Junlan Electronic IOTS1010 SMART PLUG User Manual 1

Shenzhen Junlan Electronic Ltd SMART PLUG 1

Users manual

PLEASE READ CAREFULLY BEFORE OPERATING THIS EQUIPMENTKEEP IT IN A SAFE PLACE FOR FUTURE REFERENCEBASIC WIFI SMART PLUGMODEL:AWP48W
2DANGEROUS VOLTAGE:The lighting flash with arrowhead symbol withinan equilateral triangle is intended to alert the user to the presence ofuninsulated “dangerous voltage” within the product’s enclosure that maybe of sufficient magnitude to constitute a risk of electric shock to persons.ATTENTION:The exclamation point within an equilateral triangle is intended toalert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance.WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSETHIS UNIT TO RAIN OR MOISTURE.WARNING: USE UNDER SUPERVISION OF AN ADULT DUE TO LONGCORD This unit has a long cord that can be easily tripped on or pulled on,causing injury. Please make sure it is arranged so that it will not drape over atabletop, etc. Where it can be pulled on by children or tripped over accidentally.FCC STATEMENT:This device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions:(1)This device may not cause harmful interference, and(2)This device must accept any interference received, including interferencethat may cause undesired operation.CAUTION: TO REDUCE THE ELECTRIC SHOCK, DO NOT REMOVE THECOVER (OR BACK). NO USER SERVICEABLE PART INSIDE, REFERSERVICING TO QUALIFIED SERVICE PERSONNEL.CAUTIONRISK OF ELECTRIC SHOCK            DO NOT OPEN
This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one or more ofthe following measures:●Reorient or relocate the receiving antenna.●Increase the separation between the equipment and receiver.●Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.●Consult the dealer or an experienced radio/TV technician for help.FCC WARNING:To assure continued operation, follow the attached installation instructions anduse only shield cables when connecting to other devices. Changes ormodifications not expressly approved by the party responsible for compliancecould void the user's authority to operate the equipment.Before using the unit, be sure to read all operating instruction carefully, pleasenote that these are general precautions and may not pertain to your unit. Forexample, this unit may not have the capability to be connected to an outdoorantenna.1. Read these instructionsAll the safety and operating instructions should be read before the appliance isoperated.2. Keep these instructionsThe safety and operating instructions should be kept for future reference.3. Heed all warningsAll warnings on the appliance and in the operating instructions should beadhered to.4. Follow all instructionsAll operation and use instructions should be followed.FCC NOTICE:5. Do not use this apparatus near waterThe appliance should not be used near water; for example, near a bath tub,3
4washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimmingpool.6. Clean only with dry clothThe appliance should be cleaned only as recommended by the manufacturer.7. Do not block any ventilation openings.Install in accordance with themanufacturer’s instructions.Slots and openings in the cabinet and in the back or bottom are provided forventilation, to ensure reliable operation of the product and to protect it fromoverheating. These openings must not be blocked or covered. The openingsshould never be blocked by placing the product on a bed, sofa, rug, or similarsurface. This product should never be placed near or over a radiator or heatsource. This product should not be placed in a built-in installation, such as abookcase or rack unless proper ventilation is provided or the manufacturer’sinstructions have been adhered to.8. Do not install near any heat sources such as radiators, heat registers,stoves, or other apparatus (including amplifiers) that produce heat.9. Do not defeat the safety purpose of the polarized or grounding-typeplug. A polarized plug has two blades with one wider than the other. Agrounding type plug has two blades and a third grounding prong. Thewide or the third prong are provided for your safety. If the provided plugdoes not fit into your outlet, consult an electrician for replacement of theobsolete outlet.10. Protect the power cord from being walked on or pinched particularlyat plugs, convenience receptacles, and the point where they exit from theapparatus.11. Only use attachments / accessories specified by the manufacturer.12. Use only with a cart, stand, tripod, bracket, or tablespecified by the manufacturer, or sold with the apparatus.When a cart is used, use caution when moving thecart/apparatus combination to avoid injuryfrom tip-over.An appliance and cart combination should be moved with care. Quick stop,excessive fore and uneven surfaces may cause the appliance and cartcombination to overturn.13. Unplug this apparatus