Juniper Networks AX411 Wireless Access Point User Manual END USER LICENSE AGREEMENT

Juniper Networks Wireless Access Point END USER LICENSE AGREEMENT

UserManual.wiki >

Juniper Networks >

AX411 User Manual

User Manual

Getting Started Guide Getting Started Guide Use the instructions in this guide to help you install the AX411 Access Point. For details, see the AX411 Access Point Hardware Guide and the JUNOS Software WLAN Configuration and Administration Guide athttp://www.juniper.net/techpubs/a072.html.For translated documentation in Arabic, German, Spanish, French, Chinese, Korean, Russian, and Japanese, see the URL below.AX411 Access PointAX411 Access Point Front Panel1. Power Connector2. PoE Ethernet Port3. Console Port4. Lock Slot5. LEDs:•Power (Green = Power OK)•Status (Green = Managed)•5 GHz Radio (Blue = Enabled)•2.4 GHz Radio (Green = Enabled)AX411 Access Point Rear Panel1. Antennas (3)2. Mounting Bracket Locking ScrewCONNECTING THE ACCESS POINT AND CONFIGURING THE SRX SERIES DEVICEUse the instructions below to connect the AX411 Access Point to the SRX Series Services Gateway that manages it and to configure the SRX Series device.Step 1Install the antennas and connect the access point to an Ethernet port on the SRX Series Services Gateway. If you are not using a Power over Ethernet (PoE) port on the services gateway, also connect the device to the optional power supply.Note: The services gateway must be running JUNOS Software Release 10.0 or later.g033103Omit the power supply if connecing the access point to a Power over Ethernet (PoE) port.http://www.juniper.net/techpubs/a073.html112154321

Juniper NetworksSecurity Products Safety GuideSeptember 2008Juniper Networks, Inc.1194 North Mathilda AvenueSunnyvale, California 94089USA408-745-2000www.juniper.netPart Number: 530–014149–01, Revision 03Published: 2009-10-21

END USER LICENSE AGREEMENTREAD THIS END USER LICENSE AGREEMENT (“AGREEMENT”) BEFORE DOWNLOADING, INSTALLING, OR USING THE SOFTWARE. BY DOWNLOADING,INSTALLING, OR USING THE SOFTWARE OR OTHERWISE EXPRESSING YOUR AGREEMENT TO THE TERMS CONTAINED HEREIN, YOU (AS CUSTOMEROR IF YOU ARE NOT THE CUSTOMER, AS A REPRESENTATIVE/AGENT AUTHORIZED TO BIND THE CUSTOMER) CONSENT TO BE BOUND BY THISAGREEMENT. IF YOU DO NOT OR CANNOT AGREE TO THE TERMS CONTAINED HEREIN, THEN (A) DO NOT DOWNLOAD, INSTALL, OR USE THE SOFTWARE,AND (B) YOU MAY CONTACT JUNIPER NETWORKS REGARDING LICENSE TERMS.1. The Parties. The parties to this Agreement are (i) Juniper Networks, Inc. (if the Customer’s principal office is located in the Americas) or Juniper Networks(Cayman) Limited (if the Customer’s principal office is located outside the Americas) (such applicable entity being referred to herein as “Juniper”), and (ii)the person or organization that originally purchased from Juniper or an authorized Juniper reseller the applicable license(s) for use of the Software (“Customer”)(collectively, the “Parties”).2. The Software. In this Agreement, “Software” means the program modules and features of the Juniper or Juniper-supplied software, for which Customerhas paid the applicable license or support fees to Juniper or an authorized Juniper reseller, or which was embedded by Juniper in equipment which Customerpurchased from Juniper or an authorized Juniper reseller. “Software” also includes updates, upgrades and new releases of such software. “EmbeddedSoftware” means Software which Juniper has embedded in or loaded onto the Juniper equipment and any updates, upgrades, additions or replacementswhich are subsequently embedded in or loaded onto the equipment.3. License Grant. Subject to payment of the applicable fees and the limitations and restrictions set forth herein, Juniper grants to Customer a non-exclusiveand non-transferable license, without right to sublicense, to use the Software, in executable form only, subject to the following use restrictions:a. Customer shall use Embedded Software solely as embedded in, and for execution on, Juniper equipment originally purchased by Customer from Juniperor an authorized Juniper reseller.b. Customer shall use the Software on a single hardware chassis having a single processing unit, or as many chassis or processing units for which Customerhas paid the applicable license fees; provided, however, with respect to the Steel-Belted Radius or Odyssey Access Client software only, Customer shall usesuch Software on a single computer containing a single physical random access memory space and containing any number of processors. Use of theSteel-Belted Radius or IMS AAA software on multiple computers or virtual machines (e.g., Solaris zones) requires multiple licenses, regardless of whethersuch computers or virtualizations are physically contained on a single chassis.c. Product purchase documents, paper or electronic user documentation, and/or the particular licenses purchased by Customer may specify limits toCustomer’s use of the Software. Such limits may restrict use to a maximum number of seats, registered endpoints, concurrent users, sessions, calls,connections, subscribers, clusters, nodes, realms, devices, links, ports or transactions, or require the purchase of separate licenses to use particular features,functionalities, services, applications, operations, or capabilities, or provide throughput, performance, configuration, bandwidth, interface, processing,temporal, or geographical limits. In addition, such limits may restrict the use of the Software to managing certain kinds of networks or require the Softwareto be used only in conjunction with other specific Software. Customer’s use of the Software shall be subject to all such limitations and purchase of all applicablelicenses.d. For any trial copy of the Software, Customer’s right to use the Software expires 30 days after download, installation or use of the Software. Customermay operate the Software after the 30-day trial period only if Customer pays for a license to do so. Customer may not extend or create an additional trialperiod by re-installing the Software after the 30-day trial period.e. The Global Enterprise Edition of the Steel-Belted Radius software may be used by Customer only to manage access to Customer’s enterprise network.Specifically, service provider customers are expressly prohibited from using the Global Enterprise Edition of the Steel-Belted Radius software to support anycommercial network access services.The foregoing license is not transferable or assignable by Customer. No license is granted herein to any user who did not originally purchase the applicablelicense(s) for the Software from Juniper or an authorized Juniper reseller.4. Use Prohibitions. Notwithstanding the foregoing, the license provided herein does not permit the Customer to, and Customer agrees not to and shallnot: (a) modify, unbundle, reverse engineer, or create derivative works based on the Software; (b) make unauthorized copies of the Software (except asnecessary for backup purposes); (c) rent, sell, transfer, or grant any rights in and to any copy of the Software, in any form, to any third party; (d) removeany proprietary notices, labels, or marks on or in any copy of the Software or any product in which the Software is embedded; (e) distribute any copy ofthe Software to any third party, including as may be embedded in Juniper equipment sold in the secondhand market; (f) use any ‘locked’ or key-restrictedfeature, function, service, application, operation, or capability without first purchasing the applicable license(s) and obtaining a valid key from Juniper, evenif such feature, function, service, application, operation, or capability is enabled without a key; (g) distribute any key for the Software provided by Juniperto any third party; (h) use the Software in any manner that extends or is broader than the uses purchased by Customer from Juniper or an authorized Juniperreseller; (i) use Embedded Software on non-Juniper equipment; (j) use Embedded Software (or make it available for use) on Juniper equipment that theCustomer did not originally purchase from Juniper or an authorized Juniper reseller; (k) disclose the results of testing or benchmarking of the Software toany third party without the prior written consent of Juniper; or (l) use the Software in any manner other than as expressly provided herein.5. Audit. Customer shall maintain accurate records as necessary to verify compliance with this Agreement. Upon request by Juniper, Customer shall furnishsuch records to Juniper and certify its compliance with this Agreement.■iii

