500 Rev. B 1116
10-11
WHITESTAR SIGNATURE PRO System
10 • Specifications
An IV bottle height reported as 0 cm includes an offset of 7.9 inches or 20 cm to
make sure that a positive pressure is always provided.
Table 10.8 – Expected Pressure as a function of Bottle Height
Bottle Height cm
Theoretical Pressure mmHg
Corrected Pressure At
Patient Eye Level mmHg
0.00
14.80
20
14.80
29.60
40
29.60
44.40
60
44.40
59.20
80
59.20
74.00
100
74.00
88.80
105
77.70
92.50
RX Only – NGP Z370500 Rev. B 1116
10-12
11
ACCESSORIES AND PARTS
REORDERING
Accessories and Parts List
RX Only – NGP Z370500 Rev. B 1116
11-1
WHITESTAR SIGNATURE PRO System
11 • Accessories and Parts Reordering
Table 11.1 – WHITESTAR SIGNATURE PRO System Part Number
Name
WHITESTAR SIGNATURE PRO
Console
List of Accessories
with Part Numbers
Description
An ophthalmic microsurgical system.
Part number
NGP680301
The following table is a list of accessories that you can use to reorder parts for your
WHITESTAR SIGNATURE PRO System. Your AMO representative can advise
you of recommended inventory levels based your facility's volume of
phacoemulsification procedures. You can order any of the items listed below
through your AMO representative or directly through AMO customer service. Your
AMO representative can confirm the availability of these items in your area.
Table 11.2 – Accessories and Parts List
System
Accessories
Phaco
Handpiece
I/A
Handpiece
Part Number
Description
690697
WHITESTAR Phaco Handpiece, Coaxial
690880
ELLIPS FX Phaco Handpiece
OPOR0019L
19 Gauge LAMINAR Flow Phaco Tip, 0° Round Tip
OPOR1519L
19 Gauge LAMINAR Flow Phaco Tip, 15° Round Tip
OPOR3019L
19 Gauge LAMINAR Flow Phaco Tip, 30° Round Tip
OPOR4519L
19 Gauge LAMINAR Flow Phaco Tip, 45° Round Tip
OPOR0020L
20 Gauge LAMINAR Flow Phaco Tip, 0° Round Tip
OPOR1520L
20 Gauge LAMINAR Flow Phaco Tip, 15° Round Tip
OPOR3020L
20 Gauge LAMINAR Flow Phaco Tip, 30° Round Tip
OPOR4520L
20 Gauge LAMINAR Flow Phaco Tip, 45° Round Tip
OPOCR3019L
Disposable LAMINAR Flow Phaco Tip, 19 Gauge, 30° Curved
OPOCR3020L
Disposable LAMINAR Flow Phaco Tip, 20 Gauge, 30° Curved
OPOS19L
19 Gauge LAMINAR Flow Irrigation Sleeve and Test Chamber
OPOS20L
20 Gauge LAMINAR Flow Infusion Sleeve and Test Chamber
OPOMTWL
LAMINAR Flow Tip Wrench
OPOIA20CRV
SOLO I/A Handpiece, 20 Ga., Curved Silicone Sleeve Tip
OPOIA2045D
SOLO I/A Handpiece, 20 Ga., 45° Silicone Sleeve Tip
OPOIA20STR
SOLO I/A Handpiece, 20 Ga., Straight Silicone Sleeve Tip
OPOIA20KIT
SOLO I/A Handpiece Kit
OM055002
PHACOFIT Titanium Handle
OM05510110
PHACOFIT I/A Tip Curved 0.5 mm Port
RX Only – NGP Z370500 Rev. B 1116
11-2
WHITESTAR SIGNATURE PRO System
System
Accessories
Diathermy
Handpiece
Vitrectomy
Cutter
11 • Accessories and Parts Reordering
Part Number
Description
OM05510112
PHACOFIT O-Ring's I/A Tip (5PK)
OM05510113
PHACOFIT Titanium, Multi-Tip Set
OM05510114
PHACOFIT Cleaning/Flushing Kit
OM05510115
PHACOFIT Tip, Luer Adapter (Aspiration)
OM05510116
PHACOFIT Tip, 45 Degree Silicone (No Sleeve)
OM0551011
PHACOFIT I/A Tip Straight 0.3 MM Port