during lightning storms or when unused forlong periods of time.To protect your product from a lightning storm, or when it is left unattended andunused for long periods of time, unplug it from the wall outlet and disconnectthe antenna or cable system. This will prevent damage to the product due tolightning and power-line surges.14. Refer all servicing to qualified service personnel. Servicing isrequired when the apparatus has been damaged in any way, such aspower-supply cord or plug is damaged, liquid has been spilled or objectshave fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.15. Power sourceThis product should be operated only from the type of power source indicatedon the marking label. If you are not sure of the type of power supply to yourhome, consult your appliance dealer or local power company. For productsintended to operate from battery power, or other source, refer to the operationinstructions.16. Power linesAn outside antenna system should not be located in the vicinity of overheadpower lines or other electric light or power circuits, or where it can fall into suchpower lines or circuits. When installing an outside antenna system, extremecare should be taken to keep from touching such power lines or circuits ascontact with them might be fatal.17. OverloadingDo not overload wall outlets and extension cords as this can result in a risk offire or electric shock.18. Object and liquid entryNever push objects of any kind into the product through openings as they maytouch dangerous voltage points or short out parts that could result in fire orelectric shock. Never spill or spray any type of liquid on the product.19. Outdoor antenna groundingIf an outside antenna is connected to the product, be sure the antenna systemis grounded so as to provide some protection against voltage surges and builtup static charges. Section 810 of the National Electric Code ANSI/ NFPA 70provides information with respect to proper grounding of the mast andsupporting structure, grounding of the lead- in wire to an antenna dischargeproduct, size of grounding conductors, location of antenna- discharge product,connection to grounding electrodes and requirements for the groundingelectrodes.5
20. ServiceDo not attempt to service this product yourself as opening or removing coversmay expose you to dangerous voltage or other hazards. Refer all servicing toqualified service personnel.b)If liquid has been spilled or objects have fallen into the product.c)If the product has been exposed to rain or water.d)If the product does not operate normally by following the operatinginstructions. Adjust only those controls that are covered by the operatinginstructions, as an adjustment of other controls may result in damage and willrequire extensive work by a qualified technician to restore the product to itsnormal operation.e)If the product has been dropped or the cabinet has been damaged.f)When the product exhibits a distinct change in performance- this indicates aneed for service.25. Note to CATV system installerThis reminder is provided to call the CATV system installer' s attention toArticle 820- 40 of the NEC that provides guidelines for proper grounding and,in particular, specifies that the cable ground shall be connected to thegrounding system of the building, as close to the point of cable entry aspractical.NOTE: Refer all servicing to qualified service personnel. Servicing isrequired when the unit has been damaged in any way such as thefollowing: the power-supply cord or plug has been damaged, liquid hasbeen spilled into unit, the unit has been exposed to rain or moisture, theunit has been dropped or the unit does not operate normally.21. Replacement partsWhen replacement parts are required, be sure the service technician usesreplacement parts specified by the manufacturer or those that have the samecharacteristics as the original parts. Unauthorized substitutions may result infire or electric shock or other hazards.22. Safety checkUpon completion of any service or repairs to this product, ask the servicetechnician to perform safety checks to determine that the product is in properoperating condition.23. Wall or ceiling mountingThe product should be mounted to a wall or ceiling only as recommended bythe manufacturer.24. Damage requiring serviceUnplug this product from the wall outlet and refer service to qualified servicepersonnel under the following conditions.a)When the power- supply cord or plug is damaged.6