6. Confidentiality. The Parties agree that aspects of the Software and associated documentation are the confidential property of Juniper. As such, Customershall exercise all reasonable commercial efforts to maintain the Software and associated documentation in confidence, which at a minimum includesrestricting access to the Software to Customer employees and contractors having a need to use the Software for Customer’s internal business purposes.7. Ownership. Juniper and Juniper’s licensors, respectively, retain ownership of all right, title, and interest (including copyright) in and to the Software,associated documentation, and all copies of the Software. Nothing in this Agreement constitutes a transfer or conveyance of any right, title, or interest inthe Software or associated documentation, or a sale of the Software, associated documentation, or copies of the Software.8. Warranty, Limitation of Liability, Disclaimer of Warranty. The warranty applicable to the Software shall be as set forth in the warranty statement thataccompanies the Software (the “Warranty Statement”). Nothing in this Agreement shall give rise to any obligation to support the Software. Support servicesmay be purchased separately. Any such support shall be governed by a separate, written support services agreement. TO THE MAXIMUM EXTENT PERMITTEDBY LAW, JUNIPER SHALL NOT BE LIABLE FOR ANY LOST PROFITS, LOSS OF DATA, OR COSTS OR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES,OR FOR ANY SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THIS AGREEMENT, THE SOFTWARE, OR ANY JUNIPER ORJUNIPER-SUPPLIED SOFTWARE. IN NO EVENT SHALL JUNIPER BE LIABLE FOR DAMAGES ARISING FROM UNAUTHORIZED OR IMPROPER USE OF ANYJUNIPER OR JUNIPER-SUPPLIED SOFTWARE. EXCEPT AS EXPRESSLY PROVIDED IN THE WARRANTY STATEMENT TO THE EXTENT PERMITTED BY LAW,JUNIPER DISCLAIMS ANY AND ALL WARRANTIES IN AND TO THE SOFTWARE (WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE), INCLUDINGANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT. IN NO EVENT DOES JUNIPERWARRANT THAT THE SOFTWARE, OR ANY EQUIPMENT OR NETWORK RUNNING THE SOFTWARE, WILL OPERATE WITHOUT ERROR OR INTERRUPTION,OR WILL BE FREE OF VULNERABILITY TO INTRUSION OR ATTACK. In no event shall Juniper’s or its suppliers’ or licensors’ liability to Customer, whetherin contract, tort (including negligence), breach of warranty, or otherwise, exceed the price paid by Customer for the Software that gave rise to the claim, orif the Software is embedded in another Juniper product, the price paid by Customer for such other product. Customer acknowledges and agrees that Juniperhas set its prices and entered into this Agreement in reliance upon the disclaimers of warranty and the limitations of liability set forth herein, that the samereflect an allocation of risk between the Parties (including the risk that a contract remedy may fail of its essential purpose and cause consequential loss),and that the same form an essential basis of the bargain between the Parties.9. Termination. Any breach of this Agreement or failure by Customer to pay any applicable fees due shall result in automatic termination of the licensegranted herein. Upon such termination, Customer shall destroy or return to Juniper all copies of the Software and related documentation in Customer’spossession or control.10. Taxes. All license fees payable under this agreement are exclusive of tax. Customer shall be responsible for paying Taxes arising from the purchase ofthe license, or importation or use of the Software. If applicable, valid exemption documentation for each taxing jurisdiction shall be provided to Juniper priorto invoicing, and Customer shall promptly notify Juniper if their exemption is revoked or modified. All payments made by Customer shall be net of anyapplicable withholding tax. Customer will provide reasonable assistance to Juniper in connection with such withholding taxes by promptly: providing Juniperwith valid tax receipts and other required documentation showing Customer’s payment of any withholding taxes; completing appropriate applications thatwould reduce the amount of withholding tax to be paid; and notifying and assisting Juniper in any audit or tax proceeding related to transactions hereunder.Customer shall comply with all applicable tax laws and regulations, and Customer will promptly pay or reimburse Juniper for all costs and damages relatedto any liability incurred by Juniper as a result of Customer’s non-compliance or delay with its responsibilities herein. Customer’s obligations under thisSection shall survive termination or expiration of this Agreement.11. Export. Customer agrees to comply with all applicable export laws and restrictions and regulations of any United States and any applicable foreignagency or authority, and not to export or re-export the Software or any direct product thereof in violation of any such restrictions, laws or regulations, orwithout all necessary approvals. Customer shall be liable for any such violations. The version of the Software supplied to Customer may contain encryptionor other capabilities restricting Customer’s ability to export the Software without an export license.12. Commercial Computer Software. The Software is “commercial computer software” and is provided with restricted rights. Use, duplication, or disclosureby the United States government is subject to restrictions set forth in this Agreement and as provided in DFARS 227.7201 through 227.7202-4, FAR 12.212,FAR 27.405(b)(2), FAR 52.227-19, or FAR 52.227-14(ALT III) as applicable.13. Interface Information. To the extent required by applicable law, and at Customer's written request, Juniper shall provide Customer with the interfaceinformation needed to achieve interoperability between the Software and another independently created program, on payment of applicable fee, if any.Customer shall observe strict obligations of confidentiality with respect to such information and shall use such information in compliance with any applicableterms and conditions upon which Juniper makes such information available.14. Third Party Software. Any licensor of Juniper whose software is embedded in the Software and any supplier of Juniper whose products or technologyare embedded in (or services are accessed by) the Software shall be a third party beneficiary with respect to this Agreement, and such licensor or vendorshall have the right to enforce this Agreement in its own name as if it were Juniper. In addition, certain third party software may be provided with theSoftware and is subject to the accompanying license(s), if any, of its respective owner(s). To the extent portions of the Software are distributed under andsubject to open source licenses obligating Juniper to make the source code for such portions publicly available (such as the GNU General Public License(“GPL”) or the GNU Library General Public License (“LGPL”)), Juniper will make such source code portions (including Juniper modifications, as appropriate)available upon request for a period of up to three years from the date of distribution. Such request can be made in writing to Juniper Networks, Inc., 1194N. Mathilda Ave., Sunnyvale, CA 94089, ATTN: General Counsel. You may obtain a copy of the GPL at http://www.gnu.org/licenses/gpl.html, anda copy of the LGPL at http://www.gnu.org/licenses/lgpl.html.15. Miscellaneous. This Agreement shall be governed by the laws of the State of California without reference to its conflicts of laws principles. The provisionsof the U.N. Convention for the International Sale of Goods shall not apply to this Agreement. For any disputes arising under this Agreement, the Partieshereby consent to the personal and exclusive jurisdiction of, and venue in, the state and federal courts within Santa Clara County, California. This Agreementconstitutes the entire and sole agreement between Juniper and the Customer with respect to the Software, and supersedes all prior and contemporaneousiv ■