OM0551012
PHACOFIT I/A Tip Curved 0.3 mm Port
OM0551013
PHACOFIT I/A Tip 45 Degree 0.3 mm Port
OM0551014
PHACOFIT I/A Tip 90 Degree 0.3 mm Port
OM0551015
PHACOFIT I/A Tip Binkhorst 0.3 mm Port
OM0551016
PHACOFIT I/A Tip Straight SI 0.3 mm Port
OM0551017
PHACOFIT I/A Luer Adapter, F/F
OM0551018
PHACOFIT I/A Tip Curved, SI, 0.3 mm Port
OM0551019
PHACOFIT I/A Tip Straight 0.5 MM Port
OM0551020J
PHACOFIT Athlete I/A Tip Straight Type
OM0551021J
PHACOFIT Athlete I/A Tip 45 Degree Type
DUA02020
DUET STARTER KIT, 20GA
DU02100
DUET ASPIRATION HANDLE
DU02200
DUET IRRIGATION HANDLE
DU02301
DUET 20G CURVED IRRIGATOR CLOSED END
DU02302
DUET 20G CURVED ASPIRATION 0.3MM PORT CAP POL
DU02303
DUET 19G FINE IRRIGATING CHOPPER
DU02305
DUET 20G OLSON II IRRIGATING CHOPPER
DU02325
DUET MST Aguirre Duet Tip
DU02335
DUET MST Fine/Nagahara Tip
SCP680600
Diathermy Power Cable
K121085
Bipolar Forceps, Curved Iris 0.5 mm Tip
K147000
18 Gauge Straight Diathermy Pencil, reusable
NGP0020
20 gauge Vitreous Cutter
NGP0023
23 gauge Vitreous Cutter
NGP0025
25 gauge Vitreous Cutter
RX Only – NGP Z370500 Rev. B 1116
11-3
WHITESTAR SIGNATURE PRO System
System
Accessories
FUSION
Pack
11 • Accessories and Parts Reordering
Part Number
Description
OPO70
FUSION Pack (disposable, sterile)
OPO71
FUSION Dual Pump Pack (disposable, sterile)
Wireless
Remote
Control
NGP680137
WHITESTAR SIGNATURE PRO System Remote Control
0100-1834
AC Charger, SIGNATURE Wireless Remote
Foot Pedal
NGP680701
WHITESTAR SIGNATURE System Single Linear Foot Pedal
NGP680702
WHITESTAR SIGNATURE System Advanced Control Pedal
NGP680703
WHITESTAR SIGNATURE PRO System Advanced Linear Foot
Pedal
0100-1835
AC Charger, SIGNATURE Wireless Foot Pedal
0100-0055
CABLE ASSY, WHITESTAR SERIES FOOT PEDAL
(Single Linear Foot Pedal and Advanced Control Pedal)
Miscellaneous
Operator’s
Manual
0100-6303
Cable Assy, Advanced Linear Foot Pedal to Console, Signature
0100-1836
LI-BATTERY, SIGNATURE PRO Advanced Linear Pedal
2410-0049-L
Power cord, hospital grade, 20 ft., 6.1 meters
OM05510114
I/A Cleaning Kit
0100-0750
WHITESTAR SIGNATURE System Dust Cover
MSR309
Sterilization Tray
NGP Z370494
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Bulgarian)
NGP Z370495
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Chinese)
NGP Z370496
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Czech)
NGP Z370497
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Croatian)
NGP Z370498
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Danish)
NGP Z370499
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Dutch)
NGP Z370500
WHITESTAR SIGNATURE PRO System Operator’s Manual
(English)
NGP Z370501
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Estonian)
NGP Z370502
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Finnish)
NGP Z370503
WHITESTAR SIGNATURE PRO System Operator’s Manual
(French)
RX Only – NGP Z370500 Rev. B 1116
11-4
WHITESTAR SIGNATURE PRO System
System
Accessories
11 • Accessories and Parts Reordering
Part Number
Description
NGP Z370504