7SMART SOCKET OVERVIEW SocketPower ON/OFF ButtonLED RingPress and hold the power button for about 5 seconds in powering on mode, the LED   LED ring will turn red. Press the power button to power on, the Press the power button again to power offPREPARATION Smooth and rapid Wi-Fi network (2.4 GHz only)Smart Life APP and accountOne Smart Device: smart phone or tablet (not included)the LED ring will turn off. ring blinks fast with red and blue color, now it is in pairing mode(EZ mode).Press and hold the power button for about 5 seconds in pairing mode until the LED   ring blinks slowly with blue color, now it is in compatible pairing mode (AP mode).LED Ring Color Smart Socket StatusRed Powering OnNo Color Powering OffBlue and Red or Blue(blink fast) Pairing mode (EZ mode)Blue and Red or Blue(blink slowly) Compatible pairing mode(AP mode)
SMART LIFE APP  1. Search "Smart Life" on Apple APP store or Google Play, download and install it. 2. Once installed successfully, the icon will appear as the figure below.REGISTER SMART LIFE APP 1. Tap the Smart Life App icon to open.Smart Life2. Tap "Register". (If you already have an account, tap "Login" to log in)3. Tap the country columnn to select your country.4. Tap "Mobile Number/Email" column to input your mobile phone number or email address. Tap "Next" to continue.6. Tap "Confirm" to finish registration.5. A verification code will be sent to your mobile phone or inbox on your phone. Input the verification code  into the "verification code" column, then input a password on " Please Input Password" column.(6-20 digit password with letter and number) 8
9CONNECT SMART SOCKET BY SMART LIFE APP  1. Click "Smart Life" App and log in. When the below page appear, click "Add device" to continue.2. When the below page appear, click "Electrical outlet" to continue.3. Press and hold the      button for approx.10 seconds until the LED ring turns Blue and Red and blinking fast, click "Confirm indicator rapidly blink" to continue. CONNECTION THROUGH EZ MODE
104. The window will remind you to confirm the Wi-Fi information."Confirm" to continue.Input the Wi-Fi password and tap 5. The Smart Life is now connecting    the available smart outlets.IMPORTANT!  ONCE DEVICE ADDED,  CLICK        TO RENAME,  OTHERWISE, IT CAN NOT  BE CONTROLLED BY ALEXAVOICE CONTROL.  6. The available smart outlets will be shown as below when successfully connected.
117.  After renaming, tap "Share with family"family can control on  their smart phone with Smart Life APP.and set as on screen instructions to share with family, then yourOr you can set it later and tap "Done" to continue. 8. If connection fails, tap "Retry" to reconnect again as above steps.
CONNECTION THROUGH AP MODE  121. Click "Smart Life" App and log in. When the below page appear, click "Add device" to continue.2. When the below page appear, click "Electrical outlet" to continue.3. Press and hold the      button for approx.15 seconds until the LED ring turns Blue and Red  then it turns blue and blinking slowly, tap "AP Mode" to skip to next interface.
134. Tap "Confirm indicator slowly blink" to continue.  5. The window will remind you to confirm the Wi-Fi information."Confirm" to continue.Input the Wi-Fi password and tap 6. Tap "Connect Now" to skip to your smart phone's wifi setting.  7. Select SmartLift-XXXX then return to APP.
9. The available smart outlets will be shown as below when successfully connected.IMPORTANT!  ONCE DEVICE ADDED,  CLICK        TO RENAME,  OTHERWISE, IT CAN NOT  BE CONTROLLED BY ALEXAVOICE CONTROL.  148. The Smart Life is now connecting    the available smart outlets.
10.  After renaming, tap "Share with family"family can control on  their smart phone with Smart Life APP.and set as on screen instructions to share with family, then yourOr you can set it later and tap "Done" to continue. 1511. If connection fails, tap "Retry" to reconnect again as above steps.
HOME PAGE   1. After completely connection, the home page will appear as below. appear as below.2. Tap "+" at the right top corner to add more device, the connection procedures refer to the previous two connection menthod, after successful addition, the interface will16
HOME PAGE   3. Tap "Scenes" at the bottom of the screen to create your own scene to suit your needs, For example, set your home to automatically turn on the lights and close.4. Tap "+" to add your customized scene, here, tap  "Good night", then you need to finish two steps, step1: add a condition, step2: add a task (if there is no device added, here will be empty, and you need to add a device before this operation).when finish two steps, the "Perform" will be green, and you can tap "Perform" to execute task.17
HOME PAGE   5. Tap "Profiles" at the bottom of the screen to set your profile, create scenes, sharing device, receiving message, using integration(the third side software) to operate by voice control or other operations, tap "Experience Center" to experience the scene, tap "Scan QR Code" to scan the QR code on some of the smart product, tap FAQ to check the requent ask questions. NOTE: For Integration, here you can operate as the screen instructions to operate, expecially you can use Amazon Alexa for voice control operation.18

Navigation menu