agreements relating to the Software, whether oral or written (including any inconsistent terms contained in a purchase order), except that the terms of aseparate written agreement executed by an authorized Juniper representative and Customer shall govern to the extent such terms are inconsistent or conflictwith terms contained herein. No modification to this Agreement nor any waiver of any rights hereunder shall be effective unless expressly assented to inwriting by the party to be charged. If any portion of this Agreement is held invalid, the Parties agree that such invalidity shall not affect the validity of theremainder of this Agreement. This Agreement and associated documentation has been written in the English language, and the Parties agree that the Englishversion will govern. (For Canada: Les parties aux présentés confirment leur volonté que cette convention de même que tous les documents y compris toutavis qui s'y rattaché, soient redigés en langue anglaise. (Translation: The parties confirm that this Agreement and all related documentation is and will bein the English language)).■v

vi ■

Table of ContentsPart 1 Security Products Safety OverviewChapter 1 Safety Recommendations and Warnings 3Definitions of Safety Warning Levels ...............................................................3Safety Recommendations and Warnings .........................................................4Safety Warnings ..............................................................................................5Installation ................................................................................................5Power Disconnection ................................................................................5Disconnecting Power from the Device ................................................5User-Serviceable Parts ..............................................................................5Circuit Breaker—Maximum Voltage ..........................................................6SELV Circuit ..............................................................................................6Lightning Activity ......................................................................................6Lithium Battery .........................................................................................6Handling the Battery ..........................................................................6Chapter 2 General Site and Installation Requirements 7Onsite Precautions ..........................................................................................8Qualified Personnel Warning ...........................................................................8Restricted Access Area Warning ......................................................................8Installation Instructions Warning .....................................................................8Rack-Mounting Requirements and Warnings ...................................................9Fire Safety Requirements ................................................................................9Fire Suppression and Fire Suppression Equipment .................................10Chapter 3 Power Considerations and Electrical Safety Guidelines andWarnings 11Power Considerations ...................................................................................11IT Power Statement ................................................................................11Power Cable Warning (Japanese) ............................................................11Warning Statement for Norway and Sweden ..........................................12For Devices That Support AC Power .......................................................12For Devices That Support DC Power .......................................................12Table of Contents ■vii

DC Power Wiring Sequence Warning ......................................................13Redundant Power Considerations ...........................................................13In Case of Electrical Accident ........................................................................13General Electrical Safety Guidelines and Warnings ..................................14Chapter 4 Handling Devices 15Preventing Electrostatic Discharge Damage ..................................................15General Laser Safety Guidelines .....................................................................16Class 1 Laser Product Warning ...............................................................17Class 1 LED Product Warning .................................................................17Laser Beam Warning ..............................................................................17Radiation from Open Port Apertures Warning ........................................17Telecommunication Line Cord Warning ........................................................17Preventing Electromagnetic Interference .......................................................18Covering Empty Slots ....................................................................................18Jewelry Removal ...........................................................................................18Operating Temperature Warning ..................................................................18Chapter 5 Agency Approvals and Compliance Statements 19Agency Approvals ..........................................................................................19Compliance Statements .................................................................................20Industry Canada Statement .....................................................................20Federal Communications Commission Interference Statement ...............20Taiwan DGT ............................................................................................21VCCI Compliance ....................................................................................21Wireless Connections for Products with Wireless Interfaces ...................22Product Reclamation and Recycling Program .........................................22Compliance Statement for Environmental Requirements .......................23Lithium Battery ................................................................................23Compliance Statements for Acoustic Noise (Germany) ............................23Part 2 IndexIndex .............................................................................................................27viii ■Table of ContentsJuniper Networks Security Products Safety Guide