WHITESTAR SIGNATURE PRO System Operator’s Manual
(German)
NGP Z370505
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Greek)
NGP Z370506
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Hungarian)
NGP Z370507
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Italian)
NGP Z370508
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Japanese)
NGP Z370509
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Korean)
NGP Z370510
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Latvian)
NGP Z370511
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Lithuanian)
NGP Z370512
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Norwegian)
NGP Z370513
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Polish)
NGP Z370514
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Portuguese)
NGP Z370515
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Portuguese-Brazilian)
NGP Z370516
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Romanian)
NGP Z370517
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Russian)
NGP Z370518
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Serbian)
NGP Z370519
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Slovakian)
NGP Z370520
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Slovenian)
NGP Z370521
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Spanish)
NGP Z370522
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Swedish)
NGP Z370523
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Turkish)
RX Only – NGP Z370500 Rev. B 1116
11-5
WHITESTAR SIGNATURE PRO System
System
Accessories
11 • Accessories and Parts Reordering
Part Number
Description
NGP Z370526
WHITESTAR SIGNATURE PRO System Operator’s Manual
(Traditional Chinese)
NGP Z370524
WHITESTAR SIGNATURE PRO System Operator’s Manual
CD, Multilingual
RX Only – NGP Z370500 Rev. B 1116
11-6
12
INDEX
Accessories 11-1
Add a Surgeon 4-3
Advanced Control Pedal 1-4, 1-18, 2-5, 10-2
Calibration 4-23
Connections 4-17
Default Settings 4-16
Setup 4-16
Switch Assignment 4-17
Testing 4-23
Threshold Configuration 4-22
Advanced Linear Pedal 1-4, 2-5
Battery Replacement 8-4
Connections 4-25
Handle 2-7
Setup 4-25
Switch Assignment 4-26
Test 4-32
Threshold Configuration 4-30
Anterior chamber too deep 8-9
Anterior Segment
Surgery 3-2
Aspiration
Specifications 10-4
Aspiration Rate
Occlusion 5-24
Assign Order
Program 5-29
Surgeon 4-35
Back-light button 8-7
Backup All 6-21
Balance
Irrigation/Aspiration 3-14
Batteries
Remote control 2-9
Battery
Charging 4-16, 4-25, 8-6
Replacement 8-4
Begin Tune 3-13
Blocked
Aspiration port 5-26
BLUETOOTH 8-7
Bottle Height
IA 5-11
Phaco 5-8
Vitrectomy 5-12
Bypass 3-11, 3-15
Calibrate
Foot Pedal
Advanced Control Pedal 4-23
Single Linear 4-14
Touch Screen 6-11
CASE Mode 5-26
CASE ONE Touch 1-7, 5-27
CASE Vacuum 5-27
Chamber partially collapses 8-11
Changing
Mode Parameters 3-16
Charging
Battery 4-16, 4-25, 8-6
Checkout
System 3-17
Cleaning
Touch Screen 7-2
Cleaning/Care 7-2
Common Problems 8-2
Connecting Handpieces 1-9
RX Only – NGP Z370500 Rev. B 1116
