Juniper Networks WLA321 WLA321 Wireles LAN Access Point User Manual WLA321 and WLA322 QSG
Juniper Networks, Inc. WLA321 Wireles LAN Access Point WLA321 and WLA322 QSG
Manual
WLA321 and WLA322 Access Points Quick Start See the complete Wireless LAN Services (WLS) product documentation at http://www.juniper.net/techpubs/. The Juniper Networks WLA321 Wireless LAN Access Point is an indoor, dual-band access point with one 2.4GHz/5GHz 2x2 IEEE 802.11n radio and two internal antennas. The Juniper Networks WLA322 Wireless LAN Access Point is an indoor, dual-band access point with two radios (one 5GHz 2x2 IEEE 802.11n enhanced power radio and one standard power 2.4GHz radio) and four internal antennas. 4. Ensure the snaps on the top of the ceiling-mount bracket are open so that the clips can fully extend to fit around the ceiling rail. The bracket is shipped in an open position so that it is ready to be clipped over a ceiling rail. Ceiling Installation for WLA321 and WLA322 Access Points Install WLA321 and WLA322 access points on the ceiling using the mounting bracket provided with the kit or on a junction box on the wall. The primary installation method for WLA321 and WLA322s is the ceiling mount. For instructions for purchasing a junction box wall-mount kit and for installing the access point on the junction box see the WLS documentation at http://www.juniper.net/techpubs/. 5. If the bracket is closed, open the snaps by pressing in and up with your thumbs on both sides of the snaps on the bottom of the bracket until it is fully open. WLA321 and WLA322 Access Point Package To install and connect the access point, you need: One ceiling-mount bracket (provided) Mounting template (provided) Category 5 straight-through signaling cable with RJ-45 connectors; installed (not provided) Box cutter or similar tool to cut ceiling tile (not provided) (Optional) Security kit, which includes a security tool and a security screw (The kit is not provided and can be ordered separately.) Part 1: Install the Access Point sh Pu in These instructions describe installing the access point on a 9/16-inch or 15/16-inch T ceiling-tile rail. 1. Select an installation location under a recessed rail in the ceiling. 2. Cut a hole as follows in the ceiling tile for the Category 5 cable: − Place the mounting template over the area where you will install the access point. − Use the box cutter or similar tool to cut along the line marking the opening for the port connectors. − Remove the mounting template and the material you cut from the ceiling tile. 6. With the bracket clips fully extended, align the clips with the rail and hook the clips around the top sides of the rail. Push in on the sides of the bracket until the clips lock over the rail. Listen for a click that indicates that the clips have locked. Be sure the bracket has locked securely onto the rail by gently pulling down on the bracket before installing the access point. Push in 3. Run the Category 5 cable from the ceiling through the hole in the ceiling tile. 7. Grasp the Category 5 cable that extends from the ceiling and plug it into the access point. 8. Align the access point with the bracket and press forward until the access point clicks into place. Be sure the access point is seated correctly in the bracket by gently pulling down on the access point. Part 2: Connect the Access Point to a Wireless LAN Controller After you install the access point, you can connect the access point directly or indirectly to a wireless LAN controller (WLC) through an intermediate Layer 2 or Layer 3 network device. To connect the access point directly to a WLC: 1. Insert one end of the installed Category 5 cable into the Ethernet port of the access point and the other end into the Ethernet port of the controller. 2. Look at the access point LED for the port on the controller and verify that the link is activated. The link is activated if the LED is green and glowing steadily. Part 3: Configure the Access Point Connection 9. If the access point is not properly secured, press the release button on top of the bracket to unlock the access point. Realign the access point, making sure the cable is still connected, and push in on the access point until it clicks securely into place. Release NOTE: We recommend that you use the optional security kit to secure the access point. The kit includes a security tool and a security screw. Be sure to retain the tool so you can unlock and move the access point. Never use a power tool to insert or remove the security screw. 10. (Optional) To lock the access point into place, secure the security screw in the release button by using the tool provided with the security kit. Do not overtighten the screw. NOTE: If you are installing the access point in a wireless LAN mesh or wireless bridge configuration, you must configure the access point before deploying the access point in the final location. For more information, see the Mobility System Software Configuration Guide at http://www.juniper.net/techpubs/. To configure the access point connection, use the RingMaster GUI or the Mobility System Software CLI. Safety Warnings Summary This is a summary of safety warnings. For a complete list of warnings, including translations, see the Juniper Networks Regulatory Guide in the WLS documentation at http://www.juniper.net/techpubs/. WARNING: Failure to observe these safety warnings can result in personal injury or death. System administrators and equipment installers of the WLAN system are responsible for the system’s proper setup and operation in accordance with all rules and regulations of the country in which the equipment operates. Perform only the procedures described in this quick start and the Wireless LAN Services (WLS) documentation. Before installing the WLC, read the planning instructions in the Wireless LAN Services (WLS) documentation to make sure that the site meets power, environmental, and clearance requirements for the switch. Contacting Juniper Networks For technical support, see http://www.juniper.net/support/requesting-support.html. Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are trademarks of Juniper Networks, Inc. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify, transfer, or otherwise revise this publication without notice. Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785. Copyright © 2012 Juniper Networks, Inc. All rights reserved. Part Number: 530-041698, Revision 01, 29 January 2012.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : hbrown Create Date : 2004:03:22 13:13:30Z Modify Date : 2012:02:02 10:36:19Z XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Producer : Acrobat Distiller 9.0.0 (Windows) Creator Tool : FrameMaker 10.0.1 Format : application/pdf Title : WLA321 and WLA322 QSG.fm Creator : hbrown Document ID : uuid:696dc3c8-d45d-43c4-a761-c189561d24fa Instance ID : uuid:a31cab73-b27b-41df-8633-391bbaa66123 Page Mode : UseOutlines Page Count : 2EXIF Metadata provided by EXIF.tools