Part 1Security Products Safety Overview■Safety Recommendations and Warnings on page 3■General Site and Installation Requirements on page 7■Power Considerations and Electrical Safety Guidelines and Warnings on page 11■Handling Devices on page 15■Agency Approvals and Compliance Statements on page 19Security Products Safety Overview ■1

2■Security Products Safety OverviewJuniper Networks Security Products Safety Guide

Chapter 1Safety Recommendations and WarningsThis guide contains general safety recommendations and warnings about avoidingsituations that could cause injury to people or devices. For specific guidelines aboutinstalling or using a device, see the hardware guide for your device.NOTE: For translated versions of this guide, see the Documentation CD shipped withyour device or the Juniper Networks Technical Documentation Web site atwww.juniper.net/techpubs.This section includes the following topics:■Definitions of Safety Warning Levels on page 3■Safety Recommendations and Warnings on page 4■Safety Warnings on page 5Definitions of Safety Warning LevelsThis guide uses the following three levels of safety warnings:NOTE: You might find this information helpful in a particular situation or mightotherwise overlook it.CAUTION: You need to observe the specified guidelines to avoid minor injury ordiscomfort to you or severe damage to the device.WARNING: This symbol means danger. You are in a situation that could cause bodilyinjury. Before you work on any equipment, be aware of the hazards involved withelectrical circuitry and be familiar with standard practices for preventing accidents.Definitions of Safety Warning Levels ■3

Safety Recommendations and WarningsBefore working on any equipment, be aware of the hazards involved with electricalcircuitry and be familiar with standard practices for preventing accidents. Observethese important guidelines when installing or manipulating a Juniper Networks device:■Always disconnect all power supply connections before:■Removing a chassis■Changing a fuse■Locate the emergency power-off switch for the area where you are working.■Allow adequate air circulation. Do not stack devices or balance any devices orequipment over other devices or equipment. If the device is installed in a rack,the rack must be secured to the building structure. The device should be mountedat the bottom of the rack if it is the only unit in the rack.■Look carefully for possible hazards in the work area, such as moist floors,ungrounded power extension cables, and missing safety grounds.■Do not perform any action that creates a potential hazard to people or makesthe equipment unsafe.■Do not work alone if potentially hazardous conditions exist.■Keep the area around the chassis clear and free from dust before, during, andafter installation.■Do not wear loose clothing or jewelry, such as rings, bracelets, or chains, whichcould become caught in the chassis.■Wear safety glasses if you are working under any conditions that could behazardous to your eyes.■Never attempt to lift an object that is too heavy for one person to handle.■Never install or manipulate wiring during electrical storms.■Replace fuses only with fuses of the same type and rating.■Do not open or remove chassis covers or sheet-metal parts unless instructionsfor doing so are provided in the hardware guide for this device. Such an actioncould cause severe electrical shock.■Do not push or force any objects through any opening in the chassis frame. Suchan action could result in electrical shock or fire.■Avoid spilling liquid onto the chassis. Such an action could cause electrical shockor damage the chassis.■Avoid touching uninsulated electrical wires or terminals that have not beendisconnected from their power source. Such an action could cause electricalshock.■Always ensure that all modules, power supplies, and blank panels are fullyinserted and that the installation screws are fully tightened.4■Safety Recommendations and WarningsJuniper Networks Security Products Safety Guide

Safety WarningsFor your protection, and the protection of people around you, ensure that you adhereto the following set of safety warnings.InstallationWARNING: Read the cabling instructions before you connect the device to its powersource. See the hardware guide for your device.Power DisconnectionWARNING: Before working on a device that has a switch, switch the circuit to theOFF position and disconnect the power cord to all power supplies.For DC power supplies, locate the circuit breaker on the panel board that servicesthe DC circuit, switch the circuit breaker to the OFF position, and tape the switchhandle of the DC circuit breaker to secure it in the OFF position.Disconnecting Power from the DeviceWARNING: Some devices have more than one power supply connection. Allconnections must be removed completely to shut off power from the unit.User-Serviceable PartsWARNING: The chassis of some devices are tamperproof. Do not open the chassisof a tamper-proof device under any circumstances. Doing so will void the warranty.Other devices have user-serviceable parts such as fuses, memory modules, processormodules, and application modules, which require the chassis to be opened. You canreplace these components when necessary. Make sure to return the components tothe manufacturer for service or replacement. For more information aboutuser-serviceable parts, see the hardware guide for your device.Safety Warnings ■5Chapter 1: Safety Recommendations and Warnings

Circuit Breaker—Maximum VoltageWARNING: The device relies on the building’s safety features for protection againstshort-circuit, over-current, and earth (grounding) fault. Ensure that the building’ssafety features are properly rated for the device. Depending on which type ofpower—AC or DC—the device uses, the phase conductor (or all current-carryingconductors) should use a fuse or breaker that has the maximum voltage specifiedfor the device. See the hardware guide for your device.SELV CircuitJuniper Networks devices support Ethernet 10BaseT, 100BaseT, 1000BaseT, serial,console, and auxiliary ports, which contain safety extra-low voltage (SELV) circuits.To find out which cable to use with which interface, see the hardware guide for yourdevice.CAUTION: Do not connect the Ethernet 10BaseT, 100BaseT, or 1000BaseT ports toa telephone line or any Telco line (for example, T-1, T-3, or RJ-48 lines).Lightning ActivityWARNING: Do not work on the device, or connect or disconnect the device, duringlightning activity.Lithium BatteryWARNING: Return the device to the manufacturer for battery replacement. Moreover,a tamperproof chassis should not be opened under any circumstances. Doing so willalso void the warranty.Handling the BatteryWARNING: Replacing the battery incorrectly might result in an explosion. Replacethe battery only with the same or equivalent type recommended by the manufacturer.Dispose of used batteries according to the manufacturer's instructions.6■Safety WarningsJuniper Networks Security Products Safety Guide