12-1
WHITESTAR SIGNATURE PRO System
12 • Index
Connections
Advanced Control Pedal 4-17
Front Panel 3-2
Rear Panel 3-3, 4-8
Console Dimensions 10-2
Continuous Burst 5-13
Phaco Power 5-15
Continuous Irrigation 1-5, 3-11
Cup Fill 3-10
Continuous Phaco Power 5-14
Copy a Program 5-29
Create
Surgeon 5-2
Cup Fill 3-10
Custom Duty Cycles 5-16
Cut Mode
Vitrectomy 5-12
Cut Rate
Vitrectomy 5-12
Cutter
Vitrectomy 3-7
Diathermy 1-7, 1-10
Default Settings 5-12
Forceps 3-6
Handpiece 3-6, 7-2
Output Power 10-9
Diathermy Handpiece
Part Numbers 11-3
Dimensions 10-2
Dual Pump 1-5
Duty Cycles 5-15
Database
Delete 6-25
Import/Export 6-19
Restore 6-23, 6-25
Date
Set 6-16
Default Settings
Diathermy 5-12
Foot Pedal
Advanced Control Pedal 4-16
Single Linear 4-7
Irrigation/Aspiration 5-11
Phaco 5-8
Vitrectomy 5-12
Delete
Database 6-25
Program 5-2, 5-28
Delete a Backup Database 6-25
Diagnostics 8-1
Edit
Program 5-3
Surgeon 4-4
Effective Phaco Time 3-21
Electrical
Specifications 10-3
ELLIPS Handpiece 1-4, 3-4, 3-5
End Case 3-21
Environmental
Specifications 10-3
EPT 3-21
Export 6-19
Failed to pair 8-8
Feedback
Foot Pedal 4-7
Fluidics 1-3
Fluidics Mode
Phaco 5-8
RX Only – NGP Z370500 Rev. B 1116
12-2
WHITESTAR SIGNATURE PRO System
12 • Index
Foot Pedal 1-4
Advanced Control Pedal 1-18
Calibrate 4-23
Connections 4-17
Default Settings 4-16
Setup 4-16
Switch Assignment 4-17
Testing 4-23
Threshold Configuration 4-22
Advanced Linear Pedal 2-5
Configuration 4-30
Connections 4-25
Setup 4-25
Test 4-32
Feedback 4-7
Modes
Vitrectomy 5-6
Part Number 11-4
Pitch 2-7
Pitch Regions 4-7
Positions 2-7, 5-16
Single Linear 1-4, 2-5
Calibration 4-14
Default Settings 4-7
Setup 4-6
Switch Assignment 4-9
Testing 4-14
Threshold Configuration 4-12
Specifications 10-2
Forceps 9-2
Diathermy 3-6
Front Panel 3-2
Fuse
Replacement 8-2
FUSION 5-26
FUSION Fluidics 5-20, 5-22, 5-26
FUSION Tubing Pack 2-3, 11-4
Graphic User Interface 1-5
Graphs
Phaco Power 10-10
GUI 1-5
Handle
Advanced Linear Pedal 2-7
Handpiece
Cleaning 7-2
Connecting 1-9
IA 3-6
Phaco 3-5
Setup
Diathermy 3-6
I/A 3-6
Phaco 3-4
Vitrectomy 3-7
Ultrasonic 1-9
Warranty 9-2
Help 8-14
High Power
Limit 5-19
High Power Pulse
Phaco Power 5-14
IA
Handpiece 3-6
IAC 5-6
ICA 5-6
ICE Pulse Shaping
WHITESTAR Technology 5-19
Import 6-20
Import/Export Database 6-19
Inspection Instructions 2-2
Install Tubing Cassette 3-9
Irrigation
Changing 1-8
Continuous 3-11
Flow does not stop 8-9
Inadequate 1-9
Irrigation/Aspiration 1-7
Balance 3-14
Default Settings 5-11
RX Only – NGP Z370500 Rev. B 1116
12-3
WHITESTAR SIGNATURE PRO System
12 • Index
IV Pole
Does not work 8-8
Programmable 1-10, 2-8
Setup 3-3
Testing 6-3
Monitor Drape 2-3
Multiple Burst
Phaco Power 5-15
Power 5-13
Multiple Mode Programming 1-6
Kick 5-19
No aspiration 8-10
No diathermy or poor diathermy 8-13
No phacoemulsification 8-12
No sound when using diathermy 8-13
No vitrectomy cutting 8-13
LAMINAR Flow 3-6
Language Selection 6-14
Locked Program 5-28
Long Pulse
Phaco Power 5-14
Power 5-13
Low batteries 8-8
Low Power
Limit 5-19
Low Power Pulse