Chapter 2General Site and InstallationRequirementsCAUTION: For the safe installation and operation of your device, ensure that yoursite is properly prepared before beginning the hardware installation.The following information will help you ensure that the site is properly prepared:■Check the power at your site to ensure that you are receiving clean power (freeof spikes and noise). Install a power conditioner if necessary.■Choose a site that maintains an ambient temperature of 32 to 104°F (0 to 40°C).The device is intended for use in a normal office environment. For more extremeconditions, verify that temperature, humidity, and power conditions meet thespecifications for each Juniper Networks device. For specifications, see thehardware guide for your device.■The device relies on the building’s safety features for protection againstshort-circuit, over-current, and earth (grounding) fault. Ensure that the building’ssafety features are properly rated for the device.■Ensure that the device is installed in a secure location where access to the deviceis limited to authorized personnel.Observe the following guidelines and warnings before and during device installation:■Onsite Precautions on page 8■Qualified Personnel Warning on page 8■Restricted Access Area Warning on page 8■Installation Instructions Warning on page 8■Rack-Mounting Requirements and Warnings on page 9■Fire Safety Requirements on page 9■7

Onsite PrecautionsNOTE: You can place the device on a desktop, on a wall or mounted in a rack. Thelocation of the chassis and the layout of your equipment rack or wiring room areextremely important for proper system operation. Equipment placed too closetogether will cause inadequate ventilation, as well as render areas of the deviceinaccessible for system maintenance during any system malfunctions and shutdowns.When planning your site layout and equipment locations, follow these precautionsdescribed below to help avoid equipment failures and reduce the possibility ofenvironmentally caused shutdowns. If you are experiencing shutdowns or unusuallyhigh errors with your existing equipment, these precautions may help you isolatethe cause of the failures and prevent future problems.■Ensure that the room in which you operate your system has adequate aircirculation. Electrical equipment generates heat. Natural air temperature mightnot be sufficient to cool the equipment to acceptable operating temperatureswithout an additional ventilation system.■Choose a site with a dry, clean, well-ventilated and air-conditioned area.Qualified Personnel WarningWARNING: Only trained and qualified personnel should install or replace the device.Restricted Access Area WarningWARNING: The device is intended for installation in restricted access areas. Arestricted access area is an area to which access can be gained only by servicepersonnel through the use of a special tool, lock and key, or other means of security,and which is controlled by the authority responsible for the location.Installation Instructions WarningWARNING: Read the installation instructions before you connect the device to apower source.8■Onsite PrecautionsJuniper Networks Security Products Safety Guide

Rack-Mounting Requirements and WarningsThe following information will help you plan an acceptable equipment-rackconfiguration.WARNING: To prevent bodily injury when mounting or servicing the device in a rack,take the following precautions to ensure that the system remains stable. The followingdirectives help maintain your safety:■Ensure that the equipment rack into which the device is installed is evenly andsecurely supported to avoid the hazardous condition that could result from unevenmechanical loading.■If the device is installed in a rack, the rack must be secured to the buildingstructure.■The device should be mounted at the bottom of the rack if it is the only unit inthe rack.■When mounting the device in a partially filled rack, load the rack from the bottomto the top with the heaviest component at the bottom of the rack.■If the rack is provided with stabilizing devices, install the stabilizers beforemounting or servicing the device in the rack.■Do not stack devices or balance any devices or equipment over other devices orequipment.■Install the device in an open rack whenever possible. If you install the device inan enclosed rack, ensure that the device has adequate ventilation and that therack allows adequate clearance for both airflow and maintenance. Ensure thatthe rack is not overly congested because each unit generates heat. An enclosedrack should have louvered sides and a fan to provide cooling air.■When mounting a chassis in an open rack, ensure that the rack frame does notblock the intake or exhaust ports. If the chassis is installed on slides, check theposition of the chassis when it is seated all the way into the rack.■In an enclosed rack with a ventilation fan in the top, excessive heat generatedby equipment near the bottom of the rack can be drawn upward and into theintake ports of the equipment above it in the rack. Provide adequate ventilationfor equipment at the bottom of the rack.■Baffles can help to isolate exhaust air from intake air, which also helps to drawcooling air through the chassis. The best placement of the baffles depends onthe airflow patterns in the rack, which can be found by experimenting withdifferent arrangements.Fire Safety RequirementsIn the event of a fire emergency involving devices and other network equipment,the safety of people is the primary concern. Establish procedures for protectingRack-Mounting Requirements and Warnings ■9Chapter 2: General Site and Installation Requirements

people in the event of a fire emergency, provide safety training, and properly provisionfirecontrol equipment and fire extinguishers.In addition, establish procedures to protect your equipment in the event of a fireemergency. Juniper Networks devices should be installed in an environment suitablefor electronic equipment. We recommend that fire suppression equipment be availablein the event of a fire in the vicinity of the equipment, and that all local fire, safety,and electrical codes and ordinances be observed when installing and operating yourequipment.Fire Suppression and Fire Suppression EquipmentIn the event of an electrical hazard or fire, first turn off power to the equipment atthe source. Then use a Type C fire extinguisher to extinguish the fire. Type C fireextinguishers use noncorrosive fire retardants such as carbon dioxide (CO2) andHalotron™ and are most effective for suppressing electrical fires. Type C fireextinguishers displace the oxygen from the point of combustion to eliminate the fire.For extinguishing fire on or around equipment that draws air from the environmentfor cooling, use this type of inert oxygen displacement extinguisher instead of anextinguisher that leave residues on equipment.Do not use multipurpose Type ABC chemical fire extinguishers (dry chemical fireextinguishers) near Juniper Networks equipment. The primary ingredient in thesefire extinguishers is monoammonium phosphate, which is very sticky and difficultto clean. In addition, in minute amounts of moisture, monoammonium phosphatecan become highly corrosive and corrodes most metals.Any equipment in a room in which a chemical fire extinguisher has been dischargedis subject to premature failure and unreliable operation. The equipment is consideredto be irreparably damaged.NOTE: To keep warranties effective, do not use a dry chemical fire extinguisher tocontrol a fire at or near a Juniper Networks device. If a dry chemical fire extinguisheris used, the unit is no longer eligible for coverage under a service agreement.We recommend that you dispose of any irreparably damaged equipment in anenvironmentally responsible manner.10 ■Fire Safety RequirementsJuniper Networks Security Products Safety Guide

Chapter 3Power Considerations and ElectricalSafety Guidelines and WarningsThis section includes the following topics:■Power Considerations on page 11■In Case of Electrical Accident on page 13Power ConsiderationsAC and DC power supplies, and an optional redundant power supply, are availablefor some devices.CAUTION: Do not overload the wiring; be careful when connecting devices to thesupply circuit.NOTE: See your hardware guide for AC and DC power specifications and cablinginformation and for redundant power-supply availability.WARNING: Use only power cord sets that are certified by the local authorities tomeet local regulations and building codes.IT Power StatementWARNING: The device is designed to work with IT power systems.Power Cable Warning (Japanese)WARNING:Power Considerations ■11

Translation:Warning: The attached power cable is only for this product. Do not use the cable foranother product.Warning Statement for Norway and SwedenWARNING: The equipment must be connected to an earthed mains socket-outlet.Advarsel Apparatet skal kobles til en jordet stikkontakt.varning! Apparaten skall anslutas till jordat nätuttag.For Devices That Support AC PowerWARNING: Juniper Networks devices are designed for connection to IT powersystems. A IT power system is a power distribution system with one point connectedto earth through an impedance. The exposed conductive parts of the installation areconnected to protective ground conductors.Ensure that the plug-socket combination is accessible at all times, because it servesas the main disconnecting device.Ensure that the device is connected to an AC power source equipped with a surgeprotection device.For Devices That Support DC PowerWARNING: Connect DC-input power supplies only to a DC power source that complieswith the safety extra-low voltage (SELV) requirements in the UL 60950-1, CSA60950-1, EN 60950-1, and IEC 60950-1 standards.Incorporate a freely accessible two-poled disconnect device in the fixed wiring.12 ■Power ConsiderationsJuniper Networks Security Products Safety Guide

Ensure that there is no power in the DC circuits before installing or removing powersupplies. As a precautionary measure, you can tape the switch handle of the DCcircuit breaker to secure it in the OFF position.Use only copper conductors to connect to a DC terminal block.When stranded wiring is required, use approved wiring terminations such asclosed-loop or spade-type lugs. These terminations should be the appropriate sizefor the wires and should clamp both the insulation and the conductor.Ensure that no exposed portion of the DC-input power source wire extends from theterminal block plug. An exposed wire can conduct a harmful level of electricity. Ifyou remove the cover on the DC terminal block for any reason, make sure that youreplace the cover when you are done.DC Power Wiring Sequence WarningWARNING: Wire the DC power supply using the appropriate lungs. When connectingthe power, the proper wiring sequence is ground to ground, +RTN to +RTN, then– 48V to – 48V. While disconnecting power, the proper wiring sequence is – 48V to–48V, +RTN to +RTN, then ground to ground. Note that the ground wire shouldalways be connected first and disconnected last.Redundant Power ConsiderationsIf your device includes an optional redundant power supply, connect each of the twopower supplies to different input power sources. Failure to do so makes the devicesusceptible to total power failure in the event that one of the power supplies fails.WARNING: If you need to disconnect the device to perform servicing, disconnectboth power supplies. Otherwise, system components such as plug-in Input/OutputCards (IOCs) could be damaged.In Case of Electrical AccidentIf an electrical accident results in an injury, take the following actions in this order:1. Use caution. Be aware of potentially hazardous conditions that could cause furtherinjury.2. Disconnect power from the device.3. If possible, send another person to get medical aid. Otherwise, assess thecondition of the victim, then call for help.In Case of Electrical Accident ■13Chapter 3: Power Considerations and Electrical Safety Guidelines and Warnings

General Electrical Safety Guidelines and WarningsObserve the following guidelines when working on a device powered by electricity:■Locate the emergency power-off switch for the room in which you are workingso that if an electrical accident occurs, you can quickly turn off the power.■Do not work alone if potentially hazardous conditions exist anywhere in yourworkspace.■Never assume that power is disconnected from a circuit. Always check the circuitbefore starting to work.■Carefully look for possible hazards in your work area, such as moist floors,ungrounded power extension cords, and missing safety grounds.■Operate the device within marked electrical ratings and follow product usageinstructions.■For the device and peripheral equipment to function safely and correctly, usethe cables and connectors specified for the attached peripheral equipment, andmake certain they are in good condition.Install the device in compliance with the following local, national, or internationalelectrical codes:■Compliance Statementfor Electrical Codes■United States—National Fire Protection Association (NFPA 70), United StatesNational Electrical Code■Canada—Canadian Electrical Code, Part 1, CSA C22.1■Other countries—International Electromechanical Commission (IEC) 60364, Part1 through Part 7■Evaluated to the IT power system14 ■In Case of Electrical AccidentJuniper Networks Security Products Safety Guide