Phaco Power 5-14
Lower Threshold 5-27
Maintenance 9-3
Max Aspiration
IA 5-11
Vitrectomy 5-12
Max Power
Diathermy 5-12
Max Vacuum
IA 5-11
Vitrectomy 5-12
Maximum Height
IV Pole 6-2
Maximum Vacuum 5-20
Mayo Tray Drape 2-3
Miscellaneous Part Numbers 11-4
Mode Programming 1-6
Modes
Changing Parameters 3-16
Occluded Aspiration Rate 5-21
Occlusion
Aspiration Rate 5-24
Vacuum Threshold 5-24
Venting 5-26
Occlusion Mode Phaco
Settings 5-21
One Touch
CASE 5-27
Operating Modes 1-6
Output Power
Diathermy 10-9
Pairing
Remote Control 6-10
Wired 6-7
Wireless 6-5
Wireless Remote Control 8-7
Panel
Front 3-2
Rear 3-3
Parameter Settings
WHITESTAR Technology 5-16
Parameters
Programming 1-5
Parts 11-1
RX Only – NGP Z370500 Rev. B 1116
12-4
WHITESTAR SIGNATURE PRO System
12 • Index
Passive Reflux 5-28
Pencil Probe
Diathermy 3-6
Percent Kick
High End of Range 5-19
Low End of Range 5-19
Peristaltic Pump 10-4
Phaco
Default Settings 5-8
Handpiece 3-4
Phaco Handpiece 1-4, 1-10, 3-4, 3-5, 7-2
Part Numbers 11-2
Phaco Power
Continuous 5-14
Graph 10-10
Phacoemulsification 1-2, 1-6, 1-9, 3-4, 8-12
Physical Specifications 10-2
Pitch 2-7
Pitch Regions
Foot Pedal 4-7
Poor aspiration 8-10
Poor phacoemulsification 8-12
Positions
Foot Pedal 2-7
Power
Continuous Burst 5-13
Cord Length 10-2
Failure 1-9
Long Pulse 5-13
Multiple Burst 5-13
Short Pulse 5-13
Single Burst 5-13
Switch 8-2
Power Delivery
Diathermy 5-12
pps 5-14
Precautions
Safety 1-8
Prime
Bypass 3-11
Prime/Tune 1-5, 3-10, 3-11
Priming
Vitrectomy 3-15
Program
Assign Order 5-29
Delete 5-2
Lock 5-28
Locked 5-28
Select 3-8
Program Name
Edit 5-3
Programmable IV Pole 1-6, 1-10, 2-8
Setup 3-3
Specifications 10-2
Testing 6-3
Pulse
Off Time 5-16
On time 5-16
Pulses per second 5-14
Rate 5-16
Pulse Shaping 5-18
Pump Ramp Threshold
IA 5-11
Rear Panel 3-3
Reduced/insufficient irrigation flow 8-9
Reflux 5-28
Passive 5-28
Remote Control
Pairing 6-10
Wireless 2-8
Remote Control, Wireless
Setup 6-5
Reordering 11-1
Replacing
Batteries 1-14
Fuse 8-2
Reset
Timers 3-14, 3-18
Restore
Database 6-25
Restore All 6-24
Restore Database 6-23
Restriction of Hazardous Substances 1-22
RoHS 1-22
RX Only – NGP Z370500 Rev. B 1116
12-5
WHITESTAR SIGNATURE PRO System
12 • Index
Screen, Touch
Calibrate 6-11
Selecting a Language 6-14
Self Test 3-8
Service Interval 6-18
set vacuum units 1-7
Settings
Occlusion Mode 5-21, 5-25
Post Laser Cataract 5-10
Setup
Advanced Control Pedal 4-16
Surgical Media Center (SMC) 6-15
System 3-2
Wireless Remote Control 6-5
Short Pulse
Phaco Power 5-14
Power 5-13
Shutdown
Sequence 3-20
System 3-20
Side vitrectomy 5-6
Single Burst
Phaco Power 5-15
Power 5-13
Single Linear Foot Pedal
Calibration 4-14
Default Settings 4-7
Setup 4-6
Switch Assignment 4-9
Testing 4-14
Threshold Configuration 4-12
Sleep Mode 8-7
SMC (Surgical Media Center) 2-9
Software Versions
View 6-12
SOLO Handpiece 3-6
Sounds
Set and test 4-33
Specifications
Electrical 10-3
Environmental 10-3
Foot Pedal 10-2
Fuse 8-2
IA 10-4
IV Pole 10-2
Phacoemulsification 10-3
Physical 10-2
Vitrectomy 10-4