Chapter 4Handling DevicesThis section includes the following topics:■Preventing Electrostatic Discharge Damage on page 15■General Laser Safety Guidelines on page 16■Telecommunication Line Cord Warning on page 17■Preventing Electromagnetic Interference on page 18■Covering Empty Slots on page 18■Jewelry Removal on page 18■Operating Temperature Warning on page 18Preventing Electrostatic Discharge DamageElectrostatic discharge (ESD) damage occurs when electronic cards or componentsare mishandled and can result in complete or intermittent failures.Many devices are sensitive to damage from static electricity. Some components canbe impaired by voltages as low as 30 V. You can easily generate potentially damagingstatic voltages whenever you handle plastic or foam packing material or if you movecomponents across plastic or carpets. Observe the following guidelines to minimizethe potential for electrostatic discharge damage, which can cause intermittent orcomplete component failures:■Always use an ESD-preventive wrist strap or ankle strap when handling electroniccomponents, and verify that it is in direct contact with your skin.CAUTION: For safety, periodically check the resistance value of the ESD strap. Themeasurement should be in the range of 1 to 10 Mohms.■When handling any component that is removed from the chassis, verify that theequipment end of your ESD strap is attached to one of the ESD points on thechassis. See the hardware guide for your device.■Avoid contact between the component and your clothing. The wrist strap onlyprotects the card from ESD voltages on the body; ESD voltages emitted fromclothing can still damage components.Preventing Electrostatic Discharge Damage ■15

■Always handle cards by the faceplates and edges only; avoid touching the printedcircuit board and connector pins.■When removing or installing a component, always place it component-side upon an antistatic surface, in an antistatic card rack, or in an electrostatic bag (seeFigure 1 on page 16). If you are returning a component, place it in an electrostaticbag before packing it.Figure 1: Placing a Component in to an Electrostatic BagGeneral Laser Safety GuidelinesSome Juniper Networks devices are equipped with fiber-optic ports, which emitradiation that may be harmful to the human eye. Be aware of the following.Fiber-optic ports (for example, GBIC and mini-GBIC) are considered Class 1 laser orClass 1 LED ports.When working around PICs, observe the following safety guidelines to prevent eyeinjury:■Do not look into unterminated ports or at fibers that connect to unknown sources.■Do not examine unterminated optical ports with optical instruments.■Avoid direct exposure to the beam.WARNING: Unterminated optical connectors can emit invisible laser radiation. Thelens in the human eye focuses all the laser power on the retina, so focusing the eyedirectly on a laser source—even a low-power laser—could permanently damage theeye.16 ■General Laser Safety GuidelinesJuniper Networks Security Products Safety Guide

Class 1 Laser Product WarningWARNING: Class 1 Laser product.Class 1 LED Product WarningWARNING: Class 1 LED Product.Laser Beam WarningWARNING: Do not stare into the laser beam or view it directly with opticalinstruments.Invisible radiation might be emitted from the aperture of the port when no fibercable is connected.These products have been tested and found to comply with Class 1 limits of IEC60825-1, EN 60825-1, and 21CFR1040.Radiation from Open Port Apertures WarningWARNING: Because invisible radiation may be emitted from the aperture of the portwhen no fiber cable is connected, avoid exposure to radiation and do not stare intoopen apertures.Telecommunication Line Cord WarningWARNING: To reduce the risk of fire, use only No. 26 AWG or larger UL-listed orCSA-certified telecommunication line cord.Telecommunication Line Cord Warning ■17Chapter 4: Handling Devices

Preventing Electromagnetic InterferenceNOTE: When you run wires for any significant distance in an electromagnetic field,electromagnetic interference (EMI) can occur between the field and the signals onthe wires. Note the following information:■Bad plant wiring can result in radio frequency interference (RFI).■Strong EMI, especially when it is caused by lightning or radio transmitters, candestroy the signal drivers and receivers in the system and can even create anelectrical hazard by conducting power surges through lines and into the system.To prevent and remedy strong EMI, consult RFI experts.Covering Empty SlotsEnsure that all cards, faceplates, and covers are in place. Blank faceplates and coverpanels are used for the following reasons:■Preventing exposure to hazardous voltages and currents inside the chassis■Helping contain electromagnetic interference (EMI) that might disrupt otherequipment■Directing the flow of cooling air through the chassisJewelry RemovalWARNING: Before working on equipment that is connected to power lines, removejewelry, including rings, necklaces, and watches. Metal objects heat up whenconnected to power and ground and can cause serious burns or weld the metal objectto the terminals.Operating Temperature WarningWARNING: To prevent the device from overheating, do not operate it in an area thatexceeds the maximum recommended ambient temperature of 104°F (40°C). Toprevent airflow restriction, allow at least 6 in. (15.2 cm) of clearance around theventilation openings.18 ■Preventing Electromagnetic InterferenceJuniper Networks Security Products Safety Guide

Chapter 5Agency Approvals and ComplianceStatementsThis section includes the following topics:■Agency Approvals on page 19■Compliance Statements on page 20Agency ApprovalsThe security device complies with the following standards (for specific version of thestandard relevance to the product, please refer to individual product manual) :■Safety■CSA 60950-1 Safety of Information Technology Equipment■UL 60950-1 Safety of Information Technology Equipment■EN 60950-1 Safety of Information Technology Equipment■IEC 60950-1 Safety of Information Technology Equipment (with countrydeviations)■EN 60825-1 Safety of Laser Products - Part 1: Equipment Classification■EMC■EN 300 386 Telecom Network Equipment - EMC requirements■EMI■FCC Part 15 USA Radiated Emissions■EN 55022 European Radiated Emissions■VCCI Japanese Radiated Emissions■Immunity■EN 55024 Information Technology Equipment Immunity Characteristics■EN-61000-3-2 Power Line Harmonics■EN-61000-3-3 Power Line Voltage Fluctuations■EN-61000-4-2 Electrostatic DischargeAgency Approvals ■19