Startup 3-8
Status 8-14
Sterilization 3-20
Storage Conditions 10-3
Surgeon
Add 4-3, 5-2
Assign Order 4-35
Copy 5-29
Surgical Media Center (SMC) 2-9
Setup 6-15
Switch Assignment
Advanced Control Pedal 4-17
Advanced Linear Pedal 4-26
Single Linear Foot Pedal 4-9
Symbol Definitions 1-15
System
Checkout 3-17
Components 2-2
Console 1-5
Description 1-2
Disposal 1-22
Does not turn on 8-7
Self Test 3-8
Shutdown 3-20
System Date and Time 6-16
System Self Test 6-13
Technical Service 8-2
Test
Advanced Control Pedal 4-23
Advanced Linear Pedal 4-32
Foot Pedal
Single Linear 4-14
System 6-13
Wireless Remote Control 6-10
Test Chamber 2-3, 11-2
RX Only – NGP Z370500 Rev. B 1116
12-6
WHITESTAR SIGNATURE PRO System
12 • Index
Threshold
Vacuum 5-24
Threshold Configuration
Advanced Control Pedal 4-22
Advanced Linear Pedal 4-30
Single Linear Foot Pedal 4-12
Time
Set 6-16
Timers
Reset 3-14
Touch Screen
Calibrate 6-11
Cleaning 7-2
Does not respond 8-8
Using 3-16
Tubing Cassette 2-3
Install 3-9
Tune 3-11
Begin 3-13
Venturi pump 5-27
View Software Versions 6-12
Vitrectomy 1-7, 1-10, 3-7
Advanced Control Pedal Modes 4-17
Cutter 1-10
Default Settings 5-12
Foot Pedal Modes 4-7
Handpiece 3-7
Prime 3-15
Ultrasonic (U/S) Time 3-21
Ultrasonic Handpiece 1-9
Units of Measure 6-17
Units of measure
Set units of measure for vacuum 6-17
Unpair 8-7
Up Time
Threshold 5-27
Upper Threshold 5-27
Using
too much fluid 8-10
Touch Screen 3-16
Wake-up 2-5
Warnings 1-8, 1-11
WHITESTAR ICE Technology 1-3
WHITESTAR Technology 1-2, 5-15
Wired Pairing 6-7
Wireless Pairing 6-5
Wireless Remote Control 1-4, 1-11, 2-8
Does not pair 8-7
Part Number 11-4
Wireless Remote Test 6-10
Wireless Setup
Foot Pedal 6-5
Remote Control 6-5
Yaw 2-7
Vacuum
monitoring 5-20
pressure 5-26
Set units of measure 6-17
Vacuum units 1-7
Venting
Occlusion 5-26
RX Only – NGP Z370500 Rev. B 1116
12-7
WHITESTAR SIGNATURE PRO System
12 • Index
RX Only – NGP Z370500 Rev. B 1116
12-8
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Author                          : trippek
Create Date                     : 2016:11:22 09:17:27-08:00
Modify Date                     : 2016:11:22 13:43:32-08:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2016:11:22 13:43:32-08:00
Creator Tool                    : Acrobat PDFMaker 10.1 for Word
Document ID                     : uuid:f06fa182-a2e4-4022-93f2-f1f9c199b7d0
Instance ID                     : uuid:8757910b-494f-403d-bb1f-88c348cc19d9
Subject                         : 16
Format                          : application/pdf
Title                           : signature users manual.book
Creator                         : trippek
Producer                        : Adobe PDF Library 10.0
Source Modified                 : D:20161122171607
Company                         : Abbott Laboratories
Created                         : D:20150614
Last Saved                      : D:20161115
Page Layout                     : OneColumn
Page Count                      : 33
EXIF Metadata provided by EXIF.tools
FCC ID Filing: VGESIGREMM3

Navigation menu