■EN-61000-4-3 Radiated Immunity■EN-61000-4-4 Electrical Fast Transients■EN-61000-4-5 Surge■EN-61000-4-6 Immunity to Conducted Disturbances■EN-61000-4-11 (2004) Voltage Dips and SagsCompliance StatementsIndustry Canada StatementThe following is applicable to devices with wireless interfaces:Operation is subject to the following two conditions:1. This device may not cause interference, and2. This device must accept any interference, including interference that may causeundesired operation of the device.This device has been designed to operate with an antenna having a maximum gainof 4 dB. Antenna having a higher gain is strictly prohibited per regulations of IndustryCanada. The required antenna impedance is 50 ohms.To reduce potential radio interference to other users, the antenna type and its gainshould be so chosen that the EIRP is not more than required for successfulcommunication.To prevent radio interference to the licensed service, this device is intended to beoperated indoors and away from windows to provide maximum shielding.Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.Federal Communications Commission Interference StatementThe following is applicable to devices with wireless interfaces:This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one of thefollowing measures:20 ■Compliance StatementsJuniper Networks Security Products Safety Guide5

■Reorient or relocate the receiving antenna.■Increase the separation between the equipment and receiver.■Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.■Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and(2) this device must accept any interference received, including interference thatmay cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority to operate this equipment.IMPORTANT NOTE:FCC Radiation Exposure Statement: This equipment complies with FCC radiationexposure limits set forth for an uncontrolled environment. This equipment shouldbe installed and operated with minimum distance 20cm between the radiator & yourbody.This transmitter must not be co-located or operating in conjunction with any otherantenna or transmitter.Taiwan DGTThe following is applicable to devices with wireless interfaces:VCCI ComplianceThe following VCCI compliance information applies to security products that meetVCCI Class A or Class B limits. See the specifications section in the hardware guidefor your device to determine whether the product meets Class A or Class B limits.Compliance Statements ■21Chapter 5: Agency Approvals and Compliance Statements

Translation:This is a Class A product. In a domestic environment this product may cause radiointerference in which case the user may be required to take adequate measures.Translation:This is a Class B product based on the standard of the Voluntary Control Council forInterference by Information Technology Equipment (VCCI). If this product is usednear a radio or television receiver in a domestic environment, it may cause radiointerference. Install and use the equipment according to the instruction manual.Wireless Connections for Products with Wireless InterfacesWARNING: In countries other than the United States or Japan, you must set thecorrect country code with the set wlan country-code command to avoid violating localradio spectrum laws. This command sets the selectable channel range and transmitpower level so that a WLAN connection can be established. For more informationabout country codes, see the hardware guide for your device.Product Reclamation and Recycling ProgramJuniper Networks is committed to environmentally responsible behavior. As part ofthis commitment, we work to comply with environmental standards such as theEuropean Union’s Waste Electrical and Electronic Equipment (WEEE) Directive andRestriction of Hazardous Substances (RoHS) Directive.These directives and other similar regulations from countries outside the EuropeanUnion regulate electronic waste management and the reduction or elimination ofspecific hazardous materials in electronic products. The WEEE Directive requireselectrical and electronics manufacturers to provide mechanisms for the recyclingand reuse of their products. The RoHS Directive restricts the use of certain substancesthat are commonly found in electronic products today. Restricted substances includeheavy metals, including lead, and poly-brominated materials. The RoHS Directive,with some exemptions, applies to all electrical and electronic equipment.22 ■Compliance StatementsJuniper Networks Security Products Safety Guide

In accordance with Article 11(2) of Directive 2002/96/EC (WEEE), products put onthe market after 13 August 2005 are marked with the following symbol or includeit in their product documentation: a cross-out wheeled waste bin with a bar beneath.Juniper Networks provides recycling support for our equipment worldwide to complywith the WEEE Directive. For recycling information, send e-mail torecycling@juniper.net indicating the type of Juniper Networks equipment that youwish to dispose of and the country where it is currently located, or contact yourJuniper Networks account representative.Products returned through our reclamation process are recycled, recovered, ordisposed of in a responsible manner. Our packaging is designed to be recycled andshould be handled in accordance with your local recycling policies.Compliance Statement for Environmental RequirementsThis section describes the Compliance Statements for Environmental Requirements:Lithium BatteryBatteries in this product are not based on mercury, lead, or cadmium substances.The batteries used in this product are in compliance with EU Directives 91/157/EEC,93/86/EEC, and 98/101/EEC. The product documentation includes instructionalinformation about the proper method of reclamation and recycling.Compliance Statements for Acoustic Noise (Germany)Maschinenlärminformations-Verordnung - 3. GPSGV, der höchste Schalldruckpegelbeträgt 70_dB(A)oder weniger gemäss EN ISO 7779.Translation:The maximum emitted sound pressure level is 70_dB(A) or less per EN ISO 7779.Compliance Statements ■23Chapter 5: Agency Approvals and Compliance Statements

24 ■Compliance StatementsJuniper Networks Security Products Safety Guide Federal Communications Commission Interference Statement Country Code Statement For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in indoor environment only. Industry Canada Statement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems. The maximum antenna gain permitted (for devices in the band 5725-5825 MHz) to comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate, as stated in section A9.2(3). IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Part 2Index■Index on page 27Index ■25

26 ■IndexJuniper Networks Security Products Safety Guide

IndexAagency approvals.........................................................19antistatic mat, using.....................................................16Ccompliance, general standards.....................................19Eelectromagnetic interferencepreventing............................................................18standards..............................................................19electrostaticbag using to store components.............................15electrostatic dischargepreventing damage from......................................15wrist strap or ankle strap......................................15EMC standards.............................................................19EMI standards..............................................................19ESDpreventing damage from......................................15wrist strap or ankle strap......................................15Ethernet port connection...............................................6Ffire safety specifications.................................................9Iimmunity standards.....................................................19Pports, Ethernet...............................................................6power............................................................................7Rrack................................................................................8rack configuration..........................................................9racks..............................................................................9SSELV..............................................................................6site requirements...........................................................7specifications, fire safety................................................9standards compliance..................................................19Vventilation..................................................................8, 9Index ■27

28 ■IndexJuniper Networks Security Products Safety Guide

Navigation menu